TPS76718-EP [TI]
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS;型号: | TPS76718-EP |
厂家: | TEXAS INSTRUMENTS |
描述: | FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS |
文件: | 总28页 (文件大小:855K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TPS76715-EP, TPS76718-EP, TPS76725-EP, TPS76727-EP
TPS76728-EP, TPS76730-EP, TPS76733-EP, TPS76750-EP, TPS76701-EP
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS157 – MARCH 2003
D
Controlled Baseline
– One Assembly/Test Site, One Fabrication
Site
D
D
D
Fast Transient Response
2% Tolerance Over Specified Conditions for
Fixed-Output Versions
D
D
D
D
D
D
Extended Temperature Performance of
–40°C to 125°C
Open Drain Power-On Reset With 200-ms
Delay (See TPS768xx for PG Option)
Enhanced Diminishing Manufacturing
Sources (DMS) Support
D
20-Pin TSSOP PowerPAD (PWP) Package
Thermal Shutdown Protection
D
Enhanced Product Change Notification
†
PWP PACKAGE
(TOP VIEW)
Qualification Pedigree
1 A Low-Dropout Voltage Regulator
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
GND/HSINK
GND/HSINK
GND/HSINK
NC
Available in 1.5-V, 1.8-V, 2.5-V, 2.7-V, 2.8-V,
3.0-V, 3.3-V, 5.0-V Fixed Output and
Adjustable Versions
GND/HSINK
GND
NC
NC
D
D
Dropout Voltage Down to 230 mV at 1 A
(TPS76750)
EN
RESET
FB/NC
IN
IN
Ultralow 85 µA Typical Quiescent Current
OUT
†
Component qualification in accordance with JEDEC and industry
standards to ensure reliable operation over an extended
temperature range. This includes, but is not limited to, Highly
Accelerated Stress Test (HAST) or biased 85/85, temperature
cycle, autoclave or unbiased HAST, electromigration, bond
intermetallic life, and mold compound life. Such qualification
testing should not be viewed as justifying use of this component
beyond specified performance and environmental limits.
NC
OUT
GND/HSINK
GND/HSINK
GND/HSINK
GND/HSINK
NC – No internal connection
description
This device is designed to have a fast transient response and be stable with 10-µF low ESR capacitors. This
combination provides high performance at a reasonable cost.
Because the PMOS device behaves as a low-value resistor, the dropout voltage is very low (typically 230 mV
at an output current of 1 A for the TPS76750) and is directly proportional to the output current. Additionally, since
the PMOS pass element is a voltage-driven device, the quiescent current is very low and independent of output
loading (typically 85 µA over the full range of output current, 0 mA to 1 A). These two key specifications yield
a significant improvement in operating life for battery-powered systems. This LDO family also features a sleep
mode; applying a TTL high signal to EN (enable) shuts down the regulator, reducing the quiescent current to
1 µA at T = 25°C.
J
TheRESET output of the TPS767xx initiates a reset in microcomputer and microprocessor systems in the event
of an undervoltage condition. An internal comparator in the TPS767xx monitors the output voltage of the
regulator to detect an undervoltage condition on the regulated output voltage.
The TPS767xx is offered in 1.5-V, 1.8-V, 2.5-V, 2.7-V, 2.8-V, 3.0-V, 3.3-V, and 5.0-V fixed-voltage versions and
in an adjustable version (programmable over the range of 1.5 V to 5.5 V). Output voltage tolerance is specified
as a maximum of 2% over line, load, and temperature ranges. The TPS767xx family is available in a 20-pin PWP
package.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PowerPAD is a trademark of Texas Instruments.
Copyright 2003, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS76715-EP, TPS76718-EP, TPS76725-EP, TPS76727-EP
TPS76728-EP, TPS76730-EP, TPS76733-EP, TPS76750-EP, TPS76701-EP
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS157 – MARCH 2003
TPS76733
DROPOUT VOLTAGE
TPS76733
vs
FREE-AIR TEMPERATURE
LOAD TRANSIENT RESPONSE
3
10
2
10
1
10
0
10
100
C
T
= 10 µF
= 25°C
o
A
I
= 1 A
50
0
O
–50
–100
1
I
O
= 10 mA
0.5
0
–1
10
10
I
= 0
O
C
= 10 µF
o
–2
–60 –40 –20
0
20 40 60 80 100 120 140
0
100 200 300 400 500 600 700 800 900 1000
T
A
– Free-Air Temperature – °C
t – Time – µs
AVAILABLE OPTIONS
OUTPUT
VOLTAGE
(V)
TSSOP
(PWP)
T
J
†
TYP
5.0
3.3
3.0
2.8
2.7
2.5
1.8
1.5
TPS76750QPWPREP
TPS76733QPWPREP
‡
TPS76730QPWPREP
TPS76728QPWPREP
TPS76727QPWPREP
‡
‡
–40°C to 125°C
TPS76725QPWPREP
TPS76718QPWPREP
TPS76715QPWPREP
Adjustable
1.5 V to 5.5 V
TPS76701QPWPREP
†
‡
Available taped and reeled in quantities of 2000 per reel.
