TSV912A-Q1_V01 [TI]
TSV91xA-Q1 Automotive Rail-to-Rail Input/Output, 8-MHz Operational Amplifiers;型号: | TSV912A-Q1_V01 |
厂家: | TEXAS INSTRUMENTS |
描述: | TSV91xA-Q1 Automotive Rail-to-Rail Input/Output, 8-MHz Operational Amplifiers |
文件: | 总35页 (文件大小:2508K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TSV912A-Q1, TSV914A-Q1
SBOSA18A – JUNE 2020 – REVISED DECEMBER 2020
TSV91xA-Q1 Automotive Rail-to-Rail Input/Output, 8-MHz Operational Amplifiers
1 Features
3 Description
•
•
•
•
•
•
•
•
•
Rail-to-rail input and output
Low noise: 18 nV/√Hz at 1 kHz
Low power consumption: 550 µA (typical)
High-gain bandwidth: 8 MHz
Operating supply voltage from 2.5 V to 5.5 V
Low input bias current: 1 pA (typical)
Low input offset voltage: 1.5 mV (maximum)
Low offset voltage drift: ±0.5 µV/°C (typical)
ESD internal protection: ±4-kV human-body model
(HBM)
The TSV91xA-Q1 family, which includes single-,
dual-, and quad-channel operational amplifiers (op
amps), is specifically designed for general-purpose
automotive applications. Featuring rail-to-rail input
and output (RRIO) swings, wide bandwidth (8 MHz),
and low offset voltage (0.3 mV, typical), this family is
designed for a variety of applications that require a
good balance between speed and power
consumption. The op amps are unity-gain stable and
feature an ultra-low input bias current, which enables
the family to be used in applications with high-source
impedances. The low input bias current allows the
devices to be used for sensor interfaces, and active
filtering.
•
Extended temperature range: –40°C to 125°C
2 Applications
•
•
•
•
•
•
•
•
•
Optimized for AEC-Q100 grade 1 applications
Infotainment and cluster
Passive safety
The robust design of the TSV91xA-Q1 provides ease-
of-use to the circuit designer. Features include a unity-
gain stable, integrated RFI-EMI rejection filter, no
phase reversal in overdrive condition, and high
electrostatic discharge (ESD) protection (4-kV HBM).
Body electronics and lighting
HEV/EV inverter and motor control
On-board (OBC) and wireless charger
Powertrain current sensor
Advanced driver assistance systems (ADAS)
Single-supply, low-side, unidirectional current-
sensing circuit
Device Information
PACKAGE
SOT-23 (5)(2)
PART NUMBER(1)
BODY SIZE (NOM)
1.60 mm × 2.90 mm
3.91 mm × 4.90 mm
3.00 mm × 3.00 mm
8.65 mm × 3.91 mm
4.40 mm × 5.00 mm
TSV911A-Q1
SOIC (8)
TSV912A-Q1
TSV914A-Q1
VSSOP (8)(2)
SOIC (14)
TSSOP (14)
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
(2) Package is preview only for TSV91xA-Q1.
VBUS
60
50
40
30
20
ILOAD
ZLOAD
5 V
+
TSV91x
VOUT
RSHUNT
VSHUNT
0.1 ꢀ
RF
165 kꢀ
10
0
Overshoot+
Overshoot-
RG
0
50
100
150
200
250
300
3.4 kꢀ
Capacitive Load (pF)
C025
Small-Signal Overshoot vs Load Capacitance
Low-Side Motor Control
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
TSV912A-Q1, TSV914A-Q1
SBOSA18A – JUNE 2020 – REVISED DECEMBER 2020
www.ti.com
Table of Contents
1 Features............................................................................1
2 Applications.....................................................................1
3 Description.......................................................................1
4 Revision History.............................................................. 2
5 Pin Configuration and Functions...................................4
6 Specifications.................................................................. 6
6.1 Absolute Maximum Ratings........................................ 6
6.2 ESD Ratings............................................................... 6
6.3 Recommended Operating Conditions.........................6
6.4 Thermal Information: TSV912A-Q1............................ 6
6.5 Thermal Information: TSV914A-Q1............................ 7
6.6 Electrical Characteristics: VS (Total Supply
Voltage) = (V+) – (V–) = 2.5 V to 5.5 V......................... 8
6.7 Typical Characteristics..............................................10
7 Detailed Description......................................................16
7.1 Overview...................................................................16
7.2 Functional Block Diagram.........................................16
7.3 Feature Description...................................................17
7.4 Device Functional Modes..........................................17
8 Application and Implementation..................................18
8.1 Application Information............................................. 18
8.2 Typical Application.................................................... 18
9 Power Supply Recommendations................................20
9.1 Input and ESD Protection......................................... 20
