OPA773 [TTELEC]
Power Line Designer Kit;型号: | OPA773 |
厂家: | TT Electronics |
描述: | Power Line Designer Kit 光电 |
文件: | 总2页 (文件大小:771K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
OVPL5W3K
Power Line Designer Kit
0.5-Watt LED Modules
OVPL5W3K
Contents:
•
•
Five (5) PCBs 8” in length
Three (3) 0.5-Watt white LEDs per PCB,
on-board regulator included
Wire harness with connector
Hand insertion tool
•
•
The self-contained Power Line Designer Kit is a flexible and scalable lighting solution using mid-power LEDs to
supply high luminous flux without additional heatsinking requirements. The kit includes components and
instructions to allow a designer to configure LED placement as needed for uniform illumination in his application.
With a 15-volt power supply (see Notes), the Power Line Kit is a total lighting solution.
Applications
PCB with 3LEDs
Optek Part No.
OPA773
•
•
•
•
•
•
Architectural accent lighting
Under-counter lighting
Media illumination
Lighting for large channel letters
Backlighting for light boxes
Point-of-sale displays
Viewing Typical Typical Luminous
Angle
CCT
Flux (lm) @ 15V*
50
1 board
100
150
200
250
2 boards
3 boards
4 boards
5 boards
White
5750K
120°
*125mA per board stabilized
8.75” by 1.5”Ø tube
5 PCBs 8.00” x 0.425” wide
(.062 FR4 material)
4’ Wire harness
with connector
Notes:
Hand Insertion Tool
•
All electrical and optical characteristics of the LEDs remain the
same as specified in Optek Datasheet OVS5WBCR4.
•
•
•
Maximum storage and operating temperature –40° ~ +100°C
ESD threshold (HBM) 2000V
RoHS
DO NOT LOOK DIRECTLY
AT LED WITH UNSHIELDED
EYES OR DAMAGE TO
RETINA MAY OCCUR.
14-16V power supply not included. 1.0A minimum rating
required, regulated or unregulated.
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
Issue A.3 06/08
Page 1 of 2
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 visibleLED@optekinc.com www.optekinc.com
OVPL5W3K
OVPL5W3K
Power Line Designer Kit
OVPL5W3K
OPA773 Dimensions
8.000 [203.20]
- BLACK WIRE
+ RED WIRE
14-16 VOLT
DC INPUT
Remove adhesive backing
Place in desired position
200mA min. per strip Attach 28-26 gauge wires with tool #9175
OPA773
[10.79]
0.425
3.000 [76.20]
1.287 [32.68]
3.000 [76.20]
Suggested Design Options
Number of LEDs per Number of Strips
LED Drive Current
per Strip
Supply
Voltage
AWG
Optek Part Number
Strip
per Buss
3
1 to 5
125mA
125mA
125mA
Other
26-28
18
14-16V
OPA773 (included in kit)
OPA775
3
3
1 to 30
2 to 60*
Other
14-16V
24V
18
OPA776
Other
Other
Other
Optek Custom Assembly**
*Multiples of 2 only
**Contact Optek or an authorized distributor to discuss your application.
Instructions
1. Install backplane (not included) behind panel to be
illuminated.
2. Use masking tape (not included) to temporarily
position the boards on backplane.
3. Route wire harness to each strip:
•
•
•
Start with loose end and work to-
ward 2.1mm jack.
Use insertion tool to insert red and
black wires on each board.
Leave several inches of slack be-
tween each strip.
4. Connect the 2.1mm jack to 14-16V power supply
(not included, must be rated at 1.0A minimum).
5. Reposition all boards until optimal illumination is
achieved.
6. Peel tape backing from boards.
7. Permanently apply boards to backplane.
Note: Steps 6 and 7 are optional—do not peel off
backing if the kit will be reused.
Output connector
2.1mm ID/5.5mm OD
OPTEK reserves the right to make changes at any time in order to improve design and to supply the best product possible.
OPTEK Technology Inc. — 1645 Wallace Drive, Carrollton, Texas 75006
Issue A.3 06/08
Page 2 of 2
Phone: (972) 323-2200 or (800) 341-4747 FAX: (972) 323-2396 visibleLED@optekinc.com www.optekinc.com
OVPL5W3K
相关型号:
©2020 ICPDF网 联系我们和版权申明