TPS62801YKAT [TI]
1.75-V to 5.5-V input, 1-A ultra-low IQ step-down converter in 0.7-mm x 1.05-mm chip scale package | YKA | 6 | -40 to 125;型号: | TPS62801YKAT |
厂家: | TEXAS INSTRUMENTS |
描述: | 1.75-V to 5.5-V input, 1-A ultra-low IQ step-down converter in 0.7-mm x 1.05-mm chip scale package | YKA | 6 | -40 to 125 开关 |
文件: | 总40页 (文件大小:5588K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
TPS6280x 采用6 引脚0.35mm 间距WCSP 封装的
1.75V 至5.5V、0.6A/1A、2.3µA IQ 降压转换器
1 特性
3 说明
• 1.75V 至5.5V 输入电压范围
• 2.3µA 工作静态电流
• 开关频率高达4MHz
• 0.6A 或1A 输出电流
• 1% 的输出电压精度
• 可选择省电和强制PWM 模式
• R2D 转换器,可实现灵活的输出电压测试
• 16 种可选输出电压和1 种固定输出电压
TPS6280x 器件系列是一款降压转换器,具有 2.3µA
的典型静态电流以及出色的效率和超小的解决方案尺
寸。该器件利用 TI 的 DCS-Control™ 拓扑,能够与微
型电感器和电容器配合使用,并且具有高达 4MHz 的
开关频率。在轻负载条件下,该器件会无缝进入节能模
式,从而减少开关周期数并保持高效率。
将 VSEL/MODE 引脚连接到 GND 可以选择固定输出
电压。只需将一个外部电阻器连接到 VSEL/MODE 引
脚,就可以选择 16 种内部设置的输出电压。使用集成
R2D(电阻器到数字)转换器,可读取外部电阻器并设
置输出电压。仅需通过更换单个电阻,相同的器件型号
即可用于不同的应用和电压轨。此外,与传统的外部电
阻分压器网络相比,内部设置的输出电压可提供更高的
精度。该器件启动之后,直流/直流转换器将进入强制
PWM 模式(通过在 VSEL/MODE 引脚上施加高电
平)。在该工作模式下,此器件通常以 4MHz 或
1.5MHz 的开关频率运行,从而能够实现最低的输出电
压纹波和最高的效率。TPS6280x 器件系列采用具有
0.35mm 间距的微型6 引脚WCSP 封装。
– TPS62800 (4MHz):0.4V 至0.775V
– TPS62801 (4MHz):0.8V 至1.55V
– TPS62802 (4MHz):1.8V 至3.3V
– TPS62806 (1.5MHz):0.4V 至0.775V
– TPS62807 (1.5MHz):0.8V 至1.55V
– TPS62808 (1.5MHz):1.8V 至3.3V
• 智能使能引脚
• 经过优化的引脚排列,可支持0201 元件
• DCS-Control 拓扑
• 输出放电
• 以100% 的占空比运行
• 微型6 引脚0.35mm 间距WCSP 封装
• 支持小于0.6mm 的解决方案高度
• 支持小于5mm2 的解决方案尺寸
• 借助以下工具创建定制设计方案:
器件信息
封装(1)
封装尺寸(标称值)
器件型号
TPS62800
TPS62801
TPS62802
TPS62806
TPS62807
– TPS62800 WEBENCH® Power Designer
– TPS62801 WEBENCH® Power Designer
– TPS62802 WEBENCH® Power Designer
– TPS62806 WEBENCH® Power Designer
– TPS62807 WEBENCH® Power Designer
– TPS62808 WEBENCH® Power Designer
1.05 mm × 0.70 mm ×
0.4 mm
DSBGA (6)
(1) 如需了解所有可用封装,请参阅数据表末尾的可订购产品附
录。
2 应用
• 可穿戴电子产品、物联网应用
• 2 节AA 电池供电型应用
• 智能手机
TPS62801
95
90
85
80
75
70
65
16 selectable VOUT
VIN
1.75V – 5.5V
L = 0.47 µH
0.8 V – 1.55 V
VIN
SW
COUT
CIN
4.7
10
F
GND
VOS
F
PWM
ON
OFF
VSEL/
MODE
PFM
EN
RVSEL
TPS62801
VIN
1.75 V–5.5 V
1.2-V VOUT fixed
COUT
60
55
50
45
40
L = 0.47 µH
VIN = 1.8V
VIN = 2.5V
VIN = 3.3V
VIN = 3.6V
VIN = 4.2V
VIN = 5.0V
VIN
SW
CIN
4.7
10
F
GND
VOS
F
ON
OFF
VSEL/
MODE
EN
0.001
0.01
0.1
1
IOUT [mA ]
10
100
1000
SLVS
典型应用
V
OUT 为1.2V 时,效率与IOUT 间的关系
本文档旨在为方便起见,提供有关TI 产品中文版本的信息,以确认产品的概要。有关适用的官方英文版本的最新信息,请访问
www.ti.com,其内容始终优先。TI 不保证翻译的准确性和有效性。在实际设计之前,请务必参考最新版本的英文版本。
English Data Sheet: SLVSDD1
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
www.ti.com.cn
Table of Contents
9 Application and Implementation..................................15
9.1 Application Information............................................. 15
9.2 Typical Application.................................................... 15
9.3 System Examples..................................................... 28
10 Power Supply Recommendations..............................30
11 Layout...........................................................................30
11.1 Layout Guidelines................................................... 30
11.2 Layout Example...................................................... 30
12 Device and Documentation Support..........................31
12.1 Device Support....................................................... 31
12.2 接收文档更新通知................................................... 31
12.3 支持资源..................................................................31
12.4 Trademarks.............................................................31
12.5 Electrostatic Discharge Caution..............................31
12.6 术语表..................................................................... 32
13 Mechanical, Packaging, and Orderable
1 特性................................................................................... 1
2 应用................................................................................... 1
3 说明................................................................................... 1
4 Revision History.............................................................. 2
5 器件比较表.........................................................................3
6 Pin Configuration and Functions...................................3
7 Specifications.................................................................. 5
7.1 Absolute Maximum Ratings........................................ 5
7.2 ESD Ratings............................................................... 5
7.3 Recommended Operating Conditions.........................5
7.4 Thermal Information....................................................6
7.5 Electrical Characteristics.............................................6
7.6 Typical Characteristics................................................8
8 Detailed Description......................................................10
8.1 Overview...................................................................10
8.2 Functional Block Diagram.........................................10
8.3 Feature Description...................................................10
8.4 器件功能模式............................................................ 13
Information.................................................................... 32
4 Revision History
注:以前版本的页码可能与当前版本的页码不同
Changes from Revision E (July 2018) to Revision F (June 2022)
Page
• 更新了整个文档中的表格、图和交叉参考的编号格式.........................................................................................1
• 将最小输入电压更新为1.75V............................................................................................................................. 1
• Updated max rising UVLO spec......................................................................................................................... 6
Changes from Revision D (July 2018) to Revision E (January 2019)
Page
• 在整个数据表中添加了TPS62807 和TPS62808 器件.......................................................................................1
Copyright © 2022 Texas Instruments Incorporated
2
Submit Document Feedback
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
www.ti.com.cn
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
5 器件比较表
借助
RVSEL
实现的可选择的
输出电压
fSW
[MHz]
IOUT
[A]
软
启动,tSS
功能
VSEL/MODE
输出
放电
器件
固定输出电压
0.4V 至0.775V
(阶跃为25mV)
TPS62800
TPS62801
TPS62802
TPS62806
TPS62807
TPS62808
VSEL + MODE
VSEL + MODE
VSEL + MODE
VSEL + MODE
VSEL + MODE
VSEL + MODE
0.7V (VSEL/MODE = GND)
1.20V (VSEL/MODE = GND)
1.8V (VSEL/MODE = GND)
0.7V (VSEL/MODE = GND)
1.20V (VSEL/MODE = GND)
1.8V (VSEL/MODE = GND)
4
4
1
1
125µs
125µs
400µs
125µs
125µs
125µs
是
是
是
是
是
是
0.8V 至1.55V
(阶跃为50mV)
1.8V 至3.3V
(阶跃为100mV)
4
1
0.4V 至0.775V
(阶跃为25mV)
1.5
1.5
1.5
0.6
0.6
0.6
0.8V 至1.55V
(阶跃为50mV)
1.8V 至3.3V
(阶跃为100mV)
6 Pin Configuration and Functions
1
2
GND
VOS
A
B
C
VIN
SW
VSEL/MODE
EN
Not to scale
图6-1. 6-Pin DSBGA YKA Package (Top View)
表6-1. Pin Functions
Pin
I/O
Description
Name
NO.
GND supply pin. Connect this pin close to the GND terminal of the input and output
capacitor.
GND
A1
PWR
PWR
VIN power supply pin. Connect the input capacitor close to this pin for best noise and voltage
spike suppression. A ceramic capacitor is required.
