TPS25850-Q1 [TI]
具有可编程电流限制和热管理功能的双路 3A USB Type-C 充电端口控制器;型号: | TPS25850-Q1 |
厂家: | TEXAS INSTRUMENTS |
描述: | 具有可编程电流限制和热管理功能的双路 3A USB Type-C 充电端口控制器 控制器 |
文件: | 总65页 (文件大小:5837K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
具有热管理功能和可编程电流限制的TPS2585x-Q1 2.2MHz 低EMI 双路3A USB
Type-C® 充电端口转换器
• 符合USB-IF 标准
1 特性
– Type-C 1.3 版
• 符合面向汽车应用的AEC-Q100 标准:
• 在CC 上具有3A 电流通告能力
– 温度等级1:TA 范围–40°C 至+125°C
– HBM ESD 分类等级H2
– CDM ESD 分类等级C5
• VBUS 应用和放电
• VCONN 拉电流:200mA
• USB 电缆极性检测(POL) (TPS25851-Q1)
• 针对超低EMI 要求进行了优化:
– 自动DCP 模式(TPS25850-Q1):
– 符合CISPR25 5 类标准
• 符合BC1.2 和YD/T 1591 2009 要求的短路
模式
• 1.2V 模式
– HotRod™ 封装可更大限度地减少开关节点振铃
– 展频可降低峰值发射
• 同步降压稳压器
• 2.7V 分压器3 模式
– 在2.1MHz 下具有高效率:VIN = 13.5V、
IPA_BUS = 3A 且IPB_BUS = 3A 时效率为93.4%
– 18mΩ/10mΩ 低RDS(ON) 降压稳压器MOSFET
– 工作电压范围:5.5V 至26V,可承受36V 输入
– 频率可调节:200kHz 至3MHz
– 具有展频频谱抖动的FPWM
• 甩负荷和可编程TA
• 器件TJ 范围:–40°C 至+150°C
• 故障标志报告(TPS25851-Q1 和TPS25852-
Q1):USB 过流、热关断
• USB 端口开/关控制(TPS25852-Q1)
2 应用
– 可选输出电压:5.1V、5.17V、5.3V、5.4V
• 内部电源路径:
• 汽车USB 充电端口
• 汽车USB 媒体中心
– 7mΩ/7mΩ 低RDS(ON) 内部USB 功率MOSFET
– USB 端口的高精度可编程电流限制:3.4A 下为
±10%
3 说明
TPS258x-Q1 是一款集成式 USB 充电端口解决方案,
其中包括一个能够提供最大6.6A 电流的同步直流/直流
转换器,而且它还集成了检测和控制功能,可充当
USB 电池充电1.2 和Type-C 端口。
– OUT:用于辅助负载的5.1V、200mA 电源
• 线路压降补偿:2.4A 负载下为90mV
器件信息(1)
器件型号
封装
封装尺寸(标称值)
3.50mm × 4.50mm
3.50mm × 4.50mm
3.50mm × 4.50mm
TPS25850-Q1
TPS25851-Q1
TPS25852-Q1
VQFN-HR (25)
VQFN-HR (25)
VQFN-HR (25)
(1) 如需了解所有不同可用选件的详细器件型号,请参阅数据表末
尾的可订购产品附录。
100
95
90
85
80
75
70
BOOT
SW
BATT
IN
SENSE
SENSE
BIAS
OUT
SENSE
SENSE
EN/UV
PA_BUS
PA_DP
PA_DM
PA_CC1
PA_CC2
TPS25850-Q1
TS
VIN=6V
2.1MHz
65
60
VIN=13.5V 2.1MHz
VIN=18V 2.1MHz
PB_CC2
PB_CC1
ILIM
FREQ/SYNC
VSET
0.1
1
2
3
4
5
6
PB_DM
PB_DP
Load Current(A)
PB_BUS
效率与输出电流间的关系
简化版原理图TPS25850-Q1
本文档旨在为方便起见,提供有关TI 产品中文版本的信息,以确认产品的概要。有关适用的官方英文版本的最新信息,请访问
www.ti.com,其内容始终优先。TI 不保证翻译的准确性和有效性。在实际设计之前,请务必参考最新版本的英文版本。
English Data Sheet: SLVSEM3
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
Table of Contents
10.2 Functional Block Diagram.......................................24
10.3 Feature Description.................................................25
10.4 Device Functional Modes........................................42
11 Application and Implementation................................ 43
11.1 Application Information............................................43
11.2 Typical Applications.................................................43
12 Power Supply Recommendations..............................52
13 Layout...........................................................................52
13.1 Layout Guidelines................................................... 52
13.2 Layout Example...................................................... 53
13.3 Ground Plane and Thermal Considerations............53
14 Device and Documentation Support..........................55
14.1 接收文档更新通知................................................... 55
14.2 支持资源..................................................................55
14.3 Trademarks.............................................................55
14.4 Electrostatic Discharge Caution..............................55
14.5 术语表..................................................................... 55
15 Mechanical, Packaging, and Orderable
1 特性................................................................................... 1
2 应用................................................................................... 1
3 说明................................................................................... 1
4 Revision History.............................................................. 2
5 说明(续).........................................................................3
6 Device Comparison Table...............................................4
7 Pin Configuration and Functions...................................5
8 Specifications.................................................................. 9
8.1 Absolute Maximum Ratings ....................................... 9
8.2 ESD Ratings .............................................................. 9
8.3 Recommended Operating Conditions ......................10
8.4 Thermal Information .................................................11
8.5 Electrical Characteristics ..........................................11
8.6 Timing Requirements ...............................................14
8.7 Switching Characteristics .........................................15
8.8 Typical Characteristics..............................................17
9 Parameter Measurement Information..........................22
10 Detailed Description....................................................23
10.1 Overview.................................................................23
Information.................................................................... 56
4 Revision History
注:以前版本的页码可能与当前版本的页码不同
Changes from Revision C (March 2021) to Revision D (September 2021)
Page
• 添加了TSP25851-Q1 和TPS25852-Q1 信息.................................................................................................... 1
Changes from Revision B (October 2020) to Revision C (March 2021)
Page
• 向特性部分添加了EMI 要求要点....................................................................................................................... 1
• 更新了文档标题...................................................................................................................................................1
• Added 图11-4 to the Application Curves section............................................................................................. 47
Changes from Revision A (June 2020) to Revision B (October 2020)
Page
• 更新了整个文档中的表格、图和交叉参考的编号格式.........................................................................................1
• 将状态从“预告信息”更改为“量产数据”....................................................................................................... 1
Changes from Revision * (May 2020) to Revision A (June 2020)
Page
• Updated IN pin description................................................................................................................................. 5
• Added USB Port Operating Modes ..................................................................................................................39
• Added Device Functional Modes .....................................................................................................................42
Copyright © 2021 Texas Instruments Incorporated
2
Submit Document Feedback
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
5 说明(续)
TPS2585x-Q1 是高度集成的USB Type-C® 充电控制器系列,适用于双USB 端口应用。
该系列器件集成了一个具有内部功率MOSFET 的单片、同步、整流、降压开关模式转换器和两个具有充电端口自
动检测功能的 USB 限流开关。TPS2585x-Q1 提供了一种紧凑型解决方案,可在宽输入电源电压范围内实现6.6A
的连续输出电流以及出色的负载和线路调节。该同步降压稳压器具有峰值电流模式控制,而且采用了内部补偿,
可简化设计。FREQ 引脚上有一个电阻器,可用于在 200kHz 和 3MHz 之间设置开关频率。在低于 400kHz 的频
率下运行可实现更高的系统效率,在高于 2.1MHz 的频率下运行则可以避开 AM 无线电频带,并且能够使用较小
的电感器。
TPS2585x-Q1 集成了标准USB Type-C 端口控制器功能,包括用于3A 和1.5A 电流广播的配置通道(CC) 逻辑。
电池充电(1.2 版)集成提供了利用 USB 数据线信号来确定 USB 端口拉电流能力的传统非 Type-C USB 设备所
需的电气特性。TPS2585x-Q1 还集成了VCONN 电源,可满足USB3.1 电源要求。由于系统集成度高且占用空间
小,该器件特别适用于双端口应用。
TPS2585x-Q1 支持智能热管理。USB 输出电压和 Type-C 电流广播可以根据温度感应通过TS 引脚进行调节。它
必须在 TS 引脚上连接一个 NTC 热敏电阻以监控环境温度或 PCB 板温度,具体取决于 NTC 热敏电阻在 USB 充
电模块或PCB 板中的放置位置。选择不同的NTC 热敏电阻和底部串联电阻可以改变切负荷的温度阈值。
TPS2585x-Q1 具有四种可选的 USB 输出电压设置:5.1V、5.17V、5.3V 和 5.4V。TPS2585x-Q1 集成了一个精
密电流检测放大器,用于实现电缆压降补偿和用户可编程电流限制调整。电缆补偿仅在输出电压设置为 5.17V 时
可用。在输出电流为 2.4A 时,电缆补偿电压为 90mV。电缆补偿可使降压稳压器输出电压随负载电流线性改变,
以抵消由于汽车电缆布线中的导线电阻引起的压降,从而帮助便携式设备在重载下实现更理想的电流和电压充
电。无论负载电流如何,在连接的便携式器件上测得的总线电压都保持大致恒定,这样,便携式器件的电池充电
器就能够保持理想工作状态。
TPS2585x-Q1 提供针对 USB 充电和系统运行的多种安全特性,包括外部负热敏电阻监控、逐周期电流限制、断
续短路保护、欠压锁定、总线过流、输出过流以及裸片过热保护。
该器件系列采用25 引脚3.5mm x 4.5mm QFN 封装。
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
3
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
6 Device Comparison Table
DEVICE NUMBER
Type-C ports number
TPS25850-Q1
TPS25851-Q1
TPS25852-Q1
Dual
Dual
Dual
Support Type-C protocol
NTC Thermistor Input (TS)
USB load switch ON/OFF control
Fault event indication
Yes
Yes
Yes
Yes
Yes
Yes
No
No
Yes
No
Yes
Yes
Thermal warning indication
External clock synchronization
BC1.2 DCP
No
No
No
Yes
Yes
Yes
Yes
No
No
Apple or Samsung charging scheme
Cable compensation
Yes
No
No
Yes(1)
Yes(1)
Yes(1)
Selectable output voltage
Adjustable output short current limit
FPWM/PFM
Yes
Yes
Yes
Yes
Yes
Yes
FPWM
FPWM
FPWM
DCDC always ON (EN pull High)
Spread spectrum
No
Yes
Yes
Yes
Yes
Yes
Package
QFN-25 3.5 mm × 4.5 mm
QFN-25 3.5 mm × 4.5 mm
QFN-25 3.5 mm × 4.5 mm
(1) VSET short to GND to set 5.17-V output voltage. Compensation voltage is 90 mV when either USB port A or USB port B output 2.4-A
current.
Copyright © 2021 Texas Instruments Incorporated
4
Submit Document Feedback
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
7 Pin Configuration and Functions
PGND SW
IN
BOOT
21
VSET
1
24
23
22
TS
BIAS
EN/UV
2
20
3
FREQ/SYNC
PB_DP
19
18
PA_DP
4
5
PA_DM
PB_DM
PGND
17
16
25
11
6
7
AGND
PB_CC1
PB_CC2
PA_CC1
15
14
PA_CC2
8
10
12
9
13
ILIM
PB_BUS
OUT
PA_BUS SENSE
图7-1. TPS25850-Q1 RPQ Package 25-Pin (QFN) Top View
VSET
1
PGND SW
IN
BOOT
21
24
23
22
TS
BIAS
EN/UV
2
3
20
19
FREQ/SYNC
4
5
18 /PB_FAULT
17 /PB_POL
/PA_FAULT
/PA_POL
25
11
PGND
6
7
16
AGND
PB_CC1
PB_CC2
PA_CC1
15
14
PA_CC2
8
10
12
9
13
ILIM
PB_BUS
OUT
PA_BUS SENSE
图7-2. TPS25851-Q1 RPQ Package 25-Pin (QFN) Top View
PGND SW
IN
BOOT
21
VSET
1
24
23
22
TS
BIAS
EN/UV
2
3
20
19
FREQ/SYNC
4
5
18 /PB_FAULT
17 PB_EN
/PA_FAULT
PA_EN
25
11
PGND
6
7
16
AGND
PB_CC1
PB_CC2
PA_CC1
15
14
PA_CC2
8
10
12
9
13
ILIM
PB_BUS
OUT
PA_BUS SENSE
图7-3. TPS25852-Q1 RPQ Package 25-Pin (QFN) Top View
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
5
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
表7-1. Pin Functions for TPS25850-Q1 RPQ Package
NAME
NO.
TYPE (1)
DESCRIPTION
Output Voltage Setting. Short to GND to set the 5.17-V output voltage. Float or pull up to
VSENSE to set 5.1-V output voltage. Tie to GND through a 40.2-KΩ resistor to set 5.3-V
output voltage. Tie to GND through a 80.6-KΩ resistor to set 5.4-V output voltage.
VSET
1
A
TS
2
3
A
P
Temperature Sense terminal. Connect the TS input to the NTC thermistor.
Input of internal bias supply. Must connect to the SENSE pin directly. Power the internal
circuit.
BIAS
PA_DP
PA_DM
AGND
4
5
6
7
8
A
A
P
A
A
D+ data line. Connect to USB Port A connector.
D- data line. Connect to USB Port A connector.
Analog ground terminal. Connect AGND to PGND.
Connect to Type-C Port A CC1 pin. Analog input, output, or both.
Connect to Type-C Port A CC2 pin. Analog input, output, or both.
PA_CC1
PA_CC2
Current Limit program. Connect a resistor to set the current limit threshold. Short to GND
to set the default 3.55-A current limit.
ILIM
9
A
P
P
P
P
PA_BUS
SENSE
PB_BUS
OUT
10
11
12
13
Port A BUS output.
Output Voltage Sensing. External load on this pin is strictly prohibited. Connect to the
other side of the external inductor.
Port B BUS output.
Output pin. Provide 5.1-V voltage to power external load with max 200-mA capability. The
voltage follows the VSET setting.
PB_CC2
PB_CC1
14
15
A
A
Connect to Type-C Port B CC2 pin. Analog input, output, or both.
Connect to Type-C Port B CC1 pin. Analog input, output, or both.
Power Ground terminal. Connected to the source of LS FET internally. Connect to system
ground, AGND, and the ground side of the CIN and COUT capacitors. The path to CIN must
be as short as possible.
PGND
16,24,25
P
PB_DM
PB_DP
17
18
A
A
D–data line. Connect to USB port B connector.
D+ data line. Connect to USB port B connector.
Switching Frequency Program and External Clock Input. Connect a resistor from FREQ to
GND to set the switching frequency.
FREQ/ SYNC
EN/UV
BOOT
IN
19
20
21
22
23
A
A
P
P
P
Enable pin. Precision enable controls the regulator switching action and type-C. Do not
float. High = on, Low = off. Can be tied to SENSE directly. Precision enable input allows
adjustable UVLO by external resistor divider if tie to IN pin.
Bootstrap capacitor connection. Internally, the BOOT connects to the cathode of the
boost-strap diode. Connect the 0.1-μF bootstrap capacitor from SW to BOOT.
Input power. Connected to external DC supply. Expected range of bypass capacitors is 1
μF to 10 μF, connect from IN to PGND. Can withstand up to 36 V without damage but
operating is suspended if VIN is above the 26-V OVP threshold.
Switching output of the regulator. Internally connected to source of the HS FET and drain
of the LS FET. Connect to output inductor.
SW
(1) A = Analog, P = Power, G = Ground.
表7-2. Pin Functions for TPS25851-Q1 RPQ Package
NAME
NO.
TYPE (1)
DESCRIPTION
Output voltage setting. Short to GND to set the 5.17-V output voltage. Float or pull up to
VSENSE to set 5.1-V output voltage. Tie to GND through a 40.2-KΩ resistor to set 5.3-V
output voltage. Tie to GND through a 80.6-KΩ resistor to set 5.4-V output voltage.
VSET
1
A
TS
2
3
A
P
Temperature Sense terminal. Connect the TS input to the NTC thermistor.
Input of internal bias supply. Must connect to the SENSE pin directly. Power the internal
circuit.
BIAS
USB Port A Fault indication. /PA_FAULT indicates overcurrent on PA_BUS or
overtemperature conditions. /PA_FAULT is an open drain in normal conditions. Pull /
PA_FAULT low during fault conditions.
PA_FAULT
4
A
Copyright © 2021 Texas Instruments Incorporated
6
Submit Document Feedback
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
表7-2. Pin Functions for TPS25851-Q1 RPQ Package (continued)
NAME
NO.
TYPE (1)
DESCRIPTION
Polarity open-drain logic output. Signals which Type-C CC pin is connected to the CC line.
This gives the information needed to mux the super speed lines. Asserted when the Port A
CC2 pin is connected to the CC line in cable.
PA_POL
5
A
AGND
PA_CC1
PA_CC2
6
7
8
P
A
A
Analog ground terminal. Connect AGND to PGND.
Connect to Type-C Port A CC1 pin. Analog input, output, or both.
Connect to Type-C Port A CC2 pin. Analog input, output, or both.
