UCC3829DW-1 [TI]
High Speed PWM Controller 20-SOIC 0 to 70;型号: | UCC3829DW-1 |
厂家: | TEXAS INSTRUMENTS |
描述: | High Speed PWM Controller 20-SOIC 0 to 70 信息通信管理 开关 光电二极管 |
文件: | 总11页 (文件大小:190K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
UCC1829-1/-2/-3
UCC2829-1/-2/-3
UCC3829-1/-2/-3
High Speed PWM Controller
PRELIMINARY
FEATURES
DESCRIPTION
•
Compatible with Voltage or Current
Mode Control Methods
The UCC3829 is a BiCMOS High Speed PWM Controller IC. It is opti-
mized for high frequency switched mode power supply applications. The
IC can be used in both voltage mode and current mode control applica-
tions. Care was given to minimizing the propagation delays through the
comparators and logic circuitry while maximizing the bandwidth and slew
rate of the error amplifier. The oscillator frequency and deadtime can be
programmed via two external resistors and a capacitor. The undervolt-
age lockout threshold can be programmed using an external resistor di-
vider. The current limit and overcurrent threshold can be set externally.
The IC is available in push-pull (-1), single ended (-2), or complementary
(-3) output configuration.
•
Practical Operation at Switching
Frequencies to 4MHz
•
•
50ns Propagation Delay to Output
High Current Complementary
Outputs
•
Programmable Dead Time and
Frequency Oscillator
•
•
Pulse by Pulse Current Limiting
Fault protection circuitry includes undervoltage detection for the internal
bias supply, and overcurrent detection. The fault detection logic sets a
latch that ensures full discharge of the soft start capacitor before allowing
a restart. While the fault latch is set, the outputs are in a low state. In the
event of continuous faults, the soft start capacitor is fully charged before
discharging to insure that the fault frequency does not exceed the de-
signed soft start period.
Latched Overcurrent Comparator
with Full Cycle Restart
•
•
Programmable Undervoltage
Lockout (UVLO)
Adjustable Blanking for Leading
Edge Noise Tolerance
BLOCK DIAGRAM
BISYNC
RT1
9
8
18 VDD
VBIAS
15 OUTA
CT
7
6
CLOCK
>
S
R
Q
Q
Q
Q
T
RT2
14 OUTB
13 PGND
VBIAS
4V
LEB 19
11 CL+
1.5V
1.2V
RAMP
5
0.9V
12 CL–
PWCONT
EAOUT
NINV
4
3
1
2
1.25V
INV
VBIAS
14.2V/9V
3V/2.5V
2.1V
SS 10
S
R
Q
Q
1V
17 UVLO
23 VREF
3V
D
REFERENCE
GND 18
UDG-98043
SLUS390 - MARCH 1998
UCC1829-1/-2/-3
UCC2829-1/-2/-3
UCC3829-1/-2/-3
ABSOLUTE MAXIMUM RATINGS
ORDERING INFORMATION
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15V
Supply Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25mA
Output Current (OUTA, OUTB, PGND, VCC)
UCC 829
–
DC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5A
Pulsed (0.5µsec) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.2A
PGND. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±0.2V
Analog Inputs
INV, NINV, RAMP, SS . . . . . . . . . . . . . . . . . . . . . –0.3 to 7V
CL+, CL-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.3V to 3V
Error Amplifier Output Current . . . . . . . . . . . . . . . . . . . . . . 5mA
Error Amplifier Output Capacitance. . . . . . . . . . . . . . . . . . 20pF
Storage Temperature . . . . . . . . . . . . . . . . . . . –65°C to +150°C
Junction Temperature. . . . . . . . . . . . . . . . . . . –55°C to +150°C
Lead Temperature (Soldering, 10sec.) . . . . . . . . . . . . . +300°C
TEMPERATURE & PACKAGE SELECTION
GUIDE TABLE
TEMPERATURE
RANGE
AVAILABLE
PACKAGES
UCC1829-X
UCC2829-X
UCC3829-X
–55°C to +125°C
–40°C to +85°C
0°C to +70°C
J
N, DW, Q
N, DW, Q
Unless otherwise indicated, voltages are referenced to GND.
Currents are positive into, negative out of the specified terminal.
Consult Packaging Section of Databook for thermal limitations
and considerations of packages.
