TPD4135AK [TOSHIBA]
TOSHIBA Intelligent Power Device High Voltage Monolithic Silicon Power IC; 东芝智能功率器件高压硅单片电源IC型号: | TPD4135AK |
厂家: | TOSHIBA |
描述: | TOSHIBA Intelligent Power Device High Voltage Monolithic Silicon Power IC |
文件: | 总23页 (文件大小:373K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TPD4135AK
TOSHIBA Intelligent Power Device
High Voltage Monolithic Silicon Power IC
TPD4135AK
The TPD4135AK is a DC brush less motor driver using high
voltage PWM control. It is fabricated by high voltage SOI process.
It is three-shunt resistor circuit for current sensing. It contains
level shift high-side driver, low-side driver, IGBT outputs, FRDs
and protective functions for under voltage protection circuits and
thermal shutdown circuit. It is easy to control a DC brush less
motor by just putting logic inputs from a MPU or motor controller
to the TPD4135AK.
HDIP26-P-1332-2.00
Weight: 3.8 g (typ.)
Features
•
•
•
•
•
•
•
•
•
•
High voltage power side and low voltage signal side terminal are separated.
It is the best for current sensing in three shunt resistance.
Bootstrap circuit gives simple high-side supply.
Bootstrap diodes are built in.
A dead time can be set as a minimum of 1.4 μs, and it is the best for a Sine-wave from drive.
3-phase bridge output using IGBTs.
FRDs are built in.
Included under voltage protection and thermal shutdown.
The regulator of 7 V (typ.) is built in.
Package: 26-pin DIP.
This product has a MOS structure and is sensitive to electrostatic discharge. When handling this product, ensure that
the environment is protected against electrostatic discharge.
1
2010-09-27
TPD4135AK
Pin Assignment
Marking
Lot Code.
(Weekly code)
TPD4135AK
Country of origin
Part No. (or abbreviation code)
2
2010-09-27
TPD4135AK
Block Diagram
V
BSU
BSV
BSW
18
CC
15
21
24
23
V
BB
7 V
V
REG
13
Regulator
Under-
voltage
Under-
voltage
Under-
voltage
Protection Protection Protection
Under-
voltage
Protection
High-side Level
Shift Driver
HU
HV
HW
LU
4
5
6
U
V
17
22
Thermal Shutdown
Input Logic
W
7
8
25
LV
Low-side
Driver
LW
SD
9
10
11
IS3
IS2
26
20
DIAG
IS1
19
GND
1/16
3
2010-09-27
TPD4135AK
Pin Description
Pin No.
Symbol
Pin Description
1
2
3
GND
NC
Ground pin.
Unused pin, which is not connected to the chip internally.
Unused pin, which is not connected to the chip internally.
NC
The control terminal of IGBT by the high side of U. It turns off less than 1.5V.
It turns on more than 2.5V.
The control terminal of IGBT by the high side of V. It turns off less than 1.5V.
It turns on more than 2.5V.
The control terminal of IGBT by the high side of W. It turns off less than 1.5V.
It turns on more than 2.5V.
The control terminal of IGBT by the low side of U. It turns off less than 1.5V.
It turns on more than 2.5V.
4
5
6
7
8
HU
HV
HW
LU
The control terminal of IGBT by the low side of V. It turns off less than 1.5V.
It turns on more than 2.5V.
LV
The control terminal of IGBT by the low side of W. It turns off less than 1.5V.
It turns on more than 2.5V.
9
LW
SD
10
11
Input pin of external protection. (“L” active, It doesn't have hysteresis)
With the diagnostic output terminal of open drain, a pull-up is carried out by resistance.
It turns on at the time of unusual.
DIAG
NC
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
Unused pin, which is not connected to the chip internally.
7V regulator output pin.
V
REG
NC
Unused pin, which is not connected to the chip internally.
Control power supply pin. (15V typ.)
Ground pin.
V
CC
GND
U
U-phase output pin.
BSU
IS1
IS2
BSV
V
U-phase bootstrap capacitor connecting pin.
U-phase IGBT emitter and FRD anode pin.
V-phase IGBT emitter and FRD anode pin.
V-phase bootstrap capacitor connecting pin.
V-phase output pin.
V
High-voltage power supply input pin.
W-phase bootstrap capacitor connecting pin.
W-phase output pin.
BB
BSW
W
IS3
W-phase IGBT emitter and FRD anode pin.