Current Limit program. Connect a resistor to set the current limit threshold. Short to GND
to set the default 3.55-A current limit.
ILIM
9
A
P
P
P
P
PA_BUS
SENSE
PB_BUS
OUT
10
11
12
13
Port A BUS output.
Output Voltage Sensing. External load on this pin is strictly prohibited. Connect to the
other side of the external inductor.
Port B BUS output.
Output pin. Provide 5.1-V voltage to power external load with max 200-mA capability. The
voltage follows the VSET setting.
PB_CC2
PB_CC1
14
15
A
A
Connect to Type-C Port B CC2 pin. Analog input, output, or both.
Connect to Type-C Port B CC1 pin. Analog input, output, or both.
Power Ground terminal. Connected to the source of LS FET internally. Connect to system
ground, AGND, and the ground side of the CIN and COUT capacitors. Path to CIN must be
as short as possible.
PGND
16,24,25
17
P
A
Polarity open-drain logic output. Signals which Type-C CC pin is connected to the CC line.
This gives the information needed to mux the super speed lines. Asserted when the port B
CC2 pin is connected to the CC line in cable.
PB_POL
USB Port B Fault Indication. /PB_FAULT indicates overcurrent on PB_BUS or
overtemperature conditions. /PB_FAULT is an open drain in normal conditions. Pull /
PB_FAULT low during fault conditions.
PB_FAULT
FREQ/ SYNC
EN/UV
BOOT
18
19
20
21
22
23
A
A
A
P
P
P
Switching Frequency Program and External Clock Input. Connect a resistor from FREQ to
GND to set the switching frequency.
Enable pin. Precision enable controls the regulator switching action and type-C. Do not
float. High = on, Low = off. Can be tied to SENSE directly. Precision enable input allows
adjustable UVLO by external resistor divider if tie to IN pin.
Bootstrap capacitor connection. Internally, the BOOT is connected to the cathode of the
booststrap diode. Connect the 0.1-μF bootstrap capacitor from SW to BOOT.
Input power. Connected to external DC supply. Expected range of bypass capacitors is 1
μF to 10 μF, connect from IN to PGND. Withstand up to 36 V without damage but
operating is suspended if VIN is above the 26-V OVP threshold.
IN
Switching output of the regulator. Internally connected to source of the HS FET and drain
of the LS FET. Connect to output inductor.
SW
(1) A = Analog, P = Power, G = Ground.
表7-3. Pin Functions for TPS25852-Q1 RPQ Package
NAME
NO.
TYPE (1)
DESCRIPTION
Output Voltage Setting. Short to GND to set the 5.17-V output voltage. Float or pull up to
VSENSE to set 5.1-V output voltage. Tie to GND through a 40.2-KΩ resistor to set 5.3-V
output voltage. Tie to GND through a 80.6-KΩ resistor to set 5.4-V output voltage.
VSET
1
A
TS
2
3
A
P
Temperature Sense terminal. Connect the TS input to the NTC thermistor.
Input of internal bias supply. Must connect to the SENSE pin directly. Power the internal
circuit.
BIAS
USB Port A Fault Indication. /PA_FAULT indicates overcurrent on PA_BUS or
overtemperature conditions. /PA_FAULT is an open drain in normal conditions. Pull /
PA_FAULT low during fault conditions.
PA_FAULT
4
A
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
7
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
表7-3. Pin Functions for TPS25852-Q1 RPQ Package (continued)
NAME
NO.
TYPE (1)
DESCRIPTION
USB Port A Enable pin. To control the USB port A channel load switch ON/OFF. When
pull-low, the pin turns off the port A USB power and CC1/2 current and voltage. When pull-
high, the pin turns on the port A USB power and CC1/2 current and voltage. Can be tied to
SENSE directly to automatically turn on USB port.
PA_EN
5
A
AGND
PA_CC1
PA_CC2
6
7
8
P
A
A
Analog ground terminal. Connect AGND to PGND.
Connect to Type-C Port A CC1 pin. Analog input, output, or both.
Connect to Type-C Port A CC2 pin. Analog input, output, or both.
Current Limit program. Connect a resistor to set the current limit threshold. Short to GND
to set the default 3.55-A current limit.
ILIM
9
A
P
P
P
P
PA_BUS
SENSE
PB_BUS
OUT
10
11
12
13
Port A BUS output.
Output Voltage Sensing, external load on this pin is strictly prohibited. Connect to the other
side of the external inductor.
Port B BUS output,
Output pin. Provide 5.1-V voltage to power external load with max 200-mA capability. The
voltage follows the VSET setting.
PB_CC2
PB_CC1
14
15
A
A
Connect to Type-C Port B CC2 pin. Analog input, output, or both.
Connect to Type-C Port B CC1 pin. Analog input, output, or both.
Power Ground Terminal. Connected to the source of LS FET internally. Connect to system
ground, AGND, and the ground side of CIN and COUT capacitors. Path to CIN must be as
short as possible.
PGND
16,24,25
17
P
A
USB Port B Enable pin. To control the USB port B channel load switch ON/OFF. When
pull-low, the pin turns off the port B USB power and CC1/2 current and voltage. When pull-
high, the pin turns on the port B USB power and CC1/2 current and voltage. Can be tied to
SENSE directly to automatically turn on USB port.
PB_EN
USB Port B Fault Indication. /PB_FAULT indicates overcurrent on PB_BUS or
overtemperature conditions. /PB_FAULT is an open drain in normal conditions. Pull /
PB_FAULT low during fault conditions.
PB_FAULT
FREQ/ SYNC
EN/UV
BOOT
18
19
20
21
22
23
A
A
A
P
P
P
Switching Frequency Program and External Clock Input. Connect a resistor from FREQ to
GND to set the switching frequency.
Enable pin. Precision enable controls the regulator switching action and type-C. Do not
float. High = on, Low = off. Can be tied to SENSE directly. Precision enable input allows
adjustable UVLO by external resistor divider if tie to IN pin.
Bootstrap capacitor connection. Internally, the BOOT is connected to the cathode of the
booststrap diode. Connect the 0.1-μF bootstrap capacitor from SW to BOOT.
Input power. Connected to external DC supply. Expected range of bypass capacitors is 1
μF to 10 μF. Connect from IN to PGND. Withstand up to 36 V without damage but
operating is suspended if VIN is above the 26-V OVP threshold.
IN
Switching output of the regulator. Internally connected to source of the HS FET and drain
of the LS FET. Connect to output inductor.
SW
(1) A = Analog, P = Power, G = Ground.
Copyright © 2021 Texas Instruments Incorporated
8
Submit Document Feedback
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
8 Specifications
8.1 Absolute Maximum Ratings
Over the recommended operating junction temperature range of -40°C to +150°C and AGND = PGND (unless otherwise
noted)(1)
PARAMETER
IN to PGND
MIN
–0.3
–0.3
–0.3
–0.3
–0.3
–0.3
-0.3
MAX
40(2)
35
6
UNIT
IN to SW
BIAS, SENSE to PGND
EN to AGND
11
6
Input voltage
V
FREQ/SYNC to AGND
PA_EN, PB_EN to AGND
VSET, ILIM to AGND
AGND to PGND
6
6
0.3
35
35
6
–0.3
–0.3
–3.5
–0.3
–0.3
–0.3
–0.3
–0.3
–0.3
–0.3
SW to PGND
SW to PGND (less than 10 ns transients)
BOOT to SW
Output voltage
Voltage range
V
V
PA_BUS, PB_BUS, OUT to PGND
CC1, CC2 to AGND
DP, DM to AGND
6
6
6
PA_POL , PB_POL to AGND
PA_FAULT, PB_FAULT to AGND
TS to AGND
6
6
6
Pin positive sink current, ISNK CC1, CC2 (while applying VCONN)
1
A
I/O current
DP to DM in BC1.2 DCP Mode
Junction temperature
35
150
150
mA
°C
°C
–35
-40
TJ
Tstg
Storage temperature
–65
(1) Stresses beyond those listed under Absolute Maximum Rating may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under
Recommended Operating Condition. Exposure to absolute-maximum-rated conditions for extended periods may affect device
reliability.
(2) VIN rising slew rate below 20V/ms if in 0-V to 40-V transient, room temperature, maximum 500-uF cap at SENSE.
8.2 ESD Ratings
VALUE
±2000(2)
±750(3)
±750(3)
UNIT
Human body model (HBM), per AEC Q100-002(1)
V(ESD) Electrostatic discharge
Corner pins
V
Charged device model (CDM), per
AEC Q100-011
Other pins
(1) AEC Q100-002 indicates that HBM stressing shall be in accordance with the ANSI/ESDA/JEDEC JS-001 specification.
(2) The passing level per AEC-Q100 Classification H2.
(3) The passing level per AEC-Q100 Classification C5
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
9
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
8.3 Recommended Operating Conditions
Over the recommended operating junction temperature range of -40°C to 150°C. Voltages are with respect to GND (unless
otherwise noted)
MIN
NOM
MAX UNIT
IN to PGND
5.5
26
EN
0
VSENSE
VI
Input voltage
TS
0
VSENSE
VSENSE
3.3
PA_EN, PB_EN
0
V
FREQ/SYNC when driven by external clock
PA_FAULT, PB_FAULT, PA_POL, PB_POL
PA_BUS, PB_BUS, OUT
0
VPU
VO
Pull up voltage
Output voltage
0
5
VSENSE
5.5
PA_BUS, PB_BUS
0
3
A
A
OUT
0
0.2
IO
Output current
DP to DM Continuous current in BC1.2 DCP Mode
15
–15
CC1 or CC2 source current when supplying
VCONN
mA
ISRC
ISNK
Source current
Sink current
250
PA_FAULT, PB_FAULT, PA_POL, PB_POL
10
100
100
100
100
RVSET
0
0
0
0
kΩ
kΩ
kΩ
kΩ
uF
RILIM
REXT
External resistnace
External capacitance
RFREQ
RIMON
CEXT
TJ
CBOOT
0.1
Operating junction temperature
150
°C
–40
Copyright © 2021 Texas Instruments Incorporated
10
Submit Document Feedback
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
8.4 Thermal Information
TPS2585x-Q1
THERMAL METRIC(1) (2)
RPQ (VQFN)
25 PINS
37.7
UNIT
RθJA
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
RθJC(top)
RθJB
17.2
8.8
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
0.3
ΨJT
8.8
ΨJB
RθJC(bot)
20.3
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
(2) Power rating at a specific ambient temperature TA should be determined with a maximum junction temperature of 150 °C.
8.5 Electrical Characteristics
Limits apply over the recommended operating junction temperature (TJ) range of -40°C to +150°C; VIN = 13.5 V, fSW
=2.1MHz, VSET short to GND unless otherwise stated. Minimum and maximum limits are specified through test, design or
statistical correlation. Typical values represent the most likely parametric norm at TJ = 25°C, and are provided for reference
purposes only.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
SUPPLY VOLTAGE (IN PIN)
Shutdown quiescent current;
measured at IN pin.
ISD
IQ
34
63
200
uA
µA
VEN/UV = 0, -40C ≤TJ ≤85C
Operating quiescent current (DCDC
disable)
VEN=VSENSE, CCx=open, -40C ≤TJ
≤85C
Voltage on VIN pin when buck
regulator stops switching
VOVLO_R
26.6
1.26
27.5
0.5
28.4
V
V
VOVLO_HYS
Hysteresis
ENABLE AND UVLO (EN/UVLO PIN)
Rising threshold for not in External
UVLO
VEN/UVLO_R
VEN/UV rising threshold
VEN/UVLO falling
1.3
1.34
1.98
V
VEN/UVLO_HYS
Hysteresis
100
mV
PA_EN, PB_EN input level required to
turn on PA_BUS and PB_BUS Load
Switch (TPS25852-Q1)
VPA/B_EN_H
VPA_EN or VPB_EN rising threshold
1.6
V
PA_EN, PB_EN input level required to
turn off PA_BUS and PB_BUS Load
Switch (TPS25852-Q1)
VPA/B_EN_L
VPA_EN or VPB_EN falling threshold
VPA_EN or VPB_EN falling threshold
0.97
1.5
V
VEN1/2_HYS
BOOTSTRAP
VBTST_UVLO
RBOOT
Hysteresis(TPS25852-Q1)
100
mV
Bootstrap voltage UVLO threshold
Bootstrap pull-up resistence
2.2
7.7
V
VSENSE-BOOT=0.1V
Ω
BUCK REGULATOR
IL-SC-HS
IL-SC-LS
IL-NEG-LS
IZC
High-side current limit
BOOT-SW=5V
SENSE=5V
SENSE=5V
10.2
8.5
-7
11.4
10
12.6
11.5
-3
A
A
A
A
Low-side current limit
Low-side negative current limit
Zero current detector threshold
-5
0.01
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
11
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
8.5 Electrical Characteristics (continued)
Limits apply over the recommended operating junction temperature (TJ) range of -40°C to +150°C; VIN = 13.5 V, fSW
=2.1MHz, VSET short to GND unless otherwise stated. Minimum and maximum limits are specified through test, design or
statistical correlation. Typical values represent the most likely parametric norm at TJ = 25°C, and are provided for reference
purposes only.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
CC1 or CC2 pulldown resistance = Rd,
VSET float or pull up to VSENSE
,
-1%
5.1
+1%
V
TJ =25℃
CC1 or CC2 pulldown resistance = Rd,
VSET short to AGND, TJ =25℃
-1%
-1%
-1%
5.17
5.3
+1%
+1%
+1%
2
V
V
VSENSE
BUCK Output voltage
CC1 or CC2 pulldown resistance = Rd,
RVSET =40.2KΩ, TJ =25℃
CC1 or CC2 pulldown resistance = Rd,
RVSET =80.6KΩ, TJ =25℃
5.4
V
CC1 or CC2 pulldown resistance = Rd,
-40℃≤TJ ≤150℃
VSENSE
BUCK Output voltage accuracy
%
–2
SENSE input level to enable DCDC
switching
VSENSE rising, CC1 or CC2 pull down
resistance = Rd
VDCDC_UVLO_R
VDCDC_UVLO_HYS
VDROP
3.85
4
0.4
300
18
4.15
V
VSENSE falling, CC1 or CC2 pull down
resistance = Rd
Hysteresis
V
VIN = VSENSE + VDROP, VSENS = 5.1V,
IPA_BUS=3A, IPB_BUS=3A
Dropout voltage ( VIN-VSENSE
)
mV
mΩ
mΩ
IPA_BUS=3A, IPB_BUS=3A, BOOT-
SW=5V, -40℃≤TJ ≤150℃
RDS-ON-HS
RDS-ON-LS
High-side MOSFET ON-resistance
Low-side MOSFET ON-resistance
34
IPA_BUS=3A, IPB_BUS=3A, VSENSE=5V,
-40℃≤TJ ≤150℃
9.5
18.5
POWER SWITCH AND CURRENT LIMIT
USB Load Switch MOSFET ON-
IPA_BUS=3A, IPB_BUS=3A;
-40℃≤TJ≤150℃
RDS-ON_USB
6.8
11.73
mΩ
mΩ
resistance
OUT Load Switch MOSFET ON-
resistance
RDS-ON_OUT
IOUT = 0.3 A
230
RDS-ON_VCONN
RDS-ON_VCONN
On-state resistance
On-state resistance
TJ = 25°C, ICCn = 0.25 A
410
410
550
740
mΩ
mΩ
–40°C ≤TJ ≤150°C, ICCn = 0.25 A
Voltage on SENSE pin that will enable
the USB Load Switch
VUSBLS_UVLO_R
3.95
4.1
200
500
4.25
V
VUSBLS_UVLO_HYS Hysteresis
mV
Ω
Discharge resistance for Port A or Port Apply 5V on PA_BUS or PB_BUS,
B BUS
RBUS_DCHG
250
670
750
730
CC1 or CC2= Rd
Rising threshold voltage for BUS not
discharged
VTH_R_BUS_DCHGb
700
100
150
mV
mV
KΩ
VTH_HYS_BUS_DCHG Hysteresis
VPx_BUS =4V, No sink termination on
CC lines, Time>tW_BUS_DCHG
VBUS_DCHG_BLEED BUS bleed resistance
100
200
849
2434
3018
3748
4040
4876
4828
4265
1061
2704
3354
4165
4490
5418
5680
4490
1273
2974
3689
4581
4938
5960
6532
4714
mA
mA
mA
mA
mA
mA
mA
mA
RILIM=48.7KΩ
RILIM=19.1KΩ
RILIM=15.4KΩ
RILIM=12.4KΩ
BUS output short-circuit secondary
current limit
IOS_HI
RILIM=11.5KΩ
RILIM=9.53KΩ
RILIM=0Ω(short to GND)
RILIM=11.5KΩ, TJ =25℃
Copyright © 2021 Texas Instruments Incorporated
12
Submit Document Feedback
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
8.5 Electrical Characteristics (continued)
Limits apply over the recommended operating junction temperature (TJ) range of -40°C to +150°C; VIN = 13.5 V, fSW
=2.1MHz, VSET short to GND unless otherwise stated. Minimum and maximum limits are specified through test, design or
statistical correlation. Typical values represent the most likely parametric norm at TJ = 25°C, and are provided for reference
purposes only.
