UCC28881DR [TI]
700V 极低静态电流离线开关 | D | 7 | -40 to 125;型号: | UCC28881DR |
厂家: | TEXAS INSTRUMENTS |
描述: | 700V 极低静态电流离线开关 | D | 7 | -40 to 125 开关 |
文件: | 总34页 (文件大小:875K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Sample &
Buy
Support &
Community
Reference
Design
Product
Folder
Tools &
Software
Technical
Documents
UCC28881
ZHCSEL3B –NOVEMBER 2015–REVISED JANUARY 2016
UCC28881 700V、225mA 低静态电流离线转换器
1 特性
3 说明
1
•
集成 14Ω、700V 功率金属氧化物半导体场效应晶
UCC28881 在单片器件中集成了控制器和 14Ω、700V
体管 (MOSFET)
功率 MOSFET。该器件还集成了高电压电流源,能够
在经整流的市电电压下直接启动和运行。UCC28881
与 UCC28880 属于同一器件系列,具备高电流处理能
力。
•
•
•
•
集成高电压电流源,用于内置器件偏置电源
集成电流感测
内部软启动
自偏置开关(直接在经整流的市电电压下启动和运
行)
该器件的静态电流较低,能够提供出色的效率。凭借
UCC28881,使用最少的外部组件即可构建降压、降压
/升压以及反激拓扑等最常用的转换器拓扑。
•
•
•
•
支持降压、降压/升压和反激拓扑结构
器件静态电流 <100μA
在负载电路短路期间提供稳定的电流保护
保护
UCC28881 集成了控制功率级启动的软启动功能,能
够最大程度地减小功率级组件所受的压力。
–
–
–
电流限制保护
过载和输出短路保护
过热保护
器件信息(1)
部件号
UCC28881
封装
SOIC (7)
封装尺寸(标称值)
5.00mm x 6.20mm
(1) 要了解所有可用封装,请见数据表末尾的可订购产品附录。
2 应用
•
AC-DC 电源
(非隔离式降压转换器,其在连续导通模式 (CCM)
和断续导通模式 (DCM) 下的
输出电流分别高达 225mA 和 150mA)
•
•
电表、家庭自动化开关模式电源 (SMPS)
支持微控制器 (MCU)、射频 (RF) 和物联网 (IoT)
的设备的偏置电源
•
家用电器、大型家用电器和发光二极管 (LED) 驱动
器
40
35
30
25
20
15
10
5
简化电路原理图
UCC28881
1
2
3
4
GND DRAIN
8
GND
FB
NC
6
5
VIN
VDD
HVIN
+
VOUT
-
2.7-W Low-Side Buck Standby Power
0
UCC28881 Power Consumption
-5
50
100
150
200
250
300
AC Input Voltage (VRMS
)
D001
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
English Data Sheet: SLUSC36
UCC28881
ZHCSEL3B –NOVEMBER 2015–REVISED JANUARY 2016
www.ti.com.cn
目录
8.3 Feature Description................................................. 10
8.4 Device Functional Modes........................................ 12
Application and Implementation ........................ 16
9.1 Application Information............................................ 16
9.2 Typical Application .................................................. 16
1
2
3
4
5
6
7
特性.......................................................................... 1
应用.......................................................................... 1
说明.......................................................................... 1
修订历史记录 ........................................................... 2
Device Comparison ............................................... 3
Pin Configuration and Functions......................... 3
Specifications......................................................... 4
7.1 Absolute Maximum Ratings ...................................... 4
7.2 ESD Ratings.............................................................. 4
7.3 Recommended Operating Conditions....................... 5
7.4 Thermal Information.................................................. 5
7.5 Electrical Characteristics........................................... 6
7.6 Switching Characteristics.......................................... 6
7.7 Typical Characteristics ............................................. 7
Detailed Description .............................................. 9
8.1 Overview ................................................................... 9
8.2 Functional Block Diagram ......................................... 9
9
10 Power Supply Recommendations ..................... 26
11 Layout................................................................... 26
11.1 Layout Guidelines ................................................ 26
11.2 Layout Example .................................................... 26
12 器件和文档支持 ..................................................... 27
12.1 器件支持 ............................................................... 27
12.2 社区资源................................................................ 27
12.3 商标....................................................................... 27
12.4 静电放电警告......................................................... 27
12.5 Glossary................................................................ 27
13 机械、封装和可订购信息....................................... 27
8
4 修订历史记录
Changes from Revision A (December 2015) to Revision B
Page
•
已更改 文档标题“UCC28881 700V、225mA 低静态电流离线开关”至“UCC28881 700V、225mA 低静态电流离线转换
器”。 ....................................................................................................................................................................................... 1
Changes from Original (November 2015) to Revision A
Page
•
已更改 销售状态“产品预览”至“量产数据”。............................................................................................................................. 1
2
Copyright © 2015–2016, Texas Instruments Incorporated
UCC28881
www.ti.com.cn
ZHCSEL3B –NOVEMBER 2015–REVISED JANUARY 2016
5 Device Comparison
Power Handling Capability with Different Topologies
MAXIMUM OUTPUT CURRENT
MAXIMUM OUTPUT POWER
for 85 ~ 265 VAC OPEN FRAME DESIGN
for 85 ~ 265 VAC OPEN FRAME DESIGN
PRODUCT
NON-ISOLATED BUCK
100 mA
FLYBACK
3 W
UCC28880
UCC28881
225 mA
4.5 W
6 Pin Configuration and Functions
D package
8-Pin SOIC
Top View
GND
GND
FB
1
8
DRAIN
2
3
4
6
5
NC
VDD
HVIN
Pin Functions
PIN
I/O
DESCRIPTION
NAME
DRAIN
FB
NO.
8
P
I
Drain pin
3
Feedback terminal
Ground
GND
GND
HVIN
NC
1
G
2
G
Ground
5
P
Supply pin
6
N/C
O
Not internally connected
VDD
4
Supply pin, supply is provided by internal LDO
Copyright © 2015–2016, Texas Instruments Incorporated
3
UCC28881
ZHCSEL3B –NOVEMBER 2015–REVISED JANUARY 2016
www.ti.com.cn
7 Specifications
7.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)
(1) (2) (3)
MIN
MAX
700
UNIT
(4)
(4)
(5)
HVIN
–0.3
V
DRAIN
Internally
clamped
700
770
V
IDRAIN
IDRAIN
FB
Positive drain current single pulse, pulse max duration 25 μs
mA
mA
V
Negative drain current
–700
–0.3
–0.3
6
6
VDD
IVDD
TJ
VDD is supplied from low impedance source
VDD is supplied from high impedance source
Junction temperature
V
400
150
260
150
µA
°C
°C
°C
Lead temperature 1.6 mm (1/16 inch) from case 10 seconds
Storage temperature range
Tstg
–65
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltages are with respect to GND. Currents are positive into, negative out of the specified terminal. These ratings apply over the
operating ambient temperature ranges unless otherwise noted.
(3) The device is not rated to withstand operating conditions when multiple parameters are at or near, absolute maximum ratings.
