TLC552CN [TI]
DUAL LINCMOSE TIMER; 双LINCMOSE定时器型号: | TLC552CN |
厂家: | TEXAS INSTRUMENTS |
描述: | DUAL LINCMOSE TIMER |
文件: | 总9页 (文件大小:136K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TLC552C
DUAL LINCMOS TIMER
SLFS046 – FEBRUARY 1984 – REVISED MAY 1988
D OR N PACKAGE
(TOP VIEW)
Very Low Power Consumption . . . 2 mW
Typ at V = 5 V
DD
Capable of Operation in Astable Mode
DSCH
V
1
2
3
4
5
6
7
14
13
12
11
10
9
DD
CMOS Output Capable of Swinging Rail to
Rail
THRES
CONT
RESET
OUT
DSCH
THRES
CONT
RESET
OUT
TIMER
# 1
High Output-Current Capability
Sink 100 mA Typ
TIMER
# 2
TRIG
Source 10 mA Typ
GND
8
TRIG
Output Fully Compatible With CMOS, TTL,
and MOS
Low Supply Current Reduces Spikes
During Output Transitions
functional block diagram (each timer)
12
High-Impedance Inputs . . . 10 Ω Typ
RESET
V
DD
CONT
Single-Supply Operation From 1 V to 18 V
R
Functionally Interchangeable With the
NE556; Has Same Pinout
R1
R
THRES
1
OUT
description
S
R
The TLC552 is a dual monolithic timing circuit
fabricated using TI LinCMOS process, which
provides full compatibility with CMOS, TTL, and
MOS logic and operation at frequencies up to
2 MHz. Accurate time delays and oscillations are
possible with smaller, less-expensive timing
capacitors than the NE555 because of the high
input impedance. Power consumption is low
across the full range of power supply voltages.
TRIG
R
DSCH
GND
RESET can override TRIG and THRES.
TRIG can override THRES.
Like the NE556, the TLC552 has a trigger level
approximately one-third of the supply voltage and
a threshold level approximately two-thirds of the
supplyvoltage. Theselevelscanbealteredbyuse
of the control voltage terminal. When the trigger
input falls below the trigger level, the flip-flop is set
and the output goes high. If the trigger input is
above the trigger level and the threshold input is
above the threshold level, the flip-flop is reset and
AVAILABLE OPTIONS
SYMBOLIZATION
OPERATING
V
max
T
TEMPERATURE
RANGE
PACKAGE
SUFFIX
DEVICE
at 25°C
TLC552C
D,N
0°C to 70°C
3.8 mV
The D packages are available taped and reeled. Add the suffix R
to the device type when ordering (i.e., TLC552CDR).
the output is low. The reset input can override all other inputs and can be used to initiate a new
timing cycle. If the reset input is low, the flip-flop is reset and the output is low. Whenever the output is low, a
low-impedance path is provided between the discharge terminal and ground.
Whilethe CMOS output is capable of sinking over 100 mA and sourcing over 10 mA, the TLC552 exhibits greatly
reduced supply-current spikes during output transitions. This minimizes the need for the large decoupling
capacitors required by the NE556.
LinCMOS is a trademark of Texas Instruments Incorporated.
Copyright 1988, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC552C
DUAL LINCMOS TIMER
SLFS046 – FEBRUARY 1984 – REVISED MAY 1988
description (continued)
These devices have internal electrostatic discharge (ESD) protection circuits that will prevent catastrophic
failures at voltages up to 2000 V as tested under MIL-STD-883C, Method 3105.2. However, care should be
exercised in handling these devices as exposure to ESD may result in a degradation of the device parametric
performance.
All unused inputs should be tied to an appropriate logic level to prevent false triggering.
The TLC552C is characterized for operation from 0°C to 70°C.
FUNCTION TABLE
TRIGGER
THRESHOLD
DISCHARGE
SWITCH
†
RESET VOLTAGE
OUTPUT
†
†
VOLTAGE
Irrelevant
< MIN
VOLTAGE
Irrelevant
Irrelevant
> MAX
< MIN
> MAX
> MAX
> MAX
Low
High
Low
On
Off
On
> MAX
> MAX
< MIN
As previously established
†
For conditions shown as MIN or MAX, use the appropriate value specified under electrical characteristics.
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage, V
(see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V
DD
Input voltage range (any input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 0.3 V to V
DD
Sink current, DSCH or OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150 mA
Source current, OUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 mA
Continuous total dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
Operating free-air temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 75°C
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . – 65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
NOTES: 1. All voltage values are with respect to network ground terminal.
