TRSF3221IPW [TI]
LINE TRANSCEIVER, PDSO16, GREEN, PLASTIC, TSSOP-16;型号: | TRSF3221IPW |
厂家: | TEXAS INSTRUMENTS |
描述: | LINE TRANSCEIVER, PDSO16, GREEN, PLASTIC, TSSOP-16 驱动 光电二极管 接口集成电路 驱动器 |
文件: | 总16页 (文件大小:355K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TRSF3221
3-V TO 5.5-V SINGLE-CHANNEL RS-232 COMPATIBLE LINE DRIVER/RECEIVER
www.ti.com
SLLS857–AUGUST 2007
1
FEATURES
DB OR PW PACKAGE
•
Operates With 3-V to 5.5-V VCC Supply
(TOP VIEW)
•
•
•
•
•
Operates up to 1 Mbit/s
EN
C1+
V+
FORCEOFF
VCC
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
Low Standby Current . . . 1 μA Typ
External Capacitors . . . 4 × 0.1 μF
Accepts 5-V Logic Input With 3.3-V Supply
GND
C1−
C2+
C2−
V−
DOUT
RS-232 Bus-Pin ESD Protection Exceeds
±15 kV Using Human-Body Model (HBM)
FORCEON
DIN
•
Auto-Powerdown Feature Automatically
Disables Drivers for Power Savings
INVALID
ROUT
RIN
APPLICATIONS
•
Battery-Powered, Hand-Held, and Portable
Equipment
•
•
•
•
PDAs and Palmtop PCs
Notebooks, Sub-Notebooks, and Laptops
Digital Cameras
Mobile Phones and Wireless Devices
DESCRIPTION/ORDERING INFORMATION
The TRSF3221 consists of one line driver, one line receiver, and a dual charge-pump circuit with ±15-kV IEC
ESD protection pin-to-pin (serial-port connection pins, including GND). The TRSF3221 provides the electrical
interface between an asynchronous communication controller and the serial-port connector. The charge pump
and four small external capacitors allow operation from a single 3-V to 5.5-V supply. The TRSF3221 operates at
data signaling rates up to 1 Mbit/s and a driver output slew rate of 24 V/μs to 150 V/μs.
Flexible control options for power management are available when the serial port is inactive. The
auto-powerdown feature functions when FORCEON is low and FORCEOFF is high. During this mode of
operation, if the TRSF3221 does not sense a valid RS-232 signal on the receiver input, the driver output is
disabled. If FORCEOFF is set low and the enable (EN) input is high, both the driver and receiver are shut off,
and the supply current is reduced to 1 μA. Disconnecting the serial port or turning off the peripheral drivers
causes the auto-powerdown condition to occur. Auto-powerdown can be disabled when FORCEON and
FORCEOFF are high. With auto-powerdown enabled, the device is activated automatically when a valid signal is
applied to the receiver input. The INVALID output notifies the user if an RS-232 signal is present at the receiver
input. INVALID is high (valid data) if the receiver input voltage is greater than 2.7 V or less than –2.7 V, or has
been between –0.3 V and 0.3 V for less than 30 μs. INVALID is low (invalid data) if the receiver input voltage is
between –0.3 V and 0.3 V for more than 30 μs. See Figure 5 for receiver input levels.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Copyright © 2007, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
TRSF3221
3-V TO 5.5-V SINGLE-CHANNEL RS-232 COMPATIBLE LINE DRIVER/RECEIVER
SLLS857–AUGUST 2007
www.ti.com
ORDERING INFORMATION
TA
PACKAGE(1)(2)
ORDERABLE PART NUMBER
TRSF3221CDBR
TOP-SIDE MARKING
SSOP – DB
TSSOP – PW
SSOP – DB
TSSOP – PW
Reel of 2000
RT21C
0°C to 70°C
Tube of 90
TRSF3221CPW
RT21C
RT21I
RT21I
Reel of 2000
Reel of 2000
Tube of 90
TRSF3221CPWR
TRSF3221IDBR