PARAMETER
TEST CONDITIONS
MIN
530.4
1521
TYP
MAX UNIT
663
800
mA
mA
mA
mA
mA
mA
mA
mA
mA
RILIM=48.7KΩ
1690
1859
RILIM=19.1KΩ
1886.4
2342.7
2525.4
3047.4
3017.5
2666
2096 2305.6
2603 2863.3
2806 3086.6
3386 3724.6
3550 4082.5
RILIM=15.4KΩ
RILIM=12.4KΩ
IOS_BUS
BUS output short-circuit current limit
OUT output short-circuit current limit
RILIM=11.5KΩ
RILIM=9.53KΩ
RILIM=0Ω(short to GND)
RILIM=11.5KΩ, TJ =25℃
Short circuit current limit
2806
450
2946
495
IOS_OUT
390
VCONN output short-circuit current
limit
IOS_VCONN
Short circuit current limit
240
70
300
360
mA
CABLE COMPENSATION VOLTAGE
Cable compensation
VDROP_COM
IPA_BUS or IPB_BUS=2.4A,
VSET=GND(set 5.17V output)
90
110
mV
voltage(TPS25850/1/2)
CC CONNECT MANAGEMENT
ISRC_CC_3A
Sourcing current
304
167
330
180
356
194
µA
µA
CC pin voltage: 0 V ≤VCCn ≤2.45 V
Sourcing current in thermal
management(Temp warm)
CC pin voltage: 0 V ≤VCCn ≤1.5 V ,
TA> 85℃
ISRC_CC_1.5A
Sourcing current in thermal
management(Temp hot)
CC pin voltage: 0 V ≤VCCn ≤1.5 V ,
TA> 85℃
ISRC_CC_DFLT
64
80
105
10
µA
µA
CCx is the CC pin under test, CCy is
the other CC pin. CC pin voltage
VCCx = 5.5 V, CCy floating, VEN_UV
0 V or VSENSE, 0 V ≤VIN ≤26 V
IREV is current into CCx pin
=
IREV
Reverse leakage current
2.75
Rising threshold voltage for VCONN
not discharged
CC pin that was providing VCONN in
previous SINK state
VTH_R
670
700
100
730
mV
mV
VTH_HYS
Hysteresis
FAULT, POL(TPS25851/2-Q1)
PA_FAULT, PB_FAULT Output low
voltage (TPS25851/2-Q1)
VOL
IOFF
VOL
IOFF
ISNK_PIN = 1 mA
VPIN = 5.5 V
250
2.2
250
1.8
mV
µA
PA_FAULT, PB_FAULT Off-state
leakage (TPS25851/2-Q1)
PA_POL, PB_POL Output low voltage
(TPS25851-Q1)
ISNK_PIN = 1 mA
VPIN = 5.5 V
mV
µA
PA_POL, PB_POL Off-state
leakage (TPS25851-Q1)
BC 1.2 DOWNSTREAM CHARGING PORT (TPS25850-Q1)
RDPM_SHORT DP and DM shorting resistance
DIVIDER 3 MODE (TPS25850-Q1)
70
200
Ω
VDP_DIV3
VDM_DIV3
RDP_DIV3
RDM_DIV3
DP output voltage
2.57
2.57
24
2.7
2.7
30
2.84
2.84
36
V
V
DM output voltage
DP output impedance
DM output impedance
IDP_IN = –5 µA
IDM_IN = –5 µA
kΩ
kΩ
24
30
36
1.2-V MODE (TPS25850-Q1)
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
13
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
8.5 Electrical Characteristics (continued)
Limits apply over the recommended operating junction temperature (TJ) range of -40°C to +150°C; VIN = 13.5 V, fSW
=2.1MHz, VSET short to GND unless otherwise stated. Minimum and maximum limits are specified through test, design or
statistical correlation. Typical values represent the most likely parametric norm at TJ = 25°C, and are provided for reference
purposes only.
PARAMETER
TEST CONDITIONS
MIN
1.12
1.12
84
TYP
MAX UNIT
VDP_1.2V
VDM_1.2V
RDP_1.2V
RDM_1.2V
DP output voltage
DM output voltage
DP output impedance
DM output impedance
1.2
1.26
1.26
126
126
V
V
1.2
100
100
IDP_IN = –5 µA
kΩ
kΩ
84
IDM_IN = –5 µA
FREQ/SYNC THRESHOLD
FREQ/SYNC high threshold for
Amplitude of SYNC clock AC signal
(measured at FREQ/SYNC pin)
VIH_FREQ/SYNC
2
V
V
external clock synchronization
FREQ/SYNC low threshold for
external clock synchronization
Amplitude of SYNC clock AC signal
(measured at FREQ/SYNC pin)
VIL_FREQ/SYNC
0.8
0.525
0.683
TEMPERATURE SENSING
VWARN_HIGH Temperature warning threshold rising As percentage to VSENSE
VWARN_HYS
0.475
0.618
0.5
0.1
V/V
V/V
Hysteresis
As percentage to VSENSE
Temperature Hot assert threshold
rising to reduce SENS voltage
VHOT_HIGH
VHOT_HYS
VR_VSENS
As percentage to VSENSE
0.65
0.1
V/V
V/V
V
Hysteresis
As percentage to VSENSE
VSENSE voltage decay when
Temperature Hot assert
TS pin voltage rise above 0.65*VSENSE
4.77
THERMAL SHUTDOWN
TLS_SD USB Load Switch Over Temperature
Shutdown threshold
Recovery threshold
Shutdown threshold
Recovery threshold
160
150
166
154
°C
°C
°C
°C
TSD
Thermal shutdown
8.6 Timing Requirements
Over the recommended operating junction temperature range of -40 °C to 150 °C (unless otherwise noted)
MIN NOM MAX UNIT
POL(TPS25851-Q1)
tDEGLA_POL Asserting deglitch time
tDEGLD_POL De-asserting deglitch time
100
8.2
150
200 ms
18 ms
12.5
FAULT (TPS25851/2-Q1)
(Thermal SD Fault assertion is
instantaneous, not subject to this timing)
tDEGLA_FAULT Asserting deglitch time
2.94
4.1 5.42 ms
tDEGLD_FAULT De-asserting deglitch time
11.09 16.38 23.03 ms
BUS DISCHARGE
tDEGA_BUS_DC
Discharge asserting deglitch
5.6
12.3 21.2 ms
260 360 ms
HG
VBUS discharge time after sink termination
removed from CC lines
VBUS = 1 V, time ISNK_OUT > 1 mA after sink
termination removed from CC lines
tW_BUS_DCHG
170
POWER SWITCH TIMING
Deglitch time for USB power switch current
limit enable
tIOS_HI_DEG
tIOS_HI_RST
tr_USB
USB port enter overcurrent (per ILIM setting) 1.228 2.048 2.867 ms
9.6 16 22.4 ms
1.67 ms
MFI OCP reset timing
CL = 1 µF, RL = 100 Ω(measured from 10%
to 90% of final value)
PA_BUS, PB_BUS, BUS voltage rise time
Copyright © 2021 Texas Instruments Incorporated
14
Submit Document Feedback
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
8.6 Timing Requirements (continued)
Over the recommended operating junction temperature range of -40 °C to 150 °C (unless otherwise noted)
MIN NOM MAX UNIT
CL = 1 µF, RL = 100 Ω(measured from 90%
to 10% of final value)
tf_USB
PA_BUS, PB_BUS, BUS voltage fall time
0.49
ms
ton_USB
toff_USB
PA_BUS, PB_BUS, BUS voltage turnon-time
PA_BUS, PB_BUS, BUS voltage turnoff-time
2.59
2.07
ms
ms
CL = 1 µF, RL = 100 Ω
CL = 1 µF, RL = 100 Ω
PA_BUS, PB_BUS, BUS short-circuit
response time
tIOS_USB
tr_OUT
1
us
CL = 1 µF, RL = 1 Ω
CL = 1 µF, RL = 100 Ω(measured from 10%
to 90% of final value)
OUT voltage rise time
OUT voltage fall time
0.12
0.16
0.2 0.28 ms
0.22 0.28 ms
CL = 1 µF, RL = 100 Ω(measured from 90%
to 10% of final value)
tf_OUT
ton_OUT
OUT voltage turnon-time
0.6
1.1 1.65 ms
0.54 0.62 ms
CL = 1 µF, RL = 100 Ω
CL = 1 µF, RL = 100 Ω
CL = 1 µF, RL = 1 Ω
CL = 1 µF, RL = 1 Ω
toff_OUT
OUT voltage turnoff-time
0.45
tIOS_OUT
tIOS_VCONN
OUT short-circuit response time
CC-VCONN short circuit response time
1.4
1
4
us
3.5 µs
CL = 1 µF, RL = 100 Ω(measured from 10%
to 90% of final value); 5.1KΩ on CC1 and
1KΩ on CC2
tr_VCONN
VCONN output voltage rise time
VCONN output voltage fall time
0.2
0.28 0.36 ms
0.23 0.28 ms
CL = 1 µF, RL = 100 Ω(measured from 90%
to 10% of final value); 5.1KΩ on CC1 and
1KΩ on CC2
tf_VCONN
0.18
CL = 1 µF, RL = 100 Ω; 5.1KΩ on CC1 and
1KΩ on CC2
ton_VCONN
VCONN output voltage turnon time
VCONN output voltage turnoff time
0.7
1.2
1.7 ms
CL = 1 µF, RL = 100 Ω; 5.1KΩ on CC1 and
1KΩ on CC2
toff_VCONN
0.37
0.44 0.51 ms
HICCUP MODE
THICP_ON
OUT, PA_BUS, PB_BUS output hiccup mode
ON time
OC, VOUT, VPA_BUS, VPB_BUS drop 10%
2.94
367
4.1 5.42 ms
OUT, PA_BUS, PB_BUS output hiccup mode OC, OUT, PA_BUS, PB_BUS connect to
OFF time GND
THICP_OFF
524
715 ms
8.7 Switching Characteristics
Over the recommended operating junction temperature range of -40 °C to 150 °C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
SW (SW PIN)
TON_MIN
Minimum turnon-time
84
6
ns
µs
Maximum turnon-time, HS timeout in
dropout
TON_MAX
TOFF_MIN
Dmax
Minimum turnoff time
81
98
ns
%
Maximum switch duty cycle
TIMING RESISTOR AND INTERNAL CLOCK
Switching frequency range using
FREQ mode
fSW_RANGE
200
3000
kHz
9 kΩ≤RFREQ≤99 kΩ
228
360
253
400
278
440
kHz
kHz
kHz
RFREQ = 80.6 kΩ
RFREQ = 49.9 kΩ
RFREQ = 8.45 kΩ
fSW
Switching frequency
1980
2200
2420
Frequency span of spread spectrum
operation
FSSS
±6
%
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
15
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
MAX UNIT
8.7 Switching Characteristics (continued)
Over the recommended operating junction temperature range of -40 °C to 150 °C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
EXTERNAL CLOCK(SYNC)
Switching frequency using external
clock on FREQ/SYNC pin
fFREQ/SYNC
200
3000
kHz
ns
fSYNC = 400kHz, VFREQ/SYNC
VIH_FREQ/SYNC, VFREQ/SYNC < VIL_FREQ/
>
TSYNC_MIN
Minimum SYNC input pulse width
PLL lock time
100
SYNC
TLOCK_IN
100
µs
Attach asserting deglitch in the
Detached Mode
tDEGA_CC_ATT_DETM
1.29
8.2
2.05
3.05
18
ms
tDEGA_CC_DETACH_S Detach asserting deglitch for exiting
12.5
ms
SINK Mode
INKM
tDEGA_CC_SHORT
tDEGA_CC_LONG
Detach, Rd and Ra asserting deglitch
Long deglitch
92
192
148
339
200
µs
103
ms
Copyright © 2021 Texas Instruments Incorporated
16
Submit Document Feedback
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
8.8 Typical Characteristics
Unless otherwise specified the following conditions apply: VIN = 13.5 V, fSW = 2.1 MHz, L = 0.68 µH, CSENSE = 66 µF, CPA_BUS
= 1 µF, CPB_BUS = 1 µF, TA = 25 °C.
70
60
50
40
30
20
200
180
160
140
120
100
-40C
25C
150C
-40C
25C
150C
4
8
12
16 20
Input Voltage (V)
24
28
32
4
8
12
16 20
Input Voltage (V)
24
28
32
VEN/EULVO = 0 V
PA_CC1 = Rd
PB_CC1 = Rd
VEN/UVLO = VSENSE PA_CC1/2 = OPEN PB_CC1/2 = OPEN
图8-1. Shutdown Quiescent Current
图8-2. Standby Quiescent Current
1.68
1.36
1.34
1.32
1.3
Vin = 5.5V
Vin = 13.5V
Vin = 26V
Vin = 5.5V
Vin = 13.5V
Vin = 26V
1.67
1.66
1.65
1.64
1.63
1.62
1.61
1.6
1.59
1.58
1.57
1.28
1.26
-40 -20
0
20
40
Temperature (C)
60
80 100 120 140 160
-50
-25
0
25
50
75
Temperature (C)
100
125
150
图8-4. Precision USB PA/PB Enable Threshold
图8-3. Precision Device Enable Threshold
5.2
5.46
Vin = 5.5V
Vin = 13.5V
Vin = 26V
Vin = 5.5V
Vin = 13.5V
Vin = 26V
5.19
5.18
5.17
5.16
5.15
5.14
5.44
5.42
5.4
5.38
5.36
5.34
-50
-25
0
25
Temperature (C)
50
75
100
125
150
-50
-25
0
25
Temperature (C)
50
75
100
125
150
VSET = GND
RVSET = 80.6 kΩ
图8-5. VSENSE Voltage vs Junction Temperature
图8-6. VSENSE Voltage vs Junction Temperature
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
17
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
8.8 Typical Characteristics (continued)
Unless otherwise specified the following conditions apply: VIN = 13.5 V, fSW = 2.1 MHz, L = 0.68 µH, CSENSE = 66 µF, CPA_BUS
= 1 µF, CPB_BUS = 1 µF, TA = 25 °C.
3.94
3.96
3.98
4
11.7
11.6
11.5
11.4
11.3
11.2
Vin = 5.5V
Vin = 13.5V
Vin = 26V
-40C
25C
150C
4.02
4.04
4.06
-50
-25
0
25
Temperature (C)
50
75
100
125
150
4
8
12
16
Input Voltage (V)
20
24
28
图8-8. High-side Current Limit vs Input Voltage
VEN/EULVO = VSENSE
PA_CC1= Rd
PB_CC1= Rd
图8-7. DCDC UVLO Threshold
10.3
10.2
10.1
10
40
-40C
25C
150C
Vin = 5.5V
Vin = 13.5V
Vin = 26V
35
30
25
20
15
9.9
9.8
4
8
12
16
Input Voltage (V)
20
24
28
-50
-25
0
25
50
75
Temperature (C)
100
125
150
图8-9. Low-side Current Limit vs Input Voltage
IPA_BUS = 3 A
IPB_BUS = 3 A
图8-10. High-side MOSFET on Resistance vs Junction
Temperature
18
16
14
12
3640
Vin = 5.5V
Vin = 13.5V
Vin = 26V
3600
3560
3520
3480
3440
3400
10
Vin = 5.5V
Vin = 13.5V
Vin = 26V
8
-50
-25
0
25
Temperature (C)
50
75
100
125
150
-50
-25
0
25
Temperature (C)
50
75
100
125
150
IPA_BUS = 3 A
IPB_BUS = 3 A
ILIM = GND
图8-11. Low-side MOSFET on Resistance vs Junction
图8-12. USB Power Switch Current Limit vs Junction
Temperature
Temperature
Copyright © 2021 Texas Instruments Incorporated
18
Submit Document Feedback
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
8.8 Typical Characteristics (continued)
Unless otherwise specified the following conditions apply: VIN = 13.5 V, fSW = 2.1 MHz, L = 0.68 µH, CSENSE = 66 µF, CPA_BUS
= 1 µF, CPB_BUS = 1 µF, TA = 25 °C.
3520
3480
3440
3400
3360
3320
3280
2200
2160
2120
2080
2040
2000
1960
Vin = 5.5V
Vin = 13.5V
Vin = 26V
Vin = 5.5V
Vin = 13.5V
Vin = 26V
-50
-25
0
25
Temperature (C)
50
75
100
125
150
-50
-25
0
25
Temperature (C)
50
75
100
125
150
RILIM = 9.53 kΩ
RILIM = 15.4 kΩ
图8-13. USB Power Switch Current Limit vs Junction
图8-14. USB Power Switch Current Limit vs Junction
Temperature
Temperature
520
328
Vin = 5.5V
Vin = 13.5V
Vin = 26V
Vin = 5.5V
Vin = 13.5V
Vin = 26V
500
480
460
440
420
400
320
312
304
296
288
280
-50
-25
0
25
Temperature (C)
50
75
100
125
150
-50
-25
0
25
Temperature (C)
50
75
100
125
150
图8-15. OUT Power Switch Current Limit vs Junction
图8-16. VCONN Power Switch Current Limit vs Junction
Temperature
Temperature
100
96
92
88
84
80
9.6
8.8
8
7.2
6.4
Vin = 5.5V
Vin = 13.5V
Vin = 26V
5.6
4.8
-50
-25
0
25
Temperature (C)
50
75
100
125
150
-50
-25
0
25
Temperature (C)
50
75
100
125
150
图8-18. USB Power Switch On Resistance vs Junction
IPA/B_BUS = 2.4 A
VSET = GND
Temperature
图8-17. Cable Compensation Voltage vs Junction Temperature
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
19
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
8.8 Typical Characteristics (continued)
Unless otherwise specified the following conditions apply: VIN = 13.5 V, fSW = 2.1 MHz, L = 0.68 µH, CSENSE = 66 µF, CPA_BUS
= 1 µF, CPB_BUS = 1 µF, TA = 25 °C.