(4) TA = 25°C
(5) The MOSFET drain to source voltage is less than 400V
7.2 ESD Ratings
UNIT
Human Body Model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins
except HVIN pin
±2000
±1500
±500
V
V
V
(1)
(1)
V(ESD)
Electrostatic discharge
Human Body Model (HBM) per ANSI/ESDA/JEDEC JS-001, HVIN pin
Charged device model (CDM), per JEDEC specification JESD22-C101,
(2)
all pins
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
4
Copyright © 2015–2016, Texas Instruments Incorporated
UCC28881
www.ti.com.cn
ZHCSEL3B –NOVEMBER 2015–REVISED JANUARY 2016
7.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
NOM
MAX
UNIT
V
VVDD
VFB
TJ
Voltage On VDD pin
5
Voltage on FB pin
–0.2
–40
5
V
Operating junction temperature
+125
°C
7.4 Thermal Information
UCC28881
D (SOIC)
7 PINS
134.4
42.6
(1)
THERMAL METRIC
UNIT
RθJA
RθJC(top)
RθJB
ψJT
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
Junction-to-top characterization parameter
°C/W
°C/W
°C/W
°C/W
°C/W
85
6.4
ψJB
Junction-to-board characterization parameter
76
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
Copyright © 2015–2016, Texas Instruments Incorporated
5
UCC28881
ZHCSEL3B –NOVEMBER 2015–REVISED JANUARY 2016
www.ti.com.cn
7.5 Electrical Characteristics
VHVIN = 30 V, TA = TJ = –40°C to +125°C (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
VHVIN(min)
INL
Minimum Voltage to start-up
30
100
V
Internal supply current, no load FB = 1.25 V (> VFB_TH
)
58
86
µA
Internal supply current, full
FB = 0.75 V (> VFB_TH
load
IFL
)
120
µA
ICH0
ICH1
Charging VDD Cap current
Charging VDD Cap current
VVDD = 0 V,
–3.8
–1.6
–0.4
mA
mA
VVDD = 4.4V, VFB = 1.25 V
–3.40
–1.30
–0.25
Internally regulated low
Voltage supply (supplied from
HVIN pin)
VVDD
4.5
5.0
5.5
V
VFB_TH
FB pin reference threshold
VDD turn-on threshold
VDD turn-off threshold
VDD UVLO Hysteresis
Maximum Duty Cycle
0.96
3.55
3.28
0.27
45%
1.03
3.92
1.105
4.28
3.89
0.39
55%
630
V
V
V
V
VVDD(on)
VVDD(off)
ΔVVDD(uvlo)
DMAX
VDD low-to-high
VDD high-to-low
VDD high-to-low
FB = 0.75 V
3.62
0.345
Static, TA = –40°C
Static, TA = 25°C
Static, TA = 125°C
mA
mA
mA
ILIMIT
Current Limit
330
315
440
570
Thermal Shutdown
Temperature
TJ(stop)
TJ(hyst)
BV
Internal junction temperature
138.5
37.
150
45
°C
°C
V
Thermal Shutdown Hysteresis Internal junction temperature
Power MOSFET Breakdown
TJ = 25°C
700
Voltage
Power MOSFET On-
Resistance (includes internal
sense-resistor)
ID = 60 mA, TJ = 25°C
ID = 60 mA, TJ = 125°C
14
24
18
30
Ω
Ω
RDS(on)
VDRAIN = 700V, TJ = 25°C
VDRAIN = 400 V, TJ = 125°C
5
µA
µA
Power MOSFET off state
leakage current
DRAIN_ILEAKAGE
20
VHVIN = 700 V, TJ = 25°C, VVDD
5.8 V
=
4.0
6.0
7.5
6.7
36.0
µA
HVIN_IOFF
HVIN off state current
VDD clamp voltage
VHVIN = 400 V, TJ = 125°C, VVDD
5.8 V
=
20
µA
V
VVDD(clamp)
IVDD = 250 µA
7.5
7.6 Switching Characteristics
over operating free-air temperature range (unless otherwise noted)
MIN
52
TYP
62
MAX
75
UNIT
kHz
µs
fSW(max)
tON_MAX
tOFF_MIN
tMIN
Maximum switching frequency
Maximum switch on time (current limiter not triggered), FB = 0.75 V
Minimum switch off time follows every tON time, FB = 0.75 V
Minimum on time
6.5
8.3
9.7
6.5
8.3
9.7
µs
0.17
130
0.27
200
450
0.30
270
µs
tOFF(ovl)
tON_TO
Max off time (OL condition), tOFF(ovl) = tSW – tON(max)
Inductor current run away protection time threshold
µs
ns
6
Copyright © 2015–2016, Texas Instruments Incorporated
UCC28881
www.ti.com.cn
ZHCSEL3B –NOVEMBER 2015–REVISED JANUARY 2016
7.7 Typical Characteristics
1.6
1.5
1.4
1.3
1.2
1.1
1
1.2
1.15
1.1
1.05
1
0.9
0.8
0.7
0.6
0.5
0.4
0.95
0.9
0.85
0.8
50
150
250
350
450
550
650
750
-40
-20
0
20
40
60
80
100 120 140
Temperature (oC)
Drain Current Slope (mA/ms)
D002
D301
Figure 2. ILIMIT vs Drain Current Slope
Figure 1. ILIMIT vs Temperature
1.5
1.4
1.3
1.2
1.1
1
1.2
ICH0
ICH1
1.15
1.1
1.05
1
0.9
0.8
0.7
0.6
0.5
0.95
0.9
IFL
INL
0.85
-40
-20
0
20
40
60
80
100 120 140
-40
-20
0
20
40
60
80
100 120 140
Temperature (oC)
Temperature (°C)
D001
D303
Figure 4. ICH0 and ICH1 vs Temperature
Figure 3. INL and IFL vs Temperature
900
800
700
600
500
400
300
200
100
0
1.01
1.005
1
VVDD(on)
VVDD Hysteresis
0.995
0.99
0.985
0.98
IDRAIN 25oC
IDRAIN 125oC
0
5
10 15 20 25 30 35 40 45 50 55 60
Drain to Source Voltage (V)
-40
-20
0
20
40
60
80
100 120 140
Temperature (oC)
D316
D305
Figure 6. IDS vs VDS at 25°C and 125°C
Figure 5. VVDD(on) and VVDD Hysteresis vs Temperature
Copyright © 2015–2016, Texas Instruments Incorporated
7
UCC28881
ZHCSEL3B –NOVEMBER 2015–REVISED JANUARY 2016
www.ti.com.cn
Typical Characteristics (continued)
1.02
1.02
1.01
1
1.01
1
0.99
0.98
0.97
0.96
0.99
0.98
0.97
0.96
-50
0
50
100
150
-40
-20
0
20
40
60
80
100 120 140
Temperature (oC)
Temperature (°C)
D012
D308
Figure 7. Maximum Switching Frequency vs Temperature
Figure 8. VFB_TH vs Temperature
1.05
1.045
1.04
1.12
1.1
1.08
1.06
1.04
1.02
1
1.035
1.03
1.025
1.02
1.015
1.01
0.98
0.96
0.94
0.92
0.9
1.005
1
TOFF(min)
TON(max)
0.995
0.99
-40
-20
0
20
40
60
80
100 120 140
-40
-20
0
20
40
60
80
100 120 140
Temperature (°C)
D001
Temperature (oC)
D310
Figure 9. tON(max) and tOFF(min) vs Temperature
Figure 10. DRAIN breakdown voltage vs Temperature
140
136
132
128
124
120
116
112
108
104
100
0
200
400
600
800
1000
1200
1400
Copper Area (mm2)
D0201
Figure 11. RTHJA vs Copper Area
8
Copyright © 2015–2016, Texas Instruments Incorporated
UCC28881
www.ti.com.cn
ZHCSEL3B –NOVEMBER 2015–REVISED JANUARY 2016
8 Detailed Description
8.1 Overview
The UCC28881 integrates a controller and a 700-V power MOSFET into one monolithic device. The device also
integrates a high-voltage current source, enabling start up and operation directly from the rectified mains voltage.
UCC28881 is the same family device as UCC28880 and it provides higher power handling capability.