–40°C to 85°C
TRSF3221IPW
Reel of 2000
TRSF3221IPWR
(1) Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
(2) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
FUNCTION TABLES
abc
Each Driver(1)
INPUTS
OUTPUT
DOUT
DRIVER STATUS
VALID RIN
RS-232 LEVEL
DIN
FORCEON
FORCEOFF
X
L
X
H
H
L
L
X
X
Z
H
L
Powered off
H
H
H
H
H
H
Normal operation with
auto-powerdown disabled
H
L
X
Yes
Yes
No
No
H
L
Normal operation with
auto-powerdown enabled
H
L
L
L
Z
Z
Powered off by
auto-powerdown feature
H
L
(1) H = high level, L = low level, X = irrelevant, Z = high impedance
abc
Each Receiver(1)
INPUTS
OUTPUT
ROUT
VALID RIN
RS-232 LEVEL
RIN
EN
L
H
L
L
X
X
H
L
X
H
L
X
Z
H
Open
No
(1) H = high level, L = low level, X = irrelevant, Z = high impedance (off),
Open = disconnected input or connected driver off
LOGIC DIAGRAM (POSITIVE LOGIC)
11
13
10
DIN
DOUT
16
12
FORCEOFF
FORCEON
INVALID
Auto-Powerdown
9
8
1
ROUT
RIN
EN
2
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TRSF3221
TRSF3221
3-V TO 5.5-V SINGLE-CHANNEL RS-232 COMPATIBLE LINE DRIVER/RECEIVER
www.ti.com
SLLS857–AUGUST 2007
Absolute Maximum Ratings(1)
over operating free-air temperature range (unless otherwise noted)
MIN
–0.3
–0.3
0.3
MAX UNIT
VCC
V+
Supply voltage range(2)
Positive-output supply voltage range(2)
Negative-output supply voltage range(2)
6
V
V
V
V
7
V–
–7
V+ – V– Supply voltage difference(2)
13
Driver (FORCEOFF, FORCEON, EN)
Receiver
–0.3
–25
6
25
VI
Input voltage range
V
V
Driver
–13.2
–0.3
13.2
VO
θJA
Output voltage range
Receiver (INVALID)
DB package
VCC + 0.3
82
Package thermal impedance(3)(4)
°C/W
PW package
108
TJ
Operating virtual junction temperature
Storage temperature range
150
°C
°C
Tstg
–65
150
(1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltages are with respect to network GND.
(3) Maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation at any allowable ambient
temperature is PD = (TJ(max) – TA)/θJA. Operating at the absolute maximum TJ of 150°C can affect reliability.
(4) The package thermal impedance is calculated in accordance with JESD 51-7.
Recommended Operating Conditions(1)
See Figure 6
MIN NOM
MAX UNIT
VCC = 3.3 V
VCC = 5 V
VCC = 3.3 V
VCC = 5 V
3
4.5
2
3.3
5
3.6
V
Supply voltage
5.5
Driver and control
high-level input voltage
VIH
VIL
DIN, FORCEOFF, FORCEON, EN
V
2.4
Driver and control
low-level input voltage
DIN, FORCEOFF, FORCEON, EN
DIN, FORCEOFF, FORCEON
0.8
V
VI
VI
Driver and control input voltage
Receiver input voltage
0
–25
–40
0
5.5
25
85
70
V
V
TRSF3221I
TRSF3221C
TA
Operating free-air temperature
°C
(1) Test conditions are C1–C4 = 0.1 μF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 μF, C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V.
Electrical Characteristics(1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 6)
PARAMETER
TEST CONDITIONS
MIN
TYP(2)
MAX UNIT
II
Input leakage current FORCEOFF, FORCEON, EN
±0.01
±1
μA
No load,
Auto-powerdown disabled
0.3
1
1
mA
FORCEOFF and FORCEON at VCC
Supply current
(TA = 25°C)
Powered off
No load, FORCEOFF at GND
10
ICC
No load, FORCEOFF at VCC
FORCEON at GND,
,
μA
Auto-powerdown enabled
1
10
All RIN are open or grounded
(1) Test conditions are C1–C4 = 0.1 μF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 μF, C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V.
