TPS63012YFF [TI]
HIGHLY EFFICIENT, SINGLE INDUCTOR BUCK-BOOST CONVERTER WITH 2-A SWITCHES; 高效率,单电感具有2 C开关降压 - 升压型转换器型号: | TPS63012YFF |
厂家: | TEXAS INSTRUMENTS |
描述: | HIGHLY EFFICIENT, SINGLE INDUCTOR BUCK-BOOST CONVERTER WITH 2-A SWITCHES |
文件: | 总28页 (文件大小:685K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TPS63010
TPS63011
TPS63012
www.ti.com ........................................................................................................................................................ SLVS653A–JUNE 2008–REVISED AUGUST 2009
HIGHLY EFFICIENT, SINGLE INDUCTOR BUCK-BOOST CONVERTER WITH 2-A
SWITCHES
1
FEATURES
DESCRIPTION
•
Up to 96% Efficiency
•
1200-mA Output Current at 3.3 V in Step Down
Mode (VIN = 3.6 V to 5.5 V)
The TPS6301x devices provide a power supply
solution for products powered by either a two-cell or
three-cell alkaline, NiCd or NiMH battery, or a
one-cell Li-Ion or Li-polymer battery. Output currents
can go as high as 1200 mA while using a single-cell
Li-Ion or Li-Polymer Battery, and discharge it down to
2.5 V or lower. The buck-boost converter is based on
a fixed frequency, pulse-width-modulation (PWM)
controller using synchronous rectification to obtain
maximum efficiency. At low load currents, the
converter enters Power Save mode to maintain high
efficiency over a wide load current range. The Power
Save mode can be disabled, forcing the converter to
operate at a fixed switching frequency. The maximum
average current in the switches is limited to a typical
value of 2200 mA. The output voltage is
programmable using an external resistor divider, or is
fixed internally on the chip. The converter can be
disabled to minimize battery drain. During shutdown,
the load is disconnected from the battery. The device
is packaged in a 20-pin WCSP package measuring
2.14 mm x 1.93 mm (YFF).
•
•
Up to 800-mA Output Current at 3.3 V in Boost
Mode (VIN > 2.4 V)
Automatic Transition between Step Down and
Boost Mode
•
•
•
Device Quiescent Current less than 50µA
Input Voltage Range: 2 V to 5.5 V
Fixed and Adjustable Output Voltage Options
from 1.2 V to 5.5 V
•
•
Power Save Mode for Improved Efficiency at
Low Output Power
Forced Fixed Frequency Operation and
Synchronization possible
•
•
•
•
Load Disconnect During Shutdown
Output Overvoltage Protection
Overtemperature Protection
Available in Small 20 pin 2.14 mm x 1.93 mm,
WCSP Package
Typical Application Circuit
L1
APPLICATIONS
1.5 µH
•
All Two-Cell and Three-Cell Alkaline, NiCd or
NiMH or Single-Cell Li Battery
Powered Products
L1
L2
V
OUT
V
VIN
VOUT
IN
1.8 V to
5.5 V
3.3 V
Up to
1200 mA
VINA
C1
C2
10 µ
•
•
•
•
•
Portable Audio Players
PDAs
Cellular Phones
Personal Medical Products
White LEDs
10 µF
F
EN
PS
FB
VSEL
SYNC
GND
PGND
TPS63011
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2008–2009, Texas Instruments Incorporated
TPS63010
TPS63011
TPS63012
SLVS653A–JUNE 2008–REVISED AUGUST 2009 ........................................................................................................................................................ www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
AVAILABLE OUTPUT VOLTAGE OPTIONS(1)
OUTPUT
PACKAGE
MARKING
OUTPUT VOLTAGE
DC/DC at VSEL = 1
VOLTAGE
DC/DC at
VSEL = 0
TA
PACKAGE
PART NUMBER(2)
Adjustable
3.3 V
Adjustable
2.8 V
TPS63010
TPS63011
TPS63012
TPS63010YFF
TPS63011YFF
TPS63012YFF
- 40°C to 85°C
20-Pin WCSP
3.4 V
2.9 V
(1) Contact the factory to check availability of other fixed output voltage versions.
(2) The YFF package is available taped and reeled. Add R suffix to device type (e.g., TPS63010YFFR) to order quantities of 3000 devices
per reel. Add T suffix to device type (e.g., TPS63010YFFT) to order quantities of 250 devices per reel.
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range (unless otherwise noted)(1)
TPS6301x
UNITS
VI
Input voltage range on VIN, VINA, VINA1, L1, L2, VOUT, PS, SYNC, VSEL,
EN, FB
– 0.3 to 7
V
TJ
Operating junction temperature range
Storage temperature range
– 40 to 150
°C
Tstg
– 65 to 150
(2)
Human Body Model (HBM)
2.5
150
1
kV
V
(2)
ESD Voltage
Machine Model (MM)
Charged Device Model (CDM)(2)
kV
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) ESD testing is performed according to the respective JESD22 JEDEC standard.
