8565G-S08-T [UTC]
HIGH PERFORMANCE POWER FACTOR CORRECTION; 高性能功率因数校正型号: | 8565G-S08-T |
厂家: | Unisonic Technologies |
描述: | HIGH PERFORMANCE POWER FACTOR CORRECTION |
文件: | 总13页 (文件大小:363K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
UNISONIC TECHNOLOGIES CO., LTD
8565
Preliminary
LINEAR INTEGRATED CIRCUIT
HIGH PERFORMANCE POWER
FACTOR CORRECTION
CONTROLLER IN CONTINUOUS
CONDUCTION MODE
DESCRIPTION
The UTC 8565 is a wide input range controller integrated circuit for
active power factor correction. The circuit is designed for boost PFC
application, and requires reduced external component count. Its power
supply is recommended to be provided by an external auxiliary supply
which will switch on and off the IC.
The circuit operates in the continuous conduction mode under average
current, and in discontinuous conduction mode only in light load
condition. The switching frequency can be set with the external resistor at
pin 4. Both current and voltage loop compensations are done externally
to allow full user control.
There are many kinds of protection features incorporated to make sure of safe system operation conditions, such as
brown-out protection, output under voltage detection and peak current limitation. The inside reference is adjusted
(5V±2%) to make sure control level and precise protection. There is a particular soft-start function to limit the start up
current and thus reduces the stress on the boost diode.
FEATURES
* Supports wide input range
* Under voltage lockout
* Average current control
* Cycle by cycle peak current limiting
* Over-voltage protection
* Open loop detection
* Output under-voltage detection
* Brown-out protection
* Soft Over current Protection
* Enhanced dynamic response
* Ease of use with few external components
* External current and voltage loop compensation
* Trimmed internal reference voltage (5V±2%)
* Programmable operating/switching frequency
* (50kHz ~ 250kHz)
* Max duty cycle of 95% (typ) at 125kHz
ORDERING INFORMATION
Ordering Number
Lead Free
Package
Packing
Halogen Free
8565G-S08-R
8565G-S08-T
8565L-S08-R
SOP-8
SOP-8
Tape Reel
Tube
8565L-S08-T
8565L-S08-R
(1) R: Tape Reel, T: Tube
(2) S08: SOP-8
(1)Packing Type
(2)Package Type
(3)Lead Free
(3) G: Halogen Free, L: Lead Free
www.unisonic.com.tw
1 of 13
Copyright © 2012 Unisonic Technologies Co., Ltd
QW-R114-004.b
8565
Preliminary
LINEAR INTEGRATED CIRCUIT
PIN CONFIGURATION
VCC
1
2
3
4
GND
ICOMP
8
GATE
VSENSE
VCOMP
7
6
ISENSE
FREQ
5
PIN DESCRIPTION
PIN NO.
PIN NAME
VSENSE
DESCRIPTION
The output bus voltage of the boost converter is sensed at this pin via a resistive divider.
The reference voltage for this pin is 5V.
1
This VCOMP Pin provides the compensation of the output voltage loop with a
compensation network to ground (see Fig. 2). This also gives the soft start function which
controls an increasing AC input current during start-up.
2
VCOMP
At this pin the compensation components of the current loop are connected. The
capacitor which is connected at this pin integrates the output current of OTA2 and
averages the current sense signal.
3
4
ICOMP
A resistor connected to this pin sets the fixed switching frequency. The frequency range
is from 50kHz to 250kHz.
FREQ
The pin senses the negative voltage drop at the external sense resistor (R1). This is the
input signal for the average current regulation in the current loop. It is also fed to the
peak current limitation block. During power up time, high inrush currents cause high
voltage drop at R1, driving currents into pin 5 which could be beyond the absolute
maximum ratings. Therefore a series resistor (R2) of around 220Ω is recommended in
order to limit this current into the IC.
5
ISENSE
6
7
GND
This is the Ground pin.
The GATE pin is the output of the internal driver stage, which has a capability of 1.5A
source and sink current. Its gate drive voltage is clamped at 11.5V (typically).
