TPS61258YFF [TI]
3.5-MHz HIGH EFFICIENCY STEP-UP CONVERTER IN CHIP SCALE PACKAGING; 3.5 MHz的高效率,升压型转换器,芯片级封装型号: | TPS61258YFF |
厂家: | TEXAS INSTRUMENTS |
描述: | 3.5-MHz HIGH EFFICIENCY STEP-UP CONVERTER IN CHIP SCALE PACKAGING |
文件: | 总34页 (文件大小:6073K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TPS61253, TPS61254, TPS61256, TPS61258
www.ti.com
SLVSAG8B –SEPTEMBER 2011–REVISED MAY 2012
3.5-MHz HIGH EFFICIENCY STEP-UP CONVERTER IN CHIP SCALE PACKAGING
Check for Samples: TPS61253, TPS61254, TPS61256, TPS61258
1
FEATURES
DESCRIPTION
•
•
•
•
•
•
•
•
•
•
•
93% Efficiency at 3.5MHz Operation
22µA Quiescent Current in Standby Mode
36µA Quiescent Current in Normal Operation
Wide VIN Range From 2.3V to 5.5V
The TPS6125x device provides a power supply
solution for battery-powered portable applications.
Intended for low-power applications, the TPS6125x
supports up to 800-mA load current from a battery
discharged as low as 2.65V and allows the use of low
cost chip inductor and capacitors.
VIN ≥ VOUT Operation
IOUT ≥800mA at VOUT = 4.5V, VIN ≥2.65V
IOUT ≥1000mA at VOUT = 5.0V, VIN ≥3.3V
IOUT ≥1500mA (Peak) at VOUT = 5.0V, VIN ≥3.3V
With a wide input voltage range of 2.3V to 5.5V, the
device supports applications powered by Li-Ion
batteries with extended voltage range. Different fixed
voltage output versions are available from 3.15V to
5.0V.
±2% Total DC Voltage Accuracy
Light-Load PFM Mode
The TPS6125x operates at a regulated 3.5-MHz
switching frequency and enters power-save mode
operation at light load currents to maintain high
efficiency over the entire load current range. The
PFM mode extends the battery life by reducing the
quiescent current to 36μA (typ) during light load
operation.
Selectable Standby Mode or True Load
Disconnect During Shutdown
•
•
Thermal Shutdown and Overload Protection
Only Three Surface-Mount External
Components Required
Total Solution Size <25mm2
9-Pin NanoFreeTM (CSP) Packaging
•
•
In addition, the TPS6125x device can also maintain
its output biased at the input voltage level. In this
mode, the synchronous rectifier is current limited
allowing external load (e.g. audio amplifier) to be
powered with a restricted supply. In this mode, the
quiescent current is reduced to 22µA. Input current in
shutdown mode is less than 1µA (typ), which
maximizes battery life.
APPLICATIONS
•
•
•
Cell Phones, Smart-Phones
Mono and Stereo APA Applications
USB Charging Port (5V)
The TPS6125x offers a very small solution size due
to minimum amount of external components. It allows
the use of small inductors and input capacitors to
achieve a small solution size. During shutdown, the
load is completely disconnected from the battery.
spacer
spacer
VO = 5.0 V
100
90
80
70
60
50
40
30
20
VOUT
5.0 V @ 700mA
TPS61256
L
SW
VIN
EN
VOUT
BP
VIN
2.65 V .. 4.85 V
1 μH
CO
10 uF
CI
4.7 μF
.
GND
10
0
Figure 2. Smallest Solution Size Application
Figure 1. Efficiency vs. Load Current
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
UNLESS OTHERWISE NOTED this document contains
PRODUCTION DATA information current as of publication date.
Products conform to specifications per the terms of Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2011–2012, Texas Instruments Incorporated
TPS61253, TPS61254, TPS61256, TPS61258
SLVSAG8B –SEPTEMBER 2011–REVISED MAY 2012
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
AVAILABLE DEVICE OPTION
PACKAGE
MARKING
CHIP CODE
OUTPUT
VOLTAGE
DEVICE
SPECIFIC FEATURES
TA
PART NUMBER(1)
ORDERING(2)
Supports 5V, up to 1500mA peak loading
down to 3.3V input voltage
TPS61253
5.0V
TPS61253YFF
SBF
Supports 4.5V/800mA loading
down to 2.65V input voltage
TPS61254
TPS61255(3)
TPS61256
4.5V
3.75V
5.0V
4.3V
4.5V
TPS61254YFF
TPS61255YFF
TPS61256YFF
TPS61257YFF
TPS61258YFF
QWR
QWS
RAV
RAO
SAZ
Supports 5V/900mA loading
down to 3.3V input voltage
–40°C to 85°C
TPS61257(3)
TPS61258
Supports 4.5V, up to 1500mA peak loading
down to 3.3V input voltage
Supports 5.1V, up to 1500mA peak loading
down to 3.3V input voltage
TPS61259(3)
5.1V
TPS61259YFF
SAY
(1) For detailed ordering information please check the PACKAGE OPTION ADDENDUM section at the end of this datasheet.
(2) The YFF package is available in tape and reel. Add a R suffix (e.g. TPS61254YFFR) to order quantities of 3000 parts. Add a T suffix
(e.g. TPS61254YFFT) to order quantities of 250 parts.
(3) Product preview.Contact TI factory for more information
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range (unless otherwise noted)(1)
UNIT
Input voltage
Voltage at VIN(2), VOUT(2), SW(2), EN(2), BP(2)
–0.3 to 7
1.8
V
A
A
(3)
Continuous average current into SW
Input current
(4)
Peak current into SW
3.5
Power dissipation
Internally limited
(5)
Operationg temperature range, TA
–40 to 85
–40 to 150
–65 to 150
2000
°C
°C
°C
V
Temperature range
ESD rating(6)
Operating virtual junction, TJ
Storage temperature range, Tstg
Human Body Model - (HBM)
Charge Device Model - (CDM)
Machine Model - (MM)
1000
V
200
V
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods my affect device reliability.
(2) All voltages are with respect to network ground terminal.
(3) Limit the junction temperature to 105°C for continuous operation at maximum output power.
(4) Limit the junction temperature to 125°C for 5% duty cycle operation.
(5) In applications where high power dissipation and/or poor package thermal resistance is present, the maximum ambient temperature may
have to be derated. Maximum ambient temperature (TA(max)) is dependent on the maximum operating junction temperature (TJ(max)), the
maximum power dissipation of the device in the application (PD(max)), and the junction-to-ambient thermal resistance of the part/package
in the application (θJA), as given by the following equation: TA(max)= TJ(max)–(θJA X PD(max)). To achieve optimum performance, it is
recommended to operate the device with a maximum junction temperature of 105°C.
(6) The human body model is a 100-pF capacitor discharged through a 1.5-kΩ resistor into each pin. The machine model is a 200-pF
capacitor discharged directly into each pin.
2
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Link(s): TPS61253 TPS61254 TPS61256 TPS61258
TPS61253, TPS61254, TPS61256, TPS61258
www.ti.com
SLVSAG8B –SEPTEMBER 2011–REVISED MAY 2012
RECOMMENDED OPERATING CONDITIONS
MIN
2.65(1)
2.5
NOM
MAX UNIT
4.85
TPS61253
TPS61254
TPS61256
TPS61257
TPS61258
TPS61259
TPS6125X
4.35
2.5
4.85
V
VI
Input voltage range
2.5
4.15
2.65(1)
2.65(1)
55
4.35
4.85
Ω
RL
L
Minimum resistive load for start-up
Inductance
0.7
1.0
5
2.9
50
µH
µF
°C
°C
CO
TA
TJ
Output capacitance
3.5
Ambient temperature
–40
85
Operating junction temperature
–40
125
(1) Up to 1000mA peak output current.