DISSIPATION RATINGS TABLE
THERMAL RESISTANCE
POWER RATING
DERATING FACTOR ABOVE
TA = 25°C
PACKAGE(1)
ΘJA
TA≤ 25°C
YFF
84 °C/W
1190 mW
12 mW/°C
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
RECOMMENDED OPERATING CONDITIONS
MIN
2
NOM
MAX UNIT
Supply voltage at VIN, VINA
5.5
85
V
Operating free air temperature range, TA
Operating junction temperature range, TJ
– 40
– 40
°C
°C
125
2
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS63010 TPS63011 TPS63012
TPS63010
TPS63011
TPS63012
www.ti.com ........................................................................................................................................................ SLVS653A–JUNE 2008–REVISED AUGUST 2009
ELECTRICAL CHARACTERISTICS
over recommended free-air temperature range and over recommended input voltage range (typical at an ambient temperature
range of 25°C) (unless otherwise noted)
DC/DC STAGE
PARAMETER
TEST CONDITIONS
MIN
2
TYP
MAX
5.5
UNIT
V
VI
Input voltage range
VI
Input voltage range for startup
TPS63010 output voltage range
TPS63010 feedback voltage
TPS63010 feedback voltage
TPS63011 output voltage
TPS63011 output voltage
TPS63011 output voltage
TPS63011 output voltage
TPS63012 output voltage
TPS63012 output voltage
TPS63012 output voltage
TPS63012 output voltage
Oscillator frequency
2.1
5.5
V
VO
VFB
VFB
1.2
5.5
V
0°C ≤ TA ≤ 60°C
492.5
489
500
500
2.8
503.5
507
mV
mV
V
VSEL = LOW, 0°C ≤ TA ≤ 60°C
VSEL = LOW
2.758
2.750
3.251
3.241
2.857
2.848
3.349
3.339
2200
2200
2000
2.842
2.850
3.350
3.359
2.944
2.952
3.451
3.461
2600
3000
2400
2.8
V
VSEL = HIGH, 0°C ≤ TA ≤ 60°C
VSEL = HIGH
3.3
V
3.3
V
VSEL = LOW, 0°C ≤ TA ≤ 60°C
VSEL = LOW
2.9
V
2.9
V
VSEL = HIGH, 0°C ≤ TA ≤ 60°C
VSEL = HIGH
3.4
V
3.4
V
f
2400
kHz
kHz
mA
mΩ
mΩ
Frequency range for synchronization
Switch current limit
ISW
VIN = VINA = 3.6 V, TA = 25°C
VIN = VINA = 3.6 V
VIN = VINA = 3.6 V
PS = HIGH
2200
100
100
0.5%
0.5%
1
High side switch on resistance
Low side switch on resistance
Maximum line regulation
Maximum load regulation
VIN
PS = HIGH
2
µA
µA
VINA
40
50
IO = 0 mA, VEN = VIN = VINA = 3.6 V,
VOUT = 3.3 V
VOUT
Iq
Quiescent current
(adjustable
output voltage
version)
4
6
µA
FB input impedance (fixed output
voltage versions)
1
MΩ
VIN
VEN = 0 V, VIN = VINA = 3.6 V
PS, SYNC, VSEL clamped on GND or
VINA
0.1
0.1
1
µA
µA
IS
Shutdown current
VINA
1.5
CONTROL STAGE
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
UVLO
Undervoltage lockout threshold
VINA voltage decreasing
1.5
1.7
1.8
0.4
V
V
EN, PS, SYNC, VSEL input low
voltage
VIL
EN, PS, SYNC, VSEL input high
voltage
1.2
V
VIH
EN, PS, SYNC, VSEL input current
Output overvoltage protection
Overtemperature protection
Overtemperature hysteresis
Clamped on GND or VINA
0.01
6.5
140
20
0.1
µA
V
°C
°C
Copyright © 2008–2009, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Link(s): TPS63010 TPS63011 TPS63012
TPS63010
TPS63011
TPS63012
SLVS653A–JUNE 2008–REVISED AUGUST 2009 ........................................................................................................................................................ www.ti.com
PIN ASSIGNMENTS
YFF PACKAGE
(TOP VIEW)
A4
A3
A2
A1
B4
B3
B2
B1
C4
C3
C2
C1
D4
D3
D2
D1
E4
E3
E2
E1
Pin Functions
PIN
I/O
DESCRIPTION
NAME
NO.
EN
A4
I
I
Enable input. (1 enabled, 0 disabled)
Voltage feedback of adjustable versions, must be connected to VOUT at fixed output
voltage versions
FB
E3
GND
PS
C3, D3, E4
C4
Control / logic ground
I
I
I
Enable / disable power save mode (1 disabled, 0 enabled)
Connection for Inductor
L1
B1,B2
D1,D2
C1,C2
B4
L2
Connection for Inductor
PGND
SYNC
Power ground
I
I
Clock signal for synchronization, should be connected to GND if not used
Output voltage select for fixed output voltage options (1 programs higher output voltage
option, 0 programs lower output voltage option), must be connected to a defined logic
signal at adjustable output voltage option.
VSEL
D4
VIN
A1, A2
A3
I
Supply voltage for power stage
VINA
VINA1
VOUT
I
Supply voltage for control stage
Output of the 100 Ω for designing the VINA filter
Buck-boost converter output
B3
O
O
E1,E2
4
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS63010 TPS63011 TPS63012
TPS63010
TPS63011
TPS63012
www.ti.com ........................................................................................................................................................ SLVS653A–JUNE 2008–REVISED AUGUST 2009
FUNCTIONAL BLOCK DIAGRAM (TPS63010)
L1
L2
VIN
VOUT
Current
Sensor
VINA1
PGND PGND
VIN
Gate
VOUT
Control
_
+
Modulator
Oscillator
+
_
VINA
FB
VREF
PS
+
−
SYNC
Device
Control
VSEL
EN
Temperature
Control
PGND
PGND
GND
FUNCTIONAL BLOCK DIAGRAM (TPS63011, TPS63012)
L1
L2
VIN
VOUT
Current
Sensor
VINA1
PGND PGND
VIN
Gate
FB
VOUT
Control
VSEL
_
+
Modulator
Oscillator
+
_
VINA
PS
+
−
SYNC
VREF
Device
Control