The VCC pin is the positive supply of the IC and should be connected to an external
auxiliary supply. The operating range is between 10V and 21V. The turn-on threshold is
at 11.2V and under voltage occurs at 10.2V.
GATE
8
VCC
UNISONIC TECHNOLOGIES CO., LTD
2 of 13
QW-R114-004.b
www.unisonic.com.tw
8565
Preliminary
LINEAR INTEGRATED CIRCUIT
BLOCK DIAGRAM
RFI Filter
D2...D5
L1
D1
R3
R4
VOUT
Vin
C1
C2
85...265 VAC
R7
R1
R2
auxiliary supply
VCC
GND
GATE
UTC 8565
Variable Oscillator
PWM Logic
Gate Driver
2.5V
OTA3
OSC CLK
R
S
+
-
FREQ
250ns
Toff min
R
S
R5
Protection Block
VCC
Peak Current Limit
Current Sense
Ramp Generator
PWM Comp
UV lockout
+
C4
-
OUP
Opamp -1.43x
Protection
Logic
OP1
2.5V
0.8V
VSENSE
+
C1
-
Over-current
Comp
Fault
300ns
+
-
C2
+
C3
-
1.5V
ISENSE
Deglitcher
OLP
Fault
S1
Voltage Loop
0.73V
Current Loop
+/-30μA, 42μS
0
Current Loop Comp
-
OTA1
+
ICOMP
-ve
+
5V
OTA2
Soft Over
Current Control
-
Nonlinear
Gain
1.1mS
+/-50μA linear range
C3
Soft Start
4.0V
4.75V
+ve
5.25V
S2
VCOMP
0
4.0V
-ve
R6
C4
Fault
Window Detect
C5
Representative Block diagram
UNISONIC TECHNOLOGIES CO., LTD
3 of 13
QW-R114-004.b
www.unisonic.com.tw
8565
Preliminary
LINEAR INTEGRATED CIRCUIT
ABSOLUTE MAXIMUM RATINGS
PARAMETER
SYMBOL
VCC
RATINGS
-0.3 ~ 22
-0.3 ~ 7
-0.3 ~ 7
-24 ~ 7
±1
UNIT
V
VCC Supply Voltage
FREQ Voltage
VFREQ
VICOMP
VISENSE
IISENSE
VVSENSE
IVSENSE
VVCOMP
VGATE
VESD
V
ICOMP Voltage
V
ISENSE Voltage
ISENSE Current
VSENSE Voltage
VSENSE Current
VCOMP Voltage
GATE Voltage
V
mA
V
-0.3 ~ 7
±1
mA
V
-0.3 ~ 7
-0.3 ~ 22
2
V
ESD Protection (Note 2)
Junction Temperature
Storage Temperature
kV
°C
°C
TJ
-40 ~ 150
-55 ~ 150
TSTG
Notes: 1. Absolute maximum ratings are those values beyond which the device could be permanently damaged.
Absolute maximum ratings are stress ratings only and functional device operation is not implied.
2. According to EIA/JESD22-A114-B (discharging a 100pF capacitor through a 1.5kΩ series resistor)
THERMAL DATA
PARAMETER
SYMBOL
RATINGS
90
UNIT
K/W
Junction to Ambient
θJA
ELECTRICAL CHARACTERISTICS
PARAMETER
SYMBOL
TEST CONDITIONS
MIN
TYP
MAX UNIT
OPERATING RANGE (Note 1)
VCC Supply Voltage
VCC
VCCUVLO
-40
21
V
Junction Temperature
TJ(CON)
125
°C
SUPPLY SECTION (Note 2)
VCC Turn-On Threshold
VCC Turn-Off Threshold/
Under Voltage Lock Out
VCC Turn-On/Off Hysteresis
Start Up Current Before VCCON
Operating Current With Active
GATE
VCCON
VCCUVLO
VCCHY
10.5
9.4
11.2
10.2
11.9
10.8
V
V
0.8
50
1
1.3
V
ICCSTART VVCC=VVCC(ON)-0.1V
100
200
µA
ICCHG R5=33kΩ, CL=4.7nF
13.5
2.0
18
22.5
3.2
mA
mA
Operating Current During Standby ICCSTDBY R5 = 33kΩ, VVSENSE=0.5V
2.6
VARIABLE FREQUENCY SECTION
Switching Frequency (Typical)
Switching Frequency (Min.)