10 Layout...........................................................................21
10.1 Layout Guidelines................................................... 21
10.2 Layout Example...................................................... 21
11 Device and Documentation Support..........................22
11.1 Related Links.......................................................... 22
11.2 Receiving Notification of Documentation Updates..22
11.3 Support Resources................................................. 22
11.4 Trademarks............................................................. 22
11.5 Electrostatic Discharge Caution..............................22
11.6 Glossary..................................................................22
12 Mechanical, Packaging, and Orderable
Information.................................................................... 23
4 Revision History
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision * (June 2020) to Revision A (December 2020)
Page
•
•
•
•
•
Updated the numbering format for tables, figures, and cross-references throughout the document..................1
Deleted preview tag from TSSOP package in Device Information table............................................................ 1
Deleted package preview note from TSV914-Q1 pinout drawing and Pin Functions table ............................... 4
Added note 4 to differential input voltage in Absolute Maximum Ratings table..................................................6
Added thermal information for TSSOP (14) to Thermal Information: TSV914A-Q1 table.................................. 7
Copyright © 2020 Texas Instruments Incorporated
2
Submit Document Feedback
Product Folder Links: TSV912A-Q1 TSV914A-Q1
TSV912A-Q1, TSV914A-Q1
SBOSA18A – JUNE 2020 – REVISED DECEMBER 2020
www.ti.com
Device Comparison Table
PACKAGE LEADS
NO. OF
CHANNELS
DEVICE
DBV
5
D
—
8
DGK
—
PW
—
TSV911A-Q1
1
2
4
TSV912A-Q1
TSV914A-Q1
—
8
—
—
14
—
14
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
3
Product Folder Links: TSV912A-Q1 TSV914A-Q1
TSV912A-Q1, TSV914A-Q1
SBOSA18A – JUNE 2020 – REVISED DECEMBER 2020
www.ti.com
5 Pin Configuration and Functions
OUT A
-IN A
+IN A
V-
1
2
3
4
8
7
6
5
V+
OUT B
-IN B
+IN B
Figure 5-1. TSV912A-Q1 D and DGK Package
8-Pin SOIC and VSSOP
Top View
Table 5-1. Pin Functions: TSV912A-Q1
PIN
I/O
DESCRIPTION
NAME
–IN A
+IN A
–IN B
+IN B
OUT A
OUT B
V–
NO.
2
I
I
Inverting input, channel A
Noninverting input, channel A
Inverting input, channel B
Noninverting input, channel B
Output, channel A
3
6
I
5
I
1
O
O
—
—
7
Output, channel B
4
Negative (lowest) supply or ground (for single-supply operation)
Positive (highest) supply
V+
8
Copyright © 2020 Texas Instruments Incorporated
4
Submit Document Feedback
Product Folder Links: TSV912A-Q1 TSV914A-Q1
TSV912A-Q1, TSV914A-Q1
SBOSA18A – JUNE 2020 – REVISED DECEMBER 2020
www.ti.com
OUT A
-IN A
+IN A
V+
1
2
3
4
5
6
7
14 OUT D
13 -IN D
12 +IN D
11 V-
A
D
+IN B
-IN B
OUT B
10 +IN C
9
8
-IN C
B
C
OUT C
Figure 5-2. TSV914A-Q1 D and PW Package
14-Pin SOIC and TSSOP
Top View
Table 5-2. Pin Functions: TSV914A-Q1
PIN
I/O
DESCRIPTION
NAME
–IN A
+IN A
–IN B
+IN B
–IN C
+IN C
–IN D
+IN D
OUT A
OUT B
OUT C
OUT D
V–
NO.
2
I
I
Inverting input, channel A
Noninverting input, channel A
Inverting input, channel B
Noninverting input, channel B
Inverting input, channel C
Noninverting input, channel C
Inverting input, channel D
Noninverting input, channel D
Output, channel A
3
6
I
5
I
9
I
10
13
12
1
I
I
I
O
O
O
O
—
—
7
Output, channel B
8
Output, channel C
14
11
4
Output, channel D
Negative (lowest) supply or ground (for single-supply operation)
Positive (highest) supply
V+
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
5
Product Folder Links: TSV912A-Q1 TSV914A-Q1
TSV912A-Q1, TSV914A-Q1
SBOSA18A – JUNE 2020 – REVISED DECEMBER 2020
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature (unless otherwise noted)(1)
MIN
(V–) – 0.5
–10
MAX
UNIT
Supply voltage
6
(V+) + 0.5
(V+) – (V–) + 0.2
10
V
Common-mode
Voltage(2)
V
Signal input pins
Differential(4)
Current(2)
mA
mA
°C
Output short-circuit(3)
Specified, TA
Continuous
–40
125
150
150
Junction, TJ
°C
Storage, Tstg
–65
°C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating
Conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) Input pins are diode-clamped to the power-supply rails. Current limit input signals that can swing more than 0.5 V beyond the supply
rails to 10 mA or less.
(3) Short-circuit to ground, one amplifier per package.
(4) Differential input voltages greater than 0.5 V applied continuously can result in a shift to the input offset voltage above the maximum
specification of this parameter. The magnitude of this effect increases as the ambient operating temperature rises.