VIN
B1
C1
Connecting a resistor to GND selects a pre-defined output voltage. Once the device has
started up, the R2D converter is disabled and the pin operates as an input. Applying a high
level selects forced PWM mode operation and a low level power save mode operation.
VSEL/MODE
IN
Output voltage sense pin for the internal feedback divider network and regulation loop. This
pin also discharges VOUT by an internal MOSFET when the converter is disabled. Connect
this pin directly to the output capacitor with a short trace.
VOS
SW
A2
B2
IN
The switch pin is connected to the internal MOSFET switches. Connect the inductor to this
terminal.
OUT
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
3
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
www.ti.com.cn
表6-1. Pin Functions (continued)
Pin
I/O
Description
Name
NO.
A high level enables the devices, and a low level turns the device off. The pin features an
internal pulldown resistor, which is disabled once the device has started up.
EN
C2
IN
表6-2. Output Voltage Setting (VSEL/MODE Pin)
Output Voltage Setting VOUT [V]
RVSELResistance [kΩ], E96 Resistor Series,
VSEL
1% Accuracy, Temperature Coefficient Better or Equal
than ±200 ppm/°C
TPS62800
TPS62806
TPS62801
TPS62807
TPS62802
TPS62808
0
1
0.700
0.400
0.425
0.450
0.475
0.500
0.525
0.550
0.575
0.600
0.625
0.650
0.675
0.700
0.725
0.750
0.775
1.2
0.8
1.8
1.8
1.9
2.0
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
3.0
3.1
3.2
3.3
Connected to GND (no resistor needed)
10.0
12.1
2
0.85
0.9
3
15.4
4
0.95
1.0
18.7
5
23.7
6
1.05
1.1
28.7
7
36.5
8
1.15
1.2
44.2
9
56.2
10
11
12
13
14
15
16
1.25
1.3
68.1
86.6
1.35
1.4
105.0
133.0
162.0
205.0
249.0 or larger
1.45
1.5
1.55
Copyright © 2022 Texas Instruments Incorporated
4
Submit Document Feedback
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
www.ti.com.cn
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
7 Specifications
7.1 Absolute Maximum Ratings
MIN(1)
–0.3
–0.3
–2.5
–0.3
–0.3
–40
MAX(1)
UNIT
V
VIN
SW
6
VIN + 0.3 V
V
Pin voltage(2)
SW (AC), less than 10 ns while switching
9
6
V
EN, VSEL/MODE
VOS
V
5
V
Operating junction temperature, TJ
Storage temperature, Tstg
150
150
°C
°C
–65
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute–maximum–rated conditions for extended periods may affect device reliability.
(2) All voltage values are with respect to network ground terminal GND.
7.2 ESD Ratings
VALUE
±2000
±500
UNIT
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins(1)
Electrostatic
discharge
V(ESD)
V
Charged device model (CDM), per JEDEC specification JESD22-C101, all pins(2)
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. The human body
model is a 100-pF capacitor discharged through a 1.5-kΩresistor into each pin.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
7.3 Recommended Operating Conditions
MIN
NOM
MAX
5.5
1
UNIT
V
VIN
Supply voltage, VIN
1.75
IOUT
IOUT
IOUT
L
A
Output current, VIN ≥2.3 V, TPS62800, TPS62801, TPS62802
Output current, VIN < 2.3 V, TPS62800, TPS62801, TPS62802
Output current, TPS62806, TPS62807, TPS62808
Effective inductance, TPS62800, TPS62801, TPS62802
Effective output capacitance, TPS62800, TPS62801, TPS62802
Effective inductance, TPS62806, TPS62807, TPS62808
Effective output capacitance, TPS62806, TPS62807, TPS62808
Effective input capacitance
0.7
0.6
0.82
26
A
A
0.33
2
0.47
1.0
µH
µF
µH
µF
µF
pF
COUT
L
0.7
3
1.2
26
COUT
CIN
0.5
4.7
CVSEL/MODE
External parasitic capacitance at the VSEL/MODE pin
30
Resistance range for external resistor at VSEL/MODE pin (E96 1%
resistor values)
10
249
kΩ
RVSEL
External resistor tolerance E96 series at VSEL/MODE pin
E96 resistor series temperature coefficient (TCR)
Operating junction temperature range
1%
+200
125
ppm/°C
°C
–200
–40
TJ
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
5
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
www.ti.com.cn
UNIT
7.4 Thermal Information
YKA (DSBGA)
6 PINS
147.7
1.7
THERMAL METRIC(1)
RθJA
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
RθJC(top)
RθJB
47.5
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
0.5
ψJT
47.6
ψJB
RθJC(bot)
—
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
7.5 Electrical Characteristics
VIN = 3.6 V, TJ = –40°C to 125°C typical values are at TJ = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SUPPLY
EN = VIN, IOUT = 0 µA, VOUT = 1.2 V,
device not switching, TJ = –40°C to +85°C
2.3
2.5
8
4
µA
µA
Operating quiescent current
(power save mode)
IQ
EN = VIN, IOUT = 0 µA, VOUT = 1.2 V, device switching
Operating quiescent current EN = VIN, VSEL/MODE = VIN (after power up),
mA
(PWM mode)
device switching, IOUT = 0 mA, VOUT = 1.2 V
EN = GND, shutdown current into VIN
VSEL/MODE = GND, TJ = –40°C to +85°C
,
ISD
Shutdown current
120
250
nA
VTH_ UVLO+
VTH_UVLO–
INPUT EN
VIH TH
Rising VIN
Falling VIN
1.65
1.56
1.75
1.7
V
V
Undervoltage lockout
threshold
High level input voltage
Low level input voltage
Input bias current
0.8
0.8
V
V
VIL TH
0.4
25
IIN
10
nA
TJ = –40°C to +85°C, EN = high
RPD
Internal pulldown resistance EN = low
500
kΩ
INPUT VSEL/MODE
High level input voltage
(digital input)
VIH TH
V
Low level input voltage
(digital input)
VIL TH
IIN
0.4
25
V
Input bias current
EN = high
10
nA
POWER
SWITCHES
Leakage current into the SW
pin
ILKG_SW
10
120
80
25
170
115
1.2
nA
mΩ
mΩ
A
VSW = 1.2 V, TJ = –40°C to +85°C
IOUT = 500 mA
High side MOSFET
on-resistance
RDS(ON)
Low side MOSFET
on-resistance
IOUT = 500 mA
High-side MOSFET switch
current limit
ILIMF
ILIMF
TPS62806, TPS62807, TPS62808
TPS62806, TPS62807, TPS62808
0.95
0.85
1.1
1
Low-side MOSFET switch
current limit
1.1
A
TPS62800, TPS62801
TPS62802
1.3
1.4
1.2
1.3
1.45
1.55
1.35
1.45
1.55
1.65
1.45
1.55
A
A
A
A
High-side MOSFET switch
current limit
ILIMF
TPS62800, TPS62801
TPS62802
Low-side MOSFET switch
current limit
ILIMF
OUTPUT VOLTAGE DISCHARGE
Copyright © 2022 Texas Instruments Incorporated
6
Submit Document Feedback
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
www.ti.com.cn
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
VIN = 3.6 V, TJ = –40°C to 125°C typical values are at TJ = 25°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
EN = GND, IVOS = –10 mA into the VOS pin
TJ = –40°C to +85°C
RDSCH_VOS
MOSFET on-resistance
7
11
Ω
Bias current into the VOS
pin
EN = VIN, VOUT = 1.2 V (internal 12-MΩresistor
divider), TJ = –40°C to +85°C
IIN_VOS
100
400
nA
THERMAL PROTECTION
Thermal shutdown
Rising junction temperature, PWM mode
160
20
°C
°C
temperature
TSD
Thermal shutdown
hysteresis
OUTPUT
VOUT
VOUT
VOUT
VOUT
VOUT
VOUT
fSW
Output voltage range
Output voltage range
Output voltage range
Output voltage accuracy
Output voltage accuracy
Output voltage accuracy
Switching frequency
TPS62800, TPS62806, 25-mV steps
TPS62801, TPS62807, 50-mV steps
TPS62802, TPS62808, 100-mV steps
Power save mode
0.4
0.8
1.8
0.775
1.55
3.3
V
V
V
0%
0%
0%
4
PWM mode, IOUT = 0 mA, TJ = 25°C to +85°C
1%
–1%
–2%
1.7%
PWM mode, IOUT = 0 mA, TJ = –40°C to +125°C
VIN = 3.6 V, VOUT = 1.2 V, PWM operation
MHz
MHz
TPS62806
VIN = 3.6 V, VOUT = 0.7 V, PWM operation
fSW
Switching frequency
Switching frequency
Switching frequency
1.5
1.5
TPS62807
VIN = 3.6 V, VOUT = 1.2 V, PWM operation
fSW
MHz
MHz
µs
TPS62808
VIN = 3.6 V, VOUT = 1.8 V, PWM operation
fSW
1.5
Regulator start-up delay
time
From transition EN = low to high until device starts
switching, VSEL = 16
tStartup_delay
500
125
125
400
1100
170
210
500
TPS62801, from VOUT = 0 V to 0.95% of VOUT
nominal
tSS
tSS
tSS
Soft-start time
Soft-start time
Soft-start time
µs
TPS62800, TPS62806, TPS62807, TPS62808
from VOUT = 0 V to 0.95% of VOUT nominal
µs
TPS62802, from VOUT = 0 V to 0.95% of VOUT
