UCC283TDTR-ADJG3 [TI]
LOW-DROPOUT 3-A LINEAR REGULATOR FAMILY; 低压差3 -A线性稳压器系列
| 型号： | UCC283TDTR-ADJG3 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | LOW-DROPOUT 3-A LINEAR REGULATOR FAMILY |
| 文件： | 总22页 (文件大小：896K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
ꢀꢁ ꢁꢂ ꢃ ꢄ ꢅꢄ ꢆ ꢀꢁ ꢁꢂ ꢃꢄ ꢅ ꢇꢆ ꢀꢁꢁ ꢂ ꢃꢄ ꢅ ꢈꢉꢊ ꢆ ꢀꢁꢁ ꢄ ꢃꢄ ꢅ ꢄꢆ ꢀꢁꢁ ꢄ ꢃꢄ ꢅ ꢇꢆ ꢀꢁꢁ ꢄꢃ ꢄꢅ ꢈꢉ ꢊ
ꢋ ꢌ ꢍꢎꢉꢏꢌ ꢐꢌ ꢀꢑ ꢄ ꢎꢈ ꢋ ꢒꢓꢔ ꢈꢏ ꢏꢔ ꢕꢀꢋ ꢈꢑꢌꢏ ꢖꢈ ꢗꢒ ꢋꢘ
ꢙ
SLUS215B − OCTOBER 1998 − REVISED FEBRUARY 2004
TO−263−3 TD PACKAGE
(FRONT VIEW)
TO−263−5 TD PACKAGE
(FRONT VIEW)
D
D
D
D
Precision Positive Linear Series Pass
Voltage Regulation
5
4
3
2
1
VOUT
0.45 V Dropout at 3 A
3
2
1
VOUT
GND
VIN
ADJ
GND
CT
50 mV Dropout at 10 mA
Quiescent Current Under 650 µA
Irrespective of Load
VIN
D
Adjustable (5-Lead) Output Voltage Version
TO−220−5 T PACKAGE
(FRONT VIEW)
D
Fixed (3-Lead) Versions for 3.3-V and 5-V
Outputs
5
4
3
2
1
VOUT
ADJ
GND
CT
D
D
Logic Shutdown Capability
+
Short-Circuit Power Limit of
(3% × V × I
)
VIN
IN
SHORT
D
Low V
to V Reverse Leakage
OUT IN
D
Thermal Shutdown
TO−220−3 T PACKAGE
(FRONT VIEW)
description
VOUT
GND
VIN
3
2
The UCC283−3/−5/−ADJ family of positive linear
+
series pass voltage regulators are tailored for
low-drop-out applications where low quiescent
power is important. Fabricated with a BiCMOS
technology ideally suited for low input-to-output
differential applications, the UCC283−5 passes
3 A while requiring only 0.45 V of typical input
voltage headroom (ensured 0.6-V dropout).
1
These regulators include reverse voltage sensing that prevents current in the reverse direction. Quiescent
current is always less than 650 µA. These devices have been internally compensated in such a way that the
need for a minimum output capacitor has been eliminated.
UCC283−3 and UCC283−5 versions are in 3-lead packages and have preset outputs at 3.3 V and 5.0 V
respectively. The output voltage is regulated to 1.5% at room temperature. The UCC283−ADJ version, in a
5-lead package, regulates the output voltage programmed by an external resistor ratio.
Short-circuit current is internally limited. The device responds to a sustained overcurrent condition by turning
off after a t
time delay. The device then stays off for a period, t
, that is 32 times the t
delay. The device
ON
OFF
ON
then begins pulsing on and off at the t /(t +t
) duty cycle of 3%. This drastically reduces the power
ON ON OFF
dissipation during short-circuit and means heat sinks need only accommodate normal operation. On the
3-leaded versions of the device t
is fixed at 750 µs, on the adjustable 5-leaded versions an external capacitor
ON
sets the on time. The off time is always 32 × t . The external timing control pin, CT, on the 5-leaded versions
ON
also serves as a shutdown input when pulled low.
Internal power dissipation is further controlled with thermal overload protection circuitry. Thermal shutdown
occurs if the junction temperature exceeds 165°C. The chip remains off until the temperature has dropped 20°C.
