TRF7961RHBRG4 [TI]
TRF7961 全集成 13.56MHz RFID 读/写器 IC(符合 ISO15693 标准) | RHB | 32 | -40 to 110;型号: | TRF7961RHBRG4 |
厂家: | TEXAS INSTRUMENTS |
描述: | TRF7961 全集成 13.56MHz RFID 读/写器 IC(符合 ISO15693 标准) | RHB | 32 | -40 to 110 消费电路 商用集成电路 |
文件: | 总7页 (文件大小:355K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TRF7960/61
www.ti.com
SLOS504–AUGUST 2006
Multi-Standard Fully Integrated 13.56-MHz Radio Frequency Identification (RFID) Analog
Front End and Data Framing Reader System
FEATURES
•
Ultra-low power modes
– Power down < 1 µA
– Standby 120 µA
•
Completely integrated protocol handling
(OSI Model Layer 3 and below)
•
Separate internal high-PSRR power supplies
for analog, digital, and PA sections provides
noise isolation for superior read range and
reliability
– Active (Rx only) 10 mA
•
Parallel 8-Bit or Serial 4-pin SPI interface with
MCU using 12-byte FIFO
•
•
Ultra-small 32-pin QFN Package (5x5mm)
Available tools
•
Dual receiver input with AM and PM
demodulation to minimize communication
holes (patent pending).
– Reference design/EVM with development
software
•
•
•
Receiver AM and PM RSSI
– Source code available for MSP430
Reader-to-reader anti-collision
High Integration reduces total BOM and
board area
APPLICATIONS
•
•
Secure access control
– Single external 13.56 MHz crystal oscillator
Product authentication
– Printer ink cartridges
– Blood glucose monitors
Contactless payment systems
– MCU-selectable clock-frequency output of
RF, RF/2, or RF/4
– Adjustable 20 mA, high-PSRR LDO for
powering external MCU
•
•
Easy to use with high flexibility
DESCRIPTION
– Auto-configured default modes for each
supported ISO protocol
The TRF7960/61 is an integrated analog front end &
data framing system for a 13.56 MHz RFID reader
system. Built-in programming options make it
suitable for a wide range of applications both in
proximity and vicinity RFID systems.
– 11 user-programmable registers
– Selectable receiver gain and AGC
– Programmable output power
(100 mW or 200 mW)
The reader is configured by selecting the desired
protocol in the control registers. Direct access to all
control registers allows fine tuning of various reader
parameters as needed.
– Adjustable ASK Modulation Range
(8% to 30%)
– Built in receiver bandpass filter with user
selectable corner frequencies
•
Wide operating voltage range of 2.7 to 5.5 V
PRODUCT SELECTION TABLE
PROTOCOLS
DEVICE
ISO14443A/B
ISO15693
Tag-it™
HF-EPC
106 kbps
212 kbps
424 kbps
848 kbps
TRF7960
TRF7961
X
X
X
X
X
X
X
X
X
X
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Tag-it is a trademark of Texas Instruments Incorporated.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2006, Texas Instruments Incorporated
TRF7960/61
www.ti.com
SLOS504–AUGUST 2006
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
DESCRIPTION (CONTINUED)
VIN
VDD_X
TRF796x
SYS_CLK
Z-Matching
Circuit
TX_OUT
DATA_CLK
8
MSP430
RX_IN1
RX_IN2
VDD_I/O
Xtal
Figure 1. Typical Application
A parallel or serial interface can be used for
communication between the MCU & reader. When
hardware encoders and decoders are used
(accelerators for different standards), transmission
and receive functions use a 12-byte FIFO register.
For direct transmit or receive functions, the
encoders/decoders can be bypassed in order for the
MCU to process the data in real time. The transmitter
has selectable output-power levels of 100 mW
(+20 dBm) or 200 mW (+23 dBm) into a 50 Ω load
(at 5 V supply) and is capable of ASK or OOK
modulation. Integrated voltage regulators ensure
power-supply noise rejection for the complete reader
system.
The receiver system also includes a framing system.
This system performs the CRC and/or parity check,
removes the EOF and SOF settings, and organizes
the data in bytes. Framed data is then accessible to
the MCU via a 12-byte FIFO register and MCU
interface. The framing supports ISO14443 and
ISO15693 protocols.
The TRF7960/61 supports data communication
levels between 1.8-5.5 V for MCU I/O interface while
also providing a data synchronization clock. An
auxiliary 20 mA regulator (pin 32) is available for
additional system circuits.
Data transmission comprises low level encoding for
ISO15693, modified Miller for ISO14443-A,
high-bit-rate systems, Tag-it, and HF-EPC system
coding. Included with the data encoding is automatic
generation of SOF, EOF, CRC, and/or parity bits.
I/O_7
1
2
3
4
5
6
7
8
VDD_A
VIN
24
I/O_6 23
The receiver system enables AM and PM
demodulation using a dual-input architecture. The
receiver also includes an automatic gain control
option and selectable gain. Also included is a
selectable bandwidth to cover a broad range of input
sub-carrier signal options. The received signal
strength for AM and PM modulation is accessible via
the RSSI register. The receiver output is selectable
between a digitized sub-carrier signal and any of
eleven integrated sub-carrier decoders (two for
ISO15693 low bit rate, two for ISO15693 high bit
rate, two for ISO14443, three for ISO14443 high bit
rates, one for Tag-it, and one for HF-EPC system).
