TSC2046EIRGVT [TI]
具有低压数字 I/O 和扩展 ESD 保护的 4 线触摸屏控制器 | RGV | 16 | -40 to 85;型号: | TSC2046EIRGVT |
厂家: | TEXAS INSTRUMENTS |
描述: | 具有低压数字 I/O 和扩展 ESD 保护的 4 线触摸屏控制器 | RGV | 16 | -40 to 85 控制器 商用集成电路 |
文件: | 总34页 (文件大小:1682K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TSC2046E
SBAS417B − JUNE 2007 − REVISED JANUARY 2008
Low Voltage I/O
TOUCH SCREEN CONTROLLER
FD EATURES
DESCRIPTION
Same Pinout as ADS7846
2.2V to 5.25V Operation
The TSC2046E is the next-generation version of the
ADS7846 4-wire touch screen controller, supporting a
low-voltage I/O interface from 1.5V to 5.25V. The
TSC2046E is 100% pin-compatible with the existing
ADS7846, and drops into the same socket. This design
allows for an easy upgrade of current applications to the
new version. The TSC2046E also has an on-chip 2.5V
reference that can be used for the auxiliary input, battery
monitor, and temperature measurement modes. The
reference can also be powered down when not used to
conserve power. The internal reference operates down to
a supply voltage of 2.7V, while monitoring the battery
voltage from 0V to 6V.
D
D
D
D
D
D
D
D
D
1.5V to 5.25V Digital I/O
Internal 2.5V Reference
Direct Battery Measurement (0V to 6V)
On-Chip Temperature Measurement
Touch-Pressure Measurement
QSPI and SPI 3-Wire Interface
Auto Power-Down
Exceeds IEC 61000-4-2 ESD Requirements
− + 15kV Contact Discharge
− No External Components Needed
Available In TSSOP-16, QFN-16, and
VFBGA-48 Packages
D
The low-power consumption of < 0.75mW typ at 2.7V
(reference off), high-speed (up to 125kHz sample rate),
and on-chip drivers make the TSC2046E an ideal choice
for battery-operated systems such as personal digital
assistants (PDAs) with resistive touch screens, pagers,
cellular phones, and other portable equipment. The
TSC2046E is available in TSSOP-16, QFN-16, and
VFBGA-48 packages and is specified over the –40°C to
+85°C temperature range.
AD PPLICATIONS
Personal Digital Assistants
D
D
D
D
D
Portable Instruments
Point-of-Sale Terminals
Pagers
Touch Screen Monitors
Cellular Phones
US Patent No. 6246394
PENIRQ
Pen Detect
+VCC
X+
Tem perature
Sensor
SAR
−
X
IOVDD
Y+
DOUT
TSC2046E
Y−
BUSY
Comparator
CS
6−Channel
MUX
Serial
Data
CDAC
In/Out
DCLK
DIN
Battery
Monitor
V
BAT
AUX
Internal 2.5V Reference
VRE F
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments
semiconductor products and disclaimers thereto appears at the end of this data sheet.
SPI and QSPI are trademarks of Motorola Inc.
Microwire is a trademark of National Semiconductor Corporation.
All other trademarks are the property of their respective owners.
ꢀꢁ ꢂ ꢃꢄ ꢅ ꢆꢇ ꢂꢈ ꢃ ꢉꢆꢉ ꢊꢋ ꢌꢍ ꢎ ꢏꢐ ꢑꢊꢍꢋ ꢊꢒ ꢓꢔ ꢎ ꢎ ꢕꢋꢑ ꢐꢒ ꢍꢌ ꢖꢔꢗ ꢘꢊꢓ ꢐꢑꢊ ꢍꢋ ꢙꢐ ꢑꢕꢚ ꢀꢎ ꢍꢙꢔ ꢓꢑꢒ
ꢓ ꢍꢋ ꢌꢍꢎ ꢏ ꢑꢍ ꢒ ꢖꢕ ꢓ ꢊ ꢌꢊ ꢓ ꢐ ꢑꢊ ꢍꢋꢒ ꢖ ꢕꢎ ꢑꢛꢕ ꢑꢕ ꢎ ꢏꢒ ꢍꢌ ꢆꢕꢜ ꢐꢒ ꢇꢋꢒ ꢑꢎ ꢔꢏ ꢕꢋꢑ ꢒ ꢒꢑ ꢐꢋꢙ ꢐꢎ ꢙ ꢝ ꢐꢎ ꢎ ꢐ ꢋꢑꢞꢚ
ꢀꢎ ꢍ ꢙꢔꢓ ꢑ ꢊꢍ ꢋ ꢖꢎ ꢍ ꢓ ꢕ ꢒ ꢒ ꢊꢋ ꢟ ꢙꢍ ꢕ ꢒ ꢋꢍꢑ ꢋꢕ ꢓꢕ ꢒꢒ ꢐꢎ ꢊꢘ ꢞ ꢊꢋꢓ ꢘꢔꢙ ꢕ ꢑꢕ ꢒꢑꢊ ꢋꢟ ꢍꢌ ꢐꢘ ꢘ ꢖꢐ ꢎ ꢐꢏ ꢕꢑꢕ ꢎ ꢒꢚ
Copyright 2007−2008, Texas Instruments Incorporated
www.ti.com
ꢆ
ꢠ
ꢅ
ꢡ
ꢢ
ꢣ
ꢤ
ꢥ
www.ti.com
SBAS417B − JUNE 2007 − REVISED JANUARY 2008
(1)
ELECTROSTATIC DISCHARGE SENSITIVITY
ABSOLUTE MAXIMUM RATINGS
+V
and IOVDD to GND . . . . . . . . . . . . . . . . . . . . . −0.3V to +6V
CC
This integrated circuit can be damaged by ESD. Texas
Instruments recommends that all integrated circuits be
Analog Inputs to GND . . . . . . . . . . . . . . . . . −0.3V to +V
CC
+ 0.3V
Digital Inputs to GND . . . . . . . . . . . . . . . . . −0.3V to IOVDD + 0.3V
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250mW
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . +150°C
Operating Temperature Range . . . . . . . . . . . . . . . . −40°C to +85°C
Storage Temperature Range . . . . . . . . . . . . . . . . . −65°C to +150°C
Lead Temperature (soldering, 10s) . . . . . . . . . . . . . . . . . . . . . +300°C
handledwith appropriate precautions. Failure to observe
proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to
complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could
cause the device not to meet its published specifications.
(2)
IEC Contact Discharge (X+, X−, Y+, Y−)
. . . . . . . . . . . . . . . 15kV
(1)
Stresses above these ratings may cause permanent damage.
Exposure to absolute maximum conditions for extended periods
may degrade device reliability. These are stress ratings only, and
functional operation of the device at these or any other conditions
beyond those specified is not implied.
(2)
Test method based on IEC standard 61000−4−2. Contact Texas
Instruments for test details.
(1)
PACKAGE/ORDERING INFORMATION
NOMINAL
PENIRQ
PULLUP
RESISTOR
VALUES
MAXIMUM
INTEGRAL
LINEARITY
ERROR
SPECIFIED
PACKAGE-
LEAD
PACKAGE
DESIGNATOR
PACKAGE
MARKING
ORDERING
NUMBER
TRANSPORT
MEDIA, QUANTITY
TEMPERATURE
RANGE
(LSB)
PRODUCT
TSC2046EIPW
Rails, 100
TSSOP-16
PW
−40°C to +85°C
TSC2046EI
TSC2046EIPWR
Tape and Reel, 2500
4x4, 0.8mm
Thin
QFN-16
TSC2046EIRGVT
TSC2046EIRGVR
Tape and Reel, 250
Tape and Reel, 2500
TSC2046E
50kΩ
2
RGV
ZQC
−40°C to +85°C
−40°C to +85°C
TSC2046E
BC2046E
4x4
VFBGA-48
TSC2046EIZQCR
Tape and Reel, 2500
(1)
For the most current package and ordering information, see the Package Option Addendum located at the end of this data sheet, or see the TI web
site at www.ti.com.
