TLV840-Q1_V03 [TI]
TLV840-Q1 Nano-Power Voltage Supervisor with Adjustable Reset Time Delay;型号: | TLV840-Q1_V03 |
厂家: | TEXAS INSTRUMENTS |
描述: | TLV840-Q1 Nano-Power Voltage Supervisor with Adjustable Reset Time Delay |
文件: | 总32页 (文件大小:2138K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TLV840-Q1
SNVSBY3A – NOVEMBER 2020 – REVISED APRIL 2021
TLV840-Q1 Nano-Power Voltage Supervisor with Adjustable Reset Time Delay
1 Features
3 Description
Qualified for automotive applications:
The TLV840-Q1 device is a voltage supervisor or
reset IC that can operate at wide input voltage levels
from 0.7 V to 6 V while maintaining very low quiescent
current across the whole VDD and temperature range.
TLV840-Q1 offers the best combination of low power
consumption, high accuracy and low propagation
delay (tp_HL= 30 µs typical).
•
AEC-Q100 qualified with the following results:
– Device temperature grade 1: –40°C to +125°C
ambient operating temperature
– Device HBM ESD classification level 2
– Device CDM ESD classification level C7B
Designed for high performance:
Reset output signal is asserted when the voltage at
VDD drops below the negative voltage threshold
(VIT-). Reset signal is cleared when VDD rise above
VIT- plus hysteresis (VHYS) and the reset time delay
(tD) expires. Reset time delay can be programmed
by connecting a capacitor between the CT pin and
ground. For a minimum reset delay time the CT pin
can be left floating. The TLV840-Q1, with its manual
reset pin (MR), offers program flexibility by forcing the
system into a hard reset when the pin is asserted.
•
•
•
•
Nano supply current : 120 nA (Typ)
High accuracy: ±0.5% (Typ)
Built-in hysteresis (VHYS): 5% (Typ)
Fixed threshold voltage (VIT-): 0.8 V to 5.4 V
Designed for a wide range of applications:
•
•
•
Operating voltage range : 0.7 V to 6 V
Fixed (VIT-) voltage: 0.8 V to 5.4 V in 0.1 V steps
Programmable reset time delay (tD)
– Min time delay: 40 µs (typ) without capacitor
Active-low manual reset (MR)
Additional features: Low power-on reset voltage
(VPOR), built-in glitch immunity protection for VDD,
built-in hysteresis, low open-drain output leakage
current (Ilkg(OD)). TLV840-Q1 is a perfect voltage
monitoring solution for automotive applications and
battery-powered / low-power applications.
•
Multiple output topologies / Package type:
•
Four output topologies (RESET / RESET):
– TLV840MADL-Q1: open-drain, active-low
– TLV840MAPL-Q1: push-pull, active-low
– TLV840MADH-Q1: open-drain, active-high
– TLV840MAPH-Q1: push-pull, active-high
Package: SOT23-5 (DBV)
Device Information
PART NUMBER
PACKAGE (1)
BODY SIZE (NOM)
TLV840-Q1
SOT-23 (5) (DBV)
2.90 mm × 1.60 mm
•
2 Applications
(1) For package details, see the mechanical drawing addendum
at the end of the data sheet.
•
•
•
•
•
•
•
Surround view system, front camera
Automotive gateway
Radar ECU
Automotive head unit
ADAS controller
Emergency call
Telematics control unit
0.4
25°C
-40°C
125°C
3.3 V
5 V
IN
LDO
OUT
0.36
0.32
0.28
0.24
0.2
*Rpu
VDD
VDD
Microcontroller
RESET
CT
RESET
TLV840MADL29Q1
MR
GND
0.16
0.12
0.08
*Rpu only for open-drain output
Typical Application Circuit
0.5
1
1.5
2
2.5
3 3.5
VDD (V)
4
4.5
5
5.5
6
IDDv
Typical Supply Current
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TLV840-Q1
SNVSBY3A – NOVEMBER 2020 – REVISED APRIL 2021
www.ti.com
Table of Contents
1 Features............................................................................1
2 Applications.....................................................................1
3 Description.......................................................................1
4 Revision History.............................................................. 2
5 Device Comparison.........................................................3
6 Pin Configuration and Functions...................................4
7 Specifications.................................................................. 5
7.1 Absolute Maximum Ratings ....................................... 5
7.2 ESD Ratings .............................................................. 5
7.3 Recommended Operating Conditions ........................5
7.4 Thermal Information ...................................................5
7.5 Electrical Characteristics ............................................6
7.6 Timing Requirements .................................................7
7.7 Timing Diagrams ........................................................8
7.8 Typical Characteristics .............................................10
8 Detailed Description......................................................12
8.1 Overview...................................................................12
8.2 Functional Block Diagram.........................................12
8.3 Feature Description...................................................12
8.4 Device Functional Modes..........................................17
9 Application and Implementation..................................18
9.1 Application Information............................................. 18
9.2 Typical Application.................................................... 18
10 Power Supply Recommendations..............................21
11 Layout...........................................................................22
11.1 Layout Guidelines................................................... 22
11.2 Layout Example...................................................... 22
12 Device and Documentation Support..........................23
12.1 Device Nomenclature..............................................23
12.2 Receiving Notification of Documentation Updates..24
12.3 Support Resources................................................. 24
12.4 Trademarks.............................................................24
13 Mechanical, Packaging, and Orderable
Information.................................................................... 24
4 Revision History
Changes from Revision * (November 2020) to Revision A (April 2021)
Page
•
RTM release....................................................................................................................................................... 1
Copyright © 2021 Texas Instruments Incorporated
2
Submit Document Feedback
Product Folder Links: TLV840-Q1
TLV840-Q1
SNVSBY3A – NOVEMBER 2020 – REVISED APRIL 2021
www.ti.com
5 Device Comparison
Figure 5-1 shows the device naming nomenclature to compare the different device variants. See Section 12.1 for
a more detailed explanation.