THERMAL INFORMATION
TPS6125x
THERMAL METRIC(1)
YFF
9 PINS
110
UNIT
θJA
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
θJCtop
θJB
35
50
°C/W
ψJT
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
ψJB
θJCbot
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
ELECTRICAL CHARACTERISTICS
Minimum and maximum values are at VIN = 2.3V to 5.5V, VOUT = 4.5V (or VIN, whichever is higher), EN = 1.8V, TA = –40°C to
85°C; Circuit of Parameter Measurement Information section (unless otherwise noted). Typical values are at VIN = 3.6V, VOUT
= 4.5V, EN = 1.8V, TA = 25°C (unless otherwise noted).
PARAMETER
TEST CONDITIONS
MIN
TYP MAX
UNIT
SUPPLY CURRENT
Operating quiescent current
into VIN
30
45
µA
IOUT = 0mA, VIN = 3.6V
EN = VIN, BP = GND
Device not switching
Operating quiescent current
into VOUT
7
11
15
20
15
µA
µA
µA
IQ
TPS6125x
Standby mode quiescent current
into VIN
IOUT = 0mA, VIN = VOUT = 3.6V
EN = GND, BP = VIN
Device not switching
Standby mode quiescent current
into VOUT
9.5
ISD
Shutdown current
TPS6125x
TPS6125x
EN = GND, BP = GND
Falling
0.85
2.0
5.0
2.1
μA
V
VUVLO
Under-voltage lockout threshold
Hysteresis
0.1
V
Copyright © 2011–2012, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Link(s): TPS61253 TPS61254 TPS61256 TPS61258
TPS61253, TPS61254, TPS61256, TPS61258
SLVSAG8B –SEPTEMBER 2011–REVISED MAY 2012
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
Minimum and maximum values are at VIN = 2.3V to 5.5V, VOUT = 4.5V (or VIN, whichever is higher), EN = 1.8V, TA = –40°C to
85°C; Circuit of Parameter Measurement Information section (unless otherwise noted). Typical values are at VIN = 3.6V, VOUT
= 4.5V, EN = 1.8V, TA = 25°C (unless otherwise noted).
PARAMETER
TEST CONDITIONS
MIN
TYP MAX
UNIT
ENABLE, BYPASS
VIL
Low-level input voltage
High-level input voltage
Input leakage current
0.4
0.5
V
V
VIH
TPS6125x
TPS61253
1.0
Ilkg
Input connected to GND or VIN
µA
OUTPUT
2.3V ≤ VIN ≤ 4.85V, IOUT = 0mA
PWM operation. Open Loop
4.92
4.85
5
5
5.08
5.2
3.3V ≤ VIN ≤ 4.85V, 0mA ≤ IOUT ≤ 1000mA
PFM/PWM operation
Regulated DC output voltage
V
3.3V ≤ VIN ≤ 4.85V, 0mA ≤ IOUT ≤ 1500mA
PFM/PWM operation
Pulsed load test; Pulse width ≤ 20ms;
Duty cycle ≤ 10%
4.75
5
5.2
2.3V ≤ VIN ≤ 4.35V, IOUT = 0mA
PWM operation. Open Loop
4.43
4.4
4.5 4.57
4.5 4.65
Regulated DC output voltage
Regulated DC output voltage
Regulated DC output voltage
TPS61254
TPS61256
TPS61257
V
V
V
2.65V ≤ VIN ≤ 4.35V, 0mA ≤ IOUT ≤ 800mA
PFM/PWM operation
2.3V ≤ VIN ≤ 4.85V, IOUT = 0mA
PWM operation. Open Loop
4.92
4.9
5
5
5.08
5.2
2.65V ≤ VIN ≤ 4.85V, 0mA ≤ IOUT ≤ 700mA
PFM/PWM operation
VOUT
2.3V ≤ VIN ≤ 4.15V, IOUT = 0mA
PWM operation. Open loop.
4.23
4.2
4.3 4.37
4.3 4.45
4.5 4.57
2.65V ≤ VIN ≤ 4.15V, 0mA ≤ IOUT ≤ 800mA
PFM/PWM operation
2.3V ≤ VIN ≤ 4.35V, IOUT = 0mA
PWM operation. Open Loop
4.43
3.3V ≤ VIN ≤ 4.35V, 0mA ≤ IOUT ≤ 1500mA
PFM/PWM operation
Pulsed load test; Pulse width ≤ 20ms;
Duty cycle ≤ 10%
Regulated DC output voltage
Regulated DC output voltage
TPS61258
TPS61259
V
V
4.3
5.02
4.75
4.5 4.65
5.1 5.18
2.3V ≤ VIN ≤ 4.85V, IOUT = 0mA
PWM operation. Open Loop
3.3V ≤ VIN ≤ 4.85V, 0mA ≤ IOUT ≤ 1500mA
PFM/PWM operation
Pulsed load test; Pulse width ≤ 20ms;
Duty cycle ≤ 10%
5.1
45
5.3
Power-save mode output ripple
voltage
PFM operation, IOUT = 1mA
TPS61254
TPS61258
Standby mode output ripple
voltage
mVpk
mVpk
EN = GND, BP = VIN, IOUT = 0mA
PWM operation, IOUT = 200mA
PFM operation, IOUT = 1mA
80
20
50
PWM mode output ripple voltage
ΔVOUT
Power-save mode output ripple
voltage
TPS61253
TPS61256
TPS61259
Standby mode output ripple
voltage
EN = GND, BP = VIN, IOUT = 0mA
PWM operation, IOUT = 200mA
80
20
PWM mode output ripple voltage
4
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Link(s): TPS61253 TPS61254 TPS61256 TPS61258
TPS61253, TPS61254, TPS61256, TPS61258
www.ti.com
SLVSAG8B –SEPTEMBER 2011–REVISED MAY 2012
ELECTRICAL CHARACTERISTICS (continued)
Minimum and maximum values are at VIN = 2.3V to 5.5V, VOUT = 4.5V (or VIN, whichever is higher), EN = 1.8V, TA = –40°C to
85°C; Circuit of Parameter Measurement Information section (unless otherwise noted). Typical values are at VIN = 3.6V, VOUT
= 4.5V, EN = 1.8V, TA = 25°C (unless otherwise noted).
PARAMETER
TEST CONDITIONS
MIN
TYP MAX
UNIT
POWER SWITCH
High-side MOSFET on resistance
Low-side MOSFET on resistance
170
100
rDS(on)
Ilkg
TPS6125x
mΩ
Reverse leakage current into
VOUT
TPS6125x
TPS61253
EN = GND, BP = GND
3.5
µA
EN = VIN, BP = GND. Open Loop
3300
3620 3900
TPS61258
TPS61259
Switch valley current limit
mA
TPS61254
TPS61256
TPS61257
ILIM
EN = VIN, BP = GND. Open Loop
EN = GND, BP = VIN
1900
165
2150 2400
Pre-charge mode current limit
(linear mode)
TPS6125x
TPS6125x
215
265
mA
Overtemperature protection
Overtemperature hysteresis
140
20
°C
°C
OSCILLATOR
fOSC
Oscillator frequency
TPS6125x
TPS6125x
VIN = 3.6V VOUT = 4.5V
3.5
70
MHz
µs
TIMING
BP = GND, IOUT = 0mA.
