UCC1895J883B [TI]
0.1A SWITCHING CONTROLLER, 1000kHz SWITCHING FREQ-MAX, CDIP8, CERAMIC, DIP-8;
| 型号： | UCC1895J883B |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 0.1A SWITCHING CONTROLLER, 1000kHz SWITCHING FREQ-MAX, CDIP8, CERAMIC, DIP-8 CD 信息通信管理 开关 |
| 文件： | 总18页 (文件大小：490K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
TXS0102
www.ti.com ....................................................................................................................................................... SCES640C–JANUARY 2007–REVISED MAY 2009
2-BIT BIDIRECTIONAL VOLTAGE-LEVEL TRANSLATOR
FOR OPEN-DRAIN AND PUSH-PULL APPLICATIONS
1
FEATURES
TYPICAL LEVEL-SHIFTER
APPLICATIONS
2
•
No Direction-Control Signal Needed
•
•
•
I2C/SMBus
UART
•
Max Data Rates
–
–
24 Mbps (Push Pull)
2 Mbps (Open Drain)
GPIO
•
•
•
Available in the Texas Instruments NanoFree™
Package
DCT OR DCU PACKAGE
(TOP VIEW)
1.65 V to 3.6 V on A port and 2.3 V to 5.5 V on
B1
1
2
3
4
8
7
6
5
B2
B port (VCCA ≤ VCCB
)
GND
VCCA
A2
VCC Isolation Feature – If Either VCC Input Is at
GND, Both Ports Are in the High-Impedance
State
VCCB
OE
A1
•
•
•
•
No Power-Supply Sequencing Required –
Either VCCA or VCCB Can Be Ramped First
Ioff Supports Partial-Power-Down Mode
Operation
YZP PACKAGE
(BOTTOM VIEW)
Latch-Up Performance Exceeds 100 mA Per
JESD 78, Class II
D1
C1
B1
A1
D2
C2
B2
A2
4 5
3 6
2 7
1 8
A2
A1
VCCA
OE
ESD Protection Exceeds JESD 22
VCCB
GND
B2
–
A Port
B1
–
–
–
2500-V Human-Body Model (A114-B)
250-V Machine Model (A115-A)
1500-V Charged-Device Model (C101)
–
B Port
–
–
–
8-kV Human-Body Model (A114-B)
250-V Machine Model (A115-A)
1500-V Charged-Device Model (C101)
DESCRIPTION/ORDERING INFORMATION
This two-bit non-inverting translator is a bidirectional voltage-level translator and can be used to establish digital
switching compatibility between mixed-voltage systems. It uses two separate configurable power-supply rails,
with the A ports supporting operating voltages from 1.65 V to 3.6 V while it tracks the VCCA supply, and the B
ports supporting operating voltages from 2.3 V to 5.5 V while it tracks the VCCB supply. This allows the support of
both lower and higher logic signal levels while providing bidirectional translation capabilities between any of the
1.8-V, 2.5-V, 3.3-V, and 5-V voltage nodes.
When the output-enable (OE) input is low, all I/Os are placed in the high-impedance state, which significantly
reduces the power-supply quiescent current consumption.
To ensure the high-impedance state during power up or power down, OE should be tied to GND through a
pulldown resistor; the minimum value of the resistor is determined by the current-sourcing capability of the driver.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
NanoFree, NanoStar are trademarks of Texas Instruments.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2007–2009, Texas Instruments Incorporated
TXS0102
SCES640C–JANUARY 2007–REVISED MAY 2009 ....................................................................................................................................................... www.ti.com
ORDERING INFORMATION
TA
PACKAGE(1)(2)
ORDERABLE PART NUMBER
TOP-SIDE MARKING(3)
2H_
NanoStar™ – WCSP (DSBGA)
0.23-mm Large Bump – YZP
Reel of 3000
TXS0102YZPR
Reel of 3000
Tube of 250
Reel of 3000
TXS0102DCTR
TXS0102DCTT
TXS0102DCUR
NFE_ _ _
NFE _ _ _
NFE_
–40°C to 85°C
SSOP – DCT
VSSOP – DCU
(1) Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
(2) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
(3) DCT: The actual top-side marking has three additional characters that designate the year, month, and wafer fab/assembly site.
DCU: The actual top-side marking has one additional character that designates the wafer fab/assembly site.
