UCC3921J [TI]
1-CHANNEL POWER SUPPLY MANAGEMENT CKT, CDIP8;型号: | UCC3921J |
厂家: | TEXAS INSTRUMENTS |
描述: | 1-CHANNEL POWER SUPPLY MANAGEMENT CKT, CDIP8 CD 信息通信管理 |
文件: | 总16页 (文件大小:1103K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
UCC1921
UCC2921
UCC3921
Latchable Negative Floating Hot Swap Power Manager
FEATURES
DESCRIPTION
• Precision Fault Threshold
The UCC3921 family of negative floating hot swap power managers pro-
vides complete power management, hot swap, and fault handling capa-
bility. The IC is referenced to the negative input voltage and is powered
through an external resistor connected to ground, which is essentially a
current drive as opposed to the traditional voltage drive. The onboard
10V shunt regulator protects the IC from excess voltage and serves as a
reference for programming the maximum allowable output sourcing cur-
rent during a fault. All control and housekeeping functions are integrated
and externally programmable. These include the fault current level, maxi-
mum output sourcing current, maximum fault time, selection of Retry or
Latched mode, soft start time, and average power limiting. In the event of
a constant fault, the internal timer will limit the on time from less than
0.1% to a maximum of 3% duty cycle. The duty cycle modulation de-
pends on the current into PL, which is a function of the voltage across
the FET, thus limiting average power dissipation in the FET. The fault
level is fixed at 50mV across the current sense amplifier to minimize total
• Programmable:
Average Power Limiting, Linear
Current Control, Overcurrent Limit
and Fault Time
• Fault Output Indication Signal
• Automatic Retry Mode or Latched
Operation Mode
• Shutdown Control
• Undervoltage Lockout
• 250µs Glitch Filter on the SDFLTCH
pin
• 8-Pin DIL and SOIC
(continued)
BLOCK DIAGRAM
UDG-99052
3/98
UCC1921
UCC2921
UCC3921
DESCRIPTION (continued)
dropout. The fault current level is set with an external
current sense resistor, while the maximum allowable
sourcing current is programmed with a voltage divider
from VDD to generate a fixed voltage on IMAX. The cur-
rent level, when the output acts as a current source, is
equal to VIMAX/RSENSE. If desired, a controlled current
start up can be programmed with a capacitor on IMAX.
CT charges to 2.5V, the output device is turned off and
performs a retry some time later (provided that the se-
lected mode of operation is Automatic Retry Mode).
When the output current reaches the maximum sourcing
current level, the output acts as a current source, limiting
the output current to the set value defined by IMAX.
Other features of the UCC3921 include undervoltage
lockout, 8-pin Small Outline (SOIC) and Dual-In-Line
(DIL) packages, and a Latched Operation Mode option,
in which the output is latched off once CT charges to
2.5V and stays off until either SDFLTCH is toggled (for
greater than 1ms) or the IC is powered down and then
back up.
When the output current is below the fault level, the out-
put device is switched on. When the output current ex-
ceeds the fault level, but is less than the maximum
sourcing level programmed by IMAX, the output remains
switched on, and the fault timer starts charging CT. Once
CONNECTION DIAGRAM
ABSOLUTE MAXIMUM RATINGS
IVDD. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50mA
SDFLTCH Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10mA
PL Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10mA
IMAX Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VDD
Storage Temperature . . . . . . . . . . . . . . . . . . . −65°C to +150°C
Junction Temperature. . . . . . . . . . . . . . . . . . . –55°C to +150°C
Lead Temperature (Soldering, 10 sec.) . . . . . . . . . . . . . +300°C
DIL-8 , SOIC-8 (Top View)
N or J, D Packages
All voltages are with respect to VSS (the most negative voltage).
Currents are positive into, negative out of the specified terminal.
Consult Packaging Section of Databook for thermal limitations and
considerations of packages.
ELECTRICAL CHARACTERISTICS Unless otherwise specified, TA = 0°C to 70°C for the UCC3921 and –40°C to 85°C
for the UCC2921, and –55°C to 125°C for the UCC1921; IVDD = 2mA, CT = 1nF (the minimum allowable value), there is no
resistor connected between the SDFLTCH and VSS pins. TA = TJ.