nominal
µs
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
7
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
www.ti.com.cn
7.6 Typical Characteristics
0.5
5
4.5
4
TJ = -40°C
TJ = -10°C
TJ = 30°C
TJ = 85°C
TJ = 125°C
0.45
0.4
0.35
0.3
3.5
3
0.25
0.2
2.5
2
0.15
0.1
1.5
1
TJ = -40°C
TJ = -10°C
TJ = 30°C
TJ = 85°C
TJ = 125°C
0.05
0
0.5
0
1.5
2
2.5
3
3.5
VIN [V]
4
4.5
5
5.5
1.5
2
2.5
3
3.5
VIN [V]
4
4.5
5
5.5
EN = GND
Device not switching
图7-1. Shutdown Current, ISD
图7-2. Quiescent Current, IQ
14
13
12
11
10
9
1000
100
10
TJ = -40°C
TJ = 25°C
TJ = 85°C
TJ = -40°C
TJ = 25°C
TJ = 85°C
8
7
6
5
4
1
3
2
1
0
0.1
0
0.5
1
1.5
2
2.5 3
VIN [V]
3.5
4
4.5
5
5.5
0
0.5
1
1.5
2
2.5 3
VIN [V]
3.5
4
4.5
5
5.5
VIN falling
EN = VIN
Device switching, no load, VOUT = 1.2 V
VSEL/MODE = GND
VIN rising
EN = VIN
Device switching, no load, VOUT = 1.2 V
VSEL/MODE = GND
图7-3. Operating Quiescent Current, IQ
图7-4. Operating Quiescent Current, IQ
350
200
175
150
125
100
75
TJ = -40°C
TJ = -10°C
TJ = 30°C
TJ = 85°C
TJ = 125°C
TJ = -40°C
325
300
275
250
225
200
175
150
125
100
75
TJ = -10°C
TJ = 30°C
TJ = 85°C
TJ = 125°C
50
50
25
25
0
0
1.5
2
2.5
3
3.5
VIN [V]
4
4.5
5
5.5
1.5
2
2.5
3
3.5
VIN [V]
4
4.5
5
5.5
图7-5. High-Side Switch Drain Source Resistance, 图7-6. Low-Side Switch Drain Source Resistance,
RDS(ON)
RDS(ON)
Copyright © 2022 Texas Instruments Incorporated
8
Submit Document Feedback
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
www.ti.com.cn
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
20
18
16
14
12
10
8
TJ = -40°C
TJ = -10°C
TJ = 30°C
TJ = 85°C
TJ = 125°C
6
4
2
0
1.5
2
2.5
3
3.5
VIN [V]
4
4.5
5
5.5
图7-7. VOS Discharge Switch Drain Source Resistance, RDSCH_VOS
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
9
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
www.ti.com.cn
8 Detailed Description
8.1 Overview
The TPS6280x is a high frequency synchronous step-down converter with ultra-low quiescent current
consumption. Using TI's DCS-Control topology, the device extends the high efficiency operation area down to
microamperes of load current during power save mode operation. TI's DCS-Control (Direct Control with
Seamless Transition into power save mode) is an advanced regulation topology, which combines the
advantages of hysteretic and voltage mode control. Characteristics of DCS-Control are excellent AC load
regulation and transient response, low output ripple voltage, and a seamless transition between PFM and PWM
mode operation. DCS-Control includes an AC loop, which senses the output voltage (VOS pin) and directly
feeds the information to a fast comparator stage. This comparator sets the switching frequency, which is
constant for steady state operating conditions, and provides immediate response to dynamic load changes. In
order to achieve accurate DC load regulation, a voltage feedback loop is used. The internally compensated
regulation network achieves fast and stable operation with small external components and low-ESR capacitors.
8.2 Functional Block Diagram
EN
Smart Enable
Ultra Low Power
0.4V VREF
UVLO
Pulldown Control
Input Buffer
500kW
VOS
Thermal Shutdown
Control Logic
VOS
R2D converter
UVLO
VOUT
Discharge
VSEL/
MODE
Internal
VFB feedback
divider
EN
Resistor to
Digital
Converter
network
Power Stage
Current
Limit Comparator
VIN
SW
Power Save /
Forced PWM
Mode operation
Limit
High Side
PMOS
VIN
TON
Timer
DCS Control
VOS
Ramp
VOS
Gate Driver
Direct Control
Startup Delay
VFB
VREF
NMOS
Softstart Timing
Limit
Low Side
Error
amplifier
Main
Comparator
GND
Current
Limit Comparator
图8-1. Functional Block Diagram
8.3 Feature Description
8.3.1 Smart Enable and Shutdown (EN)
An internal 500-kΩ resistor pulls the EN pin to GND and avoids the pin to be floating, which prevents an
uncontrolled start-up of the device in case the EN pin cannot be driven to low level safely. With EN low, the
device is in shutdown mode. The device is turned on with EN set to a high level. The pulldown control circuit
disconnects the pulldown resistor on the EN pin once the internal control logic and the reference have been
powered up. With EN set to a low level, the device enters shutdown mode and the pulldown resistor is activated
again.
Copyright © 2022 Texas Instruments Incorporated
10
Submit Document Feedback
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
www.ti.com.cn
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
8.3.2 Soft Start
Once the device has been enabled with EN high, it initializes and powers up its internal circuits, which occurs
during the regulator start-up delay time, tStartup_delay. Once tStartup_delay expires, the internal soft-start circuitry
ramps up the output voltage within the soft-start time, tss. See 图8-2.
The start-up delay time, tStartup_delay, varies depending on the selected VSEL value. tStartup_delay is shortest with
VSEL = 0 and longest with VSEL = 16. See 图9-42 to 图9-46.
EN
Device starts switching
and ramps VOUT
VOUT
tStartup_delay
tSS
图8-2. Device Start-Up
8.3.3 VSEL/MODE Pin
This pin has two functions: output voltage selection during start-up of the converter and operating mode
selection. See 节5.
8.3.3.1 Output Voltage Selection (R2D Converter)
The output voltage is set with a single external resistor connected between the VSEL/MODE pin and GND. Once
the device has been enabled and the control logic as well as the internal reference have been powered up, a
R2D (resistor-to-digital) conversion is started to detect the external resistor RVSEL within the regulator start-up
delay time, tStartup_delay. An internal current source applies current through the external resistor and an internal
ADC reads back the resulting voltage level. Depending on the level, an internal feedback divider network is
selected to set the correct output voltage. Once this R2D conversion is finished, the current source is turned off
to avoid current flow through the external resistor.
After power up, the pin is configured as an input for mode selection. Therefore, the output voltage is set only
once. If the mode selection function is used in combination with the VSEL function, ensure that there is no
additional current path or capacitance greater than 30 pF total to GND during R2D conversion. Otherwise, the
additional current to GND is interpreted as a lower resistor value and a false output voltage is set. 表6-2 lists the
correct resistor values for RVSEL to set the appropriate output voltages. The R2D converter is designed to
operate with resistor values out of the E96 table and requires 1% resistor value accuracy. The external resistor,
RVSEL, is not a part of the regulator feedback loop and has therefore no impact on the output voltage accuracy.
Ensure that there is no other leakage path than the RVSEL resistor at the VSEL/MODE pin during an
undervoltage lockout event. Otherwise, a false output voltage will be set.
Connecting VSEL/MODE to GND selects a pre-defined output voltage.
• TPS62800 = 0.7 V
• TPS62801 = 1.2 V
• TPS62802 = 1.8 V
• TPS62806 = 0.7 V
• TPS62807 = 1.2 V
• TPS62808 = 1.8 V
In this case, no external resistor is needed, which enables a smaller solution size.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
11
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
www.ti.com.cn
8.3.3.2 Mode Selection —Power Save Mode and Forced PWM Operation
A low level at this pin selects power save mode operation, and a high level selects forced PWM operation. The
mode can be changed during operation after the device has been powered up. The mode selection function is
only available after the R2D converter has read out the external resistor.