Switching Frequency (Max.)
Voltage At FREQ Pin
PWM SECTION
FSWNOM R5=33kΩ
FSW(MIN) R5=82kΩ
FSW(MAX) R5=15kΩ
VFREQ
106
40
133
56
161
70
kHz
kHz
kHz
V
200
2.40
250
2.50
320
2.60
Max. Duty Cycle
DMAX
DMIN
FSW=FSWNOM (R5=33kΩ)
VVCOMP=0V, VVSENSE=5V, VICOMP=6.4V
92
95
98
0
%
%
ns
Min. Duty Cycle
Min. Off Time
TOFF(MIN) VVCOMP=5V, VVSENSE=5V, VISENSE=0.1V 150
250
350
UNISONIC TECHNOLOGIES CO., LTD
4 of 13
QW-R114-004.b
www.unisonic.com.tw
8565
Preliminary
LINEAR INTEGRATED CIRCUIT
ELECTRICAL CHARACTERISTICS(Cont.)
PARAMETER
SYMBOL
TEST CONDITIONS
MIN TYP MAX UNIT
SYSTEM PROTECTION SECTION
Open Loop Protection (OLP)
VOLP
VPCL
VSOC
0.77 0.81 0.86
-1.15 -1.08 -1.00
-0.79 -0.73 -0.66
V
V
V
V
SENSE Threshold
Peak Current Limitation (PCL)
SENSE Threshold
I
Soft Over Current Control (SOC) ISENSE
Threshold
Output Under Voltage Detection (OUV)
VOUV
VOVP
2.45 2.55 2.65
5.12 5.25 5.38
V
V
VSENSE Threshold
Output Over-Voltage Protection (OVP)
CURRENT LOOP SECTION
OTA2 Transconductance Gain
OTA2 Output Linear Range
ICOMP Voltage during OLP
VOLTAGE LOOP SECTION
OTA1 Reference Voltage
OTA1 Transconductance Gain
OTA1 Max. Source Current Under
Normal Operation
GmOTA2 At Temp=25°C
0.9
3.6
1.1
±50
4.0
1.3 mS
IOTA2
Guaranteed by design
µA
V
VICOMPF VVSENSE=0.5V
VOTA1
4.90 5.00 5.10
V
GmOTA1
31.5 42 52.5 µS
IOTA1SO VVSENSE=4.25V, VVCOMP=4V
21
21
30
30
38
38
µA
OTA1 Max. Sink Current Under
Normal Operation
IOTA1SK VVSENSE=6V, VVCOMP=4V
VSOFT
µA
V
Soft Start End
3.80 4.00 4.20
OTA1 Source Current Under Soft Start IOTA1SS VVSENSE=2V, VVCOMP=0V
8.0 10.8 13.4 µA
VSENSE High
VSENSE Low
VHi
5.12 5.25 5.38
4.63 4.75 4.87
V
V
Enhanced Dynamic
Response
VLo
VSENSE Input Bias Current At 5V
VSENSE Input Bias Current at 1V
VCOMP Voltage during OLP
DRIVER SECTION
IVSEN5V VVSENSE=5V
IVSEN1V VVSENSE=1V
VVCOMPF VVSENSE= 0.5V, IVCOMP=0.5mA
0
0
0
1.5
1
µA
µA
V
0.2
0.4
VCC=5V, IGATE=5mA
VCC=5V, IGATE=20mA
VGATEL IGATE=0A
1.2
1.5
V
V
GATE Low Voltage
GATE High Voltage
0.8
1.6
V
IGATE=20mA
2.0
V
IGATE=-20mA
-0.2 0.2
11.5
10.5
7.5
V
VCC=20V, CL=4.7nF
VGATEH VCC=11V, CL =4.7nF
VCC=VVCC(OFF)+0.2V, CL=4.7nF
V
V
V
GATE Rise Time
tR
VGATE=2V...9V, CL=4.7nF
VGATE=9V...2V, CL=4.7nF
CL=4.7nF (Note 3)
20
ns
ns
A
GATE Fall Time
tF
20
GATE Current, Peak, Rising Edge
GATE Current, Peak, Falling Edge
IGATE
IGATE
-1.5
CL=4.7nF (Note 3)
1.5
A
Notes: 1. Within the operating range the IC operates as described in the functional description.