2
ꢆꢠ ꢅꢡ ꢢꢣ ꢤ ꢥ
www.ti.com
SBAS417B − JUNE 2007 − REVISED JANUARY 2008
ELECTRICAL CHARACTERISTICS: V = +2.7V to +5.5V
S
At T = −40°C to +85°C, +V
= +2.7V, V
= 2.5V internal voltage, f = 125kHz, f
= 16 • f = 2MHz, 12-bit mode, digital
SAMPLE
A
CC
REF
SAMPLE CLK
inputs = GND or IOVDD, and +V
must be ≥ IOVDD, unless otherwise noted.
CC
TSC2046E
TYP
PARAMETER
CONDITION
MIN
MAX
UNITS
ANALOG INPUT
Full-Scale Input Span
Absolute Input Range
Positive Input−Negative Input
Positive Input
0
V
V
V
REF
+ 0.2
−0.2
−0.2
+V
CC
+0.2
Negative Input
V
Capacitance
25
pF
µA
Leakage Current
0.1
SYSTEM PERFORMANCE
Resolution
12
Bits
Bits
No Missing Codes
Integral Linearity Error
Offset Error
11
(1)
2
6
4
LSB
LSB
Gain Error
External V
REF
LSB
µVrms
dB
Noise
Including Internal V
70
70
REF
Power-Supply Rejection
SAMPLING DYNAMICS
Conversion Time
12
CLK Cycles
Acquisition Time
3
CLK Cycles
Throughput Rate
125
kHz
ns
Multiplexer Settling Time
Aperture Delay
500
30
ns
Aperture Jitter
100
100
ps
Channel-to-Channel Isolation
V
= 2.5V
PP
at 50kHz
dB
IN
SWITCH DRIVERS
On-Resistance
Y+, X+
5
6
Ω
Ω
mA
Y−, X−
(2)
Drive Current
Duration 100ms
50
REFERENCE OUTPUT
Internal Reference Voltage
Internal Reference Drift
Quiescent Current
2.45
1.0
2.50
15
2.55
V
ppm/°C
µA
500
REFERENCE INPUT
Range
+V
CC
V
Input Impedance
SER/DFR = 0, PD1 = 0
Internal Reference Off
Internal Reference On
1
GΩ
250
Ω
BATTERY MONITOR
Input Voltage Range
Input Impedance
Sampling Battery
Battery Monitor Off
Accuracy
0.5
6.0
V
10
1
kΩ
GΩ
%
V
= 0.5V to 5.5V, External V
REF
= 2.5V
−2
−3
+2
+3
BAT
V
= 0.5V to 5.5V, Internal Reference
%
BAT
TEMPERATURE MEASUREMENT
Temperature Range
−40
+85
°C
°C
°C
°C
°C
(3)
Resolution
Differential Method
1.6
0.3
2
(4)
TEMP0
(3)
Accuracy
Differential Method
(4)
TEMP0
3
(1)
LSB means Least Significant Bit. With V
= +2.5V, 1 LSB is 610µV.
REF
(2)
(3)
(4)
(5)
(6)
(7)
Assured by design, but not tested. Exceeding 50mA source current may result in device degradation.
Difference between TEMP0 and TEMP1 measurement, no calibration necessary.
Temperature drift is −2.1mV/°C.
TSC2046E operates down to 2.2V.
IOVDD must be ≤ (+V ).
Combined supply current from +V
CC
and IOVDD. Typical values obtained from conversions on AUX input with PD0 = 0.
CC
3
ꢆꢠ ꢅ ꢡꢢꢣ ꢤ ꢥ
www.ti.com
SBAS417B − JUNE 2007 − REVISED JANUARY 2008
ELECTRICAL CHARACTERISTICS: V = +2.7V to +5.5V (continued)
S
At T = −40°C to +85°C, +V
= +2.7V, V
= 2.5V internal voltage, f = 125kHz, f
= 16 • f
SAMPLE
= 2MHz, 12-bit mode, digital
A
CC
REF
SAMPLE CLK
inputs = GND or IOVDD, and +V
must be ≥ IOVDD, unless otherwise noted.
CC
TSC2046E
TYP
PARAMETER
CONDITION
MIN
MAX
UNITS
DIGITAL INPUT/OUTPUT
Logic Family
CMOS
5
Capacitance
All Digital Control Input Pins
15
pF
V
V
V
V
V
| I | ≤ +5µA
IOVDD • 0.7
−0.3
IOVDD + 0.3
0.3 • IOVDD
IH
IH
| I | ≤ +5µA
IL
V
IL
I
= −250µA
IOVDD • 0.8
V
OH
OL
OH
I
= 250µA
0.4
V
OL
Straight
Binary
Data Format
POWER-SUPPLY REQUIREMENTS
(5)
+V
CC
Specified Performance
Operating Range
2.7
2.2
1.5
3.6
V
V
5.25
(6)
IOVDD
+V
V
CC
(7)
Quiescent Current
Internal Reference Off
Internal Reference On
280
780
220
650
µA
µA
µA
µA
f
= 12.5kHz
SAMPLE
Power-Down Mode with
3
CS = DCLK = DIN = IOVDD
Power Dissipation
+V
CC
= +2.7V
1.8
mW
TEMPERATURE RANGE
Specified Performance
−40
+85
°C
(1)
LSB means Least Significant Bit. With V
= +2.5V, 1 LSB is 610µV.
REF
(2)
(3)
(4)
(5)
(6)
(7)
Assured by design, but not tested. Exceeding 50mA source current may result in device degradation.
Difference between TEMP0 and TEMP1 measurement, no calibration necessary.
Temperature drift is −2.1mV/°C.
TSC2046E operates down to 2.2V.
IOVDD must be ≤ (+V ).
Combined supply current from +V
CC
and IOVDD. Typical values obtained from conversions on AUX input with PD0 = 0.
CC
4
ꢆꢠ ꢅꢡ ꢢꢣ ꢤ ꢥ
www.ti.com
SBAS417B − JUNE 2007 − REVISED JANUARY 2008
PIN CONFIGURATION
Top View
TSSOP
Top View
VFBGA
DCLK CS
DIN BUSY DOUT
1
2
3
4
5
6
7
+VCC
X+
1
2
3
4
5
6
7
8
16 DCLK
15 CS
NC
NC
A
B
C
D
E
F
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
+VCC
+VCC
PENIRQ
IOVDD
Y+
14 DIN
−
−
X
Y
13 BUSY
12 DOUT
11 PENIRQ
10 IOVDD
TSC2046E
NC
NC
X+
Y+
VREF
AUX
GND
VBAT
AUX
NC
NC
NC
NC
NC
NC
NC
NC
NC
9
VREF
G
X−
Y− GND GND VBAT
Top View
QFN
1
2
3
4
12 AUX
11 VBAT
10 GND
BUSY
DIN
TSC2046E
CS
(1)
(Thermal Pad)
9
−
Y
DCLK
(1)
The thermal pad is internally connected to the substrate. This pad can be connected to the analog ground or left floating. Keep the thermal
pad separate from the digital ground, if possible.
PIN DESCRIPTION
TSSOP PIN #
VFBGA PIN #
QFN PIN #
NAME
DESCRIPTION
1
2
B1 and C1
5
6
+V
Power Supply
CC
X+
D1
E1
X+ Position Input
Y+ Position Input
X− Position Input
Y− Position Input
Ground
3
7
Y+
X−
4
G2
8
5
G3
9
Y−
6
G4 and G5
G6
10
11
12
13
14
15
16
GND
7
V
Battery Monitor Input
Auxiliary Input to ADC
Voltage Reference Input/Output
Digital I/O Power Supply
Pen Interrupt
BAT
AUX
8
E7
9
D7
V
REF
10
11
12
C7
IOVDD
B7
PENIRQ
DOUT
A6
Serial Data Output. Data are shifted on the falling edge of DCLK. This output is high
impedance when CS is high.