Q1
TLV 840 X X XX XX XXX
Feature Op on
M: Capacitor delay (CT)
and manual reset (MR)
Delay Op on
A:
Output Type
DL: Open-drain, 08: 0.8V
ac ve-low
PL: Push-pull,
ac ve-low
Detect Voltage Threshold Package
DBV: SOT23
- 40 µs default
(CT pin oa ng)
- Programmable
(CT pin with capacitor
to GND)
...
54: 5.4V
DH: Open-drain,
ac ve-high
PH: Push-pull,
ac ve-high
Figure 5-1. Device Naming Nomenclature
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
3
Product Folder Links: TLV840-Q1
TLV840-Q1
SNVSBY3A – NOVEMBER 2020 – REVISED APRIL 2021
www.ti.com
6 Pin Configuration and Functions
CT
RESET / RESET
1
2
3
5
VDD
GND
MR
4
Not to scale
Figure 6-1. Pin Configuration TLV840M-Q1
DBV Package 5-Pin SOT-23
TLV840M-Q1 Top View
Table 6-1. Pin Functions
PIN
I/O
DESCRIPTION
PIN NO.
TLV840MAxL-Q1
TLV840MAxH-Q1
Active-Low Output Reset Signal: This pin is driven logic low
when VDD voltage falls below the negative voltage threshold (VIT-).
RESET remains low (asserted) for the delay time period (tD) after
1
1
RESET
N/A
O
O
VDD voltage rises above VIT+ = VIT-+VHYS
.
Active-High Output Reset Signal: This pin is driven logic high
when VDD voltage falls below the negative voltage threshold (VIT-).
RESET remains high (asserted) for the delay time period (tD) after
N/A
RESET
VDD voltage rises above VIT+ = VIT-+VHYS
.
2
3
VDD
GND
VDD
GND
I
Input Supply Voltage: TLV840-Q1 monitors VDD voltage
_
Ground
Manual Reset: Pull this pin to a logic low to assert a reset signal in
the RESET output pin. After MR pin is left floating or pulls to logic
high, the RESET output deasserts to the nominal state after the
reset delay time (tD) expires.
4
5
MR
CT
MR
CT
I
Capacitor Time Delay Pin: The CT pin offers a user-
programmable delay time. Connect an external capacitor on this
pin to adjust time delay. When not in use leave pin floating for the
smallest fixed time delay.
-
Copyright © 2021 Texas Instruments Incorporated
4
Submit Document Feedback
Product Folder Links: TLV840-Q1
TLV840-Q1
SNVSBY3A – NOVEMBER 2020 – REVISED APRIL 2021
www.ti.com
7 Specifications
7.1 Absolute Maximum Ratings
over operating free-air temperature range, unless otherwise noted(1)
MIN
MAX
UNIT
Voltage
Voltage
VDD
–0.3
6.5
V
CT, MR (2), RESET (TLV840MAPL), RESET
(TLV840MAPH)
–0.3
VDD+0.3 (3)
V
RESET (TLV840MADL)
RESET, RESET pin
–0.3
–20
–40
–65
6.5
20
Current
mA
Temperature (4)
Temperature (4)
Operating ambient temperature, TA
Storage, Tstg
125
150
℃
(1) Stresses beyond those listed under Absolute Maximum Rating may cause permanent damage to the device. These are stress
ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated
under Recommended Operating Condition. Exposure to absolute-maximum-rated conditions for extended periods may affect device
reliability.
(2) If the logic signal driving MR is less than VDD, then IDD current increases based on voltage differential.
(3) The absolute maximum rating is (VDD + 0.3) V or 6.5 V, whichever is smaller
(4) As a result of the low dissipated power in this device, it is assumed that TJ = TA.
7.2 ESD Ratings
VALUE UNIT
Human body model (HBM), per AEC Q100-002(1)
Charged device model (CDM), per AEC Q100-011
±2000
±750
V(ESD) Electrostatic discharge
V
(1) AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
7.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
NOM
MAX
UNIT
VDD (TLV840MAxL)
0.7
6
Voltage
V
CT, RESET (TLV840MAxL), RESET (TLV840MAPH) ,
MR
0
6
Current
TA
RESET and RESET pin current
Operating ambient temperature
–5
5
mA
–40
125
℃
7.4 Thermal Information
TLV840-Q1
DBV (SOT23-5)
5 PINS
193.5
THERMAL METRIC(1)
UNIT
RθJA
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
RθJC(top)
RθJB
117.9
98.5
ψJT
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
43.4
ψJB
97.8
RθJC(bot)
N/A
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
5
Product Folder Links: TLV840-Q1
TLV840-Q1
SNVSBY3A – NOVEMBER 2020 – REVISED APRIL 2021
www.ti.com
7.5 Electrical Characteristics
At 0.7 V ≤ VDD ≤ 6 V, CT = MR = Open, RESET pull-up resistor (Rpull-up) = 100 kΩ to VDD, output reset load (CLOAD) = 10 pF
and over operating free-air temperature range –40℃ to 125℃, unless otherwise noted. VDD ramp rate ≤ 100 mV/µs. Typical
values are at TA = 25℃
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
COMMON PARAMETERS
VDD
VIT–
VHYS
IDD
Input supply voltage
TLV840MAxL
0.7
–2.5
–2
6
2.5
V
%
VIT- = 0.8 V to 1.7 V
VIT- = 1.8 V to 5.4 V
±0.5
±0.5
5