The low-quiescent current of the device enables excellent efficiency. The device is suitable for non-isolated AC-
to-DC low-side buck and buck-boost configurations with level-shifted direct feedback, but also more traditional
high-side buck, buck boost and low-power flyback converters with low standby power can be built using a
minimum number of external components.
The device generates its own internal low-voltage supply (5 V referenced to the device’s ground, GND) from the
integrated high-voltage current source. The PWM signal generation is based on a maximum constant on-time,
minimum off-time concept, with the triggering of the on-pulse depending on the feedback voltage level. Each on-
pulse is followed by a minimum off-time to ensure that the power MOSFET is not continuously driven in an on-
state. The PWM signal is AND-gated with the signal from a current limit circuit. No internal clock is required, as
the switching of the power MOSFET is load dependent. A special protection mechanism is included to avoid
runaway of the inductor current when the converter operates with the output shorted or in other abnormal
conditions that can lead to an uncontrolled increase of the inductor current. This special protection feature keeps
the MOSFET current at a safe operating level. The device is also protected from other fault conditions with
thermal shutdown, under-voltage lockout and soft-start features.
8.2 Functional Block Diagram
HVIN
5
High Voltage
Current Source
8
DRAIN
Thermal
Shutdown
Gate
VDD
4
LDO
S
R
Q
Q
UVLO
Current
Limit
Control and
Reference
Leading Edge
Blanking Time
VREF_TH = 1 V
PWM Controller
and Output Short
Circuit Protection
+
LEB
FB
3
1, 2
GND
Copyright © 2015–2016, Texas Instruments Incorporated
9
UCC28881
ZHCSEL3B –NOVEMBER 2015–REVISED JANUARY 2016
www.ti.com.cn
8.3 Feature Description
The UCC28881 integrates a 700-V rated power MOSFET switch, a PWM controller, a high-voltage current
source to supply a low-voltage power supply regulator. A bias and reference block, thermal shutdown and the
following protection features, current limiter, under voltage lockout (UVLO) and overload protection for situations
like short circuit at the output are also integrated inside UCC28881. UCC28881 is the same family device as
UCC28880 and it provides higher power handling capability.
The positive high-voltage input of the converter node (VIN+) functions as a system reference ground for the
output voltage in low-side topologies. In the low-side buck topology the output voltage is negative with respect to
the positive high-voltage input (VIN+), and in low-side buck-boost topology the output voltage is positive with
respect to the positive high-voltage input (VIN+).
In low-side buck and buck-boost topologies, the external level-shifted direct feedback circuit can be implemented
by two resistors and a high-voltage PNP transistor.
In high-side buck configuration, as well as in non-isolated flyback configuration, the output voltage is positive with
respect to the negative high-voltage input (VIN–), which is the system reference ground.
UCC28881 can operate under continuous conduction mode (CCM) or discontinuous conduction mode (DCM)
mode. CCM operation allows the converter to deliver more output power because of less current ripple. However,
it requires a higher inductor value and generally results in lower efficiency due to the added losses associated
with diode reverse recovery current. DCM mode operation uses a smaller inductor and achieves better efficiency,
but the output current handling capability is reduced because of increased current ripple. The table below shows
the current handling capability in DCM and CCM operation for the UCC28880, UCC28881 family.
Table 1. Current Handling Capability for UCC28880 and UCC28881
DEVICE
CURRENT HANDLING MODE
Discontinuous Conduction Mode (DCM)
Continuous Conduction Mode (CCM)
Discontinuous Conduction Mode (DCM)
Continuous Conduction Mode (CCM)
230 VAC ±15%
150 mA
85 V ~ 265 VAC
150 mA
UCC28881
UCC28881
UCC28880
UCC28880
225 mA
225 mA
70 mA
70 mA
100 mA
100 mA
When the bus voltage is higher than 400 V, it is recommended to limit operation to DCM mode only to avoid the
diode reverse recovery current and the associated internal MOSFET stress. Due to the higher switching loss and
device stresses at higher bus voltage, it is recommended to keep the converter input voltage less than 560 V for
the buck applications.
UCC28881 power handling capability is reduced at higher ambient temperature, as a function of the power
dissipation of the device, the device's recommended maximum operating junction temperature and the thermal
dissipation capability of the total system. De-rating of the output current according to maximum ambient
temperature can be estimated from Figure 12. The de-rating estimation assumes CCM operation, 10 µJ of
switching loss and 135°C/W RθJA and 30-kHz, full-load switching frequency. This is a conservative estimation.
The thermal handling capability can be more accurately determined through experimental measurement. For
more information on thermal evaluation methods see the IC Package and Thermal Metrics application report:
SPRA953.
10
Copyright © 2015–2016, Texas Instruments Incorporated
UCC28881
www.ti.com.cn
ZHCSEL3B –NOVEMBER 2015–REVISED JANUARY 2016
1.2
1.1
1
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
-40
-20
0
20
40
60
80
100 120 140
Ambient Temperature (oC)
D012
Figure 12. Output Current (De-Rating Factor) vs. Temperature
It is required to use fast recovery diode for the buck freewheeling diode. When designed in CCM, the diode
reverse recovery time should be less than 35 ns to keep low reverse recovery current and the switching loss. For
example, STTH1R06A provides 25-ns reverse recovery time. When designed in DCM, a slower diode can be
used, but the reverse-recovery time should be kept less than 75 ns. MURS160 can fit the requirement.
The device has a low-standby power consumption (no-load condition), only 18 mW (typical) when connected to a
230-VAC mains and 9 mW when connected to an 115-VAC mains.
The standby power does not include the power dissipated in the external feedback path, the power dissipated in
the external pre-load, the inductor in the freewheeling diode and the converter input stage (rectifiers and filter).
Copyright © 2015–2016, Texas Instruments Incorporated
11
UCC28881
ZHCSEL3B –NOVEMBER 2015–REVISED JANUARY 2016
www.ti.com.cn
8.4 Device Functional Modes
8.4.1 Start-Up Operation
The device includes a high-voltage current source connected between the HVIN pin and the internal supply for
the regulator. When the voltage on the HVIN pin rises, the current source is activated and starts to supply current
to the internal 5-V regulator. The 5-V regulator charges the external capacitor connected between VDD pin and
GND pin. When the VDD voltage exceeds the VDD turn-on threshold, VVDD(on), device starts operations. The
minimum voltage across HVIN and GND pins, to ensure enough current to charge the capacitance on VDD pin,
is VHVIN(min). At the First switching cycle the minimum MOSFET off time is set to be >100 μs and cycle-by-cycle is
progressively reduced up to tOFF(min) providing soft start.
8.4.2 Feedback and Voltage Control Loop
The feedback circuit consists of a voltage comparator with the positive input connected to an internal reference
voltage (referenced to GND) and the negative input connected to FB pin. When the feedback voltage at the FB
pin is below the reference voltage VFB_TH logic high is generated at the comparator output. This logic high
triggers the PWM controller, which generates the PWM signal turning on the MOSFET. When the feedback
voltage at the FB pin is above the reference voltage, it indicates that the output voltage of the converter is above
the targeted output voltage set by the external feedback circuitry and PWM is stopped.
12
Copyright © 2015–2016, Texas Instruments Incorporated
UCC28881
www.ti.com.cn
ZHCSEL3B –NOVEMBER 2015–REVISED JANUARY 2016
Device Functional Modes (continued)
8.4.3 PWM Controller
UCC28881 operates under on/off control. When the FB pin voltage is below internal reference 1 V, the converter
is switching and sending power to the load. When the FB pin voltage is above internal reference 1 V, the
converter shuts off and stops delivering power to the load.
The PWM controller does not need a clock signal. The PWM signal’s frequency is set to fSW(max) = (1/(tON(max)
tOFF(min))) which occurs when the voltage on the FB pin is continuously below VFB_TH
+
.
