TLV320DAC3100-Q1_15 [TI]
Low-Power Stereo Audio DAC With Audio Processing and Mono Class-D Speaker Amplifier;型号: | TLV320DAC3100-Q1_15 |
厂家: | TEXAS INSTRUMENTS |
描述: | Low-Power Stereo Audio DAC With Audio Processing and Mono Class-D Speaker Amplifier |
文件: | 总101页 (文件大小:1376K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
Low-Power Stereo Audio DAC With Audio Processing
and Mono Class-D Speaker Amplifier
Check for Samples: TLV320DAC3100-Q1
1 INTRODUCTION
1.1 Features
Playback Volume-Control Settings
• Digital Sine-Wave Generator for Beeps and Key
Clicks (PRB_P25)
123
• Qualified for Automotive Applications
• AEC-Q100 Qualified with the Following Results:
• Programmable PLL for Flexible Clock
Generation
– Device Temperature Grade 3: –40°C to 85°C
Ambient Operating Temperature Range
– Device HBM ESD Classification Level H2
– Device CDM ESD Classification Level C4B
• Stereo Audio DAC with 95-dB SNR
• I2S, Left-Justified, Right-Justified, DSP, and
TDM Audio Interfaces
• I2C Control With Register Auto-Increment
• Full Power-Down Control
• Power Supplies:
• Supports 8-kHz to 192-kHz Sample Rates
• Mono Class-D BTL Speaker Driver (2.5 W Into
– Analog: 2.7 V–3.6 V
– Digital Core: 1.65 V–1.95 V
– Digital I/O: 1.1 V–3.6 V
4-Ω or 1.6 W Into 8-Ω)
• Two Single-Ended Inputs With Mixing and
Output Level Control
• Stereo Headphone/Lineout and Mono Class-D
Speaker Outputs Available
– Class-D: 2.7 V–5.5 V (SPKVDD ≥ AVDD)
• 5-mm × 5-mm 32-QFN Package
• Microphone Bias
• Headphone Detection
1.2 Applications
•
•
•
•
Automotive Applications
Portable Audio Devices
Mobile Internet Devices
eBooks
• 25 Built-in Digital Audio Processing Blocks
(PRB_P1 – PRB_P25) Providing Biquad and FIR
Filters, DRC, and 3-D Structures
• Digital Mixing Capability
• Pin Control or Register Control for Digital-
1.3 Description
The TLV320DAC3100-Q1 is a low-power, highly-integrated, high-performance stereo-audio DAC with 24-bit
stereo playback and digital audio processing blocks.
The device integrates headphone drivers and speaker drivers. The mono speaker driver drives loads down to 4
Ω. The TLV320DAC3100-Q1 has a suite of built-in processing blocks for digital audio processing. The digital
audio data format is programmable to work with popular audio standard protocols (I2S, left and right-justified) in
master, slave, DSP, and TDM modes. Bass boost, treble, or EQ is supported by the programmable digital signal-
processing block. An on-chip PLL provides the high-speed clock required by the digital signal-processing block.
The volume level is controlled either by pin control or by register control. The audio functions are controlled using
the I2C serial bus.
The TLV320DAC3100-Q1 has a programmable digital sine-wave generator and is available in a 32-pin QFN
package.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
3
MATLAB is a trademark of The MathWorks, Inc.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Products conform to
specifications per the terms of the Texas Instruments standard warranty. Production
processing does not necessarily include testing of all parameters.
Copyright © 2013, Texas Instruments Incorporated
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
AVSS
AVDD
HPVSS
HPVDD
SPKVSS
SPKVSS
SPKVDD
SPKVDD
P0/R116
7-Bit
Vol
ADC
VOL/MICDET
Audio Output Stage
Power Management
Left and Right
Volume-Control Register
P0/R117
P1/R33–R34
GPIO1
GPIO
I2C
De-Pop
and
Soft Start
SDA
SCL
RC CLK
AIN1
AIN2
Analog
Mono Class-D
Speaker Driver
Note: Normally,
Attenuation
0 dB to –78 dB
and Mute
MCLK is PLL input;
however, BCLK or
GPIO1 can also be
6 dB to 24 dB
(6-dB Steps)
(0.5-dB Steps)
P0/R63/D5–D4
PLL input.
Left DAC
P1/R38
P1/R42
AIN1
SPKP
SPKP
SPKM
SPKM
L Data
R Data
(L+R)/2 Data
DAC
S
MCLK
PLL
P0/R64
Analog
Class A/B
Attenuation Headphone/Lineout
Driver
0 dB to 9 dB
(1-dB Steps)
0 dB to –78 dB
and Mute
(0.5-dB Steps)
WCLK
DIN
P1/R40
P1/R36
BCLK
Serial
Interface
and
Process- Digital Vol
24 dB to
Mute
AIN2
HPL
ing
Blocks
MIXER
P1/R35
Clocks
RESET
Analog
Class-A/B
Headphone/Lineout
Driver
Attenuation
0 dB to –78 dB
and Mute
0 dB to 9 dB
(1-dB Steps)
(0.5-dB Steps)
P0/R63/D3–D2
Right DAC
DAC
P1/R37
P1/R41
L Data
R Data
(L+R)/2 Data
HPR
S
P0/R64
P0/R64–R66
P1/R46
2 V/2.5 V/AVDD
MICBIAS
IOVDD
DVSS
DVDD
IOVSS
B0360-03
Figure 1-1. Functional Block Diagram
NOTE
This data manual is designed using PDF document-viewing features that allow quick access
to information. For example, performing a global search on "page 0 / register 27" produces
all references to this page and register in a list. This makes it easy to traverse the list and
find all information related to a page and register. Note that the search string must be of the
indicated format. Also, this document includes document hyperlinks to allow the user to find
a document reference quickly. To come back to the original page, click the green left arrow
near the PDF page number at the bottom of the file. The hot-key for this function is alt-left
arrow on the keyboard. Another way to find information quickly is to use the PDF bookmarks.
2
INTRODUCTION
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
2 PACKAGE AND SIGNAL DESCRIPTIONS
2.1 Package/Ordering Information
See the Package Option Addendum at the end of this data manual for information regarding the device
package and ordering of parts.
2.2 Device Information
RHB Package
(Top View)
24 23 22 21 20 19 18 17
25
26
27
28
29
30
31
32
16
15
14
13
12
11
10
9
SPKVSS
AVSS
NC
SPKP
HPL
AIN2
HPVDD
HPVSS
HPR
AIN1
MICBIAS
VOL/MICDET
SCL
RESET
GPIO1
SDA
1
2
3
4
5
6
7
8
P0048-16
Table 2-1. TERMINAL FUNCTIONS
TERMINAL
I/O
DESCRIPTION
NAME
AIN1
NO.
13
14
17
16
7
I
I
Analog input No. 1 routed to output mixer
Analog input No. 2 routed to output mixer
Analog power supply
AIN2
AVDD
AVSS
BCLK
DIN
–
–
I/O
I
Analog ground
Audio serial bit clock
5
Audio serial data input
DVDD
DVSS
GPIO1
HPL
3
–
–
I/O
O
O
–
–
–
–
I
Digital power – digital core
Digital ground
18
32
27
30
28
29
2
General-purpose input/output pin and multifunction pin
Left-channel headphone/line driver output
Right-channel headphone/line driver output
Headphone/line driver and PLL power
Headphone/line driver and PLL ground
Interface power
HPR
HPVDD
HPVSS
IOVDD
IOVSS
MCLK
MICBIAS
NC
1
Interface ground
8
External master clock
12
4, 15
31
–
I
Microphone bias voltage
No connection
RESET
I
Device reset
Copyright © 2013, Texas Instruments Incorporated
PACKAGE AND SIGNAL DESCRIPTIONS
3
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
Table 2-1. TERMINAL FUNCTIONS (continued)
TERMINAL
I/O
DESCRIPTION
NAME
SCL
NO.
10
I/O
I/O
I/O
–
I2C control bus clock input
I2C control-bus data input
SDA
9
SPKM
SPKP
19, 23
22, 26
21, 24
20, 25
Cass-D speaker driver inverting output
Class-D speaker driver noninverting output
Class-D speaker driver power supply
SPKVDD
SPKVSS
–
–
Class-D speaker driver power-supply ground
Volume control or headphone detection. Note that microphone detection is also available on
devices that have an ADC.
VOL/MICDET
WCLK
11
6
I
I/O
Audio serial word clock
4
PACKAGE AND SIGNAL DESCRIPTIONS
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
3 ELECTRICAL SPECIFICATIONS
3.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)
(1)
VALUE
MIN
UNIT
MAX
AVDD to AVSS
–0.3
–0.3
3.9
V
V
V
V
V
V
V
DVDD to DVSS
2.5
HPVDD to HPVSS
–0.3
3.9
SPKVDD to SPKVSS
IOVDD to IOVSS
–0.3
6
–0.3
3.9
Digital input voltage
IOVSS – 0.3
AVSS – 0.3
–40
IOVDD + 0.3
Analog input voltage
Ambient temperature range (TA)
Storage temperature range
Junction temperature (TJ Max)
AVDD + 0.3
85
150
125
2
–55
°C
Human-body model (HBM) AEC-Q100 classification level H2
kV
V
ESD Ratings
Charged-device model (CDM) AEC-Q100 classification level
C4B
750
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
3.2 THERMAL INFORMATION
TLV320DAC3100-Q1
THERMAL METRIC
UNITS
RHB (32 PINS)
θJA
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
31.9
22.6
6
θJCtop
θJB
°C/W
ψJT
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
0.2
6
ψJB
θJCbot
1.3
3.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
2.7
NOM
MAX
3.6
UNIT
AVDD(1)
DVDD
Referenced to AVSS(2)
3.3
1.8
3.3
(2)
Referenced to DVSS
1.65
2.7
1.95
3.6
Power-supply voltage range
V
HPVDD
SPKVDD(1)
IOVDD
Referenced to HPVSS(2)
(2)
Referenced to SPKVSS
Referenced to IOVSS
2.7
5.5
1.1
3.3
3.6
Resistance applied across class-D ouput pins
(BTL)
Speaker impedance
4
Ω
Ω
Headphone impedance
AC coupled to RL
16
Analog audio full-scale input
voltage
VI
AVDD = 3.3 V, single-ended
0.707
VRMS
(1) To minimize battery-current leakage, the SPKVDD voltage level should not be below the AVDD voltage level.
(2) All grounds on board are tied together, so they should not differ in voltage by more than 0.2-V maximum for any combination of ground
ignals. By use of a wide trace or ground plane, ensure a low-impedance connection between HPVSS and DVSS.
Copyright © 2013, Texas Instruments Incorporated
ELECTRICAL SPECIFICATIONS
5
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
Recommended Operating Conditions (continued)
over operating free-air temperature range (unless otherwise noted)
MIN
NOM
MAX
UNIT
Stereo line output load
AC coupled to RL
impedance
10
kΩ
MCLK(3)
fSCL
Master clock frequency
SCL clock frequency
IOVDD = 3.3 V
50
400
85
MHz
kHz
°C
TA
Operating free-air temperature
–40
(3) The maximum input frequency should be 50 MHz for any digital pin used as a general-purpose clock.
3.4 Electrical Characteristics
At 25°C, AVDD = HPVDD = IOVDD = 3.3 V, SPKVDD = 3.6 V, DVDD = 1.8 V, fS (audio) = 48 kHz, CODEC_CLKIN = 256 ×
fS, PLL = Off, VOL/MICDET pin disabled (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
INTERNAL OSCILLATOR-RC_CLK
Oscillator frequency
8.2
MHz
VOLUME CONTROL PIN (ADC); VOL/MICDET pin enabled
VOL/MICDET pin configured as volume control (page 0 / register 116, bit D7 = 1 and
page 0 / register 67, bit D7 = 0)
0.5 x
AVDD
Input voltage range
0
V
Input capacitance
2
pF
Volume control steps
128
Steps
Microphone Bias
Page 1 / register 46, bits D1–D0 = 10
2.25
2.5
2
2.75
Voltage output
V
Page 1 / register 46, bits D1–D0 = 01
At 4-mA load current, page 1 / register 46, bits D1–D0 = 10 (MICBIAS = 2.5 V)
At 4-mA load current, page 1 / register 46, bits D1–D0 = 01 (MICBIAS = 2 V)
5
Voltage regulation
mV
7
AUDIO DAC
DAC HEADPHONE OUTPUT, AC-coupled load = 16 Ω (single-ended), driver gain = 0 dB, parasitic capacitance = 30 pF
Full-scale output voltage (0 dB)
Signal-to-noise ratio
Output common-mode setting = 1.65 V
Measured as idle-channel noise, A-weighted(1)
0-dBFS input
0.707
95
VRMS
dB
(2)
SNR
80
THD
Total harmonic distortion
Total harmonic distortion + noise
Mute attenuation
–85
–82
87
–65
–60
dB
THD+N
0-dBFS input
dB
dB
PSRR
PO
Power-supply rejection ratio(3)
Ripple on HPVDD (3.3 V) = 200 mVp-p at 1 kHz
RL = 32 Ω, THD+N = –60 dB
–62
20
dB
Maximum output power
mW
RL = 16 Ω, THD+N = –60 dB
60
DAC LINEOUT (HP Driver in Lineout Mode)
SNR
Signal-to-noise ratio
Measured as idle-channel noise, A-weighted
0-dBFS input, 0-dB gain
95
–86
–82
dB
dB
dB
THD
Total harmonic distortion
Total harmonic distortion + noise
THD+N
0-dBFS input, 0-dB gain
DAC Digital Interpolation Filter Characteristics
See Section 5.5.1.4 for DAC interpolation filter characteristics.
DAC Output to Class-D SPEAKER OUTPUT; Load = 4 Ω (Differential), 50 pF
SPKVDD = 3.6 V, BTL measurement, DAC input = 0 dBFS, CM = 1.8 V, class-D gain
= 6 dB, THD = –16.5 dB
2.3
Output voltage
VRMS
SPKVDD = 3.6 V, BTL measurement, DAC input = –2 dBFS, CM = 1.8 V, class-D
gain = 6 dB, THD = –20 dB
2.1
1.8
88
Output, common-mode
Signal-to-noise ratio
SPKVDD = 3.6 V, BTL measurement, DAC input = mute, class-D gain = 6 dB
V
SPKVDD = 3.6 V, BTL measurement, class-D gain = 6 dB, measured as idle-channel
SNR
THD
dB
(1) (2)
noise, A-weighted (with respect to full-scale output value of 2.3 VRMS
)
SPKVDD = 3.6 V, BTL measurement, DAC input = –6 dBFS, CM = 1.8 V, class-D
gain = 6 dB
Total harmonic distortion
–65
dB
(1) Ratio of output level with 1-kHz full-scale sine-wave input, to the output level with the inputs short-circuited, measured A-weighted over a
20-Hz to 20-kHz bandwidth using an audio analyzer.
(2) All performance measurements done with 20-kHz low-pass filter and, where noted, A-weighted filter. Failure to use such a filter may
result in higher THD+N and lower SNR and dynamic range readings than shown in the Electrical Characteristics. The low-pass filter
removes out-of-band noise, which, although not audible, may affect dynamic specification values.
(3) DAC to headphone-out PSRR measurement is calculated as PSRR = 20 × log (ΔVHPL / ΔVHPVDD).
6
ELECTRICAL SPECIFICATIONS
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
Electrical Characteristics (continued)
At 25°C, AVDD = HPVDD = IOVDD = 3.3 V, SPKVDD = 3.6 V, DVDD = 1.8 V, fS (audio) = 48 kHz, CODEC_CLKIN = 256 ×
fS, PLL = Off, VOL/MICDET pin disabled (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SPKVDD = 3.6 V, BTL measurement, DAC input = –6 dBFS, CM = 1.8 V, lass-D gain
= 6 dB
THD+N
PSRR
Total harmonic distortion + noise
–63
dB
Power-supply rejection ratio(4)
Mute attenuation
SPKVDD = 3.6 V, BTL measurement, ripple on SPKVDD = 200 mVp-p at 1 kHz
–44
110
1
dB
dB
W
SPKVDD = 3.6 V, BTL measurement, CM = 1.8 V, class-D gain = 18 dB, THD = 10%
SPKVDD = 4.3 V, BTL measurement, CM = 1.8 V, class-D gain = 18 dB, THD = 10%
SPKVDD = 5.5 V, BTL measurement, CM = 1.8 V, class-D gain = 18 dB, THD = 10%
PO
Maximum output power
1.5
2.5
W
W
DAC Output to Class-D Speaker Output; Load = 8 Ω (Differential), 50 pF
SPKVDD = 3.6 V, BTL measurement, DAC input = 0 dBFS, CM = 1.8 V, class-D gain
= 6 dB, THD = –16.5 dB
2.2
VRMS
Output voltage
SPKVDD = 3.6 V, BTL measurement, DAC input = –2 dBFS, CM = 1.8 V, class-D
gain = 6 dB, THD = –20 dB
2.1
1.8
87
VRMS
V
Output, common-mode
Signal-to-noise ratio
SPKVDD = 3.6 V, BTL measurement, DAC input = mute, class-D gain = 6 dB
SPKVDD = 3.6 V, BTL measurement, class-D gain = 6 dB, measured as idle-channel
noise, A-weighted (with respect to full-scale output value of 2.2 VRMS)
SNR
THD
dB
SPKVDD = 3.6 V, BTL measurement, DAC input = –6 dBFS, CM = 1.8 V, class-D
gain = 6 dB
Total harmonic distortion
–67
–66
dB
dB
SPKVDD = 3.6 V, BTL measurement, DAC input = –6 dBFS, CM = 1.8 V, class-D
gain = 6 dB
THD+N
PSRR
Total harmonic distortion + noise
Power-supply rejection ratio(4)
Mute attenuation
SPKVDD = 3.6 V, BTL measurement, ripple on SPKVDD = 200 mVp-p at 1 kHz
–44
110
0.7
1
dB
dB
SPKVDD = 3.6 V, BTL measurement, CM = 1.8 V, class-D gain = 18 dB, THD = 10%
SPKVDD = 4.3 V, BTL measurement, CM = 1.8 V, class-D gain = 18 dB, THD = 10%
SPKVDD = 5.5 V, BTL measurement, CM = 1.8 V, class-D gain = 18 dB, THD = 10%
PO
Maximum output power
W
1.6
Output-stage leakage current for direct
battery connection
SPKVDD = 4.3 V, device is powered down (power-up-reset condition)
80
nA
DAC POWER CONSUMPTION
For DAC power consumption based on the selected processing block, see Section 5.3.
DIGITAL INPUT/OUTPUT
Logic family
CMOS
0.7 ×
IOVDD
IIH = 5 µA, IOVDD ≥ 1.6 V
VIH
IIH = 5 µA, IOVDD < 1.6 V
IOVDD
–0.3
0.3 ×
IIL = 5 µA, IOVDD ≥ 1.6 V
IOVDD
VIL
Logic Level
V
IIL = 5 µA, IOVDD < 1.6 V
0
0.8 ×
IOVDD
VOH
VOL
IOH = 2 TTL loads
IOL = 2 TTL loads
0.1 ×
IOVDD
Capacitive load
10
pF
(4) DAC to speaker-out PSRR is a differential measurement calculated as PSRR = 20 × log (ΔVSPK(P + M) / ΔVSPKVDD) .
Copyright © 2013, Texas Instruments Incorporated
ELECTRICAL SPECIFICATIONS
7
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
3.5 Timing Characteristics
3.5.1 I2S, LJF, and RJF Timing in Master Mode
TA = 25° (unless otherwise noted), DVDD = 1.8 V
Note: All timing specifications are measured at characterization .
WCLK
td(WS)
tr
BCLK
tf
tS(DI)
th(DI)
DIN
T0145-10
IOVDD = 1.1 V
IOVDD = 3.3 V
PARAMETER
UNIT
MIN
MAX
MIN
MAX
td(WS)
ts(DI)
th(DI)
tr
WCLK delay
DIN setup
DIN hold
45
20
ns
ns
ns
ns
ns
8
8
6
6
Rise time
Fall time
25
25
10
10
tf
Figure 3-1. I2S, LJF, and RJF Timing in Master Mode
8
ELECTRICAL SPECIFICATIONS
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
3.5.2 I2S, LJF, and RJF Timing in Slave Mode
TA = 25° (unless otherwise noted), DVDD = 1.8 V
Note: All timing specifications are measured at characterization .
WCLK
th(WS)
tr
tH(BCLK)
tS(WS)
BCLK
tL(BCLK)
tS(DI)
tf
DIN
th(DI)
T0145-11
IOVDD = 1.1 V
IOVDD = 3.3 V
PARAMETER
UNIT
MIN
35
35
8
MAX
MIN
35
35
6
MAX
tH(BCLK)
tL(BCLK)
ts(WS)
th(WS)
ts(DI)
th(DI)
tr
BCLK high period
BCLK low period
WCLK setup
WCLK hold
DIN setup
ns
ns
ns
ns
ns
ns
ns
ns
8
6
8
6
DIN hold
8
6
Rise time
4
4
4
4
tf
Fall time
Figure 3-2. I2S, LJF, and RJF Timing in Slave Mode
Copyright © 2013, Texas Instruments Incorporated
ELECTRICAL SPECIFICATIONS
9
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
3.5.3 DSP Timing in Master Mode
TA = 25° (unless otherwise noted), DVDD = 1.8 V
Note: All timing specifications are measured at characterization .
WCLK
td(WS)
td(WS)
tf
BCLK
tS(DI)
tr
DIN
th(DI)
T0146-09
IOVDD = 1.1 V
IOVDD = 3.3 V
PARAMETER
UNIT
MIN
MAX
MIN
MAX
td(WS)
ts(DI)
th(DI)
tr
WCLK delay
DIN setup
DIN hold
45
20
ns
ns
ns
ns
ns
8
8
8
8
Rise time
Fall time
25
25
10
10
tf
Figure 3-3. DSP Timing in Master Mode
10
ELECTRICAL SPECIFICATIONS
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
3.5.4 DSP Timing in Slave Mode
TA = 25° (unless otherwise noted), DVDD = 1.8 V
Note: All timing specifications are measured at characterization .
WCLK
tS(WS)
th(WS)
tS(WS)
th(WS)
tL(BCLK)
tf
BCLK
tH(BCLK)
tS(DI)
tr
DIN
th(DI)
T0146-10
IOVDD = 1.1 V
IOVDD = 3.3 V
PARAMETER
UNIT
MIN
35
35
8
MAX
MIN
35
35
8
MAX
tH(BCLK)
tL(BCLK)
ts(WS)
th(WS)
ts(DI)
th(DI)
tr
BCLK high period
BCLK low period
WCLK setup
WCLK hold
DIN setup
ns
ns
ns
ns
ns
ns
ns
ns
8
8
8
8
DIN hold
8
8
Rise time
4
4
4
4
tf
Fall time
Figure 3-4. DSP Timing in Slave Mode
Copyright © 2013, Texas Instruments Incorporated
ELECTRICAL SPECIFICATIONS
11
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
3.5.5 I2C Interface Timing
TA = 25° (unless otherwise noted), DVDD = 1.8 V
Note: All timing specifications are measured at characterization .
SDA
tBUF
tLOW
tr
tHIGH
tf
tHD;STA
SCL
tHD;STA
tSU;DAT
tHD;DAT
tSU;STO
tSU;STA
STO
STA
STA
STO
T0295-02
Standard Mode
MIN TYP
Fast Mode
PARAMETER
SCL clock frequency
UNIT
MAX
MIN
TYP
MAX
400
fSCL
0
100
0
kHz
Hold time (repeated) START condition.
After this period, the first clock pulse is
generated.
tHD;STA
4
0.8
μs
tLOW
tHIGH
LOW period of the SCL clock
HIGH period of the SCL clock
4.7
4
1.3
0.6
μs
μs
Setup time for a repeated START
condition
Data hold time: for I2C bus devices
tSU;STA
4.7
0
0.8
μs
tHD;DAT
tSU;DAT
tr
3.45
0
100
0.9
μs
ns
ns
ns
μs
Data set-up time
250
SDA and SCL rise time
1000
300
20 + 0.1Cb
20 + 0.1Cb
0.8
300
300
tf
SDA and SCL fall time
tSU;STO
Set-up time for STOP condition
4
Bus free time between a STOP and
START condition
tBUF
Cb
4.7
1.3
μs
Capacitive load for each bus line
400
400
pF
Figure 3-5. I2C Interface Timing
12
ELECTRICAL SPECIFICATIONS
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
4 TYPICAL PERFORMANCE
TA = 25°C (unless otherwise noted)
4.1 DAC Performance
H
AMPLITUDE
AMPLITUDE
vs
vs
FREQUENCY
FREQUENCY
0
0
AVDD = HPVDD = 3.3 V
IOVDD = SPKVDD = 3.3 V
DVDD = 1.8 V
AVDD = HPVDD = 3.3 V
IOVDD = SPKVDD = 3.3 V
DVDD = 1.8 V
−20
−40
−20
−40
−60
−60
−80
−80
−100
−120
−140
−160
−100
−120
−140
−160
0
5
10
15
20
0
5
10
15
20
f − Frequency − kHz
f − Frequency − kHz
G001
G002
Figure 4-1. FFT - DAC to Line Output
TEXT ADDED FOR SPACING
Figure 4-2. FFT - DAC to Headphone Output
TEXT ADDED FOR SPACING
TOTAL HARMONIC DISTORTION + NOISE
vs
OUTPUT POWER
0
−10
−20
−30
−40
−50
−60
−70
−80
−90
−100
HPVDD = 2.7 V
CM = 1.35 V
HPVDD = 3 V
CM = 1.5 V
HPVDD = 3.3 V
CM = 1.65 V
HPVDD = 3.6 V
CM = 1.8 V
IOVDD = 3.3 V
DVDD = 1.8 V
Gain = 9 dB
R
L
= 16 Ω
0.00 0.02 0.04 0.06 0.08 0.10 0.12 0.14
P
O
− Output Power − W
G025
Figure 4-3. Headphone Output Power
Copyright © 2013, Texas Instruments Incorporated
TYPICAL PERFORMANCE
13
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
4.2 Class-D Speaker Driver Performance
H
TOTAL HARMONIC DISTORTION + NOISE
vs
TOTAL HARMONIC DISTORTION + NOISE
vs
OUTPUT POWER
OUTPUT POWER
0
0
−10
−20
−30
−40
−50
−60
−70
SPKVDD = 3.3 V
AVDD = HPVDD = 3.3 V
IOVDD = 3.3 V
SPKVDD = 5.5 V
DVDD = 1.8 V
−10
R
L
= 4 Ω
−20
−30
−40
−50
−60
−70
SPKVDD = 3.6 V
Driver Gain
= 24 dB
SPKVDD = 4.3 V
SPKVDD = 5.5 V
Driver Gain
= 18 dB
Driver Gain
= 12 dB
AVDD = 3.3 V
HPVDD = 3.3 V
IOVDD = 3.3 V
DVDD = 1.8 V
Driver Gain
= 6 dB
Driver Gain = 18 dB
R
L
= 4 Ω
0.0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
4.0
0.0
0.5
1.0
1.5
P − Output Power − W
O
2.0
2.5
3.0
3.5
4.0
P
O
− Output Power − W
G010
G011
Figure 4-4. Max Class-D Speaker-Driver Output Power (RL = 4 Ω)
Figure 4-5. Class-D Speaker-Driver Output Power (RL = 4 Ω)
TOTAL HARMONIC DISTORTION + NOISE
TOTAL HARMONIC DISTORTION + NOISE
vs
vs
OUTPUT POWER
OUTPUT POWER
0
0
SPKVDD = 3.3 V
AVDD = HPVDD = 3.3 V
IOVDD = 3.3 V
SPKVDD = 5.5 V
−10
−10
DVDD = 1.8 V
R
L
= 8 Ω
−20
−30
−40
−50
−60
−70
−20
SPKVDD = 3.6 V
Driver Gain
= 18 dB
−30
SPKVDD = 4.3 V
SPKVDD = 5.5 V
−40
Driver Gain
= 24 dB
Driver Gain
= 12 dB
AVDD = 3.3 V
HPVDD = 3.3 V
IOVDD = 3.3 V
DVDD = 1.8 V
−50
Driver Gain
= 6 dB
−60
Driver Gain = 18 dB
R
L
= 8 Ω
−70
0.0
0.0
0.5
1.0
1.5
2.0
2.5
0.5
1.0
1.5
2.0
2.5
3.0
P
O
− Output Power − W
P − Output Power − W
O
G012
G013
Figure 4-6. Max Class-D Speaker-Driver Output Power (RL = 8 Ω)
Figure 4-7. Class-D Speaker-Driver Output Power (RL = 8 Ω)
14
TYPICAL PERFORMANCE
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
4.3 Analog Bypass Performance
H
AMPLITUDE
AMPLITUDE
vs
vs
FREQUENCY
FREQUENCY
0
0
−20
AVDD = HPVDD = 3.3 V
IOVDD = SPKVDD = 3.3 V
DVDD = 1.8 V
AVDD = HPVDD = 3.3 V
IOVDD = SPKVDD = 3.3 V
DVDD = 1.8 V
−20
−40
−40
−60
−60
−80
−80
−100
−120
−140
−160
−100
−120
−140
−160
0
5
10
15
20
0
5
10
15
20
f − Frequency − kHz
f − Frequency − kHz
G008
G009
Figure 4-8. FFT - Line-In Bypass to Line Output
Figure 4-9. FFT - Line-In Bypass to Headphone Output
4.4 MICBIAS Performance
H
VOLTAGE
vs
CURRENT
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0.0
Micbias = AVDD (3.3 V)
Micbias = 2.5 V
Micbias = 2 V
0.0
0.5
1.0
1.5
I − Current − mA
Figure 4-10. MICBIAS
2.0
2.5
3.0
3.5
4.0
G016
Copyright © 2013, Texas Instruments Incorporated
TYPICAL PERFORMANCE
15
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
5 APPLICATION INFORMATION
5.1 Typical Circuit Configuration
3.3V AVDD
SVDD
0.1 mF
0.1 mF
0.1 mF
22 mF
0.1 mF
22 mF
10 mF
10 mF
IOVDD
Rp ´ 2
SPKVDD SPKVDD
SPKVSS SPKVSS
HPVDD AVDD
AVSS HPVSS
SDA
SCL
GPIO1
MCLK
SPKP
SPKP
SPKM
SPKM
8-W or 4-W
Speaker
WCLK
DIN
BCLK
RESET
To External
MIC Circuitry
MICBIAS
AIN1
Stereo
Headphone
Out
HPL
HPR
Analog In
AIN2
AVDD
34.8 kW
25 kW
VOL/MICDET
1 mF
9.76 kW
DVDD DVSS
IOVDD IOVSS
1.8V DVDD
0.1 mF
IOVDD
0.1 mF
AVSS
10 mF
10 mF
S0400-08
Figure 5-1. Typical Circuit Configuration
5.2 Overview
The TLV320DAC3100-Q1 is a highly integrated stereo audio DAC for portable computing, communication,
and entertainment applications. A register-based architecture eases integration with microprocessor-based
systems through standard serial-interface buses. This device supports the two-wire I2C bus interface
which provides full register access. All peripheral functions are controlled through these registers and the
onboard state machines.
