UCC3952-4 [TI]
Enhanced Single Cell Lithium-Ion Battery Protection IC; 增强的单节锂离子电池保护IC型号: | UCC3952-4 |
厂家: | TEXAS INSTRUMENTS |
描述: | Enhanced Single Cell Lithium-Ion Battery Protection IC |
文件: | 总5页 (文件大小:38K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
UCC3952-1/-2/-3/-4
Enhanced Single Cell Lithium-Ion Battery Protection IC
FEATURES
DESCRIPTION
• Protects sensitive Lithium Ion cells
from over-charging and
over-discharging
The UCC3952 is a monolithic BiCMOS lithium-ion battery protection circuit
that is designed to enhance the useful operating life of one cell recharge-
able battery pack. Cell protection features consist of internally trimmed
charge and discharge voltage limits, discharge current limit with a delayed
shutdown and an ultra low current sleep mode state when the cell is dis-
charged. Additional features include an on chip MOSFET for reduced exter-
nal component count and a charge pump for reduced power losses while
charging or discharging a low cell voltage battery pack. This protection cir-
cuit requires one external capacitor and is able to operate and safely shut-
down in the presence of a short circuit condition.
• Dedicated for one cell applications
• Integrated low impedance MOSFET
switch and sense resistor
• Precision trimmed overcharge and
overdischarge voltage limits
• Extremely low power drain
• 3A current capacity
• Overcurrent and Short Circuit
Protection
• Reverse Charger Protection
• Thermal Protection
APPLICATION DIAGRAM
PACK+
1
TCLK
16
15
3k
+
CBPS
2
N/C
0.1µF
3
4
5
6
7
8
BNEG
BNEG
BNEG
BNEG
BNEG
N/C 14
PACK– 13
PACK– 12
PACK– 11
PACK– 10
CHARGER
LOAD
9
BNEG
PACK–
UDG-98205
SLUS400A - FEBRUARY 2000
UCC3952-1/-2/-3/-4
CONNECTION DIAGRAMS
ABSOLUTE MAXIMUM RATINGS
Supply Voltage (PACK+ to BNEG) . . . . . . . . . . . . . . . . . . . . 7V
Maximum Forward Voltage (PACK+ to PACK–) . . . . . . . . . 16V
Maximum Reverse Voltage
SOIC-16 (TOP VIEW)
DP Package
(where PACK+ to BNEG = 5V). . . . . . . . . . . . . . . . . . . . . –8V
Maximum Cell Continuous Charge Current. . . . . . . . . . . . . . 3A
Junction Temperature. . . . . . . . . . . . . . . . . . . . –55°C to 150°C
Storage Temperature Range . . . . . . . . . . . . . . –40°C to 125°C
TCLK
N/C
16 PACK+
15 CBPS
14 N/C
1
2
3
4
5
6
7
8
Currents are positive into, negative out of the specified termi-
nal. Consult Packaging Section of Databook for thermal limita-
tions and considerations of packages. All voltages are
referenced to GND.
N/C
SUB
13 SUB
SUB
12 SUB
BNEG
BNEG
BNEG
11 PACK–
10 PACK–
TSSOP-16 (TOP VIEW)
PW Package
9
PACK–
TCLK
N/C
1
2
3
4
5
6
7
8
16 PACK+
15 CBPS
14 N/C
BNEG
BNEG
BNEG
BNEG
BNEG
BNEG
BCC-18 (TOP VIEW)
GSH Package
PACK–
PACK–
13
12
N/C TCLK
PACK+ N/C
17
11 PACK–
10 PACK–
18
N/C
1
16
2
CBPS 15
N/C 14
9
PACK–
3
4
5
6
BNEG
BNEG
BNEG
BNEG
8
PACK– 13
PACK– 12
PACK– 11
7
10
PACK– PACK–
9
BNEG BNEG
Consult factory for GSH package availability.