8.3.4 Undervoltage Lockout (UVLO)
To avoid misoperation of the device at low input voltages, an undervoltage lockout (UVLO) comparator monitors
the supply voltage. The UVLO comparator shuts down the device at an input voltage of 1.7 V (maximum) with
falling VIN. The device starts at an input voltage of 1.75 V (maximum) rising VIN. Once the device re-enters
operation out of an undervoltage lockout condition, it behaves like being enabled. The internal control logic is
powered up and the external resistor at the VSEL/MODE pin is read out.
8.3.5 Switch Current Limit and Short Circuit Protection
The TPS6280x integrates a current limit on the high-side and low-side MOSFETs to protect the device against
overload or short circuit conditions. The current in the switches is monitored cycle by cycle. If the high-side
MOSFET current limit, ILIMF, trips, the high-side MOSFET is turned off and the low-side MOSFET is turned on to
ramp down the inductor current. Once the inductor current through the low-side switch decreases below the low-
side MOSFET current limit, ILIMF, the low-side MOSFET is turned off and the high-side MOSFET turns on again.
8.3.6 Thermal Shutdown
The junction temperature (TJ) of the device is monitored by an internal temperature sensor. If TJ exceeds the
thermal shutdown temperature, TSD, of 160°C (typical), the device enters thermal shutdown. Both the high-side
and low-side power FETs are turned off. When TJ decreases below the hysteresis amount of typically 20°C, the
converter resumes operation, beginning with a soft start to the originally set VOUT (there is no R2D conversion of
RVSEL). The thermal shutdown is not active in power save mode.
8.3.7 Output Voltage Discharge
The purpose of the output discharge function is to ensure a defined down-ramp of the output voltage when the
device is disabled and to keep the output voltage close to 0 V. The output discharge feature is only active once
the device has been enabled at least once since the supply voltage was applied. The output discharge function
is not active if the device is disabled and the supply voltage is applied the first time.
The internal discharge resistor is connected to the VOS pin. The discharge function is enabled as soon as the
device is disabled. The minimum supply voltage required to keep the discharge function active is VIN
VTH_UVLO-
>
.
Copyright © 2022 Texas Instruments Incorporated
12
Submit Document Feedback
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
www.ti.com.cn
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
8.4 器件功能模式
8.4.1 Power Save Mode Operation
The DCS-Control topology supports power save mode operation. At light loads, the device operates in PFM
(pulse frequency modulation) mode that generates a single switching pulse to ramp up the inductor current and
recharge the output capacitor, followed by a sleep period where most of the internal circuits are shut down to
achieve lowest operating quiescent current. During this time, the load current is supported by the output
capacitor. The duration of the sleep period depends on the load current and the inductor peak current. During
the sleep periods, the current consumption is reduced to typically 2.3 µA. This low quiescent current
consumption is achieved by an ultra-low power voltage reference, an integrated high impedance feedback
divider network, and an optimized power save mode operation.
In PFM mode, the switching frequency varies linearly with the load current. At medium and high load conditions,
the device automatically enters PWM (pulse width modulation) mode and operates in continuous conduction
mode with a nominal switch frequency, fsw, of typically 4 MHz or 1.5 MHz. The switching frequency in PWM
mode is controlled and depends on VIN and VOUT. The boundary between PWM and PFM mode is when the
inductor current becomes discontinuous.
If the load current decreases, the converter seamlessly enters PFM mode to maintain high efficiency down to
very light loads. Since DCS-Control supports both operation modes within one single building block, the
transition from PWM to PFM ,mode is seamless with minimum output voltage ripple.
8.4.2 Forced PWM Mode Operation
After the device has powered up and ramped up VOUT, the VSEL/MODE pin acts as an input. With a high level
on VSEL/MODE pin, the device enters forced PWM mode and operates with a constant switching frequency
over the entire load range, even at very light loads. This action reduces or eliminates interference with RF and
noise sensitive circuits, but lowers efficiency at light loads.
8.4.3 100% Mode Operation
The duty cycle of the buck converter operating in PWM mode is given as D = VOUT / VIN. The duty cycle
increases as the input voltage comes close to the output voltage. In 100% duty cycle mode, the device keeps
the high-side switch on continuously. The high-side switch stays turned on as long as the output voltage is below
the internal set point, which allows the conversion of small input to output voltage differences.
8.4.4 Optimized Transient Performance from PWM-to-PFM Mode Operation
For most converters, the load transient response in PWM mode is improved compared to PFM mode, since the
converter reacts faster on the load step and actively sinks energy on the load release. Compare 图 9-33 to 图
9-32. As an additional feature, the TPS6280x automatically enters PWM mode for 16 cycles after a heavy load
release to bring the output voltage back to the regulation level faster. After 16 cycles of PWM mode, the device
automatically returns to PFM mode (if VSEL/MODE is driven low). See 图 8-3. Without this optimization, the
output voltage overshoot would be higher and would look like the VOUT' trace. This feature is only active once the
load is high enough and the converter operates in PWM mode.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
13
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
www.ti.com.cn
VOUT
‘
VOUT
16 PWM
Cycles
PWM
Mode
PFM Mode
图8-3. Optimized Transient Performance from PWM-to-PFM Mode
Copyright © 2022 Texas Instruments Incorporated
14
Submit Document Feedback
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
www.ti.com.cn
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
9 Application and Implementation
备注
以下应用部分中的信息不属于TI 器件规格的范围,TI 不担保其准确性和完整性。TI 的客 户应负责确定
器件是否适用于其应用。客户应验证并测试其设计,以确保系统功能。
9.1 Application Information
The following section discusses the design of the external components to complete the power supply design for
several input and output voltage options by using typical applications as a reference.
9.2 Typical Application
TPS62801
VIN
16 selectable VOUT
0.8 V–1.55 V
L = 0.47 µH
1.75 V–5.5 V
VIN
SW
COUT
CIN
4.7
10
F
F
GND
VOS
PWM
ON
OFF
VSEL/
MODE
PFM
RVSEL
EN
图9-1. TPS62801 Adjustable VOUT Application Circuit
Additional circuits are shown in 节9.3.
9.2.1 Design Requirements
表9-1 shows the list of components for the application circuit and the characteristic application curves
表9-1. Components for Application Characteristic Curves
Reference
Description
Value
Size [L × W × T]
Manufacturer(1)
TPS62801 / 2
Step down converter
1.05 mm × 0.70 mm × 0.4 mm maximum
Texas Instruments
Ceramic capacitor,
GRM155R60J475ME47D
0402 (1 mm × 0.5 mm × 0.6 mm
maximum)
CIN
COUT
L
4.7 µF
10 µF
Murata
Murata
Murata
Ceramic capacitor,
GRM155R60J106ME15D
0402 (1 mm × 0.5 mm × 0.65 mm
maximum)
0603 (1.6 mm × 0.8 mm × 1.0 mm
maximum)
Inductor DFE18SANR47MG0L
0.47 µH
(1) See the Third-party Products Disclaimer.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
15
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
www.ti.com.cn
9.2.2 Detailed Design Procedure
9.2.2.1 Custom Design With WEBENCH® Tools
Click here to create a custom design using the TPS62800 device with the WEBENCH® Power Designer.
Click here to create a custom design using the TPS62801 device with the WEBENCH® Power Designer.
Click here to create a custom design using the TPS62802 device with the WEBENCH® Power Designer.
Click here to create a custom design using the TPS62806 device with the WEBENCH® Power Designer.
Click here to create a custom design using the TPS62807 device with the WEBENCH® Power Designer.
Click here to create a custom design using the TPS62808 device with the WEBENCH® Power Designer.
1. Start by entering the input voltage (VIN), output voltage (VOUT), and output current (IOUT) requirements.
2. Optimize the design for key parameters such as efficiency, footprint, and cost using the optimizer dial.
3. Compare the generated design with other possible solutions from Texas Instruments.
The WEBENCH Power Designer provides a customized schematic along with a list of materials with real-time
pricing and component availability.
In most cases, these actions are available:
• Run electrical simulations to see important waveforms and circuit performance
• Run thermal simulations to understand board thermal performance
• Export customized schematic and layout into popular CAD formats
• Print PDF reports for the design, and share the design with colleagues
Get more information about WEBENCH tools at www.ti.com/WEBENCH.
9.2.2.2 Inductor Selection
The inductor value affects the peak-to-peak ripple current, the PWM-to-PFM transition point, the output voltage
ripple, and the efficiency. The selected inductor has to be rated for its DC resistance and saturation current. The
inductor ripple current (ΔIL) decreases with higher inductance and increases with higher VIN or VOUT and can be
estimated according to 方程式1.
方程式 2 calculates the maximum inductor current under static load conditions. The saturation current of the
inductor must be rated higher than the maximum inductor current, as calculated with 方程式 2, which is
recommended because during a heavy load transient the inductor current rises above the calculated value. A
more conservative way is to select the inductor saturation current according to the high-side MOSFET switch
current limit, ILIMF
.