VSEL
EN
Temperature
Control
PGND
PGND
GND
Copyright © 2008–2009, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Link(s): TPS63010 TPS63011 TPS63012
TPS63010
TPS63011
TPS63012
SLVS653A–JUNE 2008–REVISED AUGUST 2009 ........................................................................................................................................................ www.ti.com
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
vs Input voltage (TPS63010, VOUT = 2.5 V / VOUT = 4.5 V)
vs Input voltage (TPS63011, VSEL = HIGH / VSEL = LOW)
vs Input voltage (TPS63012, VSEL = HIGH / VSEL = LOW)
1
2
3
Maximum output current
vs Output current (TPS63010, Power Save Enabled, VOUT = 2.5 V / VOUT
= 4.5 V)
4
vs Output current (TPS63010, Power Save Disabled, VOUT = 2.5V / VOUT
= 4.5V)
5
vs Output current (TPS63011, Power Save Enabled, VSEL = HIGH / VSEL
= LOW)
6
vs Output current (TPS63011, Power Save Disabled, VSEL = HIGH / VSEL
= LOW)
7
vs Output current (TPS63012, Power Save Enabled, VSEL = HIGH / VSEL
= LOW)
8
vs Output current (TPS63012, Power Save Disabled, VSEL = HIGH / VSEL
= LOW)
9
vs Input voltage (TPS63010, Power Save Enabled, VOUT = 2.5V, IOUT =
{10; 100; 500; 1000 mA})
10
11
12
13
14
15
16
17
18
19
20
21
vs Input voltage (TPS63010, Power Save Enabled, VOUT = 4.5V, IOUT =
{10; 100; 500; 1000 mA})
vs Input voltage (TPS63010, Power Save Disabled, VOUT = 2.5V, IOUT =
{10; 100; 500; 1000 mA})
Efficiency
vs Input voltage (TPS63010, Power Save Disabled, VOUT = 4.5V, IOUT =
{10; 100; 500; 1000 mA})
vs Input voltage (TPS63011, Power Save Enabled, VSEL = HIGH, IOUT =
{10; 100; 500; 1000 mA})
vs Input voltage (TPS63011, Power Save Enabled, VSEL = LOW, IOUT =
{10; 100; 500; 1000 mA})
vs Input voltage (TPS63011, Power Save Disabled, VSEL = HIGH, IOUT =
{10; 100; 500; 1000 mA})
vs Input voltage (TPS63011, Power Save Disabled, VSEL = LOW, IOUT =
{10; 100; 500; 1000 mA})
vs Input voltage (TPS63012, Power Save Enabled, VSEL = HIGH, IOUT =
{10; 100; 500; 1000 mA})
vs Input voltage (TPS63012, Power Save Enabled, VSEL = LOW, IOUT =
{10; 100; 500; 1000 mA})
vs Input voltage (TPS63012, Power Save Disabled, VSEL = HIGH, IOUT =
{10; 100; 500; 1000 mA})
vs Input voltage (TPS63012, Power Save Disabled, VSEL = LOW, IOUT =
{10; 100; 500; 1000 mA})
Load transient response (TPS63011, VIN < VOUT, VSEL = HIGH)
Load transient response (TPS63011, VIN > VOUT, VSEL = HIGH)
Load transient response (TPS63012, VIN < VOUT, VSEL = HIGH)
Load transient response (TPS63012, VIN > VOUT, VSEL = HIGH)
Line transient response (TPS63011, VSEL = HIGH, Iout = 300 mA)
Line transient response (TPS63012, VSEL = HIGH, Iout = 300 mA)
Startup after enable (TPS63011, VSEL = HIGH)
22
23
24
25
26
27
28
29
Waveforms
Startup after enable (TPS63012, VSEL = HIGH)
6
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS63010 TPS63011 TPS63012
TPS63010
TPS63011
TPS63012
www.ti.com ........................................................................................................................................................ SLVS653A–JUNE 2008–REVISED AUGUST 2009
MAXIMUM OUTPUT CURRENT
MAXIMUM OUTPUT CURRENT
vs
vs
INPUT VOLTAGE
(TPS63010)
INPUT VOLTAGE
(TPS63011)
2500
2250
2000
1750
1500
1250
1000
750
2500
2250
2000
1750
1500
1250
1000
750
V
O
= 2.8 V
V
O
= 2.5 V
V
O
= 3.3 V
V
O
= 4.5 V
500
500
250
250
0
2.0
0
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
2.5
3.0
3.5
4.0
4.5
5.0
5.5
V − Input Voltage − V
I
V − Input Voltage − V
I
G001
G002
Figure 1.
Figure 2.
MAXIMUM OUTPUT CURRENT
EFFICIENCY
vs
OUTPUT CURRENT
(TPS63010)
vs
INPUT VOLTAGE
(TPS63012)
2500
2250
2000
1750
1500
1250
1000
750
100
90
80
70
60
50
40
30
20
10
0
V = 3.6 V, V = 2.5 V
V
O
= 2.9 V
I
O
V = 2.4 V, V = 2.5 V
I
O
V
= 3.4 V
O
V = 3.6 V, V = 4.5 V
I
O
V = 2.4 V, V = 4.5 V
I
O
500
250
Power-Save Mode Enabled
100 1k 10k
0
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
0.1
1
10
V − Input Voltage − V
I
I
O
− Output Current − mA
G003
G004
Figure 3.
Figure 4.
Copyright © 2008–2009, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Link(s): TPS63010 TPS63011 TPS63012
TPS63010
TPS63011
TPS63012
SLVS653A–JUNE 2008–REVISED AUGUST 2009 ........................................................................................................................................................ www.ti.com
EFFICIENCY
vs
OUTPUT CURRENT
(TPS63010)
EFFICIENCY
vs
OUTPUT CURRENT
(TPS63011)
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
V = 3.6 V, V = 2.8 V
I
O
V = 2.4 V, V = 2.5 V
I
O
V = 2.4 V, V = 2.8 V
I
O
V = 2.4 V,
I
V
O
= 4.5 V
V = 2.4 V, V = 3.3 V
I
V = 3.6 V,
O
I
V
O
= 4.5 V
V = 3.6 V, V = 3.3 V
I
O
V = 3.6 V, V = 2.5 V
I
O
Power-Save Mode Disabled
10 100 1k
Power-Save Mode Enabled
100 1k 10k
0.1
1
10k
0.1
1
10
I
O
− Output Current − mA
I
O
− Output Current − mA
G005
G006
Figure 5.
Figure 6.