400
360
320
280
240
200
160
600
550
500
450
400
350
300
Vin = 5.5V
Vin = 13.5V
Vin = 26V
Vin = 5.5V
Vin = 13.5V
Vin = 26V
-50
-25
0
25
Temperature (C)
50
75
100
125
150
-50
-25
0
25
Temperature (C)
50
75
100
125
150
图8-19. OUT Power Switch On Resistance vs Junction
图8-20. VCONN Power Switch On Resistance vs Junction
Temperature
Temperature
424
2280
Vin = 5.5V
Vin = 13.5V
Vin = 26V
Vin = 5.5V
Vin = 13.5V
Vin = 26V
416
408
400
392
384
376
2240
2200
2160
2120
2080
2040
-50
-25
0
25
Temperature (C)
50
75
100
125
150
-50
-25
0
25
Temperature (C)
50
75
100
125
150
RFREQ = 49.9 kΩ
RFREQ = 8.45 kΩ
图8-21. Switching Frequency vs Junction Temperature
图8-22. Switching Frequency vs Junction Temperature
450
0.56
UFP 1.5A
UFP 3A
400
0.54
0.52
0.5
350
300
250
200
150
0.48
0.46
0.44
-50
-25
0
25
Temperature (C)
50
75
100
125
150
-50
-25
0
25
Temperature (C)
50
75
100
125
150
图8-23. CC Sourcing Current vs Junction Temperature
图8-24. TS Temperature Wam Threshold vs Junction
Temperature
Copyright © 2021 Texas Instruments Incorporated
20
Submit Document Feedback
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
8.8 Typical Characteristics (continued)
Unless otherwise specified the following conditions apply: VIN = 13.5 V, fSW = 2.1 MHz, L = 0.68 µH, CSENSE = 66 µF, CPA_BUS
= 1 µF, CPB_BUS = 1 µF, TA = 25 °C.
0.72
4.82
0.7
4.8
0.68
0.66
0.64
0.62
0.6
4.78
4.76
4.74
4.72
4.7
-50
-25
0
25
Temperature (C)
50
75
100
125
150
-50
-25
0
25
Temperature (C)
50
75
100
125
150
图8-25. TS Temperature Hot Threshold vs Junction
图8-26. SENSE Voltage in Temperature Hot vs Junction
Temperature
Temperature
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
21
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
9 Parameter Measurement Information
OUT
90%
R(L)
tr
C(L)
tf
V(OUT)
10%
图9-1. OUT Rise-Fall Test Load Figure
图9-2. Power-On and Power-Off Timing
V(EN)
50%
50%
5 V
ton
toff
t(DCHG)
V(OUT)
90%
V(OUT)
0 V
10%
图9-3. OUT Discharge During Mode Change
图9-4. Enable Timing, Active-High Enable
IOS
I(OUT)
t(IOS)
图9-5. Output Short-Circuit Parameters
Copyright © 2021 Texas Instruments Incorporated
22
Submit Document Feedback
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
10 Detailed Description
10.1 Overview
The TPS2585x-Q1 is a full-featured solution for implementing a compact USB charging port with support for both
Type-C and BC1.2 standards. The device contain an efficient buck regulator power source. For dual Type-C
ports, the TPS2585x-Q1 is capable of providing up to 6.6 A of output current at 5.17 V (nominal), 3 A for each
Type-C port, 200 mA for the OUT pin, and 200 mA for each VCONN power. The TPS2585x-Q1 is an automotive-
focused USB charging controller and offers a robust solution, so TI recommends to add adequate protection
(TVS3300 equivalent or better but auto qualified) on the IN pin to protect systems from high-power transients or
lightning strikes.
System designers can optimize efficiency or solution size through careful selection of switching frequency in the
range of 200 KHz–2400 KHz with sufficient margin to operate above or below the AM radio frequency band. For
switching frequency higher than 2400 KHz, the power dissipation significantly increases, so in a high ambient
temperature application, the 6.6-A output current capability is not ensured. The TPS2585x-Q1 buck regulator
operates in forced PWM mode, ensuring fixed switching frequency regardless of load current. Spread-spectrum
frequency dithering reduces harmonic peaks of the switching frequency, potentially simplifying EMI filter design
and easing compliance.
Current sensing through a precision FET current sense amplifier on the USB port enables an accurate, user-
programmable overcurrent limit setting, and linear cable compensation to overcome IR losses when powering
remote USB ports.
The TPS2585x-Q1 includes a TS input for user-programmable thermal protection using a negative temperature
coefficient (NTC) resistor.
The device can support the USB Type-C protocol. The TPS25850-Q1 also supports the legacy Battery Charging
Specification Rev 1.2 (BC1.2) DCP mode with an auto-detect feature to charge not only BC1.2-compliant
handheld devices, but also popular phones and tablets that incorporate their own propriety charging algorithm.
The TPS25851-Q1 supports USB cable polarity detection and fault condition detect for each port. The
TPS25852-Q1 can enable each port individually and can report fault condition for each port.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
23
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
10.2 Functional Block Diagram
Copyright © 2021 Texas Instruments Incorporated
24
Submit Document Feedback
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
10.3 Feature Description
10.3.1 Power-Down or Undervoltage Lockout
The device is in low power mode if the IN terminal voltage is less than VUVLO, so the part is considered dead
and all the terminals are high impedance. Once the IN voltage rises above the VUVLO threshold, the IC enters
sleep mode or active mode, depending on the EN/UVLO voltage.
The voltage on the EN/UVLO pin controls the ON/OFF operation of the TPS2585x-Q1. An EN/UVLO pin voltage
higher than VEN/UVLO-H is required to start the internal regulator and begin monitoring the CCn lines for a valid
Type-C connection. The internal USB monitoring circuitry is on when VIN is within the operation range and the
EN/UVLO threshold is cleared. For TPS25850-Q1, the buck regulator and the USB ports load switch remains
OFF until a valid Type-C detection has been made. For TPS25851-Q1 and TPS25852-Q1, the buck regulator
starts to operate, however, the USB ports load switch remains OFF until a valid Type-C detection has been
made. This feature ensures the cold socket (0 V) USB Type-C VBUS requirement is met.
The EN/UVLO pin is an input and cannot be left open or floating. The simplest way to enable the operation of the
TPS2585x-Q1 is to connect EN to SENSE. This connection allows self-startup of the TPS2585x-Q1 when VIN is
within the operation range. Note that you cannot connect the EN to IN pin directly for self-startup.
Many applications benefit from the employment of enable dividers RENT and RENB to establish a precision
system UVLO level for the TPS2585x-Q1 shown in 图 10-1. The system UVLO can be used for sequencing,
ensuring reliable operation, or supply protection, such as a battery discharge level. To ensure the USB port VBUS
is within the 5-V operating range as required for USB compliance (for the latest USB specifications and
requirements, refer to USB.org), TI suggests that the RENT and RENB resistors be chosen such that the
TPS2585x-Q1 enables when VIN is approximately 6 V. Considering the dropout voltage of the buck regulator and
IR losses in the system, 6 V provides adequate margin to maintain VBUS within USB specifications. If system
requirements, such as a warm crank (start) automotive scenario, require operation with VIN < 6 V, the values of
RENT and RENB can be calculated assuming a lower VIN. An external logic signal can also be used to drive the
EN/UVLO input when a microcontroller is present and it is desirable to enable or disable the USB port remotely
for other reasons.
IN
RENT
EN
RENB
图10-1. System UVLO by Enable Divider
UVLO configuration using external resistors is governed by the following equations:
VIN ON
≈
’
÷
◊
(
)
RENT
=
- 1 ì R
∆
÷
ENB
∆
VEN/UVLO _H
«
(1)
(2)
≈
’
VEN/UVLO _HYS
VIN OFF = VIN ON ì 1 -
∆
÷
÷
(
)
(
)
∆
VEN/UVLO _H
«
◊
For example:
VIN(ON) = 6 V
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
25
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
RENT = 20 kΩ
RENB = [(VEN-VOUT-H) / (VIN(ON) –VEN)] × RENT
(3)
RENB = 5 kΩ
Therefore, VIN(OFF) = 5.5 V
10.3.2 Input Overvoltage Protection (OVP) - Continuously Monitored
The operation voltage range of the TPS2585x-Q1 is up to 26 V. If the input source applies an overvoltage, the
buck regulator HSFET/LSFET turns off immediately. Thus, the USB ports and OUT pin loses their power as well.
Once the overvoltage returns to a normal voltage, the buck regulator continues switching and provides power on
the USB ports and OUT pin.
During the overvoltage condition, the internal regulator regulates the SENSE voltage at 5 V, so the SENSE
always has power for the internal bias circuit and external NTC pullup reference.
10.3.3 Buck Converter
The following operating description of the TPS2585x-Q1 refers to the Functional Block Diagram. The TPS2585x-
Q1 integrates a monolithic, synchronous, rectified, step-down, switch-mode converter with internal power
MOSFETs and USB current-limit switches with charging ports auto-detection. The TPS2585x-Q1 offers a
compact solution that achieves up to 6.6 A of continuous output current with excellent load and line regulation
over a wide input supply range. The TPS2585x-Q1 supplies a regulated output voltage by turning on the high-
side (HS) and low-side (LS) NMOS switches with controlled duty cycle. During high-side switch ON time, the SW
pin voltage swings up to approximately VIN. The inductor current iL increases with linear slope (VIN – VOUT ) / L.
When the HS switch is turned off by the control logic, the LS switch is turned on after an anti-shoot-through dead
time. Inductor current discharges through the LS switch with a slope of –VOUT / L. The control parameter of a
buck converter is defined as Duty Cycle D = tON / TSW, where tON is the high-side switch ON time and TSW is the
switching period, shown in 图 10-2. The regulator control loop maintains a constant output voltage by adjusting
the duty cycle D. In an ideal buck converter, where losses are ignored, D is proportional to the output voltage
and inversely proportional to the input voltage: D = VOUT / VIN.
VSW
D = tON/ TSW
VIN
tON
tOFF
t
0
-VD
TSW
iL
ILPK
IOUT
DiL
t
0
图10-2. SW Node and Inductor Current Waveforms in Continuous Conduction Mode (CCM)
The TPS2585x-Q1 operates in a fixed-frequency, peak-current-mode control to regulate the output voltage. A
voltage feedback loop is used to get accurate DC voltage regulation by adjusting the peak current command
based on voltage offset. The peak inductor current is sensed from the high-side switch and compared to the
peak current threshold to control the ON time of the high-side switch. The voltage feedback loop is internally
compensated, which allows for fewer external components, making it easy to design, and provides stable
operation with a reasonable combination of output capacitors. The TPS2585x-Q1 operates in FPWM mode for
low output voltage ripple, tight output voltage regulation, and constant switching frequency.
Copyright © 2021 Texas Instruments Incorporated
26
Submit Document Feedback
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
10.3.4 FREQ/SYNC
The switching frequency of the TPS2585x-Q1 can be programmed by the resistor RFREQ from the FREQ/SYNC
pin and AGND pin. To determine the FREQ resistance, for a given switching frequency, use 方程式4:
-1.0483
RFREQ kW = 26660ì ƒ
kHz
SW
(4)
70
65
60
55
50
45
40
35
30
25
20
15
10
5
200 400 600 800 1000 1200 1400 1600 1800 2000 2200
Switching Frequency (kHz)
D024
图10-3. FREQ Set Resistor vs Switching Frequency
The normal method of setting the buck regulator switching frequency is by selecting an appropriate value FREQ
resistor, the typical FREQ resistors value are listed in 表10-1.
表10-1. Setting the Switching Frequency with FREQ
SWITCHING FREQUENCY (KHz)
FREQ (KΩ)
80.6
253
400
49.9
19.1
1000
2100
2200
8.87
8.45
The FREQ/SYNC pin can be used to synchronize the internal oscillator to an external clock. The internal
oscillator can be synchronized by AC coupling a positive edge into the FREQ/SYNC pin. When using a low
impedance signal source, the frequency setting resistor FREQ is connected in parallel with an AC coupling
capacitor, CCOUP, to a termination resistor, RTERM (for example, 50 Ω). The two resistors in series provide the
default frequency setting resistance when the signal source is turned off. A 10-pF ceramic capacitor can be used
for CCOUP. The AC coupled peak-to-peak voltage at the FREQ/SYNC pin must exceed the SYNC amplitude
threshold of 1.2 V (typ.) to trip the internal synchronization pulse detector, and the minimum SYNC clock HIGH
and LOW time must be longer than 100 ns (typ). A 2.5-V or higher amplitude pulse signal coupled through a 1-
nF capacitor, CSYNC, is a good starting point. 图 10-4 shows the device synchronized to an external system
clock. The external clock must be off before start-up to allow proper start-up sequencing.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
27
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
CCOUP
RT
PLL
PLL
Lo-Z
Hi-Z
Clock
Source
FREQ/
FREQ/
SYNC
Clock
RTERM
RT
SYNC
Source
图10-4. Synchronize to External Clock
The TPS2585x-Q1 switching action can be synchronized to an external clock from 200 KHz to 3 MHz. Even the
switching frequency can be set to higher than 2.4 MHz, but TI recommends to set the switching frequency below
2.4 MHz due to the power dissipation, the higher switching frequency results in more power loss on IC, cause
the junction temperature and also the board temperature rising, then the device can enter load shedding under
high ambient temperature.
图 10-5, 图 10-6 and 图 10-7 show the device switching frequency and behavior under different VIN voltage and
R
FREQ = 8.45 kΩ.
图10-8, 图10-9 and 图10-10 show the device switching frequency and behavior under different VIN voltage and
synchronized to an external 2.2-MHz system clock.
VIN
10V/Div
VIN
10V/Div
SW
10V/Div
SW
10V/Div
IL
IL
5A/Div
5A/Div
500.0ns/Div
500.0ns/Div
VIN = 8 V
L = 0.68 uH IPA_BUS = 3 A IPB_BUS = 3 A
VIN = 13.5 V
L = 0.68 uH IPA_BUS = 3 A IPB_BUS = 3 A
图10-5. Switching Frequency When RFREQ = 8.45
kΩ
图10-6. Switching Frequency When RFREQ = 8.45
kΩ
VIN
5V/Div
SYNC
VIN
10V/Div
2V/Div
SW
10V/Div
SW
10V/Div
IL
5A/Div
IL
5A/Div
500.0ns/Div
500.0ns/Div
VIN = 18 V
L = 0.68 uH IPA_BUS = 3 A IPB_BUS = 3 A
VIN = 8 V
L = 0.68 uH IPA_BUS = 3 A IPB_BUS = 3 A
图10-7. Switching Frequency When RFREQ = 8.45
kΩ
图10-8. Synchronizing to External 2.2-MHz Clock
Copyright © 2021 Texas Instruments Incorporated
28
Submit Document Feedback
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
VIN
10V/Div
VIN
10V/Div
SYNC
2V/Div
SYNC
2V/Div
SW
10V/Div
SW
10V/Div
IL
IL
5A/Div
5A/Div
500.0ns/Div
500.0ns/Div
VIN = 13.5 V
L = 0.68 uH IPA_BUS = 3 A IPB_BUS = 3 A
VIN = 18 V
L = 0.68 uH IPA_BUS = 3 A IPB_BUS = 3 A
图10-9. Synchronizing to External 2.2-MHz Clock
图10-10. Synchronizing to External 2.2-MHz Clock
10.3.5 Bootstrap Voltage (BOOT)
The TPS2585x-Q1 provides an integrated bootstrap voltage regulator. A small capacitor between the BOOT and
SW pins provides the gate drive voltage for the high-side MOSFET. The BOOT capacitor is refreshed when the
high-side MOSFET is off and the low-side switch conducts. The recommended value of the BOOT capacitor is
100 nF. A ceramic capacitor with an X7R or X5R grade dielectric with a voltage rating of 10 V or higher is
recommended for stable performance over temperature and voltage. The BOOT rail has a UVLO to protect the
chip from operation with too little bias, and is typically 2.2 V. If the BOOT capacitor voltage drops below the
UVLO threshold, the device initiates a charging sequence using the low-side FET before attempting to turn on
the high-side device.
10.3.6 Minimum ON-Time, Minimum OFF-Time
Minimum ON-time, TON_MIN, is the smallest duration of time that the HS switch can be on. TON_MIN is typically 84
ns in the TPS2585x-Q1. Minimum OFF-time, TOFF_MIN, is the smallest duration that the HS switch can be off.
TOFF_MIN is typically 81 ns in the TPS2585x-Q1. In CCM (FPWM) operation, TON_MIN and TOFF_MIN limit the
voltage conversion range given in a selected switching frequency.