Vout
Vin
1-
DIL = Vout ´
L ´ ¦
(1)
(2)
DI
L
I
= I
+
Lmax
outmax
2
where
• f = switching frequency
• L = inductor value
• ΔIL = peak-to-peak inductor ripple current
• ILmax = maximum inductor current
Copyright © 2022 Texas Instruments Incorporated
16
Submit Document Feedback
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
www.ti.com.cn
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
表9-2 shows a list of possible inductors.
表9-2. List of Possible Inductors
Size Imperial
(Metric)
Inductance [µH]
Inductor Series
Dimensions L × W × T
Supplier(1)
0.47
0.47
0.47
0.47
1.0
DFE18SAN_G0
HTEB16080F
HTET1005FE
TFM160808ALC
DFE201610E
0603 (1608)
0603 (1608)
0402 (1005)
0603 (1608)
0806 (201610)
1.6 mm × 0.8 mm × 1.0 mm maximum
1.6 mm × 0.8 mm × 0.6 mm maximum
1.0 mm × 0.5 mm × 0.65 mm maximum
1.6 mm × 0.8 mm × 0.8 mm maximum
2.0 mm × 1.6 mm × 1.0 mm maximum
Murata
Cyntec
Cyntec
TDK
Murata
(1) See the Third-party Products Disclaimer.
9.2.2.3 Output Capacitor Selection
The DCS-Control scheme of the TPS6280x allows the use of tiny ceramic capacitors. Ceramic capacitors with
low-ESR values have the lowest output voltage ripple and are recommended. The output capacitor requires
either an X7R or X5R dielectric. At light load currents, the converter operates in power save mode and the output
voltage ripple is dependent on the output capacitor value. A larger output capacitors can be used reducing the
output voltage ripple.
The inductor and output capacitor together provide a low-pass filter. To simplify this process, 表 9-3 outlines
possible inductor and capacitor value combinations.
表9-3. Recommended LC Output Filter Combinations
Nominal Output Capacitor Value [µF]
Device
Nominal Inductor Value [µH]
4.7 µF
10 µF
2 × 10 µF
22 µF
√
TPS62800,
TPS62801
0.47(1)
0.47(1)
(3)
√
√
√
√
(3)
TPS62802
√
√
TPS62806,
TPS62807,
TPS62808
1.0(2)
(3)
√
√
√
√
(1) An effective inductance range of 0.33 µH to 0.82 µH is recommended. An effective capacitance range of 2 µF to 26 µF is
recommended.
(2) An effective inductance range of 0.7 µH to 1.2 µH is recommended. An effective capacitance range of 3 µF to 26 µF is recommended.
(3) Typical application configuration. Other check marks indicate alternative filter combinations.
9.2.2.4 Input Capacitor Selection
Because the buck converter has a pulsating input current, a low-ESR ceramic input capacitor is required for best
input voltage filtering to minimize input voltage spikes. For most applications, a 4.7-µF input capacitor is
sufficient. When operating from a high impedance source, like a coin cell, a larger input buffer capacitor ≥ 10
μF is recommended to avoid voltage drops during start-up and load transients. The input capacitor can be
increased without any limit for better input voltage filtering. The leakage current of the input capacitor adds to the
overall current consumption.
表9-4 shows a selection of input and output capacitors.
表9-4. List of Possible Capacitors
Size Imperial
Capacitor Part Number
GRM155R60J475ME47D
GRM035R60J475ME15
Dimensions L × W × T
Supplier(1)
Murata
Capacitance [μF]
(Metric)
1.0 mm × 0.5 mm × 0.6 mm
maximum
4.7
4.7
0402 (1005)
0.6 mm × 0.3 mm × 0.55 mm
maximum
0201 (0603)
Murata
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
17
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
www.ti.com.cn
表9-4. List of Possible Capacitors (continued)
Size Imperial
(Metric)
Capacitor Part Number
Dimensions L × W × T
Supplier(1)
Capacitance [μF]
1.0 mm × 0.5 mm × 0.65 mm
maximum
10
GRM155R60J106ME15D
0402 (1005)
Murata
(1) See the Third-party Products Disclaimer.
Copyright © 2022 Texas Instruments Incorporated
18
Submit Document Feedback
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
www.ti.com.cn
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
9.2.3 Application Curves
The conditions for the below application curves are VIN = 3.6 V, VOUT = 1.2 V, and the components listed in 表
9-1, unless otherwise noted.
85
80
75
70
65
60
55
50
45
40
35
30
25
20
85
80
75
70
65
60
55
50
45
40
35
30
25
20
VIN = 1.8V
VIN = 2.5V
VIN = 3.3V
VIN = 3.6V
VIN = 4.2V
VIN = 5.0V
VIN = 1.8V
VIN = 2.5V
VIN = 3.3V
VIN = 3.6V
VIN = 4.2V
VIN = 5.0V
0.01
0.1
1
10
IOUT [mA ]
100
1000
0.01
0.1
1
10
IOUT [mA ]
100
1000
SLVS
SLVS
TPS62800
TPS62800
VSEL/MODE = GND
RVSEL = 10 kΩto GND
图9-3. Efficiency Power Save Mode
图9-2. Efficiency Power Save Mode
VOUT = 0.7 V
VOUT = 0.4 V
95
95
90
85
80
75
70
65
60
55
50
45
40
90
85
80
75
70
65
60
55
50
45
40
VIN = 1.8V
VIN = 2.6V
VIN = 3.6V
VIN = 4.2V
VIN = 5.0V
VIN = 2.3V
VIN = 2.7V
VIN = 3.7V
VIN = 4.2V
VIN = 5.0V
0.001
0.01
0.1
1
IOUT [mA ]
10
100
1000
0.001
0.01
0.1
1
IOUT [mA]
10
100
1000
SLVS
SLVS
TPS62801
TPS62801
RVSEL = 10 kΩto GND
RVSEL = 15.4 kΩto GND
图9-4. Efficiency Power Save Mode
图9-5. Efficiency Power Save Mode
VOUT = 0.8 V
VOUT = 0.9 V
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
19
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
www.ti.com.cn
95
90
85
80
75
70
65
60
55
50
45
40
90
80
70
60
50
40
VIN = 1.8V
VIN = 2.5V
VIN = 3.3V
VIN = 3.6V
VIN = 4.2V
VIN = 5.0V
VIN = 1.8V
30
VIN = 2.5V
VIN = 3.3V
VIN = 3.6V
VIN = 4.2V
VIN = 5.0V
20
10
0
1
10
100
1000
0.001
0.01
0.1
1
IOUT [mA ]
10
100
1000
IOUT [mA ]
SLVS
SLVS
TPS62801
RVSEL = 56.2 kΩ
TPS62801
VSEL/MODE = GND
VSEL/MODE pin = high after start-up
图9-7. Efficiency Power Save Mode
图9-6. Efficiency Forced PWM Mode
VOUT = 1.2 V
VOUT = 1.2 V
90
85
80
75
70
65
100
95
90
85
80
75
70
65
60
55
50
45
40
60
DFE18SAN_G0 R47 (1.6 x 1.6 x 1.0 mm)
HTEB16080F R47 (1.6 x 1.6 x 0.6 mm)
HTET1005FE R47 (1.0 x 0.5 x 0.65 mm)
TFM160808ALC R47 (1.6 x 1.6 x 0.8 mm)
55
VIN = 2.5V
VIN = 3.3V
VIN = 3.6V
VIN = 4.2V
VIN = 5.0V
50
45
40
0.01
0.1
1
10
100
1000
0.001
0.01
0.1
1
IOUT [mA ]
10
100
1000
IOUT [mA ]
SLPVloSt
SLVS
TPS62801
VSEL/MODE = GND, VOUT = 1.2 V
TPS62802
VSEL/MODE = GND
图9-8. Inductor Comparison
图9-9. Efficiency Power Save Mode
VOUT = 1.8 V
95
100
95
90
85
80
75
70
65
60
55
50
45
40
90
85
80
75
70
65
60
55
50
45
40
VIN = 1.8V
VIN = 2.5V
VIN = 3.3V
VIN = 3.8V
VIN = 4.5V
VIN = 5.0V
VIN = 3.6V
VIN = 3.8V
VIN = 4.2V
VIN = 5.0V
0.01
0.1
1
10
100
600
IOUT [mA ]
SLVS
0.001
0.01
0.1
1
IOUT [mA ]
10
100
1000
TPS62806
VOUT = 0.7 V, VSEL/MODE = GND
L = 1-µH DFE201610E
SLVS
TPS62802
3.3 V VOUT, VSEL/MODE = 249 k
图9-11. Efficiency Power Save Mode
图9-10. Efficiency Power Save Mode
VOUT = 0.7 V
VOUT = 3.3 V
Copyright © 2022 Texas Instruments Incorporated
20
Submit Document Feedback
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
www.ti.com.cn
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
100
95
90
85
80
75
70
65
60
55
50
45
100
95
90
85
80
75
70
65
VIN=1.8V
VIN=2.1V
VIN=2.7V
VIN=3.3V
VIN=3.6V
VIN=4.2V
VIN=4.8V
60
55
50
45
40
VIN=2.7V
VIN=3.3V
VIN=3.6V
VIN=4.2V
VIN=4.8V
40
10m
100m
1m 10m
Load Current [A]