The UCC283 series is specified for operation over the industrial range of −40°C to 85°C, and the UCC383 series
is specified from 0°C to 70°C. These devices are available in 3- and 5-pin TO−220 and TO−263 power packages.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
ꢐ
ꢐ
ꢏ
ꢌ
ꢩ
ꢉ
ꢤ
ꢀ
ꢁ
ꢢ
ꢑ
ꢣ
ꢒ
ꢝ
ꢌ
ꢛ
ꢓ
ꢜ
ꢉ
ꢈ
ꢑ
ꢈ
ꢚ
ꢛ
ꢥ
ꢜ
ꢝ
ꢣ
ꢞ
ꢟ
ꢠ
ꢠ
ꢡ
ꢡ
ꢚ
ꢚ
ꢝ
ꢝ
ꢛ
ꢛ
ꢚ
ꢢ
ꢢ
ꢦ
ꢣ
ꢤ
ꢞ
ꢞ
ꢥ
ꢥ
ꢛ
ꢡ
ꢠ
ꢟ
ꢢ
ꢢ
ꢝ
ꢜ
ꢦ
ꢑꢥ
ꢤ
ꢧ
ꢢ
ꢨ
ꢚ
ꢣ
ꢠ
ꢢ
ꢡ
ꢚ
ꢡ
ꢝ
ꢞ
ꢛ
ꢤ
ꢩ
ꢠ
ꢛ
ꢡ
ꢡ
ꢥ
ꢢ
ꢪ
Copyright 1998−2004, Texas Instruments Incorporated
ꢞ
ꢝ
ꢣ
ꢡ
ꢝ
ꢞ
ꢟ
ꢡ
ꢝ
ꢢ
ꢦ
ꢚ
ꢜ
ꢚ
ꢣ
ꢥ
ꢞ
ꢡ
ꢫ
ꢡ
ꢥ
ꢞ
ꢝ
ꢜ
ꢬ
ꢠ
ꢒ
ꢛ
ꢟ
ꢥ
ꢢ
ꢡ
ꢠ
ꢛ
ꢩ
ꢠ
ꢞ
ꢩ
ꢭ
ꢠ
ꢡ ꢥ ꢢ ꢡꢚ ꢛꢯ ꢝꢜ ꢠ ꢨꢨ ꢦꢠ ꢞ ꢠ ꢟ ꢥ ꢡ ꢥ ꢞ ꢢ ꢪ
ꢞ
ꢞ
ꢠ
ꢛ
ꢡ
ꢮ
ꢪ
ꢐ
ꢞ
ꢝ
ꢩ
ꢤ
ꢣ
ꢡ
ꢚ
ꢝ
ꢛ
ꢦ
ꢞ
ꢝ
ꢣ
ꢥ
ꢢ
ꢢ
ꢚ
ꢛ
ꢯ
ꢩ
ꢝ
ꢥ
ꢢ
ꢛ
ꢝ
ꢡ
ꢛ
ꢥ
ꢣ
ꢥ
ꢢ
ꢢ
ꢠ
ꢞ
ꢚ
ꢨ
ꢮ
ꢚ
ꢛ
ꢣ
ꢨ
ꢤ
ꢩ
ꢥ
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢁꢂ ꢃ ꢄ ꢅꢄ ꢆ ꢀ ꢁꢁ ꢂ ꢃꢄ ꢅ ꢇꢆ ꢀꢁ ꢁꢂ ꢃ ꢄ ꢅꢈꢉ ꢊ ꢆ ꢀꢁꢁ ꢄ ꢃꢄ ꢅ ꢄꢆ ꢀꢁꢁ ꢄ ꢃꢄ ꢅ ꢇꢆ ꢀꢁꢁ ꢄ ꢃꢄ ꢅ ꢈꢉꢊ
ꢋ ꢌꢍꢎꢉ ꢏ ꢌꢐꢌꢀ ꢑ ꢄ ꢎꢈ ꢋꢒ ꢓ ꢔ ꢈꢏ ꢏꢔ ꢕ ꢀꢋꢈꢑꢌ ꢏ ꢖꢈꢗ ꢒꢋꢘ
ꢙ
SLUS215B − OCTOBER 1998 − REVISED FEBRUARY 2004
(1)
AVAILABLE OPTIONS
PACKAGE DEVICES
OUTPUT VOLTAGE (V)
(2)
TO−263−3
(2)