6.2 ESD Ratings
over operating free-air temperature range (unless otherwise noted)
VALUE
±4000
±1500
UNIT
Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001(1)
V(ESD)
Electrostatic discharge
V
Charged-device model (CDM), per JEDEC specification JESD22-C101(2)
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
2.5
MAX
5.5
UNIT
VS
Supply voltage
V
Specified temperature
–40
125
°C
6.4 Thermal Information: TSV912A-Q1
TSV912A-Q1
THERMAL METRIC(1)
D (SOIC)
8 PINS
157.6
104.6
99.7
DGK (VSSOP)
8 PINS
TBD
UNIT
RθJA
RθJC(top)
RθJB
ψJT
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
TBD
TBD
Junction-to-top characterization parameter
Junction-to-board characterization parameter
55.6
TBD
ψJB
99.2
TBD
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
Copyright © 2020 Texas Instruments Incorporated
6
Submit Document Feedback
Product Folder Links: TSV912A-Q1 TSV914A-Q1
TSV912A-Q1, TSV914A-Q1
SBOSA18A – JUNE 2020 – REVISED DECEMBER 2020
www.ti.com
6.5 Thermal Information: TSV914A-Q1
TSV914A-Q1
THERMAL METRIC(1)
D (SOIC)
14 PINS
111.1
67.6
PW (TSSOP)
14 PINS
133.8
UNIT
RθJA
RθJC(top)
RθJB
ψJT
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
62.1
67
76.9
Junction-to-top characterization parameter
Junction-to-board characterization parameter
27.4
13.2
ψJB
66.6
76.3
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
7
Product Folder Links: TSV912A-Q1 TSV914A-Q1
TSV912A-Q1, TSV914A-Q1
SBOSA18A – JUNE 2020 – REVISED DECEMBER 2020
www.ti.com
6.6 Electrical Characteristics: VS (Total Supply Voltage) = (V+) – (V–) = 2.5 V to 5.5 V
at TA = 25°C, RL = 10 kΩ connected to VS / 2, VCM = VS / 2, and VOUT = VS / 2 (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
OFFSET VOLTAGE
VS = 5 V
VS = 5 V
±0.3
±1.5
±3
VOS
Input offset voltage
mV
TA = –40°C to 125°C
VS = 5 V
TA = –40°C to 125°C
dVOS/dT Drift
±0.5
µV/°C
PSRR
Power-supply rejection ratio
Channel separation, DC
INPUT VOLTAGE RANGE
VS = 2.5 V – 5.5 V, VCM = (V–)
At DC
±7
µV/V
dB
100
VCM
Common-mode voltage range
VS = 2.5 V to 5.5 V
(V–) – 0.1
80
(V+) + 0.1
V
VS = 5.5 V
(V–) – 0.1 V < VCM < (V+) – 1.4 V
TA = –40°C to 125°C
103
VS = 5.5 V, VCM = –0.1 V to 5.6 V
TA = –40°C to 125°C
57
75
88
70
CMRR
Common-mode rejection ratio
dB
VS = 2.5 V, (V–) – 0.1 V < VCM < (V+) – 1.4 V
TA = –40°C to 125°C
VS = 2.5 V, VCM = –0.1 V to 1.9 V
TA = –40°C to 125°C
INPUT BIAS CURRENT
IB
Input bias current
Input offset current
±5
±5
pA
pA
IOS
NOISE
En
Input voltage noise (peak-to-peak)
Input voltage noise density
Input current noise density
VS = 5 V, f = 0.1 Hz to 10 Hz
VS = 5 V, f = 10 kHz
VS = 5 V, f = 1 kHz
f = 1 kHz
4.77
12
µVPP
en
nV/√ Hz
fA/√ Hz
18
in
23
INPUT CAPACITANCE
CID
CIC
Differential
2
4
pF
pF
Common-mode
OPEN-LOOP GAIN
VS = 2.5 V, (V–) + 0.04 V < VO < (V+) – 0.04 V
RL = 10 kΩ
100
130
100
130
VS = 5.5 V, (V–) + 0.05 V < VO < (V+) – 0.05 V
RL = 10 kΩ
104
AOL
Open-loop voltage gain
dB
VS = 2.5 V, (V–) + 0.06 V < VO < (V+) – 0.06 V
RL = 2 kΩ
VS = 5.5 V, (V–) + 0.15 V < VO < (V+) – 0.15 V
RL = 2 kΩ
FREQUENCY RESPONSE
GBP
φm
Gain bandwidth product
VS = 5 V, G = 1
VS = 5 V, G = 1
8
MHz
°
Phase margin
55
VS = 5 V, G = 1
RL = 2 kΩ
SR
Slew rate
4.5
V/µs
CL = 100 pF
To 0.1%, VS = 5 V, 2-V step , G = 1
CL = 100 pF
0.5
1
tS
Settling time
µs
µs
To 0.01%, VS = 5 V, 2-V step , G = 1
CL = 100 pF
tOR
Overload recovery time
VS = 5 V, VIN × gain > VS
0.2
THD + N Total harmonic distortion + noise(1)
VS = 5 V, VO = 1 VRMS, G = 1, f = 1 kHz
0.0008%
Copyright © 2020 Texas Instruments Incorporated
8
Submit Document Feedback
Product Folder Links: TSV912A-Q1 TSV914A-Q1
TSV912A-Q1, TSV914A-Q1
SBOSA18A – JUNE 2020 – REVISED DECEMBER 2020
www.ti.com
at TA = 25°C, RL = 10 kΩ connected to VS / 2, VCM = VS / 2, and VOUT = VS / 2 (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