4
2010-09-27
TPD4135AK
Equivalent Circuit of Input Pins
Internal circuit diagram of HU, HV, HW, LU, LV, LW input pins
2 kΩ
2 kΩ
2 kΩ
HU/HV/HW
LU/LV/LW
To internal circuit
6.5 V
6.5 V
6.5 V
6.5 V
Internal circuit diagram of SD pin
V
REG
2 kΩ
2 kΩ
2 kΩ
SD
To internal circuit
6.5 V
6.5 V
6.5 V
6.5 V
Internal circuit diagram of DIAG pin
DIAG
To internal circuit
26 V
250kΩ
5
2010-09-27
TPD4135AK
Timing Chart
HU
HV
HW
LU
LV
Input Voltage
LW
VU
Output voltage VV
VW
6
2010-09-27
TPD4135AK
Truth Table
Input
LU
L
High side
Low side
DIAG
Mode
HU
H
H
L
HV HW
LV
H
L
LW
L
SD U phase V phase W phase U phase V phase W phase
Normal
L
L
H
H
L
L
L
L
H
H
L
L
L
L
H
H
L
L
L
L
H
H
L
L
*
L
L
L
L
H
H
L
L
L
L
H
H
L
L
L
L
H
H
L
L
L
L
H
H
*
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
L
ON
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
OFF
OFF
OFF
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
L
H
H
L
ON
L
L
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
L
H
H
L
L
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
L
L
L
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
L
H
H
L
L
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
Thermal shutdown
H
H
L
L
L
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ON
L
H
H
L
ON
L
L
ON
L
H
H
L
L
ON
L
L
L
ON
L
H
H
L
L
ON
V
Under-voltage
Under-voltage
SD
H
H
L
L
L
ON
CC
L
H
H
L
ON
L
L
ON
L
H
H
L
L
ON
L
L
L
ON
L
H
H
L
L
ON
V
H
H
L
L
L
OFF
OFF
OFF
OFF
OFF
OFF
ON
BS
L
H
H
L
OFF
OFF
OFF
OFF
ON
L
L
ON
L
H
H
L
L
OFF
OFF
OFF
OFF
L
L
L
ON
L
H
*
L
OFF
OFF
*
*
*
OFF
7
2010-09-27
TPD4135AK
Absolute Maximum Ratings (Ta = 25°C)
Characteristics
Symbol
Rating
Unit
V
500
V
V
BB
CC
out
Power supply voltage
V
18
Output current (DC)
Output current (pulse 1ms)
Input voltage
I
3
6
A
I
A
outp
V
-0.5 to 7
50
V
IN
V
current
I
mA
V
REG
REG
DIAG voltage
V
20
DIAG
DIAG
DIAG current
I
20
mA
Power dissipation
P
40
26
W
W
C(IGBT)
(IGBT 1 phase (Tc = 25°C) )
Power dissipation
P
C(FRD)
(FRD1 phase (Tc = 25°C) )
Operating junction temperature
Junction temperature
Storage temperature
T
-40 to 135
150
°C
°C
°C
jopr
T
j
T
-55 to 150
stg
Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even
if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum
ratings and the operating ranges.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
(“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test
report and estimated failure rate, etc).
8
2010-09-27
TPD4135AK
Electrical Characteristics (Ta = 25°C)
Characteristics
Symbol
Test Condition
Min
Typ.