The TLV320DAC3100-Q1 consists of the following blocks:
•
•
Stereo Audio DAC
Dynamic range compressor (DRC)
16
APPLICATION INFORMATION
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
•
•
•
•
•
•
•
•
Digital sine-wave generator for clicks and beeps
Stereo headphone and lineout amplifier
Class-D mono amplifier capable of driving 4-Ω speakers
Pin-controlled or register-controlled volume level
Power-down de-pop and power-up soft start
Analog inputs
I2C control interface
Power-down control block
Following a toggle of the RESET pin or a software reset, the device operates in the default mode. The I2C
interface is used to write to the control registers to configure the device.
The I2C address assigned to the TLV320DAC3100-Q1 is 001 1000. This device always operates in an I2C
slave mode. This device always operates in an I2C slave mode. All registers are 8-bit, and all writable
registers have read-back capability. The device auto-increments to support sequential addressing and can
be used with I2C fast mode. Once the device is reset, all appropriate registers are updated by the host
processor to configure the device as needed by the user.
5.2.1 Device Initialization
5.2.1.1 Power-Supply Sequence
The TLV320DAC3100-Q1 requires multiple power supply rails for operation. All the power rails must be
powered up for the device to operate at the fullest potention. The following is the recommended power-up
sequencing for proper operation:
1. Power up SPKVDD
2. Power up IOVDD
3. Power up DVDD shortly after IOVDD
4. Power up AVDD and HPVDD
Although not necessary, if the system requires, during shutdown, remove the power supplies in the
reverse order of the above sequence.
5.2.1.2 Reset
The TLV320DAC3100-Q1 internal logic must be initialized to a known condition for proper device function.
To initialize the device to its default operating condition, the hardware reset pin (RESET) must be pulled
low for at least 10 ns. For this initialization to work, both the IOVDD and DVDD supplies must be powered
up. TI recommends that while the DVDD supply powers up, the RESET pin is pulled low.
The device can also be reset via software reset. Writing a 1 into page 0 / register 1, bit D0 resets the
device.
5.2.1.3 Device Start-Up Lockout Times
After the TLV320DAC3100-Q1 is initialized through hardware reset at power up or software reset, the
internal memories are initialized to default values. This initialization takes place within 1 ms after pulling
the RESET signal high. During this initialization phase, no register-read or register-write operation should
be performed on DAC coefficient buffers. Also, no block within the codec should be powered up during the
initialization phase.
5.2.1.4 PLL Start-Up
Whenever the PLL is powered up, a start-up delay of approximately of 10 ms occurs after the power-up
command of the PLL and before the clocks are available to the codec. This delay is to ensure stable
operation of the PLL and clock-divider logic.
Copyright © 2013, Texas Instruments Incorporated
APPLICATION INFORMATION
17
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
5.2.1.5 Power-Stage Reset
The power-stage-only reset is used to reset the device after an overcurrent latching shutdown has
occurred. Using this reset re-enables the output stage without resetting all of the registers in the device.
Each of the four power stages has its own dedicated reset bit. The headphone power-stage reset is
performed by setting page 1 / register 31, bit D7 for HPL and by setting page 1 / register 31, bit D6 for
HPR. The speaker power-stage reset is performed by setting page 1 / register 32, bit D7 for SPKP and
SPKM.
5.2.1.6 Software Power Down
By default, all circuit blocks are powered down following a reset condition. Hardware power up of each
circuit block can be controlled by writing to the appropriate control register. This approach allows the
lowest power-supply current for the functionality required. However, when a block is powered down, all of
the register settings are maintained as long as power is still being applied to the device.
5.2.2 Audio Analog I/O
The TLV320DAC3100-Q1 has a stereo audio DAC. The device supports a wide range of analog interfaces
to support different headsets and analog outputs. The TLV320DAC3100-Q1 has features to interface
output drivers (8-Ω, 16-Ω, 32-Ω). A special circuit has also been included in the TLV320DAC3100-Q1 to
insert a short key-click sound into the stereo audio output. The key-click sound is used to provide
feedback to the user when a particular button is pressed or item is selected. The specific sound of the
keyclick can be adjusted by varying several register bits that control its frequency, duration, and amplitude
(see Section 5.5.7).
5.3 Digital Processing Low-Power Modes
The TLV320DAC3100-Q1 device can be tuned to minimize power dissipation, to maximize performance,
or to an operating point between the two extremes to best fit the application. The choice of processing
blocks, PRB_P1 to PRB_P25 for stereo playback, also influences the power consumption. In fact, the
numerous processing blocks have been implemented to offer a choice among configurations having a
different balance of power optimization and signal-processing capabilities.
5.3.1 DAC Playback on Headphones, Stereo, 48 kHz, DVDD = 1.8 V, AVDD = 3.3 V,
HPVDD = 3.3 V
DOSR = 128, Processing Block = PRB_P7 (Interpolation Filter B)
Power consumption = 24.28 mW
Table 5-1. PRB_P7 Alternative Processing Blocks, 24.28 mW
Processing Block
PRB_P1
Filter
A
Estimated Power Change (mW)
1.34
2.86
2.11
1.18
0.53
1.89
0.87
1.48
2.89
3.23
PRB_P2
A
PRB_P3
A
PRB_P8
B
PRB_P9
B
PRB_P10
PRB_P11
PRB_P23
PRB_P24
PRB_P25
B
B
A
A
A
18
APPLICATION INFORMATION
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
DOSR = 64, Processing Block = PRB_P7 (Interpolation Filter B)
Power consumption = 24.5 mW
Table 5-2. PRB_P7 Alternative Processing Blocks, 24.5 mW
Processing Block
PRB_P1
Filter
A
Estimated Power Change (mW)
1.17
2.62
2
PRB_P2
A
PRB_P3
A
PRB_P8
B
0.99
0.5
PRB_P9
B
PRB_P10
PRB_P11
PRB_P23
PRB_P24
PRB_P25
B
1.46
0.66
1.43
2.69
2.92
B
A
A
A
5.3.2 DAC Playback on Headphones, Mono, 48 kHz, DVDD = 1.8 V, AVDD = 3.3 V,
HPVDD = 3.3 V
DOSR = 128, Processing Block = PRB_P12 (Interpolation Filter B)
Power consumption = 15.4 mW
Table 5-3. PRB_P12 Alternative Processing Blocks, 15.4 mW
Processing Block
PRB_P4
Filter
Estimated Power Change (mW)
A
A
A
B
B
B
B
0.57
1.48
1.08
0.56
0.27
0.89
0.31
PRB_P5
PRB_P6
PRB_P13
PRB_P14
PRB_P15
PRB_P16
DOSR = 64, Processing Block = PRB_P12 (Interpolation Filter B)
Power consumption = 15.54 mW
Table 5-4. PRB_P12 Alternative Processing Blocks, 15.54 mW
Processing Block
Filter
Estimated Power Change (mW)
PRB_P4
PRB_P5
PRB_P6
PRB_P13
PRB_P14
PRB_P15
PRB_P16
A
A
A
B
B
B
B
0.37
1.23
1.15
0.43
0.13
0.85
0.21
5.3.3 DAC Playback on Headphones, Stereo, 8 kHz, DVDD = 1.8 V, AVDD = 3.3 V,
HPVDD = 3.3 V
DOSR = 768, Processing Block = PRB_P7 (Interpolation Filter B)
Power consumption = 22.44 mW
Copyright © 2013, Texas Instruments Incorporated
APPLICATION INFORMATION
19
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
Table 5-5. PRB_P7 Alternative Processing Blocks, 22.44 mW
Processing Block
PRB_P1
Filter
A
Estimated Power Change (mW)
0.02
0.31
0.23
0.28
–0.03
0.14
0.05
0.29
0.26
0.47
PRB_P2
A
PRB_P3
A
PRB_P8
B
PRB_P9
B
PRB_P10
PRB_P11
PRB_P23
PRB_P24
PRB_P25
B
B
A
A
A
DOSR = 384, Processing Block = PRB_P7 (Interpolation Filter B)
Power consumption = 22.83 mW
Table 5-6. PRB_P7 Alternative Processing Blocks, 22.83 mW
Processing Block
PRB_P1
Filter
A
Estimated Power Change (mW)
0.27
0.4
PRB_P2
A
PRB_P3
A
0.34
0.2
PRB_P8
B
PRB_P9
B
0.08
0.24
0.12
0.23
0.42
0.46
PRB_P10
PRB_P11
PRB_P23
PRB_P24
PRB_P25
B
B
A
A
A
5.3.4 DAC Playback on Headphones, Mono, 8 kHz, DVDD = 1.8 V, AVDD = 3.3 V,
HPVDD = 3.3 V
DOSR = 768, Processing Block = PRB_P12 (Interpolation Filter B)
Power consumption = 14.49 mW
Table 5-7. PRB_P12 Alternative Processing Blocks, 14.49 mW
Processing Block
PRB_P4
Filter
Estimated Power Change (mW)
A
A
A
B
B
B
B
–0.04
0.2
PRB_P5
PRB_P6
–0.01
0.1
PRB_P13
PRB_P14
PRB_P15
PRB_P16
0.05
–0.03
0.07
20
APPLICATION INFORMATION
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
DOSR = 384, Processing Block = PRB_P12 (Interpolation Filter B)
Power consumption = 14.42 mW
Table 5-8. PRB_P12 Alternative Processing Blocks, 14.42 mW
Processing Block
PRB_P4
Filter
Estimated Power Change (mW)
A
A
A
B
B
B
B
0.16
0.3
PRB_P5
PRB_P6
0.2
PRB_P13
PRB_P14
PRB_P15
PRB_P16
0.15
0.07
0.18
0.09
5.3.5 DAC Playback on Headphones, Stereo, 192 kHz, DVDD = 1.8 V, AVDD = 3.3 V,
HPVDD = 3.3 V
DOSR = 32, Processing Block = PRB_P17 (Interpolation Filter C)
Power consumption = 27.05 mW
Table 5-9. PRB_P17 Alternative Processing Blocks, 27.05 mW
Processing Block
PRB_P18
Filter
C
Estimated Power Change (mW)
5.28
1.98
PRB_P19
C
5.3.6 DAC Playback on Line Out (10 k-Ω load), Stereo, 48 kHz, DVDD = 1.8 V, AVDD = 3 V,
HPVDD = 3 V
DOSR = 64, Processing Block = PRB_P7 (Interpolation Filter B)
Power consumption = 12.85 mW
5.4 Analog Signals
The TLV320DAC3100-Q1 analog signals consist of:
•
•
•
Microphone bias (MICBIAS)
Analog inputs AIN1 and AIN2
Analog outputs, class-D speaker driver and headphone and lineout driver, providing output capability
for the DAC, AIN1, AIN2 or a mix of the three
5.4.1 MICBIAS
The TLV320DAC3100-Q1 includes a microphone bias circuit which can source up to 4 mA of current and
is programmable to a 2-V, 2.5-V, or AVDD level. The level can be controlled by writing to page 1 /
register 46, bits D1–D0. This functionality is shown in Table 5-10.
Table 5-10. MICBIAS Settings
D1
0
D0
0
FUNCTIONALITY
MICBIAS output is powered down.
MICBIAS output is powered to 2 V.
MICBIAS output is powered to 2.5 V.
MICBIAS output is powered to AVDD.
0
1
1
0
1
1
Copyright © 2013, Texas Instruments Incorporated
APPLICATION INFORMATION
21
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
During normal operation, MICBIAS can be set to 2.5 V for better performance. However, depending on the
model of microphone that is selected, optimal performance might be obtained at another setting, so the
performance at a given setting should be verified.
The lowest current consumption occurs when MICBIAS is powered down. The next-lowest current
consumption occurs when MICBIAS is set at AVDD. The highest current consumption occurs when
MICBIAS is set at 2 V.
5.4.2 Analog Inputs AIN1 and AIN2
AIN1 (pin 13) and AIN2 (pin 14) are inputs to the output mixer along with the DAC output. Page 1 /
register 35 provides control signals for determining the signals routed through the output mixer. The output
of the output mixer then can be attenuated or gained through the class-D and, or, headphone and lineout
drivers.
5.5 Audio DAC and Audio Analog Outputs
Each channel of the stereo audio DAC consists of a digital audio processing block, a digital interpolation
filter, a digital delta-sigma modulator, and an analog reconstruction filter. This high oversampling ratio
(typically DOSR is between 32 and 128) exhibits good dynamic range by ensuring that the quantization
noise generated within the delta-sigma modulator stays outside of the audio frequency band. Audio analog
outputs include stereo headphone, or lineouts, and stereo class-D speaker outputs.
5.5.1 DAC
The TLV320DAC3100-Q1 stereo audio DAC supports data rates from 8 kHz to 192 kHz. Each channel of
the stereo audio DAC consists of a signal-processing engine with fixed processing blocks, a digital
interpolation filter, a multibit digital delta-sigma modulator, and an analog reconstruction filter. The DAC is
designed to provide enhanced performance at low sampling rates through increased oversampling and
image filtering, thereby keeping quantization noise generated within the delta-sigma modulator and signal
images strongly suppressed within the audio band to beyond 20 kHz. To handle multiple input rates and
optimize power dissipation and performance, the TLV320DAC3100-Q1 allows the system designer to
program the oversampling rates over a wide range from 1 to 1024 by configuring page 0 / register 13 and
page 0 / register 14. The system designer can choose higher oversampling ratios for lower input data
rates and lower oversampling ratios for higher input data rates.
The TLV320DAC3100-Q1 DAC channel includes a built-in digital interpolation filter to generate
oversampled data for the delta-sigma modulator. The interpolation filter can be chosen from three different
types, depending on required frequency response, group delay, and sampling rate.
DAC power up is controlled by writing to page 0 / register 63, bit D7 for the left channel and bit D6 for the
right channel. The left-channel DAC clipping flag is provided as a read-only bit on page 0 / register 39, bit
D7. The right-channel DAC clipping flag is provided as a read-only bit on page 0 / register 39, bit D6
5.5.1.1 DAC Processing Blocks
The TLV320DAC3100-Q1 implements signal-processing capabilities and interpolation filtering via
processing blocks. These fixed processing blocks give users the choice of how much and what type of
signal processing they use and which interpolation filter is applied.
The choices among these processing blocks allow the system designer to balance power conservation
and signal-processing flexibility. Table 5-11 gives an overview of all available processing blocks of the
DAC channel and their properties. The resource-class column gives an approximate indication of power
consumption for the digital (DVDD) supply; however, based on the out-of-band noise spectrum, the analog
power consumption of the drivers (HPVDD) may differ.
The signal processing blocks available are:
•
•
First-order IIR
Scalable number of biquad filters
22
APPLICATION INFORMATION
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
•
•
3D effect
Digital sine-wave (beep) generator
The processing blocks are tuned for common cases and can achieve high image rejection or low group
delay in combination with various signal-processing effects such as audio effects and frequency shaping.
The available first-order IIR and biquad filters have fully user-programmable coefficients.
Table 5-11. Overview – DAC Predefined Processing Blocks
Number
Processing
Block No.
Interpolation
Filter
First-Order
IIR Available
Beep
Generator
Resource
Class
Channel
of
DRC
3D
Biquads
PRB_P1
PRB_P2
PRB_P3
PRB_P4
PRB_P5
PRB_P6
PRB_P7
PRB_P8
PRB_P9
PRB_P10
PRB_P11
PRB_P12
PRB_P13
PRB_P14
PRB_P15
PRB_P16
PRB_P17
PRB_P18
PRB_P19
PRB_P20
PRB_P21
PRB_P22
PRB_P23
PRB_P24
PRB_P25
A
A
A
A
A
A
B
B
B
B
B
B
B
B
B
B
C
C
C
C
C
C
A
A
A
Stereo
Stereo
Stereo
Left
No
Yes
Yes
No
3
6
6
3
6
6
0
4
4
6
6
0
4
4
6
6
0
4
4
0
4
4
2
5
5
No
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Yes
Yes
Yes
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
No
Yes
8
12
10
4
No
Left
Yes
Yes
Yes
No
Yes
No
6
Left
6
Stereo
Stereo
Stereo
Stereo
Stereo
Left
No
6
Yes
No
8
No
8
Yes
Yes
Yes
No
Yes
No
10
8
No
3
Left
Yes
No
4
Left
No
4
Left
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
No
6
Left
4
Stereo
Stereo
Stereo
Left
No
3
Yes
No
6
4
No
2
Left
Yes
No
3
Left
2
Stereo
Stereo
Stereo
No
8
Yes
Yes
Yes
Yes
12
12
5.5.1.2 DAC Processing Blocks – Details
5.5.1.2.1 Three Biquads, Interpolation Filter A
BiQuad
A
from
Interface
BiQuad
B
BiQuad
C
Interp.
Filter A
´
to
Modulator
Digital
Volume
Ctrl
Figure 5-2. Signal Chain for PRB_P1 and PRB_P4
Copyright © 2013, Texas Instruments Incorporated
APPLICATION INFORMATION
23
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
5.5.1.2.2 Six Biquads, First-Order IIR, DRC, Interpolation Filter A or B
Interp.
Filter
A or B
BiQuad
A
BiQuad
B
BiQuad
C
BiQuad
D
BiQuad
E
BiQuad
F
IIR
to
HPF
*
modulator
from
interface
Digital
Volume
Ctrl
DRC
Figure 5-3. Signal Chain for PRB_P2, PRB_P5, PRB_P10, and PRB_P15
5.5.1.2.3 Six Biquads, First-Order IIR, Interpolation Filter A or B
Interp.
Filter
A,B
BiQuad
A
BiQuad
B
BiQuad
C
BiQuad
D
BiQuad
E
BiQuad
F
to
Modulator
´
IIR
from
Interface
Digital
Volume
Ctrl
Figure 5-4. Signal Chain for PRB_P3, PRB_P6, PRB_P11, and PRB_P16
5.5.1.2.4 IIR, Interpolation Filter B or C
Interp.
Filter
B,C
´
to
Modulator
IIR
from
Interface
Digital
Volume
Ctrl
Figure 5-5. Signal Chain for PRB_P7, PRB_P12, PRB_P17, and PRB_P20
5.5.1.2.5 Four Biquads, DRC, Interpolation Filter B
BiQuad
A
BiQuad
B
BiQuad
C
BiQuad
D
Interp.
Filter B
to
modulator
HPF
*
from
interface
Digital
Volume
Ctrl
DRC
Figure 5-6. Signal Chain for PRB_P8 and PRB_P13
5.5.1.2.6 Four Biquads, Interpolation Filter B
BiQuad
A
from
Interface
BiQuad
B
BiQuad
C
BiQuad
D
Interp.
Filter B
´
to
Modulator
Digital
Volume
Ctrl
Figure 5-7. Signal Chain for PRB_P9 and PRB_P14
24
APPLICATION INFORMATION
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
5.5.1.2.7 Four Biquads, First-Order IIR, DRC, Interpolation Filter C
BiQuad
A
BiQuad
B
BiQuad
C
BiQuad
D
Interp.
Filter C
IIR
to
HPF
*
modulator
from
interface
Digital
Volume
DRC
Ctrl
Figure 5-8. Signal Chain for PRB_P18 and PRB_P21
5.5.1.2.8 Four Biquads, First-Order IIR, Interpolation Filter C
BiQuad
A
BiQuad
B
BiQuad
C
BiQuad
D
Interp.
Filter C
´
IIR
to
modulator
from
Interface
Digital
Volume
Ctrl
Figure 5-9. Signal Chain for PRB_P19 and PRB_P22
5.5.1.2.9 Two Biquads, 3D, Interpolation Filter A
From
+
Biquad
BL
Biquad
CL
Left-
Channel
Interface
Interp.
Filter A
+
+
´
To
Modulator
Digital
Volume
Ctrl
+
–
Biquad
AL
Biquad
AR
3D
PGA
+
+
+
From
Right-
Channel
Interface
–
Biquad
BR
Biquad
CR
Interp.
Filter A
´
To
Modulator
Digital
Volume
Ctrl
Figure 5-10. Signal Chain for PRB_P23
Copyright © 2013, Texas Instruments Incorporated
APPLICATION INFORMATION
25
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
5.5.1.2.10 Five Biquads, DRC, 3D, Interpolation Filter A
IIR
left
+
BiQuad
BL
BiQuad
CL
BiQuad
DL
BiQuad
EL
BiQuad
FL
Interp.
Filter A
to
+
*
HPF
modulator
from
left
+
channel
interface
Digital
Volume
Ctrl
DRC
+
-
BiQuad
AL
BiQuad
AR
3D
PGA
+
-
+
IIR
right
BiQuad
BR
BiQuad
CR
BiQuad
DR
BiQuad
ER
BiQuad
FR
Interp.
Filter A
to
+
*
HPF
modulator
from
right
channel
interface
Digital
Volume
Ctrl
DRC
Figure 5-11. Signal Chain for PRB_P24
5.5.1.2.11 Five Biquads, DRC, 3D, Beep Generator, Interpolation Filter A
IIR
left
+
BiQuad
BL
BiQuad
CL
BiQuad
DL
BiQuad
EL
BiQuad
FL
Interp.
Filter A
+
to
+
HPF
*
from
left
modulator
+
channel
interface
DRC
Digital
Volume
Ctrl
+
-
BiQuad
AL
BiQuad
AR
3D
PGA
+
*
Beep
Volume
Ctrl
Beep
Gen.
*
-
IIR
right
+
BiQuad
BR
BiQuad
CR
BiQuad
DR
BiQuad
ER
BiQuad
FR
Interp.
Filter A
+
to
+
*
HPF
modulator
from
right
channel
interface
Digital
Volume
Ctrl
DRC
Figure 5-12. Signal Chain for PRB_P25
5.5.1.3 DAC User-Programmable Filters
Depending on the selected processing block, different types and orders of digital filtering are available. Up
to six biquad sections are available for specific processing blocks.
The coefficients of the available filters are arranged as sequentially-indexed coefficients in two banks. If
adaptive filtering is chosen, the coefficient banks can be switched in real time.
26
APPLICATION INFORMATION
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
When the DAC is running, the user-programmable filter coefficients are locked and cannot be accessed
for either read or write.
However, the TLV320DAC3100-Q1 offers an adaptive filter mode as well. Setting page 8 / register 1, bit
D2 = 1 turns on double buffering of the coefficients. In this mode, filter coefficients can be updated through
the host and activated without stopping and restarting the DAC. This enables advanced adaptive filtering
applications.
In the double-buffering scheme, all coefficients are stored in two buffers (buffers A and B). When the DAC
is running and the adaptive filtering mode is turned on, setting page 8 / register 1, bit D0 = 1 switches the
coefficient buffers at the next start of a sampling period. This bit is set back to 0 after the switch occurs. At
the same time, page 8 / register 1, bit D1 toggles.
The flag in page 8 / register 1, bit D1 indicates which of the two buffers is actually in use.
Page 8 / register 1, bit D1 = 0: buffer A is in use by the DAC engine; bit D1 = 1: buffer B is in use.
While the device is running, coefficient updates are always made to the buffer not in use by the DAC,
regardless of the buffer to which the coefficients have been written.
Table 5-12. Adaptive-Mode Filter-Coefficient Buffer Switching
DAC Powered Up
Page 8, Reg 1, Bit D1
Coefficient Buffer in Use
None
Writing to
Buffer A
Updates
Buffer A
No
No
0
0
0
0
1
1
None
Buffer B
Buffer A
Buffer B
Buffer A
Buffer B
Buffer B
Buffer B
Buffer B
Buffer A
Buffer A
Yes
Yes
Yes
Yes
Buffer A
Buffer A
Buffer B
Buffer B
The user-programmable coefficients for the DAC processing blocks are defined on page 8 and page 9 for
buffer A and page 12 and page 13 for buffer B.
The coefficients of these filters are each 16-bit, 2s-complement format, occupying two consecutive 8-bit
registers in the register space. Specifically, the filter coefficients are in 1.15 (one dot 15) format with a
range from –1.0 (0x8000) to 0.999969482421875 (0x7FFF) as shown in Figure 5-13.
2–15 Bit
2–4 Bit
2–1 Bit
Largest Positive Number:
= 0.111111111111111111
= 0.999969482421875 = 1.0 – 1 LSB
Largest Negative Number:
= 1.000010000100001000
= 0x8000 = –1.0 (by definition)
Fraction
Point
Sign Bit
S...xxxxxxxxxxxxxxxxxx
Figure 5-13. 1.15 2s-Complement Coefficient Format
5.5.1.3.1 First-Order IIR Section
The IIR is of first order and its transfer function is given by Equation 1.
N0 + N1z-1
215 - D1z-1
H(z) =
(1)
27
The frequency response for the first-order IIR section with default coefficients is flat.