(2) All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
Copyright © 2007, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Link(s): TRSF3221
TRSF3221
3-V TO 5.5-V SINGLE-CHANNEL RS-232 COMPATIBLE LINE DRIVER/RECEIVER
SLLS857–AUGUST 2007
www.ti.com
DRIVER SECTION
abc
Electrical Characteristics(1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 6)
PARAMETER
TEST CONDITIONS
DOUT at RL = 3 kΩ to GND, DIN = GND
DOUT at RL = 3 kΩ to GND, DIN = VCC
VI = VCC
MIN
5
TYP(2) MAX UNIT
VOH High-level output voltage
VOL Low-level output voltage
5.4
–5.4
±0.01
±0.01
±35
V
V
–5
IIH
IIL
High-level input current
Low-level input current
±1
±1
μA
μA
VI at GND
VCC = 3.6 V
±60
±90
Short-circuit
IOS
ro
VO = 0 V
mA
Ω
output current(3)
VCC = 5.5 V
±35
Output resistance
VCC, V+, and V– = 0 V,
FORCEOFF = GND
VO = ±2 V
300
10M
VO = ±12 V,
VO = ±10 V,
VCC = 3 V to 3.6 V
±25
±25
Ioff
Output leakage current
μA
VCC = 4.5 V to 5.5 V
(1) Test conditions are C1–C4 = 0.1 μF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 μF, C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V.
(2) All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
(3) Short-circuit durations should be controlled to prevent exceeding the device absolute power dissipation ratings, and not more than one
output should be shorted at a time.
Switching Characteristics(1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 6)
PARAMETER
TEST CONDITIONS
CL = 1000 pF
MIN
250
TYP(2)
MAX UNIT
Maximum data rate
(see Figure 1)
RL = 3 kΩ
CL = 250 pF,
VCC = 3 V to 4.5 V
VCC = 4.5 V to 5.5 V
See Figure 2
1000
1000
kbit/s
CL = 1000 pF,
tsk(p)
Pulse skew(3)
Slew rate,
CL = 150 pF to 2500 pF, RL = 3 kΩ to 7 kΩ,
100
ns
SR(tr) transition region
(see Figure 1)
VCC = 3.3 V, RL = 3 kΩ to 7 kΩ,
CL = 150 pF to 1000 pF
18
150 V/μs
(1) Test conditions are C1–C4 = 0.1 μF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 μF, C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V.
(2) All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
(3) Pulse skew is defined as |tPLH – tPHL| of each channel of the same device.
ESD Protection
TERMINAL
TEST CONDITIONS
TYP UNIT
NAME
NO.
DOUT
13
HBM
±15
kV
4
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TRSF3221
TRSF3221
3-V TO 5.5-V SINGLE-CHANNEL RS-232 COMPATIBLE LINE DRIVER/RECEIVER
www.ti.com
SLLS857–AUGUST 2007
RECEIVER SECTION
abc
Electrical Characteristics(1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 6)
PARAMETER
High-level output voltage
Low-level output voltage
TEST CONDITIONS
IOH = –1 mA
MIN
TYP(2)
MAX UNIT
VOH
VOL
VCC – 0.6
VCC – 0.1
V
IOL = 1.6 mA
VCC = 3.3 V
VCC = 5 V
0.4
2.4
2.4
V
1.6
1.9
VIT+
Positive-going input threshold voltage
Negative-going input threshold voltage
V
VCC = 3.3 V
VCC = 5 V
0.6
0.8
1.1
VIT–
V
1.4
Vhys
Ioff
ri
Input hysteresis (VIT+ – VIT–
Output leakage current
Input resistance
)
0.5
V
FORCEOFF = 0 V
VI = ±3 V to ±25 V
±0.05
5
±10
7
μA
kΩ
3
(1) Test conditions are C1–C4 = 0.1 μF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 μF, C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V.
(2) All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
Switching Characteristics(1)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 6)
PARAMETER
Propagation delay time, low- to high-level output
Propagation delay time, high- to low-level output
Output enable time
TEST CONDITIONS
CL = 150 pF, See Figure 3
TYP(2)
150
150
200
200
50
UNIT
ns
tPLH
tPHL
ten
CL = 150 pF, See Figure 3
CL = 150 pF, RL = 3 kΩ, See Figure 4
CL = 150 pF, RL = 3 kΩ, See Figure 4
See Figure 3
ns
ns
tdis
Output disable time
Pulse skew(3)
ns
tsk(p)
ns
(1) Test conditions are C1–C4 = 0.1 μF at VCC = 3.3 V ± 0.3 V; C1 = 0.047 μF, C2–C4 = 0.33 μF at VCC = 5 V ± 0.5 V.
(2) All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
(3) Pulse skew is defined as |tPLH – tPHL| of each channel of the same device.
ESD Protection
TERMINAL
TEST CONDITIONS
TYP UNIT
NAME
NO.