PWM duty cycle is determined by both the peak current and maximum on time. At each switching cycle, after
turn on, the MOSFET is turned off if its current reaches the fixed peak-current threshold or its on time reaches
the maximum value of on-time pulse tON(max)
.
Normally the converter would operate under frequency control, which means the converter is only enabled one
switching cycle and then disabled. Next switching cycle starts when output voltage decays and the feedback
enable the converter again. This way, the converter appears to operate under variable switching frequency
control.
The user might observe the converter operates in burst mode that converter is enabled for multiple switching
cycles and then stopped for multiple switching cycles. This causes larger output voltage ripple. However, due to
the infrequent switching it actually helps on the standby power at no load.
VFB
VFB_TH
t
FB_COMP_OUT
t
PWM
t
CURRENT LIMIT
t
RSTN
t
GATE
t
tON(max)
tOFF(min)
tON(max)
tOFF(min)
tON(max)
tOFF(min)
tON(max)
tOFF(min)
Figure 13. UCC28881 Timing Diagram
Copyright © 2015–2016, Texas Instruments Incorporated
13
UCC28881
ZHCSEL3B –NOVEMBER 2015–REVISED JANUARY 2016
www.ti.com.cn
Device Functional Modes (continued)
8.4.4 Current Limit
The current limit circuit senses the current through the power MOSFET. The sensing circuit is located between
the source of the power MOSFET and the GND pin. When the current in the power MOSFET exceeds the
threshold ILIMIT, the internal current limit signal goes high, which sets the internal RSTN signal low. This disables
the power MOSFET by driving its gate low. The current limit signal is set back low after the falling edge of the
PWM signal. After the rising edge of the GATE signal, there is a blanking time. During this blanking time, the
current limit signal cannot go high. This blanking time and the internal propagation delay result in minimum on
time, tMIN
.
8.4.5 Inductor Current Runaway Protection
To protect the device from overload conditions, including a short circuit at the output, the PWM controller
incorporates a protection feature which prevents the inductor current from runaway. When the output is shorted
the inductor demagnetization is very slow, with low di/dt, and when the next switching cycle starts energy stored
in the inductance is still high. After the MOSFET switches on, the current starts to rise from pre-existing DC value
and reaches the current-limit value in a short duration of time. Because of the intrinsic minimum on-time of the
device the MOSFET on-time cannot be lower than tMIN, in an overload or output short circuit the energy
inductance is not discharged sufficiently during MOSFET off-time, it is possible to lose control of the current
leading to a runaway of the inductor current. To avoid this, if the on-time is less than tON_TO (tON_TO is a device
internal time out), the controller increases the MOSFET off-time (tOFF). If the MOSFET on-time is longer than
tON_TO then tOFF is decreased. The controller increases tOFF, cycle-by-cycle, through discrete steps until the on-
time continues to stay below tON_TO. The tOFF is increased up to tOFF(ovl) after that, if the on-time is still below
tON_TO the off-time is kept equal to tOFF(ovl). The controller decreases tOFF cycle-by-cycle until the on-time
continues to stay above tON_TO up to tOFF(min). This mechanism prevents control loss of the inductor current and
prevents over stress of the MOSFET (see typical waveforms in Figure 14 and Figure 15). At start up, the tOFF is
set to tOFF(ovl) and reduced cycle-by-cycle (if the on-time is longer than tON_TO) up to tOFF(min) providing a soft start
for the power stage.
L[LaLÇ
Lnducꢁor /urrenꢁ
5rꢀin /urrenꢁ
t
t
ꢁhb_a!ó
ꢁhCC
tía
/urrenꢁ [imiꢁ
[9.
t
t
~200 ns
ꢁhb_Çh
~200 ns
ꢁhb_Çh
ꢁhb_Çh
t
t
Lncreꢀse ꢁ
( 5ecreꢀse f{í
5ecreꢀse ꢁhCC
(Lncreꢀse f{í
hCC
)
)
/bÇ_Lb
Dꢀꢁe
t
tON
tON
Figure 14. Current Runaway Protection Logic Timing Diagram
14
Copyright © 2015–2016, Texas Instruments Incorporated
UCC28881
www.ti.com.cn
ZHCSEL3B –NOVEMBER 2015–REVISED JANUARY 2016
Device Functional Modes (continued)
hutput {ꢀorted Iere
VFB
VFB_TH
ILIMIT
Lb5Ü/Çhw
/Üww9bÇ
5w!Lb
/Üww9bÇ
t
t
tON_TO
D!Ç9
tON_TO
tON_TO
tON_TO
tON_TO
t
tON < tON_TO
tON > tON_TO
tON < tON_TO
tON < tON_TO
Figure 15. Current Runaway Protection, Inductor and MOSFET Current
A minimal value needs to be imposed on the inductance value to avoid nuisance tripping of the protection feature
that prevents the loss of control of the inductor current. Inadvertent operation of the protection feature limits the
output-power capability of the converter. This condition depends on the converter's maximum input operating
voltage and temperature. Use Equation 1 to calculate your minimum inductance value.
V
IN max
(
)
L >
ì tON_ TO
ILIMIT
(1)
In this equation, VIN(max) is the maximum voltage on the DC input. If the input is a rectifed AC voltage, it should
be the peak value of the maximum AC line. For a DC input case, it should be the maximum DC input voltage.
If the inductance value is too low, such that the MOSFET on-time is always less than tON_TO timeout and the
device progressively increases the MOSFET off-time up to tOFF(ovl), the output power is reduced and the
converter fails to supply the load.
8.4.6 Over Temperature Protection
If the junction temperature rises above TJ(stop), the over temperature protection is triggered. This disables the
power MOSFET switching. To re-enable the switching of the MOSFET the junction temperature has to fall by
TJ(hyst) below the TJ(stop) where the device moves out of over temperature protection.
Copyright © 2015–2016, Texas Instruments Incorporated
15
UCC28881
ZHCSEL3B –NOVEMBER 2015–REVISED JANUARY 2016
www.ti.com.cn
9 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
9.1 Application Information
The UCC28881 can be used in various application topologies with direct or isolated feedback. The device can be
used in low-side buck, where the output voltage is negative, or as a low-side buck-boost configuration, where the
output voltage is positive. In both configurations the common reference node is the positive input node (VIN+).
The device can also be configured as a LED driver in either of the above mentioned configurations. If the
application requires the AC-to-DC power supply output to be referenced to the negative input node (VIN–), the
UCC28881 can also be configured as a traditional high-side buck as shown in Figure 16. In this configuration,
the voltage feedback is sampling the output voltage VOUT, making the DC regulation less accurate and load
dependent than in low-side buck configuration, where the feedback is always tracking the VOUT. However, high-
conversion efficiency can still be obtained.
9.2 Typical Application
9.2.1 13-V, 225-mA High-Side Buck Converter
Figure 16 shows a typical application example of a non-isolated power supply, where the UCC28881 is
connected in a high-side buck configuration having an output voltage that is positive with respect to the negative
high-voltage input (VIN–). The output voltage is set to 13 V in this example, but can easily be changed by
changing the value of RFB1. This application can be used for a wide variety of household appliances and
automation, or any other applications where mains isolation is not required.