This devices is product preview.
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS76715-EP, TPS76718-EP, TPS76725-EP, TPS76727-EP
TPS76728-EP, TPS76730-EP, TPS76733-EP, TPS76750-EP, TPS76701-EP
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS157 – MARCH 2003
TPS767xx
6
7
16
V
I
IN
IN
RESET
RESET
14
13
OUT
OUT
V
O
5
0.1 µF
EN
†
C
o
+
10 µF
GND
3
†
See application information section for capacitor selection details.
Figure 1. Typical Application Configuration (For Fixed Output Options)
functional block diagram—adjustable version
IN
EN
RESET
OUT
_
+
+
_
200 ms Delay
R1
R2
V
ref
= 1.1834 V
FB/NC
GND
External to the device
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS76715-EP, TPS76718-EP, TPS76725-EP, TPS76727-EP
TPS76728-EP, TPS76730-EP, TPS76733-EP, TPS76750-EP, TPS76701-EP
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS157 – MARCH 2003
functional block diagram—fixed-voltage version
IN
EN
RESET
OUT
_
+
+
_
200 ms Delay
R1
R2
V
ref
= 1.1834 V
GND
Terminal Functions
PWP Package
TERMINAL
NAME
I/O
DESCRIPTION
NO.
5
EN
I
I
Enable input
FB/NC
15
3
Feedback input voltage for adjustable device (no connect for fixed options)
GND
Regulator ground
Ground/heatsink
GND/HSINK
1, 2, 9, 10, 11,
12, 19, 20
IN
6, 7
4, 8, 17, 18
13, 14
I
Input voltage
NC
No connect
OUT
RESET
O
O
Regulated output voltage
RESET output
16
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS76715-EP, TPS76718-EP, TPS76725-EP, TPS76727-EP
TPS76728-EP, TPS76730-EP, TPS76733-EP, TPS76750-EP, TPS76701-EP
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS157 – MARCH 2003
timing diagram
V
I
†
V
res
V
res
t
‡
‡
V
O
V
IT+
V
IT+
Threshold
Voltage
Less than 5% of the
output voltage
‡
‡
V
IT–
V
IT–
t
RESET
Output
200 ms
Delay
200 ms
Delay
Output
Undefined
Output
Undefined
t
†
‡
V
istheminimuminputvoltageforavalidRESET. ThesymbolV
isnotcurrentlylistedwithinEIAorJEDECstandardsforsemiconductor
–Trip voltage is typically 5% lower than the output voltage (95%V ) V to V is the hysteresis voltage.
O IT–
res
symbology.
res
V
IT
IT+
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS76715-EP, TPS76718-EP, TPS76725-EP, TPS76727-EP
TPS76728-EP, TPS76730-EP, TPS76733-EP, TPS76750-EP, TPS76701-EP
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS157 – MARCH 2003
Ĕ
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
‡
Input voltage range , V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to 13.5 V
I
Voltage range at EN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to V + 0.3 V
I
Maximum RESET voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16.5 V
Peak output current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Internally limited
Output voltage, V (OUT, FB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
O
Continuous total power dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See dissipation rating tables
Operating virtual junction temperature range, T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to 125°C
J
Storage temperature range, T
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
stg
ESD rating, HBM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 kV
†
‡
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
All voltage values are with respect to network terminal ground.
DISSIPATION RATING TABLE – FREE-AIR TEMPERATURES
AIR FLOW
(CFM)
T
< 25°C
DERATING FACTOR
T
= 70°C
T = 85°C
A
A
A
PACKAGE
POWER RATING
ABOVE T = 25°C
POWER RATING POWER RATING
A
0
2.9 W
23.5 mW/°C
34.6 mW/°C
23.8 mW/°C
57.9 mW/°C
1.9 W
2.8 W
1.9 W
4.6 W
1.5 W
2.2 W
1.5 W
3.8 W
§
PWP
PWP
300
0
4.3 W
3 W
¶
300
7.2 W
§
¶
This parameter is measured with the recommended copper heat sink pattern on a 1-layer PCB, 5-in × 5-in PCB, 1 oz. copper,
2-in × 2-in coverage (4 in ).
This parameter is measured with the recommended copper heat sink pattern on a 8-layer PCB, 1.5-in × 2-in PCB, 1 oz. copper
2
2
2
with layers 1, 2, 4, 5, 7, and 8 at 5% coverage (0.9 in ) and layers 3 and 6 at 100% coverage (6 in ). For more information, refer
to TI technical brief SLMA002.
recommended operating conditions
MIN
2.7
1.5
0
MAX
10
UNIT
V
Input voltage, V #
I
Output voltage range, V
5.5
V
O
Output current, I (see Note 1)
1.0
A
O
Operating virtual junction temperature, T (see Note 1)
–40
125
°C
J
#
To calculate the minimum input voltage for your maximum output current, use the following equation: V
I(min)
= V
+ V
.