RIN
8
HBM
±15
kV
Copyright © 2007, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Link(s): TRSF3221
TRSF3221
3-V TO 5.5-V SINGLE-CHANNEL RS-232 COMPATIBLE LINE DRIVER/RECEIVER
SLLS857–AUGUST 2007
www.ti.com
AUTO-POWERDOWN SECTION
abc
Electrical Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 5)
PARAMETER
TEST CONDITIONS
MIN
MAX UNIT
Receiver input threshold
for INVALID high-level output voltage
VT+(valid)
VT–(valid)
VT(invalid)
VOH
FORCEON = GND,
FORCEOFF = VCC
FORCEOFF = VCC
FORCEOFF = VCC
2.7
0.3
0.4
V
V
V
V
V
Receiver input threshold
for INVALID high-level output voltage
FORCEON = GND,
FORCEON = GND,
–2.7
–0.3
Receiver input threshold
for INVALID low-level output voltage
IOH = –1 mA, FORCEON = GND,
FORCEOFF = VCC
INVALID high-level output voltage
INVALID low-level output voltage
VCC – 0.6
IOL = 1.6 mA, FORCEON = GND,
FORCEOFF = VCC
VOL
Switching Characteristics
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted) (see Figure 5)
PARAMETER
Propagation delay time, low- to high-level output
TYP(1)
1
UNIT
μs
tvalid
tinvalid
ten
Propagation delay time, high- to low-level output
Supply enable time
30
μs
100
μs
(1) All typical values are at VCC = 3.3 V or VCC = 5 V, and TA = 25°C.
6
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TRSF3221
TRSF3221
3-V TO 5.5-V SINGLE-CHANNEL RS-232 COMPATIBLE LINE DRIVER/RECEIVER
www.ti.com
SLLS857–AUGUST 2007
PARAMETER MEASUREMENT INFORMATION
3 V
Input
RS-232
0 V
Output
Generator
(see Note B)
50 Ω
t
t
TLH
THL
C
L
R
L
(see Note A)
V
OH
OL
3 V
3 V
−3 V
−3 V
VOLTAGE WAVEFORMS
3 V
FORCEOFF
Output
V
6 V
tTHL or tTLH
SR(tr) +
TEST CIRCUIT
NOTES: A. C includes probe and jig capacitance.
L
B. The pulse generator has the following characteristics: PRR = 250 kbit/s, Z = 50 Ω, 50% duty cycle, t ≤ 10 ns, t ≤ 10 ns.
O
r
f
Figure 1. Driver Slew Rate
3 V
0 V
Input
1.5 V
1.5 V
RS-232
Output
Generator
(see Note B)
50 Ω
C
L
t
t
PLH
PHL
R
L
(see Note A)
V
V
OH
3 V
FORCEOFF
50%
50%
VOLTAGE WAVEFORMS
Output
OL
TEST CIRCUIT
NOTES: A. C includes probe and jig capacitance.
L
B. The pulse generator has the following characteristics: PRR = 250 kbit/s, Z = 50 Ω, 50% duty cycle, t ≤ 10 ns, t ≤ 10 ns.
O
r
f
Figure 2. Driver Pulse Skew
3 V or 0 V
FORCEON
3 V
Input
1.5 V
1.5 V
−3 V
Output
Generator
(see Note B)
t
t
PLH
PHL
50 Ω
C
L
3 V
FORCEOFF
(see Note A)
V
V
OH
50%
50%
Output
OL
TEST CIRCUIT
VOLTAGE WAVEFORMS
NOTES: A. C includes probe and jig capacitance.
L
B. The pulse generator has the following characteristics: Z = 50 Ω, 50% duty cycle, t ≤ 10 ns, t ≤ 10 ns.
O
r
f
Figure 3. Receiver Propagation Delay Times
Copyright © 2007, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Link(s): TRSF3221
TRSF3221
3-V TO 5.5-V SINGLE-CHANNEL RS-232 COMPATIBLE LINE DRIVER/RECEIVER
SLLS857–AUGUST 2007
www.ti.com
PARAMETER MEASUREMENT INFORMATION (continued)
3 V
Input
1.5 V
1.5 V
V
CC
GND
0 V
(S1 at GND)
S1
3 V or 0 V
FORCEON
t
t
PZH
PHZ
(S1 at GND)
R
L
V
OH
3 V or 0 V
Output
50%
Output
0.3 V
C
L
(see Note A)
EN
t
t
PZL
PLZ
(S1 at V
)
(S1 at V )
CC
CC
Generator
(see Note B)
50 Ω
0.3 V
Output
50%
V
OL
TEST CIRCUIT
NOTES: A. C includes probe and jig capacitance.