TO−263−5
TO−220−3
TO−220−5
T
A
MIN
3.22
TYP
3.3
MAX
3.58
TD
T
UCC283TD−3
UCC283TD−5
—
—
UCC283T−3
UCC283T−5
—
—
—
4.875
5.00
ADJ
3.3
5.125
—
−40°C to 85°C
0°C to 70°C
UCC283TD−ADJ
UCC283T−ADJ
3.22
3.58
UCC383TD−3
UCC383TD−5
—
—
—
UCC383T−3
UCC383T−5
—
—
—
4.875
5.00
ADJ
5.125
UCC383TD−ADJ
UCC383T−ADJ
1. For more package and ordering information, see the Package Option Addendum located at the end of this data sheet.
2. For 50 piece reel, add KTTT (e.g., UCC283TDKTTT−3); for 500 piece reel, add TR (e.g., UCC283TDTR−3).
functional block diagram
*5 LEADED VERSION ONLY (ADJ)
VIN
VOUT
ADJ*
V
PUMP
CURRENT LIMIT
R2
4 A/ 7 A CURRENT
REFERENCE
+
+
0.65 V
R1
1.25 V
3% DUTY CYCLE
CURRENT LIMIT TIMER
SD/CT*
GND
REVERSE VOLTAGE
SENSE
R2
0
R1
OPEN
50k
UCC283−ADJ
UCC283−3
UCC283−5
UVLO
THERMAL
SHUTDOWN
82k
150k 50k
UDG−98133
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀꢁ ꢁꢂ ꢃ ꢄ ꢅꢄ ꢆ ꢀꢁ ꢁꢂ ꢃꢄ ꢅ ꢇꢆ ꢀꢁꢁ ꢂ ꢃꢄ ꢅ ꢈꢉꢊ ꢆ ꢀꢁꢁ ꢄ ꢃꢄ ꢅ ꢄꢆ ꢀꢁꢁ ꢄ ꢃꢄ ꢅ ꢇꢆ ꢀꢁꢁꢄ ꢃꢄ ꢅꢈ ꢉꢊ
ꢋ ꢌꢍꢎꢉꢏꢌ ꢐ ꢌꢀꢑ ꢄ ꢎꢈ ꢋ ꢒꢓꢔ ꢈꢏ ꢏꢔꢕ ꢀꢋ ꢈꢑꢌ ꢏ ꢖꢈ ꢗꢒ ꢋꢘ
ꢙ
SLUS215B − OCTOBER 1998 − REVISED FEBRUARY 2004
electrical characteristics T = 0°C to 70°C for the UCC383−x series, T = −40°C to 85°C for the
A
A
UCC283−x, V
= V
+ 1.5 V, I
= 10 mA, C = 10 mF, C
= 22 mF. For the UCC283−ADJ, V
VIN
VOUT
OUT
IN
OUT VIN
= 6.5 V, V
= 5.0 V, C = 750 pF, T = T unless otherwise stated
OUT
T
J
A
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
UCC283−5 Fixed 5 V, 3 A Family
T = 25°C
4.925
4.875
5
2
5.075
5.125
10
V
V
J
Output voltage
Over temperature
Line regulation
Load regulation
V
= 5.15 V to 9 V
= 10 mA to 3 A
mV
mV
V
VIN
OUT
OUT
OUT
OUT
I
I
I
I
10
0.4
0.2
50
20
= 3 A,
V
= 4.85 V
= 4.85 V
= 4.85 V
0.6
OUT
OUT
OUT
= 1.5 A,
= 10 mA,
V
V
0.45
150
10
V
Dropout voltage, V
Peak current limit
= V
− V
VOUT
DROPOUT
VIN
mV
A
V
= 0 V
4
3
7
VOUT
Overcurrent threshold
Current limit duty cycle
4
5.5
A
V
V
= 0 V
= 0 V
3%
750
400
5%
VOUT
Overcurrent time out, t
400
1400
650
µs
ON
VOUT
Quiescent current
No load
1 V < V
µA
< V
,
VIN
≤ 5.1 V, at V
VOUT
Reverse leakage current
Undervoltage lockout
30
75
3
µA
V
VOUT
VOUT
VIN where VOUT passes current
2.5
2.8
V
UCC283−3 Fixed 3.3 V, 3 A Family
T = 25°C
3.25
3.22
3.3
3.35
3.38
7
V
V
J
Output voltage
Over temperature
Line regulation voltage
Load regulation voltage
V
= 3.45 V to 9 V
= 10 mA to 3 A
= 3A,
2
7
mV
mV
V
VIN
OUT
OUT
OUT
OUT
I
I
I
I
15
VOUT = 3.15 V
VOUT = 3.15 V
VOUT = 3.15 V
0.5
0.25
50
1
= 1.5A,
0.6
150
10
V
Dropout voltage, V
Peak current limit
= V
VIN
− V
VOUT
DROPOUT
= 10mA,
mV
A
V
= 0 V
4
3
7
VOUT
Overcurrent threshold
Current limit duty cycle
4
5.5
5%
1400
650
A
V
V
= 0 V
= 0 V
3%
750
400
VOUT
Overcurrent time out, t
400
µs
ON
VOUT
Quiescent current
No load
1 V < V
µA
< V
,
VIN
≤ 3.35 V at V
VOUT
Reverse leakage current
Undervoltage lockout
30
75
3
µA
V
VOUT
VOUT
VIN where VOUT passes current
2.5
2.8
V
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢁꢂ ꢃ ꢄ ꢅꢄ ꢆ ꢀ ꢁꢁ ꢂ ꢃꢄ ꢅ ꢇꢆ ꢀꢁ ꢁꢂ ꢃ ꢄ ꢅꢈꢉ ꢊ ꢆ ꢀꢁꢁ ꢄ ꢃꢄ ꢅ ꢄꢆ ꢀꢁꢁ ꢄ ꢃꢄ ꢅ ꢇꢆ ꢀꢁꢁ ꢄ ꢃꢄ ꢅ ꢈꢉꢊ
ꢋ ꢌꢍꢎꢉ ꢏ ꢌꢐꢌꢀ ꢑ ꢄ ꢎꢈ ꢋꢒ ꢓ ꢔ ꢈꢏ ꢏꢔ ꢕ ꢀꢋꢈꢑꢌ ꢏ ꢖꢈꢗ ꢒꢋꢘ
ꢙ
SLUS215B − OCTOBER 1998 − REVISED FEBRUARY 2004
electrical characteristics T = 0°C to 70°C for the UCC383−x series, T = −40°C to 85°C for the
A
A
UCC283−x, V
= V
+ 1.5 V, I
= 10 mA, C = 10 mF, C
= 22 mF. For the UCC283−ADJ, V
VIN
VOUT
OUT
IN
OUT VIN
= 6.5 V, V
= 5.0 V, C = 750 pF, T = T unless otherwise stated
OUT
T J A
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
UCC283−ADJ Adjustable Output, 3 A Family
TJ = 25°C
Over temperature
1.23
1.25
1.27
1.28
3
V
V
Regulating voltage at ADJ pin
1.22
Line regulation voltage, at ADJ input
Load regulation voltage, at ADJ input
V
= V
+ 150 mV to 9 V
= 10 mA to 3 A
1
2
mV
mV
V
VIN
VOUT
I
5
OUT
V
V
V