13
14
15
A5
A4
A3
1
2
3
BUSY
DIN
Busy Output. This output is high impedance when CS is high.
Serial Data Input. If CS is low, data sre latched on the rising edge of DCLK.
CS
Chip Select Input. Controls conversion timing and enables the serial input/output register.
CS high = power-down mode (ADC only).
16
A2
4
DCLK
External Clock Input. This clock runs the SAR conversion process and synchronizes serial
data I/O.
5
ꢆꢠ ꢅ ꢡꢢꢣ ꢤ ꢥ
www.ti.com
SBAS417B − JUNE 2007 − REVISED JANUARY 2008
TYPICAL CHARACTERISTICS
At T = +25°C, +V
CC
= +2.7V, IOVDD = +1.8V, V
REF
= External +2.5V, 12-bit mode, PD0 = 0, f
SAMPLE
= 125kHz, and f
CLK
= 16 • f = 2MHz,
SAMPLE
A
unless otherwise noted.
+V SUPPLY CURRENT vs TEMPERATURE
IOVDD SUPPLY CURRENT vs TEMPERATURE
CC
400
350
300
250
200
150
100
30
25
20
15
10
5
−
−
20
40
0
20
40
60
80
100
−
−
20
40
0
20
40
60
80
100
Temperature (°C)
Temperature (°C)
+VCC SUPPLY CURRENT vs +VCC
POWER−DOWN SUPPLY CURRENT vs TEMPERATURE
450
400
350
300
250
200
150
100
140
120
100
80
fSAMPLE = 125kHz
fSAMPLE = 12.5kHz
60
40
2.0
2.5
3.0
3.5
4.0
4.5
5.0
−
−
20
40
0
20
40
60
80
100
+VCC (V)
Temperature (°C)
MAXIMUM SAMPLE RATE vs +VCC
IOVDD SUPPLY CURRENT vs IOVDD
1M
100k
10k
1k
60
50
40
30
20
10
0
≥
+VCC IOVDD
fSAMPLE = 125kHz
fSAMPLE = 12.5kHz
2.0
2.5
3.0
3.5
4.0
4.5
5.0
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
+VCC (V)
IOVDD (V)
6
ꢆꢠ ꢅꢡ ꢢꢣ ꢤ ꢥ
www.ti.com
SBAS417B − JUNE 2007 − REVISED JANUARY 2008
TYPICAL CHARACTERISTICS (continued)
At T = +25°C, +V
unless otherwise noted.
= +2.7V, IOVDD = +1.8V, V
= External +2.5V, 12-bit mode, PD0 = 0, f
SAMPLE
= 125kHz, and f
CLK
= 16 • f = 2MHz,
SAMPLE
A
CC REF
CHANGE IN GAIN vs TEMPERATURE
CHANGE IN OFFSET vs TEMPERATURE
0.15
0.10
0.05
0
0.6
0.4
0.2
0
−
−
−
0.05
0.10
0.15
−
−
−
0.2
0.4
0.6
−
−
20
40
0
20
40
60
80
100
−
−
20
40
0
20
40
60
80
100
Temperature (°C)
Temperature (°C)
REFERENCE CURRENT vs SAMPLE RATE
REFERENCE CURRENT vs TEMPERATURE
14
12
10
8
18
16
14
12
10
8
6
4
2
0
6
−
−
20
40
0
20
40
60
80
100
0
25
50
75
100
125
Temperature (°C)
Sample Rate (kHz)
SWITCH ON− RESISTANCE vs +VCC
SWITCH ON−RESISTANCE vs TEMPERATURE
−
−
(X+, Y+: +VCC to Pin; X , Y : Pin to GND)
−
−
(X+, Y+: +VCC to Pin; X , Y : Pin to GND)
8
7
6
5
4
3
8
7
6
5
4
3
2
1
−
Y
−
Y
X+, Y+
−
X
−
X
X+, Y+
2.0
2.5
3.0
3.5
+VCC (V)
4.0
4.5
5.0
−
−
20
40
0
20
40
60
80
100
Temperature (°C)
7
ꢆ
ꢠ
ꢅ
ꢡ
ꢢ
ꢣ
ꢤ
ꢥ
www.ti.com
SBAS417B − JUNE 2007 − REVISED JANUARY 2008
TYPICAL CHARACTERISTICS (continued)
At T = +25°C, +V
unless otherwise noted.
= +2.7V, IOVDD = +1.8V, V
= External +2.5V, 12-bit mode, PD0 = 0, f
SAMPLE
= 125kHz, and f
CLK
= 16 • f = 2MHz,
SAMPLE
A
CC REF
INTERNAL VREF vs TEMPERATURE
MAXIMUM SAMPLING RATE vs RIN
2.5080
2.5075
2.5070
2.5065
2.5060
3.5055
2.5050
2.5045
2.5040
2.5035
2.5030
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
Ω
INL: RIN = 500
INL: RIN = 2k
Ω
Ω
DNL: RIN = 500
Ω
DNL: RIN = 2k
20
40
60
80
100 120 140 160 180 200
Sampling Rate (kHz)
Temperature (°C)
INTERNAL VREF vs +VCC
INTERNAL V
vs TURN−ON TIME
REF
2.510
2.505
2.500
2.495
2.490
2.485
2.480
100
80
60
40
20
0
No Cap
(42µs)
12-Bit Settling
1µF Cap
(124µs)
12-Bit Settling
2.5
3.0
3.5
4.0
+VCC (V)
4.5
5.0
0
200
400
600
800
1000
1200
1400
Turn-On Time (µs)
TEMP DIODE VOLTAGE vs TEMPERATURE
TEMP0 DIODE VOLTAGE vs +VCC
850
800
750
700
650
600
550
500
450
604
602
600
598
596
594
90.1mV
TEMP1
135.1mV
TEMP0
2.7
3.0
3.3
+VCC (V)
Temperature (°C)
8
ꢆꢠ ꢅꢡ ꢢꢣ ꢤ ꢥ
www.ti.com
SBAS417B − JUNE 2007 − REVISED JANUARY 2008
TYPICAL CHARACTERISTICS (continued)
At T = +25°C, +V
CC
= +2.7V, IOVDD = +1.8V, V
REF
= External +2.5V, 12-bit mode, PD0 = 0, f
SAMPLE
= 125kHz, and f
CLK
= 16 • f = 2MHz,
SAMPLE
A
unless otherwise noted.
TEMP1 DIODE VOLTAGE vs +VCC
720
718
716
714
712
710
2.7
3.0
3.3
+VCC (V)
The analog input (X-, Y-, and Z-Position coordinates,
auxiliary input, battery voltage, and chip temperature)
to the converter is provided via a multiplexer. A unique
configuration of low on-resistance touch panel driver
switches allows an unselected ADC input channel to
provide power and the accompanying pin to provide
ground for an external device, such as a touch screen.
By maintaining a differential input to the converter and
a differential reference architecture, it is possible to
negate the error from each touch panel driver switch
on-resistance (if this is a source of error for the
particular measurement).
THEORY OF OPERATION
The TSC2046E is a classic successive approximation
register (SAR) analog-to-digital converter (ADC). The
architecture is based on capacitive redistribution, which
inherently includes a sample-and-hold function. The
converter is fabricated on a 0.6µm CMOS process.
The basic operation of the TSC2046E is shown in
Figure 1. The device features an internal 2.5V reference
and uses an external clock. Operation is maintained from
a single supply of 2.7V to 5.25V. The internal reference can
be overdriven with an external, low-impedance source
between 1V and +VCC. The value of the reference voltage
directly sets the input range of the converter.