DO(max load)
O(max)
NOTE 1: Continuous current and operating junction temperature are limited by internal protection circuitry, but it is not recommended that the
device operate under conditions beyond those specified in this table for extended periods of time.
6
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS76715-EP, TPS76718-EP, TPS76725-EP, TPS76727-EP
TPS76728-EP, TPS76730-EP, TPS76733-EP, TPS76750-EP, TPS76701-EP
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS157 – MARCH 2003
electrical characteristics over recommended operating free-air temperature range,
V = V
+ 1 V, I = 1 mA, EN = 0 V, C = 10 µF (unless otherwise noted)
I
O(typ)
O
o
PARAMETER
TEST CONDITIONS
1.5 V ≤ V ≤ 5.5 V, T = 25°C
MIN
TYP
MAX
UNIT
V
O
O
J
TPS76701
TPS76715
TPS76718
TPS76725
TPS76727
TPS76728
TPS76730
TPS76733
TPS76750
1.5 V ≤ V ≤ 5.5 V,
T = –40°C to 125°C
0.98V
1.02V
O
J
O
O
T = 25°C,
J
2.7 V < V < 10 V
IN
1.5
1.8
2.5
2.7
2.8
3.0
3.3
5.0
85
T = –40°C to 125°C, 2.7 V < V < 10 V
J IN
1.470
1.530
T = 25°C,
J
2.8 V < V < 10 V
IN
T = –40°C to 125°C, 2.8 V < V < 10 V
J IN
1.764
2.450
2.646
2.744
2.940
3.234
4.900
1.836
2.550
2.754
2.856
3.060
3.366
5.100
125
T = 25°C,
J
3.5 V < V < 10 V
IN
T = –40°C to 125°C, 3.5 V < V < 10 V
J IN
T = 25°C,
J
3.7 V < V < 10 V
IN
Output voltage (10 µA to 1 A load)
(see Note 2)
V
T = –40°C to 125°C, 3.7 V < V < 10 V
J IN
T = 25°C,
J
3.8 V < V < 10 V
IN
T = –40°C to 125°C, 3.8 V < V < 10 V
J IN
T = 25°C,
J
4.0 V < V < 10 V
IN
T = –40°C to 125°C, 4.0 V < V < 10 V
J IN
T = 25°C,
J
4.3 V < V < 10 V
IN
T = –40°C to 125°C, 4.3 V < V < 10 V
J IN
T = 25°C,
J
6.0 V < V < 10 V
IN
T = –40°C to 125°C, 6.0 V < V < 10 V
J IN
10 µA < I < 1 A,
T = 25°C
J
Quiescent current (GND current)
EN = 0V, (see Note 2)
O
µA
I
O
= 1 A,
T = –40°C to 125°C
J
Output voltage line regulation (∆V /V
(see Notes 2 and 3)
O
O
)
V
O
+ 1 V < V ≤ 10 V, T = 25°C
0.01
3
%/V
mV
I
J
Load regulation
BW = 200 Hz to 100 kHz, I = 1 A,
C
Output noise voltage (TPS76718)
Output current limit
55
µVrms
C
= 10 µF,
T = 25°C
J
o
V
O
= 0 V
1.7
2
A
Thermal shutdown junction temperature
150
°C
EN = V
EN = V
T = 25°C,
J
I,
I,
1
µA
µA
2.7 V < V < 10 V
I
Standby current
T = –40°C to 125°C
J
10
2.7 V < V < 10 V
I
FB input current
TPS76701
FB = 1.5 V
2
nA
V
High level enable input voltage
Low level enable input voltage
1.7
0.9
V
f = 1 KHz,
T = 25°C
J
C
= 10 µF,
o
Power supply ripple rejection (see Note 2)
60
dB
NOTES: 2. Minimum IN operating voltage is 2.7 V or V
+ 1 V, whichever is greater. Maximum IN voltage 10V.