100m
1
10m
100m
1m 10m
Load Current [A]
100m
1
Effi
Effi
TPS62807
VOUT = 1.2 V, VSEL/MODE = GND
L = 1-µH DFE201610E
TPS62808
VOUT = 1.8 V, VSEL/MODE = GND
L = 1-µH DFE201610E
图9-12. Efficiency Power Save Mode
图9-13. Efficiency Power Save Mode
VOUT = 1.2 V
VOUT = 1.8 V
1.248
1.248
TJ = 25°C
TJ = -40°C
1.236
1.224
1.212
1.200
1.188
1.176
1.164
1.236
1.224
1.212
1.200
1.188
1.176
1.164
VIN = 1.8V
VIN = 2.5V
VIN = 3.3V
VIN = 3.6V
VIN = 4.2V
VIN = 5.0V
VIN = 1.8V
VIN = 2.5V
VIN = 3.3V
VIN = 3.6V
VIN = 4.2V
VIN = 5.0V
0.01
0.1
1
10
IOUT [mA ]
100
1000
0.01
0.1
1
10
IOUT [mA ]
100
1000
SLVS
SLVS
TPS62801
VSEL/MODE = GND
PFM/PWM mode TJ = 25°C
TPS62801
VSEL/MODE = GND
PFM/PWM mode
VOUT = 1.2 V
VOUT = 1.2 V
TJ = –40°C
图9-14. Output Voltage vs Output Current
图9-15. Output Voltage vs Output Current
1.248
1.212
TJ = 85°C
TJ = 25°C
1.236
1.224
1.212
1.200
1.188
1.200
VIN = 1.8V
VIN = 2.5V
VIN = 3.3V
VIN = 3.6V
VIN = 4.2V
VIN = 5.0V
VIN = 1.8V
VIN = 2.5V
VIN = 3.3V
VIN = 3.6V
VIN = 4.2V
VIN = 5.0V
1.176
1.164
1.188
0.01
0.01
0.1
1
10
IOUT [mA ]
100
1000
0.1
1
10
IOUT [mA ]
100
1000
SLVS
SLVS
TPS62801
VSEL/MODE = GND
PFM/PWM mode TJ = 85°C
TPS62801
VSEL/MODE = high after start-up
Forced PWM mode TJ = 25°C
VOUT = 1.2 V
VOUT = 1.2 V
图9-16. Output Voltage vs Output Current
图9-17. Output Voltage vs Output Current
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
21
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
www.ti.com.cn
1.212
1.200
1.188
1.212
TJ = 85°C
TJ = -40°C
1.200
VIN = 1.8V
VIN = 2.5V
VIN = 3.3V
VIN = 3.6V
VIN = 4.2V
VIN = 5.0V
VIN = 1.8V
VIN = 2.5V
VIN = 3.3V
VIN = 3.6V
VIN = 4.2V
VIN = 5.0V
0.01
0.1
1
10
IOUT [mA ]
100
1000
1.188
0.01
0.1
1
10
IOUT [mA ]
100
1000
SLVS
SLVS
TPS62801
VSEL/MODE = high after start-up
Forced PWM mode TJ = 85°C
TPS62801
VSEL/MODE = high after start-up
Forced PWM mode
VOUT = 1.2 V
VOUT = 1.2 V
TJ = –40°C
图9-19. Output Voltage vs Output Current
图9-18. Output Voltage vs Output Current
5000
4500
4000
3500
3000
2500
100
90
80
70
60
50
2000
40
VIN = 1.8V
VIN = 1.8V
1500
1000
500
0
30
20
10
0
VIN = 2.5V
VIN = 3.3V
VIN = 3.6V
VIN = 4.2V
VIN = 5.0V
VIN = 2.5V
VIN = 3.3V
VIN = 3.6V
VIN = 4.2V
VIN = 5.0V
0
100 200 300 400 500 600 700 800 900 1000
IOUT [mA]
0
1
2
3
4
5
IOUT [mA]
6
7
8
9
10
SLVS
SLVS
TPS62801
VSEL/MODE = GND
PFM/PWM mode TJ = 25°C
TPS62801
VOUT = 1.2 V
VSEL/MODE = GND
VOUT = 1.2 V
PFM/PWM mode
TJ = 25°C
图9-20. Switching Frequency vs Output Current
图9-21. Switching Frequency (Zoom In)
5000
4500
4000
3500
3000
2500
4500
4000
3500
3000
2500
2000
1500
1000
500
2000
VIN = 1.8V
1500
1000
500
0
VIN = 2.5V
VIN = 3.3V
VIN = 3.6V
VIN = 4.2V
VIN = 5.0V
VIN = 1.8V
VIN = 3.6V
VIN = 4.2V
VIN = 5.0V
0
100 200 300 400 500 600 700 800 900 1000
IOUT [mA]
0
SLVS
0
100 200 300 400 500 600 700 800 900 1000
IOUT [mA]
TPS62801
VSEL/MODE = high after start-up
Forced PWM Mode TJ = 25°C
SLVS
VOUT = 1.2 V
TPS62801
VOUT = 0.8 V
VSEL/MODE = 10 kΩto GND
PFM/PWM mode TJ = 25°C
图9-22. Switching Frequency vs Output Current
图9-23. Switching Frequency vs Output Current
Copyright © 2022 Texas Instruments Incorporated
22
Submit Document Feedback
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
www.ti.com.cn
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
2000
1800
1600
1400
1200
1000
800
VIN = 1.8V
600
VIN = 2.5V
VIN = 3.3V
VIN = 3.6V
VIN = 4.2V
VIN = 5.0V
400
200
0
0
60 120 180 240 300 360 420 480 540 600
IOUT [mA]
SLVS
TPS62801
VOUT = 1.2 V
IOUT = 25 µA
VSEL/MODE = GND
PFM mode
TPS62806
VOUT = 0.7 V
VSEL/MODE = GND
PFM/PWM mode
L = 1 µH
TJ = 25°C
图9-25. Typical Operation Power Save Mode
图9-24. Switching Frequency vs Output Current
TPS62801
VOUT = 1.2 V
IOUT = 10 mA
VSEL/MODE = GND
PFM mode
VOUT = 0.7 V
VIN = 3.8 V
IOUT = 10 mA
VSEL/MODE = GND
PFM Mode, L = 1-µH DFE201610E
图9-26. Typical Operation Power Save Mode
图9-27. TPS62806 Typical Operation Power Save
Mode
VOUT = 0.7 V
VIN = 3.8 V
IOUT = 0 mA
VSEL/MODE = VIN
(after start-up)
PWM mode
VOUT = 1.2 V
VSEL/MODE = GND
IOUT = 500 mA
PFM Mode, L = 1-µH DFE201610E
图9-29. TPS62801 Typical Operation PWM Mode
图9-28. TPS62806 Typical Forced PWM Mode
Operation (1.5 MHz)
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
23
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
www.ti.com.cn
Forced PWM
VOUT = 1.2 V
IOUT = 0 mA
TPS62801
rise / fall time < 1
µs
VOUT = 1.2 V
VSEL/MODE = GND
mode
IOUT = 0 mA to 50 mA, PFM Mode
VSEL/MODE = VIN (after start-up)
图9-30. TPS62801 Typical Operation Forced PWM
图9-31. Load Transient Power Save Mode
Mode
TPS62801
VOUT = 1.2 V
VSEL/MODE = GND
PFM / PWM mode
Forced
VOUT = 1.2 V
VSEL/MODE = VIN
(after start-up)
rise / fall time < 1 µs
PWM mode
IOUT = 5 mA to 500 mA
rise / fall time < 1 µs
IOUT = 5 mA to 500 mA
图9-32. Load Transient Power Save Mode
图9-33. TPS62801 Load Transient Forced PWM
Mode
Copyright © 2022 Texas Instruments Incorporated
24
Submit Document Feedback
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
www.ti.com.cn
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
TPS62801
VOUT = 1.2 V
VSEL/MODE = GND
PFM/PWM mode
TPS62801
VOUT = 1.2 V
VSEL/MODE = VIN
(after start-up)
IOUT = 1 mA to 1 A 1 kHz
IOUT = 1 mA to 1 A, 1 kHz
Forced PWM mode
图9-34. AC Load Sweep Power Save Mode
图9-35. AC Load Sweep Forced PWM Mode
TPS62801
VOUT = 1.2 V
VIN = 3.6 V to 4.2 V
IOUT = 50 mA
TPS62801
VOUT = 1.2 V
VIN = 3.6 V to 4.2 V
IOUT = 500 mA
rise / fall time = 10 µs
rise / fall time = 10 µs
图9-36. Line Transient PFM Mode
图9-37. Line Transient PWM Mode
VOUT = 0.8 V
RVSEL = 10 kΩ
VSEL/MODE = Low (through RVSEL
)
TPS62801
VOUT = 1.2 V
VSEL/MODE = GND
RLoad = 220 Ω
RLoad = 220 Ω
图9-38. TPS62801 Start-Up, VOUT = 0.8 V
图9-39. Start-Up, VOUT = 1.2 V
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
25
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
www.ti.com.cn
VOUT = 1.55 V
VSEL/MODE = Low (through RVSEL
)
TPS62801
VOUT = 1.2 V
VSEL/MODE = VIN
No load
EN = high to low
RLoad = 220 Ω
RVSEL = 249 kΩ
图9-41. Output Discharge
图9-40. TPS62801 Start-Up, VOUT = 1.55 V
tStartup_delay = 290ms
tStartup_delay = 300ms
VSEL/MODE = GND
RVSEL = 10 kΩ
图9-42. Start-Up Delay Time, VSEL = 0
图9-43. Start-Up Delay Time, VSEL = 1
tStartup_delay = 427ms
tStartup_delay = 363ms
RVSEL = 36.5 kΩ
RVSEL = 44.2 kΩ
图9-44. Start-Up Delay Time, VSEL = 7
图9-45. Start-Up Delay Time, VSEL = 8
Copyright © 2022 Texas Instruments Incorporated
26
Submit Document Feedback
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
www.ti.com.cn
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
tStartup_delay = 500ms
RVSEL = 249 kΩ
图9-46. Start-Up Delay Time, VSEL = 16
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
27
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
www.ti.com.cn
9.3 System Examples
This section shows additional circuits for various output voltages.