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNITS
VDD Section
IDD
1
2
10.0
10.15
8
mA
V
Regulator Voltage
ISOURCE = 2mA
ISOURCE = 10mA
9
9.15
6
9.5
9.6
7
V
UVLO Off Voltage
Fault Timing Section
Overcurrent Threshold
V
TJ = 25°C
47.5
46
50
50
53.5
53.5
500
–22
–0.7
1.5
mV
mV
nA
µA
mA
µA
V
Over Operating Temperature
Overcurrent Input Bias
CT Charge Current
50
VCT = 1V, IPL = 0
–50
–1.7
0.6
–36
–1.2
1
Overload Condition, VSENSE - VIMAX = 300mV
VCT = 1V, IPL = 0
CT Discharge Current
CT Fault Threshold
CT Reset Threshold
Output Duty Cycle
2.2
2.45
0.49
2.7
2.6
0.41
1.7
0.57
3.7
V
Fault Condition, IPL = 0
%
2
UCC1921
UCC2921
UCC3921
ELECTRICAL CHARACTERISTICS Unless otherwise specified, TA = 0°C to 70°C for the UCC3921 and –40°C to 85°C
for the UCC2921, and –55°C to 125°C for the UCC1921; IVDD = 2mA, CT = 1nF (the minimum allowable value), there is no
resistor connected between the SDFLTCH and VSS pins. TA = TJ.
PARAMETER
Output Section
TEST CONDITIONS
MIN
TYP
MAX UNITS
Output High Voltage
IOUT = 0mA
8.5
6
10
8
V
V
IOUT = –1mA
Output Low Voltage
IOUT = 0mA, VSENSE – VIMAX = 100mV
IOUT = 2mA, VSENSE – VIMAX = 100mV
0
10
mV
mV
200
600
Linear Amplifier Section
Sense Control Voltage
VIMAX = 100mV
VIMAX = 400mV
85
100
400
50
115
430
500
mV
mV
nA
370
Input Bias
Power Limiting Section
VSENSE Regulator Voltage
Duty Cycle Control
IPL = 64µA
IPL = 64µA
IPL = 1mA
4.35
0.6
4.85
1.2
5.35
1.7
V
%
%
0.045
0.1
0.17
Overload Section
Delay to Output
Note 1
300
100
200
500
260
ns
Output Sink Current
Threshold
VSENSE – VIMAX = 300mV
Relative to IMAX
40
mA
mV
140
Shutdown/Fault/Latch Section
Shutdown Threshold
Input Current
3
50
250
6
5
VDD+1
250
V
µA
µs
V
VSDFLTCH = 5V
110
500
9.5
8.5
0
Filter Delay Time (Delay to Output)
Fault Output High
1000
ISDFLTCH = –100µA
5
V
Fault Output Low
Output Duty Cycle
10
3.7
0
mV
%
Fault Condition, IPL = 0
1.7
2.7
ISDFLTCH = –100µA, Fault Condition, IPL = 0
%
Note 1: Guaranteed by design. Not 100% tested in production.
PIN DESCRIPTIONS
voltage on IMAX over the current sense resistor. If
desired, a controlled current start up can be programmed
with a capacitor on IMAX, and a programmed start delay
can be achieved by driving the shutdown with an open
collector/drain device into an RC network.
CT: A capacitor is connected to this pin in order to set
the fault time. The fault time must be longer than the time
to charge external load capacitance. The fault time is
defined as:
• C
T
=
OUT: This pin provides gate output drive to the MOSFET
I
pass element.
where ICH = 36µA + IPL, and IPL is the current into the
power limit pin. Once the maximum fault time is reached
the output will shutdown for a time given by:
PL: This feature ensures that the average MOSFET
power dissipation is controlled. A resistor is connected
from this pin to the drain of the NMOS pass element.