2. The electrical characteristics involve the spread of values within the specified supply voltage and junction
temperature range TJ from -40°C to 125°C. Typical values represent the median values, which are related
to 25°C. If not otherwise stated, a supply voltage of VCC=15V is assumed for test condition.
3. Design characteristics (not meant for production testing)
UNISONIC TECHNOLOGIES CO., LTD
5 of 13
QW-R114-004.b
www.unisonic.com.tw
8565
Preliminary
LINEAR INTEGRATED CIRCUIT
FUNCTIONAL DESCRIPTION
1. General
The UTC 8565 is an active power factor correction controller for boost PFC application. The IC comes in DIP
package and is suitable for wide input range applications from 85 to 265 VAC. The IC is usually realized with boost
converters and it operates in continuous conduction mode with average current control.
The UTC 8565 operates with a cascaded control; the inner current loop and the outer voltage loop. The inner
current loop of the IC controls the sinusoidal profile for the average input current. It uses the dependency of the
PWM duty cycle on the line input voltage to determine the corresponding input current. This means the average
input current follows the input voltage as long as the device operates in CCM. Under light load condition, depending
on the choke inductance, the system may enter into discontinuous conduction mode (DCM). In DCM, the average
current waveform will be distorted but the resultant harmonics are still low enough to meet the Class D requirement
of IEC 1000-3-2. The outer loop controls the output voltage. Depending on the load condition, OTA1 establishes an
appropriate voltage at VCOMP pin which controls the amplitude of the average input current.
The UTC 8565 provides several protection features to ensure safe operating condition for both the system and
device. Important protection features are namely Brown-out protection, Current Limitation and Output Under-voltage
Protection.
2. Power Supply
The operating voltage range of the VCC is from 10V to 21V. An internal under voltage lockout (UVLO) block
monitors the VCC power supply. As soon as it exceeds 11.2V and the voltage at pin 1 (VSENSE) is >0.8V, the IC
begins operating its gate drive and performs its Soft-Start as shown in Fig. 3.
If VCC drops below 10.2V, the IC is off. The IC will then be consuming typically 200µA, whereas consuming 18mA
during normal operation.
The IC can be turned off and forced into standby mode by pulling down the voltage at pin 1 (VSENSE) to lower than
0.8V. The current consumption is reduced to 3mA in this mode.
UNISONIC TECHNOLOGIES CO., LTD
6 of 13
QW-R114-004.b
www.unisonic.com.tw
8565
Preliminary
LINEAR INTEGRATED CIRCUIT
FUNCTIONAL DESCRIPTION(Cont.)
3. Start-up (Soft-Start)
The operation of OTA1 during startup is shown in Fig. 4 and 5.
VSENSE
R4
R3+R4
)
×VOUT
(
Soft Start
OUT<80% rated
Normal Operation
VOUT>80% rated
4.0V
Soft Start
V
10.8μA during
Soft Start
-
OTA1
+
5V
VCOMP
-
C3
S1
Open-Loop
Protect
+
av(IIN)
0.8V
R6
C4
(OLP)
UTC 8565
C5
t
Fig. 4 Soft Start Circuit
Fig. 5 Soft Start With Controlled Current
It sources a constant 10.8µA into the compensation network at pin 2 (VCOMP). The voltage at this pin rises
linearly and so does the amplitude of the input current. As soon as the output voltage VOUT reaches 80% of its rated
level, the startup procedure is finished and the normal voltage control takes over. In normal operation, the IC
operates with a higher maximum current at OTA1 and therefore with a higher voltage loop gain in order to improve
the dynamic behavior of the device.
The advantage of this technique is a soft-start function with lower stress for the boost diode but without the risk of
audible noise.