PART VERSION TABLE
PART NUMBER
UCCX829-1
UCCX829-2
UCCX829-3
OUTPUT
Push-Pull
OUT A/B PHASE
180° Out of Phase
In Phase
OUTPUT FREQUENCY
FCT/2
FCT
Dual Single-Ended
Non-Overlapping Complimentary
OUTB = OUTA
FCT
CONNECTION DIAGRAMS
DIL-20, SOIC-20 (Top View)
N, DW and J Packages
PLCC-20 (Top View)
Q Package
NINV
INV
VREF
LEB
NINV
INV
20 VREF
19 LEB
1
2
3
4
5
6
7
8
9
EAOUT
3
2
1
20 19
18
EAOUT
PWCONT
RAMP
RT2
18 GND
17 UVLO
16 VDD
15 OUTA
14 OUTB
13 PGND
12 CL–
PWCONT
RAMP
RT2
4
5
6
7
8
GND
17
16
15
14
UVLO
VDD
CT
OUTA
OUTB
RT1
9
10 11 12 13
CT
BISYNC
SS
PGND
CL–
RT1
BISYNC
CL+
SS 10
11 CL+
2
UCC1829-1/-2/-3
UCC2829-1/-2/-3
UCC3829-1/-2/-3
ELECTRICAL CHARACTERISTICS: Unless otherwise specified, RT1 = 34.8kΩ, CT = 470pF, RT2 = 392Ω, VDD = 12V,
Over Full Temperature Range and TA = TJ.
PARAMETER
Reference Section
TEST CONDITIONS
MIN
TYP
MAX UNITS
Output Voltage
TJ = 25°C, No Load, Output Off
2.97
2.94
3
3.03
3.06
50
V
V
Over Temperature, No Load, Output Off
VDD = 5V to 14.5V, Output Off, No Load, (Note 2)
0 < IREF < 5mA
Line Regulation
35
2
mV
mV
V
Load Regulation
Total Output Variation
10
Line, Load, Temperature = 0°C to 70°C, (Note 1)
2.93
2.90
3.07
3.10
Line, Load, Temperature = –55°C to +125°C,
(Note 1)
V
Short Circuit Current
Oscillator Section
Initial Accuracy
VREF = 0
–25
mA
TJ = 25°C
360
320
400
440
480
10
kHz
kHz
%
Total Variation
Line, Temperature (Note 1)
TMIN < TA < TMAX (Note 1)
RT1 = 25.7k, CT = 150pF, TJ = 25°C, (Note 1)
Temperature Stability
Initial Accuracy, 1MHz
Total Variation, 1MHz
5
1
0.9
0.8
1.1
1.2
MHz
MHz
RT1 = 25.7k, CT = 150pF, Line, Temperature
(Note 1)
Ramp Peak Voltage
Ramp Valley Voltage
Peak To Peak Voltage
BISYNC Output Source Current
BISYNC Output Sink Current
BISYNC Input Threshold
Error Amplifier Section
Input Offset Voltage
Input Bias Current
1.8
2
1
2.2
1.5
V
V
0.85
1
1.15
–1.5
V
VBISYNC = VDD – 0.5V
VBISYNC = 0.5V
–2
140
1.5
mA
A
60
1
2
V
5
1
mV
µA
nA
dB
dB
dB
µA
µA
V
–1
Input Offset Current
Open Loop Gain
250
70
75
80
CMRR
1.5V < VCM < 4.5V
5V < VDD < 14.5V
VEAOUT = 1V
PSRR
75
Output Sink Current
Output Source Current
Output High Voltage
Output Low Voltage
Gain Bandwidth Product
Slew Rate
300
500
VEAOUT = 4V
–500 –300
5
IEAOUT = –300µA
IEAOUT = 300µA
VDD = 12V, TJ = 25°C
3
0.6
7
1
V
5
MHz
V/µs
1.5
2
PWM Comparator Section
Input Bias Current V(RAMP)
Minimum Duty Cycle
Maximum Duty Cycle (UCCX829-1)
–60
1
0
µA
%
400kHz
400kHz, RT2 Resistor = 200Ω
42.5
85
%
Maximum Duty Cycle (UCCX829-2, -3) 400kHz, RT2 Resistor = 200Ω
Delay to Output
%
50
3
100
–10
ns
Current Limit Fault Section
Soft Start Charge Current
–40
µA
Soft Start Complete Threshold
SS Pin (Note 1)
V
3
UCC1829-1/-2/-3
UCC2829-1/-2/-3
UCC3829-1/-2/-3
ELECTRICAL CHARACTERISTICS: Unless otherwise specified, RT1 = 34.8kΩ, CT = 470pF, RT2 = 392Ω, VDD = 12V,
Over Full Temperature Range and TA = TJ.
