UMD9113G-D08-T [UTC]
BRUSH DC MOTOR DRIVE CIRCUIT;型号: | UMD9113G-D08-T |
厂家: | Unisonic Technologies |
描述: | BRUSH DC MOTOR DRIVE CIRCUIT |
文件: | 总8页 (文件大小:164K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
UNISONIC TECHNOLOGIES CO., LTD
UMD9113
Preliminary
CMOS IC
BRUSH DC MOTOR DRIVE
CIRCUIT
DESCRIPTION
UTC UMD9113 is an integrated brush DC motor drive solution
for battery-powered toys, low-voltage or battery-powered motion
control applications. It has H bridge driver and uses the PMOS and
NMOS power transistors with low output resistance. Low
on-resistance ensures the circuit to consume lower power in
operating at a continuous current, and ensures the circuit to
operate stably for a long time. The circuit has a wide working
voltage range, the maximum continuous output current reaches
1.8A, and the maximum peak output current reaches 3.5A.
DIP-8
UTC UMD9113 has on-chip temperature protection function.
When load motor with low internal resistance is in locked rotor,
UTC UMD9113 output current will increase momentarily, power
dissipation of the circuit will go up sharply, and the chip
temperature will soar. But, when the chip temperature exceeds a
maximum temperature point (typically 150°C) set by internal
temperature protection circuit, the internal circuit will switch off the
on-chip power switching transistor of UTC UMD9113, and switch
off load current, preventing potential safety hazards such as
fuming, igniting, etc. Of plastic package caused by over
temperature. Only after having confirmed that the circuit has
returned to safety temperature, can the on-chip temperature
hysteresis circuit be allowed to re-control the circuit.
FEATURES
* H bridge driver of internal PMOS/NMOS power switches
* Built-in anti-common state conduction circuit.
* Low output impedance
* Low standby current (typ.0.1μA)
* Low static operational current
* On-chip thermal shut down (TSD) with hysteresis
ORDERING INFORMATION
Ordering Number
Lead Free
Package
DIP-8
Packing
Tube
Halogen Free
UMD9113G-D08-T
UMD9113L-D08-T
www.unisonic.com.tw
Copyright © 2018 Unisonic Technologies Co., Ltd
1 of 8
QW-R109-044.a
UMD9113
Preliminary
CMOS IC
MARKING
PIN CONFIGURATION
PIN DESCRIPTION
PIN NO.
PIN NAME
VCC
DESCRIPTION
1
2
3
4
5
6
7
8
Power supply of logic control circuit
INA
Forward rotation logic input
Backward rotation logic input
Power supply
INB
VDD
OUTB
AGND
PGND
OUTA
Backward rotation output
Ground of logic control circuit
Ground of output power transistor
Forward rotation output
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
2 of 8
QW-R109-044.a
UMD9113
Preliminary
CMOS IC
BLOCK DIAGRAM
VCC
1
VDD
4
VCC
Power
2
3
INA
INB
MOSFET
Driver
8
5
Level
conversion
circuit
OUTA
OUTB
AGND
LOGIC
and
TSD
PGND
VDD
VCC
Circuit
Power
Level
conversion
circuit
MOSFET
Driver
AGND
6
7
AGND
PGND
LOGIC TRUTH TABLE
INA
L
INB
OUTA
OUTB
FUNCTION
L
Z
H
L
Z
L
Standby (Stop)
Forward rotation
Backward rotation
Brake
H
L
H
H
L
H
L
H
L
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
3 of 8
QW-R109-044.a
UMD9113
Preliminary
CMOS IC
ABSOLUTE MAXIMUM RATING (TA=25°C, unless otherwise specified)
PARAMETER
SYMBOL
VCC
RATINGS
7
UNIT
V
Maximum Logic and Control Supply Voltage
Maximum Output Supply Voltage
Maximum External Output Voltage
Maximum External Input Voltage
Peak Output Current/Channel
Junction Temperature
VDD
10
V
VOUT
VIN
VDD
V
VCC
V
IOUT_PEAK
TJ
3.5
A
+150
°C
°C
°C
Operational Temperature Range
Storage Temperature
TOPR
TSTG
-20 ~ +85
-55 ~ +150
Notes: 1. Absolute maximum ratings are those values beyond which the device could be permanently damaged.
Absolute maximum ratings are stress ratings only and functional device operation is not implied.
2. Maximum power dissipation at different ambient can be obtained from the following formula
PD=(TJ-TA)/θJA.
Where TJ is junction temperature with the circuit working, and TA is the ambient temperature with the
circuit working.
3. Method of calculation of circuit power dissipation P=I2×R
Where P is circuit power dissipation, I is continuous output current, and R is circuit output on-resistance.
Circuit power dissipation P must be smaller than maximum power dissipation PD.
THERMAL DATA
PARAMETER
Junction to Ambient
SYMBOL
RATINGS
100
UNIT
°C/W
θJA
RECOMMENDED OPERATIONAL CONDITIONS (TA=25°C, unless otherwise specified)
PARAMETER
SYMBOL
VCC
RATINGS
5.0
UNIT
V
Maximum Logic and Control Supply Voltage
Maximum Output Supply Voltage
VDD
7.0
V
Note: Logic control power supply VCC and power supply VDD are fully separate internally, and can supply electricity
separately.