The minimum duty cycle allowed is:
DMIN = TON_MIN × fSW
(5)
And the maximum duty cycle allowed is:
DMAX = 1 –TOFF_MIN × fSW
(6)
Given fixed TON_MIN and TOFF_MIN, the higher the switching frequency, the narrower the range of the allowed
duty cycle.
Given an output voltage, the choice of the switching frequency affects the allowed input voltage range, solution
size, and efficiency. The maximum operation supply voltage can be found by:
VOUT
V
=
IN_MAX
f
ì TON_MIN
SW
(7)
At lower supply voltage, the switching frequency is limited by TOFF_MIN. The minimum VIN can be approximated
by:
VOUT
V
=
IN_MIN
1- f
ì TOFF _MIN
SW
(8)
Considering power losses in the system with heavy load operation, VIN_MAX is higher than the result calculated in
方程式7.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
29
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
If minimum ON-time or minimum OFF-time do not support the desired conversion ratio, frequency is reduced,
automatically allowing regulation to be maintained during load dump and with very low dropout during cold crank
even with high operating-frequency setting.
10.3.7 Internal Compensation
The TPS2585x-Q1 is internally compensated. The internal compensation is designed such that the loop
response is stable over the specified operating frequency and output voltage range. The TPS2585x-Q1 is
optimized for transient response over the range of 200 kHz ≤fsw ≤3000 kHz.
10.3.8 Selectable Output Voltage (VSET)
The TPS2585x-Q1 provides four different output voltage options. The voltage can be set by an external resistor
across the VSET pin. The normal method of setting the buck output voltage is by selecting an appropriate value
VSET resistor as shown in 表10-2.
表10-2. VSET Configuration vs BUS Output Voltage
VSET CONFIGURATION
Float or pull up to VSENSE
Short to GND
VSENSE
5.1 V
5.17 V
5.3 V
RVSET = 40.2 KΩ
5.4 V
RVSET = 80.6 KΩ
Note that the VSET has an internal weak 20-µA current source to overdrive the pin to SENSE. If this pin is
floated, the voltage on this pin approaches the SENSE voltage, and sets the output voltage to 5.1 V. TI does not
recommend to float this pin if there is external noise from the PCB board, because the noise interferes with the
VSET internal logic block.
10.3.9 Current Limit and Short Circuit Protection
For maximum versatility, the TPS2585x-Q1 includes both a precision, programmable current limit as well cycle-
by-cycle current limit to protect the USB port from extreme overload conditions. The RILIM resistor determines the
overload threshold on the USB ports in the event ILIM is shorted to ground to set the default USB current limit.
The cycle-by-cycle current limit serves as a backup means of protection.
10.3.9.1 USB Switch Programmable Current Limit (ILIM)
Because the TPS2585x-Q1 integrates two USB current-limit switches, it provides adjustable current limit to
prevent USB port overheating. The device engages the two-level current limit scheme, which has one typical
current limit, IOS_BUS, and the secondary current limit, IOS_HI. The secondary current limit, IOS_HI, is 1.6x the
primary current limit, IOS_BUS. The secondary current limit acts as the current limit threshold for a deglitch time,
tIOS_HI_DEG, then the USB power switch current limit threshold is set back to IOS_BUS. 方程式 9 calculates the
value of resistor for adjusting the typical current limit.
32273
RILIM Kꢀ =
(
)
IOS _BUS (mA)
(9)
This equation assumes an ideal-no variation-external adjusting resistor. To take resistor tolerance into account,
first determine the minimum and maximum resistor values based on its tolerance specifications and use these
values in the equations. Because of the inverse relationship between the current limit and the adjusting resistor,
use the maximum resistor value in the IOS(min) equation and the minimum resistor value in the IOS(max) equation.
Typical RILIM resistor value are listed in 表10-3.
Copyright © 2021 Texas Instruments Incorporated
30
Submit Document Feedback
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
表10-3. Setting the Current Limit with RILIM
IOS_BUS - Current Limit Threshold (mA)
RILIM (KΩ)
19.1
1690
2096
2806
3386
3550
15.4
11.5
9.53
Short to GND
For the normal application, it can short the ILIM pin to GND directly, which sets a default 3.55-A current limit with
a maximum ±15% variation on each USB port to follow the Type-C specification. The TPS2585x-Q1 provides
built-in soft-start circuitry that controls the rising slew rate of the output voltage to limit inrush current and voltage
surges.
The secondary current limit, IOS_HI, allows the USB port pull out a larger current for a short time during transient
overload conditions, which can bring benefits for USB port special overload testing like MFi OCP. In a normal
application, once the device is powered on and USB port is not in UVLO, the USB port current limit threshold is
overridden by the secondary current limit, IOS_HI, so the USB port can output as high as a 1.6 × IOS_BUS current
for typically 2 ms. After the deglitch time, tIOS_HI_DEG, the current limit threshold is set back to the typical current
with IOS_BUS. The secondary current limit threshold does not resume until after the tIOS_HI_RST deglitch time,
which is typically 16 ms. If there is an inrush current higher than the IOS_HI threshold, the current limit is set back
to IOS_BUS immediately, without waiting for a tIOS_HI_DEG
.
The TPS2585x-Q1 responds to overcurrent conditions by limiting output current to IOS_BUS as shown in previous
equation. When an overload condition occurs, the device maintains a constant output current and the output
voltage reduces accordingly. Three possible overload conditions can occur:
• The first condition is when a short circuit or overload is applied to the USB output when the device is powered
up or enabled. There can be inrush current and once it triggers the approximate 8-A threshold, a fast turnoff
circuit is activated to turn off the USB power switch within tIOS_USB before the current limit control loop is able
to respond (shown in 图10-11). After the fast turnoff is triggered, the USB power switch current-sense
amplifier is over-driven during this time and momentarily disables the internal N-channel MOSFET to turn off
USB port. The current-sense amplifier then recovers and ramps the output current with a soft start. If the USB
port is still in overcurrent condition, the short circuit and overload hold the output near zero potential with
respect to ground and the power switch ramps the output current to IOS_BUS. If the overcurrent limit condition
lasts longer than 4.1 ms, the corresponding USB channel enters hiccup mode with 524 ms of off-time and 4.1
ms of on-time.
IBUS
IOS_BUS
t
hiccup OFF
hiccup ON
tIOS
图10-11. Response Time to BUS Short-Circuit
• The second condition is the load current increases above IOS_BUS but below the IOS_HI setting. The device
allows the USB port to output this large current for tIOS_HI_DEG, without limiting the USB port current to
IOS_BUS. After the tIOS_HI_DEG deglitch time, the device limits the output current to IOS_BUS and works in a
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
31
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
constant current-limit mode. If the load demands a current greater than IOS_BUS, the USB output voltage
decreases to IOS_BUS × RLOAD for a resistive load, which is shown in 图10-12. If the overcurrent limit
condition lasts longer than 4.1 ms, the corresponding USB channel enters hiccup mode with 524 ms of off-
time and 4.1 ms of on-time. Another USB channel still works normally.
I
BUS(A)
V
BUS(V)
5
IOS_HI
IOS_BUS
0
hiccup OFF
hiccup OFF
hiccup ON
hiccup ON
tIOS_HI_DEG
t
图10-12. BUS Overcurrent Protection
• The third condition is the load current increases just over the IOS_HI setting. In this case, the load current does
not trigger the fast turnoff. The USB power switch current limit threshold is set back to the primary current
limit, IOS_BUS, immediately. If the load still demands a current greater than IOS_BUS, the USB output voltage
decreases to IOS_BUS × RLOAD for a resistive load, which is shown in 图10-13. If the overcurrent limit
condition lasts longer than 4.1 ms, the corresponding USB channel enters hiccup mode with 524 ms of off-
time and 4.1 ms of on-time. Another USB channel still works normally.
I
BUS(A)
V
BUS(V)
5
IOS_HI
IOS_BUS
0
hiccup OFF
hiccup OFF
hiccup ON
hiccup ON
t
图10-13. BUS Overcurrent Protection: Two-Level Current Limit
The TPS2585x-Q1 thermal cycles if an overload condition is present long enough to activate thermal limiting in
any of the previously mentioned cases. Thermal limiting turns off the internal NFET and starts when the NFET
junction temperature exceeds 160°C (typical). The device remains off until the NFET junction temperature cools
10°C (typical) and then restarts. This extra thermal protection mechanism can help prevent further junction
temperature rise, which can cause the device to turn off due to junction temperature exceeding the main thermal
shutdown threshold, TSD
.
10.3.9.2 Interlocking for Two-Level USB Switch Current Limit
The TPS2585x-Q1 has two USB ports. Because the secondary current limit, IOS_HI, is 1.6x of the primary current
limit, IOS_BUS, if the two USB ports pull out large current at the same time, then the DC/DC regulator is
overloaded, and DC/DC regulator output voltage can be crashed. To avoid these potential issues, the
TPS2585x-Q1 adopts the interlocking scheme to manage the current limits of the two USB ports.
Copyright © 2021 Texas Instruments Incorporated
32
Submit Document Feedback
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
For interlocking, if one USB port current is beyond the primary current limit threshold, IOS_BUS, then another USB
port current limit threshold is overridden to the primary current limit, IOS_BUS, immediately. With this control
scheme, the TPS2585x-Q1 only allows one USB port to output a large current, which can be as high as 1.6x of
the primary current limit, IOS_BUS, at the same time. Ensure the DC/DC regulator has enough energy to sustain
its output voltage. That means in MFi OCP testing, the DC/DC regulator supports up to 8.4 A output current
during the tIOS_HI_DEG deglitch time, which 4.8 A for the USB type-C port which under testing, 3 A for another
USB type-C port, and maximum 0.6 A total for VCONN and OUT.
10.3.9.3 Cycle-by-Cycle Buck Current Limit
There is a buck regulator cycle-by-cycle current limit on both the peak and valley of the inductor current.
High-side MOSFET overcurrent protection is implemented by the nature of the peak current mode control. The
HS switch current is sensed when the HS is turned on after a set blanking time. The HS switch current is
compared to the output of the Error Amplifier (EA) minus slope compensation every switching cycle. The peak
current of HS switch is limited by a clamped maximum peak current threshold, IHS_LIMIT, which is constant. The
peak current limit of the high-side switch is not affected by the slope compensation and remains constant over
the full duty cycle range.
The current going through LS MOSFET is also sensed and monitored. When the LS switch turns on, the inductor
current begins to ramp down. The LS switch does not turn OFF at the end of a switching cycle if its current is
above the LS current limit, ILS_LIMIT. The LS switch is kept ON so that the inductor current keeps ramping down
until the inductor current ramps below the LS current limit, ILS_LIMIT. Then, the LS switch is turned OFF and the
HS switch is turned on after a dead time. This action is somewhat different than the more typical peak current
limit, and results in 方程式10 for the maximum load current.
V
IN - VOUT
(
)
ì
VOUT
IOUT _MAX = ILS _LIMIT
+
2ì fSW ìL
V
IN
(10)
10.3.9.4 OUT Current Limit
The TPS2585x-Q1 can provide 200-mA current at the OUT pin to power the auxiliary loads, such as USB HUB,
LEDs. The input of the OUT power switch comes from the buck regulator output, so the OUT voltage is same
with the SENSE voltage, but deduct the OUT RDS-ON voltage loss.
Because the OUT power is provided by buck regulator, for TPS25850-Q1, the buck regulator is not operating
unless Rd is inserted. In normal application, if no USB Type-C cable plug-in, then TPS25850-Q1 OUT voltage is
zero. For TPS25851-Q1 and TPS25852-Q1, the buck regulator will operate even though Rd is not inserted, so
even if no USB Type-C cable plug-in, the TPS25851-Q1 and TPS25852-Q1 OUT still have a voltage same with
the SENSE voltage.
If the OUT current reaches the current limit level, the OUT pin MOSFET works in a constant current-limit mode.
If the overcurrent limit condition lasts longer than 4.1 ms, it enters hiccup mode with 4.1 ms of on-time and 524
ms of off-time.
10.3.10 Cable Compensation
When a load draws current through a long or thin wire, there is an IR drop that reduces the voltage delivered to
the load. In the vehicle from the voltage regulator output VOUT to VBUS (input voltage of portable device), the total
resistance of PCB trace, connector, and cable resistances causes an IR drop at the portable device input, so the
charging current of most portable devices is less than their expected maximum charging current. The voltage
drop is shown in 图10-14.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
33
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
5.x
V(DROP)
VOUT with compensation
VBUS with compensation
VBUS without compensation
3
1
2
Output Current (A)
图10-14. Voltage Drop
To handle this case, the TPS2585x-Q1 has a built-in cable compensation function where the droop
compensation linearly increases the voltage at the SENSE pin of the TPS2585x-Q1 as load current increases, to
maintain a fairly constant output voltage at the load-side voltage.
The TPS2585x-Q1 internal comparator compares the current-sense output voltage of the two current-limit
switches and uses the larger current-sense output voltage to compensate for the line drop voltage. The cable
compensation amplitude increases linearly as the load current increases. The cable compensation also has an
upper limitation. The cable compensation at output currents greater than 2.4 A is 90 mV and is shown in 图
10-15. Note the cable compensation only works when you short the VSET to GND. For the other VSET
configuration, the cable compensation is not available.
VSENSE
5.26V
5.17V
IPA/B_BUS
2.4A
图10-15. Dual Ports Cable Compensation
10.3.11 Thermal Management With Temperature Sensing (TS) and OTSD
The TS input pin allows for user-programmable thermal protection (for the TS pin thresholds, see the Electrical
Characteristics). The TS input pin threshold is ratiometric with VSENSE. The external resistor divider setting, VTS,
must be connected to the TPS2585x-Q1 SENSE pin to achieve accurate results (refer to the 图 10-16). When
VTS = 0.5 × VSENSE, the TPS2585x-Q1 performs below action:
• If operating with 3-A Type-C advertisement, the Px_CC1, Px_CC2 pin automatically reduces advertisement to
the 1.5-A level.
Copyright © 2021 Texas Instruments Incorporated
34
Submit Document Feedback
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
VSENSE
RSER
VSENSE
RPARA
RNTC
TS
CC override
(3A -> 1.5A)
Vth9 ≈ 0.5 x VSENSE
RB
Vhys ≈ 500mV
TS_TEMP_HOT
Vth9 ≈ 0.65 x VSENSE
Vhys ≈ 500mV
图10-16. TS Input
If the overtemperature condition persists, causing VTS = 0.65 × VSENSE, the TPS2585x-Q1 performs below
actions:
• Broadcasts the default USB power mode, in default USB power, the charging is ideally reduced further per
the USB2.0 and USB3.0 specification.
• Buck regulator output voltage at the SENS pin is reduced to 4.77 V.
If the overtemperature condition persists, causing TJ to reach the OTSD threshold, then the device thermal shuts
down.图 10-17 shows the TPS25850-Q1 behavior when TS pin voltage trigger the Temp Warm and Temp Hot
threshold.
ICCx (uA)
VBUS (V)
BUS Voltage
5.1
4.77
330
CC Broad Current
180
80
T1(Temp Warm)
T2(Temp Hot)
OTSD
图10-17. TPS25850-Q1 Behavior When Trigger Temp Warm/Hot Threshold
The NTC thermistor must be placed near the hottest point on the PCB. In most cases, this placement is close to
the SW node of the TPS2585x-Q1, near the buck inductor.
Tuning the VNTC threshold levels of VTEMP_WARM and VTEMP_HOT is achieved by adding RSER, RPARA, or both
RSER and RPARA in conjunction with RNTC. 图 10-18 is an example illustrating how to set the VTEMP_WARM
threshold between 81°C and 90°C with a ΔT between TEMP_WARM assertion and TEMP_HOT assertion of
18°C to 29°C. Consult the chosen NTC manufacturer's specification for the value of β. Establishing the desired
warning and shutdown thresholds can take some iteration.
Below is NTC spec and resistor value used in 图10-18 example.
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
35
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
• R0 = 470 kΩ. β= 4750. RNTC = R0 × exp β× (1/T –1/T0).
• RPARA = 100 kΩ.
• RSER = 5.1 kΩ.
• RB = RNTC(at TEMP_WARM) = 27 kΩ.
5
4.5
4
3.5
3
VTS (V)
VTS w/ top ser (V)
VTS w/ top || (V)
VTS w/ para + ser (V)
TEMP_WARM
TEMP_HOT
2.5
2
1.5
1
0.5
0
0
20
40
60
80
100
120
140
NTC Temperature (°C)
T NTC (°C)
90
Rising Thresholds
Temp Warm
Temp Hot
V (V)
T NTC || (°C) T NTC ser (°C) T NTC || + ser (°C)
=VSENSE * 0.5
=VSENSE * 0.65
2.55
3.315
81
103
22
95
121
26
89
118
29
108
TEMP_HOT - TEMP_WARM
18
图10-18. VTS Threshold Design Examples
10.3.12 Thermal Shutdown
The device has an internal overtemperature shutdown threshold, TSD, to protect the device from damage and
overall safety of the system. When the device temperature exceeds TSD, the device is turned off when thermal
shutdown activates. Once the die temperature falls below 154°C (typ.), the device reinitiates the power-up
sequence controlled by the internal soft-start circuitry.