OUTPUT
VS = 5.5 V, RL = 10 kΩ
20
60
Voltage output swing from supply
rails
VO
mV
VS = 5.5 V, RL = 2 kΩ
VS = 5 V
ISC
ZO
Short-circuit current
±50
100
mA
Ω
Open-loop output impedance
VS = 5 V, f = 10 MHz
POWER SUPPLY
VS = 5.5 V, IO = 0 mA
550
750
IQ Quiescent current per amplifier
µA
VS = 5.5 V, IO = 0 mA TA = –40°C to 125°C
1100
(1) Third-order filter; bandwidth = 80 kHz at –3 dB.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
9
Product Folder Links: TSV912A-Q1 TSV914A-Q1
TSV912A-Q1, TSV914A-Q1
SBOSA18A – JUNE 2020 – REVISED DECEMBER 2020
www.ti.com
6.7 Typical Characteristics
at TA = 25°C, VS = 5.5 V, RL = 10 kΩ connected to VS / 2, VCM = VS / 2, and VOUT = VS / 2 (unless otherwise
noted)
35
30
25
20
15
10
5
50
40
30
20
10
0
0
Offset Voltage Drift (µV/C)
C001
C002
Offset Voltage (µV)
TA = –40°C to 125°C
Figure 6-2. Offset Voltage Drift Distribution
Figure 6-1. Offset Voltage Production Distribution
500
400
2500
2000
1500
1000
500
300
200
100
0
0
œ500
œ1000
œ1500
œ2000
œ2500
œ100
œ200
œ300
œ400
œ500
-4
-3
-2
-1
0
1
2
3
4
0
25
50
75
100
125
150
œ50
œ25
Input Common Mode Voltage (V)
Temperature (°C)
C005
C003
V+ = 2.75 V, V– = –2.75 V
Figure 6-4. Offset Voltage vs Common-Mode
Voltage
Figure 6-3. Offset Voltage vs Temperature
1000
500
0
120
100
80
60
40
20
0
210
180
150
120
90
Gain
Phase
60
500
1000
30
-20
100
0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
1k
10k 100k
Frequency (Hz)
1M
10M
Supply Voltage (V)
C004
C006
VS = 2.5 V to 5.5 V
CL = 10 pF
Figure 6-5. Offset Voltage vs Power Supply
Figure 6-6. Open-Loop Gain and Phase vs
Frequency
Copyright © 2020 Texas Instruments Incorporated
10
Submit Document Feedback
Product Folder Links: TSV912A-Q1 TSV914A-Q1
TSV912A-Q1, TSV914A-Q1
SBOSA18A – JUNE 2020 – REVISED DECEMBER 2020
www.ti.com
40
30
20
10
0
250
200
150
100
50
IBN
IBP
IOS
-10
-20
-30
0
G = +1
G = +10
G = -1
œ50
-40
1k
0
25
50
75
100
125
œ50
œ25
10k
100k
Frequency (Hz)
1M
10M
Temperature (°C)
C008
C007
Figure 6-8. Input Bias Current vs Temperature
Figure 6-7. Closed-Loop Gain vs Frequency
120
3
PSRR-
PSRR+
CMRR
2
100
80
60
40
20
0
-40°C
125°C
85°C
1
0
25°C
25°C
85°C
-40°C
œ1
œ2
œ3
125°C
10
20
30
40
50
60
Output Current (mA)
C009
1k
10k
100k
Frequency (Hz)
1M
10M
C011
V+ = 2.75 V, V– = –2.75 V
Figure 6-9. Output Voltage Swing vs Output
Current
Figure 6-10. CMRR and PSRR vs Frequency
(Referred to Input)
55
50
45
40
35
30
10
9
8
7
6
5
4
3
2
1
0
25
50
75
100
125
0
25
50
75
100
125
150
œ50
œ25
œ50
œ25
Temperature (°C)
Temperature (°C)
C012
C016
VCM = (V–) – 0.1 V to
(V+) + 0.1 V
VCM = (V–) –0.1 V to (V
+) –1.4 V
VS = 5.5 V
RL= 10 kΩ
VS = 5.5 V
RL= 10 kΩ
TA= –40°C to 125°C
TA= –40°C to 125°C
Figure 6-11. CMRR vs Temperature
Figure 6-12. CMRR vs Temperature
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
11
Product Folder Links: TSV912A-Q1 TSV914A-Q1
TSV912A-Q1, TSV914A-Q1
SBOSA18A – JUNE 2020 – REVISED DECEMBER 2020
www.ti.com
10
9
8
7
6
5
Time (1s/div)
0
25
50
75
100
125
œ50
œ25
Temperature (°C)
C014
C013
VS = 2.5 V to 5.5 V
VS = 2.5 V to 5.5 V
Figure 6-14. 0.1-Hz to 10-Hz Input Voltage Noise
Figure 6-13. PSRR vs Temperature
120
100
80
60
40
20
0
-90
-95
-100
-105
-110
-115
-120
10
100
1k
Frequency (Hz)
10k
100k
100
1k
Frequency (Hz)
10k
C015
C017
VS = 5.5 V
G = 1
VCM = 2.5 V
VOUT = 0.5 VRMS
RL = 2 kΩ
BW = 80 kHz
Figure 6-15. Input Voltage Noise Spectral Density
vs Frequency
Figure 6-16. THD + N vs Frequency
œ40
œ40
œ60
œ60
œ80
œ80
œ100
œ100
œ120
œ120
0.001
0.01
0.1
1
0.001
0.01
0.1
1
Output Voltage Amplitude (VRMS
)
Output Voltage Amplitude (VRMS
)
C018
C019
VS = 5.5 V
G = 1
VCM = 2.5 V
RL = 2 kΩ
f = 1 kHz
VS = 5.5 V
G = –1
VCM = 2.5 V
RL = 2 kΩ
f = 1 kHz
BW = 80 kHz