O(typ)
= 2.7 V:
3. If V ≤ 1.8 V then V
Imax
= 10 V, V
Imin
O
OǒVImax * 2.7 VǓ
V
ǒ
Ǔ
Line Reg. (mV) + %ńV
1000
100
If V ≥ 2.5 V then V
Imax
= 10 V, V
= V + 1 V:
Imin O
O
* ǒV
100
Ǔ
) 1 V Ǔ
1000
ǒVImax
V
O
O
ǒ
Ǔ
Line Reg. (mV) + %ńV
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS76715-EP, TPS76718-EP, TPS76725-EP, TPS76727-EP
TPS76728-EP, TPS76730-EP, TPS76733-EP, TPS76750-EP, TPS76701-EP
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS157 – MARCH 2003
electrical characteristics over recommended operating free-air temperature range,
V = V
+ 1 V, I = 1 mA, EN = 0 V, C = 10 µF (unless otherwise noted) (continued)
I
O(typ)
O
o
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
Minimum input voltage for valid RESET
Trip threshold voltage
Hysteresis voltage
I
= 300 µA
1.1
V
O(RESET)
V
decreasing
92
98
%V
%V
V
O
O
Measured at V
0.5
O
O
Reset
Output low voltage
V = 2.7 V,
I
= 1 mA
0.15
0.4
1
I
O(RESET)
Leakage current
V
= 5 V
µA
(RESET)
RESET time-out delay
200
0
ms
EN = 0 V
EN = V
–1
–1
1
1
Input current (EN)
µA
I
I
O
I
O
I
O
I
O
I
O
I
O
I
O
I
O
= 1 A,
= 1 A,
= 1 A,
= 1 A,
= 1 A,
= 1 A,
= 1 A,
= 1 A,
T = 25°C
500
450
350
230
J
TPS76728
T = –40°C to 125°C
J
825
675
575
380
T = 25°C
J
TPS76730
TPS76733
TPS76750
T = –40°C to 125°C
J
Dropout voltage (see Note 4)
mV
T = 25°C
J
T = –40°C to 125°C
J
T = 25°C
J
T = –40°C to 125°C
J
NOTE 4: INvoltageequalsV (typ)–100mV;TPS76701outputvoltagesetto3.3Vnominalwithexternalresistordivider.TPS76715,TPS76718,
O
TPS76725, and TPS76727 dropout voltage limited by input voltage range limitations (i.e., TPS76730 input voltage needs to drop to 2.9
V for purpose of this test).
TYPICAL CHARACTERISTICS
Table of Graphs
FIGURE
vs Output current
vs Free-air temperature
vs Free-air temperature
vs Frequency
2, 3, 4
5, 6, 7
8, 9
V
Output voltage
O
Ground current
Power supply ripple rejection
Output spectral noise density
Input voltage (min)
10
vs Frequency
11
vs Output voltage
vs Frequency
12
Z
o
Output impedance
13
V
DO
Dropout voltage
vs Free-air temperature
14
Line transient response
Load transient response
Output voltage
15, 17
16, 18
19
V
O
vs Time
Dropout voltage
vs Input voltage
vs Output current
20
Equivalent series resistance (ESR)
22 – 25
8
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS76715-EP, TPS76718-EP, TPS76725-EP, TPS76727-EP
TPS76728-EP, TPS76730-EP, TPS76733-EP, TPS76750-EP, TPS76701-EP
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS157 – MARCH 2003
TYPICAL CHARACTERISTICS
TPS76715
TPS76733
OUTPUT VOLTAGE
OUTPUT VOLTAGE
vs
vs
OUTPUT CURRENT
OUTPUT CURRENT
1.4985
3.2835
3.2830
V = 2.7 V
I
V = 4.3 V
I
T
A
= 25°C
T
A
= 25°C
1.4980
1.4975
1.4970
1.4965
1.4960
3.2825
3.2820
3.2815
3.2810
3.2805
3.2800
1.4955
1.4950
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
1
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
– Output Current – A
1
I
O
I
O
– Output Current – A
Figure 2
Figure 3
TPS76725
TPS76733
OUTPUT VOLTAGE
vs
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
FREE-AIR TEMPERATURE
2.4960
2.4955
2.4950
2.4945
3.32
3.31
V = 3.5 V
I
V = 4.3 V
I
T
A
= 25°C
3.30
3.29
3.28
3.27
3.26
3.25
I
O
= 1 A
2.4940
2.4935
2.4930
I
O
= 1 mA
2.4925
2.4920
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
1
–60 –40 –20
0
20 40 60 80 100 120 140
I
O
– Output Current – A
T
A
– Free-Air Temperature – °C
Figure 4
Figure 5
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS76715-EP, TPS76718-EP, TPS76725-EP, TPS76727-EP
TPS76728-EP, TPS76730-EP, TPS76733-EP, TPS76750-EP, TPS76701-EP
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS157 – MARCH 2003
TYPICAL CHARACTERISTICS
TPS76715
OUTPUT VOLTAGE
vs
TPS76725
OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
FREE-AIR TEMPERATURE
1.515
2.515
2.510
2.505
2.500
2.495
2.490
V = 3.5 V
I
V = 2.7 V
I
1.510
1.505
1.500
1.495
1.490
1.485
I
O
= 1 A
I
O
= 1 A
I
= 1 mA
O
I
O
= 1 mA
2.485
2.480
–60 –40 –20
0
20 40 60 80 100 120 140
–60 –40 –20
0
20
40
60
80 100 120
T
A
– Free-Air Temperature – °C
T
A
– Free-Air Temperature – °C
Figure 6
Figure 7
TPS76733
GROUND CURRENT
vs
FREE-AIR TEMPERATURE
92
90
V = 4.3 V
I
88
86
84
82
80
78
76
I
O