Copyright © 2013, Texas Instruments Incorporated
APPLICATION INFORMATION
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
Table 5-13. DAC IIR Filter Coefficients
Filter
Coefficient
Left DAC Channel
Right DAC Channel
Default (Reset) Value
First-order IIR
N0
Page 9 / register 2 and page 9 /
register 3
Page 9 / register 8 and page 9 /
register 9
0x7FFF (decimal 1.0 –
LSB value)
N1
D1
Page 9 / register 4 and page 9 /
register 5
Page 9 / register 10 and page 9 /
register 11
0x0000
Page 9 / register 6 and page 9 /
register 7
Page 9 / register 12 and page 9 /
register 13
0x0000
5.5.1.3.2 Biquad Section
The transfer function of each of the biquad filters is given by Equation 2.
N0 + 2´N1z-1 + N2z-2
215 - 2´D1z-1 - D2z-2
H(z) =
(2)
Table 5-14. DAC Biquad Filter Coefficients
Filter
Coefficient
Left DAC Channel
Right DAC Channel
Default (Reset) Value
Biquad A
N0
Page 8 / register 2 and page 8 /
register 3
Page 8 / register 66 and page 8 /
register 67
0x7FFF (decimal 1.0 –
LSB value)
N1
N2
D1
D2
N0
N1
N2
D1
D2
N0
N1
N2
D1
D2
Page 8 / register 4 and page 8 /
register 5
Page 8 / register 68 and page 8 /
register 69
0x0000
0x0000
0x0000
0x0000
Page 8 / register 6 and page 8 /
register 7
Page 8 / register 70 and page 8 /
register 71
Page 8 / register 8 and page 8 /
register 9
Page 8 / register 72 and page 8 /
register 73
Page 8 / register 10 and page 8 /
register 11
Page 8 / register 74 and page 8 /
register 75
Biquad B
Page 8 / register 12 and page 8 /
register 13
Page 8 / register 76 and page 8 /
register 77
0x7FFF (decimal 1.0 –
LSB value)
Page 8 / register 14 and page 8 /
register 15
Page 8 / register 78 and page 8 /
register 79
0x0000
0x0000
0x0000
0x0000
Page 8 / register 16 and page 8 /
register 17
Page 8 / register 80 and page 8 /
register 81
Page 8 / register 18 and page 8 /
register 19
Page 8 / register 82 and page 8 /
register 83
Page 8 / register 20 and page 8 /
register 21
Page 8 / register 84 and page 8 /
register 85
Biquad C
Page 8 / register 22 and page 8 /
register 23
Page 8 / register 86 and page 8 /
register 87
0x7FFF (decimal 1.0 –
LSB value)
Page 8 / register 24 and page 8 /
register 25
Page 8 / register 88 and page 8 /
register 89
0x0000
0x0000
0x0000
0x0000
Page 8 / register 26 and page 8 /
register 27
Page 8 / register 90 and page 8 /
register 91
Page 8 / register 28 and page 8 /
register 29
Page 8 / register 92 and page 8 /
register 93
Page 8 / register 30 and page 8 /
register 31
Page 8 / register 94 and page 8 /
register 95
28
APPLICATION INFORMATION
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
Table 5-14. DAC Biquad Filter Coefficients (continued)
Filter
Coefficient
Left DAC Channel
Right DAC Channel
Default (Reset) Value
Biquad D
N0
Page 8 / register 32 and page 8 /
register 33
Page 8 / register 96 and page 8 /
register 97
0x7FFF (decimal 1.0 –
LSB value)
N1
N2
D1
D2
N0
N1
N2
D1
D2
N0
N1
N2
D1
D2
Page 8 / register 34 and page 8 /
register 35
Page 8 / register 98 and page 8 /
register 99
0x0000
0x0000
0x0000
0x0000
Page 8 / register 36 and page 8 /
register 37
Page 8 / register 100 and page 8 /
register 101
Page 8 / register 38 and page 8 /
register 39
Page 8 / register 102 and page 8 /
register 103
Page 8 / register 40 and page 8 /
register 41
Page 8 / register 104 and page 8 /
register 105
Biquad E
Page 8 / register 42 and page 8 /
register 43
Page 8 / register 106 and page 8 /
register 107
0x7FFF (decimal 1.0 –
LSB value)
Page 8 / register 44 and page 8 /
register 45
Page 8 / register 108 and page 8 /
register 109
0x0000
0x0000
0x0000
0x0000
Page 8 / register 46 and page 8 /
register 47
Page 8 / register 110 and page 8 /
register 111
Page 8 / register 48 and page 8 /
register 49
Page 8 / register 112 and page 8 /
register 113
Page 8 / register 50 and page 8 /
register 51
Page 8 / register 114 and page 8 /
register 115
Biquad F
Page 8 / register 52 and page 8 /
register 53
Page 8 / register 116 and page 8 /
register 117
0x7FFF (decimal 1.0 –
LSB value)
Page 8 / register 54 and page 8 /
register 55
Page 8 / register 118 and page 8 /
register 119
0x0000
0x0000
0x0000
0x0000
Page 8 / register 56 and page 8 /
register 57
Page 8 / register 120 and page 8 /
register 121
Page 8 / register 58 and page 8 /
register 59
Page 8 / register 122 and page 8 /
register 123
Page 8 / register 60 and page 8 /
register 61
Page 8 / register 124 and page 8 /
register 125
5.5.1.4 DAC Interpolation Filter Characteristics
5.5.1.4.1 Interpolation Filter A
Filter A is designed for an fS up to 48 ksps with a flat passband of 0 to 20 kHz.
Table 5-15. Specification for DAC Interpolation Filter A
Parameter
Condition
Value (Typical)
±0.015
Units
dB
Filter-gain pass band
Filter-gain stop band
Filter group delay
0 … 0.45 fS
0.55… 7.455 fS
–65
dB
21 / fS
s
Copyright © 2013, Texas Instruments Incorporated
APPLICATION INFORMATION
29
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
DAC Channel Response for Interpolation Filter A
(Red line corresponds to –65 dB)
0
–10
–20
–30
–40
–50
–60
–70
–80
–90
1
2
3
4
5
6
7
Frequency Normalized to fS
G016
Figure 5-14. Frequency Response of DAC Interpolation Filter A
5.5.1.4.2 Interpolation Filter B
Filter B is specifically designed for an fS of up to 96 ksps. Thus, the flat passband region easily covers the
required audio band of 0 to 20 kHz.
Table 5-16. Specification for DAC Interpolation Filter B
Parameter
Condition
Value (Typical)
±0.015
Units
dB
Filter-gain pass band
Filter-gain stop band
Filter group delay
0 … 0.45 fS
0.55… 3.45 fS
–58
dB
18 / fS
s
DAC Channel Response for Interpolation Filter B
(Red line corresponds to –58 dB)
0
–10
–20
–30
–40
–50
–60
–70
–80
0.5
1.0
1.5
2.0
2.5
3.0
3.5
Frequency Normalized to fS
G017
Figure 5-15. Frequency Response of Channel Interpolation Filter B
30
APPLICATION INFORMATION
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
5.5.1.4.3 Interpolation Filter C
Filter C is specifically designed for the 192-ksps mode. The pass band extends up to 0.4 × fS
(corresponds to 80 kHz), more than sufficient for audio applications.
Table 5-17. Specification for DAC Interpolation Filter C
Parameter
Condition
0 … 0.35 fS
0.6… 1.4 fS
Value (Typical)
±0.03
Units
dB
Filter-gain pass band
Filter-gain stop band
Filter group delay
–43
dB
13 / fS
s
DAC Channel Response for Interpolation Filter C
(Red line corresponds to –43 dB)
0
–10
–20
–30
–40
–50
–60
–70
0.0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
Frequency Normalized to fS
G018
Figure 5-16. Frequency Response of DAC Interpolation Filter C
5.5.2 DAC Digital-Volume Control
The DAC has a digital-volume control block which implements programmable gain. Each channel has an
independent volume control that can be varied from 24 dB to –63.5 dB in 0.5-dB steps. The left-channel
DAC volume can be controlled by writing to page 0 / register 65, bits D7–D0. The right-channel DAC
volume can be controlled by writing to page 0 / register 66, bits D7–D0. DAC muting and setting up a
master gain control to control both channels is done by writing to page 0 / register 64, bits D3–D0. The
gain is implemented with a soft-stepping algorithm, which only changes the actual volume by 0.125 dB per
input sample, either up or down, until the desired volume is reached. The rate of soft-stepping can be
slowed to one step per two input samples by writing to page 0 / register 63, bits D1–D0. Note that the
default source for volume-control level settings is control by register writes (page 0 / register 65 and
page 0 / register 66 to control volume). Use of the VOL/MICDET pin to control the DAC volume is ignored
until the volume control source selected has been changed to pin control (page 0 / register 116, bit
D7 = 1). This functionality is shown in Figure 1-1.
During soft-stepping, the host does not receive a signal when the DAC has been completely muted. This
may be important if the host must mute the DAC before making a significant change, such as changing
sample rates. In order to help with this situation, the device provides a flag back to the host via a read-
only register, page 0 / register 38, bit D4 for the left channel and bit D0 for the right channel. This
information alerts the host when the part has completed the soft-stepping and the actual volume has
reached the desired volume level. The soft-stepping feature can be disabled by writing to page 0 /
register 63, bits D1–D0.
Copyright © 2013, Texas Instruments Incorporated
APPLICATION INFORMATION
31
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
If soft-stepping is enabled, the CODEC_CLKIN signal should be kept active until the DAC power-up flag is
cleared. When this flag is cleared, the internal DAC soft-stepping process is complete, and
CODEC_CLKIN can be stopped if desired. (The analog volume control can be ramped down using an
internal oscillator.)
5.5.3 Volume Control Pin
The volume-control pin is not enabled by default but it can be enabled by writing 1 to page 0 /
register 116, bit D7. The default DAC volume control uses software control of the volume, which occurs if
page 0 / register 116, bit D7 = 0. Soft-stepping the volume level is set up by writing to page 0 / register 63,
bits D1–D0.
When the volume-pin function is used, a 7-bit Vol ADC reads the voltage on the VOL/MICDET pin and
updates the digital volume control. (It overwrites the current value of the volume control.) The new volume
setting which has been applied due to a change of voltage on the volume control pin can be read on
page 0 / register 117, bits D6–D0. The 7-bit Vol ADC clock source can be selected on page 0 /
register 116, bit D6. The update rate can be programmed on page 0 / register 116, bits D2–D0 for this 7-
bit SAR ADC.
The VOL/MICDET pin gainmapping is shown in Table 5-18.
Table 5-18. VOL/MICDET Pin Gain Mapping
VOL/MICDET PIN SAR OUTPUT
DIGITAL GAIN APPLIED
0
1
18 dB
17.5 dB
17 dB
:
2
:
35
36
37
:
0.5 dB
0.0 dB
–0.5 dB
:
89
90
91
:
–26.5 dB
–27 dB
–28 dB
:
125
126
127
–62 dB
–63 dB
Mute
32
APPLICATION INFORMATION
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
The VOL/MICDET pin connection and functionality are shown in Figure 5-17.
24 dB to Mute
Digital
Programmable
DSP
DAC_L
D-S
DAC
Vol
Ctl
Engine
24 dB to Mute
AVDD
Digital
Programmable
DSP
VREF
IN
DAC_R
AVDD
D-S
DAC
Vol
Ctl
R1
P1
R2
Engine
VOL/
MICDET
18 dB to Mute
7- Bit ADC
CVOL
Tone Generator and Mixer Are
NOT Shown
24 dB to Mute
Volume Level
Register Controlled
AVSS
B0210-05
Figure 5-17. Digital Volume Controls for Beep Generator and DAC Play Data
As shown in Table 5-18, the VOL/MICDET pin has a range of volume control from 18 dB down to –63 dB,
and mute. However, if less maximum gain is required, then a smaller range of voltage should be applied
to the VOL/MICDET pin. This can be done by increasing the value of R2 relative to the value of (P1 + R1),
so that more voltage is available at the bottom of P1. The circuit should also be designed such that for the
values of R1, R2, and P1 chosen, the maximum voltage (top of the potentiometer) does not exceed
AVDD/2 (see Figure 5-17). The recommended values for R1, R2, and P1 for several maximum gains are
shown in Table 5-19.
Table 5-19. VOL/MICDET Pin Gain Scaling
ADC VOLTAGE
for AVDD = 3.3 V
(V)
R1
(kΩ)
P1
(kΩ)
R2
(kΩ)
DIGITAL GAIN RANGE
(dB)
25
33
25
25
25
0
0 to 1.65
18 to –63
3 to –63
0 to –63
7.68
9.76
0.386 to 1.642
0.463 to 1.649
34.8
5.5.4 Dynamic Range Compression
Typical music signals are characterized by crest factors, the ratio of peak signal power to average signal
power, of 12 dB or more. To avoid audible distortions due to clipping of peak signals, the gain of the DAC
channel must be adjusted so as not to cause hard clipping of peak signals. As a result, during nominal
periods, the applied gain is low, causing the perception that the signal is not loud enough. To overcome
this problem, dynamic range conpression (DRC) in the TLV320DAC3100-Q1 continuously monitors the
output of the DAC digital volume control to detect its power level relative to 0 dBFS. When the power level
is low, DRC increases the input signal gain to make it sound louder. At the same time, if a peaking signal
is detected, it autonomously reduces the applied gain to avoid hard clipping. This results in sounds more
pleasing to the ear as well as sounding louder during nominal periods.
The DRC functionality in the TLV320DAC3100-Q1 is implemented by a combination of processing blocks
in the DAC channel as described in Section 5.5.1.2.
DRC can be disabled by writing to page 0 / register 68, bits D6–D5.
Copyright © 2013, Texas Instruments Incorporated
APPLICATION INFORMATION
33
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
DRC typically works on the filtered version of the input signal. The input signals have no audio information
at dc and extremely low frequencies; however, they can significantly influence the energy estimation
function in the dynamic range compressor (the DRC). Also, most of the information about signal energy is
concentrated in the low-frequency region of the input signal.
To estimate the energy of the input signal, the signal is first fed to the DRC high-pass filter and then to the
DRC low-pass filter. These filters are implemented as first-order IIR filters given by
N0 + N1z-1
215 - D1z-1
HHPF(z) =
(3)
N0 + N1z-1
HLPF(z) =
215 - D1z-1
(4)
The coefficients for these filters are 16 bits wide in 2s-complement format and are user-programmable
through register write as given in Table 5-20.
Table 5-20. The DRC HPF and LPF Coefficients
Coefficient
HPF N0
Location
C71 page 9 / register 14 and page 9 / register 15
C72 page 9 / registers 16 and page 9 / register 17
C73 page 9 / registers 18 and page 9 / register 19
C74 page 9 / registers 20 and page 9 / register 21
C75 page 9 / registers 22 and page 9 / register 23
C76 page 9 / registers 24 and page 9 / register 25
HPF N1
HPF D1
LPF N0
LPF N1
LPF D1
The default values of these coefficients implement a high-pass filter with a cutoff at 0.000083 × DAC_fS,
and a low-pass filter with a cutoff at 0.000165 × DAC_fS.
The output of the DRC high-pass filter is fed to the processing block selected for the DAC channel. The
absolute value of the DRC LPF filter is used for energy estimation within the DRC.
The gain in the DAC digital volume control is controlled by page 0 / register 65 and page 0 / register 66.
When the DRC is enabled, the applied gain is a function of the digital volume control register setting and
the output of the DRC.
The DRC parameters are described in sections that follow.
5.5.4.1 DRC Threshold
DRC threshold represents the level of the DAC playback signal at which the gain compression becomes
active. The output of the digital volume control in the DAC is compared with the set threshold. The
threshold value is programmable by writing to page 0 / register 68, bits D4–D2. The threshold value can
be adjusted between –3 dBFS and –24 dBFS in steps of 3 dB. Keeping the DRC threshold value too high
may not leave enough time for the DRC block to detect peaking signals, and can cause excessive
distortion at the outputs. Keeping the DRC threshold value too low can limit the perceived loudness of the
output signal.
The recommended DRC threshold value is –24 dB.
When the output signal exceeds the set DRC threshold, the interrupt flag bits at page 0 / register 44,
bits D3–D2 are updated. These flag bits are sticky in nature, and are reset only after they are read back
by the user. The non-sticky versions of the interrupt flags are also available at page 0 / register 46,
bits D3–D2.
34
APPLICATION INFORMATION
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
5.5.4.2 DRC Hysteresis
DRC hysteresis is programmable by writing to page 0 / register 68, bits D1–D0. These bits can be
programmed to represent values between 0 dB and 3 dB in steps of 1dB. DRC hysteresis provides a
programmable window around the programmed DRC threshold that must be exceeded for the disabled
DRC to become enabled, or the enabled DRC to become disabled. For example, if the DRC threshold is
set to –12 dBFS and the DRC hysteresis is set to 3 dB, then if the gain compression in the DRC is
inactive, the output of the DAC digital volume control must exceed –9 dBFS before gain compression due
to the DRC is activated. Similarly, when the gain compression in the DRC is active, the output of the DAC
digital volume control must fall below –15 dBFS for gain compression in the DRC to be deactivated. The
DRC hysteresis feature prevents the rapid activation and de-activation of gain compression in the DRC in
cases when the output of the DAC digital volume control rapidly fluctuates in a narrow region around the
programmed DRC threshold. By programming the DRC hysteresis as 0 dB, the hysteresis action is
disabled.
The recommended value of DRC hysteresis is 3 dB.
5.5.4.3 DRC Hold
DRC hold is intended to slow the start of decay for a specified period of time in response to a decrease in
energy level. To minimize audible artifacts, TI recommends to set the DRC hold time to 0 through
programming page 0 / register 69, bits D6–D3 = 0000.
5.5.4.4 DRC Attack Rate
When the output of the DAC digital volume control exceeds the programmed DRC threshold, the gain
applied in the DAC digital volume control is progressively reduced to avoid the signal from saturating the
channel. This process of reducing the applied gain is called attack. To avoid audible artifacts, the gain is
reduced slowly with a rate equaling the attack rate, programmable via page 0 / register 70, bits D7–D4.
Attack rates can be programmed from 4-dB gain change per sample period to 1.2207e–5-dB gain change
per sample period.
Attack rates should be programmed such that before the output of the DAC digital volume control can clip,
the input signal should be sufficiently attenuated. High attack rates can cause audible artifacts, and too-
slow attack rates may not be able to prevent the input signal from clipping.
The recommended DRC attack rate value is 1.9531e–4 dB per sample period.
5.5.4.5 DRC Decay Rate
When the DRC detects a reduction in output signal swing beyond the programmed DRC threshold, the
DRC enters a decay state, where the applied gain in the digital-volume control is gradually increased to
programmed values. To avoid audible artifacts, the gain is slowly increased with a rate equal to the decay
rate programmed through page 0 / register 70, bits D3–D0. The decay rates can be programmed from
1.5625e–3 dB per sample period to 4.7683e–7 dB per sample period. If the decay rates are programmed
too fast, then sudden gain changes can cause audible artifacts. However, if it is programmed too slow,
then the output may be perceived as too low for a long time after the peak signal has passed.
The recommended value of DRC decay rate is 2.4414e–5 dB per sample period.
5.5.4.6 Example Setup for DRC
•
•
•
•
•
•
Digital Vol gain = 12 dB
Threshold = –24 dB
Hysteresis = 3 dB
Hold time = 0 ms
Attack rate = 1.9531e–4 dB per sample period
Decay rate = 2.4414e–5 dB per sample period
Script
Copyright © 2013, Texas Instruments Incorporated
APPLICATION INFORMATION
35
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
#Go to Page 0
w 30 00 00
#DAC => 12 db gain left
w 30 41 18
#DAC => 12 db gain right
w 30 42 18
#DAC => DRC Enabled for both channels, Threshold = -24 db, Hysteresis = 3 dB
w 30 44 7F
#DRC Hold = 0 ms, Rate of Changes of Gain = 0.5 dB/Fs'
w 30 45 00
#Attack Rate = 1.9531e-4 dB/Frame , DRC Decay Rate =2.4414e-5 dB/Frame
w 30 46 B6
#Go to Page 9
w 30 00 09
#DRC HPF
w 30 0E 7F AB 80 55 7F 56
#DRC LPF W 30 14 00 11 00 11 7F DE
5.5.5 Headphone Detection
The TLV320DAC3100-Q1 includes capability to monitor a headphone jack to determine if a plug has been
inserted into the jack. Figure 5-18 shows the circuit configuration to enable this feature.
HPR
HPL
VOL/MICDET
Micdet
Micbias
MICBIAS
Figure 5-18. Jack Connections for Headphone Detection
Headphone Detection is enabled by programming page 0 / register 67, bit D1. In order to avoid false
detections due to mechanical vibrations in headset jacks or microphone buttons, a debounce function is
provided for glitch rejection. For the case of headset insertion, a debounce function with a range of 32 ms
to 512 ms is provided. This can be programmed via page 0 / register 67, bits D4–D2. For improved button-
press detection, the debounce function has a range of 8 ms to 32 ms by programming page 0 / register
67, bits D1–D0.
The TLV320DAC3100-Q1 also provides feedback to the user through register-readable flags, as well as n
interrupt on the I/O pins when a button press or a headset insertion/removal event is detected. The value
in page 0 / register 46, bits D5–D4 provides the instantaneous state of button press and headset insertion.
Page 0 / register 44, bit D5 is a sticky (latched) flag that is set when the button-press event is detected.
Page 0 / register 44, bit D4 is a sticky flag which is set when the headset insertion or removal event is
detected. These sticky flags are set by the event occurrence, and are reset only when read. This requires
polling page 0 / register 44. To avoid polling and the associated overhead, the TLV320DAC3100-Q1 also
provides an interrupt feature, whereby events can trigger the INT1, the INT2, or both interrupts. These
interrupt events can be routed to one of the digital output pins. See Section 5.5.6 for details.
36
APPLICATION INFORMATION
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
The TLV320DAC3100-Q1 not only detects a headset insertion event, but also is able to distinguish
between the different headsets inserted, such as stereo headphones or cellular headphones. After the
headset-detection event, the user can read page 0 / register 67, bits D6–D5 to determine the type of
headset inserted.
Table 5-21. Headphone Detection Block Registers
Register
Page 0 / register 67, bits D4–D2
Page 0 / register 67, bits D1–D0
Page 0 / register 44, bit D5
Page 0 / register 44, bit D4
Page 0 / register 46, bit D5
Page 0 / register 46, bit D4
Page 0 / register 67, bits D6–D5
Description
Debounce programmability for headset detection
Debounce programmability for button press
Sticky flag for button-press event
Sticky flag for headset-insertion or -removal event
Status flag for button-press event
Status flag for headset insertion and removal
Flags for type of headset detected
The headset detection block requires AVDD to be powered. The headset detection feature in the
TLV320DAC3100-Q1 is achieved with very low power overhead, requiring less than 20 μA of additional
current from the AVDD supply.
5.5.6 Interrupts
Some specific events in the TLV320DAC3100-Q1 which may require host processor intervention, can be
used to trigger interrupts to the host processor. This avoids polling the status-flag registers continuously.
The TLV320DAC3100-Q1 has two defined interrupts, INT1 and INT2, that can be configured by
programming page 0 / register 48 and page 0 / register 49. A user can configure interrupts INT1 and INT2
to be triggered by one or many events, such as:
•
•
•
•
•
Headset detection
Button press
DAC DRC signal exceeding threshold
Overcurrent condition in headphone drivers and speaker drivers
Data overflow in ADC and DAC processing blocks and filters
Each of these INT1 and INT2 interrupts can be routed to output pins GPIO1. These interrupt signals can
either be configured as a single pulse or a series of pulses by programming page 0 / register 48, bit D0
and page 0 / register 49, bit D0. If the user configures the interrupts as a series of pulses, the events
trigger the start of pulses that stop when the flag registers in page 0 / registers 44, 45, and 50 are read by
the user to determine the cause of the interrupt.
5.5.7 Key-Click Functionality With Digital Sine-Wave Generator (PRB_P25)
A special algorithm has been included in the digital signal processing block PRB_P25 for generating a
digital sine-wave signal that is sent to the DAC. The digital sine-wave generator is also referred to as the
beep generator in this document.
This functionality is intended for generating key-click sounds for user feedback. The sine-wave generator
is very flexible (see Table 5-22) and is completely register programmable. Programming page 0 / register
71 through page 0 / register 79 (8 bits each) completely controls the functionality of this generator and
allows for differentiating sounds.
The two registers used for programming the 16-bit sine-wave coefficient are page 0 / register 76 and
page 0 / register 77. The two registers used for programming the 16-bit cosine-wave coefficient are
page 0 / register 78 and page 0 / register 79. This coefficient resolution allows virtually any frequency of
sine wave in the audio band to be generated, up to fS / 2.
Copyright © 2013, Texas Instruments Incorporated
APPLICATION INFORMATION
37
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
The three registers used to control the length of the sine-burst waveform are page 0 / register 73 through
page 0 / register 75. The resolution (bit) in the registers of the sine-burst length is one sample time, so this
allows great control on the overall time of the sine-burst waveform. This 24-bit length timer supports 16
777 215 sample times. For example, if fS is set at 48 kHz, and the register value equals 96 000 d
(01 7700h), then the sine burst lasts exactly 2 seconds. The default settings for the tone generator, based
on using a sample rate of 48 kHz, are 1-kHz (approximately) sine wave, with a sine-burst length of five
cycles (5 ms).
Table 5-22. Beep Generator Register Locations (Page 0x00)
BEEP LENGTH
SINE
COSINE
LEFT BEEP CONTROL RIGHT BEEP CONTROL
71 72
MSB
73
MID
LSB
MSB
LSB
MSB
78
LSB
REGISTER
74
75
76
77
79
Table 5-23. Example Beep-Generator Settings for a 1000-Hz Tone
BEEP FREQUENCY
BEEP LENGTH
SINE
COSINE
SAMPLE RATE
MSB
(hex)
MID
(hex)
LSB
(hex)
MSB
(hex)
LSB
(hex)
MSB
(hex)
LSB
(hex)
Hz
Hz
1000(1)
0
0
EE
10
D8
7E
E3
48 000
(1) These are the default settings.
Two registers are used to control the left sine-wave volume and the right sine-wave volume independently.
The 6-bit digital volume control used allows level control of 2 dB to –61 dB in 1-dB steps. The left-channel
volume is controlled by writing to page 0 / register 71, bits D5–D0. The right-channel volume is controlled
by writing to page 0, register 72, bits D5–D0. A master volume control that controls the left and right
channels of the beep generator can be set up by writing to page 0 / register 72, bits D7–D6. The default
volume control setting is 2 dB, which provides the maximum tone-generator output level.
For generating other tones, the three tone-generator coefficients can be found by running the following
script using MATLAB™ :
Sine = round(sin(2*π*Fin/Fs)*32768)
Cosine = round(cos(2*π*Fin/Fs)*32768)
Beep Length = floor(Cycles*Fs/Fin)
where,
Fin = Beep frequency desired
Fs = Sample rate
Cycle = Number of beep (sine wave) cycles that are required
NOTES:
1. Fin must always be less than 0.5*Fs and cannot equal 0 or 0.25*Fs.
2. For the sine and cosine values, if the number of bits is less than the full 16-bit value, then the unused
MSBs must be written as 0s.
3. For the beep-length values, if number of bits is less than the full 24-bit value, then the unused MSBs
must be written as 0s.
Following the beep-volume control is a digital mixer that mixes in a playback data stream whose level has
already been set by the DAC volume control. Therefore, once the key-click volume level is set, the key-
click volume is not affected by the DAC volume control, which is the main control available to the end
user. This functionality is shown in Figure 1-1.
Following the DAC, the signal can be further scaled by the analog output volume control and power-
amplifier level control.
38
APPLICATION INFORMATION
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
The beep generator is used for the key-click function. A single beep is generated by writing to page 0 /
register 71, bit D7. After the programmed beep length has finished, register 71, bit D7 is reset back to
zero.
To insert a beep in the middle of an already-playing signal over DAC, use the following sequence.