PARAMETER
Restart Discharge Current
Restart Threshold
TEST CONDITIONS
MIN
10
TYP
MAX UNITS
40
1.2
1.1
1.4
100
400
µA
V
0.8
0.8
1.1
1
Current Limit Threshold
Overcurrent Threshold
Current Limit Delay to Output
Relative to CL–
Relative to CL–
0.875
1.25
50
V
V
ns
ns
VDD = 5V
100
Output Section (OUTA, OUTB)
Output Low Saturation
Output High Saturation
UVLO Output Low Saturation
Rise Time
IOUT = 200mA
IOUT = –100mA
At 10mA
0.5
0.5
1.0
1.0
0.5
40
V
V
0.1
V
CLOAD = 1nF, TJ = 25°C
CLOAD = 1nF, TJ = 25°C
VOUT = 0, TJ = 25°C (Note 1)
VOUT = 12V, TJ = 25°C (Note 1)
(Note 1)
20
ns
ns
A
Fall Time
10
20
Output Source Current
Output Sink Current
–0.75
1.5
A
Complementary Delay Time (Delay 2)
(UCCX829 -3 Only)
50
150
ns
Undervoltage Lockout
UVLO Enable Threshold
UVLO Hysteresis
VDD UVLO Enable Threshold
VDD UVLO Hysteresis
Supply Section
2.9
0.3
3
3.1
0.7
14.5
7
V
V
V
V
0.5
13.5
3.5
VDD Range
No Load
4.25
14.5
5
V
Startup Current
VUVLO = 2V, VDD = 13.5V
400kHz, No Load
3
8
mA
mA
IDD
12
Note 1: Guaranteed by design. Not 100% tested in production.
Note 2: Refer to Figure 1.
TYPICAL CHARACTERISTIC CURVES
3.030
3.025
3.020
3.015
3.010
3.005
3.000
2.995
2.990
2.985
2.980
2.975
2.970
3.05
3.04
3.03
3.02
3.01
3
2.99
2.98
2.97
2.96
2.95
-75
-50
-25
0
25
50
75
100
125
TEMPERATURE [°C]
5.0
6.0
7.0
8.0
9.0 10.0 11.0 12.0 13.0 14.0 15.0
VDD [V]
Figure 1. Reference vs. VDD
Figure 2. Reference vs. Temperature
4
UCC1829-1/-2/-3
UCC2829-1/-2/-3
UCC3829-1/-2/-3
PIN DESCRIPTIONS
phase. The UCC3829 -3 implements OUTA and OUTB
to be non-overlapping complementary outputs during the
same clock cycle. The output frequency of the
BISYNC: Combination clock output/sync input pin. The
clock signal can be viewed on this pin. If BISYNC is con-
nected to BISYNC of other UCC3829 chips, all the oscil-
lators will run at the highest of all the chips frequencies.
The BISYNC pin has a weak pull down and a strong pull
up.
UCC3829-1 is half that of the UCC3829-2
UCC3829 -3.
and
PGND: Power ground return. The PGND pin should be
used as the return for the VDD bypass capacitor and the
current sense kelvin CL-.
CL+: Current sense input for current limiting. The CL+
and CL- pins are used for current sensing. CL+ is the
current signal while CL- is the kelvin return for the sens-
ing function.
PWCONT: Pulse width control input. This is connected to
the PWM comparator inverting input.
CL–: Current sense input kelvin common.
RAMP: Ramp input . This is connected to the PWM com-
parator non-inverting input through a level shifting volt-
age of approximately 1.25V.
CT: Oscillator timing capacitor. A capacitor connected
between CT and GND is charged by a current source
controlled by RT1. The capacitor is discharged through a
resistor connected between CT and RT2.
RT1: Oscillator charging current programming resistor. A
1V reference at this pin generates a current through a re-
sistor connected between RT1 and GND. This current is
mirrored and ratioed to charge the timing capacitor con-
nected to pin CT.
EAOUT: Error amplifier output. This output is normally
connected directly to the PWCONT pin. It can also be
connected to PWCONT through a resistor divider at-
tenuation network to allow more swing of the error ampli-
fier output. A maximum capacitive load of 20pF with
respect to ground must be observed to insure stability of
the error amplifier.