V
= 4.85 V,
= 4.85 V,
= 4.85 V,
I
I
I
= 3 A
0.4
0.2
50
7
0.6
0.45
150
10
OUT
OUT
OUT
VOUT
OUT
OUT
OUT
= 1.5 A
= 10 mA
V
Dropout voltage, V
Peak current limit
= VIN − VOUT
DROPOUT
mV
A
= 0 V
4
3
Overcurrent threshold
Current limit duty cycle
4
5.5
5
A
V
V
= 0 V
= 0 V
3
%
VOUT
Overcurrent time out, t
ON
300
575
1200
µs
VOUT
1 V < V
VIN
VOUT
< V
VOUT
Reverse leakage current
30
100
µA
V
≤ 9 V, at V
VOUT
Bias current at ADJ input
Quiescent current
20
400
0.65
40
250
650
nA
µA
V
No load
At CT input
= 9 V
Shutdown threshold
Quiescent current in shutdown
UVLO
0.25
2.5
V
75
3
µA
V
VIN
VIN where VOUT passes current
2.8
†
absolute maximum ratings over operating free-air temperature (unless otherwise noted)
Input voltage
VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 V
CT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 3 V
ADJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −0.3 V to 9 V
Storage Temperature, T
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
stg
J
Junction Temperature, T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −55°C to 150°C
Lead Temperature (soldering, 10 seconds) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300°C
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀꢁ ꢁꢂ ꢃ ꢄ ꢅꢄ ꢆ ꢀꢁ ꢁꢂ ꢃꢄ ꢅ ꢇꢆ ꢀꢁꢁ ꢂ ꢃꢄ ꢅ ꢈꢉꢊ ꢆ ꢀꢁꢁ ꢄ ꢃꢄ ꢅ ꢄꢆ ꢀꢁꢁ ꢄ ꢃꢄ ꢅ ꢇꢆ ꢀꢁꢁꢄ ꢃꢄ ꢅꢈ ꢉꢊ
ꢋ ꢌꢍꢎꢉꢏꢌ ꢐ ꢌꢀꢑ ꢄ ꢎꢈ ꢋ ꢒꢓꢔ ꢈꢏ ꢏꢔꢕ ꢀꢋ ꢈꢑꢌ ꢏ ꢖꢈ ꢗꢒ ꢋꢘ
ꢙ
SLUS215B − OCTOBER 1998 − REVISED FEBRUARY 2004
pin descriptions
ADJ: Adjust pin for the UCC283−ADJ version only. Feedback pin for the linear regulator. Program the output
voltage with R1 connected from ADJ to GND and R2 connected from VOUT to ADJ. Output voltage is given
by:
(
R1
)
1.25 V R1 ) R2
V
+
OUT
CT: Short-circuit timing capacitor and shutdown input for the UCC283−ADJ version. Pulling CT below 0.25 V
turns off the regulator and places it in a low quiescent-current mode. A timing capacitor, C, from CT to GND
programs the duration of the pulsed short-circuit on-time. On-time, t , is approximately given by:
ON
t
+ 750 k C
ON
GND: Reference ground.
VIN: Input voltage, This pin must be bypassed with a low ESL/ESR 1-µF or larger capacitor to GND. VIN can
range from (VOUT + V
) to 9 V. If VIN is reduced to zero while VOUT is held high, the reverse leakage
DROPOUT
from VOUT to VIN is less than 75µA.
VOUT: Regulated output voltage. A bypass capacitor is not required at VOUT, but may be desired for good
transient response. The bypass capacitor must not exceed a maximum value in order to insure the regulator
can start.
APPLICATION INFORMATION
overview
The UCC383 family of low dropout linear (LDO) regulators provide a regulated output voltage for applications
with up to 3 A of load current. The regulators feature a low dropout voltage and short-circuit protection, making
their use ideal for demanding high-current applications requiring fault protection.
short-circuit-protection
The UCC383 provides unique short-circuit protection circuitry that reduces power dissipation during a fault.
When an overload situation is detected, the device enters a pulsed mode of operation at 3% duty cycle reducing
the heat sink requirements during a fault. The UCC383 has two current thresholds that determine its behavior
during a fault as shown in Figure 1. When the regulator current exceeds the overcurrent threshold for a period
longer than t , the UCC383 shuts off for a period (t
) which is 32 × t . During an overload, the regulator
ON
OFF
ON
actively limits the maximum current to the peak current limit value. The peak current limit is nominally 3 A
greater than the overcurrent threshold. The regulator continues in pulsed mode until the fault is cleared as
illustrated in Figure 1.