DISSIPATION RATING TABLE
PACKAGE
POWER RATING
DERATING FACTOR
ABOVE T
A
D
N
950 mW
1150 mW
7.6 mW/°C
9.2 mW/°C
25°C
25°C
recommended operating conditions
MIN
1
MAX
18
UNIT
V
Supply voltage, V
DD
Operating free-air temperature range, T
0
70
°C
A
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC552C
DUAL LINCMOS TIMER
SLFS046 – FEBRUARY 1984 – REVISED MAY 1988
electrical characteristics at specified free-air temperature, V
= 1 V
DD
†
PARAMETER
TEST CONDITIONS
T
A
MIN
0.475
0.45
TYP MAX
UNIT
25°C
Full range
25°C
0.67
0.85
Threshold voltage level
Threshold current
Trigger voltage level
Trigger current
V
0.875
10
75
pA
V
MAX
25°C
0.15
0.1
0.33 0.425
Full range
25°C
1.45
10
75
pA
V
MAX
25°C
0.4
0.3
0.7
1
1
Reset voltage level
Reset current
Full range
25°C
10
75
pA
MAX
Control voltage (open-circuit) as a percentage of supply voltage
Discharge switch on-state voltage
MAX
66.7%
0.02
25°C
0.15
0.2
I
= 100 µA
V
nA
V
OL
Full range
25°C
0.1
0.5
Discharge switch off-state current
Low-level output voltage
High-level output voltage
Supply current
MAX
25°C
0.03
0.2
I
I
= 100 µA
= –10 µA
OL
Full range
25°C
0.25
0.6
0.6
0.98
30
V
OH
Full range
25°C
200
300
µA
Full range
†
Full range (MIN to MAX) is 0°C to 70°C.
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC552C
DUAL LINCMOS TIMER
SLFS046 – FEBRUARY 1984 – REVISED MAY 1988
electrical characteristics at specified free-air temperature, V
= 2 V
DD
†
PARAMETER
TEST CONDITIONS
T
A
MIN
0.95
0.85
TYP MAX
UNIT
25°C
Full range
25°C
1.33
1.65
1.75
Threshold voltage level
Threshold current
Trigger voltage level
Trigger current
V
10
75
pA
V
MAX
25°C
0.4
0.3
0.67
0.95
1.05
Full range
25°C
10
75
pA
V
MAX
25°C
0.4
0.3
1.1
1.5
1.8
Reset voltage level
Reset current
Full range
25°C
10
75
pA
MAX
Control voltage (open-circuit) as a percentage of supply voltage
Discharge switch on-state voltage
MAX
66.7%
0.03
25°C
0.2
I
= 1 mA
V
nA
V
OL
Full range
25°C
0.25
0.1
0.5
Discharge switch off-state current
Low-level output voltage
High-level output voltage
Supply current
MAX
25°C
0.07
0.3
I
I
= 1 mA
OL
Full range
25°C
0.35
1.5
1.5
1.9
= –300 µA
V
OH
Full range
25°C
130
500
800
µA
Full range
†
Full range (MIN to MAX) is 0°C to 70°C.
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC552C
DUAL LINCMOS TIMER
SLFS046 – FEBRUARY 1984 – REVISED MAY 1988
electrical characteristics at specified free-air temperature, V
= 5 V
DD
†
PARAMETER
TEST CONDITIONS
T
A
MIN
2.8
TYP
MAX
3.8
UNIT
25°C
Full range
25°C
3.3
Threshold voltage level
Threshold current
Trigger voltage level
Trigger current
V
2.7
3.9
10
75
pA
V
MAX
25°C
1.36
1.26
1.66
1.96
2.06
Full range
25°C
10
75
pA
V
MAX
25°C
0.4
0.3
1.1
1.5
1.8
Reset voltage level
Reset current
Full range
25°C
10
75
pA
MAX
Control voltage (open-circuit) as a percentage of supply voltage
Discharge switch on-state voltage
MAX
66.7%
0.14
25°C
0.5
0.6
I
= 10 mA
V
OL
Full range
25°C
0.1
0.5
Discharge switch off-state current
nA
MAX
25°C
0.21
0.4
0.5
I
I
I
I
= 8 mA
OL
OL
OL
OH
Full range
25°C
0.13
0.08
4.8
0.3
Low-level output voltage
= 5 mA
V
Full range
25°C
0.4
0.3
= 3.2 mA
= –1 mA
Full range
25°C
0.35
4.1
4.1
High-level output voltage
Supply current
V
Full range
25°C
340
700
µA
Full range
1000
†
Full range (MIN to MAX) is 0°C to 70°C.