= 1 mA
I
O
= 1 A
I
O
= 500 mA
74
72
–60 –40 –20
0
20 40 60 80 100 120 140
T
A
– Free-Air Temperature – °C
Figure 8
10
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS76715-EP, TPS76718-EP, TPS76725-EP, TPS76727-EP
TPS76728-EP, TPS76730-EP, TPS76733-EP, TPS76750-EP, TPS76701-EP
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS157 – MARCH 2003
TYPICAL CHARACTERISTICS
TPS76715
GROUND CURRENT
vs
TPS76733
POWER SUPPLY RIPPLE REJECTION
vs
FREE-AIR TEMPERATURE
FREQUENCY
90
80
70
100
95
90
85
80
75
V = 4.3 V
I
V = 2.7 V
I
C
= 10 µF
= 1 A
= 25°C
o
I
T
O
A
60
50
40
30
20
I
= 1 A
O
I
O
= 1 mA
I
= 500 mA
O
10
0
–10
10
100
1k
–60 –40 –20
0
20 40 60 80 100 120 140
10k
100k
1M
T
A
– Free-Air Temperature – °C
f – Frequency – Hz
Figure 9
Figure 10
TPS76733
OUTPUT SPECTRAL NOISE DENSITY
vs
FREQUENCY
–5
10
10
V = 4.3 V
I
o
A
C
T
= 10 µF
= 25°C
I
O
= 7 mA
–6
I
O
= 1 A
–7
–8
10
10
2
10
3
10
4
10
5
10
f – Frequency – Hz
Figure 11
11
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS76715-EP, TPS76718-EP, TPS76725-EP, TPS76727-EP
TPS76728-EP, TPS76730-EP, TPS76733-EP, TPS76750-EP, TPS76701-EP
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS157 – MARCH 2003
TYPICAL CHARACTERISTICS
INPUT VOLTAGE (MIN)
vs
OUTPUT VOLTAGE
4
I
O
= 1 A
T
A
= 25°C
T
A
= 125°C
3
T
A
= –40°C
2.7
2
1.5 1.75
2
2.25 2.5 2.75
3
3.25 3.5
V
O
– Output Voltage – V
Figure 12
TPS76733
TPS76733
DROPOUT VOLTAGE
vs
OUTPUT IMPEDANCE
vs
FREQUENCY
FREE-AIR TEMPERATURE
3
2
1
0
0
–1
–2
10
10
10
10
V = 4.3 V
I
C
T
A
= 10 µF
= 25°C
o
I
= 1 A
O
I
O
= 1 mA
10
I
O
= 10 mA
I
= 1 A
–1
O
10
10
I
= 0
O
C
= 10 µF
o
–2
10
1
2
10
3
10
4
5
10
6
10
–60 –40 –20
0
20 40 60 80 100 120 140
10
10
f – Frequency – kHz
T
A
– Free-Air Temperature – °C
Figure 13
Figure 14
12
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS76715-EP, TPS76718-EP, TPS76725-EP, TPS76727-EP
TPS76728-EP, TPS76730-EP, TPS76733-EP, TPS76750-EP, TPS76701-EP
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS157 – MARCH 2003
TYPICAL CHARACTERISTICS
TPS76715
TPS76715
LINE TRANSIENT RESPONSE
LOAD TRANSIENT RESPONSE
100
C
T
= 10 µF
= 25°C
o
A
3.7
2.7
50
0
–50
–100
10
1
0
0.5
0
–10
C
T
A
= 10 µF
= 25°C
o
0
20 40 60 80 100 120 140 160 180 200
0
100 200 300 400 500 600 700 800 900 1000
t – Time – µs
t – Time – µs
Figure 15
Figure 16
TPS76733
TPS76733
LINE TRANSIENT RESPONSE
LOAD TRANSIENT RESPONSE
100
C
T
= 10 µF
= 25°C
C
T
= 10 µF
= 25°C
o
A
o
A
50
0
5.3
–50
–100
1
4.3
10
0
0.5
0
–10
0
20 40 60 80 100 120 140 160 180 200
0
100 200 300 400 500 600 700 800 900 1000
t – Time – µs
t – Time – µs
Figure 17
Figure 18
13
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS76715-EP, TPS76718-EP, TPS76725-EP, TPS76727-EP
TPS76728-EP, TPS76730-EP, TPS76733-EP, TPS76750-EP, TPS76701-EP
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS157 – MARCH 2003
TYPICAL CHARACTERISTICS
TPS76733
TPS76701
OUTPUT VOLTAGE
DROPOUT VOLTAGE
vs
vs
TIME (AT STARTUP)
INPUT VOLTAGE
4
900
800
700
600
500
400
300
200
C
I
T
A
= 10 µF
= 1 A
= 25°C
I
O
= 1 A
o
O
3
2
1
T
A
= 125°C
0
T
A
= 25°C
T
A
= –40°C
0
100
0
2.5
3
3.5
4
4.5
5
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
1
t – Time – ms
V – Input Voltage – V
I
Figure 19
Figure 20
To Load
IN
V
I
OUT
+
C
o
R
EN
L
GND
ESR
Figure 21. Test Circuit for Typical Regions of Stability (Figures 22 through 25) (Fixed Output Options)
14
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS76715-EP, TPS76718-EP, TPS76725-EP, TPS76727-EP
TPS76728-EP, TPS76730-EP, TPS76733-EP, TPS76750-EP, TPS76701-EP
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS157 – MARCH 2003
TYPICAL CHARACTERISTICS
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE
vs
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE
vs
†
†
OUTPUT CURRENT
OUTPUT CURRENT
10
10
Region of Instability
Region of Instability
V
= 3.3 V
O
C
= 4.7 µF
o
V = 4.3 V
I
J
T
= 125°C
1
1
Region of Stability
Region of Stability
V
C
= 3.3 V
= 4.7 µF
O
o
V = 4.3 V
I
A
T
= 25°C
0.1
0.1
0
200
400
600
800
1000
0
200
400
600
800
1000
I
O
– Output Current – mA
I
O
– Output Current – mA
Figure 22
Figure 23
TYPICAL REGION OF STABILITY
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE
vs
†
†
EQUIVALENT SERIES RESISTANCE
vs
OUTPUT CURRENT
OUTPUT CURRENT
10
10
Region of Instability
Region of Instability
V
= 3.3 V
O
C
= 22 µF
o
V = 4.3 V
I
J
T
= 125°C
1
1
Region of Stability
Region of Stability
V
C
= 3.3 V
= 22 µF
O
o
V = 4.3 V
I
A
T
= 25°C
0.1
0.1
0
200
400
600
800
1000
0
200
400
600
800
1000
I
O
– Output Current – mA
I
O
– Output Current – mA
Figure 24
Figure 25
†
Equivalent series resistance (ESR) refers to the total series resistance, including the ESR of the capacitor, any series resistance added
externally, and PWB trace resistance to C .
o
15
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS76715-EP, TPS76718-EP, TPS76725-EP, TPS76727-EP
TPS76728-EP, TPS76730-EP, TPS76733-EP, TPS76750-EP, TPS76701-EP
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS157 – MARCH 2003
APPLICATION INFORMATION
The TPS767xx family includes eight fixed-output voltage regulators (1.5 V, 1.8 V, 2.5 V, 2.7 V, 2.8 V, 3.0 V,
3.3 V, and 5.0 V), and an adjustable regulator, the TPS76701 (adjustable from 1.5 V to 5.5 V).
device operation
The TPS767xx features very low quiescent current, which remains virtually constant even with varying loads.
Conventional LDO regulators use a pnp pass element, the base current of which is directly proportional to the
load current through the regulator (I = I /β). The TPS767xx uses a PMOS transistor to pass current; because
B
C
the gate of the PMOS is voltage driven, operating current is low and invariable over the full load range.
Another pitfall associated with the pnp-pass element is its tendency to saturate when the device goes into
dropout. The resulting drop in β forces an increase in I to maintain the load. During power up, this translates
B
to large start-up currents. Systems with limited supply current may fail to start up. In battery-powered systems,
it means rapid battery discharge when the voltage decays below the minimum required for regulation. The
TPS767xx quiescent current remains low even when the regulator drops out, eliminating both problems.
The TPS767xx family also features a shutdown mode that places the output in the high-impedance state
(essentially equal to the feedback-divider resistance) and reduces quiescent current to 2 µA. If the shutdown
feature is not used, EN should be tied to ground.
minimum load requirements
The TPS767xx family is stable even at zero load; no minimum load is required for operation.
FB—pin connection (adjustable version only)
The FB pin is an input pin to sense the output voltage and close the loop for the adjustable option . The output
voltage is sensed through a resistor divider network to close the loop as shown in Figure 27. Normally, this
connection should be as short as possible; however, the connection can be made near a critical circuit to
improve performance at that point. Internally, FB connects to a high-impedance wide-bandwidth amplifier and
noise pickup feeds through to the regulator output. Routing the FB connection to minimize/avoid noise pickup
is essential.
external capacitor requirements
An input capacitor is not usually required; however, a ceramic bypass capacitor (0.047 µF or larger) improves
load transient response and noise rejection if the TPS767xx is located more than a few inches from the power
supply. A higher-capacitance electrolytic capacitor may be necessary if large (hundreds of milliamps) load
transients with fast rise times are anticipated.
Like all low dropout regulators, the TPS767xx requires an output capacitor connected between OUT and GND
to stabilize the internal control loop. The minimum recommended capacitance value is 10 µF and the ESR
(equivalent series resistance) must be between 50 mΩ and 1.5 Ω. Capacitor values 10 µF or larger are
acceptable, provided the ESR is less than 1.5 Ω. Solid tantalum electrolytic, aluminum electrolytic, and
multilayer ceramic capacitors are all suitable, provided they meet the requirements described above. Most of
the commercially available 10 µF surface-mount ceramic capacitors, including devices from Sprague and
Kemet, meet the ESR requirements stated above.