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢁꢂ ꢃ ꢄ ꢅꢄ ꢆ ꢀ ꢁꢁ ꢂ ꢃꢄ ꢅ ꢇꢆ ꢀꢁ ꢁꢂ ꢃ ꢄ ꢅꢈꢉ ꢊ ꢆ ꢀꢁꢁ ꢄ ꢃꢄ ꢅ ꢄꢆ ꢀꢁꢁ ꢄ ꢃꢄ ꢅ ꢇꢆ ꢀꢁꢁ ꢄ ꢃꢄ ꢅ ꢈꢉꢊ
ꢋ ꢌꢍꢎꢉ ꢏ ꢌꢐꢌꢀ ꢑ ꢄ ꢎꢈ ꢋꢒ ꢓ ꢔ ꢈꢏ ꢏꢔ ꢕ ꢀꢋꢈꢑꢌ ꢏ ꢖꢈꢗ ꢒꢋꢘ
ꢙ
SLUS215B − OCTOBER 1998 − REVISED FEBRUARY 2004
APPLICATION INFORMATION
PEAK
CURRENT
LIMIT
OVERLOAD
OUTPUT
CURRENT
OVER−
CURRENT
THRESHOLD
IO (NOM)
V
(NOM)
O
R
I
OLCL
OUTPUT
VOLTAGE
T
32 T
ON
T
32 T
ON
T
ON
32 T
ON
ON
ON
Figure 1. UCC383 Short-Circuit Timing
A capacitive load on the regulator’s output appears as a short-circuit during start-up. If the capacitance is too
large, the output voltage does not come into regulation during the initial t period and the UCC383 enters
ON
pulsed mode operation. The peak current limit, t
period, and load characteristics determine the maximum
ON
value of output capacitor that can be charged. For a constant current load the maximum output capacitance is
given as follows:
t
ON
+ ǒICL
Ǔ
C
* I
Farads
OUT(max)
LOAD
V
OUT
(1)
For worst case calculations, the minimum values of on time (t ) and peak current limit (I ) should be used.
ON
CL
The adjustable version allows the t
time to be adjusted with a capacitor on the CT pin:
ON
( )
+ 750, 000 C m Farad microseconds
t
ON(adj)
For a resistive load (R
(2)
) the maximum output capacitor can be estimated from:
LOAD
t
ON(sec)
Farads
C
+
OUT(max)
ȡ
ȏn
ȧ
ȣ
1
R
ȧ
LOAD
VOUT
R
1*
I
Ȣ
LOADȤ
CL
(3)
6
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀꢁ ꢁꢂ ꢃ ꢄ ꢅꢄ ꢆ ꢀꢁ ꢁꢂ ꢃꢄ ꢅ ꢇꢆ ꢀꢁꢁ ꢂ ꢃꢄ ꢅ ꢈꢉꢊ ꢆ ꢀꢁꢁ ꢄ ꢃꢄ ꢅ ꢄꢆ ꢀꢁꢁ ꢄ ꢃꢄ ꢅ ꢇꢆ ꢀꢁꢁꢄ ꢃꢄ ꢅꢈ ꢉꢊ
ꢋ ꢌꢍꢎꢉꢏꢌ ꢐ ꢌꢀꢑ ꢄ ꢎꢈ ꢋ ꢒꢓꢔ ꢈꢏ ꢏꢔꢕ ꢀꢋ ꢈꢑꢌ ꢏ ꢖꢈ ꢗꢒ ꢋꢘ
ꢙ
SLUS215B − OCTOBER 1998 − REVISED FEBRUARY 2004
APPLICATION INFORMATION
dropout performance
Referring to the Block Diagram, the dropout voltage of the UCC383 is equal to the minimum voltage drop (V
IN
to V
) across the N-channel MOSFET. The dropout voltage is dependent on operating conditions such as
OUT
load current, input and load voltages, as well as temperature. The UCC383 achieves a low Rds(on) through the
use of an internal charge-pump (V ) that drives the MOSFET gate. Figure 2 depicts typical dropout voltages
PUMP
versus load current for the 3.3-V and 5-V versions of the part, as well as the adjustable version programmed
to 3.0 V.
Figure 3 depicts the typical dropout performance of the adjustable version with various output voltages and load
currents.
Operating temperatures also affect the Rds(on) and dropout voltage of the UCC383. Figure 4 graphs the typical
dropout for the 3.3-V and 5-V versions with a 3-A load over temperature.
TYPICAL DROPOUT VOLTAGE
TYPICAL DROPOUT VOLTAGE
vs.
vs.
LOAD CURRENT
I
AND V
OUT
OUT
0.5
0.4
0.3
0.2
0.1
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
V
OUT
= 3.3 V
V
OUT
= 3 V
I
= 3 A
OUT
V
OUT
= 5 V
I
= 1.5 A
OUT
I
= 1 A
OUT
0
0
1
1.5
2
2.5
3
3
3.5
4
4.5
5
I
(A)
V
(V)
OUT
OUT
Figure 2
Figure 3
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢁꢂ ꢃ ꢄ ꢅꢄ ꢆ ꢀ ꢁꢁ ꢂ ꢃꢄ ꢅ ꢇꢆ ꢀꢁ ꢁꢂ ꢃ ꢄ ꢅꢈꢉ ꢊ ꢆ ꢀꢁꢁ ꢄ ꢃꢄ ꢅ ꢄꢆ ꢀꢁꢁ ꢄ ꢃꢄ ꢅ ꢇꢆ ꢀꢁꢁ ꢄ ꢃꢄ ꢅ ꢈꢉꢊ
ꢋ ꢌꢍꢎꢉ ꢏ ꢌꢐꢌꢀ ꢑ ꢄ ꢎꢈ ꢋꢒ ꢓ ꢔ ꢈꢏ ꢏꢔ ꢕ ꢀꢋꢈꢑꢌ ꢏ ꢖꢈꢗ ꢒꢋꢘ
ꢙ
SLUS215B − OCTOBER 1998 − REVISED FEBRUARY 2004
APPLICATION INFORMATION
voltage programming and shutdown feature for adjustable version
A typical application circuit based on the UCC383 adjustable version is shown in Figure 5. The output voltage
is externally programmed through a resistive divider at the ADJ pin.