+2.7V to +5V
TSC2046E
B1 +VCC DCLK A2
µ
1 F
to
+
Serial/Conversion Clock
Chip Select
µ
0.1 F
µ
10 F
C1
D1
E1
G2
G3
G6
E7
A3
A4
A5
+VCC
X+
CS
DIN
(Optional)
Serial Data In
Converter Status
Serial Data Out
Pen Interrupt
Y+
BUSY
Touch
Screen
−
−
X
Y
DOUT A6
B7
C7
D7
PENIRQ
IOVDD
VREF
To Battery
VBAT
AUX
Auxiliary Input
G4
G5
GND
GND
Voltage
Regulator
NOTE: VFBGA package and pin names shown.
Figure 1. Basic Operation of the TSC2046E
9
ꢆꢠ ꢅ ꢡꢢꢣ ꢤ ꢥ
www.ti.com
SBAS417B − JUNE 2007 − REVISED JANUARY 2008
When the converter enters the hold mode, the voltage
difference between the +IN and –IN inputs (shown in
Figure 2) is captured on the internal capacitor array. The
input current into the analog inputs depends on the
conversion rate of the device. During the sample period, the
source must charge the internal sampling capacitor (typically
25pF). After the capacitor is fully charged, there is no further
input current. The rate of charge transfer from the analog
source to the converter is a function of conversion rate.
ANALOG INPUT
Figure 2 shows a block diagram of the input multiplexer on
the TSC2046E, the differential input of the ADC, and the
differential reference of the converter. Table 1 and Table 2
show the relationship between the A2, A1, A0, and
SER/DFR control bits and the configuration of the
TSC2046E. The control bits are provided serially via the DIN
pin—see the Digital Interface section of this data sheet for
more details.
+V
V
PENIRQ IOVDD
CC
REF
TEMP1
TEMP0
Level
Shifter
Ω
or
50k
90kΩ
Logic
A2− A0
SER/DFR
(Shown 001 )
(Shown Low)
B
X+
X−
Ref On/Off
Y+
+REF
ADC
−REF
+IN
−
Y
−IN
2.5V
Reference
7.5kΩ
V
BAT
Ω
2.5k
Battery
On
AUX
GND
Figure 2. Simplified Diagram of Analog Input
A2 A1 A0
V
AUX
IN
TEMP
Y−
X+
+IN
+IN
Y+ Y-POSITION X-POSITION Z -POSITION Z -POSITION X-DRIVERS Y-DRIVERS
1 2
BAT
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
+IN (TEMP0)
Off
Off
Measure
Off
On
+IN
Off
Off
Measure
X−, On
X−, On
On
Y+, On
Y+, On
Off
+IN
Measure
+IN
Measure
+IN
Off
Off
+IN (TEMP1)
Off
Off
Table 1. Input Configuration (DIN), Single-Ended Reference Mode (SER/DFR high)
A2
A1
A0
1
+REF
Y+
−REF
Y−
Y−
X+
+IN
+IN
Y+
Y-POSITION
X-POSITION
Z -POSITION
1
Z -POSITION
2
DRIVERS
Y+, Y−
Y+, X−
Y+, X−
X+, X−
0
0
1
1
0
1
0
0
Measure
1
Y+
X−
Measure
0
Y+
X−
+IN
Measure
1
X+
X−
+IN
Measure
Table 2. Input Configuration (DIN), Differential Reference Mode (SER/DFR low)
10
ꢆꢠ ꢅꢡ ꢢꢣ ꢤ ꢥ
www.ti.com
SBAS417B − JUNE 2007 − REVISED JANUARY 2008
There is also a critical item regarding the reference when
making measurements while the switch drivers are ON. For
this discussion, it is useful to consider the basic operation of
the TSC2046E (see Figure 1). This particular application
shows the device being used to digitize a resistive touch
screen. A measurement of the current Y-Position of the
pointing device is made by connecting the X+ input to the
ADC, turning on the Y+ and Y– drivers, and digitizing the
voltage on X+ (Figure 4 shows a block diagram). For this
measurement, the resistance in the X+ lead does not affect
the conversion (it does affect the settling time, but the
resistance is usually small enough that this is not a concern).
However, because the resistance between Y+ and Y– is
fairly low, the on-resistance of the Y drivers does make a
small difference. Under the situation outlined so far, it is not
possible to achieve a 0V input or a full-scale input regardless
of where the pointing device is on the touch screen because
some voltage is lost across the internal switches. In addition,
the internal switch resistance is unlikely to track the
resistance of the touch screen, providing an additional
source of error.
INTERNAL REFERENCE
The TSC2046E has an internal 2.5V voltage reference that
can be turned on or off with the control bit, PD1 (see Table 5
and Figure 3). Typically, the internal reference voltage is only
used in the single-ended mode for battery monitoring,
temperature measurement, and for using the auxiliary input.
Optimal touch screen performance is achieved when using
the differential mode. The internal reference voltage of the
TSC2046E must be commanded to be off to maintain
compatibility with the ADS7843. Therefore, after power-up,
a write of PD1 = 0 is required to ensure the reference is off
(see the Typical Characteristics for power-up time of the
reference from power-down).
Reference
Power−Down
VREF
Band
Buffer
Gap
+VCC
VREF
Optional
To
CDAC
Y+
X+
Figure 3. Simplified Diagram of the Internal
Reference
+REF
+IN
REFERENCE INPUT
Converter
The voltage difference between +REF and –REF (see
Figure 2) sets the analog input range. The TSC2046E
operates with a reference in the range of 1V to +VCC. There
are several critical items concerning the reference input
and its wide voltage range. As the reference voltage is
reduced, the analog voltage weight of each digital output
code (referred to as LSB size) is also reduced. The LSB
(least significant bit) size is equal to the reference voltage
divided by 4096 in 12-bit mode. Any offset or gain error
inherent in the ADC appears to increase, in terms of LSB
size, as the reference voltage is reduced. For example, if
the offset of a given converter is 2LSBs with a 2.5V
reference, it is typically 5LSBs with a 1V reference. In each
case, the actual offset of the device is the same, 1.22mV.
With a lower reference voltage, more care must be taken
to provide a clean layout including adequate bypassing, a
clean (low-noise, low-ripple) power supply, a low-noise
reference (if an external reference is used), and a
low-noise input signal.
−
IN
−
REF
−
Y
GND
Figure 4. Simplified Diagram of Single-Ended
Reference (SER/DFR high, Y switches enabled,
X+ is analog input)
This situation can be remedied as shown in Figure 5. By
setting the SER/DFR bit low, the +REF and –REF inputs
are connected directly to Y+ and Y–, respectively, making
the analog-to-digital conversion ratiometric. The result of
the conversion is always a percentage of the external
resistance, regardless of how it changes in relation to the
on-resistance of the internal switches. Note that there is an
important consideration regarding power dissipation when
using the ratiometric mode of operation (see the Power
Dissipation section for more details).
The voltage into the VREF input directly drives the
capacitor digital-to-analog converter (CDAC) portion of the
TSC2046E. Therefore, the input current is very low
(typically < 13µA).
11
ꢆꢠ ꢅ ꢡꢢꢣ ꢤ ꢥ
www.ti.com
SBAS417B − JUNE 2007 − REVISED JANUARY 2008
+VCC
TSC2046E data rate. Once the required number of
conversions have been made, the processor commands
the TSC2046E to go into its power-down state on the last
measurement. This process is required for X-Position,
Y-Position, and Z-Position measurements. Option 3 is to
operate in the 15 Clock-per-Conversion mode, which
overlaps the analog-to-digital conversions and maintains
the touch screen drivers on until commanded to stop by the
processor (see Figure 13).
Y+
X+
+REF
+IN
Converter
TEMPERATURE MEASUREMENT
−
IN
−
REF
−
Y
In some applications, such as battery recharging, a
measurement of ambient temperature is required. The
temperature measurement technique used in the
TSC2046E relies on the characteristics of
a
GND
semiconductor junction operating at a fixed current level.