RT2: Oscillator discharge time programming resistor. The
oscillator (and output) dead time can be programmed via
this pin. The discharge of the timing capacitor CT is de-
termined by an RC discharge using a resistor connected
between RT2 and CT.
GND: Logic and analog ground. The GND pin should be
used for all signal level returns, except the current sense
inputs.
SS: Soft start capacitor pin. A capacitor connected to SS
determines the time the IC takes to soft start. The nomi-
nal SS pin pull up and pull down current is 20µA. The soft
start time delay is approximately calculated as:
INV: Error amplifier inverting input.
LEB: Leading edge blanking programming pin. Connect-
ing a resistor between VREF and LEB and a capacitor
between LEB and GND will program a leading edge
blanking time according to the RC of the resistor/capaci-
tor combination. Connecting the LEB pin to VDD disables
the Leading Edge Blanking function.
CSS • 3V
20 µA
when charging from 0V. After the SS pin reaches the SS
complete threshold of 3V, another SS cycle can be
started. The restart time is approximately:
NINV: Error amplifier non-inverting input.
2 • CSS • 3V
OUTA: Output A. The OUTA pin will pull down with ap-
proximately 1.5A and pull up with approximately 0.75A.
The UCC3829-1 implements push-pull outputs with
OUTA and OUTB active on alternating clock cycles. The
UCC3829-2 implements OUTA and OUTB being in
phase. The UCC3829 -3 implements OUTA and OUTB to
be non-overlapping complementary outputs during the
same clock cycle. The output frequency of the
20 µA
UVLO: Undervoltage lockout programming pin. Connect-
ing a resistor divider between VDD, UVLO, and GND
sets a VDD value at which the UCC3829 chip will be en-
abled. When the voltage on the UVLO pin reaches 3V,
the chip is enabled. When the voltage on UVLO falls be-
low 2.5V, the chip is disabled.
UCC3829-1 is half that of the UCC3829-2
UCC3829 -3.
and
VDD: Voltage supply to IC. VDD is clamped at 14V.
VREF: Voltage reference output and filtering. The voltage
reference output appears on the VREF pin. It is buffered
to drive approximately 5mA and short circuit protected at
approximately 25mA. A bypass capacitor of at least
0.1µF must be connected from VREF to ground.
OUTB: Output B. The OUTB pin will pull down with ap-
proximately 1.5A and pull up with approximately 0.75A.
The UCC3829-1 implements push-pull outputs with
OUTA and OUTB active on alternating clock cycles. The
UCC3829-2 implements OUTA and OUTB being in
5
UCC1829-1/-2/-3
UCC2829-1/-2/-3
UCC3829-1/-2/-3
APPLICATION INFORMATION
Functional Programmability
The approximate equation for the falling edge (TF) of the
CT waveform (deadtime period) is:
9.3RT 2
Various features of the UCC3829 are user programma-
ble. RT1 and RT2 allow independent programming for
oscillator rise and fall times within the normal operational
range of the chip. A new feature allows the user to pro-
gram the voltage that flags an undervoltage fault. The
default value of 14V for chip turn-on is selected by tying
the UVLO pin to ground. If the user wants to select
startup voltage then a resistive divider should be tied
from Vdd to ground, with the centerpoint tied to the
UVLO pin. The chip will be enabled when the UVLO pin
reaches 3V, and disabled below 2.5V. Leading edge
blanking can also be optimized to eliminate turn-on noise
when current mode control is used or disabled when de-
sired.
V
PEAK
–
RT 1
T
F
=RT 2
C ln=
T
9.3RT 2
VVALLEY
–
RT 1
Assuming that:
9.3R
9.3R
T 2 <<VPEAK and
T 2 <<VVALLEY
RT 1
RT 1
We get a simplified equation:
V
PEAK
TF
=RT 2C ln
T
V
VALLEY
Given a maximum on-time and frequency and assuming
an initial value for either RT2 or CT, you can use the TF
equation to calculate the other. Once you have a value
for CT, you can calculate RT1 using the TR equation.
Oscillator
The oscillator uses an external capacitor CT and two ex-
ternal resistors RT1 and RT2 to generate the clock fre-
quency and dead time. A precise reference voltage is
placed across resistor RT1 to generate a current refer-
ence. The current is then mirrored and used to charge
the capacitor CT from VVALLEY. When a “peak” threshold
is reached, an on chip MOSFET connects the RT2 pin to
GND, discharging CT to a “valley” threshold through an
external resistor RT2. The CT waveform has a linear
ramp shape while charging and an exponential (RC)
slope while discharging. The slope of the charging ramp
is set by the CT, RT1 combination and the slope of the
discharging ramp is set by the values of CT and RT2.