16
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS76715-EP, TPS76718-EP, TPS76725-EP, TPS76727-EP
TPS76728-EP, TPS76730-EP, TPS76733-EP, TPS76750-EP, TPS76701-EP
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS157 – MARCH 2003
APPLICATION INFORMATION
external capacitor requirements (continued)
TPS767xx
6
7
16
RESET
V
I
IN
RESET
IN
250 kΩ
14
13
V
OUT
OUT
O
C1
0.1 µF
5
EN
C
+
o
10 µF
GND
3
Figure 26. Typical Application Circuit (Fixed Versions)
programming the TPS76701 adjustable LDO regulator
The output voltage of the TPS76701 adjustable regulator is programmed using an external resistor divider as
shown in Figure 27. The output voltage is calculated using:
R1
R2
ǒ1 )
Ǔ
(1)
V
+ V
O
ref
Where:
V
= 1.1834 V typ (the internal reference voltage)
ref
Resistors R1 and R2 should be chosen for approximately 50-µA divider current. Lower value resistors can be
used but offer no inherent advantage and waste more power. Higher values should be avoided as leakage
currents at FB increase the output voltage error. The recommended design procedure is to choose
R2 = 30.1 kΩ to set the divider current at 50 µA and then calculate R1 using:
V
O
R1 +
ǒ
* 1
Ǔ
R2
(2)
V
ref
OUTPUT VOLTAGE
PROGRAMMING GUIDE
TPS76701
OUTPUT
VOLTAGE
R1
33.2
R2
UNIT
Reset Output
250 kΩ
V
I
IN
RESET
OUT
0.1 µF
2.5 V
3.3 V
30.1
30.1
30.1
30.1
kΩ
kΩ
kΩ
kΩ
≥ 1.7 V
53.6
61.9
90.8
EN
V
O
3.6 V
≤ 0.9 V
R1
C
4.75 V
o
FB / NC
GND
R2
Figure 27. TPS76701 Adjustable LDO Regulator Programming
17
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS76715-EP, TPS76718-EP, TPS76725-EP, TPS76727-EP
TPS76728-EP, TPS76730-EP, TPS76733-EP, TPS76750-EP, TPS76701-EP
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS157 – MARCH 2003
APPLICATION INFORMATION
reset indicator
The TPS767xx features a RESET output that can be used to monitor the status of the regulator. The internal
comparator monitors the output voltage: when the output drops to between 92% and 98% of its nominal
regulated value, the RESET output transistor turns on, taking the signal low. The open-drain output requires
a pullup resistor. If not used, it can be left floating. RESET can be used to drive power-on reset circuitry or as
a low-battery indicator. RESET does not assert itself when the regulated output voltage falls outside the
specified 2% tolerance, but instead reports an output voltage low relative to its nominal regulated value (refer
to timing diagram for start-up sequence).
regulator protection
The TPS767xx PMOS-pass transistor has a built-in back diode that conducts reverse currents when the input
voltage drops below the output voltage (e.g., during power down). Current is conducted from the output to the
input and is not internally limited. When extended reverse voltage is anticipated, external limiting may be
appropriate.
The TPS767xx also features internal current limiting and thermal protection. During normal operation, the
TPS767xxlimitsoutputcurrenttoapproximately1.7A. Whencurrentlimitingengages, theoutputvoltagescales
back linearly until the overcurrent condition ends. While current limiting is designed to prevent gross device
failure, care should be taken not to exceed the power dissipation ratings of the package. If the temperature of
the device exceeds 150°C(typ), thermal-protection circuitry shuts it down. Once the device has cooled below
130°C(typ), regulator operation resumes.
power dissipation and junction temperature
Specified regulator operation is assured to a junction temperature of 125°C; the maximum junction temperature
should be restricted to 125°C under normal operating conditions. This restriction limits the power dissipation
the regulator can handle in any given application. To ensure the junction temperature is within acceptable limits,
calculate the maximum allowable dissipation, P
, and the actual dissipation, P , which must be less than
D(max)
D
or equal to P
.
D(max)
The maximum-power-dissipation limit is determined using the following equation:
T max * T
J
A
P
+
D(max)
R
θJA
Where:
T max is the maximum allowable junction temperature.
J
R
is the thermal resistance junction-to-ambient for the package, i.e., 172°C/W for the 8-terminal
θJA
SOIC and 32.6°C/W for the 20-terminal PWP with no airflow.
T is the ambient temperature.
A
The regulator dissipation is calculated using:
+ ǒVI * V
Ǔ
P
I
D
O
O
Power dissipation resulting from quiescent current is negligible. Excessive power dissipation will trigger the
thermal protection circuit.