ELECTRICAL CHARACTERISTICS: Temperature Range: –20°C < TA < 70°C, Unless otherwise stated. All voltages are
with respect to BNEG. TA = TJ
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNITS
State Transition Threshold Section
NORM to OV (VOV
OV to NORM (VOVR)
NORM to OV (VOV
OV to NORM (VOVR)
NORM to OV (VOV
OV to NORM (VOVR)
NORM to OV (VOV
OV to NORM (VOVR)
)
UCC3952-1
UCC3952-1
UCC3952-2
UCC3952-2
UCC3952-3
UCC3952-3
UCC3952-4
UCC3952-4
4.15
3.85
4.20
3.90
4.25
3.95
4.30
4.00
4.20
3.90
4.25
3.95
4.30
4.00
4.35
4.05
4.25
3.95
4.30
4.00
4.35
4.05
4.40
4.10
V
V
V
V
V
V
V
V
)
)
)
2
UCC3952-1/-2/-3/-4
ELECTRICAL CHARACTERISTICS: Temperature Range: –20°C < TA < 70°C, Unless otherwise stated. All voltages are
with respect to BNEG. TA = TJ
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNITS
State Transition Threshold Section (cont.)
OV Delay Time (TOV
NORM to UV (VUV
)
1
2
sec
V
)
UCC3952-1, UCC3952-2, UCC3952-3,
UCC3952-4
2.25
2.35
2.65
25
2.45
UV to NORM (VUVR)
UCC3952-1, UCC3952-2, UCC3952-3,
UCC3952-4
2.55
10
2.75
40
V
Overdischarge Delay Time (TOD
)
ms
Short Circuit Protection Section
ITHLD
TDLY
Discharge current limit, PACK+ = 3.7V
3.0
1
4.5
2.5
A
Discharge current delay, PACK+ = 3.7V, I = 6A
ms
MΩ
RRESET
Discharge current reset resistance,
PACK+ = 4.0
7.5
Bias Section
IDD
Normal operating current. VUV < VPACK < VOV
Operating current in overvoltage VOV < VPACK
Shutdown operating current VPACK < VUV
5
8
µA
µA
µA
V
11
24
2.5
1.7
VMIN
Minimum cell voltage when all circuits are
guaranteed to be fully functional
FET Switch Section
VPACK
VPACK
RON
–
PACK+ > VOV, I(SWITCH) = 1mA to 2A
Battery overcharged state switch permits
discharge current only.
100
400
mV
mV
mΩ
–
PACK+ = 2.5V, I(SWITCH) = –1mA to –2A
Battery overdischarged state switch permits
charge current only.
–600 –100
50
In Normal Mode (when not in OV or UV). This
value includes package and bondwire resistance.
PACK+ = 2.5V
75
Thermal Shutdown Section
TS
Thermal shutdown temperature. (Note 1)
135
°C
Note 1. This parameter is guaranteed by design. Not 100% tested in production.
PIN DESCRIPTIONS
give the battery pack user appropriate access to the bat-
tery. In an over-charged state, only discharge current is
permitted. In an over-discharged state, only charge cur-
rent is permitted.
BNEG: Connect the negative terminal of the battery to
this pin.
PACK+: Connect to the positive terminal of the battery.
This pin is available to the user.
SUB: (DP Package Only) Do not connect. These pins
must be electrically isolated from all other pins. These
pins may be soldered to isolated coppper pads for
heatsinking. However, most applications do not require
heatsinking.
CBPS: This power supply bypass pin is connected to
PACK+ through an internal 10K resistor. An external
0.1 F capacitor must be connected between this pin and
BNEG.
PACK–: The negative terminal of the battery pack (nega-
tive terminal available to the user). The internal FET
switch connects this terminal to the BNEG terminal to
TCLK: Production Test Mode pin. This pin is used to
provide a high frequency clock to the IC during produc-
tion testing. In an application this pin may be left uncon-
nected, or tied to BNEG.