10.3.13 USB Enable On/Off Control (TPS25852-Q1)
The PA_EN and PB_EN are the on/off control input pins for PA_USB and PB_USB, respectively. The USB
switch is active when Px_EN is pulled high. Pull the Px_EN voltage to logic low to shut down the USB switch
with an output discharge. Connect Px_EN to SENSE for automatic start-up, or control them by an external on/off
signal from the microcontroller or USB HUB.
10.3.14 FAULT Indication (TPS25851-Q1 and TPS25852-Q1)
For the TPS25851-Q1 and TPS25852-Q1, PA_FAULT and PB_FAULT are the fault indication pins for PA_USB
and PB_USB, respectively. FAULT is in an open-drain state during shutdown, start-up, or normal condition.
When the USB switch enters hiccup mode, or overtemperature thermal shutdown (OTSD) is triggered,
Px_FAULT is pulled low. FAULT asserts (logic low) on an individual USB switch during an over-current or
overtemperature condition. Px_FAULT switches high after the fault condition is removed, and the USB output
voltage goes high again.
Copyright © 2021 Texas Instruments Incorporated
36
Submit Document Feedback
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
The device features an active-low, open-drain fault output. Connect a 100-kΩ pullup resistor from Px_FAULT to
SENSE or other suitable I/O voltage. Px_FAULT can be left open or tied to GND when not used.
表10-4 summarizes the conditions that generate a fault and actions taken by the device.
表10-4. Fault Conditions
EVENT
CONDITION
ACTION
Px_BUS load switch enter hiccup mode. The fault indicator
asserts with a 4.1-ms deglitch and de-asserts with a 16.4-ms
deglitch. The fault indicator remains asserted during the
Px_BUS overload condition.
Over-current on Px_BUS
IPx_BUS > Programmed IILIM
The device immediately disables and asserts fault indicator
with no deglitch. The device attempts to power up once the
die temperature decreases below the thermal hysteresis
threshold as specified.
TPS2585x-Q1
overtemperature
TJ > TSD
10.3.15 USB Specification Overview
All USB ports are capable of providing a 5-V output, making them a convenient power source for operating and
charging portable devices. USB specification documents outline specific power requirements to ensure
interoperability. In general, a USB 2.0 port host port is required to provide up to 500 mA; a USB 3.0 or USB 3.1
port is required to provide up to 900 mA; ports adhering to the USB Battery Charging 1.2 Specification provide
up to 1500 mA; newer Type-C ports can provide up to 3000 mA. Though USB standards governing power
requirements exist, some manufacturers of popular portable devices created their own proprietary mechanisms
to extend allowed available current beyond the 1500-mA maximum per BC 1.2. While not officially part of the
standards maintained by the USB-IF, these proprietary mechanisms are recognized and implemented by
manufacturers of USB charging ports.
The TPS2585x-Q1 device supports five of the most-common USB-charging schemes found in popular hand-held
media and cellular devices:
• USB Type-C (1.5-A and 3-A advertisement)
• USB Battery Charging Specification BC1.2 DCP mode
• Chinese Telecommunications Industry Standard YD/T 1591-2009
• Divider 3 mode
• 1.2-V mode
10.3.16 USB Type-C® Basics
For a detailed description of the Type-C specification, refer to the USB-IF website to download the latest
released version. Some of the basic concepts of the Type-C spec that pertains to understanding the operation of
the TPS2585x-Q1 (a DFP device) are described as follows.
USB Type-C removes the need for different plug and receptacle types for host and device functionality. The
Type-C receptacle replaces both the Type-A and Type-B receptacles because the Type-C cable is plug-able in
either direction between the host and device. A host-to-device logical relationship is maintained by the
configuration channel (CC). Optionally, hosts and devices can be either providers or consumers of power when
USB PD communication is used to swap roles.
All USB Type-C ports operate in one of following data modes:
• Host mode: The port can only be a host (provider of power).
• Device mode: The port can only be a device (consumer of power).
• Dual-Role mode: The port can be either a host or device.
Port types:
• DFP (Downstream Facing Port): Host
• UFP (Upstream Facing Port): Device
• DRP (Dual-Role Port): Host or Device
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
37
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
Valid DFP-to-UFP connections:
• 表10-5 describes valid DFP-to-UFP connections.
• Host-to-Host or Device-to-Device have no functions.
表10-5. DFP-to-UFP Connections
DEVICE-MODE
PORT
HOST-MODE PORT
DUAL-ROLE PORT
Host-Mode Port
Device-Mode Port
Dual-Role Port
No function
Works
Works
No function
Works
Works
Works
Works
Works(1)
(1) This port can be automatic or manually driven.
10.3.16.1 Configuration Channel
The function of the configuration channel is to detect connections and configure the interface across the USB
Type-C cables and connectors.
Functionally, the Configuration Channel (CC) is used to serve the following purposes:
• Detect connect to the USB ports.
• Resolve cable orientation and twist connections to establish USB data bus routing.
• Establish DFP and UFP roles between two connected ports.
• Discover and configure power: USB Type-C current modes or USB Power Delivery.
• Discover and configure optional Alternate and Accessory modes.
• Enhances flexibility and ease of use.
Typical flow of DFP-to-UFP configuration is shown in 图10-19.
图10-19. Flow of DFP-to-UFP Configuration
10.3.16.2 Detecting a Connection
DFPs and DRPs fulfill the role of detecting a valid connection over USB Type-C. 图 10-20 shows a DFP-to-UFP
connection made with a Type-C cable. As shown in 图 10-20, the detection concept is based on being able to
detect terminations in the product that have been attached. A pull-up and pull-down termination model is used. A
pull-up termination can be replaced by a current source.
• In the DFP-UFP connection, the DFP monitors both CC pins for a voltage lower than the unterminated
voltage.
• An UFP advertises Rd on both its CC pins (CC1 and CC2).
• A powered cable advertises Ra on only one of the CC pins of the plug. Ra is used to inform the source to
apply VCONN.
• An analog audio device advertises Ra on both CC pins of the plug, which identifies it as an analog audio
device. VCONN is not applied on either CC pin in this case.
Copyright © 2021 Texas Instruments Incorporated
38
Submit Document Feedback
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
UFP monitors for
connection
DFP monitors for
connection
Cable
CC
Rp
Rp
Rds
Rds
Ra
Ra
DFP monitors for
connection
UFP monitors for
connection
图10-20. DFP-UFP Connection
For USB Type-C solutions, two pins (CC1, CC2) on the connector are used to establish and manage the source-
to-sink connection. The general concept for setting up a valid connection between a source and a sink is based
on being able to detect terminations residing in the product being attached. To aid in defining the functional
behavior of CC, a pull-up (Rp) and pull-down (Rd 5.1 kΩ) termination model is used based on a pull-up resistor
and pull-down resistor.
Initially, a source exposes independent Rp terminations on its CC1 and CC2 pins, and a sink exposes
independent Rd terminations on its CC1 and CC2 pins. The source-to-sink combination of this circuit
configuration represents a valid connection. To detect this connection, the source monitors CC1 and CC2 for a
voltage lower than its unterminated voltage. The choice of Rp is a function of the pull-up termination voltage and
the detection circuit of the source. This indicates that either a sink, a powered cable, or a sink connected by a
powered cable has been attached. Prior to the application of VCONN, a powered cable exposes Ra (typically 1
kΩ) on its VCONN pin. Ra represents the load on VCONN plus any resistive elements to ground. In some cable
plugs, this can be a pure resistance, and in others, it can simply be the load.
The source must be able to differentiate between the presence of Rd and Ra to know whether there is a sink
attached and where to apply VCONN. The source is not required to source VCONN unless Ra is detected. Two
special termination combinations on the CC pins as seen by a source are defined for directly attached accessory
modes: Ra/Ra for audio adapter accessory mode and Rd/Rd for debug accessory mode.
10.3.16.3 Plug Polarity Detection (TPS25851-Q1)
Reversible Type-C plug orientation is reported by the Px_POL pin when a UFP is connected. However, when
there is no UFP attached, Px_POL remains de-asserted irrespective of cable plug orientation. 表 10-6 describes
the Px_POL state based on which device CC pin detects VRD from an attached UFP pulldown.
表10-6. Plug Polarity Detection
Px_CC1
Rd
Px_CC2
Open
Rd
Px_POL
STATE
Hi-Z
UFP connected
Open
Asserted (pulled low)
UFP connected with reverse plug orientation
10.3.17 USB Port Operating Modes
10.3.17.1 USB Type-C® Mode
The TPS2585x-Q1 is a Type-C controller that supports all Type-C functions in a downstream facing port. The
TPS2585x-Q1 is also used to manage current advertisement and protection to a connected UFP and active
cable. When VSENSE exceeds the undervoltage lockout threshold, the device samples the EN pin. A high level on
this pin enables the device and normal operation begins. Having successfully completed its start-up sequence,
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
39
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
the device now actively monitors its CC1 and CC2 pins for attachment to a UFP. When a UFP is detected on
either the CC1 or CC2 pin the USB power switch turn-ons. If Ra is detected on the other CC pin (not connected
to UFP), VCONN is applied to allow current to flow to the CC pin connected to Ra.
10.3.17.2 Dedicated Charging Port (DCP) Mode (TPS25850-Q1 Only)
A DCP only provides power and does not support data connection to an upstream port. As shown in the
following sections, a DCP is identified by the electrical characteristics of the data lines. The TPS25850-Q1 only
emulates one state, DCP-auto state. In the DCP-auto state, the device charge-detection state machine is
activated to selectively implement charging schemes involved with the shorted, Divider 3 and 1.2-V modes. The
shorted DCP mode complies with BC1.2 and Chinese Telecommunications Industry Standard YD/T 1591-2009,
whereas the Divider 3 and 1.2-V modes are employed to charge devices that do not comply with the BC1.2 DCP
standard.
10.3.17.2.1 DCP BC1.2 and YD/T 1591-2009
Both standards specify that the D+ and D– data lines must be connected together with a maximum series
impedance of 200 Ω, as shown in 图10-21.
VBUS
5 V
D–
200 Ω
(ma x.)
D+
GND
图10-21. DCP Supporting BC1.2 and YD/T 1591-2009
10.3.17.2.2 DCP Divider-Charging Scheme
The device supports Divider 3, as shown in 图 10-22. In the Divider 3 charging scheme the device applies 2.7 V
and 2.7 V to D+ and D–data lines.
VBUS
5 V
D–
D+
2.7 V
2.7 V
GND
图10-22. Divider 3 Mode
10.3.17.2.3 DCP 1.2-V Charging Scheme
The DCP 1.2-V charging scheme is used by some hand-held devices to enable fast charging at 2 A. The
TPS25850-Q1 device supports this scheme in DCP-auto state before the device enters BC1.2 shorted mode. To
simulate this charging scheme, the D+ and D– lines are shorted and pulled up to 1.2 V for a fixed duration.
Then the device moves to DCP shorted mode as defined in the BC1.2 specification and as shown in 图10-23.
VBUS
5 V
200 Ω (ma x.) D–
D+
1.2 V
GND
图10-23. 1.2-V Mode
Copyright © 2021 Texas Instruments Incorporated
40
Submit Document Feedback
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
10.3.17.3 DCP Auto Mode (TPS25850-Q1)
The TPS25850-Q1 device integrates an auto-detect state machine that supports all the DCP charging schemes
as shown in 图 10-24. The auto-detect state machine starts in the Divider 3 scheme. If a BC1.2 or YD/T
1591-2009 compliant device is attached, the TPS25850-Q1 device responds by turning the power switch back
on without output discharge and operating in 1.2-V mode briefly before entering BC1.2 DCP mode. Then, the
auto-detect state machine stays in that mode until the device releases the data line, in which case, the auto-
detect state machine goes back to the Divider 3 scheme. When a Divider 3-compliant device is attached, the
TPS25850-Q1 device stays in the Divider 3 state.
5 V
S1
Divider 3 Mode
VBUS
S1, S2: ON
S3, S4: OFF
DM_IN
DP_IN
GND
D–
D+
S2
S3
S4
Shorted Mode
S4 ON
S1, S2, S3: OFF
GND
1.2-V Mode
S1, S2: OFF
S3, S4: ON
2.7 V 2.7 V 1.2 V
图10-24. DCP Auto Mode
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
41
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
10.4 Device Functional Modes
10.4.1 Shutdown Mode
The EN pin provides electrical ON and OFF control for the TPS2585x-Q1. When VEN is below 1.2 V (typical), the
device is in shutdown mode. The TPS2585x also employs VIN overvoltage lock out protection and VSENSE
undervoltage lock out protection. If VIN voltage is above its respective OVLO level VOVLO, or VSENSE voltage is
below its respective UVLO level VDCDC_UVLO, the DC/DC converter turns off.
10.4.2 Active Mode
The TPS2585x-Q1 is in active mode when VEN is above the precision enable threshold, VSENSE is above its
respective UVLO levels and a valid detection has been made on the CC lines. The simplest way to enable the
TPS2585x-Q1 is to connect the EN pin to SENSE pin. This connection allows self startup when the input voltage
is in the operating range (5.5 V to 26 V) and a UFP detection is made.
In active mode, the TPS25850-Q1 buck regulator does not operate unless Rd is inserted, the TPS25851-Q1 and
TPS25852-Q1 buck regulator operates even though Rd is not inserted. Then the buck regulator operates with
Forced Pulse Width Modulation (FPWM), also referred to as Forced Continuous Conduction Mode (FCCM). This
action ensures the buck regulator switching frequency remains constant under all load conditions. FPWM
operation provides low output voltage ripple, tight output voltage regulation, and constant switching frequency.
Built-in spread-spectrum modulation aids in distributing spectral energy across a narrow band around the
switching frequency programmed by the FREQ/SYNC pin. Under light load conditions the inductor current is
allowed to go negative. A negative current limit of IL-NEG-LS is imposed to prevent damage to the regulator's low
side FET. During operation, the TPS2585x-Q1 synchronizes to any valid clock signal on the FREQ/SYNC input.
Copyright © 2021 Texas Instruments Incorporated
42
Submit Document Feedback
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
11 Application and Implementation
Note
以下应用部分中的信息不属于TI 器件规格的范围,TI 不担保其准确性和完整性。TI 的客 户应负责确定
器件是否适用于其应用。客户应验证并测试其设计,以确保系统功能。
11.1 Application Information
The TPS2585x-Q1 is a step down DC-to-DC regulator and USB charge port controller. The device typically used
in automotive systems to convert a DC voltage from the vehicle battery to 5-V DC with a maximum output
current of 6.6-A in dual Type-C ports applications. The TPS2585x-Q1 engages a high efficiency buck converter,
letting the device operate at as high as 85°C ambient temperature with full load. The following design procedure
can be used to select components for the TPS2585x-Q1.
11.2 Typical Applications
The TPS2585x-Q1 only requires a few external components to convert from a wide voltage range supply to a 5-
V output to power USB devices. 图 11-1 shows the TPS25850-Q1 typical application schematic for Dual Type-C
charging ports.
SW
IN
22mF
22mF 22mF
BATT
100nF
BOOT
PGND
22mF
0.1mF
VSENSE
EN
VSENSE
VSENSE
SENSE
OUT
BIAS
1mF
TPS25850-Q1
1mF
IBUS=3A
VSENSE
PA_BUS
PA_DM
PA_DP
1mF
TS
PA_CC1
PA_CC2
1mF
IBUS=3A
PB_BUS
VSET
ILIM
PB_DM
PB_DP
FREQ/SYNC
AGND
PB_CC1
PB_CC2
1mF
图11-1. TPS25850-Q1 Typical Application Circuit for 2.1-MHz fSW
As a quick start guide, 表 11-1 provides typical component values for some of the most common configurations.
The values given in 表 11-1 are typical. Other values can be used to enhance certain performance criterion as
required by the application. The integrated buck regulator of TPS2585x-Q1 is internally compensated and
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
43
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
optimized for a reasonable selection of external inductance and capacitance. The external components have to
fulfill the needs of the application, but also the stability criteria of the control loop of the device.
表11-1. L and COUT Typical Values
VOUT WITHOUT CABLE
fSW
L
CHF + CIN
CBOOT
RATED COUT
COMPENSATION
400 KHZ
2.1 MHz
5.17 V
3.3 µH
1 × 100 nF + 1 × 47 µF
1 × 100 nF + 1 × 22 µF
1 × 100 nF
1 × 100 nF
3 × 47 µF
3 × 22 µF
5.17 V
0.68 µH
1. The inductance value is calculated based on max VIN = 18 V.
2. All the COUT values are after derating and use low ESR ceramic capacitors.
3. The COUT is the buck regulator output capacitors at the SENSE pin.
11.2.1 Design Requirements
The detailed design procedure is described based on a design example. For this design example, use the
parameters listed in 表11-2 as the input parameters.
表11-2. Design Example Parameters
Input voltage, VIN
13.5-V typical, range from 8 V to 18 V
Output voltage, VSENSE
Maximum output current
Switching frequency, fSW
5.17 V
6.6 A
2.1 MHz
11.2.2 Detailed Design Procedure
11.2.2.1 Output Voltage Setting
The output voltage of TPS2585x-Q1 is programmed by the VSET pin, and if short VSET to GND, sets the output
voltage at 5.17 V and enables the cable compensation function, and the output voltage increases linearly with
increasing load current. Refer to 表 10-2 for more details on output voltage setting. Cable compensation can be
used to increase the voltage on the SENSE pin linearly with increasing load current. Refer to the list item in
Ground Plane and Thermal Considerations section for more details on cable compensation setting. If cable
compensation is not desired, use a 0-ΩRIMON resistor.