Negative-going input threshold accuracy
(1)
2
Hysteresis on VIT– pin
2.5
7
%
VDD = 2 V; VIT– = 0.8 V to 1.8 V
VDD = 6 V; VIT– = 0.8 V to 5.4 V
0.12
0.15
1.0
Supply current into VDD pin (2)
µA
1.2
VMR_L
VMR_H
RMR
Manual reset logic low input (2)
Manual reset logic high input (2)
Manual reset internal pull-up resistance
CT pin internal resistance
0.3VDD
V
V
0.7VDD
100
500
kΩ
kΩ
RCT
TLV840MADL (Open-drain active-low)
VOL(max) = 300 mV
IOUT(Sink) = 15 µA
VPOR
Power on Reset Voltage (3)
700
300
300
300
mV
mV
VDD = 0.7 V, 0.8 V ≤ VIT– ≤ 1.5 V
IOUT(Sink) = 15 µA
Low level output voltage
VDD =1.5 V, 1.6 V ≤ VIT– ≤ 3.3 V
IOUT(Sink) = 500 µA
VOL
VDD = 3.3 V, 3.4 V ≤ VIT– ≤ 5.5 V
IOUT(Sink) = 2 mA
VDD = VPULLUP = 6V
TA = –40℃ to 85℃
10
10
100
350
nA
nA
Ilkg(OD)
Open-Drain output leakage current
VDD = VPULLUP = 6V
TLV840MAPL (Push-pull active-low)
VOL(max) = 300 mV
IOUT(Sink) = 15 µA
VPOR
Power on Reset Voltage (3)
Low level output voltage
700
300
300
300
mV
mV
VDD = 0.7 V, 0.8 V ≤ VIT– ≤ 1.5 V
IOUT(Sink) = 15 µA
VDD = 1.5 V, 1.6 V ≤ VIT– ≤ 3.3 V
IOUT(Sink) = 500 µA
VOL
VDD = 3.3 V, 3.4 V ≤ VIT– ≤ 5.5 V
IOUT(Sink) = 2 mA
VDD = 1.8 V, 0.8 V ≤ VIT– ≤ 1.4 V
IOUT(Source) = 500 µA
0.8VDD
0.8VDD
0.8VDD
High level output voltage
VDD = 3.3 V, 1.5 V ≤ VIT– ≤ 3.0 V
IOUT(Source) = 500 µA
VOH
V
VDD = 6 V, 3.1 V ≤ VIT– ≤ 5.5 V
IOUT(Source) = 2 mA
Copyright © 2021 Texas Instruments Incorporated
6
Submit Document Feedback
Product Folder Links: TLV840-Q1
TLV840-Q1
SNVSBY3A – NOVEMBER 2020 – REVISED APRIL 2021
www.ti.com
7.5 Electrical Characteristics (continued)
At 0.7 V ≤ VDD ≤ 6 V, CT = MR = Open, RESET pull-up resistor (Rpull-up) = 100 kΩ to VDD, output reset load (CLOAD) = 10 pF
and over operating free-air temperature range –40℃ to 125℃, unless otherwise noted. VDD ramp rate ≤ 100 mV/µs. Typical
values are at TA = 25℃
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
TLV840MAPH (Push-pull active-high)
VOH(min) = 0.8VDD
IOUT (Source) = 15 uA
V
VPOR
Power on Reset Voltage (3)
Low level output voltage
900
300
mV
mV
VDD=3.3 V
0.8 V ≤ VIT- ≤ 3.0 V
IOUT(Sink) = 500 µA
VOL
VDD=6 V
3.1 V ≤ VIT- ≤ 5.5 V
IOUT(Sink) = 2 mA
300
mV
V
VDD = 0.9 V
1 V ≤ VIT- ≤ 1.5 V
IOUT(Sink) = 15 µA
0.8VDD
0.8VDD
0.8VDD
VDD=1.5 V
1.6 V ≤ VIT- ≤ 3.3 V
IOUT(Sink) = 500 µA
High level output voltage
VOH
V
VDD=3.3 V
3.4 V ≤ VIT- ≤ 5.5 V
IOUT(Sink) = 2 mA
V
(1) VIT– threshold voltage range from 0.8 V to 5.4 V (for DL, PL versions) in 100 mV steps
(2) If the logic signal driving MR is less than VDD, then IDD current increases based on voltage differential
(3) VPOR is the minimum VDD voltage level for a controlled output state
7.6 Timing Requirements
At 0.7 V ≤ VDD ≤ 6 V, CT = MR = Open, RESET pull-up resistor (Rpull-up) = 100 kΩ to VDD, output reset load (CLOAD) = 10 pF
and over operating free-air temperature range –40℃ to 125℃, unless otherwise noted. VDD ramp rate ≤ 100 mV/µs. Typical
values are at TA = 25℃
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Propagation detect delay for VDD falling
below VIT–
VDD : (VIT+ + 10%) to (VIT– – 10%)
tP_HL
30
50
µs
(1)
CT pin = Open or NC
(VIT- - 10%) to (VIT+ + 10%)
40
80
µs
tD
Reset time delay
CT pin = 10 nF
6.2
619
10
ms
ms
µs
CT pin = 1 µF
tGI_VIT–
tSTRT
tMR_PW
tMR_RES
Glitch immunity VIT–
5% VIT– overdrive(2)
CT pin = Open or NC
Startup Delay (3)
300
µs
ns
µs
MR pin pulse duration to assert reset (4)
500
1
Propagation delay from MR low to reset
assertion
VDD = 3.3 V,
MR = VMR_H to VMR_L
VDD = 3.3 V,
MR = VMR_L to VMR_H
tMR_tD
Delay from MR release to reset deassert
tD
ms
(1) tP_HL measured from threshold trip point (VIT–) to RESET assert. VIT+ = VIT– + VHYS
(2) Overdrive % = [(VDD/ VIT–) – 1] × 100%
(3) When VDD starts from less than the specified minimum VDD and then exceeds VIT-, reset is release after the startup delay (tSTRT), a
capacitor at CT pin will add tD delay to tSTRT time
(4) Refer section on Manual Reset Input for min pulse width needed on MR pin
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
7
Product Folder Links: TLV840-Q1
TLV840-Q1
SNVSBY3A – NOVEMBER 2020 – REVISED APRIL 2021
www.ti.com
7.7 Timing Diagrams
VIT+
VIT-
VDD(MIN)
VDD
VPOR
tSTRT + tD
tP_HL
tD
tP_HL
tSTRT + tD
VOH
RESET
VOL
(1) tD (no cap) is included in tSTRT time delay. If tD delay is programmed by an external capacitor connected to CT pin then tD programmed time will be
added to the startup time, VDD slew rate = 100 mV / μs.