3
UCC3952-1/-2/-3/-4
APPLICATION INFORMATION
PACK+ 16
10K
V
UV
CBPS 15
V
UVR
4-1
MUX
T
DEL
OV
STATE
MACHINE
LOGIC
V
1SEC
OVR
THRESHOLD
COMPARATOR
TCLK
N/C
1
2
3
4
5
6
7
8
9
V
OV
1.5V
T
SEL
DEL
UV
CLK
10mS
BNEG
BNEG
BNEG
BNEG
BNEG
BNEG
PACK–
SYSTEM
CLOCK
GENERATOR
TDLS
1mS
SETD
V
PUMP
50mV
2MΩ
RST
50mV
THERMAL
SHUTDOWN
PACK– 10
PACK– 11
PACK– 12
PACK– 13
PACK– 14
UDG-98209
PW package shown
Figure 1. Detailed block diagram.
APPLICATION INFORMATION
Fig. 1 shows a detailed block diagram of the UCC3952.
nects the load from the battery pack and enters a super
low power mode. The pack will remain in this state until it
detects the application of a charger, at which point
charging is enabled. The requirement of two consecutive
readings below the UV threshold filters out momentary
drops in cell voltage due to load transients, preventing
nuisance trips.
Battery Voltage Monitoring
The battery cell voltage is sampled every 8ms by con-
necting a resistor divider across it and comparing the re-
sulting voltage to a precision internal reference voltage.
Under normal conditions (cell voltage is below Over Volt-
age threshold and above Under Voltage threshold), the
UCC3952 consumes less than 10 A of current and the
internal MOSFET is fully turned on with the aid of a
charge pump.
If the cell voltage exceeds the Over Voltage threshold for
1sec, charging is disabled, however discharge current is
still allowed. This feature of the IC is explained further in
the section on Controlled Charge/Discharge Mode.
When the cell voltage falls below the Under Voltage
threshold for two consecutive samples, the IC discon-
4
UCC3952-1/-2/-3/-4
APPLICATION INFORMATION (cont.)
Over Current Monitoring and Protection
across the MOSFET to 100mV. When a light load is ap-
plied to the part, the loop adjusts the impedance of the
MOSFET to maintain 100mV across it. As the load in-
creases, the impedance of the MOSFET is decreased to
maintain the 100mV control. At heavy loads (still below
“over-current” limit level), the loop will not maintain regu-
lation and will drive the gate of the MOSFET to the bat-
tery voltage (not the charge-pump output voltage). The
MOSFET RDS(on) in the over-voltage state will be higher
than RDS(on) during normal operation. The voltage drop
(and associated power loss) across the internal MOSFET
in this mode of operation is still significantly lower than
the typical solution of two external back-to-back
MOSFETs, where the body diode is conducting.
Discharge current is continuously monitored via an inter-
nal sense resistor. In the event of excessive current, an
Over Current condition is declared if the high current
(over 3A) persists for over 1ms. This delay allows for
charging of the system bypass capacitors without trip-
ping the overcurrent. A 0.1 F capacitor on the CBPS pin
provides momentary holdup for the IC to assure proper
operation in the event that a hard short suddenly pulls
the cell voltage below the minimum operating voltage.
Once an Over Current condition has been declared, the
internal MOSFET turns off. The only way to return the
pack to normal operation is to remove the load by un-
plugging the pack from the system. The overcurrent is re-
set when an internal pull down brings PACK(–) to within
50mV of BNEG. At this point, the pack returns to its nor-
mal state of operation.
When the chip senses an under-voltage condition, it dis-
connects the load from the battery pack and shuts itself
down to minimize current drain from the battery. Several
circuits remain powered and will detect placement of the
battery pack into a charger. Once the charger presence
is detected, the linear loop is activated and the chip al-
lows charging current into the battery. This linear control
mode of operation is in effect until the battery voltage
reaches a level of VUVR, at which time normal operation
is resumed.
Controlled Charge/Discharge Mode
When the chip senses an over-voltage condition, it pre-
vents any additional charging, but allows discharge. This
is accomplished by activating a linear control loop which
controls the gate of the MOSFET based on the differen-
tial voltage across its drain to source terminals. The lin-
ear loop attempts to regulate the differential voltage
UNITRODE CORPORATION
7 CONTINENTAL BLVD. • MERRIMACK, NH 03054
TEL. (603) 424-2410 • FAX (603) 424-3460
5
相关型号:
©2020 ICPDF网 联系我们和版权申明