L2
RF
D2
HVIN
VDD
FB
DRAIN
UCC28881
GND
CVDD
C1
+
VIN
-
RFB1
C2
CFB
RFB2
D4
L1
+
D1
CL
RL
VOUT
-
D3
Figure 16. Universal Input, 12-V, 225-mA Output High-Side Buck
16
Copyright © 2015–2016, Texas Instruments Incorporated
UCC28881
www.ti.com.cn
ZHCSEL3B –NOVEMBER 2015–REVISED JANUARY 2016
Typical Application (continued)
9.2.1.1 Design Requirements
Table 2. Design Specification
DESCRIPTION
DESIGN INPUT
MIN
TYP
MAX
UNIT
VIN
AC input voltage
Line frequency
Output current
85
47
0
265
63
VRMS
Hz
fLINE
IOUT
225
mA
DESIGN REQUIREMENTS
PNL
No-load input power
500
17.5
350
mW
V
VOUT
ΔVOUT
η
Output voltage
12.5
70%
13
Output voltage ripple
Converter full-load efficiency
mV
9.2.1.2 Detailed Design Procedure
9.2.1.2.1 Input Stage (RF, D2, D3, C1, C2, L2)
•
Resistor RF is a flame-proof fusible resistor. RF limits the inrush current, and also provide protection in case
any component failure causes a short circuit. Value for its resistance is generally selected between 4.7 Ω to
15 Ω.
•
A half-wave rectifier is chosen and implemented by diode D2 (1N4937). It is a general purpose 1-A, 600-V
rated diode. It has a fast reverse recovery time (200 ns) for improved differential-mode-conducted EMI noise
performance. Diode D3 (1N4007) is a general purpose 1-A, 1-kV rated diode with standard reverse recovery
time (>500 ns), and is added for improved common-mode-conducted EMI noise performance. D3 can be
removed and replaced by a short if not needed.
•
EMI filtering is implemented by using a single differential-stage filter (C1-L2-C2).
Capacitors C1 and C2 in the EMI filter also acts as storage capacitors for the high-voltage input DC voltage
(VIN). The required input capacitor size can be calculated according Equation 2.
»
…
…
…
ÿ
Ÿ
Ÿ
≈
∆
∆
«
’
÷
÷
◊
VBULK min
2ìP
1
1
(
)
IN
ì
-
ì arccos
fLINE min
RCT 2ì p
2 ì V
(
)
IN min
(
)
Ÿ
⁄
CBULK min
=
(
)
2ì V2
- VB2ULK min
IN min
where
•
•
•
•
•
•
CBULK(min) is minimum value for the total input capacitor value (C1 + C2 in the schematic of Figure 16).
RCT = 1 in case of half wave rectifier and RCT = 2 in case of full-wave rectifier .
PIN is the converter input power.
VIN(min) is the minimum RMS value of the AC input voltage.
VBULK(min) is the minimum allowed voltage value across bulk capacitor during converter operation.
fLINE(min) is the minimum line frequency when the line voltage is VIN(min)
.
The converter input power can be easily calculated as follow:
•
•
The converter maximum output power is: POUT = IOUT x VOUT = 0.225 A x 13 V = 2.925 W
Assuming the efficiency η = 68% the input power is PIN = POUT/η = 4.178 W
Using the following values for the other parameters
•
•
•
VBULK(min) = 80 V
VIN(min) = 85 VRMS (from design specification table)
fLINE(min) = 57 Hz
(2)
17
Copyright © 2015–2016, Texas Instruments Incorporated
UCC28881
ZHCSEL3B –NOVEMBER 2015–REVISED JANUARY 2016
www.ti.com.cn
CBULK(min) = 15.6 μF. Considering that electrolytic capacitors, generally used as bulk capacitor, have 20% of
tolerance in value, the minimum nominal value required for CBULK is:
CBULK(min)
CBULKn(min)
>
= 19.5mF
1- TOL
CBULK
(3)
Select C1 and C2 to be 10 μF each (CBULK = 10 μF + 10 μF = 20 μF > CBULKn(min)).
By using a full-wave rectifier allows a smaller capacitor for C1 and C2, almost 50% smaller.
9.2.1.2.2 Regulator Capacitor (CVDD
)
Capacitor CVDD acts as the decoupling capacitor and storage capacitor for the internal regulator. A 100-nF, 10-V
rated ceramic capacitor is enough for proper operation of the device's internal LDO.
9.2.1.2.3 Freewheeling Diode (D1)
The freewheeling diode has to be rated for high-voltage with as short as possible reverse-recovery time (trr).
The maximum reverse voltage that the diode should experience in the application, during normal operation, is
given by Equation 4.
VD1(max) = 2ìVIN(max) = 2ì265V =375V
(4)
A margin of 20% is generally considered.
The use of a fast recovery diode is required for the buck-freewheeling rectifier. When designed in CCM, the
diode reverse recovery time should be less than 35 ns to keep low reverse recovery current and the switching
loss. For example, STTH1R06A provides 25-ns reverse recovery time. When designed in DCM, slower diode can
be used, but the reverse recovery time should be kept less than 75 ns. MURS160 can fit the requirement.
9.2.1.2.4 Output Capacitor (CL)
The value of the output capacitor impacts the output ripple. Depending on the combination of capacitor value and
equivalent series resistor (RESR). A larger capacitor value also has an impact on the start-up time. For a typical
application, the capacitor value can start from 47 μF, to hundreds of μF. A guide for sizing the capacitor value
can be calculated by the following equations:
ILIMIT -IOUT
440mA - 225mA
62kHz ì350mV
CL > 20 ì
= 20 ì
= 200mF
fSW max ì DVOUT
(5)
(6)
DVOUT
ILIMIT
RESR
<
= 0.8W
Take into account that both CL and RESR contribute to output voltage ripple. A first pass capacitance value can be
selected and the contribution of CL and RESR to the output voltage ripple can be evaluated. If the total ripple is
too high the capacitance value has to increase or RESR value must be reduced. In the application example CL
was selected (330 µF) and it has an RESR of 0.03 Ω. So the RESR contributes for 4% of the total ripple. The
formula that calculates CL is based on the assumption that the converter operates in burst of twenty switching
cycles. The number of bursts per cycle could be different, the formula for CL is a first approximation.
9.2.1.2.5 Pre-Load Resistor (RL)
The pre-load resistor connected at the output is required for the high-side buck topology. Unlike low side buck
topology, the output voltage is directly sensed, in high-side buck topology the output is sampled and estimated.
At no-load condition, because the feedback loop runs with its own time constant, the buck converter operates
with a fixed minimum switching frequency. Select the pre-load resistor or using a zener diode to prevent output
voltage goes too high at no-load condition.
A simple zener diode would be a good choice without going through the calculation. Besides the simplifying the
calculation, zener diode doesn't consumes power at heavy load condition, which helps to improve the converter
heavy-load efficiency.
18
Copyright © 2015–2016, Texas Instruments Incorporated
UCC28881
www.ti.com.cn
ZHCSEL3B –NOVEMBER 2015–REVISED JANUARY 2016
A simple resistor can also be used to limit the output voltage at no load condition. However, this resistor
connects to the output all the time and it reduces the full-load efficiency. The pre-load resistor can be calculated
based on below equation or based on experiments. In this equation, the VMAX is allowed maximum output
voltage, and VREG is the regulated output voltage.
4ì VMAX2 ì V
- VREG CFB ì RFB1 +RFB2
(
)
(
)
MAX
RL =
ì
2
VMAX + VREG
L1 ìILIMIT
(7)
9.2.1.2.6 Inductor (L1)
Initial calculations:
Half of the peak-to-peak ripple current at full load:
DI = 2ì I -IOUT
L
LIMIT
(8)
When operating in DCM, the peak-to-peak current ripple is the peak current of the device.