The forward diode voltage (VBE) has a well-defined
characteristic versus temperature. The ambient
temperature can be predicted in applications by knowing
the +25°C value of the VBEvoltage and then monitoring the
delta of that voltage as the temperature changes. The
TSC2046E offers two modes of operation. The first mode
requires calibration at a known temperature, but only
Figure 5. Simplified Diagram of Differential
Reference (SER/DFR low, Y switches enabled,
X+ is analog input)
As a final note about the differential reference mode, it
must be used with +VCCas the source of the +REF voltage
and cannot be used with VREF. It is possible to use a
high-precision reference on VREF and single-ended
reference mode for measurements that do not need to be
ratiometric. In some cases, it is possible to power the
converter directly from a precision reference. Most
references can provide enough power for the TSC2046E,
but might not be able to supply enough current for the
external load (such as a resistive touch screen).
requires
a single reading to predict the ambient
temperature. A diode is used (turned on) during this
measurement cycle. The voltage across the diode is
connected through the MUX for digitizing the forward bias
voltage by the ADC with an address of A2 = 0, A1 = 0, and
A0 = 0 (see Table 1 and Figure 6 for details). This voltage
is typically 600mV at +25°C with a 20µA current through
the diode. The absolute value of this diode voltage can
vary by a few millivolts. However, the temperature
TOUCH SCREEN SETTLING
coefficient (T ) of this voltage is very consistent at
C
–2.1mV/°C. During the final test of the end product, the
diode voltage would be stored at a known room
temperature, in memory, for calibration purposes by the
user. The result is an equivalent temperature
measurement resolution of 0.3°C/LSB (in 12-bit mode).
In some applications, external capacitors may be required
across the touch screen for filtering noise picked up by the
touch screen (for example, noise generated by the LCD
panel or backlight circuitry). These capacitors provide a
low-pass filter to reduce the noise, but cause a settling time
requirement when the panel is touched that typically
shows up as a gain error. There are several methods for
minimizing or eliminating this issue. The problem is that
the input and/or reference has not settled to the final
steady-state value prior to the ADC sampling the input(s)
and providing the digital output. Additionally, the reference
voltage may still be changing during the measurement
cycle. Option 1 is to stop or slow down the TSC2046E
DCLK for the required touch screen settling time. This
option allows the input and reference to have stable values
for the Acquire period (3 clock cycles of the TSC2046E;
see Figure 9). This option works for both the single-ended
and the differential modes. Option 2 is to operate the
TSC2046E in the differential mode only for the touch
screen measurements and command the TSC2046E to
remain on (touch screen drivers ON) and not go into
power-down (PD0 = 1). Several conversions are made,
depending on the settling time required and the
+VCC
TEMP0
TEM P1
MUX
ADC
Figure 6. Functional Block Diagram of
Temperature Measurement
12
ꢆꢠ ꢅꢡ ꢢꢣ ꢤ ꢥ
www.ti.com
SBAS417B − JUNE 2007 − REVISED JANUARY 2008
The second mode of operation does not require a test
temperature calibration, but uses a two-measurement
method to eliminate the need for absolute temperature
calibration and for achieving 2°C accuracy. This mode
requires a second conversion with an address of A2 = 1,
A1 = 1, and A0 = 1, with a 91 times larger current. The voltage
difference between the first and second conversion using 91
times the bias current is represented by Equation (1):
BATTERY MEASUREMENT
An added feature of the TSC2046E is the ability to monitor
the battery voltage on the other side of the voltage regulator
(dc/dc converter), as shown in Figure 7. The battery voltage
can vary from 0V to 6V, while maintaining the voltage to the
TSC2046E at 2.7V, 3.3V, etc. The input voltage (VBAT) is
divided down by four so that a 5.5V battery voltage is
represented as 1.375V to the ADC. This design simplifies the
multiplexer and control logic. In order to minimize the power
consumption, the divider is only on during the sampling
period when A2 = 0, A1 = 1, and A0 = 0 (see Table 1 for the
relationship between the control bits and configuration of the
TSC2046E).
kT
q
DV +
@ In(N)
(1)
where:
N is the current ratio = 91.
k = Boltzmann’s constant = 1.3807 × 10−23 J/K
(joules/kelvins).
q = the electron charge = 1.6022 × 10–19 C (coulombs).
2.7V
DC/DC
Converter
Battery
T = the temperature in kelvins (K).
+
0.5V
to
5.5V
This method can provide improved absolute temperature
measurement, but at a lower resolution of 1.6°C/LSB. The
resulting equation that solves for T is:
+V
CC
q @ DV
T +
k @ In(N)
(2)
0.125V to 1.375V
V
BAT
ADC
where:
Ω
Ω
7.5k
2.5k
∆V = VBE(TEMP1) – VBE(TEMP0) (in mV)
∴ T = 2.573 ⋅ ∆V (in K)
or T = 2.573 ⋅ ∆V – 273 (in °C)
NOTE: The bias current for each diode temperature
measurement is only on for three clock cycles (during the
acquisition mode) and, therefore, does not add any
noticeable increase in power, especially if the temperature
measurement only occurs occasionally.
Figure 7. Battery Measurement Functional Block
Diagram
13
ꢆꢠ ꢅ ꢡꢢꢣ ꢤ ꢥ
www.ti.com
SBAS417B − JUNE 2007 − REVISED JANUARY 2008
PRESSURE MEASUREMENT
DIGITAL INTERFACE
Measuring touch pressure can also be done with the
TSC2046E. To determine pen or finger touch, the pressure
of the touch needs to be determined. Generally, it is not
necessary to have very high performance for this test;
therefore, the 8-bit resolution mode is recommended
(however, calculations shown here are in the 12-bit
resolution mode). There are several different ways of
performing this measurement. The TSC2046E supports
two methods. The first method requires knowing the
X-plate resistance, measurement of the X-Position, and
two additional cross panel measurements (Z1 and Z2) of
the touch screen, as shown in Figure 8. Using Equation (3)
calculates the touch resistance:
See Figure 9 for the typical operation of the TSC2046E
digital interface. This diagram assumes that the source of
the digital signals is a microcontroller or digital signal
processor with
a
basic serial interface. Each
communication between the processor and the converter,
such as SPI, SSI, or Microwiret synchronous serial
interface, consists of eight clock cycles. One complete
conversion can be accomplished with three serial
communications for a total of 24 clock cycles on the DCLK
input.
The first eight clock cycles are used to provide the control
byte via the DIN pin. When the converter has enough
information about the following conversion to set the input
multiplexer and reference inputs appropriately, the
converter enters the acquisition (sample) mode and, if
needed, the touch panel drivers are turned on. After three
more clock cycles, the control byte is complete and the
converter enters the conversion mode. At this point, the
input sample-and-hold goes into the hold mode and the
touch panel drivers turn off (in single-ended mode). The
next 12 clock cycles accomplish the actual analog-
to-digital conversion. If the conversion is ratiometric
(SER/DFR = 0), the drivers are on during the conversion
and a 13th clock cycle is needed for the last bit of the
conversion result. Three more clock cycles are needed to
complete the last byte (DOUT will be low), which are
ignored by the converter.
Z2
Z1
X−Position
4096
ǒ Ǔ
RTOUCH + RX−Plate
@
*1
(3)
The second method requires knowing both the X-plate
and Y-plate resistance, measurement of X-Position and
Y-Position, and Z1. Using Equation (4) also calculates
the touch resistance:
RX−Plate @ X−Position
4096
Z1
ǒ Ǔ
RTOUCH
+
*1
4096
Y−Position
ǒ1*
Ǔ
*RY−Plate
4096
(4)
Measure
Measure
X−Position
Z1−P o s it io n
Y+
X+
X+
Y+
Y+
X+
Touch
Touch
Touch
Z2−P o s it io n
X−Position
Z1−Position
−
X
−
Y
Measure
Z2−P o s it io n
−
−
X
−
Y
−
Y
X
Figure 8. Pressure Measurement Block Diagrams
14
ꢆꢠ ꢅꢡ ꢢꢣ ꢤ ꢥ
www.ti.com
SBAS417B − JUNE 2007 − REVISED JANUARY 2008
mode, the converter reference voltage is always the
difference between the VREF and GND pins (see Table 1
and Table 2, and Figure 2 through Figure 5, for further
information).
