V23990-P705-F [VINCOTECH]
power flow through for simple PCB routing;
| 型号： | V23990-P705-F |
| 厂家： | 
VINCOTECH |
| 描述： | power flow through for simple PCB routing PC |
| 文件： | 总3页 (文件大小：508K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Standard Power Integrated Module
flow90PACK1
Features:
flow90PACK 1 up to 600V/75A, 1200V/35A
ꢀ 3 ~ IGBT inverter
ꢀ Temperature Sensor
ꢀ Vincotech - power flow through for simple PCB routing
ꢀ Vincotech - Clip In the reliable interconnection between PCB, module and
heatsink ꢀ 600V trench fieldstop
ꢀ 1,2kV trench Fieldstop
Dedicated for motor drive applications with a mechanic arrangement of
90° between heat-sink and PCB
Module Types
selection data:
600V Trench-Fieldstop
600V / 30A
600V / 50A
600V / 75A
Vincotech part number
V23990-P704-F
V23990-P705-F
V23990-P706-F
1200V Trench-Fieldstop
1200V / 15A
V23990-P708-F
V23990-P709-F
V23990-P700-F
1200V / 25A
1200V / 35A
Copyright by Vincotech
1
Revision: 1
V23990-P70X-A
flow90PACK1
V23990-P70X-F-U-01-14
Outline / Pinout
Schematics
Copyright by Vincotech
2
Revision: 1
V23990-P70X-A
flow90PACK1
V23990-P70X-F-U-01-14
Handling Instruction
Handling Instructions...
… to the PCB
ꢀ The module must be fixed to the PCB by clipping into the adequate holes before pin soldering. See
below
ꢀ After fixing all pins must be soldered into the PCB.
ꢀ During assembly, at a max. module temperature of 25°C, the pins should not be drawn or pushed
more than ±0.2 mm or loaded with a higher force than 35N.
ꢀ At a maximum substrate-temperature of 100°C the load of the pin should not exceed ±5N.
ꢀ Vibration stress on pins is not allowed
...to the heat sink
ꢀ
ꢀ
ꢀ
the heat sink surface must be clean and particle less.
the flatness must be < 0.05 mm for 100 mm continuous.
the surface roughness should be less than
RZ = 0.01 mm.
...to the thermal paste
ꢀ
homogenous applying of the thermal conducting paste over the whole module plate with a
thickness of max. 0.05 mm.
ꢀ
Thicker thermal paste can raise the value of the Rth.
...to the fastening screws to the heat sink if plain washer is used and optional with a spring lock
washer
Important parameter
screw
M4 DIN 7985
flat washer
spring washer
mounting torque
DIN 125 or DIN 433
DIN 127 or DIN 128
Ma =2.0-2.2Nm
Copyright by Vincotech
3
Revision: 1
相关型号：
V23990-P705-F-PM
Easy paralleling;Low turn-off losses;Low collector emitter saturation voltage;Positive temperature coefficient;Short tail current
VINCOTECH
V23990-P706-F-PM
Easy paralleling;Low turn-off losses;Low collector emitter saturation voltage;Positive temperature coefficient;Short tail current
VINCOTECH
©2020 ICPDF网 联系我们和版权申明