EFFICIENCY
vs
OUTPUT CURRENT
(TPS63011)
EFFICIENCY
vs
OUTPUT CURRENT
(TPS63012)
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
V = 3.6 V, V = 2.9 V
I
O
V = 2.4 V, V = 2.8 V
I
O
V = 3.6 V, V = 3.3 V
I
O
V = 2.4 V, V = 2.9 V
I
O
V = 2.4 V, V = 3.4 V
I
O
V = 3.6 V, V = 2.8 V
I
O
V = 3.6 V, V = 3.4 V
I
O
V = 2.4 V, V = 3.3 V
I
O
Power-Save Mode Disabled
10 100 1k
Power-Save Mode Enabled
100 1k 10k
0.1
1
10k
0.1
1
10
I
O
− Output Current − mA
I
O
− Output Current − mA
G007
G008
Figure 7.
Figure 8.
8
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS63010 TPS63011 TPS63012
TPS63010
TPS63011
TPS63012
www.ti.com ........................................................................................................................................................ SLVS653A–JUNE 2008–REVISED AUGUST 2009
EFFICIENCY
vs
OUTPUT CURRENT
(TPS63012)
EFFICIENCY
vs
INPUT VOLTAGE
(TPS63010)
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
V = 2.4 V, V = 2.9 V
I
O
I
= 1000 mA
O
V = 2.4 V, V = 3.4 V
I
O
I
= 100 mA
O
I
O
= 500 mA
I
= 10 mA
O
V = 3.6 V, V = 2.9 V
I
O
V = 3.6 V, V = 3.4 V
I
O
V
O
= 2.5 V
Power-Save Mode Disabled
Power-Save Mode Enabled
0.1
1
10
100
1k
10k
2.0
2.5 3.0 3.5 4.0
4.5
5.0
5.5
I
O
− Output Current − mA
V − Input Voltage − V
I
G009
G010
Figure 9.
Figure 10.
EFFICIENCY
vs
INPUT VOLTAGE
(TPS63010)
EFFICIENCY
vs
INPUT VOLTAGE
(TPS63010)
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
I
= 500 mA
I
= 100 mA
O
O
I
= 1000 mA
O
I
O
= 1000 mA
I
= 100 mA
O
I
= 10 mA
O
I
O
= 500 mA
I
= 10 mA
O
V
= 4.5 V
V
= 2.5 V
Power-Save Mode Disabled
O
O
Power-Save Mode Enabled
2.0
2.5 3.0 3.5 4.0
4.5
5.0
5.5
2.0
2.5 3.0 3.5 4.0
4.5
5.0
5.5
V − Input Voltage − V
I
V − Input Voltage − V
I
G011
G012
Figure 11.
Figure 12.
Copyright © 2008–2009, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Link(s): TPS63010 TPS63011 TPS63012
TPS63010
TPS63011
TPS63012
SLVS653A–JUNE 2008–REVISED AUGUST 2009 ........................................................................................................................................................ www.ti.com
EFFICIENCY
vs
INPUT VOLTAGE
(TPS63010)
EFFICIENCY
vs
INPUT VOLTAGE
(TPS63011)
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
I
= 100 mA
O
I
= 1000 mA
I
= 500 mA
O
O
I
O
= 1000 mA
I
= 100 mA
O
I
= 10 mA
I
= 500 mA
O
O
I
= 10 mA
O
V
O
= 4.5 V
Power-Save Mode Disabled
V
= 3.3 V
O
Power-Save Mode Enabled
2.0
2.5 3.0 3.5 4.0
4.5
5.0
5.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
V − Input Voltage − V
I
V − Input Voltage − V
I
G013
G014
Figure 13.
Figure 14.
EFFICIENCY
vs
INPUT VOLTAGE
(TPS63011)
EFFICIENCY
vs
INPUT VOLTAGE
(TPS63011)
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
I
= 100 mA
O
I
= 500 mA
I
= 100 mA
I = 1000 mA
O
O
O
I
= 1000 mA
O
I
O
= 500 mA
I
= 10 mA
O
I
= 10 mA
O
V
O
= 2.8 V
V
= 3.3 V
Power-Save Mode Disabled
O
Power-Save Mode Enabled
2.0
2.5 3.0 3.5 4.0
4.5
5.0
5.5
2.0
2.5 3.0 3.5 4.0
4.5
5.0
5.5
V − Input Voltage − V
I
V − Input Voltage − V
I
G015
G016
Figure 15.
Figure 16.
10
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS63010 TPS63011 TPS63012
TPS63010
TPS63011
TPS63012
www.ti.com ........................................................................................................................................................ SLVS653A–JUNE 2008–REVISED AUGUST 2009
EFFICIENCY
vs
INPUT VOLTAGE
(TPS63011)
EFFICIENCY
vs
INPUT VOLTAGE
(TPS63012)
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
I
= 100 mA
I
= 500 mA
O
O
I
= 1000 mA
O
I
= 100 mA
O
I
O
= 1000 mA
I
= 10 mA
I
O
= 500 mA
O
I
= 10 mA
O
V
O
= 2.8 V
Power-Save Mode Disabled
V = 3.4 V
O
Power-Save Mode Enabled
2.0
2.5 3.0 3.5 4.0
4.5
5.0
5.5
2.0
2.5 3.0 3.5 4.0
4.5
5.0
5.5
V − Input Voltage − V
I
V − Input Voltage − V
I
G017
G018
Figure 17.
Figure 18.
EFFICIENCY
vs
INPUT VOLTAGE
(TPS63012)
EFFICIENCY
vs
INPUT VOLTAGE
(TPS63012)
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
I
= 100 mA
O
I
= 500 mA
O
I
= 100 mA
O
I = 1000 mA
O
I
= 1000 mA
O
I
= 10 mA
O
I
O
= 500 mA
I
= 10 mA
O
V
O
= 2.9 V
V = 3.4 V
O
Power-Save Mode Disabled
Power-Save Mode Enabled
2.0
2.5 3.0 3.5 4.0
4.5
5.0
5.5
2.0
2.5 3.0 3.5 4.0
4.5
5.0
5.5
V − Input Voltage − V
I
V − Input Voltage − V
I
G019
G020
Figure 19.
Figure 20.