YZP: The actual top-side marking has three preceding characters to denote year, month, and sequence code, and one following
character to designate the wafer fab/assembly site. Pin 1 identifier indicates solder-bump composition (1 = SnPb, • = Pb-free).
PIN DESCRIPTION
NO.
NAME
TYPE
FUNCTION
DCT,
DCU
YZP
1
2
3
4
5
A1
B1
C1
D1
D2
B2
GND
VCCA
A2
I/O
GND
PWR
I/O
Input/output B. Referenced to VCCB
Ground
.
A-port supply voltage. 1.65 V ≤ VCCA ≤ 3.6 V and VCCA ≤ VCCB
Input/output A. Referenced to VCCA
Input/output A. Referenced to VCCA
.
.
A1
I/O
Output enable (active High). Pull OE low to place all outputs in 3-state mode.
Referenced to VCCA
6
C2
OE
Input
.
7
8
B2
A2
VCCB
B1
PWR
I/O
B-port supply voltage. 2.3 V ≤ VCCB ≤ 5.5 V
Input/output B. Referenced to VCCB
.
TYPICAL OPERATING CIRCUIT
1.8 V
3.3 V
0.1 mF
0.1 mF
1 mF
V
CCA
V
CCB
1.8 V
3.3 V
System
Controller
System
OE
A1
A2
B1
B2
Data
Data
2
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TXS0102
TXS0102
www.ti.com ....................................................................................................................................................... SCES640C–JANUARY 2007–REVISED MAY 2009
ABSOLUTE MAXIMUM RATINGS(1)
over recommended operating free-air temperature range (unless otherwise noted)
MIN
–0.5
–0.5
–0.5
–0.5
–0.5
–0.5
MAX
4.6
6.5
4.6
6.5
4.6
6.5
UNIT
V
VCCA
VCCB
Supply voltage range
Supply voltage range
V
A port
B port
A port
B port
A port
B port
VI < 0
VO < 0
VI
Input voltage range(2)
V
V
V
Voltage range applied to any output
VO
VO
in the high-impedance or power-off state(2)
–0.5 VCCA + 0.5
Voltage range applied to any output in the high or low state(2)(3)
–0.5 VCCB + 0.5
IIK
IOK
IO
Input clamp current
–50
–50
±50
mA
mA
mA
mA
Output clamp current
Continuous output current
Continuous current through VCCA, VCCB, or GND
±100
220
227
102
DCT package
DCU package
YZP package
θJA
Package thermal impedance(4)
°C/W
°C
Tstg
Storage temperature range
–65
150
(1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) The input and output negative-voltage ratings may be exceeded if the input and output current ratings are observed.
(3) The value of VCCA and VCCB are provided in the recommended operating conditions table.
(4) The package thermal impedance is calculated in accordance with JESD 51-7.
RECOMMENDED OPERATING CONDITIONS(1)(2)
VCCA
VCCB
MIN
MAX
UNIT
V
VCCA
VCCB
Supply voltage(3)
Supply voltage
1.65
3.6
2.3
VCCI – 0.2
VCCI – 0.4
VCCI – 0.4
VCCA × 0.65
0
5.5
V
1.65 V to 1.95 V
2.3 V to 3.6 V
VCCI
A-port I/Os
2.3 V to 5.5 V
2.3 V to 5.5 V
VCCI
High-level
VIH
V
V
input voltage
B-port I/Os
VCCI
1.65 V to 3.6 V
OE input
5.5
A-port I/Os
0.15
Low-level
input voltage
(4)
VIL
B-port I/Os
1.65 V to 3.6 V
2.3 V to 5.5 V
2.3 V to 5.5 V
0
0.15
OE input
0
VCCA × 0.35
A-port I/Os, push-pull driving
B-port I/Os, push-pull driving
Control input
10
10
10
85
Input transition
rise or fall rate
Δt/Δv
1.65 V to 3.6 V
ns/V
°C
TA
Operating free-air temperature
–40
(1) VCCI is the supply voltage associated with the input port.
(2) VCCO is the supply voltage associated with the output port.
(3) VCCA must be less than or equal to VCCB, and VCCA must not exceed 3.6 V.
(4) The maximum VIL value is provided to ensure that a valid VOL is maintained. The VOL value is VIL plus the voltage drop across the
pass-gate transistor.