(2) Open-Drain timing diagram where RESET is pulled up to VDD via an external pull-up resistor
(3) RESET output is undefined when VDD is < VPOR
Figure 7-1. Timing Diagram TLV840MADL-Q1 (Open-Drain Active-Low)
VIT+
VIT-
VDD(MIN)
VDD
VPOR
tP_HL
tSTRT + tD
tD
tP_HL
tSTRT + tD
VOH
RESET
VOL
(4) tD (no cap) is included in tSTRT time delay. If tD delay is programmed by an external capacitor connected to CT pin then tD programmed time will be
added to the startup time, VDD slew rate = 100 mV / μs.
(5) RESET output is undefined when VDD is < VPOR and limited to VOL for VDD slew rate = 100 mV / μS
Figure 7-2. Timing Diagram TLV840MAPL-Q1 (Push-Pull Active-Low)
Copyright © 2021 Texas Instruments Incorporated
8
Submit Document Feedback
Product Folder Links: TLV840-Q1
TLV840-Q1
SNVSBY3A – NOVEMBER 2020 – REVISED APRIL 2021
www.ti.com
VIT+
VIT-
VDD(MIN)
VDD
VPOR
tSTRT + tD
tP_HL
tD
tP_HL
tSTRT + tD
VOH
RESET
VOL
(6) tD (no cap) is included in tSTRT time delay. If tD delay is programmed by an external capacitor connected to CT pin then tD programmed time will be
added to the startup time, VDD slew rate = 100 mV / μs.
Figure 7-3. Timing Diagram TLV840MAPH-Q1 (Push-Pull Active-High)
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
9
Product Folder Links: TLV840-Q1
TLV840-Q1
SNVSBY3A – NOVEMBER 2020 – REVISED APRIL 2021
www.ti.com
7.8 Typical Characteristics
Typical characteristics show the typical performance of the TLV840-Q1 device. Test conditions are TA = 25°C, VDD = 3.3 V,
RPull-Up = 100 kΩ, CLOAD = 50 pF, unless otherwise noted.
0.42
0.36
0.30
0.24
0.18
0.12
0.06
1.5
1.0
-40°C
25°C
125°C
VIT- = 2 V
VIT- = 3.3 V
0.5
0.0
-0.5
-1.0
-1.5
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0
VDD (V)
-40
-20
0
20
40
60
80
100 120 140
Temperature (oC)
Figure 7-4. Supply Current vs Supply Voltage
Figure 7-5. VIT- Accuracy vs Temperature
TLV840MADL13
5.6
5.2
4.8
4.4
4.0
3.6
3.2
17.5
17.0
16.5
16.0
15.5
15.0
14.5
14.0
VIT- = 2 V
VIT- = 3.3 V
-40
-20
0
20
40
60
80
100 120 140
-40
-20
0
20
40
60
80
100 120 140
Temperature (oC)
Temperature (oC)
Figure 7-6. VHYS vs Temperature
Figure 7-7. Propagation Delay vs Temperature
6000
70
60
50
40
30
20
10
TLV840MADL13
4800
3600
2400
1200
0
0
2
4
6
8
10
-40
-20
0
20
40
60
80
100 120 140
Temperature (oC)
CT Capacitance ( F)
μ
Figure 7-9. Reset Time Delay vs CT Capacitance
Figure 7-8. Reset Time Delay vs Temperature
Copyright © 2021 Texas Instruments Incorporated
10
Submit Document Feedback
Product Folder Links: TLV840-Q1
TLV840-Q1
SNVSBY3A – NOVEMBER 2020 – REVISED APRIL 2021
www.ti.com
7.8 Typical Characteristics (continued)
Typical characteristics show the typical performance of the TLV840-Q1 device. Test conditions are TA = 25°C, VDD = 3.3 V,
RPull-Up = 100 kΩ, CLOAD = 50 pF, unless otherwise noted.
0.2
0.16
0.12
0.08
0.04
0
0.10
0.09
0.08
0.07
0.06
0.05
0.04
-40oC
25oC
VIT- = 2 V
125oC
0
1
2
3
4
5
-40
-20
0
20
40
60
80
100 120 140
IOL (mA)
Temperature (oC)
Figure 7-10. VOL vs IOL
Figure 7-11. VOL vs Temperature
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
11
Product Folder Links: TLV840-Q1
TLV840-Q1
SNVSBY3A – NOVEMBER 2020 – REVISED APRIL 2021
www.ti.com
8 Detailed Description
8.1 Overview
The TLV840-Q1 is a family of nano-quiescent current voltage detectors with fixed threshold voltage. TLV840-Q1
features include programable reset time delay using external capacitor, active-low manual reset, 0.5% typical
monitor threshold accuracy with hysteresis and glitch immunity.
Fixed negative threshold voltages (VIT-) can be factory set from 0.8 V to 5.4 V. TLV840-Q1 is available in
SOT-23 5-pin industry standard package.
8.2 Functional Block Diagram
VDD
RMR
Push-pull (TLV840MAPx)
version only
VDD
MR
RESET
LOGIC
TIMER
RESET
RESET
+
–
VDD
Reference
GND
RCT
CT
GND
8.3 Feature Description
8.3.1 Input Voltage (VDD)
VDD pin is monitored by the internal comparator to indicate when VDD falls below the fixed threshold voltage.
VDD also functions as the supply for the internal bandgap, internal regulator, state machine, buffers and other
control logic blocks. Good design practice involve placing a 0.1 μF to 1 μF bypass capacitor at VDD input for
noisy applications to ensure enough charge is available for the device to power up correctly.
Copyright © 2021 Texas Instruments Incorporated
12
Submit Document Feedback
Product Folder Links: TLV840-Q1
TLV840-Q1
SNVSBY3A – NOVEMBER 2020 – REVISED APRIL 2021
www.ti.com
8.3.1.1 VDD Hysteresis
The internal comparator has built-in hysteresis to avoid erroneous output reset release. If the voltage at the VDD
pin falls below VIT- the output reset is asserted. When the voltage at the VDD pin goes above VIT- plus hysteresis
(VHYS) the output reset is deasserted after tD delay.