TYPICAL DROPOUT VOLTAGE
vs.
CASE TEMPERATURE WITH A 3-A LOAD
0.6
0.5
V
= 3.3 V
OUT
0.4
0.3
0.2
V
= 5 V
OUT
−40
10
60
Temperature (5C)
Figure 4
ǒ
R2Ǔ
Volts
V
+ 1.25 1 )
OUT
R1
(4)
The maximum programmed output voltage is constrained by the 9-V absolute rating of the IC (this includes the
charge pump voltage) and its ability to enhance the N-channel MOSFET. Unless the load current is below the
3-A rating of the device, output voltages above 7 V are not recommended. The minimum output voltage can
be programmed down to 1.25 V. However, the input voltage must always be greater than the UVLO of the part.
The adjustable version includes a shutdown feature, limiting quiescent current to 40 µA typical. The UCC383
is shut down by pulling the CT pin to below 0.25 V. As shown in Figure 5, a small logic level MOSFET or BJT
transistor in parallel with the timing capacitor can be driven with a digital signal, putting the device in shutdown.
If the CT pin is not pulled low, the IC internally pulls up the pin enabling the regulator. The CT pin should not
be forced high, as this interferes with the short-circuit-protection feature. Selection of the timing capacitor is
explained in Short-Circuit-Protection.
The adjustable version can be used in applications requiring remote voltage sensing (i.e. monitoring a voltage
other than or not directly tied to the VOUT pin). This is possible since the inverting input of the error-voltage
amplifier (see Block Diagram) is brought out to the ADJ pin.
8
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀꢁ ꢁꢂ ꢃ ꢄ ꢅꢄ ꢆ ꢀꢁ ꢁꢂ ꢃꢄ ꢅ ꢇꢆ ꢀꢁꢁ ꢂ ꢃꢄ ꢅ ꢈꢉꢊ ꢆ ꢀꢁꢁ ꢄ ꢃꢄ ꢅ ꢄꢆ ꢀꢁꢁ ꢄ ꢃꢄ ꢅ ꢇꢆ ꢀꢁꢁꢄ ꢃꢄ ꢅꢈ ꢉꢊ
ꢋ ꢌꢍꢎꢉꢏꢌ ꢐ ꢌꢀꢑ ꢄ ꢎꢈ ꢋ ꢒꢓꢔ ꢈꢏ ꢏꢔꢕ ꢀꢋ ꢈꢑꢌ ꢏ ꢖꢈ ꢗꢒ ꢋꢘ
ꢙ
SLUS215B − OCTOBER 1998 − REVISED FEBRUARY 2004
APPLICATION INFORMATION
thermal design
The Package Information section of the Power Supply Control Products Data Book, Volume 3 (Literature
No. SLUD003) contains reference material for the thermal ratings of various packages. The section also
includes an excellent article Thermal Characteristics of Surface Mount Packages, that is the basis of the
following discussion.
Thermal design for the UCC383 family of linear regulators includes two modes of operation, normal and pulsed
mode. In normal operation, the linear regulator and heat sink must dissipate power equal to the maximum
forward voltage drop multiplied by the maximum load current. Assuming a constant current load, the expected
heat rise at the regulator’s junction can be calculated as follows:
°C
ǒq caǓ
) q
t
(q) + P
RISE
DISS
jc
(5)
Where theta, (θ) is thermal resistance and P
is the power dissipated. The thermal resistance of both the
DISS
TO−220 and TO−263 packages (junction to case) is 3°C per Watt. In order to prevent the regulator from going
into thermal shutdown, the case to ambient theta must keep the junction temperature below 150°C. If the LDO
is mounted on a 5-square inch pad of 1-ounce copper, for example, the thermal resistance from junction to
ambient becomes 60°C per Watt. If a lower thermal resistance is required by the application, the device heat
sinking would need to be improved.
When the UCC383 regulator is in pulsed mode due to an overload or short-circuit in the application, the
maximum average power dissipation is calculated as follows:
t
ON
+ ǒVIN
Ǔ
I
P
* V
Watts
PULSE(avg)
OUT
CL
33 t
ON
(6)
As seen in Equation 6, the average power during a fault is reduced dramatically by the duty cycle, allowing the
heat sink to be sized for normal operation. Although the peak power in the regulator during the t period can
ON
be significant, the thermal mass of the package generally keeps the junction temperature from rising unless the
period is increased to tens of milliseconds.
t
ON
ripple rejection
Even though the UCC383 family of linear regulators are not optimized for fast transient applications (Refer to
the UC182 Fast LDO Linear Regulator), they do offer significant power supply rejection at lower frequencies.