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
4 of 8
QW-R109-044.a
UMD9113
Preliminary
CMOS IC
ELECTRICAL CHARACTERISTICS (TA=25°C, VCC=3V, VDD=6V, unless otherwise stated)
PARAMETER SYMBOL TEST CONDITIONS MIN TYP MAX UNIT
THE POWER SUPPLY PARAMETERS
VCC Standby Current
IVCCST
IVDDST
IVCC
INA=INB=L, VCC=7V
DD=10V, Output opened
0.1
0.1
300
83
10
10
μA
μA
μA
μA
V
VDD Standby Current
VCC Static Supply Current
VDD Static Supply Current
Input Logic Level
INA=H or INB=H: Output opened
INA=H or INB=H; Output opened
IVDD
Input High Level
VINH
VINL
VHYS
IINH
2
V
V
Input Low Level
0.8
Input Level Hysteresis
Input High Level Current
Input the Pull-Down Resistor
0.6
191
15
V
VINH=2.5V, VCC=3V
VINH=3V, VCC=3V
μA
kΩ
RIN
THE POWER TUBE LEADS TO INTERNAL RESISTANCE
IO=±200mA, VDD=6V, TA=25°C
0.28
0.38
Ω
Ω
Output Resistance
RON
IO=±1800mA, VDD=6.5V, TA=25°C
PROTECTION FUNCTION PARAMETERS
Protection Temperature
TSD Hysteresis
TSD
TSDH
150
20
°C
°C
POWER MOSFET BODY DIODE CONDUCTION CHARACTERISTICS
PMOS Body Diode
VPD
VND
I=400mA,VCC=3V,VDD=INA=INB=0V
I=-400mA,VCC=VDD=3V, INA=INB=0V
0.76
0.75
V
V
NMOS Body Diode
MOTOR DRIVE TIME PARAMETERS
Output Rise Time
VCC=5V, VDD=5V, INB=H, INA input
pulse signal; The signal duty ratio is
50% and the signal frequency is
20KHz; Load motor internal resistance
is 1.3Ω, motor idling.
tr
tf
250
35
ns
ns
ns
ns
Output Fall Time
Output Delay Time
Output Delay Time
trf
tfr
100
220
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
5 of 8
QW-R109-044.a
UMD9113
Preliminary
CMOS IC
TYPICAL WAVEFORM
Forward
H
Backward
L
Brake Standby
H
L
INA
INB
Input signal
L
L
H
H
VDD
0
Output voltage
(VOUTa-VOUTb
)
-VDD
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
6 of 8
QW-R109-044.a
UMD9113
Preliminary
CMOS IC
APPLICATION INFORMATION
1. Baseline Mode
a) Standby mode
In standby mode, INA=INB=L. All internal circuits, including the drive power tube, are off state. Circuit
consumption is extremely low. In this mode, OUTA and OUTB both are in high-impedance state.
b) Forward mode
The forward mode is defined as: INA=H, INB=L, at this point the motor drive end OUTA outputs high level, and
the motor drive end OUTB outputs low level, then the motor drives the current into the motor from the OUTA, and out
from the OUTB to the ground. This motor rotation mode is defined as the forward mode.
c) Backward mode
The backward mode is defined as: INA=L, INB=H, at this point the motor drive end OUTB outputs high level,
and the motor drive end OUTA outputs low level, then the motor drives the current into the motor from the OUTB,
and out from the OUTA to the ground. This motor rotation mode is defined as the backward mode.
d) Brake mode
The brake mode is defined as: INA=H, INB=H, at this point motor drive ends OUTA and OUTB both output low
level, and the energy stored in the motor will be quickly released through the OUTA end’s NMOS tube or the OUTB
end’s NMOS tube, so the motor will stop turning in a short time.
Note: in brake mode, circuit will consume static power.
VDD
VDD
OFF
ON
OFF
OFF
OFF
OFF
ON
M
M
OFF
a) Standby mode
VDD
b) Forward mode
VDD
OFF
ON
ON
OFF
ON
OFF
ON
M
M
OFF
c) Backward mode
d) Brake mode
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
7 of 8
QW-R109-044.a
UMD9113
Preliminary
CMOS IC
TYPICAL APPLICATION CIRCUIT
UTC assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other
parameters) listed in products specifications of any and all UTC products described or contained herein.
UTC products are not designed for use in life support appliances, devices or systems where malfunction
of these products can be reasonably expected to result in personal injury. Reproduction in whole or in
part is prohibited without the prior written consent of the copyright owner. UTC reserves the right to
make changes to information published in this document, including without limitation specifications and
product descriptions, at any time and without notice. This document supersedes and replaces all
information supplied prior to the publication hereof.
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
8 of 8
QW-R109-044.a
相关型号:
©2020 ICPDF网 联系我们和版权申明