Copyright © 2008–2009, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Link(s): TPS63010 TPS63011 TPS63012
TPS63010
TPS63011
TPS63012
SLVS653A–JUNE 2008–REVISED AUGUST 2009 ........................................................................................................................................................ www.ti.com
EFFICIENCY
vs
INPUT VOLTAGE
(TPS63012)
100
90
80
I
= 100 mA
O
I
= 500 mA
= 10 mA
O
70
60
50
40
30
20
10
0
I
O
= 1000 mA
I
O
V
O
= 2.9 V
Power-Save Mode Disabled
2.0
2.5 3.0 3.5 4.0
4.5
5.0
5.5
V − Input Voltage − V
I
G021
Figure 21.
LOAD TRANSIENT RESPONSE
(TPS63011)
VI = 2.4 V, IO = 80 mA to 750 mA
Output Voltage
200 mV/div, AC
Output Current
500 mA/div
TPS63011, VO = 3.3 V
Timebase 1 ms/div
Figure 22.
G028
12
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS63010 TPS63011 TPS63012
TPS63010
TPS63011
TPS63012
www.ti.com ........................................................................................................................................................ SLVS653A–JUNE 2008–REVISED AUGUST 2009
LOAD TRANSIENT RESPONSE
(TPS63011)
VI = 4.2 V, IO = 150 mA to 1300 mA
Output Voltage
200 mV/div, AC
Output Current
500 mA/div
TPS63011, VO = 3.3 V
Timebase 1 ms/div
G029
Figure 23.
LOAD TRANSIENT RESPONSE
(TPS63012)
VI = 2.4 V, IO = 80 mA to 630 mA
Output Voltage
200 mV/div, AC
Output Current
500 mA/div
TPS63012, VO = 3.4 V
Timebase 1 ms/div
G030
Figure 24.
Copyright © 2008–2009, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Link(s): TPS63010 TPS63011 TPS63012
TPS63010
TPS63011
TPS63012
SLVS653A–JUNE 2008–REVISED AUGUST 2009 ........................................................................................................................................................ www.ti.com
LOAD TRANSIENT RESPONSE
(TPS63012)
VI = 4.2 V, IO = 140 mA to 1100 mA
Output Voltage
200 mV/div, AC
Output Current
500 mA/div
TPS63012, VO = 3.4 V
Timebase 1 ms/div
G031
Figure 25.
LINE TRANSIENT RESPONSE
(TPS63011)
VI = 3 V to 3.6 V, IO = 300 mA
Input Voltage
500 mV/div, AC
Output Voltage
20 mV/div, AC
TPS63011, VO = 3.3 V
Timebase 2 ms/div
G032
Figure 26.
14
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS63010 TPS63011 TPS63012
TPS63010
TPS63011
TPS63012
www.ti.com ........................................................................................................................................................ SLVS653A–JUNE 2008–REVISED AUGUST 2009
LINE TRANSIENT RESPONSE
(TPS63012)
VI = 3 V to 3.6V, IO = 300 mA
Input Voltage
500 mV/div, AC
Output Voltage
10 mV/div, AC
TPS63012, VO = 3.4 V
Timebase 2 ms/div
G033
Figure 27.
START-UP AFTER ENABLE
(TPS63011)
Enable
Output Voltage
5 V/div, DC
1 V/div, DC
Inductor Current
500 mA/div, DC
Voltage at L1
2 V/div, DC
VI = 4.2 V, RL = 11 W
TPS63011, VO = 3.3 V
Timebase 100 ms/div
G034
Figure 28.
Copyright © 2008–2009, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Link(s): TPS63010 TPS63011 TPS63012
TPS63010
TPS63011
TPS63012
SLVS653A–JUNE 2008–REVISED AUGUST 2009 ........................................................................................................................................................ www.ti.com
START-UP AFTER ENABLE
(TPS63012)
Output Voltage
Enable
1 V/div, DC
5 V/div, DC
Inductor Current
500 mA/div, DC
Voltage at L1
2 V/div, DC
VI = 4.2 V, RL = 11 W
TPS63012, VO = 3.4 V
Timebase 100 ms/div
G035
Figure 29.
PARAMETER MEASUREMENT INFORMATION
L1
L1
L2
V
OUT
V
IN
VIN
VOUT
R1
R2
VINA1
VINA
C1
C2
C3
FB
EN
PS
VSEL
SYNC
GND
PGND
TPS6301X
List of Components
REFERENCE
DESCRIPTION
MANUFACTURER
Texas Instruments
Coilcraft
TPS6301 0 / 1 / 2
LPS3015-222
L1
C1
GRM188R60J106M (10 µF 6.3V,
Murata
0603)
C2
2 × GRM188R60J106M (10 µF 6.3V, Murata
0603)
C3
0.1 µF, X7R ceramic
R1, R2
Depending on the output voltage at TPS63010, not used at TPS6301 1 / 2 (R1 shorted)
16
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS63010 TPS63011 TPS63012
TPS63010
TPS63011
TPS63012
www.ti.com ........................................................................................................................................................ SLVS653A–JUNE 2008–REVISED AUGUST 2009
DETAILED DESCRIPTION
CONTROLLER CIRCUIT
The controlling circuit of the device is based on an average current mode topology. The average inductor current
is regulated by a fast current regulator loop which is controlled by a voltage control loop. The controller also uses
input and output voltage feedforward. Changes of input and output voltage are monitored and immediately can
change the duty cycle in the modulator to achieve a fast response to those errors. The voltage error amplifier
gets its feedback input from the FB pin. At adjustable output voltages a resistive voltage divider must be
connected to that pin. At fixed output voltages FB must be connected to the output voltage to directly sense the
voltage. Fixed output voltage versions use a trimmed internal resistive divider. The feedback voltage will be
compared with the internal reference voltage to generate a stable and accurate output voltage.
The controller circuit also senses the average input current as well as the peak input current. With this, maximum
input power can be controlled as well as the maximum peak current to achieve a safe and stable operation under
all possible conditions. To finally protect the device from overheating, an internal temperature sensor is
implemented.
Synchronous Operation
The device uses 4 internal N-channel MOSFETs to maintain synchronous power conversion at all possible
operating conditions. This enables the device to keep high efficiency over a wide input voltage and output power
range.