Copyright © 2007–2009, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Link(s): TXS0102
TXS0102
SCES640C–JANUARY 2007–REVISED MAY 2009 ....................................................................................................................................................... www.ti.com
ELECTRICAL CHARACTERISTICS(1)(2)(3)
over recommended operating free-air temperature range (unless otherwise noted)
TA = 25°C
–40°C to 85°C
MIN MAX
TEST
CONDITIONS
PARAMETER
VOHA
VOLA
VOHB
VOLB
II
VCCA
VCCB
UNIT
MIN TYP MAX
IOH = –20 µA,
VIB ≥ VCCB – 0.4 V
1.65 V to 3.6 V
1.65 V to 3.6 V
1.65 V to 3.6 V
1.65 V to 3.6 V
2.3 V to 5.5 V
2.3 V to 5.5 V
2.3 V to 5.5 V
2.3 V to 5.5 V
VCCA × 0.67
V
V
V
V
IOL = 1 mA,
VIB ≤ 0.15 V
0.4
IOH = –20 µA,
VIA ≥ VCCA – 0.2 V
VCCB × 0.67
IOL = 1 mA,
VIA ≤ 0.15 V
0.4
OE
1.65 V to 3.6 V
0 V
2.3 V to 5.5 V
0 to 5.5 V
0 V
±1
±1
±1
±1
±2
±2
±2
±2
2.4
2.2
–1
12
–1
1
µA
µA
µA
µA
A port
B port
A or B port
Ioff
0 to 3.6 V
1.65 V to 3.6 V
1.65 V to VCCB
3.6 V
IOZ
2.3 V to 5.5 V
2.3 V to 5.5 V
0 V
VI = VO = open,
IO = 0
ICCA
µA
µA
0 V
5.5 V
1.65 V to VCCB
3.6 V
2.3 V to 5.5 V
0 V
VI = VO = open,
IO = 0
ICCB
0 V
5.5 V
VI = VCCI or GND,
IO = 0
ICCA + ICCB
1.65 V to VCCB
2.3 V to 5.5 V
14.4
3.5
µA
CI
OE
3.3 V
3.3 V
3.3 V
3.3 V
2.5
10
5
pF
A or B port
A port
B port
Cio
6
pF
6
7.5
(1) VCCI is the VCC associated with the input port.
(2) VCCO is the VCC associated with the output port.
(3) VCCA must be less than or equal to VCCB, and VCCA must not exceed 3.6 V.
4
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TXS0102
TXS0102
www.ti.com ....................................................................................................................................................... SCES640C–JANUARY 2007–REVISED MAY 2009
TIMING REQUIREMENTS
over recommended operating free-air temperature range, VCCA = 1.8 V ± 0.15 V (unless otherwise noted)
VCCB = 2.5 V
± 0.2 V
VCC = 3.3 V
± 0.3 V
VCC = 5 V
± 0.5 V
UNIT
MIN
MAX
MIN
MAX
MIN
MAX
Push-pull driving
Open-drain driving
Push-pull driving
Open-drain driving
21
2
22
2
24
2
Data rate
Mbps
ns
47
45
41
Pulse
duration
tw
Data inputs
500
500
500
TIMING REQUIREMENTS
over recommended operating free-air temperature range, VCCA = 2.5 V ± 0.2 V (unless otherwise noted)
VCCB = 2.5 V
± 0.2 V
VCC = 3.3 V
± 0.3 V
VCC = 5 V
± 0.5 V
UNIT
MIN
MAX
MIN
MAX
MIN
MAX
24
Push-pull driving
Open-drain driving
Push-pull driving
Open-drain driving
20
2
22
2
Data rate
Mbps
ns
2
50
45
41
Pulse
duration
tw
Data inputs
500
500
500
TIMING REQUIREMENTS
over recommended operating free-air temperature range, VCCA = 3.3 V ± 0.3 V (unless otherwise noted)
VCC = 3.3 V
± 0.3 V
VCC = 5 V
± 0.5 V
UNIT
MIN
MAX
23
MIN
MAX
24
Push-pull driving
Open-drain driving
Push-pull driving
Open-drain driving
Data rate
Mbps
ns
2
2
43
41
tw
Pulse duration
Data inputs
500
500
Copyright © 2007–2009, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Link(s): TXS0102
TXS0102
SCES640C–JANUARY 2007–REVISED MAY 2009 ....................................................................................................................................................... www.ti.com
SWITCHING CHARACTERISTICS
over recommended operating free-air temperature range, VCCA = 1.8 V ± 0.15 V (unless otherwise noted)
VCCB = 2.5 V
± 0.2 V
VCCB = 3.3 V
± 0.3 V
VCCB = 5 V
± 0.5 V
FROM
(INPUT)
TO
(OUTPUT)
PARAMETER
TEST CONDITIONS
UNIT
MIN
2.3
45
MAX
5.3
MIN
2.4
36
MAX
5.4
9.6
7.1
208
4.5
4.4
