UTCTA31002A [UTC]
TELEPHONE TONE RINGER; 电话音调振铃
| 型号： | UTCTA31002A |
| 厂家： | 
Unisonic Technologies |
| 描述： | TELEPHONE TONE RINGER |
| 文件： | 总4页 (文件大小：37K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
UTC TA31002A LINEAR INTEGRATED CIRCUIT
TELEPHONE TONE RINGER
DESCRIPTION
The UTC TA31002A is a bipolar integrated circuit
designed for telephone bell replacement. It can also be
used as alarms or other alerting devices.
FEATURES
*Designed for telephone bell replacement.
*Low current drain for multiple extension of lines.
*Adjustable 2-frequency tone.
*Adjustable warbling rate.
*Built-in hysteresis prevents false triggering and
rotary dial 'CHIRPS'.
*Programmable for initiation current by simple
external resistor
DIP-8
PIN CONFIGURATIONS
Vcc
Output
1
2
3
4
8
7
6
5
High Freq.
Time Constant
RSL
Low Freq.
Time Constant
High Freq.
Time Constant
Low Freq.
Time Costant
GND
ABSOLUTE MAXIMUM RATINGS(Ta=25°C )
PARAMETER
Supply Voltage
SYMBOL
Vcc
VALUE
30
400
-45 to 85
-65 to 150
UNIT
V
mW
°C
Power Dissipation
Pd
Operating Temperature
Storage Temperature
Topr
Tstg
°C
1
UTC UNISONIC TECHNOLOGIES CO., LTD.
UTC TA31002A LINEAR INTEGRATED CIRCUIT
BLOCK DIAGRAM
R2
R3
C3
4
7
6
HIGH
OSC
AMP
8
OUTPUT
LOW
OSC
3
1
C2
POWER SUPPLY (WITH HYSTERESIS)
5
2
Note:R2,R3,C2 and C3 are parts externally mounted
ELECTRICAL CHARACTERISTICS( Ta=25°C, all voltage referenced to GND unless otherwise specified)
PARAMETER
SYMBOL
Vcc
TEST CONDITIONS
MIN
TYP MAX UNIT
Operating Supply Voltage
Initiation Supply Voltage (note 1)
Initiation Supply Current (note 1)
Sustaining Voltage (note 2)
Sustaining Current (note 2)
Output Voltage High
29.0
V
Vsi
Isi
Vsus
Isus
VOH
See Fig.2
6.8K-Pin 2 to GND
See Fig.2
17
1.4
9.7
0.7
17.0
19
2.8
11.0
1.4
21
4.2
12.0
2.5
21.0
V
mA
V
mA
V
No Load Vcc=Vsus,See Fig.2
Vcc=21V, I8=-15mA
Pin6=6V, Pin7=GND
Vcc=21V, I8=15mA
Pin6=GND, Pin7=6V
Pin3=6V, Pin4=GND
Pin7=6V, Pin6=GND
R3=191K, C3=6800pF
R3=191K, C3=6800pF
19.0
Output Voltage Low
VOL
1.6
V
IIN(Pin 3)
IIN(Pin 7)
High Frequency 1
High Frequency 2
Low Frequency
500
500
563
704
11.0
nA
nA
Hz
Hz
Hz
FH1
FH2
FL
461
576
9.0
512
640
10
R2=165K, C2=0.47mF
*NOTE (See electrical characteristics sheet)
1. Initiation supply voltage (Vsi) is the supply voltage required to start the tone ringer oscillating.
2. Sustaining voltage (Vsus) is the supply voltage required to maintain oscillation.
2
UTC UNISONIC TECHNOLOGIES CO., LTD.
UTC TA31002A LINEAR INTEGRATED CIRCUIT
APPLICATION NOTE
shows the I-V characteristic for UTC TA31002A
tone ringer. Curve A is a plot with RSL<6.8KW
and shows an increase in the current drawn up to the
initiation voltage Vsi. The I-V characteristic after
The application circuit illustrates the use of the
UTCTA31002A device in typical telephone tone ringer
application.
The AC ringer signal voltage appears
across the TIP and RING inputs of the circuit and
is attenua-
ted by capacitor C1 and resistor R1.
C1 also provides isolation from DC voltage (48V)
on the exchanged line.
initiation remains unchanged. Curve C illustrates the
effect of increasing
RSL above 6.8K
initiation current decreases but again current
alter triggering is unchanged.
After full wave rectification by the bridge
diode, the wave form is filtered by capacitor C4 to
provide a DC supply for the tone ringer chip.
As this voltage exceeds the initiation voltage (Vsi),
oscillation starts.
With the components shown , the output frequency
chops between 512Hz (FH1) and 640 Hz(FH2)
at a 10 Hz(FL) rate.
The loudspeaker load is coupled through a 1300W
to 8W transformer.
The output coupling capacitor C5 is required with
transformer coupled loads.
When driving a pizeo-ceramic transducer type load,
the coupling C5 and transformer (1300W:8W) are
not required.
However, a current limiting resistor is required.
The low frequency oscillator oscillates at a rate (FL)
controlled by an external resistor (R2) and capacitor
(C2).
The fequency can be determined using the relation
FL=1/1.289 R2* C2. The high frequency oscillates
at a FH1,FH2 controlled by an external resistor (R3)
and capacitor (C3). The frequency can be determined
using the relation FH1=1/1.504 R3*C3 and FH2=
1/1.203 R3*C3.
Pin 2 of the UTC TA31002A allows connection of
external resistor RSL, which is used to program the
slope of the supply current vs. supply voltage
characteristics (see Fig.3), and hence the supply
current up to the initiation voltage (Vsi). This initiation
voltage remains constant independent of RSL.
The supply current drawn prior to triggering varies
inversely with RSL, decreasing for increasing value
of resistance. Thus, increasing the value of RSL, will
decrease the amount of AC ringing current required to
trigger the device. As such, longer sucribser loops are
possible since less voltage is dropped per unit length of
loop wire due to the lower current level. RSL can
also be used to compensated for smaller AC coupling
capacitors (C5 on Fig.4) (higher impedance) to the
line which can be used to alter the ringer
equivalence
number of a tone ringer circuit.
The graph in Fig.3 illustrates the variation of supply
current with supply voltage of the
UTC
TA31002A.
Three curves are drawn to show the variation of
initiation current with RSL. Curve B ( RSL=6.8K)
3
UTC UNISONIC TECHNOLOGIES CO., LTD.
UTC TA31002A LINEAR INTEGRATED CIRCUIT
Circuit Current-Supply Voltage
(No Load)
Supply Current Vs. Supply Voltage
(No Load)
8.5
7.5
6.5
5.5
4.5
3.5
2.5
1.5
0.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
A:RSL=5K
B:RSL=6.8K
C:RSL=13K
2
6
10
14
18
22
26
30
34
2
6
10
14
18
22
26
30
34
Vcc(V),Supply voltage
Vcc(V),Supply voltage
Fig.2
Fig. 3
APPLICATION CIRCUIT
TIP
C1
0.9 mF
R1
560
W
C5 0.22
mF
1
8
10k
7
6
5
2
3
4
5.6k - 1 M
UTC
TA31002A
R3
191k+-1%
RING
C3
6.9nF+-5%
C4
22 F/35V
SP
R2
m
D1
29V
165k+-1%
15k
C2
0.47
mF+-5%
1300:8
W
Fig.4
4
UTC UNISONIC TECHNOLOGIES CO., LTD.
相关型号：
©2020 ICPDF网 联系我们和版权申明