VOLTAGE WAVEFORMS
L
B. The pulse generator has the following characteristics: Z = 50 Ω, 50% duty cycle, t ≤ 10 ns, t ≤ 10 ns.
O
r
f
C.
D.
t
t
and t
and t
are the same as t
.
dis
.
PLZ
PZL
PHZ
PZH
are the same as t
en
Figure 4. Receiver Enable and Disable Times
8
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TRSF3221
TRSF3221
3-V TO 5.5-V SINGLE-CHANNEL RS-232 COMPATIBLE LINE DRIVER/RECEIVER
www.ti.com
SLLS857–AUGUST 2007
PARAMETER MEASUREMENT INFORMATION (continued)
3 V
2.7 V
2.7 V
0 V
0 V
Receiver
Input
ROUT
−2.7 V
−2.7 V
−3 V
Generator
(see Note B)
50 Ω
t
t
valid
invalid
V
CC
50% V
t
50% V
CC
CC
INVALID
Output
0 V
Auto-
powerdown
INVALID
en
C = 30 pF
L
(see Note A)
≈V+
V+
0.3 V
V
CC
Supply
FORCEOFF
FORCEON
0 V
0.3 V
Voltages
DIN
DOUT
≈V−
V−
TEST CIRCUIT
VOLTAGE WAVEFORMS
Valid RS-232 Level, INVALID High
Indeterminate
2.7 V
0.3 V
If Signal Remains Within This Region
For More Than 30 µs, INVALID Is Low
0 V
†
−0.3 V
Indeterminate
−2.7 V
Valid RS-232 Level, INVALID High
†
Auto-powerdowndisables drivers and reduces supply
current to 1 µA.
NOTES: A. C includes probe and jig capacitance.
L
B. The pulse generator has the following characteristics: PRR = 5 kbit/s, Z = 50 Ω, 50% duty cycle, t ≤ 10 ns, t ≤ 10 ns.
O
r
f
Figure 5. INVALID Propagation Delay Times and Driver Enabling Time
Copyright © 2007, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Link(s): TRSF3221
TRSF3221
3-V TO 5.5-V SINGLE-CHANNEL RS-232 COMPATIBLE LINE DRIVER/RECEIVER
SLLS857–AUGUST 2007
www.ti.com
APPLICATION INFORMATION
1
16
15
FORCEOFF
EN
2
V
CC
C1+
V+
+
C
= 0.1 µF
BYPASS
3
−
14
Auto-
Powerdown
+
−
+
−
(1)
GND
C1
C3
4
5
C1−
C2+
13
DOUT
+
−
12
11
10
FORCEON
DIN
C2
C4
6
7
C2−
V−
−
+
INVALID
8
9
RIN
ROUT
5 kΩ
(1) C3 can be connected to V or GND.
CC
NOTES: A. Resistor values shown are nominal.