BW = 80 kHz
Figure 6-17. THD + N vs Amplitude
Figure 6-18. THD + N vs Amplitude
Copyright © 2020 Texas Instruments Incorporated
12
Submit Document Feedback
Product Folder Links: TSV912A-Q1 TSV914A-Q1
TSV912A-Q1, TSV914A-Q1
SBOSA18A – JUNE 2020 – REVISED DECEMBER 2020
www.ti.com
600
800
700
600
500
400
300
200
100
0
580
560
540
520
500
0
25
50
75
100
125
œ50
œ25
1.5
2
2.5
3
3.5
4
4.5
5
5.5
Temperature (°C)
C021
Supply Voltage (V)
C020
Figure 6-20. Quiescent Current vs Temperature
Figure 6-19. Quiescent Current vs Supply Voltage
200
60
50
40
30
20
160
120
80
40
0
10
0
Overshoot+
Overshoot-
0
50
100
150
200
250
300
Capacitive Load (pF)
C025
10k
100k
Frequency (Hz)
1M
10M
C024
V+ = 2.75 V
RL = 10 kΩ
V– = –2.75 V
VOUT step = 100 mVp-p
G = 1 V/V
Figure 6-22. Small-Signal Overshoot vs Load
Capacitance
Figure 6-21. Open-Loop Output Impedance vs
Frequency
60
50
40
30
20
Input
Output
10
0
Overshoot(+)
Overshoot(-)
Time (200 µs/div)
0
50
100
150
200
250
300
Capacitive Load (pF)
C026
C036
V+ = 2.75 V
G = –1 V/V
V– = –2.75 V
VOUT step = 100 mVp-p
RL = 10 kΩ
V+ = 2.75 V, V– = –2.75 V
Figure 6-24. No Phase Reversal
Figure 6-23. Small-Signal Overshoot vs Load
Capacitance
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
13
Product Folder Links: TSV912A-Q1 TSV914A-Q1
TSV912A-Q1, TSV914A-Q1
SBOSA18A – JUNE 2020 – REVISED DECEMBER 2020
www.ti.com
Input
Output
INPUT
OUTPUT
Time (1 µs/div)
Time (0.1µs/div)
C028
C030
V+ = 2.75 V, V– = –2.75 V, G = –10 V/V
V+ = 2.75 V, V– = –2.75 V, G = 1 V/V
Figure 6-25. Overload Recovery
Figure 6-26. Small-Signal Step Response
80
60
40
20
Sinking
0
Sourcing
œ20
œ40
œ60
œ80
Input
Output
Time (1 µs/div)
0
25
50
75
100
125
œ50
œ25
Temperature (°C)
C034
C031
V+ = 2.75 V
G = 1 V/V
V– = –2.75 V
CL = 100 pF
Figure 6-28. Short-Circuit Current vs Temperature
Figure 6-27. Large-Signal Step Response
0
-20
140
120
100
80
60
40
20
0
-40
-60
-80
-100
-120
-140
10M
100M
Frequency (Hz)
1G
C041
100
1k
10k 100k
Frequency (Hz)
1M
10M
C038
PRF = –10 dBm
V+ = 2.75 V, V– = –2.75 V
Figure 6-29. Electromagnetic Interference
Rejection Ratio Referred to Noninverting Input
(EMIRR+) vs Frequency
Figure 6-30. Channel Separation vs Frequency
Copyright © 2020 Texas Instruments Incorporated
14
Submit Document Feedback
Product Folder Links: TSV912A-Q1 TSV914A-Q1
TSV912A-Q1, TSV914A-Q1
SBOSA18A – JUNE 2020 – REVISED DECEMBER 2020
www.ti.com
90
200
160
120
80
75
60
45
30
15
0
40
0
0
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
0
10
20
30
40
50
60
70
80
90 100
Output Voltage (V)
Capacitive Load (pF)
C023
C037
A.
VS = 5.5 V
VS = 5.5 V
Figure 6-32. Open Loop Voltage Gain vs Output
Voltage
Figure 6-31. Phase Margin vs Capacitive Load
100
75
100
75
50
50
25
25
0
0
-25
-50
-75
-100
-125
-150
œ25
œ50
œ75
œ100
0
0.3
0.6
0.9
0
0.3
0.6
0.9
1.2
1.5
Settling time (µs)
Settling time (µs)
C032
C033
Figure 6-33. Large Signal Settling Time (Positive)
Figure 6-34. Large Signal Settling Time (Negative)
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
15
Product Folder Links: TSV912A-Q1 TSV914A-Q1
TSV912A-Q1, TSV914A-Q1
SBOSA18A – JUNE 2020 – REVISED DECEMBER 2020
www.ti.com
7 Detailed Description
7.1 Overview
The TSV91xA-Q1 series is a family of low-power, rail-to-rail input and output op amps. These devices operate
from 2.5 V to 5.5 V, are unity-gain stable, and are designed for a wide range of general-purpose automotive
applications. The input common-mode voltage range includes both rails and allows the TSV91xA-Q1 series to be
used in virtually any single-supply application. Rail-to-rail input and output swing significantly increases dynamic
range, especially in low-supply applications and are designed for driving sampling analog-to-digital converters
(ADCs).