Time from active EN to start switching
TPS61253
TPS61254
TPS61256
TPS61258
TPS61259
Start-up time
BP = GND, IOUT = 0mA.
Time from active EN to VOUT
400
µs
Copyright © 2011–2012, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Link(s): TPS61253 TPS61254 TPS61256 TPS61258
TPS61253, TPS61254, TPS61256, TPS61258
SLVSAG8B –SEPTEMBER 2011–REVISED MAY 2012
PIN ASSIGNMENTS
TOP VIEW
www.ti.com
BOTTOM VIEW
A3 A2 A1
B3 B2 B1
C3 C2 C1
A1 A2 A3
B1 B2 B3
C1 C2 C3
Table 1. TERMINAL FUNCTIONS
TERMINAL
I/O
DESCRIPTION
NAME
NO.
This is the mode selection pin of the device and is only of relevance when the device is disabled
(EN = Low). This pin must not be left floating and must be terminated. Refer to Table 3 for more
details.
BP
C3
I
BP = Low: The device is in true shutdown mode.
BP = High: The output is biased at the input voltage level with a maximum load current capability of
ca. 150mA. In standby mode, the device only consumes a standby current of 22µA (typ).
This is the enable pin of the device. Connecting this pin to ground forces the device into shutdown
mode. Pulling this pin high enables the device. This pin must not be left floating and must be
terminated.
EN
B3
I
GND
SW
C1, C2
B1, B2
A3
Ground pin.
I/O
I
This is the switch pin of the converter and is connected to the drain of the internal Power MOSFETs.
VIN
Power supply input.
VOUT
A1, A2
O
Boost converter output.
FUNCTIONAL BLOCK DIAGRAM
SW
VOUT
PMOS
NMOS
VIN
Valley
Current
Sense
Modulator
Softstart
VREF
Thermal
Shutdown
EN
BP
Control
Logic
Undervoltage
Lockout
GND
6
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Link(s): TPS61253 TPS61254 TPS61256 TPS61258
TPS61253, TPS61254, TPS61256, TPS61258
www.ti.com
SLVSAG8B –SEPTEMBER 2011–REVISED MAY 2012
PARAMETER MEASUREMENT INFORMATION
TPS6125x
SW
L
VOUT
BP
VOUT
1 μH
VIN
EN
VIN
CO
10 uF
CI
4.7 μF
GND
EN
0
BP
0
Shutdown, True Load Disconnect (SD)
Standby Mode, Output Pre-Biased (SM)
Boost Operating Mode (BST)
0
1
1
X
Table 2. List of Components
REFERENCE
DESCRIPTION
PART NUMBER, MANUFACTURER
LQM32PN1R0MG0, muRata
DFE322512C, TOKO
L(1)
L(2)
CI
1.0μH, 1.8A, 48mΩ, 3.2 x 2.5 x 1.0mm max. height
1.0μH, 3.7A, 37mΩ, 3.2 x 2.5 x 1.2mm max. height
4.7μF, 6.3V, 0402, X5R ceramic
GRM155R60J475M, muRata
GRM188R60J106ME84, muRata
CO
10μF, 6.3V, 0603, X5R ceramic
(1) Inductor used to characterize TPS61254YFF, TPS61255YFF, TPS61256YFF and TPS61257YFF devices.
(2) Inductor used to characterize TPS61253YFF, TPS61258YFF and TPS61259YFF devices.
Copyright © 2011–2012, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Link(s): TPS61253 TPS61254 TPS61256 TPS61258
TPS61253, TPS61254, TPS61256, TPS61258
SLVSAG8B –SEPTEMBER 2011–REVISED MAY 2012
www.ti.com
TYPICAL CHARACTERISTICS
TABLE OF GRAPHS
FIGURE
vs Output current
vs Input voltage
3, 4, 5, 7
η
Efficiency
6
vs Output current
vs Input voltage
8, 9, 10, 11, 12, 16
VO
DC output voltage
13
14, 15
17, 18, 19
20, 21
22, 23
24, 25
26
IO
Maximum output current
Peak-to-peak output ripple voltage
Supply current
vs Input voltage
ΔVO
ICC
vs Output current
vs Input voltage
DC pre-charge current
Valley current limit
vs Differential input-output voltage
vs Temperature
ILIM
rDS(on)
MOSFET rDS(on)
vs Temperature
PFM operation
27
PWM operation
28
Combined line/load transient response
Load transient response
AC load transient response
Start-up
29
30, 32
31, 33
34, 35
EFFICIENCY
vs
EFFICIENCY
vs
OUTPUT CURRENT
OUTPUT CURRENT
100
100
V = 4.5 V
V
= 5 V (TPS61256)
I
O
PFM/PWM Operation
V = 4.5 V
I
95
90
85
80
75
70
65
60
95
90
85
80
75
70
65
60
55
50
V = 3.3 V
I
V = 3.6 V
I
V = 3 V
I
V = 3.6 V
V = 2.7 V
I
I
V = 3.3 V
I
V = 3 V
I
V = 2.7 V
I
V = 2.5 V
I
V = 2.5 V
I
VO = 4.5 V
55
50
PFM/PWM Operation
0.1
1
10
100
0.1
1
10 100
1000
1000
I
- Output Current - mA
I
- Output Current - mA
O
O
Figure 3.
Figure 4.
8
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Link(s): TPS61253 TPS61254 TPS61256 TPS61258
TPS61253, TPS61254, TPS61256, TPS61258
www.ti.com
SLVSAG8B –SEPTEMBER 2011–REVISED MAY 2012
EFFICIENCY
vs
EFFICIENCY
vs
OUTPUT CURRENT
INPUT VOLTAGE
100
95
90
85
80
75
70
65
60
55
100
98
96
94
92
90
88
86
84
82
80
78
76
74
VI = 4.5 V
V
= 5 V
O
PFM/PWM Operation
VI = 4.2 V
I
= 300 mA
O
VI = 3.6 V
VI = 3.3 V
I
= 10 mA
O
I
= 100 mA
O
I
= 800 mA
O
VO = 5 V (TPS61253),
IO = Pulse Operation (tpulse = 20 ms, d = 10%),
72
70
PFM/PWM Operation
50
0
1
10
100
1000
10000
2.5 2.7 2.9 3.1 3.3 3.5 3.7 3.9 4.1 4.3 4.5 4.7 4.9 5.1 5.3 5.5
V - Input Voltage - V
I
IO - Output Current - mA
Figure 5.
Figure 6.
EFFICIENCY
vs
DC OUTPUT VOLTAGE
vs
OUTPUT CURRENT
OUTPUT CURRENT
4.59
100
90
80
70
60
50
40
30
20
10
V = 2.7 V
I
V = 4.5 V
I
V = 3.3 V
I
V = 3 V
I
4.55
4.50
4.46
4.41
V = 3.6 V
I
V = 4.5 V
I
V = 2.5 V
I
V = 3.6 V
I
V
= 4.5 V
O
PFM/PWM Operation
V
~ V
I
Standby Operation
O
0
0.01
0.1
1
10
0.1
1
10
I - Output Current - mA
O
100
100
1000
I
- Output Current - mA
O
Figure 7.
Figure 8.