Max
Unit
V
V
⎯
⎯
50
13.5
⎯
280
15
450
16.5
0.5
5
BB
CC
BB
CC
Operating power supply voltage
V
I
V
V
V
V
V
V
V
V
V
V
V
V
V
= 450 V
= 15 V
⎯
BB
CC
BS
BS
Current dissipation
mA
I
⎯
0.8
200
170
⎯
I
= 15 V, high side ON
= 15 V, high side OFF
⎯
410
370
⎯
BS (ON)
Bootstrap Current dissipation
μA
I
⎯
BS (OFF)
V
= “H”, V
CC
= 15 V
= 15 V
2.5
⎯
IH
IN
Input voltage
SD input voltage
Input current
V
V
V
= “L” , V
CC
⎯
1.5
⎯
IL
IN
V
SD
I
IH
= 15 V
⎯
2.5
⎯
CC
= 5 V
= 0 V
= 5 V
= 0 V
⎯
150
100
100
150
2.8
2.8
2.8
2.8
1.2
7.5
185
⎯
IN
μA
I
⎯
⎯
IL
IN
I
⎯
⎯
SDH
IN
SD Input current
μA
V
I
⎯
⎯
SDL
IN
V
H
= 15 V, I = 1.5 A, high side
⎯
2.1
2.1
1.9
1.9
0.8
7
CEsat
CC
CC
C
Output saturation voltage
FRD forward voltage
V
L
= 15 V, I = 1.5 A, low side
⎯
CEsat
V H
C
I
I
I
= 1.5 A, high side
= 1.5 A, low side
= 500 μA
⎯
F
F
F
F
V
V L
F
⎯
BSD forward voltage
V
⎯
V
V
F (BSD)
Regulator voltage
V
V
V
V
= 15 V, I
= 15 V
= 15 V
= 30 mA
REG
6.5
135
⎯
REG
TSD
ΔTSD
CC
CC
CC
Thermal shutdown temperature
Thermal shutdown hysteresis
⎯
°C
°C
V
50
V
V
V
V
under voltage protection
V
V
UVD
⎯
⎯
⎯
⎯
10
10.5
8
11
12
CC
CC
BS
BS
CC
CC
under voltage protection recovery
under voltage protection
UVR
UVD
UVR
11.5
9
12.5
9.5
10.5
0.5
3
V
V
V
V
BS
BS
under voltage protection recovery
8.5
⎯
9.5
⎯
V
DIAG saturation voltage
Output on delay time
Output off delay time
Dead time
V
I
= 5 mA
DIAG
V
DIAGsat
t
t
V
V
V
V
= 280 V, V
= 280 V, V
= 280 V, V
= 280 V, V
= 15 V, I = 1.5 A
⎯
1.8
1.3
⎯
μs
μs
μs
ns
on
BB
BB
BB
BB
CC
CC
CC
CC
C
= 15 V, I = 1.5 A
⎯
3
off
C
t
= 15 V, I = 1.5 A
1.4
⎯
⎯
dead
C
FRD reverse recovery time
t
= 15 V, I = 1.5 A
200
⎯
rr
C
9
2010-09-27
TPD4135AK
Application Circuit Example
15V
V
CC
15
18
21
24
23
BSU
+
C
C
5
4
BSV
BSW
V
BB
7 V
Under-
voltage
Under-
voltage
Under-
voltage
13
Regulator
V
REG
+
Protection Protection Protection
Under-
voltage
C
7
C
6
High-side
Level Shift
Driver
C
C C
2 3
1
Protection
Input Logic
C
4
5
6
7
8
9
HU
HV
HW
LU
17
22
25
Thermal
U
V
Control IC
or
M
Shutdown
Microcomputer
W
Low-side
Driver
LV
LW
IS3
26
20
19
11
10
DIAG
R
1
IS2
IS1
SD
R
R
R
R
2
1/16
GND
10
2010-09-27
TPD4135AK
External Parts
Typical external parts are shown in the following table.
Part
Typical
Purpose
Remarks
C , C , C
25 V/2.2 μF
25 V/10 μF
25 V/0.1 μF
25 V/1 μF
25 V/1000 pF
5.1 kΩ
Bootstrap capacitor
(Note 1)
(Note 2)
(Note 2)
(Note 2)
(Note 2)
(Note 3)
-
1
2
4
5
6
7
1
2
3
C
C
C
C
R
R
V
power supply stability
CC
V
for surge absorber
CC
V
power supply stability
REG
V
for surge absorber
REG
DIAG pin pull-up resistor
SD pin pull-up resistor
10 kΩ
Note 1: The required bootstrap capacitance value varies according to the motor drive conditions. The capacitor is
biased by V and must be sufficiently derated for it.
CC
Note 2: When using this product, adjustment is required in accordance with the use environment. When mounting,
place as close to the base of this product leads as possible to improve the ripple and noise elimination.
Note 3: The DIAG pin is open drain. If not using the DIAG pin, connect to the GND.
Handling precautions
(1) Please control the input signal in the state to which the V
voltage is steady. Both of the order of
CC
the V
power supply and the V
power supply are not cared about either.
BB
CC
Note that if the power supply is switched off as described above, this product may be destroyed if
the current regeneration route to the V power supply is blocked when the V line is
BB
BB
disconnected by a relay or similar while the motor is still running.
(2) The excess voltage such as the voltage surge which exceed the maximum rating is added, for
example, may destroy the circuit. Accordingly, be careful of handling this product or of surge voltage
in its application environment.
