MS9354-27 [UMPCO]

CLAMP, LOOP-ALUMINUM, .265 HOLE;


型号：	MS9354-27
厂家：	UMPCO
描述：	CLAMP, LOOP-ALUMINUM, .265 HOLE
文件：	总1页 (文件大小：73K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

.150

.090

∅ A

ROLL INSIDE

EDGES

MARK PART NO. PER

AS 478 CLASS D

.270

.260

F RAD

.223

.213

391/.351 RADIUS

.250

.500

TABLE 1 – DIMENSIONS AND PART NUMBERS

NOM

TUBE

PART NO.

DIA

±.005

±.015

RAD

±.016

BASIC

MS9354-01

MS9354-02

MS9354-03

MS9354-04

MS9354-05

MS9354-06

MS9354-07

MS9354-08

MS9354-09

MS9354-10

MS9354-11

MS9354-12

MS9354-13

MS9354-14

MS9354-15

MS9354-16

MS9354-17

MS9354-18

MS9354-19

MS9354-20

MS9354-21

MS9354-22

MS9354-23

MS9354-24

MS9354-25

MS9354-26

MS9354-27

MS9354-28

MS9354-29

MS9354-30

MS9354-31

0.125

0.188

0.250

0.312

0.375

0.438

0.500

0.562

0.625

0.688

0.750

0.812

0.875

0.938

1.000

1.062

1.125

1.188

1.250

1.312

1.375

1.438

1.500

1.562

1.625

1.688

1.750

1.812

1.875

1.938

2.000

0.125

0.188

0.250

0.312

0.375

0.438

0.500

0.562

0.625

0.688

0.750

0.812

0.875

0.938

1.000

1.062

1.125

1.188

1.250

1.312

1.375

1.438

1.500

1.562

1.625

1.688

1.750

1.812

1.875

1.938

2.000

0.360

0.423

0.457

0.498

0.529

0.560

0.592

0.623

0.654

0.752

0.783

0.814

0.845

0.877

0.908

0.939

0.970

1.002

1.062

1.093

1.125

1.156

1.188

1.219

1.250

1.281

1.312

1.344

1.375

1.406

1.438

0.031

0.062

.062/.078

0.051

0.109

.094/.110

.094-.125

0.064

0.125

MATERIAL: ALUMINUM PER AMS 4041

REMOVE BURRS AND SHARP EDGES

DIMENSIONS ARE IN INCHES

CLAMP SHALL BE FORMED AS SHOWN. DIMENSION “D” SHALL FALL WITHIN THE SPECIFIED

LIMITS WHEN CLAMP IS ASSEMBLED ON A BAR, THE DIAMETER OF WHICH IS EQUAL TO THE

NOMINAL TUBE OD WITHIN ±.001.

HOLES SHALL BE IN ALIGNMENT WITHIN .010 AND CLAMP SHALL BE FLAT WITHIN .010 THRU THE

CLAMP WIDTH WHEN ASSEMBLED ON A TEST BAR. IN THE FREE POSITION, CLAMP MAY SPRING

OPEN PROVIDED THE ABOVE CONDITIONS ARE MET.

DO NOT USE UNASSIGNED PART NUMBERS.

THIS CATALOG PAGE IS FOR REFERENCE ONLY. REQUEST

REV

N/C

02/05/09

UMPCO, INC

CAGE CODE No. 18076

CERTIFIED UMPCO DRAWING FOR ACTUAL SPECIFICATIONS.

ANY CONFLICT BETWEEN THIS DOCUMENT AND THE CERTIFIED

DRAWING, THE CERTIFIED DRAWING WILL TAKE PRECEDENCE.

IF THE DOCUMENT IS CONTROLLED BY ANY OTHER SOURCE

THAN UMPCO, THE CERTIFIED DRAWING MUST BE PURCHASED

THROUGH THAT ORGANIZATION.

AS9354

PART NUMBER

CLAMP, LOOP-ALUMINUM, .265 HOLE

7100 LAMPSON AVE * PO BOX 5158 * GARDEN GROVE, CA 92846-5158 SALES: (714) 897-3531 * BUS: (714) 897-3536 * FAX: (714) 897-2611

相关型号：