Copyright © 2011–2012, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Link(s): TPS61253 TPS61254 TPS61256 TPS61258
TPS61253, TPS61254, TPS61256, TPS61258
SLVSAG8B –SEPTEMBER 2011–REVISED MAY 2012
www.ti.com
DC OUTPUT VOLTAGE
vs
DC OUTPUT VOLTAGE
vs
OUTPUT CURRENT
OUTPUT CURRENT
4.545
4.5
5.15
V
= 5 V (TPS61256)
V
= 4.5 V
O
PFM/PWM Operation
O
PWM Operation
V = 4.5 V
I
5.1
V = 5 V
I
V = 4.5 V
I
V = 2.5 V
I
V = 2.7 V
I
4.455
5.05
V = 3 V
I
V = 3.3 V
I
V = 2.5 V
I
V = 3.6 V
I
V = 3.6 V
I
4.41
5
V = 4.2 V
I
4.365
4.95
500
700
900 1100 1300 1500 1700 1900
0.1
1
10
100
1000
I
- Output Current - mA
O
I
- Output Current - mA
O
Figure 9.
Figure 10.
DC OUTPUT VOLTAGE
vs
DC OUTPUT VOLTAGE
vs
OUTPUT CURRENT
OUTPUT CURRENT
5.1
5.05
VO = 5 V (TPS61253),
V
= 5 V (TPS61256)
O
PWM Operation
IO = Pulse Operation (tpulse = 20 ms, d = 10%),
PWM Operation
V = 3.6 V
I
V = 4.2 V
I
5.05
5
VI = 4.5 V
5
4.95
4.9
V = 4.5 V
I
VI = 4.2 V
V = 2.5 V
I
V = 2.7 V
I
4.95
4.9
VI = 3 V
V = 3 V
I
VI = 3.3 V
V = 3.3 V
I
VI = 3.6 V
4.85
4.8
4.85
4.8
4.75
500
700
900 1100 1300 1500 1700 1900
1000 1100 1200 1300 1400 1500 1600 1700 1800 1900 2000
IO - Output Current - mA
I
- Output Current - mA
O
Figure 11.
Figure 12.
10
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Link(s): TPS61253 TPS61254 TPS61256 TPS61258
TPS61253, TPS61254, TPS61256, TPS61258
www.ti.com
SLVSAG8B –SEPTEMBER 2011–REVISED MAY 2012
DC OUTPUT VOLTAGE
vs
MAXIMUM OUTPUT CURRENT
vs
INPUT VOLTAGE
INPUT VOLTAGE
5.55
5.5
2300
2100
1900
1700
1500
1300
1100
900
V
= 5 V
O
PFM/PWM Operation
V
= 5 V (TPS61256)
O
PWM Operation
5.45
5.4
T
= -40°C
A
I
= 800 mA
O
5.35
5.3
T
= 25°C
A
I
= 500 mA
O
5.25
5.2
T
A
= 85°C
5.15
5.1
I
= 100 mA
O
I
= 10 mA
O
5.05
700
500
5
4.95
2.5 2.7 2.9 3.1 3.3 3.5 3.7 3.9 4.1 4.3 4.5 4.7 4.9 5.1 5.3 5.5
V - Input Voltage - V
I
2.5 2.75
3
3.25 3.5 3.75
4
4.25 4.5 4.75
5
V - Input Voltage - V
I
Figure 13.
Figure 14.
MAXIMUM OUTPUT CURRENT
DC OUTPUT VOLTAGE
vs
vs
INPUT VOLTAGE
OUTPUT CURRENT
3000
5
4.8
4.6
4.4
4.2
4
V
~ V
I
Standby Operation
O
2800
2600
2400
2200
2000
1800
1600
1400
1200
1000
800
V = 4.5 V
I
V = 4.2 V
I
TA = -40 °C
TA = 25 °C
3.8
3.6
3.4
3.2
3
V = 3.6 V
I
V = 3.3 V
I
TA = 65 °C
V = 3 V
I
V = 2.7 V
I
TA = 85 °C
2.8
2.6
2.4
2.2
VO = 5 V (TPS61253),
V = 2.5 V
I
IO = Pulse Operation (tpulse = 20 ms, d = 10%)
PWM Operation
2
0
20 40 60 80 100 120 140 160 180 200 220 240
2.5 2.75
3
3.25 3.5 3.75
4
4.25 4.5 4.75
5
I
- Output Current - mA
VI - Input Voltage - V
O
Figure 15.
Figure 16.
Copyright © 2011–2012, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Link(s): TPS61253 TPS61254 TPS61256 TPS61258
TPS61253, TPS61254, TPS61256, TPS61258
SLVSAG8B –SEPTEMBER 2011–REVISED MAY 2012
www.ti.com
PEAK-TO-PEAK OUTPUT RIPPLE VOLTAGE
PEAK-TO-PEAK OUTPUT RIPPLE VOLTAGE
vs
vs
OUTPUT CURRENT
OUTPUT CURRENT
60
55
50
45
40
35
30
25
20
15
10
60
V
= 5 V (TPS61256)
O
PFM/PWM Operation
V
= 5 V (TPS61256)
O
PFM/PWM Operation
55
50
45
40
35
30
25
20
15
10
V = 2.7 V
I
V = 3.3 V
I
V = 2.7 V
I
V = 3.6 V
I
V = 3.3 V
I
V = 3.6 V
I
V = 4.5 V
I
V = 4.5 V
I
CO = 10μF 6.3V (0603) X5R, muRata GRM188R60J106ME84D
100 200 300 400 500 600 700 800 900 1000
CO = 22μF 10V (1210) X5R, muRata GRM32ER71A226K
100 200 300 400 500 600 700 800 900 1000
5
0
5
0
0
0
I
- Output Current - mA
I
- Output Current - mA
O
O
Figure 17.
Figure 18.
PEAK-TO-PEAK OUTPUT RIPPLE VOLTAGE
SUPPLY CURRENT
vs
vs
OUTPUT CURRENT
INPUT VOLTAGE
60
80
75
70
65
60
55
50
45
40
35
30
25
V
= 5 V (TPS61253)
O
PFM/PWM Operation
V
I
= 5 V
O
55
50
45
40
35
30
25
20
15
10
= 0 mA
O
T
= 85°C
A
V = 3.3 V
I
T
= 25°C
A
V = 3.6 V
I
V = 4.5 V
I
T
= -40°C
A
CO = x2 10 mF 6.3 V (0603) X5R,
muRata GRM188R60J106ME84D
5
0
20
15
0
200
400
600
800 1000 1200 1400
2.5 2.7 2.9 3.1 3.3 3.5 3.7 3.9 4.1 4.3 4.5 4.7 4.9
V - Input Voltage - V
I
I
- Output Current - mA
O
Figure 19.
Figure 20.
12
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Link(s): TPS61253 TPS61254 TPS61256 TPS61258
TPS61253, TPS61254, TPS61256, TPS61258
www.ti.com
SLVSAG8B –SEPTEMBER 2011–REVISED MAY 2012
SUPPLY CURRENT
vs
DC PRE-CHARGE CURRENT
vs
INPUT VOLTAGE
DIFFERENTIAL INPUT-OUTPUT VOLTAGE
45
250
V ~ V
245
240
235
230
225
220
215
210
205
200
195
190
185
180
175
170
165
160
I
O
= 0 mA
I
40
35
30
25
20
15
10
O
Standby Operation
T
= -40°C
A
T
= 25°C
A
V = 2.7 V,
I
T
= 85°C
A
T
= 25°C
A
V = 4.5 V,
I
T
= 25°C
A
V = 3.6 V,
I
T
= 25°C
A
5
0
155
150
2.5 2.7 2.9 3.1 3.3 3.5 3.7 3.9 4.1 4.3 4.5 4.7 4.9 5.1 5.3 5.5
V - Input Voltage - V
I
0 0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3 3.3 3.6 3.9 4.2 4.5
Differential Input - Output Voltage - V
Figure 21.