When the voltage across the NMOS exceeds 5V, current
will flow into the PL pin which adds to the fault timer
charge current, reducing the duty cycle from the 3%
T
=
•
• C
IMAX: This pin programs the maximum allowable
sourcing current. Since VDD is a regulated voltage, a
voltage divider can be derived from VDD to generate the
program level for IMAX. The current level at which the
output appears as a current source is equal to the
level. When I >>36µA, then the average MOSFET
PL
power dissipation is given by:
−
P
avg =IMAX • •
• R
3
UCC1921
UCC2921
UCC3921
PIN DESCRIPTIONS (continued)
SENSE: Input voltage from the current sense resistor.
If an 5k < R
< 250kΩ resistor is placed from this pin
LATCH
When there is greater than 50mV across this pin with
to VSS, then the latched operating mode will be invoked.
Upon the occurrence of a fault, under the latched mode
respect to VSS, then a fault is sensed, and C starts to
T
charge.
of operation, once the C capacitor charges up to 2.5V
T
the NMOS pass element latches off. A retry will not
periodically occur. To reset the latched off device, either
SDFLTCH is toggled high for a duration greater than 1ms
or the IC is powered down and then up.
SDFLTCH: This pin provides fault output indication,
shutdown control, and operating mode selection.
Interface into and out of this pin is usually performed
through level shift transistors. When open, and under a
non-fault condition, this pin pulls to a low state with
respect to VSS. When a fault is detected by the fault
timer, or undervoltage lockout, this pin will drive to a high
state with respect fo VSS, indicating the NMOS pass
element is OFF. When > 250µA is sourced into this pin
for > 1ms, it drives high causing the output to disable the
NMOS pass device.
VDD: Current driven with a resistor to a voltage approxi-
mately 10V more positive than VSS. Typically a resistor is
connected to ground. The 10V shunt regulator clamps
VDD approximately 10V above VSS, and is also used as
an output reference to program the maximum allowable
sourcing current.
VSS: Ground reference for the IC and the most negative
voltage available.
APPLICATION INFORMATION
UDG-96275-1
Figure 1. Fault Timing Circuitry for the UCC3921, Including Power Limit Overload
4
UCC1921
UCC2921
UCC3921
APPLICATION INFORMATION (continued)
Figure 1 shows the detailed circuitry for the fault timing is related to the voltage across the FET with the following
function of the UCC3921. For the time being, we will dis- expression:
cuss a typical fault mode, therefore, the overload com-
V
− V
I
=
parator, and current source I3 does not work into the
operation. Once the voltage across the current sense re-
sistor, RS, exceeds 50mV, a fault has occurred. This
causes the timing capacitor to charge with a combination
of 36µA plus the current from the power limiting amplifier.
The PL amplifier is designed to only source current into
the CT pin and to begin sourcing current once the volt-
R
where V
is the voltage across the NMOS pass device.
FET
Later it will be shown how this feature will limit average
power dissipation in the pass device. Note that under a
condition where the output current is more than the fault
level, but less than the max level, V
≈ VSS (input
OUT
age across the output FET exceeds 5V. The current I
voltage), I = 0, the CT charging current is 36µA.
PL
PL
UDG-96276
t0: Safe condition. Output current is nominal, output t5 = t3: Illustrates 3% duty cycle.
voltage is at the negative rail, VSS.
t6 = t4: Retry. CT has discharged to 0.5V, but fault is
t1: Fault control reached. Output current rises above still exceeded, CT begins charging again, FET is on,
the programmed fault value, CT begins to charge at
V
OUT
pulled down towards VSS.
~36µA.
t7: Output short circuit. If VOUT is short circuited to
ground, CT charges at a higher rate depending upon
t2: Maximum current reached. Output current reaches
the values for VSS and R
.
PL
the programmed maximum level and becomes a con-
stant current with value I
.
MAX
t8: Fault occurs. Output is still short circuited, but the
occurrence of a fault turns the FET off so no current is
conducted.
t3: Fault occurs. CT has charged to 2.5V, fault output
goes high, the FET turns off allowing no output current
to flow, V
floats up to ground.
OUT
t9 = t4: Output short circuit released, still in fault mode.
t4: Retry. CT has discharged to 0.5V, but fault current is
still exceeded, CT begins charging again, FET is on,
t10 = t0: Fault released, safe condition. Return to nor-
mal operation of the hot swap power manager.