Average MOSFET conduction minimum duty cycle at continuous conduction mode is:
VOUT + Vd
DMIN
=
VIN(max) - Vd
(9)
(10)
(11)
If the converter operates in discontinuous conduction mode:
IOUT VOUT + Vd
DMIN = 2ì
ILIMIT
VIN(max) - Vd
Maximum allowed switching frequency at VIN(max) and full load:
DMIN
FSW _ VIN(max)
=
tON_ TO
Switching frequency has a maximum value limit of fSW(max)
The worst case ILIMIT = 315 mA, but assuming ΔIL = 180 mA.
.
The converter works in continuous conduction mode (ΔIL < ILIMIT) so based on VOUT = 13 V, Vd = 0.5 V and
VIN(max) = 375 V
VOUT + Vd
DMIN
=
= 3.61%
VIN(max) - Vd
(12)
The maximum allowed switching frequency is 62 kHz because the calculated value exceeds it.
DMIN
FSW _ VIN(max)
=
= 80kHz >fSW(max) = 62kHz
tON_ TO
(13)
The duty cycle does not force the MOSFET on time to go below tON_TO. If DMIN/TON_TO < fSW(max), the switching
frequency is reduced by current runaway protection and the maximum average switching frequency is lower than
fSW(max), the converter can't support full load.
The minimum inductance value satisfies both the following conditions:
VOUT + Vd
L >
= 1mH
DIL ìFSW _ VIN max
(14)
(15)
V
IN max
375V
(
)
L >
ì tON_ TO
=
ì 450ns @ 536mH
ILIMIT
315mA
In the application example, 1 mH is selected as the minimum standard value that satisfy Equation 14 and
Equation 15.
Copyright © 2015–2016, Texas Instruments Incorporated
19
UCC28881
ZHCSEL3B –NOVEMBER 2015–REVISED JANUARY 2016
www.ti.com.cn
9.2.1.2.7 Feedback Path (CFB, RFB1 and RFB2) and Load Resistor (RL)
In low-side buck converter the output voltage is always sensed by the FB pin and UCC28881 internal controller
can turn on the MOSFET on VOUT. In high-side buck converter applications the information on the output
voltage value is stored on CFB capacitor. This information is not updated in real time. The information on CFB
capacitor is updated just after MOSFET turn-off event. When the MOSFET is turned off, the inductor current
forces the freewheeling diode (D1 in Figure 16) to turn on and the GND pin of UCC28881 goes negative at -Vd1
(where Vd1 is the forward drop voltage of diode D1) with respect to the negative terminal of bulk capacitor (C1 in
Figure 16). When D1 is on, through diode D4, the CFB capacitor is charged at VOUT – Vd4 + Vd1. Set the output
voltage regulation level using Equation 16.
VOUT(T) - Vd4 + Vd1 - VFB _ TH VOUT(T) - VFB _ TH
RFB1
RFB2
=
@
VFB _ TH
VFB _ TH
where
•
•
•
•
•
VFB_TH is the FB pin reference voltage.
VOUT_T is the target output voltage.
RFB1, RFB2 is the resistance of the resistor divider connected with FB pin (see Figure 16)
The capacitor CFB after D1 is discharged with a time constant that is τFB = CFB x (RFB1 + RFB2 ).
Select the time constant τFB, given in Equation 17
(16)
(17)
tFB = CFB ì RFB1 +RFB2 = 0.1ìC ìR
L
LOAD
In this equation, RLOAD is the full load resistor value.
The time constant selection leads to a slight output-voltage increase in no-load or light-load conditions. In order
to reduce the output-voltage increase, increase τFB. The drawback of increasing τFB is t in high-load conditions
VOUT could drop.
Because of the nature of sample and hold of output voltage feedback, the feedback loop components need some
adjustment after the initial design. The larger time constant of the feedback components leads to lower no-load
switching frequency. As the results, the no-load standby power and light-load voltage regulation are improved.
Because of larger time constant, at heavier load, the load regulation start to get worse. On the contrast,
decreasing the time constant makes the heavy load regulation better but increases the no-load standby power
and makes the light-load voltage regulation worse. Some tradeoff is required to make the regulation and standby
power. Below table summarizes the relationship between the feedback loop time constant and the load
regulation. This can be used for an easy guideline for fine tuning the circuit performance.
Table 3. Feedback Loop Time Constant Adjustment
FEEDBACK LOOP TIME
HEAVY-LOAD OUTPUT
VOLTAGE RIPPLE
NO-LOAD REGULATION
STANDBY POWER
CONSTANT (τFB
)
Increase
Better
Worse
Worse
Better
Better
Worse
Decrease
20
Copyright © 2015–2016, Texas Instruments Incorporated
UCC28881
www.ti.com.cn
ZHCSEL3B –NOVEMBER 2015–REVISED JANUARY 2016
9.2.1.3 Application Curves
Figure 17 shows the output voltage vs output current. Different curves correspond to different converter AC input
voltages. Figure 18 shows efficiency changes vs output power. Different curves correspond to different converter
AC input voltages.
18
16
14
12
10
8
100
90
80
70
60
50
40
30
20
10
0
115V AC
230V AC
6
4
115V AC
230V AC
2
0
0
0.05
0.1
0.15
0.2
0.25
0
0.3 0.6 0.9 1.2 1.5 1.8 2.1 2.4 2.7
Output Power (W)
3
Output Current (A)
D001
D001
Figure 17. Output IV Characteristic
Figure 18. Efficiency vs POUT
Table 4. Converter Efficiency
VIN_AC (VRMS
)
LOAD (mA)
EFFICIENCY (%)
AVERAGE EFFICIENCY (%)
115
50
82
81
81
80
80
81
81
81
81
100
150
225
50
230
80.8
100
150
225
Table 5. Key Component List for 13-V 225-mA High-Side Buck Converter
DES
DESCRIPTION
Bulk capacitor, 10 μF, 450 V
PART NUMBER
EEUED2W100
MANUFACTURER(1)
C1, C2
CFB
Panasonic
Feedback capacitor, ceramic, 0.015 μF, 50 V
Output capacitor, 330 μF, 35 V
C0805C153K5RACTU
EEU-FM1V331L
STTH1R06A
Kemet
CL
Panasonic
D1
Buck freewheeling diode, ultrafast, 600 V, 1 A
ST Microelectronics
Fairchild semiconductor
D2, D3
Rectifier diodes, standard recovery rectifier, 1000
V, 1 A
1N4007
D4
Feedback diode, standard recovery rectifier, 600 V, 1N4006-T
1 A
Diodes Inc.