Figure 6 depicts ripple rejection performance in a typical application. The performance can be improved with
additional filtering.
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
ꢀ ꢁꢁꢂ ꢃ ꢄ ꢅꢄ ꢆ ꢀ ꢁꢁ ꢂ ꢃꢄ ꢅ ꢇꢆ ꢀꢁ ꢁꢂ ꢃ ꢄ ꢅꢈꢉ ꢊ ꢆ ꢀꢁꢁ ꢄ ꢃꢄ ꢅ ꢄꢆ ꢀꢁꢁ ꢄ ꢃꢄ ꢅ ꢇꢆ ꢀꢁꢁ ꢄ ꢃꢄ ꢅ ꢈꢉꢊ
ꢋ ꢌꢍꢎꢉ ꢏ ꢌꢐꢌꢀ ꢑ ꢄ ꢎꢈ ꢋꢒ ꢓ ꢔ ꢈꢏ ꢏꢔ ꢕ ꢀꢋꢈꢑꢌ ꢏ ꢖꢈꢗ ꢒꢋꢘ
ꢙ
SLUS215B − OCTOBER 1998 − REVISED FEBRUARY 2004
APPLICATION INFORMATION
UCC383−ADJ
VIN
VOUT
5
4
1
2
V
INPUT
10µF
10µF
R
LOAD
R2
R1
CT
ADJ
SHUTDOWN
GND
3
Figure 5. Typical Application for 5-Pin Adjustable Version
Figure 6. Ripple Rejection vs. Frequency
10
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
21-Apr-2012
PACKAGING INFORMATION
Status (1)
Eco Plan (2)
MSL Peak Temp (3)
Samples
Orderable Device
Package Type Package
Drawing
Pins
Package Qty
Lead/
Ball Finish
(Requires Login)
UCC283T-3
UCC283T-3G3
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
OBSOLETE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
TO-220
TO-220
TO-220
TO-220
TO-220
TO-220
KC
KC
3
3
3
3
5
5
5
3
3
3
3
5
5
3
3
5
5
50
50
50
50
50
50
Green (RoHS
& no Sb/Br)
CU SN
N / A for Pkg Type
N / A for Pkg Type
N / A for Pkg Type
N / A for Pkg Type
N / A for Pkg Type
N / A for Pkg Type
Call TI
Green (RoHS
& no Sb/Br)
CU SN
CU SN
CU SN
CU SN
CU SN
Call TI
CU SN
CU SN
CU SN
CU SN
CU SN
CU SN
CU SN
CU SN
CU SN
CU SN
UCC283T-5
KC
Green (RoHS
& no Sb/Br)
UCC283T-5G3
KC
Green (RoHS
& no Sb/Br)
UCC283T-ADJ
KC
Green (RoHS
& no Sb/Br)
UCC283T-ADJG3
UCC283TD-ADJ
KC
Green (RoHS
& no Sb/Br)
DDPAK/
TO-263
KTT
KTT
KTT
KTT
KTT
KTT
KTT
KTT
KTT
KTT
KTT
TBD
UCC283TDKTTT-3
UCC283TDKTTT-3G3
UCC283TDKTTT-5
UCC283TDKTTT-5G3
UCC283TDKTTT-ADJ
UCC283TDKTTT-ADJG3
UCC283TDTR-3
DDPAK/
TO-263
50
50
Green (RoHS
& no Sb/Br)
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
DDPAK/
TO-263
Green (RoHS
& no Sb/Br)
DDPAK/
TO-263
50
Green (RoHS
& no Sb/Br)
DDPAK/
TO-263
50
Green (RoHS
& no Sb/Br)
DDPAK/
TO-263
50
Green (RoHS
& no Sb/Br)
DDPAK/
TO-263
50
Green (RoHS
& no Sb/Br)
DDPAK/
TO-263
500
500
500
500
Green (RoHS
& no Sb/Br)
UCC283TDTR-3G3
UCC283TDTR-ADJ
UCC283TDTR-ADJG3
DDPAK/
TO-263
Green (RoHS
& no Sb/Br)
DDPAK/
TO-263
Green (RoHS
& no Sb/Br)
DDPAK/
TO-263
Green (RoHS
& no Sb/Br)
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
21-Apr-2012
Status (1)
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
OBSOLETE
OBSOLETE
OBSOLETE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
Eco Plan (2)
MSL Peak Temp (3)
Samples
Orderable Device
Package Type Package
Drawing
Pins
Package Qty
Lead/
Ball Finish
(Requires Login)
UCC383T-3
UCC383T-3G3
TO-220
TO-220
TO-220
TO-220
TO-220
TO-220
KC
KC
3
3
3
3
5
5
3
3
5
3
3
3
3
5
5
3
3
3
50
50
50
50
50
50
Green (RoHS
& no Sb/Br)
CU SN
N / A for Pkg Type
N / A for Pkg Type
N / A for Pkg Type
N / A for Pkg Type
N / A for Pkg Type
N / A for Pkg Type
Call TI
Green (RoHS
& no Sb/Br)
CU SN
CU SN
CU SN
CU SN
CU SN
Call TI
Call TI
Call TI
CU SN
CU SN
CU SN
CU SN
CU SN
CU SN
CU SN
CU SN
CU SN
UCC383T-5
KC
Green (RoHS
& no Sb/Br)