Before the beep is desired, program the desired beep frequency, volume, and length in the configuration
registers. When a beep is desired, use the example configuration script.
w 30 00 00
w 30 40 0C
# change to Page 0
# mute DACs
f
30 26 xxx1xxx1
# wait for DAC gain flag to be set
# power down NDAC divider
# enable beep generator with left channel volume = 0dB, volume level could
be different as per requirement
w 30 0B 02
w 30 47 80
w 30 0B 82
w 30 40 00
# power up NDAC divider, in this specific example NDAC = 2, could be
different value as per overall setup
# un-mute DAC to resume playing audio
Note that in this scheme the audio signal on the DAC is temporarily muted to enable beep generation.
Because powering down of NDAC clock divider is required, do not use the DAC_CLK or DAC_MOD_CLK
for generation of I2S clocks.
5.5.8 Programming DAC Digital Filter Coefficients
The digital filter coefficients must be programmed through the I2C interface. All digital filtering for the DAC
signal path must be loaded into the RAM before the DAC is powered on. Note that default ALLPASS filter
coefficients for programmable biquads are located in boot ROM. The boot ROM automatically loads the
default values into the RAM following a hardware reset (toggling the RESET pin) or after a software reset.
After resetting the device, loading boot ROM coefficients into the digital filters requires 100 μs of
programming time. During this time, reading or writing to page 8 through page 15 for updating DAC filter
coefficient values is not permitted. The DAC should not be powered up until after all of the DAC
configurations have been done by the system microprocessor.
5.5.9 Updating DAC Digital Filter Coefficients During PLAY
When it is required to update the DAC digital filter coefficients or beep generator during play, care must be
taken to avoid click and pop noise or even a possible oscillation noise. These artifacts can occur if the
DAC coefficients are updated without following the proper update sequence. The correct sequence is
shown in Figure 5-19. The values for times listed in Figure 5-19 are conservative and should be used for
software purposes.
There is also an adaptive mode, in which DAC coefficients can be updated while the DAC is on. For
details, see Section 5.5.1.3.
Copyright © 2013, Texas Instruments Incorporated
APPLICATION INFORMATION
39
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
Play - Paused
Volume Ramp Down
Soft Mute
DAC Volume Ramp Down WAIT Time (A)
Wait (A) ms
For fS = 32 kHz ® Wait 25 ms (min)
For fS = 48 kHz ® Wait 20 ms (min)
DAC Power Down
Update
Digital Filter
Coefficients
DAC Volume Ramp Up Time (B)
For fS = 32 kHz ® 25 ms
For fS = 48 kHz ® 20 ms
DAC Power UP
Wait 20 ms
Restore Previous
Volume Level (Ramp)
in (B) ms
Play - Continue
F0024-02
Figure 5-19. Example Flow For Updating DAC Digital Filter Coefficients During Play
5.5.10 Digital Mixing and Routing
The TLV320DAC3100-Q1 has four digital mixing blocks. Each mixer can provide either mixing or
multiplexing of the digital audio data. This arrangement of digital mixers allows independent volume ontrol
for both the playback data and the key-click sound. The first set of mixers can be used to make monaural
signals from left and right audio data, or they can even be used to swap channels to the DAC. his function
is accomplished by selecting left audio data for the right DAC input, and right data for the left DAC input.
The second set of mixers provides mixing of the audio data stream and the key-click sound. The digital
routing can be configured by writing to page 0 / register 63, bits D5–D4 for the left channel and bits
D3–D2 for the right channel.
Because the key-click function uses the digital signal processing block, the CODEC_CLKIN, DAC, analog
volume control, and output driver must be powered on for the key-click sound to occur.
40
APPLICATION INFORMATION
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
5.5.11 Analog Audio Routing
The TLV320DAC3100-Q1 has the capability to route the DAC output to either the headphone or the
speaker output. If desirable, both output drivers can operate at the same time while playing at different
volume levels. The TLV320DAC3100-Q1 provides various digital routing capabilities, allowing digital
mixing or even channel swapping in the digital domain. All analog outputs other than the selected ones
can be powered down for optimal power consumption.
5.5.11.1 Analog Output Volume Control
The output volume control can be used to fine-tune the level of the mixer amplifier signal supplied to the
headphone driver or the speaker driver. This architecture supports separate and concurrent volume levels
for each of the four output drivers. This volume control can also be used as part of the output pop-noise
reduction scheme. This feature is available even if the DAC is powered down.
5.5.11.2 Headphone Analog-Output Volume Control
For the headphone outputs, the analog volume control has a range from 0 dB to –78 dB in 0.5-dB steps
for most of the useful range plus mute, which is shown in Table 5-24. This volume control includes soft-
stepping logic. Routing the left-channel DAC output signal to the left-channel analog volume control is
done by writing to page 1 / register 35, bit D6. Routing the right-channel DAC output signal to the right-
channel analog volume control is done by writing to page 1 / register 35, bit D2.
Changing the left-channel analog volume for the headphone is controlled by writing to page 1 / register 36,
bits D6–D0. Changing the right-channel analog volume for the headphone is controlled by writing to
page 1 / register 37, bits D6–D0. Routing the signal from the output of the left-channel analog volume
control to the input of the left-channel headphone power amplifier is done by writing to page 1 /
register 36, bit D7. Routing the signal from the output of the right-channel analog volume control to the
input of the right-channel headphone power amplifier is done by writing to page 1 / register 37, bit D7.
The analog volume-control soft-stepping time is based on the setting in page 0 / register 63, bits D1–D0.
Copyright © 2013, Texas Instruments Incorporated
APPLICATION INFORMATION
41
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
Table 5-24. Analog Volume Control for Headphone and Speaker Outputs (for D7 = 1)(1)
Register Value Analog Gain
Register Value Analog Gain
Register Value Analog Gain
Register Value Analog Gain
(D6–D0)
(dB)
(D6–D0)
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
(dB)
(D6–D0)
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
(dB)
(D6–D0)
(dB)
–45.2
–45.8
–46.2
–46.7
–47.4
–47.9
–48.2
–48.7
–49.3
–50
0
0
–15
–30.1
–30.6
–31.1
–31.6
–32.1
–32.6
–33.1
–33.6
–34.1
–34.6
–35.2
–35.7
–36.2
–36.7
–37.2
–37.7
–38.2
–38.7
–39.2
–39.7
–40.2
–40.7
–41.2
–41.7
–42.1
–42.7
–43.2
–43.8
–44.3
–44.8
90
1
–0.5
–1
–15.5
–16
91
2
92
3
–1.5
–2
–16.5
–17
93
4
94
5
–2.5
–3
–17.5
–18.1
–18.6
–19.1
–19.6
–20.1
–20.6
–21.1
–21.6
–22.1
–22.6
–23.1
–23.6
–24.1
–24.6
–25.1
–25.6
–26.1
–26.6
–27.1
–27.6
–28.1
–28.6
–29.1
–29.6
95
6
96
7
–3.5
–4
97
8
98
9
–4.5
–5
99
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117–127
–50.3
–51
–5.5
–6
–51.4
–51.8
–52.2
–52.7
–53.7
–54.2
–55.3
–56.7
–58.3
–60.2
–62.7
–64.3
–66.2
–68.7
–72.2
–78.3
–6.5
–7
–7.5
–8
–8.5
–9
–9.5
–10
–10.5
–11
–11.5
–12
–12.5
–13
–13.5
–14
–14.5
(1) Mute when D7 = 0 and D6–D0 = 127 (0x7F).
5.5.11.3 Class-D Speaker Analog Output Volume Control
For the mono speaker outputs, the analog volume control has a range from 0 dB to –78 dB in 0.5-dB
steps for most of the useful range plus mute, as seen in Table 5-24. The implementation includes soft-
stepping logic.
Routing the left-channel DAC output signal to the left-channel analog volume control is done by writing to
page 1 / register 35, bit D6. Routing the right-channel DAC output signal to the right-channel analog olume
control is done by writing to page 1 / register 35, bit D2. Changing the left-channel analog volume for the
speaker is controlled by writing to page 1 / register 38, bits D6–D0. Changing the right-channel analog
volume for the speaker is controlled by writing to page 1 / register 39, bits D6–D0.
Routing the signal from the output of the left-channel analog volume control to the input of the mono
speaker amplifier is done by writing to page 1 / register 38, bit D7.
The analog volume-control soft-stepping time is based on the setting in page 0 / register 63, bits D1–D0.
42
APPLICATION INFORMATION
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
5.5.12 Analog Outputs
Various analog routings are supported for playback. All the options can be conveniently viewed on the
functional block diagram, Figure 1-1.
5.5.12.1 Headphone Drivers
The TLV320DAC3100-Q1 features a stereo headphone driver (HPL and HPR) that delivers up to 30 mW
per channel, at 3.3-V supply voltage, into a 16-Ω load. The headphones are used in a single-ended
configuration where an ac-coupling capacitor (dc-blocking) is connected between the device output pins
and the headphones. The headphone driver also supports 32-Ω and 10-kΩ loads without changing any
control register settings.
The headphone drivers can be configured to optimize the power consumption in the lineout-drive mode by
writing 11 to page 1 / register 44, bits D2–D1.
The output common mode of the headphone and lineout drivers is programmed to 1.35 V, 1.5 V, 1.65 V,
or 1.8 V by setting page 1 / register 31, bits D4–D3. Set the common-mode voltage to ≤ AVDD / 2.
The left headphone driver can be powered on by writing to page 1 / register 31, bit D7. The right
headphone driver can be powered on by writing to page 1 / register 31, bit D6. The left-output driver gain
can be controlled by writing to page 1 / register 40, bits D6–D3, and it can be muted by writing to page 1 /
register 40, bit D2. The right-output driver gain can be controlled by writing to page 1 / register 41, bits
D6–D3, and it can be muted by writing to page 1 / register 41, bit D2.
The TLV320DAC3100-Q1 has a short-circuit protection feature for the headphone drivers, which is always
enabled to provide protection. The output condition of the headphone driver during short circuit is
programmed by writing to page 1 / register 31, bit D1. If D1 = 0 when a short circuit is detected, the device
limits the maximum current to the load. If D1 = 1 when a short circuit is detected, the device powers down
the output driver. The default condition for headphones is the current-limiting mode. In case of a short
circuit on either channel, the output is disabled and a status flag is provided as read-only bits on page 1 /
register 31, bit D0. If shutdown mode is enabled, then as soon as the short circuit is detected, page 1 /
register 31, bit D7 (for HPL) or page 1 / register 31, bit D6, or both (for HPR) clear automatically. Next, the
device requires a reset to re-enable the output stage. Resetting can be done in two ways. First, the device
master reset can be used, which requires either toggling the RESET pin or using the software reset. If
master reset is used, it resets all of the registers. Second, a dedicated headphone power-stage reset can
also be used to re-enable the output stage, and that keeps all of the other device settings. The headphone
power stage reset is done by setting page 1 / register 31, bit D7 for HPL and by setting page 1 /
register 31, bit D6 for HPR. If the fault condition has been removed, then the device returns to normal
operation. If the fault is still present, then another shutdown occurs. Repeated resetting (more than three
times) is not recommended, as this could lead to overheating.
5.5.12.2 Speaker Drivers
The TLV320DAC3100-Q1 an integrated class-D mono speaker driver (SPKP/SPKM) capable of driving a
4-Ω or an 8-Ω differential load. The speaker driver can be powered directly from the battery supply (2.7 V
to 5.5 V) on the SPKVDD pins; however, the voltage (including spike voltage) must be limited below the
absolute-maximum voltage of 6 V.
The speaker driver is capable of supplying 2.5 W with a 5.5-V power supply (4-Ω load). Through the use
of digital mixing, the device can connect one or both digital audio playback data channels to the speaker
driver.
The mono class-D speaker driver can be powered on by writing to page 1 / register 32, bit D7. The mono
output-driver gain can be controlled by writing to page 1 / register 42, bits D4–D3, and it can be muted by
writing to page 1 / register 42, bit D2.
Copyright © 2013, Texas Instruments Incorporated
APPLICATION INFORMATION
43
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
The TLV320DAC3100-Q1 has a short-circuit protection feature for the speaker drivers that is always
enabled to provide protection. If the output is shorted, the output stage shuts down on the overcurrent
condition. (Current limiting is not an available option for the higher-current speaker driver output stage.) In
case of a short circuit on either channel, the output is disabled and a status flag is provided as a read-only
bit on page 1 / register 32, bit D0.
If shutdown occurs due to an overcurrent condition, then the device requires a reset to re-enable the
output stage. Resetting can be done in two ways. First, the device master reset can be used, which
requires either toggling the RESET pin or using the software reset. If master reset is used, it resets all of
the registers. Second, a dedicated speaker power-stage reset can be used that keeps all of the other
device settings. The speaker power-stage reset is done by setting page 1 / register 32, bit D7 SPKP and
SPKM. If the fault condition has been removed, then the device returns to normal operation. If the fault is
still present, then another shutdown occurs. Repeated resetting (more than three times) is not
recommended, as this could lead to overheating.
To minimize battery current leakage, the SPKVDD and SPKVDD voltage levels should not be less
than the AVDD voltage level.
The TLV320DAC3100-Q1 has a thermal protection (OTP) feature for the speaker drivers which is always
enabled to provide protection. If the device overheats, then the output stops switching. When the device
cools down, the device resumes switching. An overtemperature status flag is provided as a read-only bit
on page 0 / register 3, bit D1. The OTP feature is for self-protection of the device. If die temperature can
be controlled at the system or board level, then overtemperature does not occur.
5.5.13 Audio-Output Stage-Power Configurations
After the device has been configured (following a RESET) and the circuitry has been powered up, the
audio output stage can be powered up and powered down by register control.
These functions soft-start automatically. By using these register controls, it is possible to control these
three output-stage configurations independently.
See Table 5-25 for register control of audio output stage power configurations.
Table 5-25. Audio-Output Stage-Power Configurations
Audio Output Pins
Desired Function
Power down HPL driver
Power up HPL driver
Page 1 / Register, Bit Values
Page 1 / register 31, bit D7 = 0
Page 1 / register 31, bit D7 = 1
Page 1 / register 31, bit D6 = 0
Page 1 / register 31, bit D6 = 1
Page 1 / register 32, bit D7 = 0
Page 1 / register 32, bit D7 = 1
HPL
Power down HPR driver
Power up HPR driver
HPR
Power down mono class-D drivers
Power up mono class-D drivers
SPKP / SPKM
5.5.14 DAC Setup
The following paragraphs are intended to guide a user through the steps necessary to configure the
TLV320DAC3100-Q1.
Step 1
The system clock source (master clock) and the targeted DAC sampling frequency must be identified.
Depending on the targeted performance, the decimation filter type (A, B, or C) and DOSR value can be
determined:
•
•
•
Filter A should be used for 48-kHz high-performance operation; DOSR must be a multiple of 8.
Filter B should be used for up to 96-kHz operations; DOSR must be a multiple of 4.
Filter C should be used for up to 192-kHz operations; DOSR must be a multiple of 2.
44
APPLICATION INFORMATION
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
In all cases, DOSR is limited in its range by the following condition:
2.8 MHz < DOSR × DAC_fS < 6.2 MHz
Based on the identified filter type and the required signal-processing capabilities, the appropriate
processing block can be determined from the list of available processing blocks (PRB_P1 to PRB_P25).
Based on the available master clock, the chosen DOSR and the targeted sampling rate, the clock-divider
values NDAC and MDAC can be determined. If necessary, the internal PLL can add a large degree of
flexibility.
In summary, CODEC_CLKIN (derived directly from the system clock source or from the internal PLL)
divided by MDAC, NDAC, and DOSR must be equal to the DAC sampling rate, DAC_fS. The
CODEC_CLKIN clock signal is shared with the DAC clock-generation block.
CODEC_CLKIN = NDAC × MDAC × DOSR × DAC_fS
To a large degree, NDAC and MDAC can be chosen independently in the range of 1 to 128. In general,
NDAC should be as large as possible as long as the following condition can still be met:
MDAC × DOSR / 32 ≥ RC
RC is a function of the chosen processing block and is listed in Table 5-11.
The common-mode voltage setting of the device is determined by the available analog power supply.
At this point, the following device-specific parameters are known: PRB_Px, DOSR, NDAC, MDAC, input
and output common-mode values. If the PLL is used, the PLL parameters P, J, D, and R are determined
as well.
Step 2
Setting up the device via register programming:
The following list gives an example sequence of items that must be executed in the time between
powering the device up and reading data from the device. Note that there are other valid sequences,
depending on which features are used.
1. Define starting point:
(a) Power up applicable external power supplies
(b) Set register page to 0
(c) Initiate SW reset
2. Program clock settings
(a) Program PLL clock dividers P, J, D, and R (if PLL is used)
(b) Power up PLL (if PLL is used)
(c) Program and power up NDAC
(d) Program and power up MDAC
(e) Program OSR value
(f) Program I2S word length if required (16, 20, 24, or 32 bits)
(g) Program the processing block to be used
(h) Micellaneous page 0 controls
Copyright © 2013, Texas Instruments Incorporated
APPLICATION INFORMATION
45
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
3. Program analog blocks
(a) Set register page to 1
(b) Program common-mode voltage
(c) Program headphone-specific de-pop settings (in case headphone driver is used)
(d) Program routing of DAC output to the output amplifier (headphone/lineout or speaker)
(e) Unmute and set gain of output drivers
(f) Power up output drivers
4. Apply waiting time determined by the de-pop settings and the soft-stepping settings of the driver gain,
or poll page 1 / register 63
5. Power up DAC
(a) Set register page to 0
(b) Power up DAC channels and set digital gain
(c) Unmute digital volume control
A detailed example can be found in Section 5.5.15.
5.5.15 Example Register Setup to Play Digital Data Through DAC and Headphone/Speaker
Outputs
A typical EVM I2C register control script follows to show how to set up the TLV320DAC3100-Q1 in
playback mode with fS = 44.1 kHz and MCLK = 11.2896 MHz.
# Key: w 30 XX YY ==> write to I2C address 0x30, to register 0xXX, data 0xYY
#
#
# ==> comment delimiter
# The following list gives an example sequence of items that must be executed in the time
# between powering the # device up and reading data from the device. Note that there are
# other valid sequences depending on which features are used.
# 1. Define starting point:
#
#
#
(a) Power up applicable external hardware power supplies
(b) Set register page to 0
w 30 00 00
#
#
(c) Initiate SW reset (PLL is powered off as part of reset)
#
w 30 01 01
#
# 2. Program clock settings
#
#
(a) Program PLL clock dividers P, J, D, R (if PLL is used)
# PLL_clkin = MCLK,codec_clkin = PLL_CLK
w 30 04 03
# J = 8
w 30 06 08
# D = 0000, D(13:8) = 0, D(7:0) = 0
w 30 07 00 00
#
#
(b) Power up PLL (if PLL is used)
# PLL Power up, P = 1, R = 1
#
w 30 05 91
#
#
#
(c) Program and power up NDAC
# NDAC is powered up and set to 8
w 30 0B 88
#
#
#
(d) Program and power up MDAC
# MDAC is powered up and set to 2
w 30 0C 82
#
#
(e) Program OSR value
46
APPLICATION INFORMATION
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
#
# DOSR = 128, DOSR(9:8) = 0, DOSR(7:0) = 128
w 30 0D 00 80
#
#
#
#
(f) Program I2S word length if required (16, 20, 24, 32 bits)
and master mode (BCLK and WCLK are outputs)
# mode is i2s, wordlength is 16, slave mode
w 30 1B 00
#
(g) Program the processing block to be used
#
# Select Processing Block PRB_P11
w 30 3C 0B
w 30 00 08
w 30 01 04
w 30 00 00
#
#
#
(h) Miscellaneous page 0 controls
# DAC => volume control thru pin disable
w 30 74 00
# 3. Program analog blocks
#
#
#
(a) Set register page to 1
w 30 00 01
#
#
(b) Program common-mode voltage (defalut = 1.35 V)
#
w 30 1F 04
#
#
(c) Program headphone-specific depop settings (in case headphone driver is used)
#
# De-pop, Power on = 800 ms, Step time = 4 ms
w 30 21 4E
#
#
#
(d) Program routing of DAC output to the output amplifier (headphone/lineout or speaker)
# LDAC routed to HPL out, RDAC routed to HPR out
w 30 23 44
#
#
#
(e) Unmute and set gain of output driver
# Unmute HPL, set gain = 0 db
w 30 28 06
# Unmute HPR, set gain = 0 dB
w 30 29 06
# Unmute Class-D, set gain = 18 dB
w 30 2A 1C
#
#
#
(f) Power up output drivers
# HPL and HPR powered up
w 30 1F C2
# Power-up Class-D driver
w 30 20 86
# Enable HPL output analog volume, set = -9 dB
w 30 24 92
# Enable HPR output analog volume, set = -9 dB
w 30 25 92
# Enable Class-D output analog volume, set = -9 dB
w 30 26 92
#
# 4. Apply waiting time determined by the de-pop settings and the soft-stepping settings
#
#
of the driver gain or poll page 1 / register 63
# 5. Power up DAC
#
(a) Set register page to 0
#
w 30 00 00
#
#
#
(b) Power up DAC channels and set digital gain
Copyright © 2013, Texas Instruments Incorporated
APPLICATION INFORMATION
47
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
# Powerup DAC left and right channels (soft step enabled)
w 30 3F D4
#
# DAC Left gain = -22 dB
w 30 41 D4
# DAC Right gain = -22 dB
w 30 42 D4
#
#
#
(c) Unmute digital volume control
# Unmute DAC left and right channels
w 30 40 00
5.6 CLOCK Generation and PLL
The TLV320DAC3100-Q1 supports a wide range of options for generating clocks for the DAC section as
well as interface and other control blocks, as shown in Figure 5-20. The clocks for the DAC require a
source reference clock. This clock can be provided on variety of device pins, such as the MCLK, BCLK, or
GPIO1 pins. The source reference clock for the codec can be chosen by programming the
CODEC_CLKIN value on page 0 / register 4, bits D1–D0. CODEC_CLKIN can then be routed through
highly-flexible clock dividers, shown in Figure 5-20, to generate the various clocks required for the DAC. In
the event that the desired audio clocks cannot be generated from the reference clocks on MCLK, BCLK,
or GPIO1, the TLV320DAC3100-Q1 also provides the option of using the on-chip PLL, which supports a
wide range of fractional multiplication values to generate the required clocks. Starting from
CODEC_CLKIN, the TLV320DAC3100-Q1 provides several programmable clock dividers to help achieve
a variety of sampling rates for the DAC.
48
APPLICATION INFORMATION
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
BCLK
DIN
MCLK
GPIO1
PLL_CLKIN
PLL
´ (R ´ J.D)/P
GPIO1
BCLK
MCLK
PLL_CLK
CODEC_CLKIN
NDAC = 1, 2, ..., 127, 128
¸ NDAC
To DAC MAC
DAC_CLK
MDAC = 1, 2, ..., 127, 128
¸ MDAC
DAC_MOD_CLK
DOSR = 1, 2, ..., 1023, 1024
¸ DOSR
DAC_fS
B0357-04
Figure 5-20. Clock Distribution Tree
CODEC _ CLKIN
DAC _MOD _ CLK =
NDAC ´MDAC
CODEC _ CLKIN
DAC _ fS =
NDAC ´MDAC ´DOSR
(5)
Table 5-26. CODEC CLKIN Clock Dividers
Divider
Bits
NDAC
MDAC
DOSR
Page 0 / register 11, bits D6–D0
Page 0 / register 12, bits D6–D0
Page 0 / register 13, bits D1–D0 and page 0 / register 14, bits D7–D0
Copyright © 2013, Texas Instruments Incorporated
APPLICATION INFORMATION
49
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
The DAC modulator is clocked by DAC_MOD_CLK. For proper power-up operation of the DAC channel,
DAC_MOD_CLK must be enabled by configuring the NDAC and MDAC clock dividers (page 0 /
register 11, bit D7 = 1 and page 0 / register 12, bit D7 = 1). When the DAC channel is powered down, the
device internally initiates a power-down sequence for proper shutdown. During this shutdown sequence,
the NDAC and MDAC dividers must not be powered down, or else a proper low-power shutdown may not
take place. The user can read back the power-status flag at page 0 / register 37, bit D7 and page 0 /
register 37, bit D3. When both the flags indicate power-down, the MDAC divider may be powered down,
followed by the NDAC divider.
In general, for proper operation, all the root clock dividers should be powered down only after the child
clock dividers have been powered down.
The TLV320DAC3100-Q1 also has options for routing some of the internal clocks to the GPIO1 pin to be
used as general-purpose clocks in the system. The feature is shown in Figure 5-22.
DAC_CLK DAC_MOD_CLK
BDIV_CLKIN
N = 1, 2, ..., 127, 128
÷N
BCLK
B0362-01
Figure 5-21. BCLK Output Options
In the mode when the TLV320DAC3100-Q1 is configured to drive the BCLK pin (page 0 / register 27,
bit D3 = 1), it can be driven as the divided value of BDIV_CLKIN. The division value can be programmed
in page 0 / register 30, bits D6–D0 from 1 to 128. BDIV_CLKIN can itself be configured to be one of
DAC_CLK (DAC processing clock), DAC_MOD_CLK by configuring the BDIV_CLKIN multiplexer in page
0 / register 29, bits D1–D0. Additionally, a general-purpose clock can be driven out on GPIO1.
This clock can be a divided-down version of CDIV_CLKIN. The value of this clock divider can be
programmed from 1 to 128 by writing to page 0 / register 26, bits D6–D0. CDIV_CLKIN can itself be
programmed as one of the clocks among the list shown in Figure 5-22. This can be controlled by
programming the multiplexer in page 0 / register 25, bits D2–D0.
50
APPLICATION INFORMATION
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
PLL_CLK
DAC_MOD_CLK
DAC_CLK
MCLK
BCLK
DIN
CDIV_CLKIN
M = 1, 2, ..., 127, 128
÷ M
GPIO1 (CLKOUT)
B0363-01
Figure 5-22. General-Purpose Clock Output Options
Table 5-27. Maximum TLV320DAC3100-Q1 Clock Frequencies
Clock
CODEC_CLKIN
DVDD ≥ 1.65 V
≤ 110 MHz
DAC_CLK (DAC processing clock)
DAC_MAC_CLK
≤ 49.152 MHz
≤ 49.152 MHz with DRC disabled
≤ 48 MHz with DRC enabled
DAC_MOD_CLK
DAC_fS
6.758 MHz
0.192 MHz
55 MHz
BDIV_CLKIN
CDIV_CLKIN
100 MHz when M is odd
110 MHz when M is even
5.6.1 PLL
For lower power consumption, it is best to derive the internal audio processing clocks using the simple
dividers. When the input MCLK or other source clock is not an integer multiple of the audio processing
clocks, then it is necessary to use the onboard PLL. The TLV320DAC3100-Q1 fractional PLL can be used
to generate an internal master clock used to produce the processing clocks needed by the DAC. The
programmability of this PLL allows operation from a wide variety of clocks that may be available in the
system.
The PLL input supports clocks varying from 512 kHz to 20 MHz and is register-programmable to enable
generation of the required sampling rates with fine resolution. The PLL can be turned on by writing to
page 0 / register 5, bit D7. When the PLL is enabled, the PLL output clock, PLL_CLK, is given by the
following equation:
PLL_CLKIN´R ´ J.D
PLL_CLK =
P
(6)
where
R = 1, 2, 3, ..., 16 (page 0 / register 5, default value = 1)
J = 1, 2,3, … , 63, (page 0 / register 6, default value = 4)
D = 0, 1, 2, …, 9999 (page 0 / register 7 and page 0 / register 8, default value = 0)
P = 1, 2, 3, …, 8 (page 0 / register 5, default value = 1)
Copyright © 2013, Texas Instruments Incorporated
APPLICATION INFORMATION
51
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
The PLL can be turned on via page 0 / register 5, bit D7. The variable P can be programmed via page 0 /
register 5, bits D6–D4. The variable R can be programmed via page 0 / register 5, bits D3–D0. The
variable J can be programmed via page 0 / register 6, bits D5–D0. The variable D is 14 bits and is
programmed into two registers. The MSB portion can be programmed via page 0 / register 7, bits D5–D0,
and the LSB portion is programmed via page 0 / register 8, bits D7–D0. For proper update of the D divider
value, page 0 / register 7 must be programmed first, followed immediately by page 0 / register 8. Unless
the write to page 0 / register 8 is completed, the new value of D does not take effect.