11
2010-09-27
TPD4135AK
Description of Protection Function
(1) Under voltage protection
This product incorporates under voltage protection circuits to prevent the IGBT from operating in
unsaturated mode when the V voltage or the V voltage drops. When the V power supply falls
CC
BS
CC
to this product internal setting V UVD (=11 V typ.), all IGBT outputs shut down regardless of the
CC
input. This protection function has hysteresis. When the V
power supply reaches 0.5 V higher than
CC
the shutdown voltage (V UVR (=11.5 V typ.)), this product is automatically restored and the IGBT
CC
is turned on again by the input. DIAG output is reversed at the time of V
under-voltage protection.
CC
When the V
power supply is less than 7 V, DIAG output isn't sometimes reversed. When the V
BS
CC
supply voltage drops V UVD (=9 V typ.), the high-side IGBT output shuts down.
BS
When the V supply voltage reaches 0.5 V higher than the shutdown voltage (V UVR (=9.5 V typ.)),
BS
BS
the IGBT is turned on again by the input signal.
(2) Thermal shutdown
This product incorporates a thermal shutdown circuit to protect itself against the abnormal state
when its temperature rises excessively. When the temperature of this chip rises to the internal setting
TSD due to external causes or internal heat generation, all IGBT outputs shut down regardless of the
input. This protection function has hysteresis ΔTSD (=50°C typ.). When the chip temperature falls to
TSD − ΔTSD, the chip is automatically restored and the IGBT is turned on again by the input.
Because the chip contains just one temperature detection location, when the chip heats up due to the
IGBT, for example, the differences in distance from the detection location in the IGBT (the source of
the heat) cause differences in the time taken for shutdown to occur. Therefore, the temperature of the
chip may rise higher than the thermal shutdown temperature when the circuit started to operate.
(3) SD pin
SD pin is the input signal pin to shut down the internal output IGBT. Output of all IGBT is shut down
after delay times (2 μs typ.) when "L" signal is input to the SD pin from external circuit (MCU etc.). It
is possible to shut down IC when overcurrent and others is detected by external circuit. Shut down
state is released by all of IC input signal "L". At open state of SD pin, shut down function can not
operate.
Timing Chart of Under voltage protection and SD Function
SD
LIN
HIN
VBS
VCC
LO
ton
toff
HO
ton
toff
DIAG
Note: The above timing chart is considering the delay time.
Safe Operating Area
3
2.7
0
0
400 450
(V)
Power supply voltage V
BB
Figure 1 SOA at Tj = 135 °C
Note 1: The above safe operating areas are Tj = 135 °C (Figure 1).
12
2010-09-27
TPD4135AK
V
H – T
V
L – T
CEsat
CEsat
j
j
3.4
3.0
2.6
2.2
1.8
1.4
3.4
3.0
2.6
2.2
1.8
1.4
V
= 15 V
V
= 15 V
CC
CC
I
C
= 2.7A
= 2.1A
I
= 2.7A
= 2.1A
C
I
I
C
C
I
I
= 1.5A
= 0.9A
I
= 1.5A
= 0.9A
C
C
C
I
C
−50
0
50
100
150
−50
0
50
100
150
Junction temperature
T
(°C)
Junction temperature
T
(°C)
j
j
V H – T
F
V L – T
F
j
j
2.8
2.4
2.0
1.6
1.2
2.8
2.4
2.0
1.6
1.2
I
I
= 2.7A
I
= 2.7A
F
F
I
= 2.1A
= 1.5A
F
= 2.1A
= 1.5 A
= 0.9A
F
I
F
F
I
F
I
I
= 0.9A
F
−50
0
50
100
150
−50
0
50
100
150
Junction temperature
T
(°C)
Junction temperature
T
(°C)
j
j
I
– V
V
– V
REG CC
CC