Selected decoders also deliver bit stream and a data
clock as outputs.
VDD_RF
VDD_PA
TX_OUT
VSS_PA
VSS_RX
RX_IN1
I/O_5
22
I/O_4 21
I/O_3 20
TRF796x
RHB-32
I/O_2
I/O_1
19
18
Thermal Pad
I/O_0 17
Figure 2. TRF796x Pin Assignments (Top View)
2
Submit Documentation Feedback
TRF7960/61
www.ti.com
SLOS504–AUGUST 2006
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range (unless otherwise noted)(1)
VALUE
UNIT
V
VIN
IO
Supply voltage
6
Output current
150
mA
Continuous power dissipation
See Dissipation Rating Table
Maximum junction temperature, any condition(2)
Maximum junction temperature, continuous operation, long term reliability(2)
Storage temperature range
140
125
°C
°C
°C
°C
kV
TJ
Tstg
–55 to 150
300
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds
HBM (Human Body Model)
2
ESDS rating:
CDM (Charge Device Model)
MM (Machine Model)
500
V
200
(1) The absolute maximum ratings under any condition is limited by the constraints of the silicon process. Stresses above these ratings may
cause permanent damage. Exposure to absolute maximum conditions for extended periods may degrade device reliability. These are
stress ratings only and functional operation of the device at these or any other conditions beyond those specified are not implied
(2) The maximum junction temperature for continuous operation is limited by package constraints. Operation above this temperature may
result in reduced reliability and/or lifetime of the device.
TABLE 5. PACKAGING/ORDERING INFORMATION(1)
PACKAGED DEVICES
TRF7960RHBT
PACKAGE TYPE
TRANSPORT MEDIA
Tape and Reel
Tape and Reel
Tape and Reel
Tape and Reel
QUANTITY
250
RHB – 32
TRF7960RHBR
TRF7961RHBT
3000
250
RHB – 32
TRF7961RHBR
3000
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
Web site at www.ti.com.
DISSIPATION RATINGS TABLE PER PACKAGE
POWER RATING(2)
(1)
θJC
θJA
PACKAGE
(°C/W)
(°C/W)
TA≤ 25°C
TA = 85°C
RHB (32)
31
36.4
2.7 W
1.1 W
(1) This data was taken using the JEDEC standard High-K test PCB.
(2) Power rating is determined with a junction temperature of 125°C. This is the point where distortion starts to substantially increase.
Thermal management of the final PCB should strive to keep the junction temperature at or below 125°C for best performance and long
term reliability.
RECOMMENDED OPERATING CONDITIONS
over operating free-air temperature range (unless otherwise noted)
MIN
2.7
TYP
MAX
5.5
UNIT
V
VIN
TJ
Supply voltage
5.0
Operating virtual junction temperature range
Operating ambient temperature range
Load impedance at TX OUT (pin 5)
–40
–40
125
110
°C
°C
Ω
TA
25
10
3
Submit Documentation Feedback
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Audio
Amplifiers
amplifier.ti.com
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
Digital Control
Military
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/military
Interface
Logic
interface.ti.com
logic.ti.com
Power Mgmt
Microcontrollers
power.ti.com
Optical Networking
Security
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
microcontroller.ti.com
Low Power Wireless www.ti.com/lpw
Telephony
Video & Imaging
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright 2006, Texas Instruments Incorporated
相关型号:
TRF7961RHBT
Multi-Standard Fully Integrated 13.56-MHz Radio Frequency Identification (RFID) Analog Front End and Data Framing Reader SystemWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TRF7961RHBTG4
TRF7961 全集成 13.56MHz RFID 读/写器 IC(符合 ISO15693 标准) | RHB | 32 | -40 to 110Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TRF7962A
FULLY INTEGRATED 13.56-MHz RFID READER/WRITER IC FOR ISO15693/ISO18000-3 STANDARDSWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TRF7962ARHBR
FULLY INTEGRATED 13.56-MHz RFID READER/WRITER IC FOR ISO15693/ISO18000-3 STANDARDSWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TRF7962ARHBT
FULLY INTEGRATED 13.56-MHz RFID READER/WRITER IC FOR ISO15693/ISO18000-3 STANDARDSWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TRF7963A
FULLY INTEGRATED 13.56-MHz RFID READER/WRITER IC FOR ISO14443A,B/NFC STANDARDSWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TRF7963ARHBR
FULLY INTEGRATED 13.56-MHz RFID EADER/WRITER FOR ISO14443A,B/NFC STANDARDSWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TRF7963ARHBT
FULLY INTEGRATED 13.56-MHz RFID EADER/WRITER FOR ISO14443A,B/NFC STANDARDSWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TRF7964A
MULTI-PROTOCOL FULLY INTEGRATED 13.56-MHz RFID READER/WRITER ICWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TRF7964ARHB
IC SPECIALTY CONSUMER CIRCUIT, Consumer IC:OtherWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TRF7964ARHBR
TRF7964A 多协议完全集成的 13.56MHz NFC/RFID 读/写器 IC | RHB | 32 | -40 to 110Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TRF7964ARHBT
TRF7964A 多协议完全集成的 13.56MHz NFC/RFID 读/写器 IC | RHB | 32 | -40 to 110Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
©2020 ICPDF网 联系我们和版权申明