L1
L2
Buck inductor, 1 mH, 0.4 A,
7447471102
Wurth Elektronik
Bourns
Filter inductor, 1 mH, 0.2 A
5800-102-RC
RFB1
RFB2
Upper feedback resistor 121 kΩ, 1%
Lower feedback resistor, 10.0 kΩ, 1%
ERJ-6ENF1213V
ERJ-6ENF1002V
Panasonic
Panasonic
(1) See Third-Party Products Discalimer
Copyright © 2015–2016, Texas Instruments Incorporated
21
UCC28881
ZHCSEL3B –NOVEMBER 2015–REVISED JANUARY 2016
www.ti.com.cn
9.2.2 Additional UCC28881 Application Topologies
9.2.2.1 Low-Side Buck and LED Driver – Direct Feedback (Level Shifted)
Features include:
•
•
•
•
Output Referenced to Input
Negative Output (VOUT) with Respect to VIN+
Step Down: VOUT < VIN
Direct Level-Shifted Feedback
RFB1
D1
+
CL
VOUT
-
Q1
L1
HVIN
+
VIN
-
VDD
FB
DRAIN
UCC28881
GND
RFB2
Figure 19. Low-Side Buck, Direct Feedback (Level Shifted)
RSENSE
C1
R2
Q2
D1
RFB1
CL
R1
+
Current Feedback
L1
VIN
-
HVIN
VOUT
VDD
FB
DRAIN
Q1
UCC28881
GND
RFB1
Figure 20. Low-Side Buck LED Driver, Direct Feedback (Level Shifted)
22
Copyright © 2015–2016, Texas Instruments Incorporated
UCC28881
www.ti.com.cn
ZHCSEL3B –NOVEMBER 2015–REVISED JANUARY 2016
9.2.2.2 High-Side Buck Converter
Features include:
•
•
•
Output Referenced to Input
Positive Output (VOUT) with Respect to VIN–
Step Down (VOUT < VIN)
HVIN
VDD
FB
DRAIN
+
VIN
-
UCC28881
GND
10 ꢀ
D2
CFB
RFB2
L1
+
D1
CL
VOUT
-
Figure 21. High-Side Buck Converter Schematic
9.2.2.3 Non-Isolated, Low-Side Buck-Boost Converter
Features Include:
•
•
•
•
Output Referenced to Input
Positive Output (VOUT) with Respect to VIN+
Step Up, Step Down: VOUT > VIN or VOUT < VIN
Direct Level-Shifted Feedback
CL
+
VOUT
-
D1
L1
HVIN
VDD
DRAIN
+
VIN
-
UCC28881
FB
GND
RFB2
Figure 22. Low-Side Buck-Boost Converter
Copyright © 2015–2016, Texas Instruments Incorporated
23
UCC28881
ZHCSEL3B –NOVEMBER 2015–REVISED JANUARY 2016
www.ti.com.cn
9.2.2.4 Non-Isolated, High-Side Buck-Boost Converter
Features include:
•
•
•
Output Referenced to Input
Positive Output (VOUT) with Respect to VIN–
Step Up, Step Down: VOUT > VIN or VOUT < VIN
HVIN
VDD
FB
DRAIN
UCC28881
GND
+
VIN
-
RFB1
D2
CFB
RFB2
+
D1
CL
VOUT
L1
-
Figure 23. High-Side Buck-Boost Converter
9.2.2.5 Non-Isolated Flyback Converter
Features include:
•
•
•
•
Output Referenced to Input
Positive Output (VOUT) with Respect VIN–
Direct Feedback
Higher Output Current Capability, 4.5 W for 85 VAC ~ 265 VAC Input and 6 W for 176 VAC ~ 265 VAC Input
RFB1
CL
HVIN
+
+
VDD
FB
DRAIN
VOUT
-
VIN
-
UCC28881
GND
CVDD
RFB2
Figure 24. Non-Isolated Flyback Configuration
24
Copyright © 2015–2016, Texas Instruments Incorporated
UCC28881
www.ti.com.cn
ZHCSEL3B –NOVEMBER 2015–REVISED JANUARY 2016
9.2.2.6 Isolated Flyback Converter
Features include:
•
•
•
Output Isolated from Input
Direct Feedback
Higher Output Current Capability, 4.5 W for 85 VAC ~ 265 VAC Input and 6 W for 176 VAC ~ 265VAC Input
+
CL
VOUT
-
HVIN
+
VIN
-
VDD
FB
DRAIN
UCC28881
GND
CVDD
RFB
Figure 25. Isolated Flyback Converter
Copyright © 2015–2016, Texas Instruments Incorporated
25
UCC28881
ZHCSEL3B –NOVEMBER 2015–REVISED JANUARY 2016
www.ti.com.cn
10 Power Supply Recommendations
The VDD capacitor recommended value is 100 nF to ensure high-phase margin of the internal 5-V regulator and
it should be placed close to VDD pin and GND pins to minimize the series resistance and inductance.
The VDD pin provides a regulated 5-V output but it is not intended as a supply for external load. Do not supply
VDD pin with external voltage source (for example the auxiliary winding of flyback converter).
Always keep GND pin 1 and GND pin 2 connected together with the shortest possible connection.
11 Layout
11.1 Layout Guidelines
•
•
•
In both buck and buck-boost low-side configurations, the copper area of the switching node DRAIN should be
minimized to reduce EMI.
Similarly, the copper area of the FB pin should be minimized to reduce coupling to feedback path. Loop CL,
Q1, RFB1 should be minimized to reduce coupling to feedback path.
In high-side buck and buck boost the GND, VDD and FB pins are all part of the switching node so the copper
area connected with these pins should be optimized. Large copper area allows better thermal management,
but it causes more common mode EMI noise. Use the minimum copper area that is required to handle the
thermal dissipation.
•
Minimum distance between 700-V coated traces is 1.41 mm (60 mils).
11.2 Layout Example
Figure 26 shows and example PCB layout for UCC28881 in low-side buck configuration.
L2
D2
Rf
C1
C2
AC
INPUT
D3
GND_IC
GND_IC
FB
DRAIN
L1
D1
NC
VDD
HVIN
Rfb1
Rfb2
Q1
= top layer
= bottom layer
= connect top and bot
CL
RL
DC
OUTPUT
Figure 26. UCC28881 Layout Example
26
版权 © 2015–2016, Texas Instruments Incorporated
UCC28881
www.ti.com.cn
ZHCSEL3B –NOVEMBER 2015–REVISED JANUARY 2016
12 器件和文档支持
12.1 器件支持
12.1.1 Third-Party Products Disclaimer
TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT
CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES
OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER
ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.
12.2 社区资源
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
12.3 商标
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
12.4 静电放电警告
这些装置包含有限的内置 ESD 保护。 存储或装卸时,应将导线一起截短或将装置放置于导电泡棉中,以防止 MOS 门极遭受静电损
伤。
12.5 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