Figure 22.
DC PRE-CHARGE CURRENT
vs
DIFFERENTIAL INPUT-OUTPUT VOLTAGE
VALLEY CURRENT LIMIT
250
25
Sample Size = 200
245
240
235
230
225
220
215
210
205
200
195
190
185
180
175
170
165
160
V
= 3.6 V
IN
T
= 130°C
J
20
15
10
T
J
= 25°C
V = 3.6 V,
I
V = 3.6 V,
T
= 25°C
I
A
T
= 85°C
T
= -20°C
A
J
V = 3.6 V,
I
T
= -40°C
A
5
0
155
150
0
0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7 3
Differential Input - Output Voltage - V
3.3 3.6
I
- Valley Current Limit - mA
LIM
Figure 23.
Figure 24.
Copyright © 2011–2012, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Link(s): TPS61253 TPS61254 TPS61256 TPS61258
TPS61253, TPS61254, TPS61256, TPS61258
SLVSAG8B –SEPTEMBER 2011–REVISED MAY 2012
www.ti.com
MOSFET rDS(on)
vs
VALLEY CURRENT LIMIT
TEMPERATURE
25
200
180
160
140
120
100
80
TPS61253
VIN = 3.6 V,
V
= 5 V
O
Sample Size = 200
TJ = 125°C
20
Rectifier MOSFET
TJ = 25°C
15
TJ = -20°C
Switch MOSFET
10
60
5
0
40
20
0
-30
-10
10
30
50
70
90
110 130
T
- Junction Temperature - °C
J
ILIM - Valley Current Limit - mA
Figure 25.
Figure 26.
POWER-SAVE MODE OPERATION
PWM OPERATION
V = 3.6 V,
I
V = 3.6 V,
I
V
I
= 5.0 V,
O
V
I
= 5.0 V,
O
= 40 mA
O
= 200 mA
O
Figure 27.
Figure 28.
14
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Link(s): TPS61253 TPS61254 TPS61256 TPS61258
TPS61253, TPS61254, TPS61256, TPS61258
www.ti.com
SLVSAG8B –SEPTEMBER 2011–REVISED MAY 2012
LOAD TRANSIENT RESPONSE IN
PFM/PWM OPERATION
COMBINED LINE/LOAD TRANSIENT RESPONSE
V
= 5.0 V
V = 3.6 V,
I
O
V
= 5.0 V
O
50 to 500 mA Load Step
50mA to 500mA
Load Step
3.3V to 3.9V Line Step
Figure 29.
Figure 30.
LOAD TRANSIENT RESPONSE IN
PFM/PWM OPERATION
AC LOAD TRANSIENT RESPONSE
0 to 400mA Load Sweep
V = 3.6 V,
V = 3.6 V,
I
I
V
= 5.0 V
50 to 500 mA Load Step
V
= 5.0 V
O
O
CO = 22μF 10V (1210) X5R, muRata
Figure 31.
Figure 32.
Copyright © 2011–2012, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Link(s): TPS61253 TPS61254 TPS61256 TPS61258
TPS61253, TPS61254, TPS61256, TPS61258
SLVSAG8B –SEPTEMBER 2011–REVISED MAY 2012
www.ti.com
AC LOAD TRANSIENT RESPONSE
START-UP
V = 3.6 V,
I
0 to 400mA Load
V
= 5.0
O
V = 3.6 V,
I
V
I
= 5.0 V,
O
= 0 mA
O
CO = 22μF 10V (1210) X5R, muRata
Figure 33.
Figure 34.
START-UP
V = 2.7 V
I
V = 4.5 V
I
V = 3.6 V
I
V
I
= 5.0 V,
O
= 0 mA
O
Figure 35.
16
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Link(s): TPS61253 TPS61254 TPS61256 TPS61258
TPS61253, TPS61254, TPS61256, TPS61258
www.ti.com
SLVSAG8B –SEPTEMBER 2011–REVISED MAY 2012
DETAILED DESCRIPTION
OPERATION
The TPS6125x synchronous step-up converter typically operates at a quasi-constant 3.5-MHz frequency pulse
width modulation (PWM) at moderate to heavy load currents. At light load currents, the TPS6125x converter
operates in power-save mode with pulse frequency modulation (PFM).
During PWM operation, the converter uses a novel quasi-constant on-time valley current mode control scheme to
achieve excellent line/load regulation and allows the use of a small ceramic inductor and capacitors. Based on
the VIN/VOUT ratio, a simple circuit predicts the required on-time.
At the beginning of the switching cycle, the low-side N-MOS switch is turned-on and the inductor current ramps
up to a peak current that is defined by the on-time and the inductance. In the second phase, once the on-timer
has expired, the rectifier is turned-on and the inductor current decays to a preset valley current threshold. Finally,
the switching cycle repeats by setting the on timer again and activating the low-side N-MOS switch.
In general, a dc/dc step-up converter can only operate in "true" boost mode, i.e. the output “boosted” by a certain
amount above the input voltage. The TPS6125x device operates differently as it can smoothly transition in and
out of zero duty cycle operation. Therefore the output can be kept as close as possible to its regulation limits
even though the converter is subject to an input voltage that tends to be excessive. In this operation mode, the
output current capability of the regulator is limited to ca. 150mA. Refer to the typical characteristics section (DC
Output Voltage vs. Input Voltage) for further details.
The current mode architecture with adaptive slope compensation provides excellent transient load response,
requiring minimal output filtering. Internal soft-start and loop compensation simplifies the design process while
minimizing the number of external components.
POWER-SAVE MODE
The TPS6125X integrates a power-save mode to improve efficiency at light load. In power save mode the
converter only operates when the output voltage trips below a set threshold voltage.
It ramps up the output voltage with several pulses and goes into power save mode once the output voltage
exceeds the set threshold voltage.
The PFM mode is left and PWM mode entered in case the output current can not longer be supported in PFM
mode.
Copyright © 2011–2012, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Link(s): TPS61253 TPS61254 TPS61256 TPS61258
TPS61253, TPS61254, TPS61256, TPS61258
SLVSAG8B –SEPTEMBER 2011–REVISED MAY 2012
www.ti.com
STANDBY MODE
The TPS6125x device is able to maintain its output biased at the input voltage level. In so called standby mode
(EN = 0, BP = 1), the synchronous rectifier is current limited to ca. 150mA allowing an external load (e.g. audio
amplifier) to be powered with a restricted supply. The output voltage is slightly reduced due to voltage drop
across the rectifier MOSFET and the inductor DC resistance. The device consumes only a standby current of
22µA (typ).
Table 3. Operating Mode Control
OPERATING MODE
EN
0
BP
0
Shutdown, True Load Disconnect (SD)
Standby Mode, Output Pre-Biased (SM)
0
1
1
0
Boost Operating Mode (BST)
1
1
CURRENT LIMIT OPERATION
The TPS6125x device employs a valley current limit sensing scheme. Current limit detection occurs during the
off-time by sensing of the voltage drop across the synchronous rectifier.
The output voltage is reduced as the power stage of the device operates in a constant current mode. The
maximum continuous output current (IOUT(CL)), before entering current limit (CL) operation, can be defined by
Equation 1.