7.2 Functional Block Diagram
V+
Reference
Current
VIN+
VINÛ
VBIAS1
Class AB
Control
Circuitry
VO
VBIAS2
VÛ
(Ground)
Copyright © 2020 Texas Instruments Incorporated
16
Submit Document Feedback
Product Folder Links: TSV912A-Q1 TSV914A-Q1
TSV912A-Q1, TSV914A-Q1
SBOSA18A – JUNE 2020 – REVISED DECEMBER 2020
www.ti.com
7.3 Feature Description
7.3.1 Rail-to-Rail Input
The input common-mode voltage range of the TSV91xA-Q1 family extends 100 mV beyond the supply rails for
the full supply voltage range of 2.5 V to 5.5 V. This performance is achieved with a complementary input stage:
an N-channel input differential pair in parallel with a P-channel differential pair, as shown in the Section 7.2. The
N-channel pair is active for input voltages close to the positive rail, typically (V+) – 1.4 V to 100 mV above the
positive supply, whereas the P-channel pair is active for inputs from 100 mV below the negative supply to
approximately (V+) – 1.4 V. There is a small transition region, typically (V+) – 1.2 V to (V+) – 1 V, in which both
pairs are on. This 200-mV transition region can vary up to 200 mV with process variation. Thus, the transition
region (with both stages on) can range from (V+) – 1.4 V to (V+) – 1.2 V on the low end, and up to (V+) – 1 V to
(V+) – 0.8 V on the high end. Within this transition region, PSRR, CMRR, offset voltage, offset drift, and THD can
degrade compared to device operation outside this region.
7.3.2 Rail-to-Rail Output
Designed as a low-power, low-voltage operational amplifier, the TSV91xA-Q1 series delivers a robust output
drive capability. A class AB output stage with common-source transistors achieves full rail-to-rail output swing
capability. For resistive loads of 10 kΩ, the output swings to within 15 mV of either supply rail, regardless of the
applied power-supply voltage. Different load conditions change the ability of the amplifier to swing close to the
rails.
7.3.3 Packages With an Exposed Thermal Pad
The TSV91xA-Q1 family is available in packages such as the WSON-8 (DSG) which feature an exposed thermal
pad. Inside the package, the die is attached to this thermal pad using an electrically conductive compound. For
this reason, when using a package with an exposed thermal pad, the thermal pad must either be connected to
V– or left floating. Attaching the thermal pad to a potential other then V– is not allowed, and the performance of
the device is not assured when doing so.
7.3.4 Overload Recovery
Overload recovery is defined as the time required for the operational amplifier output to recover from a saturated
state to a linear state. The output devices of the operational amplifier enter a saturation region when the output
voltage exceeds the rated operating voltage, because of the high input voltage or the high gain. After the device
enters the saturation region, the charge carriers in the output devices require time to return to the linear state.
After the charge carriers return to the linear state, the device begins to slew at the specified slew rate. Therefore,
the propagation delay (in case of an overload condition) is the sum of the overload recovery time and the slew
time. The overload recovery time for the TSV91xA-Q1 series is approximately 200 ns.
7.4 Device Functional Modes
The TSV91xA-Q1 family has a single functional mode. These devices are powered on as long as the power-
supply voltage is between 2.5 V (±1.25 V) and 5.5 V (±2.75 V).
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
17
Product Folder Links: TSV912A-Q1 TSV914A-Q1
TSV912A-Q1, TSV914A-Q1
SBOSA18A – JUNE 2020 – REVISED DECEMBER 2020
www.ti.com
8 Application and Implementation
Note
Information in the following applications sections is not part of the TI component specification, and TI
does not warrant its accuracy or completeness. TI’s customers are responsible for determining
suitability of components for their purposes. Customers should validate and test their design
implementation to confirm system functionality.
8.1 Application Information
The TSV91xA-Q1 series features 8-MHz bandwidth and 4.5-V/µs slew rate with only 550 µA of supply current
per channel, providing good AC performance at low power consumption. DC applications are well served with a
low input noise voltage of 18 nV / √ Hz at 1 kHz, low input bias current, and a typical input offset voltage of 0.3
mV.
8.2 Typical Application
Figure 8-1 shows the TSV91xA-Q1 configured in a low-side, motor-control application.
VBUS
ILOAD
ZLOAD
5 V
+
TSV91x
VOUT
RSHUNT
VSHUNT
0.1 ꢀ
RF
165 kꢀ
RG
3.4 kꢀ
Figure 8-1. TSV91xA-Q1 in a Low-Side, Motor-Control Application
8.2.1 Design Requirements
The design requirements for this design are:
•
•
•
Load current: 0 A to 1 A
Output voltage: 4.95 V
Maximum shunt voltage: 100 mV
Copyright © 2020 Texas Instruments Incorporated
18
Submit Document Feedback
Product Folder Links: TSV912A-Q1 TSV914A-Q1
TSV912A-Q1, TSV914A-Q1
SBOSA18A – JUNE 2020 – REVISED DECEMBER 2020
www.ti.com
8.2.2 Detailed Design Procedure
The transfer function of the circuit in Figure 8-1 is shown in Equation 1.
VOUT = ILOAD ìRSHUNT ìGain
(1)
The load current (ILOAD) produces a voltage drop across the shunt resistor (RSHUNT). The load current is set from
0 A to 1 A. To keep the shunt voltage below 100 mV at maximum load current, the largest shunt resistor is
defined using Equation 2.
VSHUNT _MAX
100mV
1A
RSHUNT
=
=
=100mW
ILOAD_MAX
(2)
Using Equation 2, RSHUNT is 100 mΩ. The voltage drop produced by ILOAD and RSHUNT is amplified by the
TSV91xA-Q1 to produce an output voltage of approximately 0 V to 4.95 V. The gain required by the TSV91xA-
Q1 to produce the necessary output voltage is calculated using Equation 3:
V
OUT _MAX - VOUT _MIN
(
)
Gain =
VIN_MAX - V
IN_MIN
(3)
Using Equation 3, the required gain is calculated to be 49.5 V/V, which is set with resistors RF and RG. Equation
4 is used to size the resistors, RF and RG, to set the gain of the TSV91xA-Q1 to 49.5 V/V.