Hystersis Width
Hystersis Width
RESET
RESET
VIT-
VIT-
VIT+
VIT+
VDD
VDD
Figure 8-1. Hysteresis Diagram
8.3.1.2 VDD Transient Immunity
The TLV840-Q1 is immune to quick voltage transients or excursion on VDD. Sensitivity to transients depends
on both pulse duration (tGI_VIT-) found in Section 7.6 and overdrive. Overdrive is defined by how much VDD
deviates from the specified threshold. Threshold overdrive is calculated as a percent of the threshold in question,
as shown in Equation 1.
Overdrive = | [(VDD / VIT-) – 1] × 100% |
(1)
VDD
VIT+
VIT-
Overdrive
Pulse
Duration
Figure 8-2. Overdrive vs Pulse Duration
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
13
Product Folder Links: TLV840-Q1
TLV840-Q1
SNVSBY3A – NOVEMBER 2020 – REVISED APRIL 2021
www.ti.com
8.3.2 User-Programmable Reset Time Delay
The reset time delay can be set to a minimum value of 80 µs by leaving the CT pin floating, or a maximum value
of approximately 6.2 seconds by connecting 10 µF delay capacitor. The reset time delay (tD) can be programmed
by connecting a capacitor no larger than 10 µF between CT pin and GND.
The relationship between external capacitor (CCT) in µF at CT pin and the time delay (tD) in seconds is given by
Equation 2.
tD (typ) = -ln (0.29) x RCT x CCT + tD (no cap)
(2)
Equation 3 solves for external capacitor (μF) by plugging RCT and tD (CT pin = Open) given in Section 7.5
section:
CCT = (tD - 80 µs) ÷ 618937
(3)
The reset delay varies according to three variables: the external capacitor (CCT), CT pin internal resistance (RCT
)
provided in Section 7.5, and a constant. The minimum and maximum variance due to the constant is show in
Equation 4 and Equation 5:
tD (min) = -ln (0.37) x RCT (min) x CCT_EXT (min) + tD (no cap)
(4)
tD (max) = -ln (0.25) x RCT (max) x CCT_EXT (max) + tD (no cap)
(5)
The recommended maximum delay capacitor for the TLV840-Q1 is limited to 10 µF as this ensures there is
enough time for the capacitor to fully discharge when the reset condition occurs. When a voltage fault occurs,
the previously charged up capacitor discharges, and if the monitored voltage returns from the fault condition
before the delay capacitor discharges completely, the reset delay will be shorter than expected because the
delay capacitor will begin charging from a voltage above zero. Larger delay capacitors can be used so long as
the capacitor has enough time to fully discharge during the duration of the voltage fault. The amount of time
required to discharge the delay capacitor relative to the reset delay increases as VDD overdrive increases as
shown in Figure 8-3. From the graph below, to ensure the CT capacitor is fully discharged, the time period or
duration of the voltage fault needs to be greater than 10% of the programmed reset time delay.
55
25°C
50
45
40
35
30
25
20
15
10
5
0.6
0.8
1
1.2
1.4
VDD Fault Underoltage (V)
1.6
1.8
2
CTR_
Figure 8-3. CCT Discharge Time During Fault Condition (VIT- = 2 V, CCT = 1 µF)
Copyright © 2021 Texas Instruments Incorporated
14
Submit Document Feedback
Product Folder Links: TLV840-Q1
TLV840-Q1
SNVSBY3A – NOVEMBER 2020 – REVISED APRIL 2021
www.ti.com
8.3.3 Manual Reset (MR) Input
The manual reset (MR) input allows a processor GPIO or other logic circuits to initiate a reset. A logic low on MR
with pulse duration longer than tMR_PW will cause the reset output to assert. After MR returns to a logic high
(VMR_H) and VDD is above VIT+, reset is deasserted after the user programmed reset time delay (tD) expires.
The minimum duration for which MR is held under VMR_L must be at least 1% of tMR_tD. Otherwise, the effective
reset delay will be shorter roughly by the difference between 1% of tMR_tD and the actual MR pulse width. For
large capacitor based delays this difference could be noticeable unless care is taken to lengthen the MR pulse
width.
MR is internally connected to VDD through a pull-up resistor RMR shown in Section 8.2. If the logic signal
controlling MR is less than VDD, then additional current flows from VDD into MR internally. For minimum current
consumption, drive MR to either VDD or GND. VMR should not be higher than VDD voltage.
VIT+
VHYS
VIT-
VIT+
VHYS
VIT-
VDD
tP_HL
tD
tMR_tD
RESET
(2)
tMR_RES
VMR_H
VMR_L
MR
(1)
tMR_PW
Time
(1) MR pulse width too small to assert RESET
(2) MR voltage not low enough to assert RESET
Figure 8-4. Timing Diagram MR and RESET
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
15
Product Folder Links: TLV840-Q1
TLV840-Q1
SNVSBY3A – NOVEMBER 2020 – REVISED APRIL 2021
www.ti.com
8.3.4 Output Logic
8.3.4.1 RESET Output, Active-Low
RESET (Active-Low) applies to TLV840DL-Q1 (Open-Drain) and TLV840PL-Q1 (Push-Pull) hence the "L" in the
device name. RESET remains high (deasserted) as long as VDD is above the negative threshold (VIT-) and the
MR pin is floating or above VMR_H. If VDD falls below the negative threshold (VIT-) or if MR is driven low, then
RESET is asserted.
When MR is again logic high or floating and VDD rise above VIT+, the delay circuit will hold RESET low for the
specified reset time delay (tD). When the reset time delay has elapsed, the RESET pin goes back to logic high
voltage (VOH).