CC
2.0
1.5
1.0
0.5
0
8.0
7.5
7.0
6.5
6.0
T =−40°C
j
T =−40°C
j
T =25°C
j
T =25°C
j
T =135°C
j
T =135°C
j
I
= 30 mA
REG
12
14
16
18
12
14
16
18
Control power supply voltage
V
(V)
Control power supply voltage
V
(V)
CC
CC
13
2010-09-27
TPD4135AK
t
– T
t – T
off j
on
j
3.0
2.0
1.0
0
3.0
2.0
1.0
0
V
V
= 280 V
= 15 V
V
V
= 280 V
= 15 V
BB
CC
BB
CC
I
= 1.5 A
I = 1.5 A
C
C
High-side
Low-side
High-side
Low-side
−50
0
50
100
150
−50
0
50
100
150
Junction temperature
T
(°C)
Junction temperature
T
(°C)
j
j
V
UV – T
V
UV – T
BS j
CC
j
12.5
12.0
10.5
0.0
9.5
V
V
UVD
UVR
V
V
UVD
UVR
CC
CC
BS
BS
11.5
11.0
10.5
9.0
8.5
10.0
−50
8.0
−50
0
50
100
150
0
50
100
150
Junction temperature
T
(°C)
Junction temperature
T
(°C)
j
j
14
2010-09-27
TPD4135AK
I
– V
I
– V
BS (OFF) BS
BS (ON)
BS
500
400
300
200
100
500
400
300
200
100
T =−40°C
T =−40°C
j
j
T =25°C
j
T =25°C
j
T =135°C
j
T =135°C
j
12
14
16
18
12
14
16
18
Control power supply voltage
V
(V)
BS
Control power supply voltage VBS (V)
W
– T
j
W
– T
j
toff
ton
200
160
120
80
600
500
400
300
200
100
I
I
= 2.7A
= 2.1A
C
I
I
= 2.7A
= 2.1A
C
C
C
I
I
= 1.5A
= 0.9A
C
C
40
I
I
= 1.5A
= 0.9A
C
C
0
−50
0
50
100
150
−50
0
50
100
150
Junction temperature
T
(°C)
Junction temperature
T
(°C)
j
j
15
2010-09-27
TPD4135AK
Test Circuits
IGBT Saturation Voltage (U-phase low side)
1.5A
VM
HU = 0V
HV = 0V
HW = 0V
LU = 5V
LV = 0V
LW = 0V
VCC = 15V
FRD Forward Voltage (U-phase low side)
1.5A
VM
16
2010-09-27
TPD4135AK
V
CC
Current Dissipation
IM
VCC = 15V
Regulator Voltage
30mA
VM
VCC = 15V
17
2010-09-27
TPD4135AK
Output ON/OFF Delay Time (U-phase low side)
IM
U = 280V
187Ω
2.2μF
HU = 0V
HV = 0V
HW = 0V
LU = PG
LV = 0V
LW = 0V
VCC = 15V
5V
90%
10%
LU = PG
90%
10%
IM
ton
toff
18
2010-09-27
TPD4135AK
V
CC
Under-voltage Protection Operating/Recovery Voltage (U-phase low side)
U = 18V
2kΩ
HU = 0V
HV = 0V
HW = 0V
LU = 5V
LV = 0V
LW = 0V
V
CC = 15V → 6V
6V → 15V
VM
*Note: Sweeps the V
pin voltage from 15 V and monitors the U pin voltage.
CC
The V
pin voltage when output is off defines the under voltage protection operating voltage.
CC
Also sweeps from 6 V to increase. The V
protection recovery voltage.
pin voltage when output is on defines the under voltage
CC
V
BS
Under voltage Protection Operating/Recovery Voltage (U-phase high side)
VBB = 18V
VM
BSU = 15V → 6V
6V → 15V
2kΩ
HU = 5V
HV = 0V
HW = 0V
LU = 0V
LV = 0V
LW = 0V
V
CC = 15V
*Note: Sweeps the BSU pin voltage from 15 V to decrease and monitors the V
pin voltage.The BSU pin
BB
voltage when output is off defines the under voltage protection operating voltage.Also sweeps the
BSU pin voltage from 6 V to increase and change the HU pin voltage at 5 V→0 V→5 V each time. It
repeats similarly output is on. When the BSU pin voltage when output is on defines the under
voltage protection recovery voltage.
19
2010-09-27
TPD4135AK
Bootstrap Current Dissipation (U-phase high side)
IM
BSU = 15V
HU = 0V/5V
HV = 0V
HW = 0V
LU = 0V
LV = 0V
LW = 0V
VCC = 15V
20
2010-09-27
TPD4135AK
Turn-On/Off Loss (low side IGBT + high side FRD)
IM
VBB/U = 280V
5mH
2.2μF
L
VM
HU = 0V
HV = 0V
HW = 0V
LU = PG
LV = 0V
LW = 0V
VCC = 15V
Input (LU = PG)
IGBT (C-E Voltage)
(U-GND)
Power Supply Current
Wton
Wtoff
21
2010-09-27
TPD4135AK
Package Dimensions
HDIP26-P-1332-2.00
Unit: mm
Weight: 3.8 g (typ.)