11.2.2.2 Switching Frequency
The recommended switching frequency of the TPS2585x-Q1 is in the range of 250 KHz–400 KHz for high
efficiency. Choose RFREQ = 49.9 kΩ for 400-KHz operation. To choose a different switching frequency, refer to
表10-1.
The choice of switching frequency is a compromise between conversion efficiency and overall solution size.
Lower switching frequency implies reduced switching losses and usually results in higher system efficiency.
However, higher switching frequency allows the use of smaller inductors and output capacitors, and hence, a
more compact design. In automotive USB charging applications, it tends to operate at either 400 kHz below the
AM band, or 2.1 MHz above the AM band. In this example, 2.1 MHz is chosen.
11.2.2.3 Inductor Selection
The most critical parameters for the inductor are the inductance, saturation current, and the rated current. The
inductance is based on the desired peak-to-peak ripple current, ΔiL. Because the ripple current increases with
the input voltage, the maximum input voltage is always used to calculate the minimum inductance LMIN. Use 方
程式 12 to calculate the minimum value of the output inductor. KIND is a coefficient that represents the amount of
inductor ripple current relative to the maximum output current of the device. A reasonable value of KIND must be
20% to 40%. Note that when selecting the ripple current for applications with much smaller maximum load than
the maximum available from the device, the maximum device current must still be used. During an instantaneous
short or overcurrent operation event, the RMS and peak inductor current can be high. The inductor current rating
must be higher than the current limit of the device.
Copyright © 2021 Texas Instruments Incorporated
44
Submit Document Feedback
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
VOUT ì V
- VOUT
(
)
IN_MAX
DiL =
VIN_MAX ìL ì fSW
(11)
(12)
V
- VOUT
VOUT
IN_MAX
LMIN
=
ì
IOUT ìKIND
V
IN_MAX ì fSW
In general, Choose lower inductance in switching power supplies because it usually corresponds to faster
transient response, smaller DCR, and reduced size for more compact designs. Too low of an inductance can
generate too large of an inductor current ripple such that overcurrent protection at the full load can be falsely
triggered. Too low of an inductance also generates more conduction loss and inductor core loss. Larger inductor
current ripple also implies larger output voltage ripple with the same output capacitors. With peak current mode
control, TI does not recommend to have too small of an inductor current ripple. A larger peak current ripple
improves the comparator signal to noise ratio.
For this design example, choose KIND = 0.3, and find an inductance of approximately 0.682 µH. Select the next
standard value of 0.68 μH.
11.2.2.4 Output Capacitor Selection
The output capacitor or capacitors, COUT, must be chosen with care because it directly affects the steady state
output voltage ripple, loop stability, and the voltage overshoot or undershoot during load current transients.
The value of the output capacitor and its ESR, determine the output voltage ripple and load transient
performance. The output capacitor is usually limited by the load transient requirements rather than the output
voltage ripple if the system requires tight voltage regulation with presence of large current steps and fast slew
rate. When a fast large load increase happens, output capacitors provide the required charge before the inductor
current can slew up to the appropriate level. The control loop of the regulator usually needs four or more clock
cycles to respond to the output voltage droop. The output capacitance must be large enough to supply the
current difference for four clock cycles to maintain the output voltage within the specified range. 表 11-3 can be
used to find output capacitors for a few common applications. In this example, good transient performance is
desired giving 3 x 22-µF ceramic as the output capacitor.
表11-3. Selected Output Capacitor
FREQUENCY
2.1 MHz
COUT
SIZE AND COST
TRANSIENT PERFORMANCE
3 × 22 µF ceramic
Small size
Good
Better
2.1 MHz
2 × 47 µF ceramic
Small size
2.1 MHz
2 × 22 µF ceramic
Smallest size
Small size
Minimum
Good
400 KHz
400 KHz
400 KHz
3 × 47 µF ceramic
2 × 47 µF ceramic
Small size
Minimum
Good
Larger size, low cost
4 × 22 µF + 1 × 260 µF, < 50-mΩ electrolytic
1 × 4.7 µF + 2 × 10 µF + 1 × 260 µF, < 50-
400 KHz
Lowest cost
Minimum
mΩ electrolytic
where
• KIND = Ripple ratio of the inductor ripple current (ΔiL / IOUT
• IOL = Low level output current during load transient
• IOH = High level output current during load transient
• VUS = Target output voltage undershoot
)
• VOS = Target output voltage overshoot
11.2.2.5 Input Capacitor Selection
The TPS2585x-Q1 device requires a high frequency input decoupling capacitor or capacitors, depending on the
application. A high-quality ceramic capacitor type X5R or X7R with sufficient voltage rating is recommended. The
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
45
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
ceramic input capacitors provide a low impedance source to the converter in addition to supplying the ripple
current and isolating switching noise from other circuits. The typical recommended value for the high frequency
decoupling capacitor is 10 μF of ceramic capacitance. This must be rated for at least the maximum input
voltage that the application requires; preferably twice the maximum input voltage. This capacitance can be
increased to help reduce input voltage ripple, maintain the input voltage during load transients, or both. In
addition, a small case size 100-nF ceramic capacitor must be used at IN and PGND, immediately adjacent to the
converter. This action provides a high frequency bypass for the control circuits internal to the device. For this
example a 10-μF, 50-V, X7R (or better) ceramic capacitor is chosen, and the 100-nF ceramic capacitor must
also be rated at 50 V with an X7R or better dielectric.
Additionally, an electrolytic capacitor on the input in parallel with the ceramics can be required, especially if long
leads from the automotive battery to the IN pin of the TPS2585x-Q1, cold or warm engine crank requirements,
and so forth. The moderate ESR of this capacitor is used to provide damping to the voltage spike due to the lead
inductance of the cable or the trace.
11.2.2.6 Bootstrap Capacitor Selection
The TPS2585x-Q1 design requires a bootstrap capacitor (CBOOT). The recommended capacitor is 100 nF and
rated 16 V or higher. The bootstrap capacitor is located between the SW pin and the BOOT pin. The bootstrap
capacitor stores energy that is used to supply the gate drivers for the power MOSFETs. The bootstrap capacitor
must be a high-quality ceramic type with an X7R or X5R grade dielectric for temperature stability.
11.2.2.7 Undervoltage Lockout Set-Point
The system undervoltage lockout (UVLO) is adjusted using the external voltage divider network of RENT and
RENB. The UVLO has two thresholds, one for power up when the input voltage is rising and one for power down
or brownouts when the input voltage is falling. 方程式13 can be used to determine the VIN UVLO level.
RENT + RENB
RENB
V
= VENH ì
IN_RISING
(13)
The EN rising threshold (VENH) for the TPS2585x-Q1 is set to be 1.3 V (typical). Choose 10 kΩ for RENB to
minimize input current from the supply. If the desired VIN UVLO level is at 6.0 V, then the value of RENT can be
calculated using 方程式14:
V
≈
’
IN_RISING
RENT
=
-1 ìR
∆
∆
÷
ENB
÷
VENH
«
◊
(14)
方程式 14 yields a value of 36.1 kΩ. The resulting falling UVLO threshold equals 5.5 V and can be calculated by
方程式15, where EN hysteresis (VEN_HYS) is 0.1 V (typical).
RENT + RENB
RENB
V
= VENH - VEN_HYS
(
ì
)
IN_FALLING
(15)
Note that it cannot connect EN to IN pin directly for self-start up. Because the voltage rating of EN pin is 11 V,
tying it to VIN directly damages the device. The simplest way to enable the operation of the TPS2585x-Q1 is to
connect the EN to VSENSE. This connection allows the automatic start up when VIN is within the operation range.
11.2.2.8 Cable Compensation Set-Point
The TPS2585x-Q1 must short the VSET pin to ground to enable the cable compensation. With that setting, the
buck regulator increases its output voltage linearly as the load current increases, and the voltage compensation
at the currents of the USB ports greater than 2.4 A is 90 mV.
Copyright © 2021 Texas Instruments Incorporated
46
Submit Document Feedback
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
11.2.3 Application Curves
Unless otherwise specified the following conditions apply: VIN = 13.5 V, fSW = 2100 kHz, L = 0.68 µH, CSENSE = 66 µF,
CPA_BUS = 1 µF, CPB_BUS = 1 µF, ILIM = GND, TA = 25 °C.
100
95
90
85
80
75
70
65
60
100
95
90
85
80
75
70
65
60
VIN=6V
VIN=13.5V
VIN=18V
VIN=26V
VIN=6V
VIN=13.5V
VIN=18V
0.1
1
6
0.1
1
6
Load Current(A)
Load Current(A)
VSET = GND
fSW = 400 kHz
L = 3.3 uH
VSET = GND
fSW = 2100 kHz
L = 0.68 uH
图11-2. Buck Only Efficiency
图11-3. Buck Only Efficiency
0.4
Level[dBuV]
VIN=6V
VIN=13.5V
VIN=18V
0.2
0
-0.2
-0.4
-0.6
-0.8
-1
PA_BUS = 3A,
PB_BUS = 3A
fSW = 2100 kHz
L = 0.68 uH
-1.2
-1.4
3
0
6
图11-4. 2.1-Mhz EMI Results (Without CM Filter)
Load Current(A)
VSET = GND
fSW = 2100 kHz
图11-5. Load Regulation
Load=2A
0.1
Load=4A
Load=6A
VPA_BUS
200mV/Div
-0.1
-0.3
-0.5
-0.7
-0.9
-1.1
-1.3
-1.5
IPA_BUS
2A/Div
200.0us/Div
5
12
18
26
VSET =
VSENSE
IPA_BUS = 0 A to 3 A
IPB_BUS = 3 A fSW = 2100
kHZ
Input Voltage(V)
VSET = GND
fSW = 2100 kHz
图11-7. Load Transient Without Cable
图11-6. Line Regulation
Compensation
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
47
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
VPB_BUS
200mV/Div
VPA_BUS
200mV/Div
IPB_BUS
2A/Div
IPA_BUS
2A/Div
200.0us/Div
200.0us/Div
VSET =
VSENSE
IPB_BUS = 0 A to 3 A
IPA_BUS = 3 A fSW = 2100
kHZ
VSET =
VSENSE
IPA_BUS = 0.75 A to IPB_BUS = 0 A
2.25 A
fSW = 400
kHZ
图11-8. Load Transient Without Cable
图11-9. Load Transient Without Cable
Compensation
Compensation
VPA_BUS
200mV/Div
VPA_BUS
200mV/Div
IPA_BUS
2A/Div
IPA_BUS
2A/Div
2.0ms/Div
2.0ms/Div
VSET =
GND
IPA_BUS = 0 A to 3 A
IPB_BUS = 3 A fSW = 2100
kHZ
VSET = IPA_BUS = 0.75 A to
GND 2.25 A
IPB_BUS = 0 A fSW = 400
kHZ
图11-10. Load Transient With Cable Compensation
图11-11. Load Transient With Cable Compensation
5.2
Load=2A
Load=4A
SW
5V/Div
5.15
Load=6A
5.1
5.05
VPA_BUS
10mV/Div
5.0
4.95
500.0ns/Div
4.9
5.5
10.5
15.5
20.5
26
VSET = GND IPA_BUS = 3 A IPB_BUS = 3 A fSW = 2100
kHZ
Input Voltage(V)
图11-12. Dropout Characteristic
图11-13. 6-A Output Ripple
Copyright © 2021 Texas Instruments Incorporated
48
Submit Document Feedback
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
SW
5V/Div
SW
5V/Div
VPA_BUS
10mV/Div
VPA_BUS
10mV/Div
500.0ns/Div
500.0ns/Div
VSET =
GND
IPA_BUS = 0.1 A IPB_BUS = 0 A fSW = 2100
kHZ
VSET = GND IPA_BUS = 0 A IPB_BUS = 0 A fSW = 2100
kHZ
图11-14. 100-mA Output Ripple
图11-15. No Load Output Ripple
EN
5V/Div
EN
5V/Div
VIN
5V/Div
VIN
5V/Div
VPA_BUS
5V/Div
VPA_BUS
5V/Div
VSENSE
5V/Div
VSENSE
5V/Div
50ms/Div
20ms/Div
VIN = 0 V to 13.5 V PA_CC1 = Rd
IPA_BUS = 3 A
VIN = 13.5 V to 0 V PA_CC1 = Rd
IPA_BUS = 3 A
图11-16. Startup Relate to VIN
图11-17. Shutdown Relate to VIN
EN
5V/Div
EN
5V/Div
VIN
2V/Div
VIN
5V/Div
VPB_BUS
5V/Div
VPB_BUS
5V/Div
VSENSE
5V/Div
VSENSE
5V/Div
50ms/Div
50ms/Div
EN = 0 V to 5 V
PB_CC1 = Rd
IPB_BUS = 3 A
EN = 5 V to 0 V
PB_CC1 = Rd
IPB_BUS = 3 A
图11-18. Startup Relate to EN
图11-19. Shutdown Relate to EN
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
49
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
VIN
10V/Div
VIN
10V/Div
VPA_BUS
2V/Div
VPA_BUS
2V/Div
VPA_CC1
2V/Div
VPA_CC1
2V/Div
VPA_CC2
2V/Div
VPA_CC2
2V/Div
20ms/Div
50ms/Div
PA_CC1 = Rd to
Open
PA_CC2 = Open
IPA_BUS = 3 A
PA_CC1 = Open to
Rd
PA_CC2 = Open IPA_BUS = 3 A
图11-21. Rd Desert
图11-20. Rd Assert
EN
5V/Div
EN
5V/Div
VPB_BUS
2V/Div
VPB_BUS
2V/Div
VPA_BUS
2V/Div
VPA_BUS
2V/Div
IPA_BUS
5A/Div
IPA_BUS
5A/Div
200.0ms/Div
200.0ms/Div
EN to High
PA_BUS = GND
PB_BUS = GND
图11-23. Short Circuit Recovery
图11-22. Enable Into Short
EN
5V/Div
EN
5V/Div
VPB_BUS
2V/Div
VPB_BUS
2V/Div
VPA_BUS
3V/Div
VPA_BUS
3V/Div
IPA_BUS
3A/Div
IPA_BUS
3A/Div
500.0ms/Div
500.0ms/Div
EN to High
PA_BUS = 1 Ω
PB_BUS = 1 Ω
图11-25. 1-ΩLoad Recovery
图11-24. Enable Into 1-ΩLoad
Copyright © 2021 Texas Instruments Incorporated
50
Submit Document Feedback
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
VPA_CC1
2V/Div
EN
5V/Div
VPA_BUS
3V/Div
VPA_CC2
2V/Div
VPA_BUS
2V/Div
IPA_CC2
200mA/Div
IPA_BUS
5A/Div
2ms/Div
2ms/Div
PA_CC1 = Rd
PA_CC2 = Ra
图11-26. VBUS Hot Short to GND
图11-27. PA_CC2 Hot Short to GND
EN
5V/Div
EN
5V/Div
VOUT
2V/Div
VOUT
2V/Div
VPA_BUS
2V/Div
VPA_BUS
2V/Div
IOUT
500mA/Div
IOUT
500mA/Div
5ms/Div
5ms/Div
PA_CC1 = Rd
PA/B_BUS NO
LOAD
OUT = 5.1 Ω
PA_CC1 = Rd
OUT = GND
PA/B_BUS NO
LOAD
图11-28. OUT short to 5.1-ΩLoad
图11-29. OUT Hot Short to GND
VTS
2V/Div
VTS
2V/Div
VPA_BUS
5V/Div
VPA_BUS
5V/Div
VPA_CC1
2V/Div
VPA_CC1
2V/Div
SW
10V/Div
100.0ms/Div
SW
10V/Div
100.0ms/Div
VTS = 0 V to 4 V
PA_CC1 = Rd
PA_CC2 = OPEN
VTS = 0 V to 2.6 V PA_CC1 = Rd
PA_CC2 = OPEN
图11-31. Thermal Sensing - NTC Temperature HOT
图11-30. Thermal Sensing - NTC Temperature
Behavior
WARM Behavior
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
51
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
12 Power Supply Recommendations
The input supply must be able to withstand the maximum input current and maintain a stable voltage. The
resistance of the input supply rail must be low enough that an input current transient does not cause a high
enough drop at the TPS2585x-Q1 supply voltage that it causes a false UVLO fault triggering and system reset. If
the TPS2585x-Q1 is connected to the input supply through long wires or PCB traces, special care is required to
achieve good performance. An additional bulk capacitance can be required in addition to the ceramic input
capacitors. The amount of bulk capacitance is not critical, but a 100-μF electrolytic capacitor is a typical choice.
The input voltage must not be allowed to fall below the output voltage. In this scenario, such as a shorted input
test, the output capacitors discharge through the internal parasitic diode found between the VIN and SW pins of
the device. During this condition, the current can become uncontrolled, possibly causing damage to the device. If
this scenario is considered likely, then a Schottky diode between the input supply and the output must be used.