The TLV840DL-Q1 (Open-Drain) version, denoted with "D" in the device name, requires an external pull-up
resistor to hold RESET pin high. Connect the external pull-up resistor to the desired pull-up voltage source and
RESET can be pulled up to any voltage up to 6.5 V independent of the VDD voltage. To ensure proper voltage
levels, give some consideration when choosing the pull-up resistor values. The external pull-up resistor value
determines the actual VOL, the output capacitive loading, and the output leakage current (Ilkg(OD)).
The Push-Pull variants (TLV840PL-Q1 and TLV840PH-Q1), denoted with "P" in the device name, does not
require an external pull-up resistor.
8.3.4.2 RESET Output, Active-High
RESET (Active-High), denoted with no bar above the pin label, applies to TLV840DH-Q1 (Open-Drain)
and TLV840PH-Q1 push-pull active-high version, hence the "H" in the device name. RESET remains low
(deasserted) as long as VDD is above the negative threshold (VIT-) and the MR pin is floating or above VMR_H. If
VDD falls below the negative threshold (VIT-) or if MR is driven low, then RESET is asserted driving the RESET
pin to high voltage (VOH).
When MR is again logic high or floating and VDD rise above VIT+ the delay circuit will hold RESET high for the
specified reset time delay (tD). When the reset time delay has elapsed, the RESET pin goes back to logic low
voltage (VOL).
The TLV840DH-Q1 (Open-Drain) version, denoted with "D" in the device name, requires an external pull-up
resistor to hold RESET pin high. Connect the external pull-up resistor to the desired pull-up voltage source and
RESET can be pulled up to any voltage up to 6.5 V independent of the VDD voltage. To ensure proper voltage
levels, give some consideration when choosing the pull-up resistor values. The external pull-up resistor value
determines the actual VOL, the output capacitive loading, and the output leakage current (Ilkg(OD)).
The Push-Pull variants (TLV840PL-Q1 and TLV840PH-Q1), denoted with "P" in the device name, does not
require an external pull-up resistor.
Copyright © 2021 Texas Instruments Incorporated
16
Submit Document Feedback
Product Folder Links: TLV840-Q1
TLV840-Q1
SNVSBY3A – NOVEMBER 2020 – REVISED APRIL 2021
www.ti.com
8.4 Device Functional Modes
Table 8-1 summarizes the various functional modes of the device. Logic high is represented by "H" and logic low
is represented by "L".
Table 8-1. Truth Table
VDD
VDD < VPOR
VPOR < VDD < VIT-
VDD ≥ VIT-
MR
Ignored
Ignored
L
RESET
RESET
Undefined
Undefined
H
H
L
L
L
VDD ≥ VIT-
H
H
H
VDD ≥ VIT-
Floating
L
8.4.1 Normal Operation (VDD > VPOR
)
When VDD is greater than VPOR, the reset signal is determined by the voltage on the VDD pin with respect to the
trip point (VIT-)
•
•
MR high: the reset signal corresponds to VDD with respect to the threshold voltage.
MR low: in this mode, the reset is asserted regardless of the threshold voltage.
8.4.2 Below Power-On-Reset (VDD < VPOR
)
When the voltage on VDD is lower than VPOR, the device does not have enough bias voltage to internally pull the
asserted output low or high and reset voltage level is undefined.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
17
Product Folder Links: TLV840-Q1
TLV840-Q1
SNVSBY3A – NOVEMBER 2020 – REVISED APRIL 2021
www.ti.com
9 Application and Implementation
Note
Information in the following applications sections is not part of the TI component specification, and
TI does not warrant its accuracy or completeness. TI’s customers are responsible for determining
suitability of components for their purposes. Customers should validate and test their design
implementation to confirm system functionality.
9.1 Application Information
The following sections describe in detail how to properly use this device, depending on the requirements of the
final application.
9.2 Typical Application
9.2.1 Design 1: Dual Rail Monitoring with Power-up Sequencing
A typical application for the TLV840-Q1 is voltage rail monitoring and power-up sequencing as shown in
Figure 9-1. The TLV840-Q1 can be used to monitor any rail above 0.9 V. In this design application, two
TLV840-Q1 devices monitor two separate voltage rails and sequences the rails upon power-up. The
TLV840MAPL29-Q1 is used to monitor the 3.3-V main power rail and the TLV840MADL10-Q1 is used to monitor
the 1.2-V rail provided by the LDO for other system peripherals. The RESET output of the TLV840MAPL29-Q1 is
connected to the enable (EN) input of the LDO. A reset event is initiated on either voltage supervisor when the
VDD voltage is less than VIT-. For a system-wide reset event, both MR pins are tied to the SYS_RST. For the
purpose of this application, the design detail on MR are not covered. For more information on the function of MR,
please see Section 8.3.3
LDO
1.2 V
IN
OUT
3.3 V
EN
49.9 k
1
F
1 F
VCORE
Microcontroller
VI/O
VDD
VDD
CT
CT
RESET
RESET
RESET
NC
TLV840MAPL29-Q1
TLV840MADL10-Q1
0.047
F
MR
MR
GND
GND
SYS_RST
Figure 9-1. TLV840-Q1 Voltage Rail Monitor and Power-Up Sequencer Design Block Diagram
Copyright © 2021 Texas Instruments Incorporated
18
Submit Document Feedback
Product Folder Links: TLV840-Q1
TLV840-Q1
SNVSBY3A – NOVEMBER 2020 – REVISED APRIL 2021
www.ti.com
9.2.1.1 Design Requirements
This design requires voltage supervision on two separate rails: 3.3-V and 1.2-V rails. The voltage rail needs to
sequence upon power up with the 3.3-V rail coming up first followed by the 1.2-V rail at least 25 ms after.