4.5
140
200
40
MIN
2.6
27
MAX
Push-pull driving
Open-drain driving
Push-pull driving
Open-drain driving
Push-pull driving
Open-drain driving
Push-pull driving
Open-drain driving
6.8
10
tPHL
tPLH
tPHL
tPLH
8.8
A
B
B
A
ns
6.8
7.5
198
4.7
4
260
4.4
1.9
45
5.3
1.1
36
1.2
27
ns
5.3
0.5
102
200
35
175
200
50
ten
OE
OE
A or B
A or B
ns
ns
tdis
Push-pull driving
Open-drain driving
Push-pull driving
Open-drain driving
Push-pull driving
Open-drain driving
Push-pull driving
Open-drain driving
3.2
38
4
9.5
2.3
30
9.3
132
9.1
106
6
2
22
2.7
10
1.7
4.2
2.8
7
7.6
95
trA
trB
tfA
A-port rise time
ns
ns
165
10.8
145
5.9
2.7
23
7.6
58
B-port rise time
A-port fall time
34
2
1.9
4.3
2.8
7.5
13.3
6.1
16.2
16.2
0.7
4.4
2.9
6.9
6.9
6.4
16.2
16.2
0.7
ns
13.8
13.8
0.7
tfB
B-port fall time
tSK(O)
Channel-to-channel skew
ns
Push-pull driving
21
2
22
2
24
2
Max data rate
Mbps
Open-drain driving
6
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TXS0102
TXS0102
www.ti.com ....................................................................................................................................................... SCES640C–JANUARY 2007–REVISED MAY 2009
SWITCHING CHARACTERISTICS
over recommended operating free-air temperature range, VCCA = 2.5 V ± 0.2 V (unless otherwise noted)
VCCB = 2.5 V
± 0.2 V
VCCB = 3.3 V
± 0.3 V
VCCB = 5 V
± 0.5 V
FROM
(INPUT)
TO
(OUTPUT)
PARAMETER
TEST CONDITIONS
UNIT
MIN
1.7
43
MAX
3.2
6.3
3.5
250
3
MIN
MAX
3.7
6
MIN
2.1
27
MAX
Push-pull driving
Open-drain driving
Push-pull driving
Open-drain driving
Push-pull driving
Open-drain driving
Push-pull driving
Open-drain driving
3.8
5.8
4.4
190
4.3
4
tPHL
tPLH
tPHL
tPLH
2
A
B
B
A
ns
4.1
206
3.6
4.2
1.6
140
200
40
36
2.6
37
1.8
44
4.7
2.5
170
200
50
1.2
27
ns
1
103
200
35
ten
OE
OE
A or B
A or B
ns
ns
tdis
Push-pull driving
Open-drain driving
Push-pull driving
Open-drain driving
Push-pull driving
Open-drain driving
Push-pull driving
Open-drain driving
2.8
34
7.4
149
8.3
151
5.7
6.9
7.8
8.8
0.7
2.6
28
6.6
121
7.2
112
5.5
6.2
6.7
9.4
0.7
1.8
24
5.6
89
trA
trB
tfA
A-port rise time
ns
ns
ns
3.2
35
2.9
24
2.4
12
6.1
64
B-port rise time
A-port fall time
1.9
4.4
2.2
5.1
1.9
4.3
2.4
5.4
1.8
4.2
2.6
5.4
5.3
5.8
6.6
10.4
0.7
tfB
B-port fall time
ns
ns
tSK(O)
Channel-to-channel skew
Push-pull driving
20
2
22
2
24
2
Max data rate
Mbps
Open-drain driving
Copyright © 2007–2009, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Link(s): TXS0102
TXS0102
SCES640C–JANUARY 2007–REVISED MAY 2009 ....................................................................................................................................................... www.ti.com
SWITCHING CHARACTERISTICS
over recommended operating free-air temperature range, VCCA = 3.3 V ± 0.3 V (unless otherwise noted)
VCCB = 3.3 V
± 0.3 V
VCCB = 5 V
± 0.5 V
FROM
(INPUT)
TO
(OUTPUT)
PARAMETER
TEST CONDITIONS
Push-pull driving
UNIT
MIN
1.3
36
1
MAX
2.4
4.2
4.2
204
2.5
124
2.5
139
200
40
MIN
1.4
28
1
MAX
3.1
4.6
4.4
165
3.3
97
tPHL
tPLH
tPHL
tPLH
Open-drain driving
Push-pull driving
Open-drain driving
Push-pull driving
Open-drain driving
Push-pull driving
Open-drain driving
A
B
B
A
ns
ns
2.6
105
200
35
3
3
ten
OE
OE
A or B
A or B
ns
ns
tdis
Push-pull driving
Open-drain driving
Push-pull driving
Open-drain driving
Push-pull driving
Open-drain driving
Push-pull driving
Open-drain driving
2.3
25
2.5
26
2
5.6
116
6.4
116
5.4
6.1
7.4
7.6
0.7
1.9
19
4.8
85
trA
trB
tfA
A-port rise time
ns
ns