R
(
)
F
Gain = 1+
R
G
(4)
Selecting RF as 165 kΩ and RG as 3.4 kΩ provides a combination that equals roughly 49.5 V/V. Figure 8-2
shows the measured transfer function of the circuit shown in Figure 8-1.
8.2.3 Application Curve
5
4
3
2
1
0
0
0.2
0.4
0.6
0.8
1
ILOAD (A)
C219
Figure 8-2. Low-Side, Current-Sense, Transfer Function
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
19
Product Folder Links: TSV912A-Q1 TSV914A-Q1
TSV912A-Q1, TSV914A-Q1
SBOSA18A – JUNE 2020 – REVISED DECEMBER 2020
www.ti.com
9 Power Supply Recommendations
The TSV91xA-Q1 series is specified for operation from 2.5 V to 5.5 V (±1.25 V to ±2.75 V); many specifications
apply from –40°C to 125°C. Section 6.7 presents parameters that can exhibit significant variance with regard to
operating voltage or temperature.
CAUTION
Supply voltages larger than 6 V can permanently damage the device; see the Absolute Maximum
Ratings table.
Place 0.1-µF bypass capacitors close to the power-supply pins to reduce errors coupling in from noisy or high-
impedance power supplies. For more detailed information on bypass capacitor placement, see Section 10.2.
9.1 Input and ESD Protection
The TSV91xA-Q1 series incorporates internal ESD protection circuits on all pins. For input and output pins, this
protection consists of current-steering diodes connected between the input and power-supply pins. These ESD
protection diodes provide in-circuit, input overdrive protection, as long as the current is limited to 10-mA, as
stated in the Absolute Maximum Ratings table. Figure 9-1 shows how a series input resistor is added to the
driven input to limit the input current. The added resistor contributes thermal noise at the amplifier input and the
value must be kept to a minimum in noise-sensitive applications.
V+
IOVERLOAD
10-mA maximum
VOUT
Device
VIN
5 kW
Figure 9-1. Input Current Protection
Copyright © 2020 Texas Instruments Incorporated
20
Submit Document Feedback
Product Folder Links: TSV912A-Q1 TSV914A-Q1
TSV912A-Q1, TSV914A-Q1
SBOSA18A – JUNE 2020 – REVISED DECEMBER 2020
www.ti.com
10 Layout
10.1 Layout Guidelines
For best operational performance of the device, use good printed-circuit board (PCB) layout practices, including:
•
Noise can propagate into analog circuitry through the power pins of the circuit as a whole and of op amp
itself. Bypass capacitors are used to reduce the coupled noise by providing low-impedance power sources
local to the analog circuitry.
– Connect low-ESR, 0.1-µF ceramic bypass capacitors between each supply pin and ground, placed as
close to the device as possible. A single bypass capacitor from V+ to ground is applicable for single-
supply applications.
•
•
Separate grounding for analog and digital portions of circuitry is one of the simplest and most-effective
methods of noise suppression. One or more layers on multilayer PCBs are usually devoted to ground planes.
A ground plane helps distribute heat and reduces electromagnetic interference (EMI) noise pickup. Make
sure to physically separate digital and analog grounds, paying attention to the flow of the ground current.
To reduce parasitic coupling, run the input traces as far away from the supply or output traces as possible. If
these traces cannot be kept separate, crossing the sensitive trace perpendicular is much better as opposed
to in parallel with the noisy trace.
•
•
•
Place the external components as close to the device as possible. As shown in Figure 10-2, keeping RF and
RG close to the inverting input minimizes parasitic capacitance on the inverting input.
Keep the length of input traces as short as possible. Always remember that the input traces are the most
sensitive part of the circuit.
Consider a driven, low-impedance guard ring around the critical traces. A guard ring can significantly reduce
leakage currents from nearby traces that are at different potentials.
•
•
Cleaning the PCB following board assembly is recommended for best performance.
Any precision integrated circuit can experience performance shifts resulting from moisture ingress into the
plastic package. Following any aqueous PCB cleaning process, baking the PCB assembly is recommended
to remove moisture introduced into the device packaging during the cleaning process. A low-temperature,
post-cleaning bake at 85°C for 30 minutes is sufficient for most circumstances.
10.2 Layout Example
VIN A
VIN B
+
+
VOUT A
VOUT B
RG
RG
RF
RF
Figure 10-1. Schematic Representation of Layout Example
Place components
close to device and to
each other to reduce
parasitic errors.
OUT A
Use low-ESR,
ceramic bypass
capacitor. Place as
close to the device
as possible.
VS+
GND
OUT A
V+
RF
OUT B
GND
-IN A
+IN A
Vœ
OUT B
-IN B
RF
RG
GND
VIN A
RG
+IN B
VIN B
Keep input traces short
and run the input traces
as far away from
the supply lines
Use low-ESR,
ceramic bypass
capacitor. Place as
close to the device
as possible.
GND
VSœ
Ground (GND) plane on another layer
as possible.