PARAMETER
DESIGN REQUIREMENT
DESIGN RESULT
Two TLV840-Q1 devices provide voltage
monitoring with 1% accuracy with device options
available in 0.1 V variations
Two Rail Voltage Supervision
Monitor 3.3-V and 1.2-V rails
Power up the 3.3-V rail first followed by 1.2-V rail
25 ms after
The CT capacitor on TLV840MAPL29-Q1 is set to
0.047 µF for a reset time delay of 29 ms typical
Voltage Rail Sequencing
Maximum device current
consumption
1 µA
Each TLV840-Q1 requires 120 nA typical
9.2.1.2 Detailed Design Procedure
The primary constraint for this application is choosing the correct device to monitor the supply voltage of the
microprocessor. The TLV840-Q1 can monitor any voltage between 0.8 V and 5.4 V. Depending on how far
away from the nominal voltage rail the user wants the voltage supervisor to trigger determines the correct
voltage supervisor variant to choose. In this example, the first TLV840-Q1 triggers when the 3.3-V rail falls to
2.9 V. The second TLV840-Q1 triggers a reset when the 1.2-V rail falls to 0.9 V. The secondary constraint
for this application is the reset time delay that must be at least 25 ms to allow the microprocessor, and all
other devices using the 3.3-V rail, enough time to startup correctly before the 1.2-V rail is enabled via the
LDO. Because a minimum time is required, the user must account for capacitor tolerance. For applications with
ambient temperatures ranging from –40°C to +125°C, CCT can be calculated using RCT and solving for CCT in
Equation 2. Solving Equation 2 for 25 ms gives a minimum capacitor value of 0.0403 µF which is rounded up to
a standard value 0.047 µF to account for capacitor tolerance.
A 1 µF decoupling capacitor is connected to the VDD pin as a good analog design practice. The pull-up resistor
is only required for the Open-Drain device variants and is calculated to ensure that VOL does not exceed max
limit given the Isink possible at the expected supply voltage. In this design example nominal VDD is 1.2 V but
dropping to 0.9 V. In Section 7.5, max VOL provides 15 µA I sink for 0.7 V VDD, which is the closest voltage to
this design example. Using 15 µA of Isink and 300 mV max VOL, gives us 40 kΩ for the pull-up resistor. Any
value higher than 40 kΩ would ensure that VOL will not exceed 300 mV max specification.
9.2.1.3 Application Curves
VDD
30ms delay from VDD (3.3 V) to LDO Enable set by 0.047 µF on CT of TLV840MAPL29-Q1
RESET
(LDO Enable)
VOUT (LDO)
Negligible delay from LDO Enable to 1.2 V V
OUT
Figure 9-2. Startup Sequence Highlighting the Delay Between 3.3 V and 1.2 V Rails
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
19
Product Folder Links: TLV840-Q1
TLV840-Q1
SNVSBY3A – NOVEMBER 2020 – REVISED APRIL 2021
www.ti.com
9.2.2 Application Curve: Adjusting Output Reset Delay on TLV840EVM
These application curves are taken with the TLV840EVM and they display a change in reset delay time with
different capacitor values. The output reset delay time was designed with the ease of programability for the
customer. Figure 9-3 displays an output reset delay time of 57.6 μs with no capacitor on the CT pin. Figure 9-4
and Figure 9-5 have output reset delay times of 5.42 ms and 56.8 ms, respectively. Both the output delay times
and capacitors used resulted in an order of magnitude difference. Please see the TLV840EVM User Guide for
more information.
VDD
VDD
Reset Delay (tD)= 57.6 µs
Reset Delay (tD)= 5.42 ms
RESET
RESET
Figure 9-4. TLV840EVM RESET Time Delay (tD) with
0.01-µF Capacitor
Figure 9-3. TLV840EVM RESET Time Delay (tD) with
No Capacitor
VDD
Reset Delay (tD)= 56.8 ms
RESET
Figure 9-5. TLV840EVM RESET Time Delay (tD) with 0.1-µF Capacitor
Copyright © 2021 Texas Instruments Incorporated
20
Submit Document Feedback
Product Folder Links: TLV840-Q1
TLV840-Q1
SNVSBY3A – NOVEMBER 2020 – REVISED APRIL 2021
www.ti.com
10 Power Supply Recommendations
The TLV840 is designed to operate from an input supply with a voltage range between 0.7 V and 6 V. TI
recommends an input supply capacitor between the VDD pin and GND pin. This device has a 6.5 V absolute
maximum rating on the VDD pin. If the voltage supply providing power to VDD is susceptible to any large voltage
transient that can exceed 6.5 V, additional precautions must be taken.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
21
Product Folder Links: TLV840-Q1
TLV840-Q1
SNVSBY3A – NOVEMBER 2020 – REVISED APRIL 2021
www.ti.com
11 Layout
11.1 Layout Guidelines
Make sure that the connection to the VDD pin is low impedance. Good analog design practice recommends
placing a minimum 0.1 µF ceramic capacitor as near as possible to the VDD pin. If a capacitor is not connected
to the CT pin, then minimize parasitic capacitance on this pin so the rest time delay is not adversely affected.
•
•
•
Make sure that the connection to the VDD pin is low impedance. Good analog design practice is to place a >
0.1 µF ceramic capacitor as near as possible to the VDD pin.
If a CCT capacitor is used, place these components as close as possible to the CT pin. If the CT pin is left
unconnected, make sure to minimize the amount of parasitic capacitance on the pin to < 5 pF.
Place the pull-up resistors on RESET pin as close to the pin as possible.
11.2 Layout Example
The layout example in shows how the TLV840DL-Q1 is laid out on a printed circuit board (PCB) with a user-
defined delay.