TPS62801
VIN
L = 0.47 µH
1.75 V–5.5 V
1.2-V VOUT fixed
COUT
VIN
SW
CIN
4.7
10
F
GND
VOS
F
ON
OFF
VSEL/
MODE
EN
图9-47. TPS62801 VSEL Connected to GND for 1.2-V Fixed VOUT
TPS62801
VIN
16 selectable VOUT
0.8 V–1.55 V
L = 0.47 µH
1.75 V–5.5 V
VIN
SW
COUT
CIN
4.7
10
F
F
GND
VOS
PWM
ON
OFF
VSEL/
MODE
PFM
RVSEL
EN
图9-48. TPS62801 Adjustable VOUT Application Circuit
TPS62802
L = 0.47 µH
VIN
1.75 V–5.5 V
VOUT = 3.3 V
VIN
SW
CIN
4.7
COUT
2 × 10
=
F
F
GND
VOS
PWM
ON
OFF
VSEL/
MODE
EN
PFM
R
VSEL
=
249 k
图9-49. TPS62802 Adjustable 3.3-V VOUT Application Circuit
Copyright © 2022 Texas Instruments Incorporated
28
Submit Document Feedback
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
www.ti.com.cn
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
TPS62802
VIN
1.8 V fixed
L = 0.47 µH
1.75 V–5.5 V
VIN
SW
COUT
10 F
CIN
4.7 F
GND
VOS
ON
OFF
VSEL/
MODE
EN
图9-50. TPS62802 VSEL Connected to GND for 1.8-V Fixed VOUT
16 selectable VOUT
0.4 V–0.775 V
IOUT up to 600 mA
TPS62806
VIN
L = 1 µH
1.75 V–5.5 V
VIN
SW
COUT
CIN
4.7
10
F
GND
EN
VOS
F
PWM
ON
OFF
VSEL/
MODE
PSM
RVSEL
图9-51. TPS62806 Adjustable VOUT Application Circuit
TPS62806
0.7 V fixed VOUT
IOUT up to 600 mA
VIN
L = 1 µH
1.75 V–5.5 V
VIN
SW
COUT
CIN
4.7
10
F
GND
VOS
F
ON
OFF
VSEL/
MODE
EN
图9-52. TPS62806 VSEL Connected to GND for 0.7-V Fixed VOUT
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
29
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
www.ti.com.cn
10 Power Supply Recommendations
The power supply must provide a current rating according to the supply voltage, output voltage, and output
current of the TPS6280x.
11 Layout
11.1 Layout Guidelines
The pinout of TPS6280x has been optimized to enable a single top layer PCB routing of the IC and its critical
passive components such as CIN, COUT, and L. Furthermore, this pinout allows the user to connect tiny
components such as 0201 (0603) size capacitors and a 0402 (1005) size inductor. A solution size smaller than 5
mm2 can be achieved with a fixed output voltage.
• As for all switching power supplies, the layout is an important step in the design. Take care in board layout to
get the specified performance.
• It is critical to provide a low inductance, low impedance ground path. Therefore, use wide and short traces for
the main current paths.
• The input capacitor should be placed as close as possible to the VIN and GND pins of the IC. This is the
most critical component placement.
• The VOS line is a sensitive, high impedance line and should be connected to the output capacitor and routed
away from noisy components and traces (for example, SW line) or other noise sources.
11.2 Layout Example
VOUT
GND
COUT
GND
VIN
VOS
SW
EN
CIN
L
VSEL/
MODE
RVSEL
VIN
GND
图11-1. PCB Layout Example
Copyright © 2022 Texas Instruments Incorporated
30
Submit Document Feedback
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
www.ti.com.cn
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
12 Device and Documentation Support
12.1 Device Support
12.1.1 第三方产品免责声明
TI 发布的与第三方产品或服务有关的信息,不能构成与此类产品或服务或保修的适用性有关的认可,不能构成此
类产品或服务单独或与任何TI 产品或服务一起的表示或认可。
12.1.2 Development Support
12.1.2.1 Custom Design With WEBENCH® Tools
Click here to create a custom design using the TPS62800 device with the WEBENCH® Power Designer.
Click here to create a custom design using the TPS62801 device with the WEBENCH® Power Designer.
Click here to create a custom design using the TPS62802 device with the WEBENCH® Power Designer.
Click here to create a custom design using the TPS62806 device with the WEBENCH® Power Designer.
Click here to create a custom design using the TPS62807 device with the WEBENCH® Power Designer.
Click here to create a custom design using the TPS62808 device with the WEBENCH® Power Designer.
1. Start by entering the input voltage (VIN), output voltage (VOUT), and output current (IOUT) requirements.
2. Optimize the design for key parameters such as efficiency, footprint, and cost using the optimizer dial.
3. Compare the generated design with other possible solutions from Texas Instruments.
The WEBENCH Power Designer provides a customized schematic along with a list of materials with real-time
pricing and component availability.
In most cases, these actions are available:
• Run electrical simulations to see important waveforms and circuit performance
• Run thermal simulations to understand board thermal performance
• Export customized schematic and layout into popular CAD formats
• Print PDF reports for the design, and share the design with colleagues
Get more information about WEBENCH tools at www.ti.com/WEBENCH.
12.2 接收文档更新通知
要接收文档更新通知,请导航至 ti.com 上的器件产品文件夹。点击订阅更新 进行注册,即可每周接收产品信息更
改摘要。有关更改的详细信息,请查看任何已修订文档中包含的修订历史记录。
12.3 支持资源
TI E2E™ 支持论坛是工程师的重要参考资料,可直接从专家获得快速、经过验证的解答和设计帮助。搜索现有解
答或提出自己的问题可获得所需的快速设计帮助。
链接的内容由各个贡献者“按原样”提供。这些内容并不构成 TI 技术规范,并且不一定反映 TI 的观点;请参阅
TI 的《使用条款》。
12.4 Trademarks
DCS-Control™ and TI E2E™ are trademarks of Texas Instruments.
WEBENCH® is a registered trademark of Texas Instruments.
所有商标均为其各自所有者的财产。
12.5 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric changes could cause the device not to meet its published
specifications.