4. System Protection
The IC is equipped with various protection features to ensure the PFC system in safe operating range. Depending
on the input line voltage (VIN) and output bus voltage (VOUT), When these protections are active the conditions are
shown in Fig. 6 and 7.
The following sections describe the functionality of these protection features.
UNISONIC TECHNOLOGIES CO., LTD
7 of 13
QW-R114-004.b
www.unisonic.com.tw
8565
Preliminary
LINEAR INTEGRATED CIRCUIT
FUNCTIONAL DESCRIPTION(Cont.)
4.1 Brown-Out Protection (BOP)
Input Brown-out occurs if the input voltage VIN falls below the minimum input voltage of the design (i.e. 85V for
universal input voltage range) and the VCC has not entered into the VCC under voltage lockout level yet. For a system
without BOP, the boost converter will increasingly draw a higher current from the mains at a given output power
which may exceed the maximum design values of the input current. The UTC 8565 limits internally the current drawn
from the mains and therefore also limits the input power. The difference of input and output power will result in
decreasing output voltage. If the condition prolongs, the decreasing VOUT will terminate in output under voltage
condition (OUV, 50% of rated), and the IC will be shut down (See section 4.5).
Fig. 8 shows the occurrence of BOP in respect to the ISENSE voltage.
The VIN threshold for BOP to occur is dependent on the voltage at ISENSE and thus the output power. The rated
output power with a minimum VIN (VIN(MIN)) is
0.6
POUT(rated) = V
×
R1×
INMIN
2
Due to the internal parameter tolerance, the maximum power with VIN(MIN) before BOP occurs is
0.73
POUT(max) = V
×
R1×
INMIN
2
And the BOP takes over the normal operation under rated output power latest at an input voltage of
2
0.73
VBOPMAX = POUT (rated)× R1×
4.2 Soft Over Current Control (SOC)
The UTC 8565 is designed not to support any output power that corresponds to a voltage lower than -0.73V at the
I
SENSE pin. A further increase in the inductor current, which results in a lower ISENSE voltage, will activate the Soft Over
Current Control (SOC). This is a soft control as it does not directly switch off the gate drive like the PCL. It acts on
the nonlinear gain block to result in a reduced PWM duty cycle.
4.3 Peak Current Limit (PCL)
The UTC 8565 is equipped with a cycle by cycle peak current protection feature. It is active when the voltage at
pin 5 (ISENSE) reaches -1.08V. This voltage is amplified by OP1 with a factor of -1.43 and connected to comparator
C2 with a reference voltage of 1.5V as shown in Fig. 9. A deglitcher with 300ns after the comparator improves noise
immunity to the activation of this protection.
UNISONIC TECHNOLOGIECO., LTD
8 of 13
QW-R114-004.b
www.unisonic.com.tw
8565
Preliminary
LINEAR INTEGRATED CIRCUIT
FUNCTIONAL DESCRIPTION(Cont.)
4.4 Open Loop Protection / Input Under Voltage Protect (OLP)
Whenever VSENSE voltage falls below 0.8V, or equivalently VOUT falls below 16% of its rated value, it indicates an
open loop condition (i.e. VSENSE pin not connected) or an insufficient input voltage VIN for normal operation. In this
case, most of the blocks within the IC will be shutdown. The function is implemented using comparator C3 with a
threshold of 0.8V as shown in the IC block diagram in Fig. 2.
4.5 Output Under Voltage Detection (OUV)
In the event of main interrupt or brown-out condition, the PFC system is not able to deliver the rated output power.
This will cause the output voltage VOUT to drop below its rated value. The IC provides an output under voltage
detection that checks if VOUT is falling below 50% of its rated value. Comparator C4 as shown in the device block
diagram (Fig. 2) senses the voltage at pin 1 (VSENSE) with a reference of 2.5V. If comparator C4 trips, the IC will be
shut down as in OLP. The IC will be ready to restart if there is sufficient VIN to pull VOUT out of OLP.