ns
2.1
14
7.4
72
B-port rise time
A-port fall time
1.9
4.2
2.4
4.8
5
4.3
2.3
5
5.7
7.6
8.3
0.7
tfB
B-port fall time
ns
ns
tSK(O)
Channel-to-channel skew
Push-pull driving
23
2
24
2
Max data rate
Mbps
Open-drain driving
8
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TXS0102
TXS0102
www.ti.com ....................................................................................................................................................... SCES640C–JANUARY 2007–REVISED MAY 2009
PRINCIPLES OF OPERATION
Applications
The TXS0102 can be used to bridge the digital-switching compatibility gap between two voltage nodes to
successfully interface logic threshold levels found in electronic systems. It should be used in a point-to-point
topology for interfacing devices or systems operating at different interface voltages with one another. Its primary
target application use is for interfacing with open-drain drivers on the data I/Os such as I2C or 1-wire, where the
data is bidirectional and no control signal is available. The TXS0102 can also be used in applications where a
push-pull driver is connected to the data I/Os, but the TXB0102 might be a better option for such push-pull
applications.
Architecture
The TXS0102 architecture (see Figure 1) is an auto-direction-sensing based translator that does not require a
direction-control signal to control the direction of data flow from A to B or from B to A.
VCCA
VCCB
One-
shot
One-
shot
T1
T2
R1
10k
R2
10k
Gate Bias
A
B
N2
Figure 1. Architecture of a TXS01xx Cell
These two bidirectional channels independently determine the direction of data flow without a direction-control
signal. Each I/O pin can be automatically reconfigured as either an input or an output, which is how this
auto-direction feature is realized.
The TXS0102 is part of TI's "Switch" type voltage translator family and employs two key circuits to enable this
voltage translation:
1) An N-channel pass-gate transistor topology that ties the A-port to the B-port
and
2) Output one-shot (O.S.) edge-rate accelerator circuitry to detect and accelerate rising edges on the A or B
ports
For bidirectional voltage translation, pull-up resistors are included on the device for dc current sourcing capability.
The VGATE gate bias of the N-channel pass transistor is set at approximately one threshold voltage (VT) above
the VCC level of the low-voltage side. Data can flow in either direction without guidance from a control signal.
The O.S. rising-edge rate accelerator circuitry speeds up the output slew rate by monitoring the input edge for
transitions, helping maintain the data rate through the device. During a low-to-high signal rising edge, the O.S.
circuits turn on the PMOS transistors (T1, T2) to increase the current drive capability of the driver for
approximately 30 ns or 95% of the input edge, whichever occurs first. This edge-rate acceleration provides high
ac drive by bypassing the internal 10-kΩ pull-up resistors during the low-to-high transition to speed up the signal.
The output resistance of the driver is decreased to approximately 50 Ω to 70 Ω during this acceleration phase. To
minimize dynamic ICC and the possibility of signal contention, the user should wait for the O.S. circuit to turn-off
before applying a signal in the opposite direction. The worst-case duration is equal to the minimum pulse-width
number provided in the Timing Requirements section of this data sheet.