To avoid ground shift problems due to the high currents in the switches, two separate ground pins GND and
PGND are used. The reference for all control functions is the GND pin. The power switches are connected to
PGND. Both grounds must be connected on the PCB at only one point ideally close to the GND pin. Due to the
4-switch topology, the load is always disconnected from the input during shutdown of the converter.
Buck-Boost Operation
To be able to regulate the output voltage properly at all possible input voltage conditions, the device
automatically switches from step down operation to boost operation and back as required by the configuration. It
always uses one active switch, one rectifying switch, one switch permanently on, and one switch permanently off.
Therefore, it operates as a step down converter (buck) when the input voltage is higher than the output voltage,
and as a boost converter when the input voltage is lower than the output voltage. There is no mode of operation
in which all 4 switches are permanently switching. Controlling the switches this way allows the converter to
maintain high efficiency at the most important point of operation; when input voltage is close to the output
voltage. The RMS current through the switches and the inductor is kept at a minimum, to minimize switching and
conduction losses. Switching losses are also kept low by using only one active and one passive switch.
Regarding the remaining 2 switches, one is kept permanently on and the other is kept permanently off, thus
causing no switching losses.
Power Save Mode
The PS pin can be used to select different operation modes. To enable power save, PS must be set low. Power
save mode is used to improve efficiency at light load. If power save mode is enabled, the converter stops
operating if the average inductor current gets lower than about 300 mA and the output voltage is at or above its
nominal value. If the output voltage decreases below its nominal value, the device ramps up the output voltage
again by starting operation using a programmed average inductor current higher than required by the current
load condition. Operation can last for one or several pulses. The converter again stops operating once the
conditions for stopping operation are met again.
The power save mode can be disabled by programming high at PS. The PS input supports standard logic
threshold voltages. If the device is synchronized to an external clock connected to SYNC, power save mode is
disabled.
Copyright © 2008–2009, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Link(s): TPS63010 TPS63011 TPS63012
TPS63010
TPS63011
TPS63012
SLVS653A–JUNE 2008–REVISED AUGUST 2009 ........................................................................................................................................................ www.ti.com
Synchronization
Connecting a clock signal at SYNC forces the device to synchronize to the connected clock frequency.
Synchronization is done by a PLL, so synchronizing to lower and higher frequencies compared to the internal
clock works without any issues. The PLL can also tolerate missing clock pulses without the converter
malfunctioning. The SYNC input supports standard logic thresholds. If synchronization is not used SYNC must
be tied low or connected to GND. Applying a clock signal to SYNC automatically disables the power save mode.
Device Enable
The device is put into operation when EN is set high. It is put into a shutdown mode when EN is set to GND. In
shutdown mode, the regulator stops switching, all internal control circuitry is switched off, and the load is
disconnected from the input. This also means that the output voltage can drop below the input voltage during
shutdown. During start-up of the converter, the duty cycle and the peak current are limited in order to avoid high
peak currents flowing from the input.
Output Voltage Selection
To program the output voltage at an adjustable device option, like TPS63010 an external resistive feedback
divider, connected to FB must be used. For the fixed output voltage versions, FB is used as an output voltage
sense and must be connected to the output voltage VOUT. All fixed output voltage versions have two different
output voltages programmed internally. They are selected by programming high or low at VSEL. The higher
output voltage is selected by programming VSEL high and the lower output voltage is selected by programming
VSEL low. VSEL also supports standard logic thresholds.
Softstart and Short-Circuit Protection
After being enabled, the device starts operating. The average current limit ramps up from an initial 400 mA
following the output voltage increasing. At an output voltage of about 1.2 V, the current limit is at its nominal
value. If the output voltage does not increase, the current limit will not increase. There is no timer implemented.
Thus, the output voltage overshoot at startup, as well as the inrush current, is kept at a minimum. The device
ramps up the output voltage in a controlled manner even if a very large capacitor is connected at the output.
When the output voltage does not increase above 1.2 V, the device assumes a short-circuit at the output, and
keeps the current limit low to protect itself and the application. At a short at the output during operation, the
current limit is also decreased accordingly. At 0 V at the output, for example, the output current will not exceed
about 400 mA.
Undervoltage Lockout
If the supply voltage on VINA is lower than its approximate threshold (see electrical characteristics table), an
undervoltage lockout function prevents device start-up. When in operation, the device automatically enters the
shutdown mode if the voltage on VINA drops below the undervoltage lockout threshold. The device automatically
restarts if the input voltage recovers to the minimum operating input voltage.
Overvoltage Protection
If, for any reason, the output voltage is not fed back properly to the input of the voltage amplifier, control of the
output voltage will not work anymore. Therefore overvoltage protection is implemented to avoid the output
voltage exceeding critical values for the device and possibly for the system it is supplying. The implemented
overvoltage protection circuit monitors the output voltage internally as well. In case it reaches the overvoltage
threshold the voltage amplifier regulates the output voltage to this value.
Overtemperature Protection
The device has a built-in temperature sensor which monitors the internal IC temperature. If the temperature
exceeds the programmed threshold (see electrical characteristics table), the device stops operating. As soon as
the IC temperature has decreased below the programmed threshold, it again starts operating. There is a built-in
hysteresis to avoid unstable operation at IC temperatures at the overtemperature threshold.
18
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS63010 TPS63011 TPS63012
TPS63010
TPS63011
TPS63012
www.ti.com ........................................................................................................................................................ SLVS653A–JUNE 2008–REVISED AUGUST 2009
APPLICATION INFORMATION
DESIGN PROCEDURE
The TPS6301x dc/dc converters are intended for systems powered by one-cell Li-Ion or Li-Polymer battery with a
typical voltage between 2.3 V and 4.5 V. They can also be used in systems powered by a double or triple cell
Alkaline, NiCd, or NiMH battery with a typical terminal voltage between 2 V and 5.5 V . Additionally, any other
voltage source with a typical output voltage between 2 V and 5.5 V can power systems where the TPS6301x is
used.