When the PLL is enabled, the following conditions must be satisfied:
•
When the PLL is enabled and D = 0, the following conditions must be satisfied for PLL_CLKIN:
PLL _CLKIN
512 kHz £
£ 20 MHz
P
80 MHz ≤ (PLL_CLKIN × J.D × R/P)≤ 110 MHz
4 ≤ R × J ≤ 259
(7)
(8)
•
When the PLL is enabled and D ≠ 0, the following conditions must be satisfied for PLL_CLKIN:
PLL _CLKIN
10 MHz £
£ 20 MHz
P
80 MHz ≤ PLL_CLKIN × J.D × R/P ≤ 110 MHz
R = 1
The PLL can be powered up independently from the DAC block, and can also be used as a general-
purpose PLL by routing its output to the GPIO output. After powering up the PLL, PLL_CLK is available
typically after 10 ms.
The clock for the codec and various signal processing blocks, CODEC_CLKIN, can be generated from the
MCLK input, BCLK input, GPIO input, or PLL_CLK (page 0 / register 4, bits D1–D0).
If CODEC_CLKIN is derived from the PLL, then the PLL must be powered up first and powered down last.
Table 5-28 lists several example cases of typical PLL_CLKIN rates and how to program the PLL to
achieve a sample rate fS of either 44.1 kHz or 48 kHz.
Table 5-28. PLL Example Configurations
PLL_CLKIN (MHz)
PLLP
PLLR
PLLJ
PLLD
MDAC
NDAC
DOSR
fS = 44.1 kHz
2.8224
5.6448
12
1
1
1
1
1
1
4
3
3
1
1
1
1
1
10
5
0
0
3
3
3
6
3
3
3
5
5
5
3
5
5
5
128
128
128
104
128
128
128
7
560
3504
2920
4100
560
13
6
16
5
19.2
4
48
7
fS = 48 kHz
2.048
3.072
4.096
6.144
8.192
12
1
1
1
1
1
1
1
1
3
4
3
2
4
1
1
1
14
7
0
0
7
7
7
7
4
7
7
7
2
2
2
2
4
2
2
2
128
128
128
128
128
128
128
128
7
0
7
0
3
0
7
1680
3760
4800
16
5
19.2
4
52
APPLICATION INFORMATION
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
Table 5-28. PLL Example Configurations (continued)
PLL_CLKIN (MHz)
fS = 44.1 kHz
48
PLLP
PLLR
PLLJ
PLLD
MDAC
NDAC
DOSR
4
1
7
1680
7
2
128
5.6.2 Timer
The internal clock runs nominally at 8.2 MHz. This is used for various internal timing intervals, de-bounce
logics and interrupts. The MCLK divider must be set such a way that the divider output is ~1 MHz for the
timers to be closer to the programmed value.
Powered on if
internal oscillator is
selected
Internal
Oscillator
÷8
0
Used for de-bounce time for
headset detection logic,
Interval timers
various power up timers and
for generation of interrupts
MCLK
Programmable
Divider
1
P3/R16, Bits D6-D0
P3/R16, Bit D7
Figure 5-23. Interval Timer Clock Selection
5.7 Digital Audio and Control Interface
5.7.1 Digital Audio Interface
Audio data is transferred between the host processor and the TLV320DAC3100-Q1 via the digital audio
data serial interface, or audio bus. The audio bus on this device is very flexible, including left- or right-
justified data options, support for I2S or PCM protocols, programmable data-length options, a TDM mode
for multichannel operation, very flexible master/slave configurability for each bus-clock line, and the ability
to communicate directly with multiple devices within a system.
The audio bus of the TLV320DAC3100-Q1 can be configured for left- or right-justified, I2S, DSP, or TDM
modes of operation, where communication with standard telephony PCM interfaces is supported within the
TDM mode. These modes are all MSB-first, with data width programmable as 16, 20, 24, or 32 bits by
configuring page 0 / register 27, bits D5–D4. In addition, the word clock and bit clock can be
independently configured in either master or slave mode for flexible connectivity to a wide variety of
processors. The word clock is used to define the beginning of a frame, and may be programmed as either
a pulse or a square-wave signal. The frequency of this clock corresponds to the DAC sampling frequency.
The bit clock is used to clock in and clock out the digital audio data across the serial bus. When in master
mode, this signal can be programmed to generate variable clock pulses by controlling the bit-clock divider
in page 0 / register 30 (see Figure 5-20). The number of bit-clock pulses in a frame may need adjustment
to accommodate various word lengths, as well as to support the case when multiple TLV320DAC3100-
Q1s may share the same audio bus.
Copyright © 2013, Texas Instruments Incorporated
APPLICATION INFORMATION
53
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
The TLV320DAC3100-Q1 also includes a feature to offset the position of start-of-data-transfer with
respect to the word clock. This offset can be controlled in terms of number of bit clocks and can be
programmed in page 0 / register 28.
The TLV320DAC3100-Q1 also has the feature of inverting the polarity of the bit clock used for transferring
the audio data as compared to the default clock polarity used. This feature can be used independently of
the mode of audio interface chosen. This can be configured via page 0 / register 29, bit D3.
By default, when the word clocks and bit clocks are generated by the TLV320DAC3100-Q1, these clocks
are active only when the DAC is powered up within the device. This is done to save power. However, it
also supports a feature whereby both the word clocks and bit clocks can be active even when the codec in
the device is powered down. This is useful when using the TDM mode with multiple codecs on the same
bus, or when word clocks or bit clocks are used in the system as general-purpose clocks.
5.7.1.1 Right-Justified Mode
The audio interface of the TLV320DAC3100-Q1 can be put into the right-justified mode by programming
page 0 / register 27, bits D7–D6 = 10. In right-justified mode, the LSB of the left channel is valid on the
rising edge of the bit clock preceding the falling edge of the word clock. Similarly, the LSB of the right
channel is valid on the rising edge of the bit clock preceding the rising edge of the word clock.
1/fS
WCLK
BCLK
Right Channel
Left Channel
DIN
0
n–1 n–2 n–3
MSB
2
1
0
n–1 n–2 n–3
2
1
0
LSB
T0149-05
Figure 5-24. Timing Diagram for Right-Justified Mode
For the right-justified mode, the number of bit clocks per frame should be greater than or equal to twice
the programmed word length of the data.
5.7.1.2 Left-Justified Mode
The audio interface of the TLV320DAC3100-Q1 can be put into left-justified mode by programming page 0
/ register 27, bits D7–D6 = 11. In left-justified mode, the MSB of the right channel is valid on the rising
edge of the bit clock following the falling edge of the word clock. Similarly, the MSB of the left channel is
valid on the rising edge of the bit clock following the rising edge of the word clock.
54
APPLICATION INFORMATION
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
WORD
CLOCK
LEFT CHANNEL
RIGHT CHANNEL
BIT
CLOCK
N
-
N
-
N
-
N
-
N
-
N
-
N
-
N
-
N
-
3
2
1
0
3
2
1
0
DATA
1
2
3
1
2
3
1
2
3
LD(n)
RD(n)
LD(n+1)
LD(n) = n'th sample of left channel data
RD(n) = n'th sample of right channel data
Figure 5-25. Timing Diagram for Left-Justified Mode
WORD
CLOCK
LEFT CHANNEL
RIGHT CHANNEL
BIT
CLOCK
N
-
N
-
N
-
N
-
N
-
N
-
N
-
N
-
N
-
3
2
1
0
3
2
1
0
DATA
1
2
3
1
2
3
1
2
3
LD(n)
RD(n)
LD(n+1)
LD(n) = n'th sample of left channel data
RD(n) = n'th sample of right channel data
Figure 5-26. Timing Diagram for Left-Justified Mode With Offset = 1
WORD
CLOCK
LEFT CHANNEL
RIGHT CHANNEL
BIT
CLOCK
N
-
N
-
N
-
N
-
N
-
N
-
N
-
N
-
N
-
3
2
1
0
3
2
1
0
3
DATA
1
2
3
1
2
3
1
2
3
LD(n)
RD(n)
LD(n+1)
LD(n) = n'th sample of left channel data
RD(n) = n'th sample of right channel data
Figure 5-27. Timing Diagram for Left-Justified Mode With Offset = 0 and Inverted Bit Clock
For the left-justified mode, the number of bit clocks per frame should be greater than or equal to twice the
programmed word length of the data. Also, the programmed offset value should be less than the number
of bit clocks per frame by at least the programmed word length of the data.
5.7.1.3 I2S Mode
The audio interface of the TLV320DAC3100-Q1 can be put into I2S mode by programming page 0 /
register 27, bits D7–D6 = 00. In I2S mode, the MSB of the left channel is valid on the second rising edge
of the bit clock after the falling edge of the word clock. Similarly, the MSB of the right channel is valid on
the second rising edge of the bit clock after the rising edge of the word clock.
Copyright © 2013, Texas Instruments Incorporated
APPLICATION INFORMATION
55
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
WORD
CLOCK
LEFT CHANNEL
RIGHT CHANNEL
BIT
CLOCK
N
-
N
-
N
-
N
-
N
-
N
-
N
-
N
-
N
-
3
2
1
0
3
2
1
0
3
DATA
1
2
3
1
2
3
1
2
3
LD(n)
RD(n)
LD(n+1)
LD(n) = n'th sample of left channel data
RD(n) = n'th sample of right channel data
Figure 5-28. Timing Diagram for I2S Mode
WORD
CLOCK
LEFT CHANNEL
RIGHT CHANNEL
BIT
CLOCK
N
-
N
-
N
-
DATA
5
4
3
2
1
0
5
4
3
2
1
0
5
1
1
1
LD(n)
LD(n) = n'th sample of left channel data
RD(n)
RD(n) = n'th sample of right channel data
LD(n+1)
Figure 5-29. Timing Diagram for I2S Mode With Offset = 2
WORD
CLOCK
LEFT CHANNEL
RIGHT CHANNEL
BIT
CLOCK
N
-
N
-
N
-
N
-
N
-
N
-
N
-
N
-
N
-
3
2
1
0
3
2
1
0
3
DATA
1
2
3
1
2
3
1
2
3
LD(n)
RD(n)
LD(n+1)
LD(n) = n'th sample of left channel data
RD(n) = n'th sample of right channel data
Figure 5-30. Timing Diagram for I2S Mode With Offset = 0 and Bit Clock Inverted
For I2S mode, the number of bit clocks per channel should be greater than or equal to the programmed
word length of the data. Also, the programmed offset value should be less than the number of bit clocks
per frame by at least the programmed word length of the data.
5.7.1.4 DSP Mode
The audio interface of the TLV320DAC3100-Q1 can be put into DSP mode by programming page 0 /
register 27, bits D7–D6 = 01. In DSP mode, the falling edge of the word clock starts the data transfer with
the left-channel data first and immediately followed by the right-channel data. Each data bit is valid on the
falling edge of the bit clock.
56
APPLICATION INFORMATION
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
WORD
CLOCK
LEFT CHANNEL
RIGHT CHANNEL
BIT
CLOCK
N
-
N
-
N
-
N
-
N
-
N
-
N
-
N
-
N
-
3
2
1
0
3
2
1
0
3
DATA
1
2
3
1
2
3
1
2
3
LD(n)
RD(n)
LD(n+1)
LD(n) = n'th sample of left channel data
RD(n) = n'th sample of right channel data
Figure 5-31. Timing Diagram for DSP Mode
WORD
CLOCK
LEFT CHANNEL
RIGHT CHANNEL
BIT
CLOCK
N
-
N
-
N
-
N
-
N
-
N
-
N
-
N
-
N
-
3
2
1
0
3
2
1
0
DATA
1
2
3
1
2
3
1
2
3
LD(n)
RD(n)
LD(n+1)
LD(n) = n'th sample of left channel data
RD(n) = n'th sample of right channel data
Figure 5-32. Timing Diagram for DSP Mode With Offset = 1
WORD
CLOCK
LEFT CHANNEL
RIGHT CHANNEL
BIT
CLOCK
N
-
N
-
N
-
N
-
N
-
N
-
N
-
N
-
N
-
3
2
1
0
3
2
1
0
3
DATA
1
2
3
1
2
3
1
2
3
LD(n)
RD(n)
LD(n+1)
Figure 5-33. Timing Diagram for DSP Mode With Offset = 0 and Bit Clock Inverted
For the DSP mode, the number of bit clocks per frame should be greater than or equal to twice the
programmed word length of the data. Also, the programmed offset value should be less than the number
of bit clocks per frame by at least the programmed word length of the data.
5.7.2 Primary and Secondary Digital Audio Interface Selection
The audio serial interface on the TLV320DAC3100-Q1 has extensive I/O control to allow communication
with two independent processors for audio data. The processors can communicate with the device one at
a time. This feature is enabled by register programming of the various pin selections. Table 5-29 shows
the primary and secondary audio interface selection and registers. Figure 5-34 is a high-level diagram
showing the general signal flow and multiplexing for the primary and secondary audio interfaces.
Table 5-29. Primary and Secondary Audio Interface Selection
Desired Pin
Function
Possible
Pins
Page 0 Registers
Comment
R27/D2 = 1
R33/D5–D4
Primary WCLK is output from codec
Select source of primary WCLK (DAC_fs or secondary WCLK)
Primary WCLK
(OUT)
WCLK
Copyright © 2013, Texas Instruments Incorporated
APPLICATION INFORMATION
57
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
Table 5-29. Primary and Secondary Audio Interface Selection (continued)
Desired Pin
Function
Possible
Pins
Page 0 Registers
Comment
Primary WCLK (IN)
WCLK
R27/D2 = 0
Primary WCLK is input to codec
R27/D3 = 1
Primary BCLK is output from codec
Primary BCLK
(OUT)
BCLK
R33/D7
Select source of primary WCLK (internal BCLK or secondary BCLK)
Primary BCLK is input to codec
Primary BCLK (IN)
Primary DIN (IN)
BCLK
DIN
R27/D3 = 0
R32/D0
Select DIN to internal interface (0 = primary DIN; 1 = secondary DIN)
Secondary WCLK obtained from GPIO1 pin
GPIO1 = secondary WCLK output
R31/D4–D2 = 000
R51/D5–D2 = 1001
R33/D3–D2
Secondary WCLK
(OUT)
GPIO1
GPIO1
GPIO1
Select source of secondary WCLK (DAC_fs, or primary WCLK)
Secondary WCLK obtained from GPIO1 pin
GPIO1 enabled as secondary input
R31/D4–D2 = 000
R51/D5–D2 = 0001
R31/D7–D5 = 000
R51/D5–D2 = 1000
R33/D6
Secondary WCLK
(IN)
Secondary BCLK obtained from GPIO1 pin
GPIO1 = secondary BCLK output
Secondary BCLK
(OUT)
Select source of secondary BCLK (primary BCLK or internal BCLK)
Secondary BCLK obtained from GPIO1 pin
GPIO1 enabled as secondary input
R31/D7–D5 = 000
R51/D5–D2 = 0001
R31/D1–D0 = 00
R51/D5–D2 = 0001
Secondary BCLK
(IN)
GPIO1
GPIO1
Secondary DIN obtained from GPIO1 pin
Secondary DIN (IN)
GPIO1 enabled as secondary input
58
APPLICATION INFORMATION
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
S_BCLK
BCLK
BCLK
BCLK
BCLK_OUT
BCLK_INT
S_BCLK
WCLK
S_WCLK
DAC_fS
WCLK
WCLK
Audio
DAC_WCLK_INT
Digital
Primary
Audio
Processor
Serial
Interface
S_WCLK
DOUT
DIN
DIN
DIN_INT
S_DIN
DIN
BCLK2
WCLK2
GPIO1
S_BCLK
S_WCLK
S_DIN
BCLK
BCLK
BCLK_OUT
GPIO1
GPIO1
WCLK
BCLK_OUT
Clock
WCLK
DAC_fS
Secondary
Audio
Processor
Generation
DAC_fS
DOUT
DIN
B0375-01
Figure 5-34. Audio Serial Interface Multiplexing
5.7.3 Control Interface
The TLV320DAC3100-Q1 control interface supports the I2C communication protocol.
5.7.3.1 I2C Control Mode
The TLV320DAC3100-Q1 supports the I2C control protocol and responds to the I2C address of 0011 000.
I2C is a two-wire, open-drain interface supporting multiple devices and masters on a single bus. Devices
on the I2C bus only drive the bus lines LOW by connecting them to ground; they never drive the bus lines
HIGH. Instead, the bus wires are pulled HIGH by pullup resistors, so the bus wires are HIGH when no
device is driving them LOW. This way, two devices cannot conflict; if two devices drive the bus
simultaneously, there is no driver contention.
Copyright © 2013, Texas Instruments Incorporated
APPLICATION INFORMATION
59
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
Communication on the I2C bus always takes place between two devices, one acting as the master and the
other acting as the slave. Both masters and slaves can read and write, but slaves can only do so under
the direction of the master. Some I2C devices can act as masters or slaves, but the TLV320DAC3100-Q1
can only act as a slave device.
An I2C bus consists of two lines, SDA and SCL. SDA carries data, and the SCL signal provides the clock.
All data is transmitted across the I2C bus in groups of eight bits. To send a bit on the I2C bus, the SDA line
is driven to the appropriate level while SCL is LOW (a LOW on SDA indicates the bit is 0, whereas a
HIGH indicates the bit is 1).
Once the SDA line has settled, the SCL line is brought HIGH, then LOW. This pulse on the SCL line
clocks the SDA bit into the receiver shift register.
The I2C bus is bidirectional: the SDA line is used both for transmitting and receiving data. When a master
reads from a slave, the slave drives the data line; when a master sends to a slave, the master drives the
data line.
Most of the time the bus is idle, no communication is taking place, and both lines are HIGH. When
communication is taking place, the bus is active. Only master devices can start communication on the bus.
Normally, the data line is only allowed to change state while the clock line is LOW. If the data line changes
state while the clock line is HIGH, it is either a START condition or its counterpart, a STOP condition. A
START condition is when the clock line is HIGH and the data line goes from HIGH to LOW. A STOP
condition is when the clock line is HIGH and the data line goes from LOW to HIGH.
After the master issues a START condition, it sends a byte that selects the slave device for
communication. This byte is called the address byte. Each device on an I2C bus has a unique 7-bit
address to which it responds. (Slaves can also have 10-bit addresses; see the I2C specification for
details.) The master sends an address in the address byte, together with a bit that indicates whether it is
to read from or write to the slave device.
Every byte transmitted on the I2C bus, whether it is address or data, is acknowledged with an
acknowledge bit. When a master has finished sending a byte (eight data bits) to a slave, it stops driving
SDA and waits for the slave to acknowledge the byte. The slave acknowledges the byte by pulling SDA
LOW. The master then sends a clock pulse to clock the acknowledge bit. Similarly, a master finishes
reading a byte, then pulls SDA LOW to acknowledge this to the slave, then finally sends a clock pulse to
clock the bit. (Remember that the master always drives the clock line.)
A not-acknowledge is performed simply by leaving SDA HIGH during an acknowledge cycle. If a device is
not present on the bus and the master attempts to address it, it receives a not-acknowledge because no
device is present at that address to pull the line LOW.
When a master has finished communicating with a slave, it may issue a STOP condition. When a STOP
condition is issued, the bus becomes idle again. A master may also issue another START condition. When
a START condition is issued while the bus is active, it is called a repeated START condition.
The TLV320DAC3100-Q1 can also respond to and acknowledge a general call, which consists of the
master issuing a command with a slave address byte of 00h. This feature is disabled by default, but can
be enabled via page 0 / register 34, bit D5.
SCL
SDA
DA(6)
DA(0)
RA(7)
RA(0)
D(7)
D(0)
Slave
Ack
(S)
Slave
Ack
(S)
Slave
Ack
(S)
Start
(M)
7-bit Device Address
(M)
Write
(M)
8-bit Register Address
(M)
8-bit Register Data
(M)
Stop
(M)
(M) => SDA Controlled by Master
(S) => SDA Controlled by Slave
Figure 5-35. I2C Write
60
APPLICATION INFORMATION
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
SCL
SDA
DA(6)
DA(0)
D(7)
D(0)
DA(6)
DA(0)
RA(7)
RA(0)
Master
No Ack
(M)
Start
(M)
Stop
(M)
7-bit Device Address
(M)
Write
(M)
Slave
Ack
(S)
8-bit Register Address
(M)
Slave
Ack
(S)
Repeat
Start
(M)
7-bit Device Address
(M)
Read
(M)
Slave
Ack
(S)
8-bit Register Data
(S)
(M) => SDA Controlled by Master
(S) => SDA Controlled by Slave
Figure 5-36. I2C Read
In the case of an I2C register write, if the master does not issue a STOP condition, then the device enters
auto-increment mode. So in the next eight clocks, the data on SDA is treated as data for the next
incremental register.
Similarly, in the case of an I2C register read, after the device has sent out the 8-bit data from the
addressed register, if the master issues a ACKNOWLEDGE, the slave takes over control of the SDA bus
and transmits for the next eight clocks the data of the next incremental register.
Copyright © 2013, Texas Instruments Incorporated
APPLICATION INFORMATION
61
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
6 REGISTER MAP
6.1 TLV320DAC3100-Q1 Register Map
All features on this device are addressed using the I2C bus. All of the writable registers can be read back.
However, some registers contain status information or data, and are available for reading only.
The TLV320DAC3100-Q1 contains several pages of 8-bit registers, and each page can contain up to 128
registers. The register pages are divided up based on functional blocks for this device. The pages defined
for the TLV320DAC3100-Q1 are 0, 1, 3, 8–9, 12–13 (DAC coefficient pages). Page 0 is the default home
page after RESET. Page control is done by writing a new page value into register 0 of the current page.
The control registers for the TLV320DAC3100-Q1 are described in detail as follows. All registers are 8 bits
in width, with D7 referring to the most-significant bit of each register, and D0 referring to the least-
significant bit.
Pages 0, 1, 3, 8–9, and 12–13 are available for use; however, all other pages and registers are reserved.
Do not read from or write to reserved pages and registers. Also, do not write other than the reset values
for the reserved bits and read-only bits of non-reserved registers; otherwise, device functionality failure
can occur.
Note that the page and register numbers are shown in decimal format. For use in microcode, these
decimal values may require conversion to hexadecimal format. For convienience, the register
numbers are shown in both formats, whereas the page numbers are shown only in decimal format.
Table 6-1. Summary of Register Map
Page Number
Description
0
1
Page 0 is the default page on power up. Configuration for serial interface, digital I/O, and other circuitry.
Configuration for DAC, output drivers, volume controls, and other circuitry.
Register 16 controls the MCLK divider that controls the interrupt pulse duration, debounce timing, and detection-block
clock.
3
8–9
DAC filter and DRC coefficients (buffer A)
DAC filter and DRC coefficients (buffer B)
12–13
6.2 Control Registers, Page 0 (Default Page): Clock Multipliers, Dividers, Serial
Interfaces, Flags, Interrupts, and GPIOs
Page 0 / Register 0 (0x00): Page Control Register
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D0
R/W
0000 0000
0000 0000: Page 0 selected
0000 0001: Page 1 selected
...
1111 1110: Page 254 selected
1111 1111: Page 255 selected
Page 0 / Register 1 (0x01): Software Reset
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D1
D0
R/W
R/W
0000 000
0
Reserved. Write only zeros to these bits.
0: Don't care
1: Self-clearing software reset for control register
Page 0 / Register 2 (0x02): Reserved
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D0
R
XXXX XXXX Reserved. Do not write to this register.
62
REGISTER MAP
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
Page 0 / Register 3 (0x03): OT FLAG
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D2
D1
R
R
XXXX XX
1
Reserved. Do not write to these bits.
0: Overtemperature protection flag (active-low). Valid only if speaker amplifier is powered up
1: Normal operation
D0
R
X
Reserved. Do not write to this bit.
Page 0 / Register 4 (0x04): Clock-Gen Muxing(1)
DESCRIPTION
READ/
WRITE
RESET
VALUE
BIT
D7–D4
D3–D2
R/W
R/W
0000
00
Reserved. Write only zeros to these bits.
00: PLL_CLKIN = MCLK (device pin)
01: PLL_CLKIN = BCLK (device pin)
10: PLL_CLKIN = GPIO1 (device pin)
11: PLL_CLKIN = DIN (can be used for a system where DAC is not used)
D1–D0
R/W
00
00: CODEC_CLKIN = MCLK (device pin)
01: CODEC_CLKIN = BCLK (device pin)
10: CODEC_CLKIN = GPIO1 (device pin)
11: CODEC_CLKIN = PLL_CLK (generated on-chip)
(1) See Section 5.6 for more details on clock-generation mutiplexing and dividers.
Page 0 / Register 5 (0x05): PLL P and R Values
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7
R/W
0
0: PLL is powered down.
1: PLL is powered up.
D6–D4
R/W
001
000: PLL divider P = 8
001: PLL divider P = 1
010: PLL divider P = 2
...
110: PLL divider P = 6
111: PLL divider P = 7
D3–D0
R/W
0001
0000: PLL multiplier R = 16
0001: PLL multiplier R = 1
0010: PLL multiplier R = 2
...
1110: PLL multiplier R = 14
1111: PLL multiplier R = 15
Page 0 / Register 6 (0x06): PLL J Value
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D6
D5–D0
R/W
R/W
00
Reserved. Write only zeros to these bits.
00 0100
00 0000: Do not use (reserved)
00 0001: PLL multiplier J = 1
00 0010: PLL multiplier J = 2
...
11 1110: PLL multiplier J = 62
11 1111: PLL multiplier J = 63
Page 0 / Register 7 (0x07): PLL D-Value MSB(1)
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D6
D5–D0
R/W
R/W
00
Reserved. Write only zeros to these bits.
00 0000
PLL fractional multiplier D-value MSBs D[13:8]
(1) Note that this register is updated only when page 0 / register 8 is written immediately after page 0 / register 7.
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
REGISTER MAP
63
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
Page 0 / Register 8 (0x08): PLL D-Value LSB(1)
DESCRIPTION
READ/
WRITE
RESET
VALUE
BIT
D7–D0
R/W
0000 0000
PLL fractional multiplier D-value LSBs D[7:0]
(1) Note that page 0 / register 8 must be written immediately after page 0 / register 7.
Page 0 / Register 9 (0x09) and Page 0 / Register 10 (0x0B): Reserved
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D0
R
XXXX XXXX Reserved. Do not use.
Page 0 / Register 11 (0x0B): DAC NDAC_VAL
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7
R/W
0
0: DAC NDAC divider is powered down.
1: DAC NDAC divider is powered up.
D6–D0
R/W
000 0001
000 0000: DAC NDAC divider = 128
000 0001: DAC NDAC divider = 1
000 0010: DAC NDAC divider = 2
...
111 1110: DAC NDAC divider = 126
111 1111: DAC NDAC divider = 127
Page 0 / Register 12 (0x0C): DAC MDAC_VAL
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7
R/W
0
0: DAC MDAC divider is powered down.
1: DAC MDAC divider is powered up.
D6–D0
R/W
000 0001
000 0000: DAC MDAC divider = 128
000 0001: DAC MDAC divider = 1
000 0010: DAC MDAC divider = 2
...
111 1110: DAC MDAC divider = 126
111 1111: DAC MDAC divider = 127
Page 0 / Register 13 (0x0D): DAC DOSR_VAL MSB
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D2
D1–D0
R/W
R/W
0000 00
00
Reserved
DAC OSR Value DOSR(9:8)
Page 0 / Register 14 (0x0E): DAC DOSR_VAL LSB(1) (2)
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D0
R/W
1000 0000
DAC OSR Value DOSR(7:0)
0000 0000: DAC OSR(7:0) = 1024 (MSB page 0 / register 13, bits D1–D0 = 00)
0000 0001: Reserved.
0000 0010: DAC OSR(7:0) = 2 (MSB page 0 / register 13, bits D1–D0 = 00)
...