1
IOUT(CL) = (1- D) g (IVALLEY
+
DIL )
2
(1)
The duty cycle (D) can be estimated by Equation 2
g h
D = 1-
V
IN
VOUT
(2)
(3)
and the peak-to-peak current ripple (ΔIL) is calculated by Equation 3
V
D
f
IN
DIL =
g
L
The output current, IOUT(DC), is the average of the rectifier ripple current waveform. When the load current is
increased such that the lower peak is above the current limit threshold, the off-time is increased to allow the
current to decrease to this threshold before the next on-time begins (so called frequency fold-back mechanism).
When the current limit is reached the output voltage decreases during further load increase.
Figure 36 illustrates the inductor and rectifier current waveforms during current limit operation.
I
PEAK
I
L
Current Limit
Threshold
I
= I
LIM
VALLEY
Rectifier
Current
I
DI
OUT(CL)
L
I
OUT(DC)
Increased
Load Current
I
IN(DC)
f
Inductorr
Current
I
IN(DC)
DI
L
V
D
f
IN
×
ΔI
=
L
L
Figure 36. Inductor/Rectifier Currents in Current Limit Operation
18
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Link(s): TPS61253 TPS61254 TPS61256 TPS61258
TPS61253, TPS61254, TPS61256, TPS61258
www.ti.com
SLVSAG8B –SEPTEMBER 2011–REVISED MAY 2012
ENABLE
The TPS6125x device starts operation when EN is set high and starts up with the soft-start sequence. For proper
operation, the EN pin must be terminated and must not be left floating.
Pulling the EN and BP pins low forces the device in shutdown, with a shutdown current of typically 1µA. In this
mode, true load disconnect between the battery and load prevents current flow from VIN to VOUT, as well as
reverse flow from VOUT to VIN.
Pulling the EN pin low and the BP pin high forces the device in standby mode, refer to the STANDBY MODE
section for more details.
LOAD DISCONNECT AND REVERSE CURRENT PROTECTION
Regular boost converters do not disconnect the load from the input supply and therefore a connected battery will
be discharge during shutdown. The advantage of TPS6125x is that this converter is disconnecting the output
from the input of the power supply when it is disabled (so called true shutdown mode). In case of a connected
battery it prevents it from being discharge during shutdown of the converter.
SOFTSTART
The TPS6125x device has an internal softstart circuit that limits the inrush current during start-up. The first step
in the start-up cycle is the pre-charge phase. During pre-charge, the rectifying switch is turned on until the output
capacitor is charged to a value close to the input voltage. The rectifying switch is current limited (approx. 200mA)
during this phase. This mechanism is used to limit the output current under short-circuit condition.
Once the output capacitor has been biased to the input voltage, the converter starts switching. The soft-start
system progressively increases the on-time as a function of the input-to-output voltage ratio. As soon as the
output voltage is reached, the regulation loop takes control and full current operation is permitted.
UNDERVOLTAGE LOCKOUT
The under voltage lockout circuit prevents the device from malfunctioning at low input voltages and the battery
from excessive discharge. It disables the output stage of the converter once the falling VIN trips the under-voltage
lockout threshold VUVLO which is typically 2.0V. The device starts operation once the rising VIN trips VUVLO
threshold plus its hysteresis of 100 mV at typ. 2.1V.
THERMAL REGULATION
The TPS6125x device contains a thermal regulation loop that monitors the die temperature during the pre-charge
phase. If the die temperature rises to high values of about 110 °C, the device automatically reduces the current
to prevent the die temperature from increasing further. Once the die temperature drops about 10 °C below the
threshold, the device will automatically increase the current to the target value. This function also reduces the
current during a short-circuit condition.
THERMAL SHUTDOWN
As soon as the junction temperature, TJ, exceeds 140°C (typ.) the device goes into thermal shutdown. In this
mode, the high-side and low-side MOSFETs are turned-off. When the junction temperature falls below the
thermal shutdown minus its hysteresis, the device continuous the operation.
Copyright © 2011–2012, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Link(s): TPS61253 TPS61254 TPS61256 TPS61258
TPS61253, TPS61254, TPS61256, TPS61258
SLVSAG8B –SEPTEMBER 2011–REVISED MAY 2012
www.ti.com
APPLICATION INFORMATION
INDUCTOR SELECTION
A boost converter normally requires two main passive components for storing energy during the conversion, an
inductor and an output capacitor are required. It is advisable to select an inductor with a saturation current rating
higher than the possible peak current flowing through the power switches.
The inductor peak current varies as a function of the load, the input and output voltages and can be estimated
using Equation 4.
V gD
IOUT
V g h
IN
IN
IL(PEAK)
=
+
with D = 1-
2 g f g L
(1- D) g h
VOUT
(4)
Selecting an inductor with insufficient saturation performance can lead to excessive peak current in the
converter. This could eventually harm the device and reduce it's reliability.
When selecting the inductor, as well as the inductance, parameters of importance are: maximum current rating,
series resistance, and operating temperature. The inductor DC current rating should be greater (by some margin)
than the maximum input average current, refer to Equation 5 and CURRENT LIMIT OPERATION section for
more details.
VOUT
1
IL(DC)
=
g
g IOUT
V
h
IN
(5)
The TPS6125x series of step-up converters have been optimized to operate with a effective inductance in the
range of 0.7µH to 2.9µH and with output capacitors in the range of 10µF to 47µF. The internal compensation is
optimized for an output filter of L = 1µH and CO = 10µF. Larger or smaller inductor values can be used to
optimize the performance of the device for specific operating conditions. For more details, see the CHECKING
LOOP STABILITY section.
In high-frequency converter applications, the efficiency is essentially affected by the inductor AC resistance (i.e.
quality factor) and to a smaller extent by the inductor DCR value. To achieve high efficiency operation, care
should be taken in selecting inductors featuring a quality factor above 25 at the switching frequency. Increasing
the inductor value produces lower RMS currents, but degrades transient response. For a given physical inductor
size, increased inductance usually results in an inductor with lower saturation current.
The total losses of the coil consist of both the losses in the DC resistance, R(DC) , and the following frequency-
dependent components:
•
•
•
•
The losses in the core material (magnetic hysteresis loss, especially at high switching frequencies)
Additional losses in the conductor from the skin effect (current displacement at high frequencies)
Magnetic field losses of the neighboring windings (proximity effect)
Radiation losses
The following inductor series from different suppliers have been used with the TPS6125x converters.
Table 4. List of Inductors
MANUFACTURER
SERIES
DIMENSIONS (in mm)
3.2 x 2.5 x 1.2 max. height
3.2 x 2.5 x 1.0 max. height
2.5 x 2.0 x 1.0 max. height
3.2 x 2.5 x 1.2 max. height
HITACHI METALS
KSLI-322512BL1-1R0
LQM32PN1R0MG0
LQM2HPN1R0MG0
DFE322512C-1R0
MURATA
TOKO
20
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Link(s): TPS61253 TPS61254 TPS61256 TPS61258
TPS61253, TPS61254, TPS61256, TPS61258
www.ti.com
SLVSAG8B –SEPTEMBER 2011–REVISED MAY 2012
OUTPUT CAPACITOR
For the output capacitor, it is recommended to use small ceramic capacitors placed as close as possible to the
VOUT and GND pins of the IC. If, for any reason, the application requires the use of large capacitors which can
not be placed close to the IC, using a smaller ceramic capacitor in parallel to the large one is highly
recommended. This small capacitor should be placed as close as possible to the VOUT and GND pins of the IC.
To get an estimate of the recommended minimum output capacitance, Equation 6 can be used.
IOUT
g
V
- V
)
OUT IN
(
CMIN
=
f g DV g VOUT
(6)
Where f is the switching frequency which is 3.5MHz (typ.) and ΔV is the maximum allowed output ripple.