V
pulled down towards VSS.
OUT
Figure 2. Retry Operation Mode
5
UCC1921
UCC2921
UCC3921
APPLICATION INFORMATION (cont.)
UDG-96277
is still exceeded, CT begins charging again, FET is on,
t0: Safe condition. Output current is nominal, output
V
OUT
pulled down towards VSS.
voltage is at the negative rail, VSS.
t8 = t3: Fault occurs. CT has charged to 2.5V, fault out-
put goes high as indicated by the SDFLTCH voltage,
the FET turns off allowing no output current to flow,
t1: Fault control reached. Output current rises above
the programmed fault value, CT begins to charge at
~36µA.
V
floats up to ground, and since there is an 82kΩ
OUT
t2: Maximum current reached. Output current reaches
the programmed maximum level and becomes a con-
resistor from SDFLTCH to VSS, the internal latchset
signal goes high.
stant current with value I
.
MAX
t9: Output is latched off. Even though CT has dis-
charged to 0.5V, there will not be a retry since the
latchset signal was allowed to remain high.
t3: Fault occurs. CT has charged to 2.5V, fault output
goes high as indicated by the SDFLTCH voltage. The
FET turns off allowing no output current to flow, V
OUT
t10: Output remains latched off. CT has discharged all
the way to 0V.
floats up to ground, and since there is an 82kΩ resistor
from the SDFLTCH pin to VSS, the internal latchset sig-
nal goes high.
t11: The output has been latched off for quite some
time. The user now wishes to reset the latched off out-
put, thus toggling SDFLTCH high for greater than 1ms
{t13 - t11}.
t4: Since the user does not want the chip to LATCH off
during this cycle, he toggles SDFLTCH high for greater
than 1ms {t6 - t4 > 1ms}.
t12 = t5: The latchset signal is reset.
t5: The latchset signal is reset.
t13: Forcing of SDFLTCH is released after having been
applied for > 1ms. The fault had also been released
during the time the output was latched off, safe condi-
tion, return to normal operation of the hot swap power
manager.
t6: Forcing of SDFLTCH is released after having been
applied for > 1ms.
t7: Retry (since the latchset signal has been reset to its’
low state) - CT has discharged to 0.5V, but fault current
Figure 3. Latched Operation Mode: RLATCH = 82k
6
UCC1921
UCC2921
UCC3921
APPLICATION INFORMATION (continued)
During a fault, CT will charge at a rate determined by the output FET failure or to build redundancy into the sys-
internal charging current and the external timing capaci- tem.
tor. Once CT charges to 2.5V, the fault comparator
switches and sets the fault latch. Setting of the fault latch
Determining External Component Values
To set R
(see Fig. 4) the following must be achieved:
VDD
causes both the output to switch off and the charging
switch to open. CT must now discharge with the 1µA cur-
rent source, I2, until 0.5V is reached. Once the voltage at
CT reaches 0.5V, the fault latch resets, which re-enables
the output and allows the fault circuitry to regain control
of the charging switch. If a fault is still present, the fault
comparator will close the charging switch causing the cy-
cle to repeat. Under a constant fault, the duty cycle is
given by:
V
R
V
>
+ mA
R + R
µA
Duty Cycle =
I
+
µA
Average power dissipation in the pass element is given
by:
µA
P
=V
• I
•
UDG-96278
I
+
µA
Figure 4.
Where V
>>5V I can be approximated as:
FET
PL
V
R
In order to estimate the minimum timing capacitor, C ,
T
several things must be taken into account. For example,
given the schematic in Figure 4 as a possible (and at this
point, a standard) application, certain external compo-
and where I >>36µA, the duty cycle can be approxi-
PL
mated as :
µA • R
V
nent values must be known in order to estimate C
.
TMIN
Now, given the values of C
, Load, R
, V , and
SENSE SS
OUT
the resistors determining the voltage on the IMAX pin,
the user can calculate the approximate startup time of
Therefore, the maximum average power dissipation in
the MOSFET can be approximated by:
the node V
This startup time must be faster than the
OUT.
time it takes for C to charge to 2.5V (relative to V ),
T
SS
µA • R
and is the basis for estimating the minimum value of C .