Figure 10-2. Layout Example
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
21
Product Folder Links: TSV912A-Q1 TSV914A-Q1
TSV912A-Q1, TSV914A-Q1
SBOSA18A – JUNE 2020 – REVISED DECEMBER 2020
www.ti.com
11 Device and Documentation Support
11.1 Related Links
The table below lists quick access links. Categories include technical documents, support and community
resources, tools and software, and quick access to order now.
Table 11-1. Related Links
TECHNICAL
DOCUMENTS
TOOLS &
SOFTWARE
SUPPORT &
COMMUNITY
PARTS
PRODUCT FOLDER
ORDER NOW
TSV912A-Q1
TSV914A-Q1
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
Click here
11.2 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. Click on
Subscribe to updates to register and receive a weekly digest of any product information that has changed. For
change details, review the revision history included in any revised document.
11.3 Support Resources
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do
not necessarily reflect TI's views; see TI's Terms of Use.
11.4 Trademarks
TI E2E™ is a trademark of Texas Instruments.
All trademarks are the property of their respective owners.
11.5 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric changes could cause the device not to meet its published
specifications.
11.6 Glossary
TI Glossary
This glossary lists and explains terms, acronyms, and definitions.
Copyright © 2020 Texas Instruments Incorporated
22
Submit Document Feedback
Product Folder Links: TSV912A-Q1 TSV914A-Q1
TSV912A-Q1, TSV914A-Q1
SBOSA18A – JUNE 2020 – REVISED DECEMBER 2020
www.ti.com
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
23
Product Folder Links: TSV912A-Q1 TSV914A-Q1
PACKAGE OPTION ADDENDUM
www.ti.com
17-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
TSV912AQDRQ1
TSV914AQDRQ1
TSV914AQPWRQ1
ACTIVE
ACTIVE
ACTIVE
SOIC
SOIC
D
D
8
2500 RoHS & Green
2500 RoHS & Green
2000 RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
-40 to 125
-40 to 125
-40 to 125
TS912Q
14
14
NIPDAU
NIPDAU
TSV914AQD
T914AQ
TSSOP
PW
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
17-Dec-2020
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
30-Dec-2020
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TSV912AQDRQ1
TSV914AQDRQ1
TSV914AQPWRQ1
SOIC
SOIC
D
D
8
2500
2500
2000
330.0
330.0
330.0
12.4
16.4
12.4
6.4
6.5
6.9
5.2
9.0
5.6
2.1
2.1
1.6
8.0
8.0
8.0
12.0
16.0
12.0
Q1
Q1
Q1
14
14
TSSOP
PW
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
30-Dec-2020
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TSV912AQDRQ1
TSV914AQDRQ1
TSV914AQPWRQ1
SOIC
SOIC
D
D
8
2500
2500
2000
853.0
853.0
853.0
449.0
449.0
449.0
35.0
35.0
35.0
14
14
TSSOP
PW
Pack Materials-Page 2
PACKAGE OUTLINE
D0008A
SOIC - 1.75 mm max height
SCALE 2.800
SMALL OUTLINE INTEGRATED CIRCUIT
C
SEATING PLANE
.228-.244 TYP
[5.80-6.19]
.004 [0.1] C
A
PIN 1 ID AREA
6X .050
[1.27]
8
1
2X
.189-.197
[4.81-5.00]
NOTE 3
.150
[3.81]
4X (0 -15 )
4
5
8X .012-.020
[0.31-0.51]
B
.150-.157
[3.81-3.98]
NOTE 4
.069 MAX
[1.75]
.010 [0.25]
C A B
.005-.010 TYP
[0.13-0.25]
4X (0 -15 )
SEE DETAIL A
.010
[0.25]
.004-.010
[0.11-0.25]
0 - 8
.016-.050
[0.41-1.27]
DETAIL A
TYPICAL
(.041)
[1.04]
4214825/C 02/2019
NOTES:
1. Linear dimensions are in inches [millimeters]. Dimensions in parenthesis are for reference only. Controlling dimensions are in inches.
Dimensioning and tolerancing per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed .006 [0.15] per side.
4. This dimension does not include interlead flash.
5. Reference JEDEC registration MS-012, variation AA.
www.ti.com
EXAMPLE BOARD LAYOUT
D0008A
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
8X (.061 )
[1.55]
SYMM
SEE
DETAILS
1
8
8X (.024)
[0.6]
SYMM
(R.002 ) TYP
[0.05]
5
4
6X (.050 )
[1.27]
(.213)
[5.4]
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:8X
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
METAL
EXPOSED
METAL
EXPOSED
METAL
.0028 MAX
[0.07]
.0028 MIN
[0.07]
ALL AROUND
ALL AROUND
SOLDER MASK
DEFINED
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
4214825/C 02/2019
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
D0008A
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
8X (.061 )
[1.55]
SYMM
1
8
8X (.024)
[0.6]
SYMM
(R.002 ) TYP
[0.05]
5
4
6X (.050 )
[1.27]
(.213)
[5.4]
SOLDER PASTE EXAMPLE
BASED ON .005 INCH [0.125 MM] THICK STENCIL
SCALE:8X
4214825/C 02/2019
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2020, Texas Instruments Incorporated
相关型号:
TSV912AHYDT
DUAL OP-AMP, 3000uV OFFSET-MAX, 4.5MHz BAND WIDTH, PDSO8, ROHS COMPLIANT, SOP-8
STMICROELECTR
©2020 ICPDF网 联系我们和版权申明