1111 1110: DAC OSR(7:0) = 1022 (MSB page 0 / register 13, bits D1–D0 = 11)
1111 1111: DAC OSR(7:0) = Reserved. Do not use.
(1) DOSR must be a multiple of 2 when using filter type A, a multiple of 4 when using filter type B, and a multiple of 8 when using filter type
C.
(2) Note that page 0 / register 14 must be written to immediately after writing to page 0 / register 13.
Page 0 / Register 15 (0x0F) Through Page 0 / Register 24 (0x18): Reserved
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D0
R/W
XXXX XXXX Reserved. Do not write to these registers.
64
REGISTER MAP
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
Page 0 / Register 25 (0x19): CLKOUT MUX
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D3
D2–D0
R/W
0000 0
000
Reserved
R/W
000: CDIV_CLKIN = MCLK (device pin)
001: CDIV_CLKIN = BCLK (device pin)
010: CDIV_CLKIN = DIN (can be used for systems where the DAC is not required)
011: CDIV_CLKIN = PLL_CLK (generated on-chip)
100: CDIV_CLKIN = DAC_CLK (generated on-chip)
101: CDIV_CLKIN = DAC_MOD_CLK (generated on-chip)
110: Reserved
111: Reserved
Page 0 / Register 26 (0x1A): CLKOUT M_VAL
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7
R/W
0
0: CLKOUT M divider is powered down.
1: CLKOUT M divider is powered up.
D6–D0
R/W
000 0001
000 0000: CLKOUT divider M = 128
000 0001: CLKOUT divider M = 1
000 0010: CLKOUT divider M = 2
...
111 1110: CLKOUT divider M = 126
111 1111: CLKOUT divider M = 127
Page 0 / Register 27 (0x1B): Codec Interface Control 1
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D6
R/W
00
00: Codec interface = I2S
01: Codec Interface = DSP
10: Codec interface = RJF
11: Codec interface = LJF
D5–D4
R/W
00
00: Codec interface word length = 16 bits
01: Codec interface word length = 20 bits
10: Codec interface word length = 24 bits
11: Codec interface word length = 32 bits
D3
D2
R/W
R/W
R/W
0
0
0: BCLK is input.
1: BCLK is output.
0: WCLK is input.
1: WCLK is output.
D1–D0
00
Reserved
Page 0 / Register 28 (0x1C): Data-Slot Offset Programmability
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D0
R/W
0000 0000
Offset (Measured With Respect to WCLK Rising Edge in DSP Mode)
0000 0000: Offset = 0 BCLKs
0000 0001: Offset = 1 BCLK
0000 0010: Offset = 2 BCLKs
...
1111 1110: Offset = 254 BCLKs
1111 1111: Offset = 255 BCLKs
Copyright © 2013, Texas Instruments Incorporated
REGISTER MAP
65
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
Page 0 / Register 29 (0x1D): Codec Interface Control 2
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D4
D3
R/W
R/W
0000
0
Reserved
0: BCLK is not inverted (valid for both primary and secondary BCLK).
1: BCLK is inverted (valid for both primary and secondary BCLK).
D2
R/W
0
BCLK and WCLK Active Even With Codec Powered Down (Valid for Both Primary and Secondary
BCLK)
0: Disabled
1: Enabled
D1–D0
R/W
00
00: BDIV_CLKIN = DAC_CLK (generated on-chip)
01: BDIV_CLKIN = DAC_MOD_CLK (generated on-chip)
10: Reserved
11: Reserved
Page 0 / Register 30 (0x1E): BCLK N_VAL
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7
R/W
0
0: BCLK N-divider is powered down.
1: BCLK N-divider is powered up.
D6–D0
R/W
000 0001
000 0000: BCLK divider N = 128
000 0001: BCLK divider N = 1
000 0010: BCLK divider N = 2
...
111 1110: BCLK divider N = 126
111 1111: BCLK divider N = 127
Page 0 / Register 31 (0x1F): Codec Secondary Interface Control 1
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D5
R/W
R/W
R/W
000
000
00
000: Secondary BCLK is obtained from the GPIO1 pin.
001: Secondary BCLK is not obtained from the GPIO1 pin.
010–111: Reserved
D4–D2
D1–D0
000: Secondary WCLK is obtained from the GPIO1 pin.
001: Secondary WCLK is not obtained from the GPIO1 pin.
010–111: Reserved
00: Secondary DIN is obtained from the GPIO1 pin.
01: Secondary DIN is not obtained from the GPIO1 pin.
10–11: Reserved
Page 0 / Register 32 (0x20): Codec Secondary Interface Control 2
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D4
D3
R/W
R/W
0000
0
Reserved
0: Primary BCLK is fed to codec serial-interface and ClockGen blocks.
1: Secondary BCLK is fed to codec serial-interface and ClockGen blocks.
D2
R/W
0
0: Primary WCLK is fed to codec serial-interface block.
1: Secondary WCLK is fed to codec serial-interface block.
D1
D0
R/W
R/W
0
0
Reserved
0: Primary DIN is fed to codec serial-interface block.
1: Secondary DIN is fed to codec serial-interface block.
66
REGISTER MAP
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
Page 0 / Register 33 (0x21): Codec Secondary Interface Control 3
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7
R/W
0
0: Primary BCLK output = internally generated BCLK clock
1: Primary BCLK output = secondary BCLK
D6
R/W
R/W
0
0: Secondary BCLK output = primary BCLK
1: Secondary BCLK output = internally generated BCLK clock
D5–D4
00
00: Primary WCLK output = internally generated DAC_fS
01: Reserved
10: Primary WCLK output = secondary WCLK
11: Reserved
D3–D2
D1–D0
R/W
R/W
00
00
00: Secondary WCLK output = primary WCLK
01: Secondary WCLK output = internally generated DAC_fS clock
10: Reserved
11: Reserved
Reserved
Page 0 / Register 34 (0x22): I2C Bus Condition
DESCRIPTION
READ/
WRITE
RESET
VALUE
BIT
D7–D6
D5
R/W
R/W
00
0
Reserved. Write only the reset value to these bits.
0: I2C general-call address is ignored.
1: Device accepts I2C general-call address.
D4–D0
R/W
0 0000
Reserved. Write only zeros to these bits.
Page 0 / Register 35 (0x23) and Page 0 / Register 36 (0x24): Reserved
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D0
R
XXXX XXXX Reserved. Do not use.
Page 0 / Register 37 (0x25): DAC Flag Register
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7
R
0
0: Left-channel DAC powered down
1: Left-channel DAC powered up
D6
D5
R
R
X
0
Reserved
0: HPL driver powered down
1: HPL driver powered up
D4
D3
R
R
0
0
0: Left-channel class-D driver powered down
1: Left-channel class-D driver powered up
0: Right-channel DAC powered down
1: Right-channel DAC powered up
D2
D1
R
R
X
0
Reserved
0: HPR driver powered down
1: HPR driver powered up
D0
R
0
0: Right-channel class-D driver powered down
1: Right-channel class-D driver powered up
Page 0 / Register 38 (0x26): DAC Flag Register
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D5
D4
R
R
XXX
0
Reserved
0: Left-channel DAC PGA applied gain ≠ programmed gain
1: Left-channel DAC PGA applied gain = programmed gain
D3–D1
D0
R
R
XXX
0
Reserved
0: Right-channel DAC PGA applied gain ≠ programmed gain
1: Right-channel DAC PGA applied gain = programmed gain
Copyright © 2013, Texas Instruments Incorporated
REGISTER MAP
67
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
Page 0 / Register 39 (0x27): Overflow Flags
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7(1)
R
R
R
R
0
Left-Channel DAC Overflow Flag
0: Overflow has not occurred.
1: Overflow has occurred.
D6(1)
D5(1)
0
0
Right-Channel DAC Overflow Flag
0: Overflow has not occurred.
1: Overflow has occurred.
DAC Barrel Shifter Output Overflow Flag
0: Overflow has not occurred.
1: Overflow has occurred.
D4–D0
0 0000
Reserved
(1) Sticky flag bits. These are read-only bits. They are automatically cleared once they are read and are set only if the source trigger occurs
again.
Page 0 / Register 40 (0x28) Through Page 0 / Register 43 (0x2B): Reserved
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D0
R
XXXX XXXX Reserved. Do not use.
Page 0 / Register 44 (0x2C): DAC Interrupt Flags (Sticky Bits)
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7(1)
R
R
R
R
R
R
R
0
0: No short circuit is detected at HPL/left class-D driver.
1: Short circuit is detected at HPL/left class-D driver.
D6(1)
D5(1)
D4(1)
D3(1)
D2(1)
D1–D0
0
0: No short circuit is detected at HPR/right class-D driver.
1: Short circuit is detected at HPR/right class-D driver.
X
X
0
0: No headset button pressed
1: Headset button pressed
0: No headset insertion/removal is detected.
1: Headset insertion/removal is detected.
0: Left DAC signal power is ≤ the signal threshold of DRC.
1: Left DAC signal power is > the signal threshold of DRC.
0
0: Right DAC signal power is ≤ the signal threshold of DRC.
1: Right DAC signal power is > the signal threshold of DRC.
00
Reserved
(1) Sticky flag bits. These are read-only bits. They are automatically cleared once they are read and are set only if the source trigger occurs
again.
Page 0 / Register 45 (0x2D): Reserved
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D0
R
0000 0000 Reserved. Do not use.
68
REGISTER MAP
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
Page 0 / Register 46 (0x2E): DAC Interrupt Flags
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7
R
0
0: No short circuit detected at HPL/left class-D driver
1: Short circuit detected at HPL/left class-D driver
D6
D5
R
R
R
R
R
R
0
0: No short circuit detected at HPR/right class-D driver
1: Short circuit detected at HPR/right class-D driver
X
X
0
0: No headset button pressed
1: Headset button pressed
D4
0: Headset removal detected
1: Headset insertion detected
D3
0: Left DAC signal power is ≤ the signal threshold of the DRC.
1: Left DAC signal power is > the signal threshold of the DRC.
D2
0
0: Right DAC signal power is ≤ the signal threshold of the DRC.
1: Right DAC signal power is > the signal threshold of the DRC.
D1–D0
00
Reserved
Page 0 / Register 47 (0x2F): Reserved
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D0
R/W
0000 0000 Reserved. Write only the reset value to these bits.
Page 0 / Register 48 (0x30): INT1 Control Register
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7
R/W
R/W
R/W
0
0
0
0: Headset-insertion detect interrupt is not used in the generation of INT1 interrupt.
1: Headset-insertion detect interrupt is used in the generation of INT1 interrupt.
D6
D5
0: Button-press detect interrupt is not used in the generation of INT1 interrupt.
1: Button-press detect interrupt is used in the generation of INT1 interrupt.
0: DAC DRC signal-power interrupt is not used in the generation of INT1 interrupt.
1: DAC DRC signal-power interrupt is used in the generation of INT1 interrupt.
D4
D3
R/W
R/W
0
0
Reserved
0: Short-circuit interrupt is not used in the generation of INT1 interrupt.
1: Short-circuit interrupt is used in the generation of INT1 interrupt.
D2
R/W
0
0: DAC data overflow does not result in an INT1 interrupt.
1: DAC data overflow results in an INT1 interrupt.
D1
D0
R/W
R/W
0
0
Reserved
0: INT1 is only one pulse (active-high) of typical 2-ms duration.
1: INT1 is multiple pulses (active-high) of typical 2-ms duration and 4-ms period, until page 0 /
register 44 is read by the user.
Page 0 / Register 49 (0x31): INT2 Control Register
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7
R/W
R/W
R/W
0
0
0
0: Headset-insertion detect interrupt is not used in the generation of INT2 interrupt.
1: Headset-insertion detect interrupt is used in the generation of INT2 interrupt.
D6
D5
0: Button-press detect interrupt is not used in the generation of INT2 interrupt.
1: Button-press detect interrupt is used in the generation of INT2 interrupt.
0: DAC DRC signal-power interrupt is not used in the generation of INT2 interrupt.
1: DAC DRC signal-power interrupt is used in the generation of INT2 interrupt.
D4
D3
R/W
R/W
0
0
Reserved
0: Short-circuit interrupt is not used in the generation of INT2 interrupt.
1: Short-circuit interrupt is used in the generation of INT2 interrupt.
D2
R/W
0
0: DAC data overflow does not result in an INT2 interrupt.
1: DAC data overflow results in an INT2 interrupt.
D1
D0
R/W
R/W
0
0
Reserved
0: INT2 is only one pulse (active-high) of typical 2-ms duration.
1: INT2 is multiple pulses (active-high) of typical 2-ms duration and 4-ms period, until page 0 /
register 44 is read by the user.
Copyright © 2013, Texas Instruments Incorporated
REGISTER MAP
69
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
Page 0 / Register 50 (0x32): Reserved
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7-D0
R
0000 0000 Reserved. Do not use.
Page 0 / Register 51 (0x33): GPIO1 In/Out Pin Control
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D6
D5–D2
R/W
R/W
XX
Reserved. Do not write any value other than reset value.
0000
0000: GPIO1 disabled (input and output buffers powered down)
0001: GPIO1 is in input mode (can be used as secondary BCLK input, secondary WCLK input,
secondary DIN input, or in ClockGen block).
0010: GPIO1 is used as general-purpose input (GPI).
0011: GPIO1 output = general-purpose output
0100: GPIO1 output = CLKOUT output
0101: GPIO1 output = INT1 output
0110: GPIO1 output = INT2 output
0111: Reserved
1000: GPIO1 output = secondary BCLK output for codec interface
1001: GPIO1 output = secondary WCLK output for codec interface
1010–1111: Reserved
D1
D0
R
X
0
GPIO1 input buffer value
R/W
0: GPIO1 general-purpose output value = 0
1: GPIO1 general-purpose output value = 1
Page 0 / Register 52 (0x34): Reserved
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D0
R
XXXX XXXX Reserved. Do not use.
Page 0 / Register 53 (0x35): Reserved
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D0
R
0000 0000 Reserved
Page 0 / Register 54 (0x36): DIN (IN Pin) Control
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D3
D2–D1
R/W
R/W
0000 0
01
Reserved
00: DIN disabled (input buffer powered down)
01: DIN enabled (can be used as DIN for codec interface or into ClockGen block)
10: DIN is used as general-purpose input (GPI)
11: Reserved
D0
R
X
DIN input-buffer value
Page 0 / Register 55 (0x37) Through Page 0 / Register 59 (0x3B): Reserved
READ/
WRITE
RESET
BIT
DESCRIPTION
VALUE
D7–D0
R
XXXX XXXX Reserved. Do not write to these bits.
70
REGISTER MAP
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
Page 0 / Register 60 (0x3C): DAC Processing Block Selection
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D5
D4–D0
R/W
000
Reserved. Write only default value.
0 0000: Reserved. Do not use.
R/W
0 0001
0 0001: DAC signal processing block PRB_P1
0 0010: DAC signal processing block PRB_P2
0 0011: DAC signal processing block PRB_P3
0 0100: DAC signal processing block PRB_P4
...
1 1000: DAC signal processing block PRB_P24
1 1001: DAC signal processing block PRB_P25
1 1010–1 1111: Reserved. Do not use.
Page 0 / Register 61 (0x3D) Through Page 0 / Register 62: Reserved
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D0
R
XXXX XXXX Reserved. Do not write.
Page 0 / Register 63 (0x3F): DAC Data-Path Setup
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7
R/W
R/W
R/W
0
0: Left-channel DAC is powered down.
1: Left-channel DAC is powered up.
D6
0
0: Right-channel DAC is powered down.
1: Right-channel DAC is powered up.
D5–D4
01
00: Left-channel DAC data path = off
01: Left-channel DAC data path = left data
10: Left-channel DAC data path = right data
11: Left-channel DAC data path = left-channel and right-channel data [(L + R)/2]
D3–D2
D1–D0
R/W
R/W
01
00
00: Right-channel DAC data path = off
01: Right-channel DAC data path = right data
10: Right-channel DAC data path = left data
11: Right-channel DAC data path = left-channel and right-channel data [(L + R)/2]
00: DAC channel volume control soft-stepping is enabled for one step per sample period.
01: DAC channel volume control soft-stepping is enabled for one step per two sample periods.
10: DAC channel volume control soft-stepping is disabled.
11: Reserved. Do not write this sequence to these bits.
Page 0 / Register 64 (0x40): DAC VOLUME CONTROL
DESCRIPTION
READ/
WRITE
RESET
VALUE
BIT
D7–D4
D3
R/W
R/W
0000
1
Reserved. Write only zeros to these bits.
0: Left-channel DAC not muted
1: Left-channel DAC muted
D2
R/W
R/W
1
0: Right-channel DAC not muted
1: Right-channel DAC muted
D1–D0(
00
00: Left and right channels have independent volume control.
01: Left-channel volume control is the programmed value of right-channel volume control.
10: Right-channel volume control is the programmed value of left-channel volume control.
11: Same as 00
1)
(1) When DRC is enabled, left and right channel volume controls are always independent. Program bits D1–D0 to 00.
Copyright © 2013, Texas Instruments Incorporated
REGISTER MAP
71
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
Page 0 / Register 65 (0x41): DAC Left Volume Control
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D0
R/W
0000 0000
Left DAC Channel Digital Volume Control Setting
0111 1111–0011 0001: Reserved. Do not use
0011 0000: Digital volume control = 24 dB
0010 1111: Digital volume control = 23.5 dB
0010 1110: Digital volume control = 23 dB
...
0000 0001: Digital volume control = 0.5 dB
0000 0000: Digital volume control = 0 dB
1111 1111: Digital volume control = –0.5 dB
...
1000 0010: Digital volume control = –63 dB
1000 0001: Digital volume control = –63.5 dB
1000 0000: Reserved
Page 0 / Register 66 (0x42): DAC Right Volume Control
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D0
R/W
0000 0000
Right DAC Channel Digital Volume Control Setting
0111 1111–0011 0001: Reserved. Do not use
0011 0000: Digital volume control = 24 dB
0010 1111: Digital volume control = 23.5 dB
0010 1110: Digital volume control = 23 dB
...
0000 0001: Digital volume control = 0.5 dB
0000 0000: Digital volume control = 0 dB
1111 1111: Digital volume control = –0.5 dB
...
1000 0010: Digital volume control = –63 dB
1000 0001: Digital volume control = –63.5 dB
1000 0000: Reserved
Page 0 / Register 67 (0x43): Headset Detection
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7
R/W
0
0: Headset detection disabled
1: Headset detection enabled
D6–D5
D4–D2
R
XX
00: No headset detected
01: Headset without microphone is detected
10: Reserved
11: Headset with microphone is detected
R/W
000
Debounce Programming for Glitch Rejection During Headset Detection(1)
000: 16 ms (sampled with 2-ms clock)
001: 32 ms (sampled with 4-ms clock)
010: 64 ms (sampled with 8-ms clock)
011: 128 ms (sampled with 16-ms clock)
100: 256 ms (sampled with 32-ms clock)
101: 512 ms (sampled with 64-ms clock)
110: Reserved
111: Reserved
D1–D0
R/W
00
Debounce Programming for Glitch Rejection During Headset Button-Press Detection
00: 0 ms
01: 8 ms (sampled with 1-ms clock)
10: 16 ms (sampled with 2-ms clock)
11: 32 ms (sampled with 4-ms clock)
(1) Note that these times are generated using the 1-MHz reference clock which is defined in page 3 / register 16.
72
REGISTER MAP
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
Page 0 / Register 68 (0x44): DRC Control 1
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7
D6
R/W
0
0
Reserved. Write only the reset value to these bits.
R/W
0: DRC disabled for left channel
1: DRC enabled for left channel
D5
R/W
R/W
0
0: DRC disabled for right channel
1: DRC enabled for right channel
D4–D2
011
000: DRC threshold = –3 dB
001: DRC threshold = –6 dB
010: DRC threshold = –9 dB
011: DRC threshold = –12 dB
100: DRC threshold = –15 dB
101: DRC threshold = –18 dB
110: DRC threshold = –21 dB
111: DRC threshold = –24 dB
D1–D0
R/W
11
00: DRC hysteresis = 0 dB
01: DRC hysteresis = 1 dB
10: DRC hysteresis = 2 dB
11: DRC hysteresis = 3 dB
Page 0 / Register 69 (0x45): DRC Control 2
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7
R
0
Reserved. Write only the reset value to these bits.
D6–D3
R/W
0111
DRC Hold Time
0000: DRC Hold Disabled
0001: DRC Hold Time = 32 DAC Word Clocks
0010: DRC Hold Time = 64 DAC Word Clocks
0011: DRC Hold Time = 128 DAC Word Clocks
0100: DRC Hold Time = 256 DAC Word Clocks
0101: DRC Hold Time = 512 DAC Word Clocks
0110: DRC Hold Time = 1024 DAC Word Clocks
0111: DRC Hold Time = 2048 DAC Word Clocks
1000: DRC Hold Time = 4096 DAC Word Clocks
1001: DRC Hold Time = 8192 DAC Word Clocks
1010: DRC Hold Time = 16 384 DAC Word Clocks
1011: DRC Hold Time = 32 768 DAC Word Clocks
1100: DRC Hold Time = 65 536 DAC Word Clocks
1101: DRC Hold Time = 98 304 DAC Word Clocks
1110: DRC Hold Time = 131 072 DAC Word Clocks
1111: DRC Hold Time = 163 840 DAC Word Clocks
D2–D0
R
000
Reserved. Write only the reset value to these bits.
Copyright © 2013, Texas Instruments Incorporated
REGISTER MAP
73
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
Page 0 / Register 70 (0x46): DRC Control 3
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D4
R/W
0000
Value: DRC Attack Rate (AR) per sample period
0000: DRC attack rate = 4 dB (AR), or 4 db per sample time (tS)
0001: DRC attack rate = AR / 2 dB
0010: DRC attack rate = AR / 22 dB
0011: DRC attack rate = AR / 23 dB
0100: DRC attack rate = AR / 24 dB
0101: DRC attack rate = AR / 25 dB
0110: DRC attack rate = AR / 26 dB
0111: DRC attack rate = AR / 27 dB
1000: DRC attack rate = AR / 28 dB
1001: DRC attack rate = AR / 29 dB
1010: DRC attack rate = AR / 210 dB
1011: DRC attack rate = AR / 211 dB
1100: DRC attack rate = AR / 212 dB
1101: DRC attack rate = AR / 213 dB
1110: DRC attack rate = AR / 214 dB
1111: DRC attack rate = AR / 215 dB
D3–D0
R/W
0000
Decay Rate is defined as DR / 2[bits D3-D0 value] dB per DAC Word Clock, where DR = 0.015625 dB
0000: DRC decay rate (DR) = 0.015625 dB per DAC Word Clock
0001: DRC decay rate = DR / 2 dB per DAC Word Clock
0010: DRC decay rate = DR / 22 dB per DAC Word Clock
0011: DRC decay rate = DR / 23 dB per DAC Word Clock
0100: DRC decay rate = DR / 24 dB per DAC Word Clock
0101: DRC decay rate = DR / 25 dB per DAC Word Clock
0110: DRC decay rate = DR / 26 dB per DAC Word Clock
0111: DRC decay rate = DR / 27 dB per DAC Word Clock
1000: DRC decay rate = DR / 28 dB per DAC Word Clock
1001: DRC decay rate = DR / 29 dB per DAC Word Clock
1010: DRC decay rate = DR / 210 dB per DAC Word Clock
1011: DRC decay rate = DR / 211 dB per DAC Word Clock
1100: DRC decay rate = DR / 212 dB per DAC Word Clock
1101: DRC decay rate = DR / 213 dB per DAC Word Clock
1110: DRC decay rate = DR / 214 dB per DAC Word Clock
1111: DRC decay rate = DR / 215 dB per DAC Word Clock
(1)
Page 0 / Register 71 (0x47): Left Beep Generator
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7
R/W
0
0: Beep generator is disabled.
1: Beep generator is enabled (self-clearing based on beep duration).
D6
R/W
R/W
0
Reserved. Write only reset value.
D5–D0
00 0000
00 0000: Left-channel beep volume control = 2 dB
00 0001: Left-channel beep volume control = 1 dB
00 0010: Left-channel beep volume control = 0 dB
00 0011: Left-channel beep volume control = –1 dB
...
11 1110: Left-channel beep volume control = –60 dB
11 1111: Left-channel beep volume control = –61 dB
(1) The beep generator is only available in PRB_P25 DAC processing mode.
74
REGISTER MAP
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
Page 0 / Register 72 (0x48): Right Beep Generator(1)
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D6
R/W
00
00: Left and right channels have independent beep volume control.
01: Left-channel beep volume control is the programmed value of right-channel beep volume control.
10: Right-channel beep volume control is the programmed value of left-channel beep volume control.
11: Same as 00
D5–D0
R/W
00 0000
00 0000: Right-channel beep volume control = 2 dB
00 0001: Right-channel beep volume control = 1 dB
00 0010: Right-channel beep volume control = 0 dB
00 0011: Right-channel beep volume control = –1 dB
...
11 1110: Right-channel beep volume control = –60 dB
11 1111: Right-channel beep volume control = –61 dB
(1) The beep generator is only available in PRB_P25 DAC processing mode.
Page 0 / Register 73 (0x49): Beep Length MSB
DESCRIPTION
READ/
WRITE
RESET
VALUE
BIT
D7–D0
R/W
0000 0000
8 MSBs out of 24 bits for the number of samples for which the beep must be generated.
Page 0 / Register 74 (0x4A): Beep Length Middle Bits
DESCRIPTION
READ/
WRITE
RESET
VALUE
BIT
D7–D0
R/W
0000 0000
8 middle bits out of 24 bits for the number of samples for which the beep must be generated.
Page 0 / Register 75 (0x4B): Beep Length LSB
DESCRIPTION
READ/
WRITE
RESET
VALUE
BIT
D7–D0
R/W
1110 1110
8 LSBs out of 24 bits for the number of samples for which beep need to be generated.
Page 0 / Register 76 (0x4C): Beep Sin(x) MSB
DESCRIPTION
READ/
WRITE
RESET
VALUE
BIT
D7–D0
R/W
0001 0000
8 MSBs out of 16 bits for sin(2π × fin/fS), where fin is the beep frequency and fS is the DAC sample rate.
Page 0 / Register 77 (0x4D): Beep Sin(x) LSB
DESCRIPTION
READ/
WRITE
RESET
VALUE
BIT
D7–D0
R/W
1101 1000
8 LSBs out of 16 bits for sin(2π × fin/fS), where fin is the beep frequency and fS is the DAC sample rate.
Page 0 / Register 78 (0x4E): Beep Cos(x) MSB
DESCRIPTION
READ/
WRITE
RESET
VALUE
BIT
D7–D0
R/W
0111 1110
8 MSBs out of 16 bits for cos(2π × fin/fS), where fin is the beep frequency and fS is the DAC sample rate.
Page 0 / Register 79 (0x4F): Beep Cos(x) LSB
DESCRIPTION
READ/
WRITE
RESET
VALUE
BIT
D7–D0
R/W
1110 0011
8 LSBs out of 16 bits for cos(2π × fin/fS), where fin is the beep frequency and fS is the DAC sample rate.
Page 0 / Register 80 (0x50) Through Page 0 / Register 115 (0x73): Reserved
READ/
WRITE
RESET
BIT
DESCRIPTION
VALUE
D7–D0
R
XXXX XXXX Reserved. Do not use.
Copyright © 2013, Texas Instruments Incorporated
REGISTER MAP
75
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
Page 0 / Register 116 (0x74): VOL/MICDET-Pin SAR ADC – Volume Control
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7
R/W
R/W
R/W
0
0: DAC volume control is controlled by control register (7-bit Vol ADC is powered down).
1: DAC volume control is controlled by pin.
D6
0
0: Internal on-chip RC oscillator is used for the 7-bit Vol ADC for pin volume control.
1: MCLK is used for the 7-bit Vol ADC for pin volume control.
D5–D4
00
00: No hysteresis for volume control ADC output
01: Hysteresis of ±1 bit
10: Hysteresis of ±2 bits
11: Reserved. Do not write this sequence to these bits.