4.6 Over-Voltage Protection (OVP)
Whenever VOUT exceeds the rated value by 5%, the over-voltage protection OVP is active as shown in Fig. 7. This
is implemented by sensing the voltage at pin VSENSE with respect to a reference voltage of 5.25V. A VSENSE voltage
higher than 5.25V will immediately reduce the output duty cycle, bypassing the normal voltage loop control. This
results in a lower input power to reduce the output voltage VOUT
.
5. Frequency Setting
The switching frequency of the PFC controller is fixed and can be set by an external resistor R5 at FREQ pin. The
pin voltage VFREQ is typically 2.5V. The corresponding capacitor for the oscillator is integrated in the device and the
R5/frequency relationship is given at the “Electrical Characteristic” section. The recommended operating frequency
range is from 50kHz to 250kHz. As an example, a R5 of 33kΩ at pin FREQ will set a switching frequency FSW of
133kHz typically.
6. Average Current Control
6.1 Complete Current Loop
Fig. 10 show the complete system current loop. It consists of the current loop block which averages the voltage at
pin ISENSE, resulted from the inductor current flowing across R1. The averaged waveform is compared with an
internal ramp in the ramp generator and PWM block. Once the ramp crosses the average waveform, the comparator
C1 turns on the driver stage through the PWM logic block. The Nonlinear Gain block defines the amplitude of the
inductor current. The following sections describe the functionality of each individual blocks.
VOUT
L1
D1
From
Full-wave
Retifier
R3
R4
C2
R7
R1
R2
GATE
voltage
Current Loop
ISENSE
proportional to
averaged
Gate
Inductor current
Driver
Current Loop
Compensation
PWM
Comparator
ICOMP
RQ
+
+
OTA2
S
C1
-
-
PWM Logic
1.1mS +/-50μA
(linear range)
C3
Input From
Voltage Loop
S2
Nonlinear
Gain
4V
Fault
UTC 8565
Fig. 10 Complete System Current Loop
UNISONIC TECHNOLOGIES CO., LTD
9 of 13
QW-R114-004.b
www.unisonic.com.tw
8565
Preliminary
LINEAR INTEGRATED CIRCUIT
FUNCTIONAL DESCRIPTION(Cont.)
6.2 Current Loop Compensation
The compensation of the current loop is done at the ICOMP pin. This is the OTA2 output and a capacitor C3 has
to be installed at this node to ground (see Fig. 10). Under normal mode of operation, this pin gives a voltage which is
proportional to the averaged inductor current. This pin is internally shorted to 5V in the event of IC shuts down when
OLP and UVLO occur.
6.3 Pulse Width Modulation (PWM)
The IC employs an average current control scheme in continuous conduction mode (CCM) to achieve the power
factor correction.
Assuming the voltage loop is working and output voltage is kept constant, the off duty cycle DOFF for a CCM PFC
system is given as
V
IN
DOFF
=
V
OUT
From the above equation, DOFF is proportional to VIN. The objective of the current loop is to regulate the average
inductor current such that it is proportional to the off duty cycle DOFF, and thus to the input voltage VIN. Fig. 11 shows
the scheme to achieve the objective.
The PWM is performed by the intersection of a ramp signal with the averaged inductor current at pin 3 (ICOMP). The
PWM cycle starts with the Gate turn off for a duration of TOFF(MIN) (250ns typ.) and the ramp is kept discharged. The
ramp is then allowed to rise after TOFF(MIN) expires. The off time of the boost transistor ends at the intersection of the
ramp signal and the averaged current waveform. This results in the proportional relationship between the average
current and the off duty cycle DOFF
.
Fig. 12 shows the timing diagrams of TOFF(MIN) and the PWM waveforms.
6.4 Nonlinear Gain Block
The nonlinear gain block controls the amplitude of the regulated inductor current. The input of this block is the
voltage at pin VCOMP. This block has been designed to support the wide input voltage range (85-265VAC).
UNISONIC TECHNOLOGIES CO., LTD
10 of 13
QW-R114-004.b
www.unisonic.com.tw
8565
Preliminary
LINEAR INTEGRATED CIRCUIT
FUNCTIONAL DESCRIPTION(Cont.)