22
2010-09-27
TPD4135AK
RESTRICTIONS ON PRODUCT USE
•
•
•
Toshiba Corporation, and its subsidiaries and affiliates (collectively “TOSHIBA”), reserve the right to make changes to the information
in this document, and related hardware, software and systems (collectively “Product”) without notice.
This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with
TOSHIBA’s written permission, reproduction is permissible only if reproduction is without alteration/omission.
Though TOSHIBA works continually to improve Product’s quality and reliability, Product can malfunction or fail. Customers are
responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and
systems which minimize risk and avoid situations in which a malfunction or failure of Product could cause loss of human life, bodily
injury or damage to property, including data loss or corruption. Before customers use the Product, create designs including the
Product, or incorporate the Product into their own applications, customers must also refer to and comply with (a) the latest versions of
all relevant TOSHIBA information, including without limitation, this document, the specifications, the data sheets and application notes
for Product and the precautions and conditions set forth in the “TOSHIBA Semiconductor Reliability Handbook” and (b) the
instructions for the application with which the Product will be used with or for. Customers are solely responsible for all aspects of their
own product design or applications, including but not limited to (a) determining the appropriateness of the use of this Product in such
design or applications; (b) evaluating and determining the applicability of any information contained in this document, or in charts,
diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operating
parameters for such designs and applications. TOSHIBA ASSUMES NO LIABILITY FOR CUSTOMERS’ PRODUCT DESIGN OR
APPLICATIONS.
•
Product is intended for use in general electronics applications (e.g., computers, personal equipment, office equipment, measuring
equipment, industrial robots and home electronics appliances) or for specific applications as expressly stated in this document.
Product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality and/or
reliability and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage or serious
public impact (“Unintended Use”). Unintended Use includes, without limitation, equipment used in nuclear facilities, equipment used
in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic signaling
equipment, equipment used to control combustions or explosions, safety devices, elevators and escalators, devices related to electric
power, and equipment used in finance-related fields. Do not use Product for Unintended Use unless specifically permitted in this
document.
•
•
Do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy Product, whether in whole or in part.
Product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any
applicable laws or regulations.
•
•
The information contained herein is presented only as guidance for Product use. No responsibility is assumed by TOSHIBA for any
infringement of patents or any other intellectual property rights of third parties that may result from the use of Product. No license to
any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise.
ABSENT A WRITTEN SIGNED AGREEMENT, EXCEPT AS PROVIDED IN THE RELEVANT TERMS AND CONDITIONS OF SALE
FOR PRODUCT, AND TO THE MAXIMUM EXTENT ALLOWABLE BY LAW, TOSHIBA (1) ASSUMES NO LIABILITY
WHATSOEVER, INCLUDING WITHOUT LIMITATION, INDIRECT, CONSEQUENTIAL, SPECIAL, OR INCIDENTAL DAMAGES OR
LOSS, INCLUDING WITHOUT LIMITATION, LOSS OF PROFITS, LOSS OF OPPORTUNITIES, BUSINESS INTERRUPTION AND
LOSS OF DATA, AND (2) DISCLAIMS ANY AND ALL EXPRESS OR IMPLIED WARRANTIES AND CONDITIONS RELATED TO
SALE, USE OF PRODUCT, OR INFORMATION, INCLUDING WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS
FOR A PARTICULAR PURPOSE, ACCURACY OF INFORMATION, OR NONINFRINGEMENT.
•
•
Do not use or otherwise make available Product or related software or technology for any military purposes, including without
limitation, for the design, development, use, stockpiling or manufacturing of nuclear, chemical, or biological weapons or missile
technology products (mass destruction weapons). Product and related software and technology may be controlled under the
Japanese Foreign Exchange and Foreign Trade Law and the U.S. Export Administration Regulations. Export and re-export of Product
or related software or technology are strictly prohibited except in compliance with all applicable export laws and regulations.
Please contact your TOSHIBA sales representative for details as to environmental matters such as the RoHS compatibility of Product.
Please use Product in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances,
including without limitation, the EU RoHS Directive. TOSHIBA assumes no liability for damages or losses occurring as a result of
noncompliance with applicable laws and regulations.
23
2010-09-27
相关型号:
TPD480505SW-1W
1W 1.5KVDC isolated Wide Input Twin output twin isolation regulated DC/DC converters
TOPPOWER
©2020 ICPDF网 联系我们和版权申明