D3
R/W
R/W
0
Reserved. Write only reset value.
D2–D0
000
Throughput of the 7-bit Vol ADC for pin volume control, frequency based on MCLK or internal oscillator.
MCLK = 12 MHz
Internal Oscillator Source
000: Throughput =
001: Throughput =
010: Throughput =
011: Throughput =
100: Throughput =
101: Throughput =
110: Throughput =
111: Throughput =
15.625 Hz
31.25 Hz
62.5 Hz
125 Hz
250 Hz
500 Hz
1 kHz
10.68 Hz
21.35 Hz
42.71 Hz
8.2 Hz
170 Hz
340 Hz
680 Hz
1.37 kHz
2 kHz
Note: These values are based on a nominal oscillator
frequency of 8.2 MHz. The values scale according to
the actual oscillator frequency.
Page 0 / Register 117 (0x75): VOL/MICDET-Pin Gain
DESCRIPTION
READ/
WRITE
RESET
VALUE
BIT
D7
R
R
0
Reserved. Write only zero to this bit.
D6–D0
XXX XXXX 000 0000: Gain applied by pin volume control = 18 dB
000 0001: Gain applied by pin volume control = 17.5 dB
000 0010: Gain applied by pin volume control = 17 dB
...
010 0011: Gain applied by pin volume control = 0.5 dB
010 0100: Gain applied by pin volume control = 0 dB
010 0101: Gain applied by pin volume control = –0.5 dB
...
101 1001: Gain applied by pin volume control = –26.5 dB
101 1010: Gain applied by pin volume control = –27 dB
101 1011: Gain applied by pin volume control = –28 dB
...
111 1101: Gain applied by pin volume control = –62 dB
111 1110: Gain applied by pin volume control = –63 dB
111 1111: Reserved
Page 0 / Register 118 (0x76) Through Page 0 / Register 127 (0x7F): Reserved
READ/
WRITE
RESET
BIT
DESCRIPTION
VALUE
D7–D0
R
XXXX XXXX Reserved. Do not use.
6.3 Control Registers, Page 1: DAC, Power-Controls and MISC Logic-Related
Programmabilities
Page 1 / Register 0 (0x00): Page Control Register
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D0
R/W
0000 0000
0000 0000: Page 0 selected
0000 0001: Page 1 selected
...
1111 1110: Page 254 selected
1111 1111: Page 255 selected
76
REGISTER MAP
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
Page 1 / Register 1 (0x01) Through Page 1 / Register 29 (0x1D): Reserved
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D0
R
XXXX XXXX Reserved. Do not use.
Page 1 / Register 30 (0x1E): Headphone and Speaker Amplifier Error Control
READ/
WRITE
RESET
BIT
DESCRIPTION
VALUE
D7–D2
D1
R/W
R/W
0000 00
0
Reserved
0: Reset SPL and SPR power-up control bits on short-circuit detection
1: SPL and SPR power-up control bits remain unchanged on short-circuit detection
D0
R/W
0
0: Reset HPL and HPR power-up control bits on short-circuit detection.
1: HPL and HPR power-up control bits remain unchanged on short-circuit detection
Page 1 / Register 31 (0x1F): Headphone Drivers
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7
R/W
0
0: HPL output driver is powered down.
1: HPL output driver is powered up.
D6
R/W
0
0: HPR output driver is powered down.
1: HPR output driver is powered up.
D5
R/W
R/W
0
0
Reserved. Write only zero to this bit.
D4–D3
00: Output common-mode voltage = 1.35 V
01: Output common-mode voltage = 1.5 V
10: Output common-mode voltage = 1.65 V
11: Output common-mode voltage = 1.8 V
D2
D1
R/W
R/W
1
0
Reserved. Write only 1 to this bit.
0: If short-circuit protection is enabled for headphone driver and short circuit is detected, device limits
the
the maximum current to the load.
1: If short-circuit protection is enabled for headphone driver and short circuit is detected, device powers
down the output driver.
D0
R
0
0: Short circuit is not detected on the headphone driver.
1: Short circuit is detected on the headphone driver.
Page 1 / Register 32 (0x20): Class-D Speaker Amplifier
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7
R/W
0
0: Class-D output driver is powered down.
1: Class-D output driver is powered up.
D6–D1
D0
R/W
R
000 011
0
Reserved. Write only the reset value to these bits.
0: Short circuit is not detected on the class-D driver. Valid only if class-D amplifier is powered up. For
short-circuit flag sticky bit, see page 0 / register 44.
1: Short circuit is detected on the class-D driver. Valid only if class-D amplifier is powered up. For short-
circuit flag sticky bit, see page 0 / register 44.
Copyright © 2013, Texas Instruments Incorporated
REGISTER MAP
77
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
Page 1 / Register 33 (0x21): HP Output Drivers POP Removal Settings
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7
R/W
0
0: If power-down sequence is activated by device software, power down using page 1 / register 46,
bit D7, then power down the DAC simultaneously with the HP and SP amplifiers.
1: If power-down sequence is activated by device software, power down using page 1 / register 46,
bit D7, then power down DAC only after HP and SP amplifiers are completely powered down. This is
to optimize power-down POP.
D6–D3
R/W
0111
0000: Driver power-on time = 0 μs
0001: Driver power-on time = 15.3 μs
0010: Driver power-on time = 153 μs
0011: Driver power-on time = 1.53 ms
0100: Driver power-on time = 15.3 ms
0101: Driver power-on time = 76.2 ms
0110: Driver power-on time = 153 ms
0111: Driver power-on time = 304 ms
1000: Driver power-on time = 610 ms
1001: Driver power-on time = 1.22 s
1010: Driver power-on time = 3.04 s
1011: Driver power-on time = 6.1 s
1100–1111: Reserved. Do not write these sequences to these bits.
NOTE: These values are based on typical oscillator frequency of 8.2 MHz. Scale according to the actual
oscillator frequency.
D2–D1
R/W
R/W
11
0
00: Driver ramp-up step time = 0 ms
01: Driver ramp-up step time = 0.98 ms
10: Driver ramp-up step time = 1.95 ms
11: Driver ramp-up step time = 3.9 ms
NOTE: These values are based on typical oscillator frequency of 8.2 MHz. Scale according to the actual
oscillator frequency.
D0
0: Weakly driven output common-mode voltage is generated from resistor divider of the AVDD supply.
1: Reserved.
Page 1 / Register 34 (0x22): Output Driver PGA Ramp-Down Period Control
READ/
WRITE
RESET
BIT
DESCRIPTION
VALUE
D7
R/W
R/W
0
Reserved. Write only the reset value to this bit.
D6–D4
000
Speaker Power-Up Wait Time (Duration Based on Using Internal Oscillator)
000: Wait time = 0 ms
001: Wait time = 3.04 ms
010: Wait time = 7.62 ms
011: Wait time = 12.2 ms
100: Wait time = 15.3 ms
101: Wait time = 19.8 ms
110: Wait time = 24.4 ms
111: Wait time = 30.5 ms
NOTE: These values are based on typical oscillator frequency of 8.2 MHz. The values scale according
to the actual oscillator frequency.
D3–D0
R/W
0000
Reserved. Write only the reset value to these bits.
78
REGISTER MAP
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
Page 1 / Register 35 (0x23): DAC_L and DAC_R Output Mixer Routing
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D6
R/W
00
00: DAC_L is not routed anywhere.
01: DAC_L is routed to the left-channel mixer amplifier.
10: DAC_L is routed directly to the HPL driver.
11: Reserved
D5
D4
R/W
R/W
0
0
0: AIN1 input is not routed to the left-channel mixer amplifier.
1: AIN1 input is routed to the left-channel mixer amplifier.
0: AIN2 input is not routed to the left-channel mixer amplifier.
1: AIN2 input is routed to the left-channel mixer amplifier.
D3–D2
00
00: DAC_R is not routed anywhere.
01: DAC_R is routed to the right-channel mixer amplifier.
10: DAC_R is routed directly to the HPR driver.
11: Reserved
D1
D0
R/W
R/W
0
0
0: AIN2 input is not routed to the right-channel mixer amplifier.
1: AIN2 input is routed to the right-channel mixer amplifier.
0: HPL driver output is not routed to the HPR driver.
1: HPL driver output is routed to the HPR driver input (used for differential output mode).
Page 1 / Register 36 (0x24): Left Analog Vol to HPL
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7
R/W
0
0: Left-channel analog volume control is not routed to HPL output driver.
1: Left-channel analog volume control is routed to HPL output driver.
D6–D0
R/W
111 1111
Left-channel analog volume control gain (non-linear) for the HPL output driver, 0 dB to –78 dB. See
Table 5-24.
Page 1 / Register 37 (0x25): Right Analog Vol to HPR
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7
R/W
0
0: Right-channel analog volume control is not routed to HPR output driver.
1: Right-channel analog volume control is routed to HPR output driver.
D6–D0
R/W
111 1111
Right-channel analog volume control gain (non-linear) for the HPR output driver, 0 dB to –78 dB. See
Table 5-24.
Page 1 / Register 38 (0x26): Left Analog Vol to SPK
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7
R/W
0
0: Left-channel analog volume control output is not routed to class-D output driver.
1: Left-channel analog volume control output is routed to class-D output driver.
D6–D0
R/W
111 1111
Left-channel analog volume control output gain (non-linear) for the class-D output driver, 0 dB to –78
dB. See Table 5-24.
Page 1 / Register 39 (0x27): Reserved
DESCRIPTION
READ/
WRITE
RESET
VALUE
BIT
D7–D0
R
0111 1111
Reserved. Do not use.
Copyright © 2013, Texas Instruments Incorporated
REGISTER MAP
79
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
Page 1 / Register 40 (0x28): HPL Driver
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7
R/W
R/W
0
Reserved. Write only zero to this bit.
D6–D3
0000
0000: HPL driver PGA = 0 dB
0001: HPL driver PGA = 1 dB
0010: HPL driver PGA = 2 dB
...
1000: HPL driver PGA = 8 dB
1001: HPL driver PGA = 9 dB
1010–1111: Reserved. Do not write these sequences to these bits.
D2
D1
D0
R/W
R/W
R
0
1
0
0: HPL driver is muted.
1: HPL driver is not muted.
0: HPL driver is weakly driven to a common mode during power down.(1)
1: HPL driver is high-impedance during power down.
0: Not all programmed gains to HPL have been applied yet.
1: All programmed gains to HPL have been applied.
(1) If D1 is programmed as 0, Page 1 / Register 33 D0 must be set to 0.
Page 1 / Register 41 (0x29): HPR Driver
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7
R/W
R/W
0
Reserved. Write only zero to this bit.
D6–D3
0000
0000: HPR driver PGA = 0 dB
0001: HPR driver PGA = 1 dB
0010: HPR driver PGA = 2 dB
...
1000: HPR driver PGA = 8 dB
1001: HPR driver PGA = 9 dB
1010–1111: Reserved. Do not write these sequences to these bits.
D2
D1
D0
R/W
R/W
R
0
1
0
0: HPR driver is muted.
1: HPR driver is not muted.
0: HPR driver is weakly driven to a common mode during power down.(1)
1: HPR driver is high-impedance during power down.
0: Not all programmed gains to HPR have been applied yet.
1: All programmed gains to HPR have been applied.
(1) If D1 is programmed as 0, Page 1 / Register 33 D0 must be set to 0.
Page 1 / Register 42 (0x2A): Class-D Speaker (SPK) Driver
DESCRIPTION
READ/
WRITE
RESET
VALUE
BIT
D7–D5
D4–D3
R/W
R/W
000
00
Reserved. Write only zeros to these bits.
00: Cass-D driver output stage gain = 6 dB
01: Class-D driver output stage gain = 12 dB
10: Class-D driver output stage gain = 18 dB
11: Class-D driver output stage gain = 24 dB
D2
R/W
0
0: Class-D driver is muted.
1: Class-D driver is not muted.
D1
D0
R/W
R
0
0
Reserved. Write only zero to this bit.
0: Not all programmed gains to class-D driver have been applied yet.
1: All programmed gains to class-D driver have been applied.
Page 1 / Register 43 (0x2B): Reserved
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D0
R
0000 0000 Reserved. Do not use.
80
REGISTER MAP
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
Page 1 / Register 44 (0x2C): HP Driver Control
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D5
R/W
000
Debounce Time for Headset Short-Circuit Detection
MCLK/DIV (Page 3 /
register 16) = 1-MHz Internal Oscillator Source
Source
(1)
000: Debounce time =
001: Debounce time =
010: Debounce time =
011: Debounce time =
100: Debounce time =
101: Debounce time =
110: Debounce time =
111: Debounce time =
0 μs
8 μs
0 μs
7.8 μs
15.6 μs
31.2 μs
62.4 μs
124.9 μs
250 μs
500 μs
16 μs
32 μs
64 μs
128 μs
256 μs
512 μs
Note: These values are based on a nominal oscillator
frequency of 8.2 MHz. The values scale according to
the actual oscillator frequency.
D4–D3
R/W
00
00: Default mode for the DAC
01: DAC performance increased by increasing the current
10: Reserved
11: DAC performance increased further by increasing the current again
D2
D1
D0
R/W
R/W
R/W
0
0
0
0: HPL output driver is programmed as headphone driver.
1: HPL output driver is programmed as lineout driver.
0: HPR output driver is programmed as headphone driver.
1: HPR output driver is programmed as lineout driver.
Reserved. Write only zero to this bit.
(1) The clock used for the debounce has a clock period = debounce duration/8.
Page 1 / Register 45 (0x2D): Reserved
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D0
R/W
XXXX XXXX Reserved. Do not write to this register.
Page 1 / Register 46 (0x2E): MICBIAS
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7
R/W
0
0: Device software power down is not enabled.
1: Device software power down is enabled.
Reserved. Write only zeros to these bits.
D6–D4
D3
R/W
R/W
000
0
0: Programmed MICBIAS is not powered up if headset detection is enabled but headset is not inserted.
1: Programmed MICBIAS is powered up even if headset is not inserted.
D2
R/W
R/W
0
Reserved. Write only zero to this bit.
D1–D0
00
00: MICBIAS output is powered down.
01: MICBIAS output is powered to 2 V.
10: MICBIAS output is powered to 2.5 V.
11: MICBIAS output is powered to AVDD.
Page 1 / Register 47 (0x2F) Through Page 1 / Register 49 (0x31): Reserved
READ/
WRITE
RESET
BIT
DESCRIPTION
VALUE
D7–D0
R
XXXX XXXX Reserved. Do not write to these bits.
Page 1 / Register 50 (0x32): Input CM Settings
READ/
WRITE
RESET
BIT
DESCRIPTION
VALUE
D7
R/W
R/W
R/W
0
0: AIN1 input is floating if it is not used for analog bypass.
1: AIN1 input is connected to CM internally if it is not used for analog bypass.
D6
0
0: AIN2 input is floating if it is not used for analog bypass.
1: AIN2 input is connected to CM internally if it is not used for analog bypass.
D5–D0
00 0000
Reserved. Write only zeros to these bits.
Copyright © 2013, Texas Instruments Incorporated
REGISTER MAP
81
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
Page 1 / Register 51 (0x33) Through Page 1 / Register 127 (0x7F): Reserved
READ/
WRITE
RESET
VALUE
XXXX XXXX Reserved. Write only the reset value to these bits.
BIT
DESCRIPTION
D7–D0
R/W
6.4 Control Registers, Page 3: MCLK Divider for Programmable Delay Timer
Default values shown for this page only become valid 100 μs following a hardware or software reset.
Page 3 / Register 0 (0x00): Page Control Register
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D0
R/W
0000 0000
0000 0000: Page 0 selected
0000 0001: Page 1 selected
...
1111 1110: Page 254 selected
1111 1111: Page 255 selected
The only register used in page 3 is register 16. The remaining page-3 registers are reserved and should
not be written to.
Page 3 / Register 16 (0x10): Timer Clock MCLK Divider
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7
R/W
1
0: Internal oscillator is used for programmable delay timer.
1: External MCLK(1) is used for programmable delay timer.
D6–D0
R/W
000 0001
MCLK Divider to Generate 1-MHz Clock for the Programmable Delay Timer
000 0000: MCLK divider = 128
000 0001: MCLK divider = 1
000 0010: MCLK divider = 2
...
111 1110: MCLK divider = 126
111 1111: MCLK divider = 127
(1) External clock is used only to control the delay programmed between the conversions and not used for doing the actual conversion. This
feature is provided in case a more accurate delay is desired, because the internal oscillator frequency varies from device to device.
6.5 Control Registers, Page 8: DAC Programmable Coefficients RAM Buffer A (1:63)
Default values shown for this page only become valid 100 μs following a hardware or software reset.
Page 8 / Register 0 (0x00): Page Control Register
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D0
R/W
0000 0000
0000 0000: Page 0 selected
0000 0001: Page 1 selected
...
1111 1110: Page 254 selected
1111 1111: Page 255 selected
82
REGISTER MAP
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
Page 8 / Register 1 (0x01): DAC Coefficient RAM Control
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D3
D2
R/W
0000 0
0
Reserved. Write only the reset value.
DAC Adaptive Filtering Control
R/W
0: Adaptive filtering disabled in DAC processing block
1: Adaptive filtering enabled in DAC processing block
D1
D0
R
0
0
DAC Adaptive Filter Buffer Control Flag
0: In adaptive filter mode, DAC processing block accesses DAC coefficient buffer A, and the external
control interface accesses DAC coefficient buffer B.
1: In adaptive filter mode, DAC processing block accesses DAC coefficient buffer B, and the external
control interface accesses DAC coefficient buffer A.
R/W
DAC Adaptive Filter Buffer Switch Control
0: DAC coefficient buffers are not switched at the next frame boundary.
1: DAC coefficient buffers are switched at the next frame boundary, if adaptive filtering mode is enabled.
This bit self-clears on switching.
The remaining page-8 registers are either reserved registers or are used for setting coefficients for the
various filters in the TLV320DAC3100-Q1 Reserved registers should not be written to.
The filter coefficient registers are arranged in pairs, with two adjacent 8-bit registers containing the 16-bit
coefficient for a single filter. The 16-bit integer contained in the MSB and LSB registers for a coefficient is
interpreted as a 2s-complement integer, with possible values ranging from –32,768 to 32,767. When
programming any coefficient value for a filter, the MSB register should always be written first, immediately
followed by the LSB register. Even if only the MSB or LSB portion of the coefficient changes, both
registers should be written in this sequence. Table 6-2 is a list of the page-8 registers, excepting the
previously described register 0 and register 1.
Table 6-2. Page 8 DAC Buffer A Registers
REGISTER
NUMBER
RESET VALUE
REGISTER NAME
2 (0x02)
0111 1111
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0111 1111
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0111 1111
1111 1111
0000 0000
Coefficient N0(15:8) for left DAC-programmable biquad A
Coefficient N0(7:0) for left DAC-programmable biquad A
Coefficient N1(15:8) for left DAC-programmable biquad A
Coefficient N1(7:0) for left DAC-programmable biquad A
Coefficient N2(15:8) for left DAC-programmable biquad A
Coefficient N2(7:0) for left DAC-programmable biquad A
Coefficient D1(15:8) for left DAC-programmable biquad A
Coefficient D1(7:0) for left DAC-programmable biquad A
Coefficient D2(15:8) for left DAC-programmable biquad A
Coefficient D2(7:0) for left DAC-programmable biquad A
Coefficient N0(15:8) for left DAC-programmable biquad B
Coefficient N0(7:0) for left DAC-programmable biquad B
Coefficient N1(15:8) for left DAC-programmable biquad B
Coefficient N1(7:0) for left DAC-programmable biquad B
Coefficient N2(15:8) for left DAC-programmable biquad B
Coefficient N2(7:0) for left DAC-programmable biquad B
Coefficient D1(15:8) for left DAC-programmable biquad B
Coefficient D1(7:0) for left DAC-programmable biquad B
Coefficient D2(15:8) for left DAC-programmable biquad B
Coefficient D2(7:0) for left DAC-programmable biquad B
Coefficient N0(15:8) for left DAC-programmable biquad C
Coefficient N0(7:0) for left DAC-programmable biquad C
Coefficient N1(15:8) for left DAC-programmable biquad C
3 (0x03)
4 (0x04)
5 (0x05)
6 (0x06)
7 (0x07)
8 (0x08)
9 (0x09)
10 (0x0A)
11 (0x0B)
12 (0x0C)
13 (0x0D)
14 (0x0E)
15 (0x0F)
16 (0x10)
17 (0x11)
18 (0x12)
19 (0x13)
20 (0x14)
21 (0x15)
22 (0x16)
23 (0x17)
24 (0x18)
Copyright © 2013, Texas Instruments Incorporated
REGISTER MAP
83
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
Table 6-2. Page 8 DAC Buffer A Registers (continued)
REGISTER
NUMBER
RESET VALUE
REGISTER NAME
25 (0x19)
26 (0x1A)
27 (0x1B)
28 (0x1C)
29 (0x1D)
30 (0x1E)
31 (0x1F)
32 (0x20)
33 (0x21)
34 (0x22)
35 (0x23)
36 (0x24)
37 (0x25)
38 (0x26)
39 (0x27)
40 (0x28)
41 (0x29)
42 (0x2A)
43 (0x2B)
44 (0x2C)
45 (0x2D)
46 (0x2E)
47 (0x2F)
48 (0x30)
49 (0x31)
50 (0x32)
51 (0x33)
52 (0x34)
53 (0x35)
54 (0x36)
55 (0x37)
56 (0x38)
57 (0x39)
58 (0x3A)
59 (0x3B)
60 (0x3C)
61 (0x3D)
62 (0x3E)
63 (0x3F)
64 (0x40)
65 (0x41)
66 (0x42)
67 (0x43)
68 (0x44)
69 (0x45)
70 (0x46)
71 (0x47)
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0111 1111
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0111 1111
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0111 1111
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0111 1111
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
Coefficient N1(7:0) for left DAC-programmable biquad C
Coefficient N2(15:8) for left DAC-programmable biquad C
Coefficient N2(7:0) for left DAC-programmable biquad C
Coefficient D1(15:8) for left DAC-programmable biquad C
Coefficient D1(7:0) for left DAC-programmable biquad C
Coefficient D2(15:8) for left DAC-programmable biquad C
Coefficient D2(7:0) for left DAC-programmable biquad C
Coefficient N0(15:8) for left DAC-programmable biquad D
Coefficient N0(7:0) for left DAC-programmable biquad D
Coefficient N1(15:8) for left DAC-programmable biquad D
Coefficient N1(7:0) for left DAC-programmable biquad D
Coefficient N2(15:8) for left DAC-programmable biquad D
Coefficient N2(7:0) for left DAC-programmable biquad D
Coefficient D1(15:8) for left DAC-programmable biquad D
Coefficient D1(7:0) for left DAC-programmable biquad D
Coefficient D2(15:8) for left DAC-programmable biquad D
Coefficient D2(7:0) for left DAC-programmable biquad D
Coefficient N0(15:8) for left DAC-programmable biquad E
Coefficient N0(7:0) for left DAC-programmable biquad E
Coefficient N1(15:8) for left DAC-programmable biquad E
Coefficient N1(7:0) for left DAC-programmable biquad E
Coefficient N2(15:8) for left DAC-programmable biquad E
Coefficient N2(7:0) for left DAC-programmable biquad E
Coefficient D1(15:8) for left DAC-programmable biquad E
Coefficient D1(7:0) for left DAC-programmable biquad E
Coefficient D2(15:8) for left DAC-programmable biquad E
Coefficient D2(7:0) for left DAC-programmable biquad E
Coefficient N0(15:8) for left DAC-programmable biquad F
Coefficient N0(7:0) for left DAC-programmable biquad F
Coefficient N1(15:8) for left DAC-programmable biquad F
Coefficient N1(7:0) for left DAC-programmable biquad F
Coefficient N2(15:8) for left DAC-programmable biquad F
Coefficient N2(7:0) for left DAC-programmable biquad F
Coefficient D1(15:8) for left DAC-programmable biquad F
Coefficient D1(7:0) for left DAC-programmable biquad F
Coefficient D2(15:8) for left DAC-programmable biquad F
Coefficient D2(7:0) for left DAC-programmable biquad F
Reserved
Reserved
8 MSBs of 3D PGA gain for PRB_P23, PRB_P24 and PRB_P25
8 LSBs of 3D PGA gain for PRB_P23, PRB_P24 and PRB_P25
Coefficient N0(15:8) for right DAC-programmable biquad A
Coefficient N0(7:0) for right DAC-programmable biquad A
Coefficient N1(15:8) for right DAC-programmable biquad A
Coefficient N1(7:0) for right DAC-programmable biquad A
Coefficient N2(15:8) for right DAC-programmable biquad A
Coefficient N2(7:0) for right DAC-programmable biquad A
84
REGISTER MAP
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
Table 6-2. Page 8 DAC Buffer A Registers (continued)
REGISTER
RESET VALUE
REGISTER NAME
NUMBER
72 (0x48)
73 (0x49)
74 (0x4A)
75 (0x4B)
76 (0x4C)
77 (0x4D)
78 (0x4E)
79 (0x4F)
80 (0x50)
81 (0x51)
82 (0x52)
83 (0x53)
84 (0x54)
85 (0x55)
86 (0x56)
87 (0x57)
88 (0x58)
89 (0x59)
90 (0x5A)
91 (0x5B)
92 (0x5C)
93 (0x5D)
94 (0x5E)
95 (0x5F)
96 (0x60)
97 (0x61)
98 (0x62)
99 (0x63)
100 (0x64)
101 (0x65)
102 (0x66)
103 (0x67)
104 (0x68)
105 (0x69)
106 (0x6A)
107 (0x6B)
108 (0x6C)
109 (0x6D)
110 (0x6E)
111 (0x6F)
112 (0x70)
113 (0x71)
114 (0x72)
115 (0x73)
116 (0x74)
117 (0x75)
118 (0x76)
0000 0000
0000 0000
0000 0000
0000 0000
0111 1111
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0111 1111
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0111 1111
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0111 1111
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0111 1111
1111 1111
0000 0000
Coefficient D1(15:8) for right DAC-programmable biquad A
Coefficient D1(7:0) for right DAC-programmable biquad A
Coefficient D2(15:8) for right DAC-programmable biquad A
Coefficient D2(7:0) for right DAC-programmable biquad A
Coefficient N0(15:8) for right DAC-programmable biquad B
Coefficient N0(7:0) for right DAC-programmable biquad B
Coefficient N1(15:8) for right DAC-programmable biquad B
Coefficient N1(7:0) for right DAC-programmable biquad B
Coefficient N2(15:8) for right DAC-programmable biquad B
Coefficient N2(7:0) for right DAC-programmable biquad B
Coefficient D1(15:8) for right DAC-programmable biquad B
Coefficient D1(7:0) for right DAC-programmable biquad B
Coefficient D2(15:8) for right DAC-programmable biquad B
Coefficient D2(7:0) for right DAC-programmable biquad B
Coefficient N0(15:8) for right DAC-programmable biquad C
Coefficient N0(7:0) for right DAC-programmable biquad C
Coefficient N1(15:8) for right DAC-programmable biquad C
Coefficient N1(7:0) for right DAC-programmable biquad C
Coefficient N2(15:8) for right DAC-programmable biquad C
Coefficient N2(7:0) for right DAC-programmable biquad C
Coefficient D1(15:8) for right DAC-programmable biquad C
Coefficient D1(7:0) for right DAC-programmable biquad C
Coefficient D2(15:8) for right DAC-programmable biquad C
Coefficient D2(7:0) for right DAC-programmable biquad C
Coefficient N0(15:8) for right DAC-programmable biquad D
Coefficient N0(7:0) for right DAC-programmable biquad D
Coefficient N1(15:8) for right DAC-programmable biquad D
Coefficient N1(7:0) for right DAC-programmable biquad D
Coefficient N2(15:8) for right DAC-programmable biquad D
Coefficient N2(7:0) for right DAC-programmable biquad D
Coefficient D1(15:8) for right DAC-programmable biquad D
Coefficient D1(7:0) for right DAC-programmable biquad D
Coefficient D2(15:8) for right DAC-programmable biquad D
Coefficient D2(7:0) for right DAC-programmable biquad D
Coefficient N0(15:8) for right DAC-programmable biquad E
Coefficient N0(7:0) for right DAC-programmable biquad E
Coefficient N1(15:8) for right DAC-programmable biquad E
Coefficient N1(7:0) for right DAC-programmable biquad E
Coefficient N2(15:8) for right DAC-programmable biquad E
Coefficient N2(7:0) for right DAC-programmable biquad E
Coefficient D1(15:8) for right DAC-programmable biquad E
Coefficient D1(7:0) for right DAC-programmable biquad E
Coefficient D2(15:8) for right DAC-programmable biquad E
Coefficient D2(7:0) for right DAC-programmable biquad E
Coefficient N0(15:8) for right DAC-programmable biquad F
Coefficient N0(7:0) for right DAC-programmable biquad F
Coefficient N1(15:8) for right DAC-programmable biquad F
Copyright © 2013, Texas Instruments Incorporated
REGISTER MAP
85
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
Table 6-2. Page 8 DAC Buffer A Registers (continued)
REGISTER
NUMBER
RESET VALUE
REGISTER NAME
119 (0x77)
120 (0x78)
121 (0x79)
122 (0x7A)
123 (0x7B)
124 (0x7C)
125 (0x7D)
126–127
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
Coefficient N1(7:0) for right DAC-programmable biquad F
Coefficient N2(15:8) for right DAC-programmable biquad F
Coefficient N2(7:0) for right DAC-programmable biquad F
Coefficient D1(15:8) for right DAC-programmable biquad F
Coefficient D1(7:0) for right DAC-programmable biquad F
Coefficient D2(15:8) for right DAC-programmable biquad F
Coefficient D2(7:0) for right DAC-programmable biquad F
Reserved
86
REGISTER MAP
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
6.6 Control Registers, Page 9: DAC Programmable Coefficients RAM Buffer A (65:127)
Default values shown for this page only become valid 100 μs following a hardware or software reset.