T
P
=V
• I
•
V
In order to determine the value of the sense resistor,
R
, assuming the user has determined the fault cur-
SENSE
=IMAX • µA • R
rent, R
can be calculated by:
SENSE
Notice that in the approximation, V
limiting the average power dissipation in the NMOS pass
element.
cancels, thereby
FET
mV
I
R
=
Next, the variable I
must be calculated. I
is the
MAX
MAX
Overload Comparator
maximum current that the UCC3921 will allow through
the transistor, M1, and it can be shown that during
startup with an output capacitor the power MOSFET, M1,
can be modeled as a constant current source of value
The linear amplifier in the UCC3921 ensures that the
output NMOS does not pass more than I
(which is
MAX
V
R
). In the event the output current exceeds
IMAX/ SENSE
the programmed I
by 0.2V/R
which can only
MAX
SENSE,
I
where
MAX
occur if the output FET is not responding to a command
from the IC, CT will begin charging with I3, 1mA, and
continue to charge to approximately 8V. This allows a
constant fault to show up on the SDFLTCH pin, and also
since the voltage on CT will continue charging past 2.5V
in an overload fault mode, it can be used for detection of
V
I
=
where V
= voltage on pin IMAX.
IMAX
R
Given this information, calculation of the startup time is
now possible via the following:
7
UCC1921
UCC2921
UCC3921
APPLICATION INFORMATION (continued)
Current Source Load:
Resistive Load:
C
=
C
• V
−I
T
=
• T
•
µA • R + V
− V −I
• R
(
)
I
• R
Resistive Load:
• R
• V
• R
• C
T
=
+
I
• R
C
• R
•
ln
Level Shift Circuitry to Interface with SDFLTCH
I
• R
− V
Some type of circuit is needed to interface with the
UCC3921 via SDFLTCH, such as opto-couplers or level
shift circuitry. Figure 6 depicts one implementation of
level shift circuitry that could be used, showing compo-
nent values selected for a typical –48V telecommunica-
tions application. There are three communication
conditions which could occur; two of which are Hot Swap
Power Manager (HSPM) state output indications, and the
third being an External Shutdown.
Once T
is calculated, the power limit feature of the
START
UCC3921 must be addressed and component values de-
rived. Assuming the user chooses to limit the maximum
25
22.5
RPL=∞
IMAX =4A
20
17.5
15
1) When open, and under
a non-fault condition,
SDFLTCH is pulled to a low state. In Figure 6, the N-
channel level shift transistor is off, and the
FAULT OUT signal is pulled to LOCAL VDD through
R3. This indicates that the HSPM is not faulted.
RPL = 10M
RPL = 5M
12.5
10
2) When a fault is detected by the fault timer or under-
voltage lockout, this pin will drive to a high state, indi-
cating that the external power FET is off. In Figure 6,
the N-channel level shift transistor will conduct, and
the FAULT OUT signal will be pulled to a Schottky Di-
ode voltage drop below LOCAL GND. This indicates
that the HSPM is faulted. The Schottky Diode is nec-
essary to ensure that the FAULT OUT signal does
not traverse too far below LOCAL GND, making fault
detection difficult.
7.5
RPL = 2M
RPL = 1M
5
2.5
0
RPL = 500k
RPL = 200k
0
25 50 75 100 125 150 175 200
VFET
Figure 5. Plot Average Power vs FET Voltage for
Increasing Values of RPL
allowable average power that will be associated with the
hot swap power manager, the power limiting resistor,
RPL, can be easily determined by the following:
P
avg
R
=
where a minimum R exists
PL
µA • I
V
defined by R
=
(Refer to Figure 5).
mA
Finally, after computing the aforementioned variables, the
minimum timing capacitor can be derived as such:
Current Source Load:
UDG-96279
C
=
Figure 6. Possible Level Shift Circuitry to
Interface to the UCC3921, showing component
values selected for a typical telecom application.
