MS122910 [UMPCO]

CLAMP, LOOP, TYPE SUPPORT, (HEAT RESISTANT) .204 HOLE;


型号：	MS122910
厂家：	UMPCO
描述：	CLAMP, LOOP, TYPE SUPPORT, (HEAT RESISTANT) .204 HOLE
文件：	总1页 (文件大小：68K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

.150

.090

MARK PART

NUMBER

DEPRESSED

.003 MAX

ROLL INSIDE

EDGES

 .209/.199

 A

F RAD

.223

.213

D GAP

.258

.242

R. .391/.359

.516

.484

NOM

TUBE

DIA

PART NUMBER

±.005

±.010

RAD

±.016

BASIC

0.125

0.188

0.250

0.312

0.375

0.438

0.500

0.562

0.625

0.688

0.750

0.812

0.875

0.938

1.000

1.062

1.125

1.188

1.250

1.312

1.375

1.438

1.500

1.562

1.625

1.750

1.875

2.000

MS122900

MS122901

MS122902

MS122903

MS122904

MS122905

MS122906

MS122907

MS122908

MS122909

MS122910

MS122911

MS122912

MS122913

MS122914

MS122915

MS122916

MS122917

MS122918

MS122919

MS122920

MS122921

MS122922

MS122923

MS122924

MS122925

MS122926

MS122927

0.125

0.188

0.250

0.312

0.375

0.438

0.500

0.562

0.625

0.688

0.750

0.812

0.875

0.938

1.000

1.062

1.125

1.188

1.250

1.312

1.375

1.438

1.500

1.562

1.625

1.750

1.875

2.000

0.360

0.423

0.457

0.498

0.529

0.560

0.592

0.623

0.654

0.752

0.783

0.814

0.845

0.877

0.908

0.939

0.970

1.002

1.062

1.093

1.125

1.156

1.188

1.219

1.250

1.312

1.375

1.438

0.031

0.062

.062-.078

0.051

0.109

.094-.110

.094-.125

0.064

0.125

MATERIAL: CORROSION RESISTANT STEEL PER AMS 5510

REMOVE BURRS AND SHARP EDGES.

DIMENSIONS IN INCHES

CLAMP SHALL BE FORMED AS SHOWN. DIMENSION “D” SHALL FALL WITHIN THE SPECIFIED LIMITS WHEN

CLAMP IS ASSEMBLED ON A BAR THE DIA OF WHICH IS EQUAL TO THE NOMINAL TUBE OD WITHIN ±.001.

HOLES SHALL BE IN ALIGNMENT WITHIN .010 AND CLAMP SHALL BE FLAT WITHIN .010 THRU CLAMP

WIDTH WHEN ASSEMBLE ON A TEST BAR. IN THE FREE POSITION CLAMP MAY SPRING OPEN PROVIDED

THE ABOVE CONDITIONS ARE MET.

DO NOT USE UNASSIGNED PART NUMBER.

THIS CATALOG PAGE IS FOR REFERENCE ONLY. REQUEST

REV

N/C

02/18/09

UMPCO, INC

CAGE CODE No. 18076

CERTIFIED UMPCO DRAWING FOR ACTUAL SPECIFICATIONS.

ANY CONFLICT BETWEEN THIS DOCUMENT AND THE CERTIFIED

DRAWING, THE CERTIFIED DRAWING WILL TAKE PRECEDENCE.

IF THE DOCUMENT IS CONTROLLED BY ANY OTHER SOURCE

THAN UMPCO, THE CERTIFIED DRAWING MUST BE PURCHASED

THROUGH THAT ORGANIZATION.

AS122900

PART NUMBER

CLAMP, LOOP, TYPE SUPPORT, (HEAT RESISTANT) .204 HOLE

7100 LAMPSON AVE * PO BOX 5158 * GARDEN GROVE, CA 92846-5158 SALES: (714) 897-3531 * BUS: (714) 897-3536 * FAX: (714) 897-2611

相关型号：