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC552C
DUAL LINCMOS TIMER
SLFS046 – FEBRUARY 1984 – REVISED MAY 1988
electrical characteristics at specified free-air temperature, V
= 15 V
DD
†
PARAMETER
TEST CONDITIONS
T
A
MIN
9.45
9.35
TYP
MAX
UNIT
25°C
Full range
25°C
10 10.55
10.65
10
Threshold voltage level
Threshold current
Trigger voltage level
Trigger current
V
pA
V
MAX
75
25°C
4.65
4.55
5
5.35
5.45
Full range
25°C
10
75
pA
V
MAX
25°C
0.4
0.3
1.1
1.5
1.8
Reset voltage level
Reset current
Full range
25°C
10
75
pA
MAX
Control voltage (open-circuit) as a percentage of supply voltage
Discharge switch on-state voltage
MAX
66.7%
0.77
25°C
1.7
1.8
I
= 100 mA
V
OL
Full range
25°C
0.1
0.5
Discharge switch off-state current
nA
MAX
25°C
1.28
3.2
3.6
1
I
I
I
I
I
I
= 100 mA
= 50 mA
= 10 mA
= –10 mA
= –5 mA
= –1 mA
OL
OL
OL
OH
OH
OH
Full range
25°C
0.63
0.12
14.2
14.6
14.9
0.72
Low-level output voltage
V
Full range
25°C
1.3
0.3
0.4
Full range
25°C
12.5
12.5
13.5
13.5
14.2
14.2
Full range
25°C
High-level output voltage
Supply current
V
Full range
25°C
Full range
25°C
1.2
1.6
mA
Full range
†
Full range (MIN to MAX) is 0°C to 70°C.
6
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC552C
DUAL LINCMOS TIMER
SLFS046 – FEBRUARY 1984 – REVISED MAY 1988
electrical characteristics at specified free-air temperature, V
= 18 V
DD
†
PARAMETER
TEST CONDITIONS
T
A
MIN
11.4
10.9
TYP
MAX
12.6
12.7
UNIT
25°C
Full range
25°C
12
Threshold voltage level
Threshold current
Trigger voltage level
Trigger current
V
10
75
6
pA
V
MAX
25°C
5.6
5.5
6.4
6.5
Full range
25°C
10
75
pA
V
MAX
25°C
0.4
0.3
1.1
1.5
1.8
Reset voltage level
Reset current
Full range
25°C
10
75
pA
MAX
Control voltage (open-circuit) as a percentage of supply voltage
Discharge switch on-state voltage
MAX
66.7%
0.72
25°C
1.5
1.6
I
= 100 mA
V
nA
V
OL
Full range
25°C
0.1
0.5
Discharge switch off-state current
Low-level output voltage
High-level output voltage
Supply current
MAX
25°C
0.04
0.3
I
I
= 3.2 mA
= –1 mA
OL
Full range
25°C
0.35
17.3
17.3
17.9
0.84
V
OH
Full range
25°C
1.2
1.6
mA
Full range
†
Full range (MIN to MAX) is 0°C to 70°C.
operating characteristics, V
= 5 V, T = 25°C (unless otherwise noted)
DD
A
PARAMETER
TEST CONDITIONS
MIN
TYP
1%
0.1
20
MAX
3%
0.5
75
UNIT
‡
Initial error of timing interval
V
C
= 5 V to 15 V,
R = R = 1 kΩ to 100 kΩ,
A B
See Note 2
DD
T
= 0.1 µF,
Supply voltage sensitivity of timing interval
Output pulse rise time
%/V
ns
R
= 10 MΩ,
C
R
= 10 pF
L
L
Output pulse fall time
15
60
R
C
= 470 Ω,
= 200 pF,
= 200 Ω,
A
T
B
Maximum frequency in astable mode
1.2
2.8
MHz
See Note 2
‡
Timing interval error is defined as the difference between the measured value and the nominal value of a random sample.
NOTE 2: R , R , and C are as defined in Figure 1.
A
B
T
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLC552C
DUAL LINCMOS TIMER
SLFS046 – FEBRUARY 1984 – REVISED MAY 1988
APPLICATION INFORMATION
V
DD
0.1 µF
R
A
0.1 µF
CONT
V
DD
R
L
RESET
DISCH
Output
OUT
R
B
THRES
TRIG
C
L
C
GND
T
Figure 1. Circuit for Astable Operation
8
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments and its subsidiaries (TI) reserve the right to make changes to their products or to discontinue
any product or service without notice, and advise customers to obtain the latest version of relevant information
to verify, before placing orders, that information being relied on is current and complete. All products are sold
subject to the terms and conditions of sale supplied at the time of order acknowledgement, including those
pertaining to warranty, patent infringement, and limitation of liability.
TI warrants performance of its semiconductor products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are utilized to the extent
TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily
performed, except those mandated by government requirements.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF
DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE (“CRITICAL
APPLICATIONS”). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, AUTHORIZED, OR
WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT DEVICES OR SYSTEMS OR OTHER
CRITICAL APPLICATIONS. INCLUSION OF TI PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO
BE FULLY AT THE CUSTOMER’S RISK.
In order to minimize risks associated with the customer’s applications, adequate design and operating
safeguards must be provided by the customer to minimize inherent or procedural hazards.
TI assumes no liability for applications assistance or customer product design. TI does not warrant or represent
that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other
intellectual property right of TI covering or relating to any combination, machine, or process in which such
semiconductor products or services might be or are used. TI’s publication of information regarding any third
party’s products or services does not constitute TI’s approval, warranty or endorsement thereof.
Copyright 1998, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明