With a chosen ripple voltage of 20mV, a minimum effective capacitance of 9μF is needed. The total ripple is
larger due to the ESR of the output capacitor. This additional component of the ripple can be calculated using
Equation 7
VESR = IOUT g RESR
(7)
An MLCC capacitor with twice the value of the calculated minimum should be used due to DC bias effects. This
is required to maintain control loop stability. The output capacitor requires either an X7R or X5R dielectric. Y5V
and Z5U dielectric capacitors, aside from their wide variation in capacitance over temperature, become resistive
at high frequencies. There are no additional requirements regarding minimum ESR. Larger capacitors cause
lower output voltage ripple as well as lower output voltage drop during load transients but the total output
capacitance value should not exceed ca. 50µF.
DC bias effect: high cap. ceramic capacitors exhibit DC bias effects, which have a strong influence on the
device's effective capacitance. Therefore the right capacitor value has to be chosen very carefully. Package size
and voltage rating in combination with material are responsible for differences between the rated capacitor value
and it's effective capacitance. For instance, a 10µF X5R 6.3V 0603 MLCC capacitor would typically show an
effective capacitance of less than 4µF (under 5V bias condition, high temperature).
In applications featuring high pulsed load currents (e.g. TPS61253 based solution) it is recommended to run the
converter with a reasonable amount of effective output capacitance, for instance x2 10µF X5R 6.3V 0603 MLCC
capacitors connected in parallel.
INPUT CAPACITOR
Multilayer ceramic capacitors are an excellent choice for input decoupling of the step-up converter as they have
extremely low ESR and are available in small footprints. Input capacitors should be located as close as possible
to the device. While a 4.7μF input capacitor is sufficient for most applications, larger values may be used to
reduce input current ripple without limitations.
Take care when using only ceramic input capacitors. When a ceramic capacitor is used at the input and the
power is being supplied through long wires, such as from a wall adapter, a load step at the output can induce
ringing at the VIN pin. This ringing can couple to the output and be mistaken as loop instability or could even
damage the part. Additional "bulk" capacitance (electrolytic or tantalum) should in this circumstance be placed
between CI and the power source lead to reduce ringing than can occur between the inductance of the power
source leads and CI.
Copyright © 2011–2012, Texas Instruments Incorporated
Submit Documentation Feedback
21
Product Folder Link(s): TPS61253 TPS61254 TPS61256 TPS61258
TPS61253, TPS61254, TPS61256, TPS61258
SLVSAG8B –SEPTEMBER 2011–REVISED MAY 2012
www.ti.com
CHECKING LOOP STABILITY
The first step of circuit and stability evaluation is to look from a steady-state perspective at the following signals:
•
•
•
Switching node, SW
Inductor current, IL
Output ripple voltage, VOUT(AC)
These are the basic signals that need to be measured when evaluating a switching converter. When the
switching waveform shows large duty cycle jitter or the output voltage or inductor current shows oscillations, the
regulation loop may be unstable. This is often a result of board layout and/or L-C combination.
As a next step in the evaluation of the regulation loop, the load transient response is tested. The time between
the application of the load transient and the turn on of the P-channel MOSFET, the output capacitor must supply
all of the current required by the load. VOUT immediately shifts by an amount equal to ΔI(LOAD) x ESR, where ESR
is the effective series resistance of COUT. ΔI(LOAD) begins to charge or discharge COUT generating a feedback
error signal used by the regulator to return VOUT to its steady-state value. The results are most easily interpreted
when the device operates in PWM mode.
During this recovery time, VOUT can be monitored for settling time, overshoot or ringing that helps judge the
converter’s stability. Without any ringing, the loop has usually more than 45° of phase margin. Because the
damping factor of the circuitry is directly related to several resistive parameters (e.g., MOSFET rDS(on)) that are
temperature dependant, the loop stability analysis has to be done over the input voltage range, load current
range, and temperature range.
LAYOUT CONSIDERATIONS
For all switching power supplies, the layout is an important step in the design, especially at high peak currents
and high switching frequencies. If the layout is not carefully done, the regulator could show stability problems as
well as EMI problems. Therefore, use wide and short traces for the main current path and for the power ground
tracks. The input capacitor, output capacitor, and the inductor should be placed as close as possible to the IC.
Use a common ground node for power ground and a different one for control ground to minimize the effects of
ground noise. Connect these ground nodes at any place close to the ground pins of the IC.
BP
GND
GND
U1
EN
VIN
VOUT
L1
Figure 37. Suggested Layout (Top)
22
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Link(s): TPS61253 TPS61254 TPS61256 TPS61258
TPS61253, TPS61254, TPS61256, TPS61258
www.ti.com
SLVSAG8B –SEPTEMBER 2011–REVISED MAY 2012
THERMAL INFORMATION
Implementation of integrated circuits in low-profile and fine-pitch surface-mount packages typically requires
special attention to power dissipation. Many system-dependent issues such as thermal coupling, airflow, added
heat sinks and convection surfaces, and the presence of other heat-generating components affect the power-
dissipation limits of a given component.
Three basic approaches for enhancing thermal performance are listed below:
•
•
•
Improving the power dissipation capability of the PCB design
Improving the thermal coupling of the component to the PCB
Introducing airflow in the system
As power demand in portable designs is more and more important, designers must figure the best trade-off
between efficiency, power dissipation and solution size. Due to integration and miniaturization, junction
temperature can increase significantly which could lead to bad application behaviors (i.e. premature thermal
shutdown or worst case reduce device reliability).
Junction-to-ambient thermal resistance is highly application and board-layout dependent. In applications where
high maximum power dissipation exists (e.g. TPS61253 or TPS61259 based solutions), special care must be
paid to thermal dissipation issues in board design. The device operating junction temperature (TJ) should be kept
below 125°C.