13 机械、封装和可订购信息
以下页中包括机械、封装和可订购信息。这些信息是针对指定器件可提供的最新数据。这些数据会在无通知且不对
本文档进行修订的情况下发生改变。欲获得该数据表的浏览器版本,请查阅左侧的导航栏。
版权 © 2015–2016, Texas Instruments Incorporated
27
重要声明
德州仪器(TI) 及其下属子公司有权根据 JESD46 最新标准, 对所提供的产品和服务进行更正、修改、增强、改进或其它更改, 并有权根据
JESD48 最新标准中止提供任何产品和服务。客户在下订单前应获取最新的相关信息, 并验证这些信息是否完整且是最新的。所有产品的销售
都遵循在订单确认时所提供的TI 销售条款与条件。
TI 保证其所销售的组件的性能符合产品销售时 TI 半导体产品销售条件与条款的适用规范。仅在 TI 保证的范围内,且 TI 认为 有必要时才会使
用测试或其它质量控制技术。除非适用法律做出了硬性规定,否则没有必要对每种组件的所有参数进行测试。
TI 对应用帮助或客户产品设计不承担任何义务。客户应对其使用 TI 组件的产品和应用自行负责。为尽量减小与客户产品和应 用相关的风险,
客户应提供充分的设计与操作安全措施。
TI 不对任何 TI 专利权、版权、屏蔽作品权或其它与使用了 TI 组件或服务的组合设备、机器或流程相关的 TI 知识产权中授予 的直接或隐含权
限作出任何保证或解释。TI 所发布的与第三方产品或服务有关的信息,不能构成从 TI 获得使用这些产品或服 务的许可、授权、或认可。使用
此类信息可能需要获得第三方的专利权或其它知识产权方面的许可,或是 TI 的专利权或其它 知识产权方面的许可。
对于 TI 的产品手册或数据表中 TI 信息的重要部分,仅在没有对内容进行任何篡改且带有相关授权、条件、限制和声明的情况 下才允许进行
复制。TI 对此类篡改过的文件不承担任何责任或义务。复制第三方的信息可能需要服从额外的限制条件。
在转售 TI 组件或服务时,如果对该组件或服务参数的陈述与 TI 标明的参数相比存在差异或虚假成分,则会失去相关 TI 组件 或服务的所有明
示或暗示授权,且这是不正当的、欺诈性商业行为。TI 对任何此类虚假陈述均不承担任何责任或义务。
客户认可并同意,尽管任何应用相关信息或支持仍可能由 TI 提供,但他们将独力负责满足与其产品及在其应用中使用 TI 产品 相关的所有法
律、法规和安全相关要求。客户声明并同意,他们具备制定与实施安全措施所需的全部专业技术和知识,可预见 故障的危险后果、监测故障
及其后果、降低有可能造成人身伤害的故障的发生机率并采取适当的补救措施。客户将全额赔偿因 在此类安全关键应用中使用任何 TI 组件而
对 TI 及其代理造成的任何损失。
在某些场合中,为了推进安全相关应用有可能对 TI 组件进行特别的促销。TI 的目标是利用此类组件帮助客户设计和创立其特 有的可满足适用
的功能安全性标准和要求的终端产品解决方案。尽管如此,此类组件仍然服从这些条款。
TI 组件未获得用于 FDA Class III(或类似的生命攸关医疗设备)的授权许可,除非各方授权官员已经达成了专门管控此类使 用的特别协议。
只有那些 TI 特别注明属于军用等级或“增强型塑料”的 TI 组件才是设计或专门用于军事/航空应用或环境的。购买者认可并同 意,对并非指定面
向军事或航空航天用途的 TI 组件进行军事或航空航天方面的应用,其风险由客户单独承担,并且由客户独 力负责满足与此类使用相关的所有
法律和法规要求。
TI 已明确指定符合 ISO/TS16949 要求的产品,这些产品主要用于汽车。在任何情况下,因使用非指定产品而无法达到 ISO/TS16949 要
求,TI不承担任何责任。
产品
应用
www.ti.com.cn/telecom
数字音频
www.ti.com.cn/audio
www.ti.com.cn/amplifiers
www.ti.com.cn/dataconverters
www.dlp.com
通信与电信
计算机及周边
消费电子
能源
放大器和线性器件
数据转换器
DLP® 产品
DSP - 数字信号处理器
时钟和计时器
接口
www.ti.com.cn/computer
www.ti.com/consumer-apps
www.ti.com/energy
www.ti.com.cn/dsp
工业应用
医疗电子
安防应用
汽车电子
视频和影像
www.ti.com.cn/industrial
www.ti.com.cn/medical
www.ti.com.cn/security
www.ti.com.cn/automotive
www.ti.com.cn/video
www.ti.com.cn/clockandtimers
www.ti.com.cn/interface
www.ti.com.cn/logic
逻辑
电源管理
www.ti.com.cn/power
www.ti.com.cn/microcontrollers
www.ti.com.cn/rfidsys
www.ti.com/omap
微控制器 (MCU)
RFID 系统
OMAP应用处理器
无线连通性
www.ti.com.cn/wirelessconnectivity
德州仪器在线技术支持社区
www.deyisupport.com
IMPORTANT NOTICE
邮寄地址: 上海市浦东新区世纪大道1568 号,中建大厦32 楼邮政编码: 200122
Copyright © 2016, 德州仪器半导体技术(上海)有限公司
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
UCC28881D
ACTIVE
ACTIVE
SOIC
SOIC
D
D
7
7
75
RoHS & Green
NIPDAU
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
-40 to 125
-40 to 125
U28881
U28881
UCC28881DR
2500 RoHS & Green
NIPDAU
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
Addendum-Page 2
PACKAGE OUTLINE
D0007A
SOIC - 1.75 mm max height
SCALE 2.800
SMALL OUTLINE INTEGRATED CIRCUIT
C
SEATING PLANE
.228-.244 TYP
[5.80-6.19]
.004 [0.1] C
A
PIN 1 ID AREA
8
1
.100
[2.54]
2X
.189-.197
[4.81-5.00]
NOTE 3
.150
[3.81]
4X .050
[1.27]
4
5
7X .012-.020
[0.31-0.51]
B
.150-.157
[3.81-3.98]
NOTE 4
.069 MAX
[1.75]
.010 [0.25]
C A B
.005-.010 TYP
[0.13-0.25]
SEE DETAIL A
.010
[0.25]
.004-.010
[0.11-0.25]
0 - 8
.016-.050
[0.41-1.27]
DETAIL A
TYPICAL
(.041)
[1.04]
4220728/A 01/2018
NOTES:
1. Linear dimensions are in inches [millimeters]. Dimensions in parenthesis are for reference only. Controlling dimensions are in inches.
Dimensioning and tolerancing per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed .006 [0.15] per side.
4. This dimension does not include interlead flash.
5. Reference JEDEC registration MS-012, variation AA.
www.ti.com
EXAMPLE BOARD LAYOUT
D0007A
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
7X (.061 )
[1.55]
SYMM
SEE
DETAILS
1
8
7X (.024)
[0.6]
(.100 )
[2.54]
SYMM
5
4
4X (.050 )
[1.27]
(.213)
[5.4]
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE:8X
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
METAL
EXPOSED
METAL
EXPOSED
METAL
.0028 MAX
[0.07]
ALL AROUND
.0028 MIN
[0.07]
ALL AROUND
SOLDER MASK
DEFINED
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
4220728/A 01/2018
NOTES: (continued)
6. Publication IPC-7351 may have alternate designs.
7. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
D0007A
SOIC - 1.75 mm max height
SMALL OUTLINE INTEGRATED CIRCUIT
7X (.061 )
[1.55]
SYMM
1
8
7X (.024)
[0.6]
(.100 )
[2.54]
SYMM
5
4
4X (.050 )
[1.27]
(.213)
[5.4]
SOLDER PASTE EXAMPLE
BASED ON .005 INCH [0.125 MM] THICK STENCIL
SCALE:8X
4220728/A 01/2018
NOTES: (continued)
8. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
9. Board assembly site may have different recommendations for stencil design.
www.ti.com
重要声明和免责声明
TI 均以“原样”提供技术性及可靠性数据(包括数据表)、设计资源(包括参考设计)、应用或其他设计建议、网络工具、安全信息和其他资
源,不保证其中不含任何瑕疵,且不做任何明示或暗示的担保,包括但不限于对适销性、适合某特定用途或不侵犯任何第三方知识产权的暗示
担保。
所述资源可供专业开发人员应用TI 产品进行设计使用。您将对以下行为独自承担全部责任:(1) 针对您的应用选择合适的TI 产品;(2) 设计、
验证并测试您的应用;(3) 确保您的应用满足相应标准以及任何其他安全、安保或其他要求。所述资源如有变更,恕不另行通知。TI 对您使用
所述资源的授权仅限于开发资源所涉及TI 产品的相关应用。除此之外不得复制或展示所述资源,也不提供其它TI或任何第三方的知识产权授权
许可。如因使用所述资源而产生任何索赔、赔偿、成本、损失及债务等,TI对此概不负责,并且您须赔偿由此对TI 及其代表造成的损害。
TI 所提供产品均受TI 的销售条款 (http://www.ti.com.cn/zh-cn/legal/termsofsale.html) 以及ti.com.cn上或随附TI产品提供的其他可适用条款的约
束。TI提供所述资源并不扩展或以其他方式更改TI 针对TI 产品所发布的可适用的担保范围或担保免责声明。IMPORTANT NOTICE
邮寄地址:上海市浦东新区世纪大道 1568 号中建大厦 32 楼,邮政编码:200122
Copyright © 2020 德州仪器半导体技术(上海)有限公司
相关型号:
©2020 ICPDF网 联系我们和版权申明