Copyright © 2007–2009, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Link(s): TXS0102
TXS0102
SCES640C–JANUARY 2007–REVISED MAY 2009 ....................................................................................................................................................... www.ti.com
Input Driver Requirements
The continuous dc-current "sinking" capability is determined by the external system-level open-drain (or
push-pull) drivers that are interfaced to the TXS0102 I/O pins. Since the high bandwidth of these bidirectional I/O
circuits is used to facilitate this fast change from an input to an output and an output to an input, they have a
modest dc-current "sourcing" capability of hundreds of micro-Amps, as determined by the internal 10-kΩ pullup
resistors.
The fall time (tfA, tfB) of a signal depends on the edge-rate and output impedance of the external device driving
TXS0102 data I/Os, as well as the capacitive loading on the data lines.
Similarly, the tPHL and max data rates also depend on the output impedance of the external driver. The values for
tfA, tfB, tPHL, and maximum data rates in the data sheet assume that the output impedance of the external driver is
less than 50 Ω.
Output Load Considerations
TI recommends careful PCB layout practices with short PCB trace lengths to avoid excessive capacitive loading
and to ensure that proper O.S. triggering takes place. PCB signal trace-lengths should be kept short enough
such that the round trip delay of any reflection is less than the one-shot duration. This improves signal integrity
by ensuring that any reflection sees a low impedance at the driver. The O.S. circuits have been designed to stay
on for approximately 30 ns. The maximum capacitance of the lumped load that can be driven also depends
directly on the one-shot duration. With very heavy capacitive loads, the one-shot can time-out before the signal is
driven fully to the positive rail. The O.S. duration has been set to best optimize trade-offs between dynamic ICC
,
load driving capability, and maximum bit-rate considerations. Both PCB trace length and connectors add to the
capacitance that the TXS0102 output sees, so it is recommended that this lumped-load capacitance be
considered to avoid O.S. retriggering, bus contention, output signal oscillations, or other adverse system-level
affects.
Power Up
During operation, ensure that VCCA ≤ VCCB at all times. The sequencing of each power supply will not damage
the device during the power up operation, so either power supply can be ramped up first.
Enable and Disable
The TXS0102 has an OE input that is used to disable the device by setting OE low, which places all I/Os in the
Hi-Z state. The disable time (tdis) indicates the delay between the time when OE goes low and when the outputs
are disabled (Hi-Z). The enable time (ten) indicates the amount of time the user must allow for the one-shot
circuitry to become operational after OE is taken high.
Pullup or Pulldown Resistors on I/O Lines
Each A-port I/O has an internal 10-kΩ pullup resistor to VCCA, and each B-port I/O has an internal 10-kΩ pullup
resistor to VCCB. If a smaller value of pullup resistor is required, an external resistor must be added from the I/O
to VCCA or VCCB (in parallel with the internal 10-kΩ resistors). Adding lower value pull-up resistors will effect VOL
levels, however. The internal pull-ups of the TXS0102 are disabled when the OE pin is low.
10
Submit Documentation Feedback
Copyright © 2007–2009, Texas Instruments Incorporated
Product Folder Link(s): TXS0102
TXS0102
www.ti.com ....................................................................................................................................................... SCES640C–JANUARY 2007–REVISED MAY 2009
PARAMETER MEASUREMENT INFORMATION
V
CCI
V
CCO
V
CCI
V
CCO
DUT
DUT
IN
IN
OUT
OUT
1 MW
1 MW
15 pF
15 pF
DATA RATE, PULSE DURATION, PROPAGATION DELAY,
OUTPUT RISE AND FALL TIME MEASUREMENT USING
AN OPEN-DRAIN DRIVER
DATA RATE, PULSE DURATION, PROPAGATION DELAY,
OUTPUT RISE AND FALL TIME MEASUREMENT USING
A PUSH-PULL DRIVER
2 × V
CCO
S1
50 kW
Open
From Output
Under Test
15 pF
50 kW
TEST
/t
S1
2 × V
t
PZL PLZ
CCO
LOAD CIRCUIT FOR ENABLE/DISABLE
TIME MEASUREMENT
t
/t
Open
PHZ PZH
t
w
V
CCI
V
CCA
V
/2
V
/2
Output
Control
(low-level
enabling)
Input
CCI
CCI
V /2
CCA
V /2
CCA
0 V
VOLTAGE WAVEFORMS
PULSE DURATION
0 V
t
PLZ
t
PZL
V
V
CCO
Output
Waveform 1
V
CCI
V
V
/2
CCO
Input
V
/2
/2
V
/2
CCI
CCI
0.1 y V
CCO
S1 at 2 × V
CCO
OL
0 V
(see Note B)
t
PHZ
t
t
t
PLH
PHL
PZH
Output
Waveform 2
S1 at GND
V
OH
0.9 y V
V
OH
CCO
0.9 y V
CCO
/2
Output
V
CCO
V
CCO
/2
CCO
(see Note B)
0.1 y V
CCO
0 V
V
OL
t
f
t
r
VOLTAGE WAVEFORMS
PROPAGATION DELAY TIMES
VOLTAGE WAVEFORMS
ENABLE AND DISABLE TIMES
A.