Control Byte
The control byte (on DIN), as shown in Table 3, provides
the start conversion, addressing, ADC resolution,
configuration, and power-down of the TSC2046E.
Figure 9, Table 3 and Table 4 give detailed information
regarding the order and description of these control bits
within the control byte.
BIT 7
(MSB)
BIT 0
(LSB)
BIT 6 BIT 5 BIT 4
A2 A1 A0
BIT 3
BIT 2
BIT 1
S
MODE SER/DFR PD1
PD0
Initiate START—The first bit, the S bit, must always be
high and initiates the start of the control byte. The
TSC2046E ignores inputs on the DIN pin until the start bit
is detected.
Table 3. Order of the Control Bits in the Control
Byte
BIT
NAME
DESCRIPTION
Addressing—The next three bits (A2, A1, and A0) select
the active input channel(s) of the input multiplexer (see
Table 1, Table 2, and Figure 2), touch screen drivers, and
the reference inputs.
7
S
Start bit. Control byte starts with first high bit on DIN.
A new control byte can start every 15th clock cycle
in 12-bit conversion mode or every 11th clock cycle
in 8-bit conversion mode (see Figure 13).
6-4
A2-A0
MODE
Channel Select bits. Along with the SER/DFR bit,
these bits control the setting of the multiplexer input,
touch driver switches, and reference inputs (see
Table 1 and Figure 13).
MODE—The mode bit sets the resolution of the ADC. With
this bit low, the next conversion has 12-bit resolution,
whereas with this bit high, the next conversion has 8-bit
resolution.
3
2
12-Bit/8-Bit Conversion Select bit. This bit controls
the number of bits for the next conversion: 12-bits
(low) or 8-bits (high).
SER/DFR—The SER/DFR bit controls the reference
mode, either single-ended (high) or differential (low). The
differential mode is also referred to as the ratiometric
conversion mode and is preferred for X-Position,
Y-Position, and Pressure-Touch measurements for
optimum performance. The reference is derived from the
voltage at the switch drivers, which is almost the same as
the voltage to the touch screen. In this case, a reference
voltage is not needed as the reference voltage to the ADC
is the voltage across the touch screen. In the single-ended
SER/DFR Single-Ended/Differential Reference Select bit. Along
with bits A2-A0, this bit controls the setting of the
multiplexer input, touch driver switches, and
reference inputs (see Table 1 and Table 2).
1-0
PD1-PD0 Power-Down Mode Select bits. Refer to Table 5 for
details.
Table 4. Descriptions of the Control Bits within
the Control Byte
CS
tACQ
DCLK
DIN
1
8
1
8
1
8
SER/
DFR
S
A2 A1 A0 MODE
PD1 PD0
Acquire
(START)
Idle
Conversion
Idle
BUSY
DOUT
11 10
(MSB)
9
8
7
6
5
4
3
2
1
0
Zero Filled...
(LSB)
Drivers 1 and 2(1)
(SER/DFR High)
Off
Off
On
Off
Drivers 1 and 2(1, 2)
(SER/DFR Low)
On
Off
−
NOTES: (1) For Y−Position, Driver 1 is on X+ is selected, and Driver 2 is off. For X−Position, Driver 1 is off, Y+ is selected, and Driver 2 is on. Y will turn on
when power−down mode is entered and PD0 = 0.
(2) Drivers will remain on if PD0 = 1 (no power down) until selected input channel, reference mode, or power−down mode is changed, or CS is high.
Figure 9. Conversion Timing, 24 Clocks-per-Conversion, 8-Bit Bus Interface.
No DCLK delay required with dedicated serial port
15
ꢆꢠ ꢅ ꢡꢢꢣ ꢤ ꢥ
www.ti.com
SBAS417B − JUNE 2007 − REVISED JANUARY 2008
If X-Position, Y-Position, and Pressure-Touch are
measured in the single-ended mode, an external reference
voltage is needed. The TSC2046E must also be powered
from the external reference. Caution should be observed
when using the single-ended mode such that the input
voltage to the ADC does not exceed the internal reference
voltage, especially if the supply voltage is greater than
2.7V.
IOVDD
+VCC
Level
Shifter
PENIRQ
+VCC
Ω
or
90kΩ
50k
TEMP0
TEMP1
Y+
High except
when TEMP0,
TEMP1 activated.
NOTE: The differential mode can only be used for
TEMP
DIODE
X-Position,
Y-Position,
and
Pressure-Touch
X+
measurements. All other measurements require the
single-ended mode.
PD0 and PD1—Table 5 describes the power-down and
the internal reference voltage configurations. The internal
reference voltage can be turned on or off independently of
the ADC. This feature can allow extra time for the internal
reference voltage to settle to the final value prior to making
a conversion. Make sure to also allow this extra wake-up
time if the internal reference is powered down. The ADC
requires no wake-up time and can be instantaneously
used. Also note that the status of the internal reference
power-down is latched into the part (internally) with BUSY
going high. In order to turn the reference off, an additional
write to the TSC2046E is required after the channel has
been converted.
Y−
On
Y+ or X+ drivers on,
or TEMP0, TEMP1
measurements activated.
Figure 10. PENIRQ Functional Block Diagram
The −90 version of the TSC2046E uses a nominal 90kΩ
pullup resistor that allows the total resistance between the
X+ and Y− terminals to be as high as 30kΩ. Note that the
higher pullup resistance causes a slower response time of
the PENIRQ to a screen touch, so user software should
take this into account.
PD1 PD0 PENIRQ DESCRIPTION
0
0
Enabled Power-Down Between Conversions. When
each conversion is finished, the converter
enters a low-power mode. At the start of the
next conversion, the device instantly powers up
to full power. There is no need for additional
delays to ensure full operation, and the very first
conversion is valid. The Y− switch is on when in
power-down.
The PENIRQ output goes low due to the current path through
the touch screen to ground, initiating an interrupt to the
processor. During the measurement cycle for X-, Y-, and
Z-Position, the X+ input is disconnected from the PENIRQ
internal pull-up resistor. This disconnection is done to
eliminate any leakage current from the internal pull-up
resistor through the touch screen, thus causing no errors.
0
1
1
1
0
1
Disabled Reference is off and ADC is on.
Enabled Reference is on and ADC is off.
Furthermore, the PENIRQ output is disabled and low during
the measurement cycle for X-, Y-, and Z-Position. The
PENIRQ output is disabled and high during the
measurement cycle for battery monitor, auxiliary input, and
chip temperature. If the last control byte written to the
TSC2046E contains PD0 = 1, the pen-interrupt output
function is disabled and is not able to detect when the screen
is touched. In order to re-enable the pen-interrupt output
function under these circumstances, a control byte needs to
be written to the TSC2046E with PD0 = 0. If the last control
byte written to the TSC2046E contains PD0 = 0, the
pen-interrupt output function is enabled at the end of the
conversion. The end of the conversion occurs on the falling
edge of DCLK after bit 1 of the converted data is clocked out
of the TSC2046E.
Disabled Device is always powered. Reference is on and
ADC is on.
Table 5. Power-Down and Internal Reference
Selection
PENIRQ OUTPUT
The pen-interrupt output function is shown in Figure 10.
While in power-down mode with PD0 = 0, the Y-driver is on
and connects the Y-plane of the touch screen to GND. The
PENIRQ output is connected to the X+ input through two
transmission gates. When the screen is touched, the X+
input is pulled to ground through the touch screen.
In most of the TSC2046E models, the internal pullup resistor
value is nominally 50kΩ, but this value may vary between
36kΩ and 67kΩ given process and temperature variations.
In order to assure a logic low of 0.35 S (+VCC) is presented
to the PENIRQ circuitry, the total resistance between the X+
and Y− terminals must be less than 21kΩ.