Copyright © 2022 Texas Instruments Incorporated
Submit Document Feedback
31
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
TPS62800, TPS62801, TPS62802, TPS62806, TPS62807, TPS62808
ZHCSHT6F –DECEMBER 2017 –REVISED JUNE 2022
www.ti.com.cn
12.6 术语表
TI 术语表
本术语表列出并解释了术语、首字母缩略词和定义。
13 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2022 Texas Instruments Incorporated
32
Submit Document Feedback
Product Folder Links: TPS62800 TPS62801 TPS62802 TPS62806 TPS62807 TPS62808
PACKAGE OPTION ADDENDUM
www.ti.com
20-Jun-2022
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
TPS62800YKAR
TPS62801YKAR
TPS62801YKAT
TPS62802YKAR
TPS62802YKAT
TPS62806YKAR
TPS62806YKAT
TPS62807YKAR
TPS62807YKAT
TPS62808YKAR
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
YKA
YKA
YKA
YKA
YKA
YKA
YKA
YKA
YKA
YKA
6
6
6
6
6
6
6
6
6
6
3000 RoHS & Green SAC396 | SNAGCU
3000 RoHS & Green SAC396 | SNAGCU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-
Samples
Samples
Samples
Samples
Samples
Samples
Samples
Samples
Samples
Samples
+
+
X
X
J
250
3000 RoHS & Green SAC396 | SNAGCU
250 RoHS & Green SAC396 | SNAGCU
3000 RoHS & Green SAC396 | SNAGCU
250 RoHS & Green SAC396 | SNAGCU
3000 RoHS & Green SAC396 | SNAGCU
250 RoHS & Green SAC396 | SNAGCU
3000 RoHS & Green SAC396 | SNAGCU
RoHS & Green SAC396 | SNAGCU
J
L
L
V
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
20-Jun-2022
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
7-Jul-2023
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
K0
P1
W
B0
Reel
Diameter
Cavity
A0
A0 Dimension designed to accommodate the component width
B0 Dimension designed to accommodate the component length
K0 Dimension designed to accommodate the component thickness
Overall width of the carrier tape
W
P1 Pitch between successive cavity centers
Reel Width (W1)
QUADRANT ASSIGNMENTS FOR PIN 1 ORIENTATION IN TAPE
Sprocket Holes
Q1 Q2
Q3 Q4
Q1 Q2
Q3 Q4
User Direction of Feed
Pocket Quadrants
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TPS62800YKAR
TPS62801YKAR
TPS62801YKAR
TPS62801YKAT
TPS62801YKAT
TPS62802YKAR
TPS62802YKAR
TPS62802YKAT
TPS62806YKAR
TPS62806YKAT
TPS62806YKAT
TPS62807YKAR
TPS62807YKAR
TPS62807YKAT
TPS62807YKAT
TPS62808YKAR
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
YKA
YKA
YKA
YKA
YKA
YKA
YKA
YKA
YKA
YKA
YKA
YKA
YKA
YKA
YKA
YKA
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
3000
3000
3000
250
180.0
178.0
180.0
180.0
178.0
180.0
178.0
180.0
180.0
180.0
178.0
180.0
178.0
180.0
178.0
180.0
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
8.4
0.81
0.81
0.81
0.81
0.81
0.81
0.81
0.81
0.81
0.81
0.81
0.81
0.81
0.81
0.81
0.81
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
1.16
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
0.46
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
4.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
8.0
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
Q1
250
3000
3000
250
3000
250
250
3000
3000
250
250
3000
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
7-Jul-2023
TAPE AND REEL BOX DIMENSIONS
Width (mm)
H
W
L
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TPS62800YKAR
TPS62801YKAR
TPS62801YKAR
TPS62801YKAT
TPS62801YKAT
TPS62802YKAR
TPS62802YKAR
TPS62802YKAT
TPS62806YKAR
TPS62806YKAT
TPS62806YKAT
TPS62807YKAR
TPS62807YKAR
TPS62807YKAT
TPS62807YKAT
TPS62808YKAR
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
YKA
YKA
YKA
YKA
YKA
YKA
YKA
YKA
YKA
YKA
YKA
YKA
YKA
YKA
YKA
YKA
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
6
3000
3000
3000
250
182.0
220.0
182.0
182.0
220.0
182.0
220.0
182.0
182.0
182.0
220.0
182.0
220.0
182.0
220.0
182.0
182.0
220.0
182.0
182.0
220.0
182.0
220.0
182.0
182.0
182.0
220.0
182.0
220.0
182.0
220.0
182.0
20.0
35.0
20.0
20.0
35.0
20.0
35.0
20.0
20.0
20.0
35.0
20.0
35.0
20.0
35.0
20.0
250
3000
3000
250
3000
250
250
3000
3000
250
250
3000
Pack Materials-Page 2
PACKAGE OUTLINE
YKA0006
DSBGA - 0.4 mm max height
SCALE 12.000
DIE SIZE BALL GRID ARRAY
A
B
E
BALL A1
INDEX AREA
D
0.40
0.35
C
SEATING PLANE
0.05 C
0.18
0.13
BALL
TYP
0.35 TYP
C
B
A
0.7
TYP
SYMM
D: Max = 1.084 mm, Min =1.024 mm
E: Max = 0.734 mm, Min =0.674 mm
0.35
TYP
1
2
0.24
6X
0.19
SYMM
0.015
C A B
4223607/B 06/2023
NanoFree Is a trademark of Texas Instruments.
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. NanoFreeTM package configuration.
www.ti.com
EXAMPLE BOARD LAYOUT
YKA0006
DSBGA - 0.4 mm max height
DIE SIZE BALL GRID ARRAY
(0.35) TYP
6X ( 0.2)
(0.35) TYP
1
2
A
B
SYMM
C
SYMM
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:50X
(
0.2)
0.0325 MAX
0.0325 MIN
METAL
UNDER
METAL
SOLDER MASK
EXSPOSED
EXPOSED
METAL
SOLDER MASK
OPENING
(
0.2)
METAL
SOLDER MASK
OPENING
NON-SOLDER MASK
DEFINED
SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK DETAILS
NOT TO SCALE
4223607/B 06/2023
NOTES: (continued)
4. Final dimensions may vary due to manufacturing tolerance considerations and also routing constraints.
For more information, see Texas Instruments literature number SNVA009 (www.ti.com/lit/snva009).
www.ti.com
EXAMPLE STENCIL DESIGN
YKA0006
DSBGA - 0.4 mm max height
DIE SIZE BALL GRID ARRAY
(0.35) TYP
6X ( 0.21)
(R0.05) TYP
1
2
A
(0.35) TYP
SYMM
B
METAL
TYP
C
SYMM
SOLDER PASTE EXAMPLE
BASED ON 0.075 mm - 0.1 mm THICK STENCIL
SCALE:50X
4223607/B 06/2023
NOTES: (continued)
5. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release.
www.ti.com
重要声明和免责声明
TI“按原样”提供技术和可靠性数据(包括数据表)、设计资源(包括参考设计)、应用或其他设计建议、网络工具、安全信息和其他资源,
不保证没有瑕疵且不做出任何明示或暗示的担保,包括但不限于对适销性、某特定用途方面的适用性或不侵犯任何第三方知识产权的暗示担
保。
这些资源可供使用 TI 产品进行设计的熟练开发人员使用。您将自行承担以下全部责任:(1) 针对您的应用选择合适的 TI 产品,(2) 设计、验
证并测试您的应用,(3) 确保您的应用满足相应标准以及任何其他功能安全、信息安全、监管或其他要求。
这些资源如有变更,恕不另行通知。TI 授权您仅可将这些资源用于研发本资源所述的 TI 产品的应用。严禁对这些资源进行其他复制或展示。
您无权使用任何其他 TI 知识产权或任何第三方知识产权。您应全额赔偿因在这些资源的使用中对 TI 及其代表造成的任何索赔、损害、成
本、损失和债务,TI 对此概不负责。
TI 提供的产品受 TI 的销售条款或 ti.com 上其他适用条款/TI 产品随附的其他适用条款的约束。TI 提供这些资源并不会扩展或以其他方式更改
TI 针对 TI 产品发布的适用的担保或担保免责声明。
TI 反对并拒绝您可能提出的任何其他或不同的条款。IMPORTANT NOTICE
邮寄地址:Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023,德州仪器 (TI) 公司
相关型号:
TPS62802YKAR
1.75-V to 5.5-V input, 1-A ultra-low IQ step-down converter in 0.7-mm x 1.05-mm chip scale package | YKA | 6 | -40 to 125
TI
TPS62802YKAT
1.75-V to 5.5-V input, 1-A ultra-low IQ step-down converter in 0.7-mm x 1.05-mm chip scale package | YKA | 6 | -40 to 125
TI
TPS62806YKAR
1.75-V to 5.5-V input, 600-mA ultra-low IQ step-down converter in 0.7-mm x 1.05-mm WCSP | YKA | 6 | -40 to 125
TI
TPS62806YKAT
1.75-V to 5.5-V input, 600-mA ultra-low IQ step-down converter in 0.7-mm x 1.05-mm WCSP | YKA | 6 | -40 to 125
TI
TPS62807YKAR
1.75-V to 5.5-V input, 600-mA ultra-low IQ step-down converter in 0.7-mm x 1.05-mm WCSP | YKA | 6 | -40 to 125
TI
TPS62807YKAT
1.75-V to 5.5-V input, 600-mA ultra-low IQ step-down converter in 0.7-mm x 1.05-mm WCSP | YKA | 6 | -40 to 125
TI
TPS62808YKAR
1.75-V to 5.5-V input, 600-mA ultra-low IQ step-down converter in 0.7-mm x 1.05-mm WCSP | YKA | 6 | -40 to 125
TI
©2020 ICPDF网 联系我们和版权申明