C
L
includes probe and jig capacitance.
B. Waveform 1 is for an output with internal conditions such that the output is low, except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high, except when disabled by the output control.
C. All input pulses are supplied by generators having the following characteristics: PRRv10 MHz, Z = 50 Ω, dv/dt ≥ 1 V/ns.
O
D. The outputs are measured one at a time, with one transition per measurement.
E.
F.
G.
H.
I.
t
t
t
V
V
and t
and t
and t
are the same as t
.
dis
.
PLZ
PZL
PLH
PHZ
are the same as t
PZH
en
are the same as t .
pd
PHL
is the V associated with the input port.
CC
CCI
is the V associated with the output port.
CCO
CC
J. All parameters and waveforms are not applicable to all devices.
Figure 2. Load Circuit and Voltage Waveforms
Copyright © 2007–2009, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Link(s): TXS0102
PACKAGE OPTION ADDENDUM
www.ti.com
6-Jan-2010
PACKAGING INFORMATION
Orderable Device
TXS0102DCTR
TXS0102DCTRE4
TXS0102DCTT
Status (1)
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
Drawing
SM8
DCT
8
8
8
8
8
8
8
8
8
8
3000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
SM8
SM8
SM8
SM8
US8
DCT
DCT
DCT
DCT
DCU
DCU
DCU
DCU
YZP
3000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
250 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
TXS0102DCTTE4
TXS0102DCTTG4
TXS0102DCUR
TXS0102DCURG4
TXS0102DCUT
TXS0102DCUTG4
TXS0102YZPR
250 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
250 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
3000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
US8
3000 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
US8
250 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
US8
250 Green (RoHS & CU NIPDAU Level-1-260C-UNLIM
no Sb/Br)
DSBGA
3000 Green (RoHS &
no Sb/Br)
SNAGCU
Level-1-260C-UNLIM
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
6-Jan-2010
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TXS0102DCUR
TXS0102YZPR
US8
DCU
YZP
8
8
3000
3000
180.0
180.0
9.2
8.4
2.25
1.02
3.35
2.02
1.05
0.63
4.0
4.0
8.0
8.0
Q3
Q1
DSBGA
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
6-Jan-2010
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TXS0102DCUR
TXS0102YZPR
US8
DCU
YZP
8
8
3000
3000
202.0
220.0
201.0
220.0
28.0
34.0
DSBGA
Pack Materials-Page 2
MECHANICAL DATA
MPDS049B – MAY 1999 – REVISED OCTOBER 2002
DCT (R-PDSO-G8)
PLASTIC SMALL-OUTLINE PACKAGE
0,30
0,15
M
0,13
0,65
8
5
0,15 NOM
2,90
2,70
4,25
3,75
Gage Plane
PIN 1
INDEX AREA
0,25
1
4
0° – 8°
0,60
0,20
3,15
2,75
1,30 MAX
Seating Plane
0,10
0,10
0,00
4188781/C 09/02
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Body dimensions do not include mold flash or protrusion
D. Falls within JEDEC MO-187 variation DA.
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
www.ti.com/audio
Data Converters
DLP® Products
DSP
Clocks and Timers
Interface
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
Logic
Power Mgmt
Microcontrollers
RFID
Telephony
Video & Imaging
Wireless
RF/IF and ZigBee® Solutions www.ti.com/lprf
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2009, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明