V
CC
vs CAPACITOR VALUES
V
CC
C1
C2, C3, and C4
3.3 V ± 0.3 V
5 V ± 0.5 V
3 V to 5.5 V
0.1 µF
0.047 µF
0.1 µF
0.1 µF
0.33 µF
0.47 µF
Figure 6. Typical Operating Circuit and Capacitor Values
10
Submit Documentation Feedback
Copyright © 2007, Texas Instruments Incorporated
Product Folder Link(s): TRSF3221
PACKAGE OPTION ADDENDUM
www.ti.com
24-Jul-2010
PACKAGING INFORMATION
Status (1)
Eco Plan (2)
MSL Peak Temp (3)
Samples
Orderable Device
Package Type Package
Drawing
Pins
Package Qty
Lead/
Ball Finish
(Requires Login)
Purchase Samples
Purchase Samples
Request Free Samples
TRSF3221CDB
TRSF3221CDBG4
TRSF3221CDBR
ACTIVE
ACTIVE
ACTIVE
SSOP
SSOP
SSOP
DB
DB
DB
16
16
16
TBD
TBD
Call TI
Call TI
Call TI
Call TI
2000
2000
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
TRSF3221CDBRG4
ACTIVE
SSOP
DB
16
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-1-260C-UNLIM
Request Free Samples
TRSF3221CPW
TRSF3221CPWG4
TRSF3221CPWR
TRSF3221CPWRG4
TRSF3221IDB
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
TSSOP
TSSOP
TSSOP
TSSOP
SSOP
PW
PW
PW
PW
DB
16
16
16
16
16
16
16
16
16
16
16
16
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Purchase Samples
Purchase Samples
Purchase Samples
Purchase Samples
Purchase Samples
Purchase Samples
Purchase Samples
Purchase Samples
Purchase Samples
Purchase Samples
Purchase Samples
Purchase Samples
TRSF3221IDBG4
TRSF3221IDBR
TRSF3221IDBRG4
TRSF3221IPW
SSOP
DB
SSOP
DB
SSOP
DB
TSSOP
TSSOP
TSSOP
TSSOP
PW
PW
PW
PW
TRSF3221IPWG4
TRSF3221IPWR
TRSF3221IPWRG4
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
24-Jul-2010
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Jul-2010
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TRSF3221CDBR
SSOP
DB
16
2000
330.0
16.4
8.2
6.6
2.5
12.0
16.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
23-Jul-2010
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SSOP DB 16
SPQ
Length (mm) Width (mm) Height (mm)
346.0 346.0 33.0
TRSF3221CDBR
2000
Pack Materials-Page 2
MECHANICAL DATA
MSSO002E – JANUARY 1995 – REVISED DECEMBER 2001
DB (R-PDSO-G**)
PLASTIC SMALL-OUTLINE
28 PINS SHOWN
0,38
0,22
0,65
28
M
0,15
15
0,25
0,09
5,60
5,00
8,20
7,40
Gage Plane
1
14
0,25
A
0°–ā8°
0,95
0,55
Seating Plane
0,10
2,00 MAX
0,05 MIN
PINS **
14
16
20
24
28
30
38
DIM
6,50
5,90
6,50
5,90
7,50
8,50
7,90
10,50
9,90
10,50 12,90
A MAX
A MIN
6,90
9,90
12,30
4040065 /E 12/01
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion not to exceed 0,15.
D. Falls within JEDEC MO-150
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
Amplifiers
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
www.ti.com/audio
Data Converters
DLP® Products
Automotive
www.ti.com/automotive
www.ti.com/communications
Communications and
Telecom
DSP
dsp.ti.com
Computers and
Peripherals
www.ti.com/computers
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
Consumer Electronics
Energy
www.ti.com/consumer-apps
www.ti.com/energy
Logic
Industrial
www.ti.com/industrial
Power Mgmt
Microcontrollers
RFID
power.ti.com
Medical
www.ti.com/medical
microcontroller.ti.com
www.ti-rfid.com
Security
www.ti.com/security
Space, Avionics &
Defense
www.ti.com/space-avionics-defense
RF/IF and ZigBee® Solutions www.ti.com/lprf
Video and Imaging
Wireless
www.ti.com/video
www.ti.com/wireless-apps
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2010, Texas Instruments Incorporated
相关型号:
TRSF3222
3-V TO 5.5-V TWO-CHANNEL RS-232 1-Mbit/s LINE DRIVER/RECEIVER WITH ±15-kV IEC ESD PROTECTIONWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TRSF3222E
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH ±15-kV ESD PROTECTIONWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TRSF3222ECDB
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH ±15-kV ESD PROTECTIONWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TRSF3222ECDBG4
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH ±15-kV ESD PROTECTIONWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TRSF3222ECDBR
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH ±15-kV ESD PROTECTIONWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TRSF3222ECDBRG4
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH ±15-kV ESD PROTECTIONWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TRSF3222ECDW
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH ±15-kV ESD PROTECTIONWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TRSF3222ECDWG4
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH ±15-kV ESD PROTECTIONWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TRSF3222ECDWR
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH ±15-kV ESD PROTECTIONWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TRSF3222ECDWRG4
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH ±15-kV ESD PROTECTIONWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TRSF3222ECPW
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH ±15-kV ESD PROTECTIONWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TRSF3222ECPWG4
3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER/RECEIVER WITH ±15-kV ESD PROTECTIONWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
©2020 ICPDF网 联系我们和版权申明