PROGRAMMING THE OUTPUT VOLTAGE
Within the TPS6301X family there are fixed and adjustable output voltage versions available. To properly
configure the fixed output voltage devices, the FB pin is used to sense the output voltage. This means that it
must be connected directly to VOUT. At the adjustable output voltage versions, an external resistor divider is used
to adjust the output voltage. The resistor divider must be connected between VOUT, FB and GND. When the
output voltage is regulated properly, the typical value of the voltage at the FB pin is 500 mV. The maximum
recommended value for the output voltage is 5.5 V. The current through the resistive divider should be about 100
times greater than the current into the FB pin. The typical current into the FB pin is 0.01 µA, and the voltage
across the resistor between FB and GND, R2, is typically 500 mV. Based on those two values, the
recommended value for R2 should be lower than 500 kΩ, in order to set the divider current at 1 µA or higher.
The recommended value for this resistor is in the range of 200 kΩ. From that, the value of the resistor connected
between VOUT and FB, R1, depending on the needed output voltage (VOUT), is calculated using Equation 1:
V
OUT
ǒ Ǔ
R + R
* 1
1
2
V
FB
(1)
As an example, if an output voltage of 3.3 V is needed, a 1-MΩ resistor should be chosen for R1 if R2 is 180-kΩ.
L1
L1
L2
V
OUT
V
IN
VIN
VOUT
R1
R2
VINA1
VINA
C1
C2
C3
FB
EN
PS
VSEL
SYNC
GND
PGND
TPS6301X
Figure 30. Typical Application Circuit for Adjustable Output Voltage Option
INDUCTOR SELECTION
To properly configure the TPS6301X devices, an inductor must be connected between pin L1 and pin L2. To
estimate the inductance value Equation 2 and Equation 3 can be used.
μs
L1
=
VIN1 - VOUT × 0.5 ×
(
)
A
(2)
(3)
μs
A
L2 = VOUT × 0.5 ×
In Equation 2 the minimum inductance value, L1 for step down mode operation is calculated. VIN1 is the
Copyright © 2008–2009, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Link(s): TPS63010 TPS63011 TPS63012
TPS63010
TPS63011
TPS63012
SLVS653A–JUNE 2008–REVISED AUGUST 2009 ........................................................................................................................................................ www.ti.com
maximum input voltage. In Equation 3 the minimum inductance, L2, for boost mode operation is calculated. The
recommended minimum inductor value is either L1 or L2 whichever is higher. As an example, a suitable inductor
for generating 3.3 V from a Li-Ion battery with a battery voltage range from 2.5 V up to 4.2 V is 2.2 µH. The
recommended inductor value range is between 1 µH and 4.7 µH. In general, this means that at high voltage
conversion rates, higher inductor values offer better performance.
With the chosen inductance value, the peak current for the inductor in steady state operation can be calculated.
Equation 4 shows how to calculate the peak current I1 in step down mode operation and Equation 5 shows how
to calculate the peak current I2 in boost mode operation. VIN2 is the minimum input voltage.
OUTǒVIN1 OUTǓ
V
* V
I
OUT
0.8
I +
)
1
2 V
f L
IN1
(4)
ǒV
IN2Ǔ
V
* V
V
I
IN2
OUT
f L
OUT
0.8 V
OUT
I +
)
2
2 V
IN2
OUT
(5)
The critical current value for selecting the right inductor is the higher value of I1 and I2. It also needs to be taken
into account that load transients and error conditions may cause higher inductor currents. This also needs to be
taken into account when selecting an appropriate inductor. The following inductor series from different suppliers
have been used with TPS6301x converters:
Table 1. List of Inductors
VENDOR
Coilcraft
FDK
INDUCTOR SERIES
LPS3015
LPS4012
MIPSA2520
LQH3NP
Murata
Toko
LQM2HP
FDSE0312
CAPACITOR SELECTION
Input Capacitor
At least a 4.7-µF input capacitor is recommended to improve transient behavior of the regulator and EMI
behavior of the total power supply circuit. A ceramic capacitor placed as close as possible to the VIN and PGND
pins of the IC is recommended.
Output Capacitor
For the output capacitor, it is recommended to use small ceramic capacitors placed as close as possible to the
VOUT and PGND pins of the IC. If, for any reason, the application requires the use of large capacitors which can
not be placed close to the IC, using a smaller ceramic capacitor in parallel to the large one is recommended.
This small capacitor should be placed as close as possible to the VOUT and PGND pins of the IC.
To get an estimate of the recommended minimum output capacitance, Equation 6 can be used.
mF
mH
C
+ 5 L
OUT
(6)
A capacitor with a value in the range of the calculated minimum should be used. This is required to maintain
control loop stability. There are no additional requirements regarding minimum ESR. There is also no upper limit
for the output capacitance value. Larger capacitors will cause lower output voltage ripple as well as lower output
voltage drop during load transients.
20
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS63010 TPS63011 TPS63012
TPS63010
TPS63011
TPS63012
www.ti.com ........................................................................................................................................................ SLVS653A–JUNE 2008–REVISED AUGUST 2009
LAYOUT CONSIDERATIONS
As for all switching power supplies, the layout is an important step in the design, especially at high peak currents
and high switching frequencies. If the layout is not carefully done, the regulator could show stability problems as
well as EMI problems. Therefore, use wide and short traces for the main current path and for the power ground
tracks. The input capacitor, output capacitor, and the inductor should be placed as close as possible to the IC.
Use a common ground node for power ground and a different one for control ground to minimize the effects of
ground noise. Connect these ground nodes at any place close to one of the ground pins of the IC.
The feedback divider should be placed as close as possible to the control ground pin of the IC. To lay out the
control ground, it is recommended to use short traces, separated from the power ground traces. This avoids
ground shift problems, which can occur due to superimposition of power ground current and control ground
current.