Error Amplifier Section
The Error Amplifier has both inputs and the output
brought out to pins NINV, INV, and EAOUT. The output of
the error amplifier can be connected to the inverting input
of the PWM comparator via the pin PWCONT. This al-
lows inserting attenuation which enables using the full
output swing of the error amplifier. The output of the error
amplifier is forced to follow the soft start waveform during
soft start.
PWM and Output Section
The non-inverted input of the PWM comparator is con-
nected to RAMP. The RAMP can be connected to either
the CT capacitor for voltage mode control, to the current
sense resistor for current mode control, or to a feed for-
ward capacitor for input voltage feed forward control. The
CT waveform can be coupled to RAMP to provide slope
compensation in the current mode case. The MOSFET
switch connected to RAMP provides for the discharge of
the feedforward capacitor. There is a short time constant
(3ns) filter across the inputs of the PWM comparator to
reduce noise.
The approximate equation for the rising edge (TR) of the
CT waveform (maximum on-time period) is:
V
PEAK –
V
VALLEY
TR
=CTRT 1
9.3
The output of the PWM comparator feeds an OR gate
which, together with several other fault signals, sets the
PWM latch. The latch is in turn reset on every dead time
period of the clock waveform. The output of the PWM
latch is OR’ed with the clock and the output of the Fault
Latch (described below) to feed into the pulse steering
Toggle Flip-Flop (TFF). The resulting signal is then
steered according to the output configuration of
UCC3829. The clock output becomes the deadtime be-
tween the outputs.
UDG-97016
Figure 3.
6
UCC1829-1/-2/-3
UCC2829-1/-2/-3
UCC3829-1/-2/-3
Output Timing Configurations
Leading Edge Blanking Section
The timing diagram shows the major differences between The Leading Edge Blanking circuit provides a means to
the UCC3829-1, -2 and -3 parts. The output of the insert a blanking period at the beginning of the cycle,
UCC3829-1 is a push-pull configuration with outputs A providing noise pulse elimination for current mode control
and B 180° out of phase and with an output frequency
that is half of the CT’s waveform.
applications. This feature is similar to that of the UC3825
and UC3823A/B controllers. When enabled, an external
resistor is connected from LEB to VREF. An external ca-
pacitor is connected from LEB to either VREF or GND.
During the deadtime, LEB is pulled to GND. At the begin-
ning of the cycle, the pin is released and the capacitor
charges through the resistor toward VREF. At the thresh-
old VREF/2, a comparator senses the voltage and LEB is
removed. The leading edge blanking function can be dis-
abled by connecting LEB to VDD (> VREF). Leading
edge blanking is performed by the same MOSFET switch
connected to RAMP that is used for voltage feed forward
operation.
The UCC3829-2 produces dual outputs that are in phase
and can be used in situations that require high current
drive for single ended designs. A 0.5 resistor should be
added in series with each output before they are con-
nected together. The output pulse frequency is equal to
the CT waveform frequency in this case.
The output drive in the UCC3829-3 has a non-
overlapping complementary configuration. During each
clock cycle Output A produces an output pulse, followed
by a short delay, and then Output B produces an output
pulse. The short delay between Output A and Output B
pulses is tcd, the complementary delay time. This en-
sures that the outputs are never high simultaneously.
Current Timing and Protection
The current limit and overcurrent functions are accom-
plished using the pins CL+ and CL–. These two pins pro-
vide for differential current level sensing, with the trip
points referenced to CL–, rather than GND. The current
limit function provides a pulse by pulse current limiting,
whereas the overcurrent function is considered a fault
condition and initiates a fault logic soft start cycle.
TIMING DIAGRAMS
PWM CNTL
CT
The UCC3829 utilizes differential current sensing and
separate logic and power ground pins to eliminate some
of the noise issues of using current mode control. De-
vices with only one common ground pin for all stated
functions required the combination of power gate drive
current and low-level sensing currents in a common
trace. Since the current signal needed for control is em-
bedded in the power gate drive current, it is not enough
just to separate logic and power ground pins. Differential
sensing in UCC3829 referenced to the negative rail al-
lows the cleanest method of sensing current for use in a
peak current mode controlled power supply utilizing re-
sistive sensing. Current limiting is done on a cycle by cy-
cle basis when the typical threshold of 0.875V is
reached. If the fault level of 1.25V is reached a soft start
cycle is initiated. Internal circuitry insures that soft start
cycles are completed so that fault currents can be con-
trolled.