Page 9 / Register 0 (0x00): Page Control Register
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D0
R/W
0000 0000
0000 0000: Page 0 selected
0000 0001: Page 1 selected
...
1111 1110: Page 254 selected
1111 1111: Page 255 selected
The remaining page-9 registers are either reserved registers or are used for setting coefficients for the
various filters in the TLV320DAC3100-Q1. Reserved registers should not be written to.
The filter-coefficient registers are arranged in pairs, with two adjacent 8-bit registers containing the 16-bit
coefficient for a single filter. The 16-bit integer contained in the MSB and LSB registers for a coefficient is
interpreted as a 2s-complement integer, with possible values ranging from –32,768 to 32,767. When
programming any coefficient value for a filter, the MSB register should always be written first, immediately
followed by the LSB register. Even if only the MSB or LSB portion of the coefficient changes, both
registers should be written in this sequence. Table 6-3 is a list of the page-9 registers, excepting the
previously described register 0.
Table 6-3. Page 9 DAC Buffer A Registers
REGISTER
NUMBER
RESET VALUE
REGISTER NAME
Reserved. Do not write to this register.
1 (0x01)
XXXX XXXX
0111 1111
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
0111 1111
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
0111 1111
1111 0111
1000 0000
0000 1001
0111 1111
1110 1111
0000 0000
0001 0001
0000 0000
0001 0001
0111 1111
1101 1110
0000 0000
2 (0x02)
Coefficient N0(15:8) for left DAC-programmable first-order IIR
Coefficient N0(7:0) for left DAC-programmable first-order IIR
Coefficient N1(15:8) for left DAC-programmable first-order IIR
Coefficient N1(7:0) for left DAC-programmable first-order IIR
Coefficient D1(15:8) for left DAC-programmable first-order IIR
Coefficient D1(7:0) for left DAC-programmable first-order IIR
Coefficient N0(15:8) for right DAC-programmable first-order IIR
Coefficient N0(7:0) for right DAC-programmable first-order IIR
Coefficient N1(15:8) for right DAC-programmable first-order IIR
Coefficient N1(7:0) for right DAC-programmable first-order IIR
Coefficient D1(15:8) for right DAC-programmable first-order IIR
Coefficient D1(7:0) for right DAC-programmable first-order IIR
Coefficient N0(15:8) for DRC first-order high-pass filter
Coefficient N0(7:0) for DRC first-order high-pass filter
Coefficient N1(15:8) for DRC first-order high-pass filter
Coefficient N1(7:0) for DRC first-order high-pass filter
Coefficient D1(15:8) for DRC first-order high-pass filter
Coefficient D1(7:0) for DRC first-order high-pass filter
Coefficient N0(15:8) for DRC first-order low-pass filter
Coefficient N0(7:0) for DRC first-order low-pass filter
Coefficient N1(15:8) for DRC first-order low-pass filter
Coefficient N1(7:0) for DRC first-order low-pass filter
Coefficient D1(15:8) for DRC first-order low-pass filter
Coefficient D1(7:0) for DRC first-order low-pass filter
Reserved
3 (0x03)
4 (0x04)
5 (0x05)
6 (0x06)
7 (0x07)
8 (0x08)
9 (0x09)
10 (0x0A)
11 (0x0B)
12 (0x0C)
13 (0x0D)
14 (0x0E)
15 (0x0F)
16 (0x10)
17 (0x11)
18 (0x12)
19 (0x13)
20 (0x14)
21 (0x15)
22 (0x16)
23 (0x17)
24 (0x18)
25 (0x19)
26–127
Copyright © 2013, Texas Instruments Incorporated
REGISTER MAP
87
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
6.7 Control Registers, Page 12: DAC Programmable Coefficients RAM Buffer B (1:63)
Table 6-4. Page 12 / Register 0 (0x00): Page Control Register
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D0
R/W
0000 0000
0000 0000: Page 0 selected
0000 0001: Page 1 selected
...
1111 1110: Page 254 selected
1111 1111: Page 255 selected
The remaining page-12 registers are either reserved registers or are used for setting coefficients for the
various filters in the TLV320DAC3100-Q1. Reserved registers should not be written to.
The filter-coefficient registers are arranged in pairs, with two adjacent 8-bit registers containing the 16-bit
coefficient for a single filter. The 16-bit integer contained in the MSB and LSB registers for a coefficient is
interpreted as a 2s-complement integer, with possible values ranging from –32,768 to 32,767. When
programming any coefficient value for a filter, the MSB register should always be written first, immediately
followed by the LSB register. Even if only the MSB or LSB portion of the coefficient changes, both
registers should be written in this sequence. Table 6-5 is a list of the page-12 registers, excepting the
previously described register 0.
Table 6-5. Page-12 DAC Buffer B Registers
REGISTER
NUMBER
RESET VALUE
REGISTER NAME
Reserved. Do not write to this register.
1 (0x01)
0000 0000
0111 1111
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0111 1111
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0111 1111
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
2 (0x02)
Coefficient N0(15:8) for left DAC-programmable biquad A
Coefficient N0(7:0) for left DAC-programmable biquad A
Coefficient N1(15:8) for left DAC-programmable biquad A
Coefficient N1(7:0) for left DAC-programmable biquad A
Coefficient N2(15:8) for left DAC-programmable biquad A
Coefficient N2(7:0) for left DAC-programmable biquad A
Coefficient D1(15:8) for left DAC-programmable biquad A
Coefficient D1(7:0) for left DAC-programmable biquad A
Coefficient D2(15:8) for left DAC-programmable biquad A
Coefficient D2(7:0) for left DAC-programmable biquad A
Coefficient N0(15:8) for left DAC-programmable biquad B
Coefficient N0(7:0) for left DAC-programmable biquad B
Coefficient N1(15:8) for left DAC-programmable biquad B
Coefficient N1(7:0) for left DAC-programmable biquad B
Coefficient N2(15:8) for left DAC-programmable biquad B
Coefficient N2(7:0) for left DAC-programmable biquad B
Coefficient D1(15:8) for left DAC-programmable biquad B
Coefficient D1(7:0) for left DAC-programmable biquad B
Coefficient D2(15:8) for left DAC-programmable biquad B
Coefficient D2(7:0) for left DAC-programmable biquad B
Coefficient N0(15:8) for left DAC-programmable biquad C
Coefficient N0(7:0) for left DAC-programmable biquad C
Coefficient N1(15:8) for left DAC-programmable biquad C
Coefficient N1(7:0) for left DAC-programmable biquad C
Coefficient N2(15:8) for left DAC-programmable biquad C
Coefficient N2(7:0) for left DAC-programmable biquad C
3 (0x03)
4 (0x04)
5 (0x05)
6 (0x06)
7 (0x07)
8 (0x08)
9 (0x09)
10 (0x0A)
11 (0x0B)
12 (0x0C)
13 (0x0D)
14 (0x0E)
15 (0x0F)
16 (0x10)
17 (0x11)
18 (0x12)
19 (0x13)
20 (0x14)
21 (0x15)
22 (0x16)
23 (0x17)
24 (0x18)
25 (0x19)
26 (0x1A)
27 (0x1B)
88
REGISTER MAP
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
Table 6-5. Page-12 DAC Buffer B Registers (continued)
REGISTER
RESET VALUE
REGISTER NAME
NUMBER
28 (0x1C)
29 (0x1D)
30 (0x1E)
31 (0x1F)
32 (0x20)
33 (0x21)
34 (0x22)
35 (0x23)
36 (0x24)
37 (0x25)
38 (0x26)
39 (0x27)
40 (0x28)
41 (0x29)
42 (0x2A)
43 (0x2B)
44 (0x2C)
45 (0x2D)
46 (0x2E)
47 (0x2F)
48 (0x30)
49 (0x31)
50 (0x32)
51 (0x33)
52 (0x34)
53 (0x35)
54 (0x36)
55 (0x37)
56 (0x38)
57 (0x39)
58 (0x3A)
59 (0x3B)
60 (0x3C)
61 (0x3D)
62 (0x3E)
63 (0x3F)
64 (0x40)
65 (0x41)
66 (0x42)
67 (0x43)
68 (0x44)
69 (0x45)
70 (0x46)
71 (0x47)
72 (0x48)
73 (0x49)
74 (0x4A)
0000 0000
0000 0000
0000 0000
0000 0000
0111 1111
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0111 1111
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0111 1111
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0111 1111
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
Coefficient D1(15:8) for left DAC-programmable biquad C
Coefficient D1(7:0) for left DAC-programmable biquad C
Coefficient D2(15:8) for left DAC-programmable biquad C
Coefficient D2(7:0) for left DAC-programmable biquad C
Coefficient N0(15:8) for left DAC-programmable biquad D
Coefficient N0(7:0) for left DAC-programmable biquad D
Coefficient N1(15:8) for left DAC-programmable biquad D
Coefficient N1(7:0) for left DAC-programmable biquad D
Coefficient N2(15:8) for left DAC-programmable biquad D
Coefficient N2(7:0) for left DAC-programmable biquad D
Coefficient D1(15:8) for left DAC-programmable biquad D
Coefficient D1(7:0) for left DAC-programmable biquad D
Coefficient D2(15:8) for left DAC-programmable biquad D
Coefficient D2(17:0) for left DAC-programmable biquad D
Coefficient N0(15:8) for left DAC-programmable biquad E
Coefficient N0(7:0) for left DAC-programmable biquad E
Coefficient N1(15:8) for left DAC-programmable biquad E
Coefficient N1(7:0) for left DAC-programmable biquad E
Coefficient N2(15:8) for left DAC-programmable biquad E
Coefficient N2(7:0) for left DAC-programmable biquad E
Coefficient D1(15:8) for left DAC-programmable biquad E
Coefficient D1(7:0) for left DAC-programmable biquad E
Coefficient D2(15:8) for left DAC-programmable biquad E
Coefficient D2(7:0) for left DAC-programmable biquad E
Coefficient N0(15:8) for left DAC-programmable biquad F
Coefficient N0(7:0) for left DAC-programmable biquad F
Coefficient N1(15:8) for left DAC-programmable biquad F
Coefficient N1(7:0) for left DAC-programmable biquad F
Coefficient N2(15:8) for left DAC-programmable biquad F
Coefficient N2(7:0) for left DAC-programmable biquad F
Coefficient D1(15:8) for left DAC-programmable biquad F
Coefficient D1(7:0) for left DAC-programmable biquad F
Coefficient D2(15:8) for left DAC-programmable biquad F
Coefficient D2(7:0) for left DAC-programmable biquad F
Reserved
Reserved
8 MSBs 3D PGA gain for PRB_P23, PRB_P24 and PRB_P25
8 LSBs 3D PGA gain for PRB_P23, PRB_P24 and PRB_P25
Coefficient N0(15:8) for right DAC-programmable biquad A
Coefficient N0(7:0) for right DAC-programmable biquad A
Coefficient N1(15:8) for right DAC-programmable biquad A
Coefficient N1(7:0) for right DAC-programmable biquad A
Coefficient N2(15:8) for right DAC-programmable biquad A
Coefficient N2(7:0) for right DAC-programmable biquad A
Coefficient D1(15:8) for right DAC-programmable biquad A
Coefficient D1(7:0) for right DAC-programmable biquad A
Coefficient D2(15:8) for right DAC-programmable biquad A
Copyright © 2013, Texas Instruments Incorporated
REGISTER MAP
89
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
Table 6-5. Page-12 DAC Buffer B Registers (continued)
REGISTER
NUMBER
RESET VALUE
REGISTER NAME
75 (0x4B)
76 (0x4C)
77 (0x4D)
78 (0x4E)
79 (0x4F)
80 (0x50)
81 (0x51)
82 (0x52)
83 (0x53)
84 (0x54)
85 (0x55)
86 (0x56)
87 (0x57)
88 (0x58)
89 (0x59)
90 (0x5A)
91 (0x5B)
92 (0x5C)
93 (0x5D)
94 (0x5E)
95 (0x5F)
96 (0x60)
97 (0x61)
98 (0x62)
99 (0x63)
100 (0x64)
101 (0x65)
102 (0x66)
103 (0x67)
104 (0x68)
105 (0x69)
106 (0x6A)
107 (0x6B)
108 (0x6C)
109 (0x6D)
110 (0x6E)
111 (0x6F)
112 (0x70)
113 (0x71)
114 (0x72)
115 (0x73)
116 (0x74)
117 (0x75)
118 (0x76)
119 (0x77)
120 (0x78)
121 (0x79)
0000 0000
0111 1111
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0111 1111
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0111 1111
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0111 1111
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
0111 1111
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
Coefficient D2(7:0) for right DAC-programmable biquad A
Coefficient N0(15:8) for right DAC-programmable biquad B
Coefficient N0(7:0) for right DAC-programmable biquad B
Coefficient N1(15:8) for right DAC-programmable biquad B
Coefficient N1(7:0) for right DAC-programmable biquad B
Coefficient N2(15:8) for right DAC-programmable biquad B
Coefficient N2(7:0) for right DAC-programmable biquad B
Coefficient D1(15:8) for right DAC-programmable biquad B
Coefficient D1(7:0) for right DAC-programmable biquad B
Coefficient D2(15:8) for right DAC-programmable biquad B
Coefficient D2(7:0) for right DAC-programmable biquad B
Coefficient N0(15:8) for right DAC-programmable biquad C
Coefficient N0(7:0) for right DAC-programmable biquad C
Coefficient N1(15:8) for right DAC-programmable biquad C
Coefficient N1(7:0) for right DAC-programmable biquad C
Coefficient N2(15:8) for right DAC-programmable biquad C
Coefficient N2(7:0) for right DAC-programmable biquad C
Coefficient D1(15:8) for right DAC-programmable biquad C
Coefficient D1(7:0) for right DAC-programmable biquad C
Coefficient D2(15:8) for right DAC-programmable biquad C
Coefficient D2(7:0) for right DAC-programmable biquad C
Coefficient N0(15:8) for right DAC-programmable biquad D
Coefficient N0(7:0) for right DAC-programmable biquad D
Coefficient N1(15:8) for right DAC-programmable biquad D
Coefficient N1(7:0) for right DAC-programmable biquad D
Coefficient N2(15:8) for right DAC-programmable biquad D
Coefficient N2(7:0) for right DAC-programmable biquad D
Coefficient D1(15:8) for right DAC-programmable biquad D
Coefficient D1(7:0) for right DAC-programmable biquad D
Coefficient D2(15:8) for right DAC-programmable biquad D
Coefficient D2(7:0) for right DAC-programmable biquad D
Coefficient N0(15:8) for right DAC-programmable biquad E
Coefficient N0(7:0) for right DAC-programmable biquad E
Coefficient N1(15:8) for right DAC-programmable biquad E
Coefficient N1(7:0) for right DAC-programmable biquad E
Coefficient N2(15:8) for right DAC-programmable biquad E
Coefficient N2(7:0) for right DAC-programmable biquad E
Coefficient D1(15:8) for right DAC-programmable biquad E
Coefficient D1(7:0) for right DAC-programmable biquad E
Coefficient ND2(15:8) for right DAC-programmable biquad E
Coefficient ND2(7:0) for right DAC-programmable biquad E
Coefficient N0(15:8) for right DAC-programmable biquad F
Coefficient N0(7:0) for right DAC-programmable biquad F
Coefficient N1(15:8) for right DAC-programmable biquad F
Coefficient N1(7:0) for right DAC-programmable biquad F
Coefficient N2(15:8) for right DAC-programmable biquad F
Coefficient N2(7:0) for right DAC-programmable biquad F
90
REGISTER MAP
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
Table 6-5. Page-12 DAC Buffer B Registers (continued)
REGISTER
RESET VALUE
REGISTER NAME
NUMBER
122 (0x7A)
123 (0x7B)
124 (0x7C)
125 (0x7D)
126–127
0000 0000
0000 0000
0000 0000
0000 0000
0000 0000
Coefficient D1(15:8) for right DAC-programmable biquad F
Coefficient D1(7:0) for right DAC-programmable biquad F
Coefficient D2(15:8) for right DAC-programmable biquad F
Coefficient D2(7:0) for right DAC-programmable biquad F
Reserved
6.8 Control Registers, Page 13: DAC Programmable Coefficients RAM Buffer B (65:127)
Table 6-6. Page 13 / Register 0 (0x00): Page Control Register
READ/
WRITE
RESET
VALUE
BIT
DESCRIPTION
D7–D0
R/W
0000 0000
0000 0000: Page 0 selected
0000 0001: Page 1 selected
...
1111 1110: Page 254 selected
1111 1111: Page 255 selected
The remaining page-13 registers are either reserved registers or are used for setting coefficients for the
various filters in the TLV320DAC3100-Q1. Reserved registers should not be written to.
The filter-coefficient registers are arranged in pairs, with two adjacent 8-bit registers containing the 16-bit
coefficient for a single filter. The 16-bit integer contained in the MSB and LSB registers for a coefficient is
interpreted as a 2s-complement integer, with possible values ranging from –32,768 to 32,767. When
programming any coefficient value for a filter, the MSB register should always be written first, immediately
followed by the LSB register. Even if only the MSB or LSB portion of the coefficient changes, both
registers should be written in this sequence. Table 6-7 is a list of the page-13 registers, excepting the
previously described register 0.
Table 6-7. Page 13 DAC Buffer B Registers
REGISTER
NUMBER
RESET VALUE
REGISTER NAME
Reserved. Do not write to this register.
1
0000 0000
0111 1111
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
0111 1111
1111 1111
0000 0000
0000 0000
0000 0000
0000 0000
0111 1111
1111 0111
1000 0000
0000 1001
0111 1111
1110 1111
2 (0x02)
3 (0x03)
4 (0x04)
5 (0x05)
6 (0x06)
7 (0x07)
8 (0x08)
9 (0x09)
10 (0x0A)
11 (0x0B)
12 (0x0C)
13 (0x0D)
14 (0x0E)
15 (0x0F)
16 (0x10)
17 (0x11)
18 (0x12)
19 (0x13)
Coefficient N0(15:8) for left DAC-programmable first-order IIR
Coefficient N0(7:0) for left DAC-programmable first-order IIR
Coefficient N1(15:8) for left DAC-programmable first-order IIR
Coefficient N1(7:0) for left DAC-programmable first-order IIR
Coefficient D1(15:8) for left DAC-programmable first-order IIR
Coefficient D1(7:0) for left DAC-programmable first-order IIR
Coefficient N0(15:8) for right DAC-programmable first-order IIR
Coefficient N0(7:0) for right DAC-programmable first-order IIR
Coefficient N1(15:8) for right DAC-programmable first-order IIR
Coefficient N1(7:0) for right DAC-programmable first-order IIR
Coefficient D1(15:8) for right DAC-programmable first-order IIR
Coefficient D1(7:0) for right DAC-programmable first-order IIR
Coefficient N0(15:8) for DRC first-order high-pass filter
Coefficient N0(7:0) for DRC first-order high-pass filter
Coefficient N1(15:8) for DRC first-order high-pass filter
Coefficient N1(7:0) for DRC first-order high-pass filter
Coefficient D1(15:8) for DRC first-order high-pass filter
Coefficient D1(7:0) for DRC first-order high-pass filter
Copyright © 2013, Texas Instruments Incorporated
REGISTER MAP
91
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
SLAS896A –JULY 2013–REVISED AUGUST 2013
www.ti.com
Table 6-7. Page 13 DAC Buffer B Registers (continued)
REGISTER
NUMBER
RESET VALUE
REGISTER NAME
20 (0x14)
21 (0x15)
22 (0x16)
23 (0x17)
24 (0x18)
25 (0x19)
26–127
0000 0000
0001 0001
0000 0000
0001 0001
0111 1111
1101 1110
0000 0000
Coefficient N0(15:8) for DRC first-order low-pass filter
Coefficient N0(7:0) for DRC first-order low-pass filter
Coefficient N1(15:8) for DRC first-order low-pass filter
Coefficient N1(7:0) for DRC first-order low-pass filter
Coefficient D1(15:8) for DRC first-order low-pass filter
Coefficient D1(7:0) for DRC first-order low-pass filter
Reserved
92
REGISTER MAP
Copyright © 2013, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
TLV320DAC3100-Q1
www.ti.com
SLAS896A –JULY 2013–REVISED AUGUST 2013
Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Original (July 2013) to Revision A
Page
Changed AEC temperature grade from 2 to 3 to include max ambient temp change from 105 to 85 .................... 1
•
•
•
•
•
•
•
•
Changed maximum Ambient temperature range from 105 to 85 in Absolute Maximum Ratings table ................... 5
Changed maximum operating free-air temperature value from 105 to 85. ................................................... 6
Changed condition statement in Electrical Characteristics table by removing TA temperature range .................... 6
Changed condition statement in Electrical Characteristics table by removing TA temperature range .................... 7
Added Power-Supply Sequence section to Device Initialization section .................................................... 17
Changed register 36 to register 35 in section Section 5.4.2 .................................................................. 22
Changed Section 5.5.1.2 diagrams for PRB_P2/5/8/10/13/15/18/21/24/25 to relect that the DRC_HPF filter
cannot be bypassed when the DRC is turned off .............................................................................. 24
Changed HPF and LPF cutoff values from 0.0016 to 0.000083 and 0.00033 to 0.000165 in the Dynamic Range
Compression section ............................................................................................................... 34
Deleted dec2hex from MATLAB script in Key-Click Functionality With Digital Sine-Wave Generator (PRB_P25)
section ............................................................................................................................... 38
Changed note 1. of MATLAB script in Key-Click Functionality With Digital Sine-Wave Generator (PRB_P25)
section from Fin less than Fs / 4 to less than 0.5*Fs and not equal to 0 or 0.25*Fs ...................................... 38
Added sequence for inserting a beep in the middle of an already-playing signal and note text following script in
the Key-Click Functionality With Digital Sine-Wave Generator (PRB_P25) section ....................................... 39
Deleted Analog Volume Control for Headphone and Speaker Outputs (for D7=0) table and added table note to
D7=1 table. .......................................................................................................................... 42
Added D6–D0 to the Register Value column heading and changed Analog Attenuation to Analog Gain. ............. 42
Changed page 0 to page 1 in section Section 5.5.12.1 ....................................................................... 43
Changed PRB_Rx to PRB_Px in DAC Setup section ......................................................................... 45
Added 80 MHz ≤ (PLL_CLKIN × J.D × R/P)≤ 110 MHz and 4 ≤ R × J ≤ 259 under equation 7. ........................ 52
Added 80 MHz ≤ PLL_CLKIN × J.D × R/P ≤ 110 MHz and R = 1 under equation 8. ..................................... 52
Added Timer section and image after PLL section. ............................................................................ 53
Changed part number from TLV320DAC3101 to TLV320DAC3100. ........................................................ 62
Deleted reference to Dig_Mic_In in Page 0 / Register 54 table for bits D2-D1 ............................................ 70
Added table note to Page 0 / Register 64 (0x40): DAC VOLUME CONTROL. ............................................ 71
Changed values in Page 0 / Register 69 (0x45): DRC Control 2 ............................................................ 73
Changed Page 0, Register 70, bit D3-D0 decay rate value for 0000 from DR = 1.5625e–3 to DR = 0.015625 ........ 74
Changed D0=1 to Reserved in Page 1 / Register 33. ......................................................................... 78
Removed extraneous cross-references for deleted table. .................................................................... 79
Added table note to Page 1 / Register 40 (0x28): HPL Driver. ............................................................... 80
Added table note to Page 1 / Register 41 (0x29): HPR Driver. .............................................................. 80
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Copyright © 2013, Texas Instruments Incorporated
REGISTER MAP
93
Submit Documentation Feedback
Product Folder Links: TLV320DAC3100-Q1
PACKAGE OPTION ADDENDUM
www.ti.com
23-Nov-2013
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(6)
(3)
(4/5)
6PA3100IRHBRQ1
ACTIVE
VQFN
RHB
32
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-3-260C-168 HR
-40 to 85
6PAIC
3100IQ
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
23-Nov-2013
OTHER QUALIFIED VERSIONS OF TLV320DAC3100-Q1 :
Catalog: TLV320DAC3100
•
NOTE: Qualified Version Definitions:
Catalog - TI's standard catalog product
•
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Nov-2013
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
6PA3100IRHBRQ1
VQFN
RHB
32
3000
330.0
12.4
5.3
5.3
1.5
8.0
12.0
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Nov-2013
*All dimensions are nominal
Device
Package Type Package Drawing Pins
VQFN RHB 32
SPQ
Length (mm) Width (mm) Height (mm)
367.0 367.0 35.0
6PA3100IRHBRQ1
3000
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号:
TLV320DAC3100IRHBR
Low-Power Stereo Audio DAC With Audio Processing and Mono Class-D Speaker Amplifier
TI
TLV320DAC3100IRHBT
Low-Power Stereo Audio DAC With Audio Processing and Mono Class-D Speaker Amplifier
TI
TLV320DAC3100_14
Low-Power Stereo Audio DAC With Audio Processing and Mono Class-D Speaker Amplifier
TI
TLV320DAC3101
Low-Power Stereo Audio DAC With Audio Processing and Stereo Class-D Speaker Amplifier
TI
TLV320DAC3101IRHBR
Low-Power Stereo Audio DAC With Audio Processing and Stereo Class-D Speaker Amplifier
TI
TLV320DAC3101IRHBT
Low-Power Stereo Audio DAC With Audio Processing and Stereo Class-D Speaker Amplifier
TI
TLV320DAC3101_14
Low-Power Stereo Audio DAC With Audio Processing and Stereo Class-D Speaker Amplifier
TI
TLV320DAC3120IRHBR
Low-Power Mono Audio DAC With Embedded miniDSP and Mono Class-D Speaker Amplifier
TI
TLV320DAC3120IRHBT
Low-Power Mono Audio DAC With Embedded miniDSP and Mono Class-D Speaker Amplifier
TI
TLV320DAC3120_10
Low-Power Mono Audio DAC With Embedded miniDSP and Mono Class-D Speaker Amplifier
TI
TLV320DAC3120_14
Low-Power Mono Audio DAC With Embedded miniDSP and Mono Class-D Speaker Amplifier
TI
©2020 ICPDF网 联系我们和版权申明