7. PWM Logic
The PWM logic block prioritizes the control input signals and generates the final logic signal to turn on the driver
stage. The speed of the logic gates in this block, together with the width of the reset pulse TOFF(MIN), are designed to
meet a maximum duty cycle DMAX of 95% at the GATE output under 133kHz of operation.
In case of high input currents which result in Peak Current Limitation, the GATE will be turned off immediately and
maintained in off state for the current PWM cycle. The signal TOFFMIN resets (highest priority, overriding other input
signals) both the current limit latch and the PWM on latch as illustrated in Fig. 13.
8. Voltage Loop
The voltage loop is the outer loop of the cascaded control scheme which controls the PFC output bus voltage VOUT
This loop is closed by the feedback sensing voltage at VSENSE which is a resistive divider tapping from VOUT. The pin
.
VSENSE is the input of OTA1 which has an internal reference of 5V. Fig. 14 shows the important blocks of this voltage
loop.
8.1 Voltage Loop Compensation
The compensation of the voltage loop is installed at the VCOMP pin (see Fig. 14). This is the output of OTA1 and the
compensation must be connected at this pin to ground. The compensation is also responsible for the soft start
function which controls an increasing AC input current during start-up.
VOUT
L1
D1
From
Full-wave
Retifier
R3
R4
C2
R7
Gate Driver
Current Loop
+
PWM Generation
VIN
GATE
VSENSE
-
OTA1
+
Nonlinear
Gain
Av(IIN)
5V
VCOMP
UTC 8565
R6
C4
C5
Fig. 14 Voltage Loop
UNISONIC TECHNOLOGIES CO., LTD
11 of 13
QW-R114-004.b
www.unisonic.com.tw
8565
Preliminary
LINEAR INTEGRATED CIRCUIT
FUNCTIONAL DESCRIPTION(Cont.)
8.2 Enhanced Dynamic Response
Due to the low frequency bandwidth of the voltage loop, the dynamic response is slow and in the range of about
several 10ms. This may cause additional stress to the bus capacitor and the switching transistor of the PFC in the
event of heavy load changes.
The IC provides therefore a “window detector” for the feedback voltage VVSENSE at pin 1 (VSENSE). Whenever
VVSENSE exceeds the reference value (5V) by ±5%, it will act on the nonlinear gain block which in turn affect the gate
drive duty cycle directly. This change in duty cycle is bypassing the slow changing VCOMP voltage, thus results in a
fast dynamic response of VOUT
.
9. Output Gate Driver
The output gate driver is a fast totem pole gate drive. It has an in-built cross conduction currents protection and a
Zener diode Z1 (see Fig. 15) to protect the external transistor switch against undesirable over voltages. The
maximum voltage at pin 7 (GATE) is typically clamped at 11.5V.
The output is active HIGH and at VCC voltages below the under voltage lockout threshold VCCUVLO, the gate drive is
internally pull low to maintain the off state.
TYPICAL APPLICATION CIRCUIT
VOUT
Auxiliary Supply
PFC-Controller
VCC
85...265VAC EMI-Filter
SWITCH
UTC 8565
Protection Unit
VSENSE
Voltage Loop
Compensation
PWM Logic
Driver
GATE
FREQ
Variable
Ramp
Oscillator
Generator
VCOMP
ICOMP
Nonlinear
Gain
Current Loop
Compensation
ISENSE
GND
UNISONIC TECHNOLOGIES CO., LTD
12 of 13
QW-R114-004.b
www.unisonic.com.tw
8565
Preliminary
LINEAR INTEGRATED CIRCUIT
UTC assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or
other parameters) listed in products specifications of any and all UTC products described or contained
herein. UTC products are not designed for use in life support appliances, devices or systems where
malfunction of these products can be reasonably expected to result in personal injury. Reproduction in
whole or in part is prohibited without the prior written consent of the copyright owner. The information
presented in this document does not form part of any quotation or contract, is believed to be accurate
and reliable and may be changed without notice.
UNISONIC TECHNOLOGIES CO., LTD
13 of 13
QW-R114-004.b
www.unisonic.com.tw
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明