BISYNC
UCC1829-1
OUT A
UCC1829-1
OUT B
UCC1829-2
OUT A
UCC1829-2
OUT B
Fault Logic Section
UCC1829-3
OUT A
The fault logic detects and handles various fault condi-
tions in the system. The output of the overcurrent com-
parator is logically ORed with the output combination of
the undervoltage detection circuit ORed with the output
of the VREF good circuit. The output of the precision ref-
erence voltage VREF is compared to a level (approxi-
UCC 1829-3
OUT B
tr
tf
tcd
7
UCC1829-1/-2/-3
UCC2829-1/-2/-3
UCC3829-1/-2/-3
mately 3 VBE voltages) to determine if the reference is
alive. The undervoltage circuit either uses a user pro-
grammed level with a 16% hysteresis or an on threshold
equal to the VDD clamp voltage and an off threshold of
9V.
sink and turns on a 20µA current source to charge the SS
capacitor.
The under voltage detection is set to a default value of
14V turn on (VDD clamp active value) and 9V turn off
when the UVLO pin is tied to GND. This default configu-
ration can be overridden by connecting a resistor divider
between VDD and GND to the UVLO pin. The hysteresis
Once a fault occurs, a soft start cycle takes place. A fault
sets the fault latch. The Q output of the fault latch sets
the RS delay latch and turns on the 20µA soft start dis- for the user set threshold is 16%.
charge current sink. The Q output of the fault latch is
During undervoltage lockout, the self biasing outputs are
gated, however, by the output of the SS complete com-
parator. This insures that a SS cycle cannot start before
the previous one has finished. The soft start capacitor
then is discharged to 1V which is sensed by the RS delay
comparator. The fault latch is then reset. This in turn re-
sets the RS delay latch and turns off the 20µA current
held "OFF" to prevent accidental turn-on of the power
switches.
Supply Section
The incoming voltage supply VDD is clamped by a shunt
VDD Clamp circuit at 14V.
TYPICAL APPLICATIONS
VIN
DC SOURCE
OR RECTIFIED AC
VOUT
BIAS
SUPPLY
ISOLATED
FEEDBACK
UCC3829-1
UDG-98013
Figure 4. Push-Pull Converter Using UCC3829-1
8
UCC1829-1/-2/-3
UCC2829-1/-2/-3
UCC3829-1/-2/-3
TYPICAL APPLICATIONS (cont.)
VIN
VOUT
UDG-98014
Figure 5. Single Ended Converter with High Power Gate Drive Using UCC3829-2
P/O CT1
VIN
VOUT
VDD SUPPLY
P/O CT1
UCC3829-3
COMMON
UDG-98015
Figure 6. Synchronous Rectifier Controller Using UCC3829-3
For additional information, please see U-128 that details
operation and application of some of the features of
UC3823A,B and UC3825A,B PWM Controllers.
UNITRODE CORPORATION
7 CONTINENTAL BLVD. • MERRIMACK, NH 03054
TEL. (603) 424-2410 • FAX (603) 424-3460
9
PACKAGE OPTION ADDENDUM
www.ti.com
30-Mar-2005
PACKAGING INFORMATION
Orderable Device
Status (1)
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
SOIC
SOIC
Drawing
UCC3829DW-1
UCC3829DW-2
UCC3829DW-3
UCC3829DWTR-1
UCC3829DWTR-2
UCC3829N-1
OBSOLETE
OBSOLETE
OBSOLETE
OBSOLETE
OBSOLETE
OBSOLETE
OBSOLETE
OBSOLETE
OBSOLETE
OBSOLETE
OBSOLETE
DW
20
20
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
TBD
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
DW
UTR
DW
SOIC
SOIC
PDIP
PDIP
20
20
20
20
DW
N
UCC3829N-2
N
UCC3829N-3
UTR
UTR
UTR
UTR
UCC3829Q-1
UCC3829Q-2
UCC3829Q-3
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan
-
The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS
&
no Sb/Br)
-
please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Audio
Amplifiers
amplifier.ti.com
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
Digital Control
Military
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/military
Interface
Logic
interface.ti.com
logic.ti.com
Power Mgmt
Microcontrollers
power.ti.com
Optical Networking
Security
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
microcontroller.ti.com
Telephony
Video & Imaging
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright 2005, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明