• T
•
µA • R + V
• R
−
V
(
)
8
UCC1921
UCC2921
UCC3921
APPLICATION INFORMATION (continued)
limited to 10mA or less: ISDFLTCHMAX < 10mA.
If a 5k < R
< 250kΩ resistor is tied between
LATCH
SDFLTCH & VSS, as optionally shown in Figure 6,
then the latched operating mode (described earlier)
will be invoked upon the occurrence of a fault.
SAFETY RECOMMENDATIONS
Although the UCC3921 is designed to provide system
protection for all fault conditions, all integrated circuits
can ultimately fail short. For this reason, if the UCC3921
is intended for use in safety critical applications where
UL or some other safety rating is required, a redundant
safety device such as a fuse should be placed in series
with the external power FET. The UCC3921 will prevent
the fuse from blowing for virtually all fault conditions, in-
creasing system reliability and reducing maintenance
cost, in addition to providing the hot swap benefits of the
device.
3) To externally shutdown the HSPM, the SHUTDOWN
signal (typically held at LOCAL VDD) must be pulled
to LOCAL GND. Assuming SHUTDOWN is tied to
LOCAL GND, the P-channel level shift transistor will
conduct, driving SDFLTCH high (to roughly VDD plus
a diode). By sourcing > 250µA into SDFLTCH for >
1ms the output to the external power FET will be dis-
abled. The current sourced into SDFLTCH must be
Ω
UDG-98053
Figure 7. Typical Telecommuications Application
(The “Negative Magnitude-Side” of the Supply is Switched in)
9
UCC1921
UCC2921
UCC3921
APPLICATION INFORMATION (continued)
Ω
UDG-98054
Figure 8. Floating Positive Application
The “Ground-side” of the Supply is Switched In
UNITRODE CORPORATION
7 CONTINENTAL BLVD. • MERRIMACK, NH 03054
TEL. (603) 424-2410 • FAX (603) 424-3460
10
PACKAGE OPTION ADDENDUM
www.ti.com
26-Aug-2013
PACKAGING INFORMATION
Orderable Device
UCC2921D
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 85
-40 to 85
-40 to 85
-40 to 85
0 to 70
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
ACTIVE
SOIC
SOIC
SOIC
SOIC
SOIC
D
8
8
8
8
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-1-260C-UNLIM
UCC2921
UCC2921DG4
UCC2921DTR
UCC2921DTRG4
UCC3921D
ACTIVE
ACTIVE
ACTIVE
ACTIVE
D
D
D
D
75
2500
2500
75
Green (RoHS
& no Sb/Br)
UCC2921
UCC2921
UCC2921
UCC3921
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
UCC3921D/81143G4
UCC3921DG4
OBSOLETE
ACTIVE
SOIC
SOIC
D
D
8
8
TBD
Call TI
Call TI
UCC3921
UCC3921
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-1-260C-UNLIM
0 to 70
0 to 70
UCC3921DTR
UCC3921DTR/81143
UCC3921DTR/81143G4
UCC3921DTRG4
ACTIVE
ACTIVE
ACTIVE
ACTIVE
SOIC
SOIC
SOIC
SOIC
D
D
D
D
8
8
8
8
2500
2500
2500
2500
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
Level-1-260C-UNLIM
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-1-260C-UNLIM
UCC3921
UCC3921
UCC3921
UCC3921
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
0 to 70
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
26-Aug-2013
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
31-Dec-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
UCC2921DTR
UCC3921DTR
SOIC
SOIC
SOIC
D
D
D
8
8
8
2500
2500
2500
330.0
330.0
330.0
12.4
12.4
12.4
6.4
6.4
6.4
5.2
5.2
5.2
2.1
2.1
2.1
8.0
8.0
8.0
12.0
12.0
12.0
Q1
Q1
Q1
UCC3921DTR/81143
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
31-Dec-2012
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
UCC2921DTR
UCC3921DTR
SOIC
SOIC
SOIC
D
D
D
8
8
8
2500
2500
2500
367.0
367.0
367.0
367.0
367.0
367.0
35.0
35.0
35.0
UCC3921DTR/81143
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明