R2
VOUT
VIN
L
Figure 31. PCB Layout Suggestion
Copyright © 2008–2009, Texas Instruments Incorporated
Submit Documentation Feedback
21
Product Folder Link(s): TPS63010 TPS63011 TPS63012
TPS63010
TPS63011
TPS63012
SLVS653A–JUNE 2008–REVISED AUGUST 2009 ........................................................................................................................................................ www.ti.com
THERMAL INFORMATION
Implementation of integrated circuits in low-profile and fine-pitch surface-mount packages typically requires
special attention to power dissipation. Many system-dependent issues such as thermal coupling, airflow, added
heat sinks and convection surfaces, and the presence of other heat-generating components affect the
power-dissipation limits of a given component.
Three basic approaches for enhancing thermal performance are listed below.
1. Improving the power dissipation capability of the PCB design
2. Improving the thermal coupling of the component to the PCB by soldering all pins to traces as wide as
possible.
3. Introducing airflow in the system
The maximum recommended junction temperature (TJ) of the TPS6301x devices is 125°C. The thermal
resistance of this 20-pin chipscale package (YFF) is RθJA = 84°C/W, if all pins are soldered. Specified regulator
operation is assured to a maximum ambient temperature TA of 85°C. Therefore, the maximum power dissipation
is about 476 mW, as calculated in Equation 7. More power can be dissipated if the maximum ambient
temperature of the application is lower.
T
* T
J(MAX)
R
A
125°C * 85°C
84 °CńW
P
+
+
+ 476 mW
D(MAX)
qJA
(7)
PACKAGE INFORMATION
Package Dimensions
The package dimensions for this YFF package are shown in the table below. See the package drawing at the
end of this data sheet for more details.
YFF Package Dimensions
Packaged Devices
D
E
TPS63010YFF
2.14 ± 0.05 mm
1.93 ± 0.05 mm
22
Submit Documentation Feedback
Copyright © 2008–2009, Texas Instruments Incorporated
Product Folder Link(s): TPS63010 TPS63011 TPS63012
TPS63010
TPS63011
TPS63012
www.ti.com ........................................................................................................................................................ SLVS653A–JUNE 2008–REVISED AUGUST 2009
Revision History
Changes from Original (June 2008) to Revision A ......................................................................................................... Page
•
•
•
•
•
Added Feature - Output Overvoltage Protection ................................................................................................................... 1
Changed Title From: High Efficient... To: Highly Efficient...................................................................................................... 1
Added Output overvoltage protection to the CONTROL STAGE ELECTRICAL CHARACTERISTICS................................ 3
Added Overvoltage Protection section ................................................................................................................................ 18
Changed Sentence in the PROGRAMMING THE OUTPUT VOLTAGE section - From: As an example, if an output
voltage of 3.3 V is needed, a 1-MΩ resistor should be chosen for R1. To: As an example, if an output voltage of 3.3
V is needed, a 1-MΩ resistor should be chosen for R1 if R2 is 180-kΩ.............................................................................. 19
•
Added Figure - PCB Layout Suggestion.............................................................................................................................. 21
Copyright © 2008–2009, Texas Instruments Incorporated
Submit Documentation Feedback
23
Product Folder Link(s): TPS63010 TPS63011 TPS63012
PACKAGE OPTION ADDENDUM
www.ti.com
18-Aug-2009
PACKAGING INFORMATION
Orderable Device
TPS63010YFFR
TPS63010YFFT
TPS63011YFFR
TPS63011YFFT
TPS63012YFFR
TPS63012YFFT
Status (1)
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
Drawing
DSBGA
YFF
20
20
20
20
20
20
3000 Green (RoHS &
no Sb/Br)
SNAGCU
SNAGCU
SNAGCU
SNAGCU
SNAGCU
SNAGCU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
YFF
YFF
YFF
YFF
YFF
250 Green (RoHS &
no Sb/Br)
3000 Green (RoHS &
no Sb/Br)
250 Green (RoHS &
no Sb/Br)
3000 Green (RoHS &
no Sb/Br)
250 Green (RoHS &
no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
18-Aug-2009
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TPS63010YFFR
TPS63010YFFT
TPS63011YFFR
TPS63011YFFT
TPS63012YFFR
TPS63012YFFT
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
YFF
YFF
YFF
YFF
YFF
YFF
20
20
20
20
20
20
3000
250
180.0
180.0
180.0
180.0
180.0
180.0
8.4
8.4
8.4
8.4
8.4
8.4
2.2
2.2
2.2
2.2
2.2
2.2
2.35
2.35
2.35
2.35
2.35
2.35
0.8
0.8
0.8
0.8
0.8
0.8
4.0
4.0
4.0
4.0
4.0
4.0
8.0
8.0
8.0
8.0
8.0
8.0
Q1
Q1
Q1
Q1
Q1
Q1
3000
250
3000
250
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
18-Aug-2009
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TPS63010YFFR
TPS63010YFFT
TPS63011YFFR
TPS63011YFFT
TPS63012YFFR
TPS63012YFFT
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
DSBGA
YFF
YFF
YFF
YFF
YFF
YFF
20
20
20
20
20
20
3000
250
190.5
190.5
190.5
190.5
190.5
190.5
212.7
212.7
212.7
212.7
212.7
212.7
31.8
31.8
31.8
31.8
31.8
31.8
3000
250
3000
250
Pack Materials-Page 2
X: Max = 1972 µm, Min = 1872 µm
Y: Max = 2176 µm, Min = 2076 µm
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
Amplifiers
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
www.ti.com/audio
Data Converters
DLP® Products
Automotive
www.ti.com/automotive
www.ti.com/communications
Communications and
Telecom
DSP
dsp.ti.com
Computers and
Peripherals
www.ti.com/computers
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
Consumer Electronics
Energy
www.ti.com/consumer-apps
www.ti.com/energy
Logic
Industrial
www.ti.com/industrial
Power Mgmt
Microcontrollers
RFID
power.ti.com
Medical
www.ti.com/medical
microcontroller.ti.com
www.ti-rfid.com
Security
www.ti.com/security
Space, Avionics &
Defense
www.ti.com/space-avionics-defense
RF/IF and ZigBee® Solutions www.ti.com/lprf
Video and Imaging
Wireless
www.ti.com/video
www.ti.com/wireless-apps
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2010, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明