It is recommended that the processor mask the interrupt that
PENIRQ is associated with whenever the processor sends
a control byte to the TSC2046E. This masking prevents false
triggering of interrupts when the PENIRQ output is disabled
in the cases discussed in this section.
16
ꢆꢠ ꢅꢡ ꢢꢣ ꢤ ꢥ
www.ti.com
SBAS417B − JUNE 2007 − REVISED JANUARY 2008
16 Clocks-per-Conversion
Digital Timing
The control bits for conversion n + 1 can be overlapped
with conversion n to allow for a conversion every 16 clock
cycles, as shown in Figure 11. This figure also shows
possible serial communication occurring with other serial
peripherals between each byte transfer from the processor
to the converter. (16 clocks cycles are possible, provided
that each conversion completes within 1.6ms of starting.
Otherwise, the signal that is captured on the input
sample-and-hold may droop enough to affect the
conversion result.) Note that the TSC2046E is fully
powered while other serial communications are taking
place during a conversion.
Figure 9, Figure 12, and Table 6 provide detailed timing for
the digital interface of the TSC2046E.
15 Clocks-per-Conversion
Figure 13 provides the fastest way to clock the
TSC2046E. This method does not work with the serial
interface of most microcontrollers and digital signal
processors, as they are generally not capable of providing
15 clock cycles per serial transfer. However, this method
can be used with field-programmable gate arrays (FPGAs)
or application- specific integrated circuits (ASICs). Note
that this effectively increases the maximum conversion
rate of the converter beyond the values given in the
specification tables, which assume 16 clock cycles per
conversion.
CS
DCLK
1
8
1
8
1
8
1
DIN
S
S
Control Bits
Control Bits
BUSY
DOUT
11 10
9
8
7
6
5
4
3
2
1
0
11 10 9
Figure 11. Conversion Timing, 16 Clocks-per-Conversion, 8-Bit Bus Interface.
No DCLK delay required with dedicated serial port
CS
tCL
tCSH
tCSS
tCH
tBD
tBD
tDO
DCLK
DIN
tDH
tDS
PD0
tBDV
tBTR
BUSY
DOUT
tDV
tTR
11
10
Figure 12. Detailed Timing Diagram
17
ꢆꢠ ꢅ ꢡꢢꢣ ꢤ ꢥ
www.ti.com
SBAS417B − JUNE 2007 − REVISED JANUARY 2008
+V
CC
S 2.7V, +V
S IOVDD S 1.5V, C
= 50pF
MAX
CC
LOAD
MIN
1.5
100
50
TYP
SYMBOL
t
DESCRIPTION
UNITS
Acquisition Time
µs
ACQ
t
DIN Valid Prior to DCLK Rising
DIN Hold After DCLK High
DCLK Falling to DOUT Valid
CS Falling to DOUT Enabled
CS Rising to DOUT Disabled
CS Falling to First DCLK Rising
CS Rising to DCLK Ignored
DCLK High
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
DS
DH
DO
t
t
200
200
200
t
DV
t
TR
t
100
10
CSS
CSH
t
t
200
200
CH
t
DCLK Low
CL
BD
t
DCLK Falling to BUSY Rising/Falling
CS Falling to BUSY Enabled
CS Rising to BUSY Disabled
200
200
200
t
t
BDV
BTR
Table 6. Timing Specifications, T = −405 C to +855 C
A
Power−Down
CS
DCLK
1
15
1
15
1
SER/
DFR
SER/
DFR
M O D E
M O DE
DIN
S
A2 A1 A0
PD1 PD0
S
A2 A1 A0
PD1 PD0
S A2 A1 A0
BUSY
DOUT
11 10
9
8
7
6
5
4
3
2
1
0
11 10
9
8
7
Figure 13. Maximum Conversion Rate, 15 Clocks-per-Conversion
Data Format
(1)
FS = Full−Scale Voltage = VREF
1LSB = VREF(1)/4096
The TSC2046E output data is in Straight Binary format, as
shown in Figure 14. This figure shows the ideal output
code for the given input voltage and does not include the
effects of offset, gain, or noise.
1LSB
11...111
11...110
11...101
8-Bit Conversion
The TSC2046E provides an 8-bit conversion mode that
can be used when faster throughput is needed and the
digital result is not as critical. By switching to the 8-bit
mode, a conversion is complete four clock cycles earlier.
Not only does this shorten each conversion by four bits
(25% faster throughput), but each conversion can actually
occur at a faster clock rate. This faster rate occurs because
the internal settling time of the TSC2046E is not as
critical—settling to better than 8 bits is all that is needed.
The clock rate can be as much as 50% faster. The faster
clock rate and fewer clock cycles combine to provide a 2x
increase in conversion rate.
00...010
00...001
00...000
−
FS 1LSB
0V
Input Voltage(2) (V)
NOTES:
− −
( REF); see Figure 2.
(1) Reference voltage at converter: +REF
−
−
(2) Input voltage at converter, after multiplexer: +IN ( IN); see
Figure 2.
Figure 14. Ideal Input Voltages and Output Codes
18
ꢆꢠ ꢅꢡ ꢢꢣ ꢤ ꢥ
www.ti.com
SBAS417B − JUNE 2007 − REVISED JANUARY 2008
Another important consideration for power dissipation is
the reference mode of the converter. In the single-ended
reference mode, the touch panel drivers are ON only when
the analog input voltage is being acquired (see Figure 9
and Table 1). The external device (for example, a resistive
touch screen), therefore, is only powered during the
acquisition period. In the differential reference mode, the
external device must be powered throughout the
acquisition and conversion periods (see Figure 9). If the
conversion rate is high, it could substantially increase
power dissipation.
POWER DISSIPATION
There are two major power modes for the TSC2046E:
full-power (PD0 = 1) and auto power-down (PD0 = 0).
When
operating
at
full
speed
and
16
clocks-per-conversion (see Figure 11), the TSC2046E
spends most of the time acquiring or converting. There is
little time for auto power-down, assuming that this mode is
active. Therefore, the difference between full-power mode
and auto power-down is negligible. If the conversion rate
is decreased by slowing the frequency of the DCLK input,
the two modes remain approximately equal. However, if
the DCLK frequency is kept at the maximum rate during a
conversion but conversions are done less often, the
difference between the two modes is dramatic.
CS also puts the TSC2046E into power-down mode.
When CS goes high, the TSC2046E immediately goes into
power-down mode and does not complete the current
conversion. The internal reference, however, does not turn
off with CS going high. To turn the reference off, an
additional write is required before CS goes high (PD1 = 0).
Figure 15 shows the difference between reducing the
DCLK frequency (scaling DCLK to match the conversion
rate) or maintaining DCLK at the highest frequency and
reducing the number of conversions per second. In the
latter case, the converter spends an increasing
percentage of time in power-down mode (assuming the
auto power-down mode is active).
When the TSC2046E first powers up, the device draws
about 20µA of current until a control byte is written to it with
PD0 = 0 to put it into power-down mode. This current draw
can be avoided if the TSC2046E is powered up with CS =
0 and DCLK = IOVDD.
1000
f
= 16 ⋅ f
SAMPLE
CLK
100
10
1
fCLK = 2MHz
Supply Current from
+VC C and IOVDD
TA = 25¡C
+VCC = 2.7V
IOVDD = 1.8V
1k
10k
100k
1M
fSAMPLE (Hz)
Figure 15. Supply Current versus Directly Scaling
the Frequency of DCLK with Sample Rate or
Maintaining DCLK at the Maximum Possible
Frequency
19
ꢆꢠ ꢅ ꢡꢢꢣ ꢤ ꢥ
www.ti.com
SBAS417B − JUNE 2007 − REVISED JANUARY 2008
The TSC2046E architecture offers no inherent rejection of
noise or voltage variation in regards to using an external
reference input. This is of particular concern when the
reference input is tied to the power supply. Any noise and
ripple from the supply appears directly in the digital results.