18
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TPS76715-EP, TPS76718-EP, TPS76725-EP, TPS76727-EP
TPS76728-EP, TPS76730-EP, TPS76733-EP, TPS76750-EP, TPS76701-EP
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORS
SGLS157 – MARCH 2003
MECHANICAL DATA
PWP (R-PDSO-G**)
PowerPAD PLASTIC SMALL-OUTLINE
20 PINS SHOWN
0,30
0,19
0,65
20
M
0,10
11
Thermal Pad
(See Note D)
0,15 NOM
4,50
4,30
6,60
6,20
Gage Plane
1
10
0,25
A
0°–ā8°
0,75
0,50
Seating Plane
0,10
0,15
0,05
1,20 MAX
PINS **
14
16
20
24
28
DIM
5,10
4,90
5,10
4,90
6,60
6,40
7,90
7,70
9,80
9,60
A MAX
A MIN
4073225/F 10/98
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusions.
D. The package thermal performance may be enhanced by bonding the thermal pad to an external thermal plane.
This pad is electrically and thermally connected to the backside of the die and possibly selected leads.
E. Falls within JEDEC MO-153
PowerPAD is a trademark of Texas Instruments Incorporated.
19
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
18-Sep-2008
PACKAGING INFORMATION
Orderable Device
TPS76701QPWPREP
TPS76715QPWPREP
TPS76718QPWPREP
TPS76725QPWPREP
TPS76733QPWPREP
TPS76750QPWPREP
V62/03630-01XE
Status (1)
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
Drawing
HTSSOP
PWP
20
20
20
20
20
20
20
20
20
20
20
20
2000 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
HTSSOP
HTSSOP
HTSSOP
HTSSOP
HTSSOP
HTSSOP
HTSSOP
HTSSOP
HTSSOP
HTSSOP
HTSSOP
PWP
PWP
PWP
PWP
PWP
PWP
PWP
PWP
PWP
PWP
PWP
2000 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
V62/03630-02XE
2000 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
V62/03630-03XE
2000 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
V62/03630-04XE
2000 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
V62/03630-08XE
2000 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
V62/03630-09XE
2000 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
18-Sep-2008
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TPS76701-EP, TPS76715-EP, TPS76718-EP, TPS76725-EP, TPS76733-EP, TPS76750-EP :
Catalog: TPS76701, TPS76715, TPS76718, TPS76725, TPS76733, TPS76750
Automotive: TPS76701-Q1, TPS76715-Q1, TPS76718-Q1, TPS76725-Q1, TPS76733-Q1, TPS76750-Q1
•
•
NOTE: Qualified Version Definitions:
Catalog - TI's standard catalog product
Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
•
•
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TPS76701QPWPREP HTSSOP PWP
TPS76715QPWPREP HTSSOP PWP
TPS76718QPWPREP HTSSOP PWP
TPS76725QPWPREP HTSSOP PWP
TPS76733QPWPREP HTSSOP PWP
TPS76750QPWPREP HTSSOP PWP
20
20
20
20
20
20
2000
2000
2000
2000
2000
2000
330.0
330.0
330.0
330.0
330.0
330.0
16.4
16.4
16.4
16.4
16.4
16.4
6.95
6.95
6.95
6.95
6.95
6.95
7.1
7.1
7.1
7.1
7.1
7.1
1.6
1.6
1.6
1.6
1.6
1.6
8.0
8.0
8.0
8.0
8.0
8.0
16.0
16.0
16.0
16.0
16.0
16.0
Q1
Q1
Q1
Q1
Q1
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TPS76701QPWPREP
TPS76715QPWPREP
TPS76718QPWPREP
TPS76725QPWPREP
TPS76733QPWPREP
TPS76750QPWPREP
HTSSOP
HTSSOP
HTSSOP
HTSSOP
HTSSOP
HTSSOP
PWP
PWP
PWP
PWP
PWP
PWP
20
20
20
20
20
20
2000
2000
2000
2000
2000
2000
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
38.0
38.0
38.0
38.0
38.0
38.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Audio
Applications
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
www.ti.com/security
Medical
Logic
Security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense www.ti.com/space-avionics-defense
microcontroller.ti.com
www.ti-rfid.com
Video and Imaging
www.ti.com/video
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
相关型号:
TPS76718-Q1
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORSWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS76718Q
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORSWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS76718QD
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORSWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS76718QDG4
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT LINEAR REGULATORSWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS76718QDR
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT LINEAR REGULATORSWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS76718QDRG4
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT LINEAR REGULATORSWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS76718QPWP
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORSWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS76718QPWPG4
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT LINEAR REGULATORSWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS76718QPWPR
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT LINEAR REGULATORSWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS76718QPWPREP
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT VOLTAGE REGULATORSWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS76718QPWPRG4
FAST-TRANSIENT-RESPONSE 1-A LOW-DROPOUT LINEAR REGULATORSWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS76718QPWPRQ1
Fast-Transient-Response 1-A Low-Dropout Voltage Regulators for Automotive 20-HTSSOP -40 to 125Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
©2020 ICPDF网 联系我们和版权申明