Copyright © 2011–2012, Texas Instruments Incorporated
Submit Documentation Feedback
23
Product Folder Link(s): TPS61253 TPS61254 TPS61256 TPS61258
TPS61253, TPS61254, TPS61256, TPS61258
SLVSAG8B –SEPTEMBER 2011–REVISED MAY 2012
www.ti.com
TYPICAL APPLICATION
CLASS-D APA
Audio Input
Audio Input
TPS61254
SW
L
4.5 V / VIN
EN IHF
VOUT
BP
1 μH
EN HP
VIN
EN
10 uF
VIN
2.65 V .. 4.35 V
4.7 μF
GND
CLASS-AB APA
Audio Input
Audio Input
EN DC/DC
EN HP
AUDIO AMPLIFIER (HANDS-FREE, HEADPHONE)
Figure 38. Combined Audio Amplifier Power Supply
TPS61256
L
5.0 V, up to 750mA
SW
VIN
EN
VOUT
BP
VIN
3.3 V .. 4.8 V
1 μH
Class-D APA
Audio Input
Audio Input
10 uF
4.7 μF
GND
EN
EN DC/DC
EN APA
Figure 39. "Boosted" Audio Power Supply
CLASS-D APA
Audio Input L
Audio Input L
TPS61253
L
5 V, up to 1500mA
EN APA
SW
VIN
EN
VOUT
BP
1 μH
10 uF (x2)
VIN
3.3 V .. 4.35 V
GND
10 μF
CLASS-D APA
Audio Input R
Audio Input R
EN DC/DC
EN APA
HIGH-POWER CLASS-D AUDIO AMPLIFIER
Figure 40. "Boosted" Stereo Audio Power Supply
24
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Link(s): TPS61253 TPS61254 TPS61256 TPS61258
TPS61253, TPS61254, TPS61256, TPS61258
www.ti.com
SLVSAG8B –SEPTEMBER 2011–REVISED MAY 2012
4.7µF
CLASS-D APA
Audio Input L
Audio Input L
EN APA
TPS61253
SW
L
5 V, up to 1500mA
VOUT
BP
1 μH
4.7µF
VIN
EN
10 µF (x2)
CLASS-D APA
VIN
3.3 V .. 4.35 V
GND
10 μF
Audio Input R
Audio Input R
EN APA
EN DC/DC
HIGH-POWER CLASS-D AUDIO AMPLIFIER
TPD4S214
VUSB
VOTG_IN
VBUS
5V, 500mA
USB-OTG Port
100nF
4.7µF
Data
EN
DET
FLT
ADJ
D+
D-
ID
GND
VIO
USB PHY
Figure 41. Single Cell Li-Ion Power Solution for Tablet PCs featuring
"Boosted" Audio Power Supply and USB-OTG I/F
TPS22945
5V HDMI Power
IN
OUT
5V, 100mA
HDMI Port
1 μF
100nF
Data
Enable DC/DC
Enable USB, HDMI
VIO
OC
ON
≥ 1000µs
≥ 0µs
Enable HDMI
GND
TPS61259
L
TPS2052B
IN
L
1 μH
VOUT
BP
5V USB Power
100nF
VIN
3.2 V .. 5.25 V
OUT1
OUT2
5V, 500mA
USB Port #1
100nF
150µF(1)(2)
VIN
EN
Data
Data
10 uF
OC1
EN1
OC2
4.7 μF
GND
5V USB Power
100nF
Enable USB1
Enable USB2
5V, 500mA
USB Port #2
150µF(1)(2)
EN2
GND
Enable DC/DC
(1) Requirement for USB host applications.
VIO
Downstream facing ports should be bypassed with 120µF min. per hub.
(2) Bypass capacitor should be tantalum type (>10V rated voltage).
Figure 42. Single Cell Li-Ion Power Solution for Tablet PCs featuring x2 USB Host Ports, HDMI I/F
Copyright © 2011–2012, Texas Instruments Incorporated
Submit Documentation Feedback
25
Product Folder Link(s): TPS61253 TPS61254 TPS61256 TPS61258
TPS61253, TPS61254, TPS61256, TPS61258
SLVSAG8B –SEPTEMBER 2011–REVISED MAY 2012
www.ti.com
PACKAGE SUMMARY
CHIP SCALE PACKAGE
(BOTTOM VIEW)
CHIP SCALE PACKAGE
(TOP VIEW)
A3
B3
C3
A2
A1
B1
C1
YMS
CC
D
B2
LLLL
C2
E
A1
Code:
•
•
•
•
YM - 2 digit date code
S - assembly site code
CC - chip code (see ordering table)
LLLL - lot trace code
PACKAGE DIMENSIONS
The dimensions for the YFF-9 package are shown in Table 5. See the package drawing at the end of this data
sheet.
Table 5. YFF-9 Package Dimensions
Packaged Devices
D
E
TPS6125xYFF
1.206 ±0.03 mm
1.306 ±0.03 mm
26
Submit Documentation Feedback
Copyright © 2011–2012, Texas Instruments Incorporated
Product Folder Link(s): TPS61253 TPS61254 TPS61256 TPS61258
TPS61253, TPS61254, TPS61256, TPS61258
www.ti.com
SLVSAG8B –SEPTEMBER 2011–REVISED MAY 2012
REVISION HISTORY
Note: Page numbers of current revision may differ from previous versions.
Changes from Original (September 2011) to Revision A
Page
•
Changed device TPS61256 to production status ................................................................................................................. 2
Changes from Revision A (October 2011) to Revision B
Page
•
•
•
•
•
•
Added TPS61253 and TPS61258 to data sheet header as production devices .................................................................. 1
Changed devices TPS61253 and TPS61258 to production status ...................................................................................... 2
Changed graphic entity for Figure 5 ..................................................................................................................................... 9
Changed graphic entity for Figure 12 ................................................................................................................................. 10
Changed graphic entity for Figure 15 ................................................................................................................................. 11
Changed graphic entity for Figure 25 ................................................................................................................................. 14
Copyright © 2011–2012, Texas Instruments Incorporated
Submit Documentation Feedback
27
Product Folder Link(s): TPS61253 TPS61254 TPS61256 TPS61258
PACKAGE OPTION ADDENDUM
www.ti.com
18-May-2012
PACKAGING INFORMATION
Status (1)
Eco Plan (2)
MSL Peak Temp (3)
Samples
Orderable Device
Package Type Package
Drawing
Pins
Package Qty
Lead/
Ball Finish
(Requires Login)
TPS61253YFFR
TPS61253YFFT
TPS61254YFFR
TPS61254YFFT
TPS61256YFFR
TPS61256YFFT
TPS61258YFFR
TPS61258YFFT
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
YFF
YFF
YFF
YFF
YFF
YFF
YFF
YFF
9
9
9
9
9
9
9
9
3000
250
Green (RoHS
& no Sb/Br)
SNAGCU Level-1-260C-UNLIM
Green (RoHS
& no Sb/Br)
SNAGCU Level-1-260C-UNLIM
SNAGCU Level-1-260C-UNLIM
SNAGCU Level-1-260C-UNLIM
SNAGCU Level-1-260C-UNLIM
SNAGCU Level-1-260C-UNLIM
SNAGCU Level-1-260C-UNLIM
SNAGCU Level-1-260C-UNLIM
3000
250
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
3000
250
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
3000
250
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
18-May-2012
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
2-Jun-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TPS61253YFFR
TPS61254YFFR
TPS61254YFFT
TPS61256YFFR
TPS61256YFFT
TPS61258YFFR
TPS61258YFFT
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
YFF
YFF
YFF
YFF
YFF
YFF
YFF
9
9
9
9
9
9
9
3000
3000
250
180.0
180.0
180.0
180.0
180.0
180.0
180.0
8.4
8.4
8.4
8.4
8.4
8.4
8.4
1.41
1.41
1.41
1.41
1.41
1.41
1.41
1.31
1.31
1.31
1.31
1.31
1.31
1.31
0.69
0.69
0.69
0.69
0.69
0.69
0.69
4.0
4.0
4.0
4.0
4.0
4.0
4.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
Q1
Q1
Q1
Q1
Q1
Q1
Q1
3000
250
3000
250
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
2-Jun-2012
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TPS61253YFFR
TPS61254YFFR
TPS61254YFFT
TPS61256YFFR
TPS61256YFFT
TPS61258YFFR
TPS61258YFFT
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
YFF
YFF
YFF
YFF
YFF
YFF
YFF
9
9
9
9
9
9
9
3000
3000
250
210.0
210.0
210.0
210.0
210.0
210.0
210.0
185.0
185.0
185.0
185.0
185.0
185.0
185.0
35.0
35.0
35.0
35.0
35.0
35.0
35.0
3000
250
3000
250
Pack Materials-Page 2
X: Max = 1.356 mm, Min =1.256 mm
Y: Max = 1.256 mm, Min =1.156 mm
X: Max = 1.356 mm, Min =1.256 mm
Y: Max = 1.256 mm, Min =1.156 mm
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Audio
Applications
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
www.ti.com/security
Medical
Logic
Security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense www.ti.com/space-avionics-defense
microcontroller.ti.com
www.ti-rfid.com
Video and Imaging
www.ti.com/video
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明