Pull-up resistor required for Open-Drain
(TLV840MADx-Q1) only
CT
RESET
CCT
Rpull-up
VDD
GND
CIN
MR
VDD
GND
Vias used to connect pins for application - specific connections
Figure 11-1. TLV840M-Q1 Recommended Layout
Copyright © 2021 Texas Instruments Incorporated
22
Submit Document Feedback
Product Folder Links: TLV840-Q1
TLV840-Q1
SNVSBY3A – NOVEMBER 2020 – REVISED APRIL 2021
www.ti.com
12 Device and Documentation Support
12.1 Device Nomenclature
Table 12-1 shows how to decode the function of the device based on its part number
Table 12-1. Device Naming Convention
DESCRIPTION
Generic Part number
NOMENCLATURE
VALUE
TLV840
M 1
A
TLV840
Feature Option
Manual Reset option in addition to CT pin
40 µs (Default internal reset time delay)
Open-Drain, Active-Low
Push-Pull, Active-Low
Delay Option
Variant code (Output Topology)
DL
PL
DH
PH
Open-Drain, Active-High
Push-Pull, Active-High
Example: 12 stands for 1.2 V threshold
SOT23-5
Detect Voltage Option
Package
## (two characters)
DBV
R
Reel
Large Reel
Automotive Version
Q1
AEC-Q100
1. Orderable part numbers with TLV840M-Q1 are only available with the delay option A. However, longer
delays can be achieved through an external capacitor on the CT pin. Leaving the CT pin floating will result in
typical 40 μs delay feature option.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
23
Product Folder Links: TLV840-Q1
TLV840-Q1
SNVSBY3A – NOVEMBER 2020 – REVISED APRIL 2021
www.ti.com
12.2 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. In the upper
right corner, click on Alert me to register and receive a weekly digest of any product information that has
changed. For change details, review the revision history included in any revised document.
12.3 Support Resources
12.4 Trademarks
All trademarks are the property of their respective owners.
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2021 Texas Instruments Incorporated
24
Submit Document Feedback
Product Folder Links: TLV840-Q1
PACKAGE OPTION ADDENDUM
www.ti.com
26-Aug-2021
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
TLV840MADL12DBVRQ1
TLV840MADL22DBVRQ1
TLV840MADL30DBVRQ1
TLV840MADL31DBVRQ1
TLV840MADL32DBVRQ1
TLV840MADL40DBVRQ1
TLV840MAPH29DBVRQ1
TLV840MAPL36DBVRQ1
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
DBV
DBV
DBV
DBV
DBV
DBV
DBV
DBV
5
5
5
5
5
5
5
5
3000 RoHS & Green
3000 RoHS & Green
3000 RoHS & Green
3000 RoHS & Green
3000 RoHS & Green
3000 RoHS & Green
3000 RoHS & Green
3000 RoHS & Green
NIPDAU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
2HNF
2HOF
2HPF
2HMF
2HQF
2HDF
2INF
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
2HVF
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
26-Aug-2021
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TLV840-Q1 :
Catalog : TLV840
•
NOTE: Qualified Version Definitions:
Catalog - TI's standard catalog product
•
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
27-Aug-2021
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TLV840MADL12DBVRQ1 SOT-23
TLV840MADL22DBVRQ1 SOT-23
TLV840MADL30DBVRQ1 SOT-23
TLV840MADL31DBVRQ1 SOT-23
TLV840MADL32DBVRQ1 SOT-23
TLV840MADL40DBVRQ1 SOT-23
TLV840MAPH29DBVRQ1 SOT-23
TLV840MAPL36DBVRQ1 SOT-23
DBV
DBV
DBV
DBV
DBV
DBV
DBV
DBV
5
5
5
5
5
5
5
5
3000
3000
3000
3000
3000
3000
3000
3000
180.0
180.0
180.0
180.0
180.0
180.0
180.0
180.0
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
3.2
3.2
3.2
3.2
3.2
3.2
3.2
3.2
3.2
3.2
3.2
3.2
3.2
3.2
3.2
3.2
1.4
1.4
1.4
1.4
1.4
1.4
1.4
1.4
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
Q3
Q3
Q3
Q3
Q3
Q3
Q3
Q3
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
27-Aug-2021
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TLV840MADL12DBVRQ1
TLV840MADL22DBVRQ1
TLV840MADL30DBVRQ1
TLV840MADL31DBVRQ1
TLV840MADL32DBVRQ1
TLV840MADL40DBVRQ1
TLV840MAPH29DBVRQ1
TLV840MAPL36DBVRQ1
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
SOT-23
DBV
DBV
DBV
DBV
DBV
DBV
DBV
DBV
5
5
5
5
5
5
5
5
3000
3000
3000
3000
3000
3000
3000
3000
210.0
210.0
210.0
210.0
210.0
210.0
210.0
210.0
185.0
185.0
185.0
185.0
185.0
185.0
185.0
185.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
Pack Materials-Page 2
PACKAGE OUTLINE
DBV0005A
SOT-23 - 1.45 mm max height
S
C
A
L
E
4
.
0
0
0
SMALL OUTLINE TRANSISTOR
C
3.0
2.6
0.1 C
1.75
1.45
1.45
0.90
B
A
PIN 1
INDEX AREA
1
2
5
2X 0.95
1.9
3.05
2.75
1.9
4
3
0.5
5X
0.3
0.15
0.00
(1.1)
TYP
0.2
C A B
0.25
GAGE PLANE
0.22
0.08
TYP
8
0
TYP
0.6
0.3
TYP
SEATING PLANE
4214839/F 06/2021
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. Refernce JEDEC MO-178.
4. Body dimensions do not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.25 mm per side.
www.ti.com
EXAMPLE BOARD LAYOUT
DBV0005A
SOT-23 - 1.45 mm max height
SMALL OUTLINE TRANSISTOR
PKG
5X (1.1)
1
5
5X (0.6)
SYMM
(1.9)
2
3
2X (0.95)
4
(R0.05) TYP
(2.6)
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:15X
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
METAL
EXPOSED METAL
EXPOSED METAL
0.07 MIN
ARROUND
0.07 MAX
ARROUND
NON SOLDER MASK
DEFINED
SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK DETAILS
4214839/F 06/2021
NOTES: (continued)
5. Publication IPC-7351 may have alternate designs.
6. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
DBV0005A
SOT-23 - 1.45 mm max height
SMALL OUTLINE TRANSISTOR
PKG
5X (1.1)
1
5
5X (0.6)
SYMM
(1.9)
2
3
2X(0.95)
4
(R0.05) TYP
(2.6)
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE:15X
4214839/F 06/2021
NOTES: (continued)
7. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
8. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party
intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages,
costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (https:www.ti.com/legal/termsofsale.html) or other applicable terms available either
on ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s
applicable warranties or warranty disclaimers for TI products.IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2021, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明