UCC383T-5G3
KC
Green (RoHS
& no Sb/Br)
UCC383T-ADJ
KC
Green (RoHS
& no Sb/Br)
UCC383T-ADJG3
UCC383TD-3
KC
Green (RoHS
& no Sb/Br)
DDPAK/
TO-263
KTT
KTT
KTT
KTT
KTT
KTT
KTT
KTT
KTT
KTT
KTT
KTT
TBD
TBD
TBD
UCC383TD-5
DDPAK/
TO-263
Call TI
UCC383TD-ADJ
UCC383TDKTTT-3
UCC383TDKTTT-3G3
UCC383TDKTTT-5
UCC383TDKTTT-5G3
UCC383TDKTTT-ADJ
UCC383TDKTTT-ADJG3
UCC383TDTR-3
UCC383TDTR-3G3
UCC383TDTR-5
DDPAK/
TO-263
Call TI
DDPAK/
TO-263
50
50
Green (RoHS
& no Sb/Br)
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
DDPAK/
TO-263
Green (RoHS
& no Sb/Br)
DDPAK/
TO-263
50
Green (RoHS
& no Sb/Br)
DDPAK/
TO-263
50
Green (RoHS
& no Sb/Br)
DDPAK/
TO-263
50
Green (RoHS
& no Sb/Br)
DDPAK/
TO-263
50
Green (RoHS
& no Sb/Br)
DDPAK/
TO-263
500
500
500
Green (RoHS
& no Sb/Br)
DDPAK/
TO-263
Green (RoHS
& no Sb/Br)
DDPAK/
TO-263
Green (RoHS
& no Sb/Br)
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
21-Apr-2012
Status (1)
ACTIVE
ACTIVE
ACTIVE
Eco Plan (2)
MSL Peak Temp (3)
Samples
Orderable Device
Package Type Package
Drawing
Pins
Package Qty
Lead/
Ball Finish
(Requires Login)
UCC383TDTR-5G3
UCC383TDTR-ADJ
UCC383TDTR-ADJG3
DDPAK/
TO-263
KTT
KTT
KTT
3
5
5
500
500
500
Green (RoHS
& no Sb/Br)
CU SN
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
DDPAK/
TO-263
Green (RoHS
& no Sb/Br)
CU SN
CU SN
DDPAK/
TO-263
Green (RoHS
& no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 3
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
UCC283TDKTTT-3
UCC283TDKTTT-5
UCC283TDKTTT-ADJ
UCC283TDTR-3
DDPAK/
TO-263
KTT
KTT
KTT
KTT
KTT
KTT
KTT
KTT
KTT
KTT
KTT
3
3
5
3
5
3
3
5
3
3
5
50
50
330.0
330.0
330.0
330.0
330.0
330.0
330.0
330.0
330.0
330.0
330.0
24.4
24.4
24.4
24.4
24.4
24.4
24.4
24.4
24.4
24.4
24.4
10.6
10.6
10.6
10.6
10.6
10.6
10.6
10.6
10.6
10.6
10.6
15.6
15.6
15.6
15.6
15.6
15.6
15.6
15.6
15.6
15.6
15.6
4.9
4.9
4.9
4.9
4.9
4.9
4.9
4.9
4.9
4.9
4.9
16.0
16.0
16.0
16.0
16.0
16.0
16.0
16.0
16.0
16.0
16.0
24.0
24.0
24.0
24.0
24.0
24.0
24.0
24.0
24.0
24.0
24.0
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
Q2
DDPAK/
TO-263
DDPAK/
TO-263
50
DDPAK/
TO-263
500
500
50
UCC283TDTR-ADJ
UCC383TDKTTT-3
UCC383TDKTTT-5
UCC383TDKTTT-ADJ
UCC383TDTR-3
DDPAK/
TO-263
DDPAK/
TO-263
DDPAK/
TO-263
50
DDPAK/
TO-263
50
DDPAK/
TO-263
500
500
500
UCC383TDTR-5
DDPAK/
TO-263
UCC383TDTR-ADJ
DDPAK/
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TO-263
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
UCC283TDKTTT-3
UCC283TDKTTT-5
UCC283TDKTTT-ADJ
UCC283TDTR-3
DDPAK/TO-263
DDPAK/TO-263
DDPAK/TO-263
DDPAK/TO-263
DDPAK/TO-263
DDPAK/TO-263
DDPAK/TO-263
DDPAK/TO-263
DDPAK/TO-263
DDPAK/TO-263
DDPAK/TO-263
KTT
KTT
KTT
KTT
KTT
KTT
KTT
KTT
KTT
KTT
KTT
3
3
5
3
5
3
3
5
3
3
5
50
50
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
367.0
45.0
45.0
45.0
45.0
45.0
45.0
45.0
45.0
45.0
45.0
45.0
50
500
500
50
UCC283TDTR-ADJ
UCC383TDKTTT-3
UCC383TDKTTT-5
UCC383TDKTTT-ADJ
UCC383TDTR-3
50
50
500
500
500
UCC383TDTR-5
UCC383TDTR-ADJ
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明