13 Layout
13.1 Layout Guidelines
The PCB layout of any bulk converter is critical to the optimal performance of the design. Bad PCB layout can
disrupt the operation of an otherwise good schematic design. Even if the converter regulates correctly, bad PCB
layout can mean the difference between a robust design and one that cannot be mass produced. Furthermore,
the EMI performance of the converter is dependent on the PCB layout to a great extent. The following guidelines
will help users design a PCB with the best power conversion performance, thermal performance, and minimized
generation of unwanted EMI.
1. The input bypass capacitor, CIN, must be placed as close as possible to the IN and PGND pins. The high
frequency ceramic bypass capacitors at the input side provide a primary path for the high di/dt components
of the pulsing current. Use a wide VIN plane on a lower layer to connect both of the VIN pairs together to the
input supply. Grounding for both the input and output capacitors must consist of localized top-side planes
that connect to the PGND pin and PAD.
2. Use ground plane in one of the middle layers as noise shielding and heat dissipation path.
3. Use wide traces for the CBOOT capacitor. Place the CBOOT capacitor as close to the device with short, wide
traces to the BOOT and SW pins.
4. The SW pin connecting to the inductor must be as short as possible, and just wide enough to carry the load
current without excessive heating. Short, thick traces or copper pours (shapes) must be used for a high
current conduction path to minimize parasitic resistance. The output capacitors must be placed close to the
VSENSE end of the inductor and closely grounded to PGND pin and exposed PAD.
5. RILIM and RFREQ resistors must be placed as close as possible to the ILIM and FREQ pins and connected to
AGND. If needed, these components can be placed on the bottom side of the PCB with signals routed
through small vias, and the traces need far away from noisy nets like SW, BOOT.
6. Make VIN, VSENSE, and ground bus connections as wide as possible. This action reduces any voltage drops
on the input or output paths of the converter and maximizes efficiency.
7. Provide enough PCB area for proper heat sinking. Enough copper area must be used to ensure a low RθJA
commensurate with the maximum load current and ambient temperature. Make the top and bottom PCB
layers with two-ounce copper; and no less than one ounce. If the PCB design uses multiple copper layers
(recommended), thermal vias can also be connected to the inner layer heat-spreading ground planes. Note
,
that the package of this device dissipates heat through all pins. Wide traces must be used for all pins except
where noise considerations dictate minimization of area.
8. Use an array of heat-sinking vias to connect the exposed pad to the ground plane on the bottom PCB layer.
If the PCB has multiple copper layers, these thermal vias can also be connected to inner layer heat-
spreading ground planes. Ensure enough copper area is used for heat-sinking to keep the junction
temperature below 150°C.
9. Keep the CC lines close to the same length. Do not create stubs or test points on the CC lines.
Copyright © 2021 Texas Instruments Incorporated
52
Submit Document Feedback
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
13.2 Layout Example
EMI Filter
PGND
BATT
PGND
CIN
CIN
L
VIN
RBOOT
20
19
18
17
16
1
14
13
21
22
CBOOT
RBOOT
12
11
VIN
SW
PB_BUS
SENSE
23
USB
24 PGND
PA_BUS 10
2
3
4
5
6
7
8
9
1
L
VSENSE
PGND
Top Trace/Plane
Inner GND Plane
Top
Inner GND Plane
Signal Layers
VIA to Signal Layer
VIA to GND Planes
VIA to Strap
Power and GND
图13-1. Layout Example
13.3 Ground Plane and Thermal Considerations
TI recommends to use one of the middle layers as a solid ground plane. Ground plane provides shielding for
sensitive circuits and traces. Ground plane also provides a quiet reference potential for the control circuitry. The
AGND and PGND pins must be connected to the ground plane using vias right next to the bypass capacitors.
The PGND pin is connected to the source of the internal low-side MOSFET switch, and also connected directly
to the grounds of the input and output capacitors. The PGND net contains noise at the switching frequency and
can bounce due to load variations. The PGND trace, as well as VIN and SW traces, must be constrained to one
side of the ground plane. The other side of the ground plane contains much less noise and must be used for
sensitive routes.
TI recommends to provide adequate device heat sinking by using the PAD of the IC as the primary thermal path.
Use a minimum 4 × 2 array of 12-mil thermal vias to connect the PAD to the system ground plane heat sink. The
vias must be evenly distributed under the PAD. Use as much copper as possible, for system ground plane, on
the top and bottom layers for the best heat dissipation. Use a four-layer board with the copper thickness for the
four layers, starting from the top of 2 oz / 1 oz / 1 oz / 2 oz. Four layer boards with enough copper thickness
provide low current conduction impedance, proper shielding, and lower thermal resistance.
The thermal characteristics of the TPS2585x-Q1 are specified using the parameter θJA, which characterizes the
junction temperature of silicon to the ambient temperature in a specific system. Although the value of θJA is
dependent on many variables, it still can be used to approximate the operating junction temperature of the
device. To obtain an estimate of the device junction temperature, one can use the following relationship:
TJ = PD × θJA + TA
(16)
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
53
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
where
• TJ = Junction temperature in °C
• PD = VIN × IIN × (1 –Efficiency) –1.1 × IOUT 2 × DCR in Watt
• DCR = Inductor DC parasitic resistance in Ω
• θJA = Junction-to-ambient thermal resistance of the device in °C/W
• TA = Ambient temperature in °C
The maximum operating junction temperature of the TPS2585x-Q1 is 150°C. θJA is highly related to PCB size
and layout, as well as environmental factors such as heat sinking and air flow.
Copyright © 2021 Texas Instruments Incorporated
54
Submit Document Feedback
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
14 Device and Documentation Support
14.1 接收文档更新通知
要接收文档更新通知,请导航至 ti.com 上的器件产品文件夹。点击订阅更新 进行注册,即可每周接收产品信息更
改摘要。有关更改的详细信息,请查看任何已修订文档中包含的修订历史记录。
14.2 支持资源
TI E2E™ 支持论坛是工程师的重要参考资料,可直接从专家获得快速、经过验证的解答和设计帮助。搜索现有解
答或提出自己的问题可获得所需的快速设计帮助。
链接的内容由各个贡献者“按原样”提供。这些内容并不构成 TI 技术规范,并且不一定反映 TI 的观点;请参阅
TI 的《使用条款》。
14.3 Trademarks
HotRod™ and TI E2E™ are trademarks of Texas Instruments.
USB Type-C® is a registered trademark of USB Implementers Forum.
所有商标均为其各自所有者的财产。
14.4 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric changes could cause the device not to meet its published
specifications.
14.5 术语表
TI 术语表
本术语表列出并解释了术语、首字母缩略词和定义。
Copyright © 2021 Texas Instruments Incorporated
Submit Document Feedback
55
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
TPS25850-Q1, TPS25851-Q1, TPS25852-Q1
ZHCSLZ4D –MAY 2020 –REVISED SEPTEMBER 2021
www.ti.com.cn
15 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2021 Texas Instruments Incorporated
56
Submit Document Feedback
Product Folder Links: TPS25850-Q1 TPS25851-Q1 TPS25852-Q1
重要声明和免责声明
TI 提供技术和可靠性数据(包括数据表)、设计资源(包括参考设计)、应用或其他设计建议、网络工具、安全信息和其他资源,不保证没
有瑕疵且不做出任何明示或暗示的担保,包括但不限于对适销性、某特定用途方面的适用性或不侵犯任何第三方知识产权的暗示担保。
这些资源可供使用TI 产品进行设计的熟练开发人员使用。您将自行承担以下全部责任:(1) 针对您的应用选择合适的TI 产品,(2) 设计、验
证并测试您的应用,(3) 确保您的应用满足相应标准以及任何其他安全、安保或其他要求。这些资源如有变更,恕不另行通知。TI 授权您仅可
将这些资源用于研发本资源所述的TI 产品的应用。严禁对这些资源进行其他复制或展示。您无权使用任何其他TI 知识产权或任何第三方知
识产权。您应全额赔偿因在这些资源的使用中对TI 及其代表造成的任何索赔、损害、成本、损失和债务,TI 对此概不负责。
TI 提供的产品受TI 的销售条款(https:www.ti.com/legal/termsofsale.html) 或ti.com 上其他适用条款/TI 产品随附的其他适用条款的约束。TI
提供这些资源并不会扩展或以其他方式更改TI 针对TI 产品发布的适用的担保或担保免责声明。重要声明
邮寄地址:Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2021,德州仪器(TI) 公司
PACKAGE OPTION ADDENDUM
www.ti.com
23-Jun-2023
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
PTPS25850A0QRPQTQ1
TPS25850QRPQRQ1
TPS25851QRPQRQ1
TPS25852QRPQRQ1
ACTIVE
ACTIVE
ACTIVE
ACTIVE
VQFN-HR
VQFN-HR
VQFN-HR
VQFN-HR
RPQ
RPQ
RPQ
RPQ
25
25
25
25
250
TBD
Call TI
Call TI
-40 to 125
-40 to 125
-45 to 125
-45 to 125
Samples
Samples
Samples
Samples
3000 RoHS & Green
3000 RoHS & Green
3000 RoHS & Green
NIPDAU
NIPDAU
NIPDAU
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
T25850
T25851
T25852
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
23-Jun-2023
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Jun-2023
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
K0
P1
W
B0
Reel
Diameter
Cavity
A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
Overall width of the carrier tape
W
P1 Pitch between successive cavity centers
Reel Width (W1)
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Sprocket Holes
Q1 Q2
Q3 Q4
Q1 Q2
Q3 Q4
User Direction of Feed
Pocket Quadrants
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TPS25850QRPQRQ1
TPS25851QRPQRQ1
TPS25852QRPQRQ1
VQFN-
HR
RPQ
RPQ
RPQ
25
25
25
3000
3000
3000
330.0
330.0
330.0
12.4
12.4
12.4
3.8
3.8
3.8
4.8
4.8
4.8
1.18
1.18
1.18
8.0
8.0
8.0
12.0
12.0
12.0
Q1
Q1
Q1
VQFN-
HR
VQFN-
HR
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Jun-2023
TAPE AND REEL BOX DIMENSIONS
Width (mm)
H
W
L
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TPS25850QRPQRQ1
TPS25851QRPQRQ1
TPS25852QRPQRQ1
VQFN-HR
VQFN-HR
VQFN-HR
RPQ
RPQ
RPQ
25
25
25
3000
3000
3000
367.0
367.0
367.0
367.0
367.0
367.0
38.0
38.0
38.0
Pack Materials-Page 2
PACKAGE OUTLINE
RPQ0025A
VQFN - 1 mm max height
S
C
A
L
E
3
.
0
0
0
PLASTIC QUAD FLATPACK - NO LEAD
3.6
3.4
A
B
PIN 1 INDEX AREA
4.6
4.4
SIDE WALL
METAL THICKNESS
DIM A
OPTION 1
0.1
OPTION 2
0.2
C
1.0
0.8
SEATING PLANE
0.08 C
0.05
0.00
1.325 0.1
0.75
0.55
PINS 7,8,14 & 15
0.975
0.775
4X
2X 1
8X (0.25)
10
EXPOSED
THERMAL PAD
SYMM
(DIM A) TYP
12
9
13
1.45
1.25
3X
0.65 0.1
PKG
25
2X 4
0.7
0.5
PINS 3 &19
PIN 1 ID
20X 0.5
0.3
24X
0.2
1
21
24
22
0.1
C A B
1.8
1.6
0.725
0.525
PINS 2 & 20
3X
0.05
0.9
0.7
PINS 4-6 & 16-18
4224966/B 08/2022
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. The package thermal pad must be soldered to the printed circuit board for thermal and mechanical performance.
www.ti.com
EXAMPLE BOARD LAYOUT
RPQ0025A
VQFN - 1 mm max height
PLASTIC QUAD FLATPACK - NO LEAD
(3.1)
(3.05)
(1.325)
4X (1.075)
4X (0.675)
3X
(1.9)
SYMM
24
22
4X (0.575)
21
2X (0.825)
1
4X (0.25)
2X (0.8)
20X (0.5)
6X (1)
(1.5)
PKG
25
(0.65)
(R0.05) TYP
(1.675)
20X (0.25)
4X (0.85)
SEE SOLDER MASK
DETAIL
13
9
10
12
3X
(1.55)
(2.9)
(3.075)
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE: 20X
0.07 MIN
ALL AROUND
0.07 MAX
ALL AROUND
METAL UNDER
SOLDER MASK
METAL EDGE
EXPOSED METAL
SOLDER MASK
OPENING
EXPOSED
METAL
SOLDER MASK
OPENING
NON SOLDER MASK
SOLDER MASK DEFINED
DEFINED
(PREFERRED)
SOLDER MASK DETAILS
4224966/B 08/2022
NOTES: (continued)
4. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature
number SLUA271 (www.ti.com/lit/slua271).
5. Vias are optional depending on application, refer to device data sheet. If any vias are implemented, refer to their locations shown
on this view. It is recommended that vias under paste be filled, plugged or tented.
www.ti.com
EXAMPLE STENCIL DESIGN
RPQ0025A
VQFN - 1 mm max height
PLASTIC QUAD FLATPACK - NO LEAD
(3.1)
(3.05)
4X (1.075)
4X (0.675)
SYMM
6X (0.85)
22
24
4X (0.575)
21
1
2X (0.825)
4X (0.25)
20X (0.5)
2X (0.8)
(2.025)
6X (1)
(0.975)
2X
(0.563)
PKG
25
2X (0.325)
(1.237)
2X (0.65)
26X (0.25)
(2.112)
4X (0.85)
13
9
(R0.05) TYP
10
12
6X
(0.675)
EXPOSED METAL
TYP
(0.763)
(2.9)
(3.075)
SOLDER PASTE EXAMPLE
BASED ON 0.125 MM THICK STENCIL
SCALE: 20X
EXPOSED PAD 25
85% PRINTED SOLDER COVERAGE BY AREA UNDER PACKAGE
4224966/B 08/2022
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
www.ti.com
重要声明和免责声明
TI“按原样”提供技术和可靠性数据(包括数据表)、设计资源(包括参考设计)、应用或其他设计建议、网络工具、安全信息和其他资源,
不保证没有瑕疵且不做出任何明示或暗示的担保,包括但不限于对适销性、某特定用途方面的适用性或不侵犯任何第三方知识产权的暗示担
保。
这些资源可供使用 TI 产品进行设计的熟练开发人员使用。您将自行承担以下全部责任:(1) 针对您的应用选择合适的 TI 产品,(2) 设计、验
证并测试您的应用,(3) 确保您的应用满足相应标准以及任何其他功能安全、信息安全、监管或其他要求。
这些资源如有变更,恕不另行通知。TI 授权您仅可将这些资源用于研发本资源所述的 TI 产品的应用。严禁对这些资源进行其他复制或展示。
您无权使用任何其他 TI 知识产权或任何第三方知识产权。您应全额赔偿因在这些资源的使用中对 TI 及其代表造成的任何索赔、损害、成
本、损失和债务,TI 对此概不负责。
TI 提供的产品受 TI 的销售条款或 ti.com 上其他适用条款/TI 产品随附的其他适用条款的约束。TI 提供这些资源并不会扩展或以其他方式更改
TI 针对 TI 产品发布的适用的担保或担保免责声明。
TI 反对并拒绝您可能提出的任何其他或不同的条款。IMPORTANT NOTICE
邮寄地址:Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023,德州仪器 (TI) 公司
相关型号:
TPS25850QRPQRQ1
具有可编程电流限制和热管理功能的双路 3A USB Type-C 充电端口控制器 | RPQ | 25 | -40 to 125Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS25851-Q1
具有甩负荷和插头极性检测功能的 2.2MHz 双路 3A USB Type-C® 充电端口控制器Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS25851QRPQRQ1
具有甩负荷和插头极性检测功能的 2.2MHz 双路 3A USB Type-C® 充电端口控制器 | RPQ | 25 | -45 to 125Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS25852-Q1
具有 USB 端口开/关控制功能的 2.2MHz 双路 3A USB Type-C® 充电端口控制器Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS25852QRPQRQ1
具有 USB 端口开/关控制功能的 2.2MHz 双路 3A USB Type-C® 充电端口控制器 | RPQ | 25 | -45 to 125Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS25854-Q1
具有甩负荷功能的单路 3A USB Type-C® 充电端口控制器Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS25854QRPQRQ1
具有甩负荷功能的单路 3A USB Type-C® 充电端口控制器 | RPQ | 25 | -45 to 125Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS25855-Q1
具有甩负荷功能的 2.2MHz 单路 3A USB Type-C® 充电端口控制器Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS25855QRPQRQ1
具有甩负荷功能的 2.2MHz 单路 3A USB Type-C® 充电端口控制器 | RPQ | 25 | -45 to 125Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS25858-Q1
TPS25858-Q1 and TPS25859-Q1 Low EMI Dual 3-A USB Type-C® Charging Ports Converter With Programmable Current Limit and Thermal ManagementWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS25858-Q1_V01
TPS25858-Q1 and TPS25859-Q1 Low EMI Dual 3-A USB Type-C® Charging Ports Converter With Programmable Current Limit and Thermal ManagementWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS25858QRPQRQ1
TPS25858-Q1 and TPS25859-Q1 Low EMI Dual 3-A USB Type-C® Charging Ports Converter With Programmable Current Limit and Thermal ManagementWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
©2020 ICPDF网 联系我们和版权申明