Whereas high-frequency noise can be filtered out, voltage
variation bacause of line frequency (50Hz or 60Hz) can be
difficult to remove.
LAYOUT
The following layout suggestions provide the most
optimum performance from the TSC2046E. Many portable
applications, however, have conflicting requirements
concerning power, cost, size, and weight. In general, most
portable devices have fairly clean power and grounds
because most of the internal components are very low
power. This situation means less bypassing for the
converter power and less concern regarding grounding.
Still, each situation is unique and the following
suggestions should be reviewed carefully.
The GND pin must be connected to a clean ground point.
In many cases, this is the analog ground. Avoid
connections which are too near the grounding point of a
microcontroller or digital signal processor. If needed, run
a ground trace directly from the converter to the
power-supply entry or battery connection point. The ideal
layout includes an analog ground plane dedicated to the
converter and associated analog circuitry.
For optimum performance, care should be taken with the
physical layout of the TSC2046E circuitry. The basic SAR
architecture is sensitive to glitches or sudden changes on
the power supply, reference, ground connections, and
digital inputs that occur just prior to latching the output of
the analog comparator. Therefore, during any single
conversion for an n-bit SAR converter, there are n windows
in which large external transient voltages can easily affect
the conversion result. Such glitches can originate from
switching power supplies, nearby digital logic, and
high-power devices. The degree of error in the digital
output depends on the reference voltage, layout, and the
exact timing of the external event. The error can change if
the external event changes in time with respect to the
DCLK input.
In the specific case of use with a resistive touch screen,
care should be taken with the connection between the
converter and the touch screen. Although resistive touch
screens have fairly low resistance, the interconnection
should be as short and robust as possible. Longer
connections are a source of error, much like the
on-resistance of the internal switches. Likewise, loose
connections can be a source of error when the contact
resistance changes with flexing or vibrations.
As indicated previously, noise can be a major source of
error in touch screen applications (such as in applications
that require a backlit LCD panel). This EMI noise can be
coupled through the LCD panel to the touch screen and
cause flickering of the converted data. Several things can
be done to reduce this error; for instance, using a touch
screen with a bottom-side metal layer connected to ground
to shunt the majority of noise to ground. Additionally,
filtering capacitors from Y+, Y–, X+, and X− pins to ground
can also help. Caution should be observed under these
circumstances for settling time of the touch screen,
especially operating in the single-ended mode and at high
data rates.
Because of the SAR architecture sensitvity, power to the
TSC2046E should be clean and well bypassed. A 0.1µF
ceramic bypass capacitor should be placed as close to the
device as possible. A 1µF to 10µF capacitor may also be
needed if the impedance of the connection between +VCC
or IOVDD and the power supplies is high. Low-leakage
capacitors should be used to minimize power dissipation
through the bypass capacitors when the TSC2046E is in
power-down mode.
A bypass capacitor is generally not needed on the VREF
pin because the internal reference is buffered by an
internal op amp. If an external reference voltage originates
from an op amp, make sure that it can drive any bypass
capacitor that is used without oscillation.
20
ꢆꢠ ꢅꢡ ꢢꢣ ꢤ ꢥ
www.ti.com
SBAS417B − JUNE 2007 − REVISED JANUARY 2008
Revision History
DATE
REV
PAGE
SECTION
Electrical Characteristics
Temperature Measurement Fixed typos in Equations (1) and (2).
Pin Configuration Added note to QFN package.
DESCRIPTION
3, 4
13
5
Fixed typos in conditions header and in Note (6).
1/08
8/07
B
A
:
NOTE Page numbers for previous revisions may differ from page numbers in the current version.
21
PACKAGE OPTION ADDENDUM
www.ti.com
15-Jan-2021
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
TSC2046EIPW
TSC2046EIPWG4
TSC2046EIPWR
TSC2046EIPWRG4
TSC2046EIRGVR
TSC2046EIRGVT
ACTIVE
TSSOP
TSSOP
TSSOP
TSSOP
VQFN
PW
16
16
16
16
16
16
90
RoHS & Green
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
-40 to 85
TSC
2046EI
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
PW
90
NIPDAU
NIPDAU
NIPDAU
NIPDAU
NIPDAU
TSC
2046EI
PW
2000 RoHS & Green
2000 RoHS & Green
2500 RoHS & Green
TSC
2046EI
PW
TSC
2046EI
RGV
RGV
TSC
2046E
VQFN
250
RoHS & Green
TSC
2046E
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
15-Jan-2021
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TSC2046E :
Automotive: TSC2046E-Q1
•
NOTE: Qualified Version Definitions:
Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects
•
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
5-Jan-2022
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TSC2046EIPWR
TSC2046EIRGVR
TSSOP
VQFN
PW
16
16
2000
2500
330.0
330.0
12.4
12.4
6.9
4.3
5.6
4.3
1.6
1.5
8.0
8.0
12.0
12.0
Q1
Q2
RGV
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
5-Jan-2022
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TSC2046EIPWR
TSC2046EIRGVR
TSSOP
VQFN
PW
16
16
2000
2500
350.0
350.0
350.0
350.0
43.0
43.0
RGV
Pack Materials-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
5-Jan-2022
TUBE
*All dimensions are nominal
Device
Package Name Package Type
Pins
SPQ
L (mm)
W (mm)
T (µm)
B (mm)
TSC2046EIPW
PW
PW
TSSOP
TSSOP
16
16
90
90
530
530
10.2
10.2
3600
3600
3.5
3.5
TSC2046EIPWG4
Pack Materials-Page 3
PACKAGE OUTLINE
PW0016A
TSSOP - 1.2 mm max height
S
C
A
L
E
2
.
5
0
0
SMALL OUTLINE PACKAGE
SEATING
PLANE
C
6.6
6.2
TYP
A
0.1 C
PIN 1 INDEX AREA
14X 0.65
16
1
2X
5.1
4.9
4.55
NOTE 3
8
9
0.30
16X
4.5
4.3
NOTE 4
1.2 MAX
0.19
B
0.1
C A B
(0.15) TYP
SEE DETAIL A
0.25
GAGE PLANE
0.15
0.05
0.75
0.50
A
20
0 -8
DETAIL A
TYPICAL
4220204/A 02/2017
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.15 mm per side.
4. This dimension does not include interlead flash. Interlead flash shall not exceed 0.25 mm per side.
5. Reference JEDEC registration MO-153.
www.ti.com
EXAMPLE BOARD LAYOUT
PW0016A
TSSOP - 1.2 mm max height
SMALL OUTLINE PACKAGE
SYMM
16X (1.5)
(R0.05) TYP
16
1
16X (0.45)
SYMM
14X (0.65)
8
9
(5.8)
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE: 10X
METAL UNDER
SOLDER MASK
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL
EXPOSED METAL
EXPOSED METAL
0.05 MAX
ALL AROUND
0.05 MIN
ALL AROUND
NON-SOLDER MASK
DEFINED
SOLDER MASK
DEFINED
15.000
(PREFERRED)
SOLDER MASK DETAILS
4220204/A 02/2017
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
PW0016A
TSSOP - 1.2 mm max height
SMALL OUTLINE PACKAGE
16X (1.5)
SYMM
(R0.05) TYP
16
1
16X (0.45)
SYMM
14X (0.65)
8
9
(5.8)
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE: 10X
4220204/A 02/2017
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
GENERIC PACKAGE VIEW
RGV 16
4 x 4, 0.65 mm pitch
VQFN - 1 mm max height
PLASTIC QUAD FLATPACK - NO LEAD
Images above are just a representation of the package family, actual package may vary.
Refer to the product data sheet for package details.
4224748/A
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2022, Texas Instruments Incorporated
相关型号:
TSC2046EIRGVTG4
SPECIALTY CONSUMER CIRCUIT, PQCC16, 4 X 4 M, 0.80 MM HEIGHT, GREEN, PLASTIC, QFN-16
TI
©2020 ICPDF网 联系我们和版权申明