592D476X96R3A8W_技术文档

592D

Vishay Sprague

Solid Tantalum Chip Capacitors

®

TANTAMOUNT , Low Profile, Conformal Coated,

Maximum CV

FEATURES

• New extended range offerings.

• 1.0mm to 2.5mm height.

• Terminations: Lead (Pb)-free (2) standard.

• Low Impedance

• 8mm, 12mm and 24mm tape and reel packaging

available per EIA-481-1 and reeling per IEC 286-3. 7”

[178mm] standard.

13” [330mm] available.

• Case code compatibility with EIA 535BAAC and

CECC 30801 molded chips.

PERFORMANCE CHARACTERISTICS

Capacitance Range: 1.0µF to 3300µF

Capacitance Tolerance: ±10%, ±20% standard.

Voltage Rating: 4 WVDC to 35 WVDC

Operating Temperature: - 55°C to + 85°C. (To + 125°C

with voltage derating.)

ORDERING INFORMATION

592D

106

X0

T

010

B

2

TYPE

CAPACITANCE

TOLERANCE

REEL SIZE AND

PACKAGING

DC VOLTAGE RATING CASE CODE

TERMINATION

@ + 85°C

This is expressed in

This is expressed in volts. To

complete the three-digit block,

zeros precede the voltage rating.

A decimal point is indicated by

an "R" (6R3 = 6.3 volts).

2 = 100% Tin

See Ratings

and Case

Codes Table.

T = Tape and Reel

7" [178mm] Reel

W = 13” [330mm] Reel

X0 = ±20%

X9 = ± 10%

picofarads. The first two

digits are the significant

figures. The third is the

number of zeros to follow.

4 = Gold Plated

8 = Solder plated

60/40 special

order

Note: Preferred Tolerance and reel sizes are in bold.

We reserve the right to supply higher voltage ratings and tighter capacitance tolerance capacitors in the same case size.

Voltage substitutions will be marked with the higher voltage rating.

DIMENSIONS in inches [millimeters]

W

Tantalum Wire Nib

Identifies Anode

(+) Terminal

L

B

J

D

A

H

CASE CODE

L (Max.)

0.146

[3.7]

0.158

[4.0]

0.281

[7.1]

0.298

[7.5]

0.285

[7.2]

0.126 ± 0.012

[3.2 ± 0.3]

0.158

[4.0]

W

H

A

B

D (Ref.)

0.115

[2.9]

0.139

[3.5]

0.238

[6.0]

0.254

[6.4]

0.246

[6.2]

0.087

[2.2]

0.139

[3.5]

0.238

[6.0]

0.254

[6.4]

0.246

[6.2]

0.524

[13.2]

0.524

[13.2]

J (Max.)

0.004

[0.1]

0.004

[0.1]

0.004

[0.1]

0.004

[0.1]

0.004

[0.1]

0.004

[0.1]

0.004

[0.1]

0.004

[0.1]

0.004

[0.1]

0.004

[0.1]

0.004

[0.1]

0.004

[0.1]

0.072 ± 0.012

[1.8 ± 0.3]

0.110 + 0.012-0.016 0.047 ± 0.012

[2.8 + 0.3-0.4]

0.126 ± 0.012

[3.2 ± 0.3]

0.170 ± 0.012

[4.3 ± 0.3]

0.235 ± 0.012

[6.0 ± 0.3]

0.063 ± 0.012

[1.6 ± 0.3]

0.116 ± 0.012

[2.8 ± 0.3]

0.126 ± 0.012

[3.2 ± 0.3]

0.048 ± 0.012

[1.2 ± 0.3]

0.031 ± 0.012

[0.80 ± 0.30]

0.031 ± 0.012

[0.80 ± 0.30]

0.051 ± 0.012

[1.3 ± 0.30]

0.051 ± 0.012

[1.3 ± 0.30]

0.051 ± 0.012

[1.3 ± 0.30]

0.031 ± 0.012

[0.8 ± 0.3]

0.031 ± 0.012

[0.8 ± 0.3]

0.051 ± 0.012

[1.3 ± 0.3]

0.051 ± 0.012

[1.3 ± 0.3]

0.051 ± 0.012

[1.3 ± 0.3]

0.087 ± 0.016

[2.2 ± 0.4]

0.097 ± 0.016

[2.5 ± 0.4]

0.180 ± 0.024

[4.4 ± 0.6]

0.180 ± 0.024

[4.6 ± 0.6]

0.180 ± 0.024

[4.6 ± 0.6]

0.079 ± 0.012

[2.0 ± 0.3]

0.097 ± 0.016

[2.5 ± 0.4]

0.180 ± 0.024

[4.6 ± 0.6]

0.180 ± 0.024

[4.6 ± 0.6]

A

B

C

D

R

S

T

[1.2 ± 0.3]

0.047 ± 0.012

[1.2 ± 0.3]

0.047 ± 0.012

[1.2 ± 0.3]

0.047 ± 0.012

[1.2 ± 0.3]

0.040 ± 0.012

[1.0 ± 0.3]

0.079

[2.0] Max.

0.079

0.281

[7.1]

0.298

[7.5]

0.285

[7.2]

0.575

[14.5]

0.575

[14.5]

U

V

W

X

Y

[2.0] Max.

0.079

0.170 ± 0.012

[4.3 ± 0.3]

[2.0] Max.

0.079

0.235 ± 0.012

[6.0 ± 0.3]

0.290 ± 0.010

[7.37 ± 0.25]

0.290 ± 0.010

[7.37 ± 0.25]

0.180 ± 0.024

[4.6 ± 0.6]

0.470 ± 0.024

[11.9 ± 0.6]

0.470 ± 0.024

[11.9 ± 0.6]

[2.0] Max.

0.079

0.050 ± 0.016

[1.3 ± 0.4]

0.051 ± 0.016

[1.3 ± 0.4]

[2.0] Max.

0.098

[2.5] Max.

Note: The anode termination (D less B) will be a minimum of 0.012" [0.3mm].

www.vishay.com

74

Document Number 40004

Revision 03-Dec-04

For technical questions, contact tantalum@vishay.com

592D

Vishay Sprague

RATINGS AND CASE CODES

µF

4 V

6.3 V

10 V

STD

16 V

STD

20 V

25 V

35 V

EXT

STD

EXT

STD

EXT

STD

EXT

STD

EXT

STD

B

1

A

1.5

2.2

3.3

4.7

6.8

10

15

22

33

47

B

C

D

R

B

C

D

R

A

B

B*

C

A

B

B*

C

C/D

R/T*

C*

B

C

D

R

A

B

C

D

R

B

C

D

D/T

R/T

U

V

W

C

B/D

R

D

R

B

A

B

A

A/B

A/S

U*

U*/V*

B

A

B

B*

C

D/T*

R/T

D/R/U*

D/U

V

B

C

D

C/T

R

U

R/U*/T

V*

B/C

C/D

D/T/R

D/R

D/U

V

C

D

R/T

D/R

U/V

V

A/B

68

B/C

C/D

C/T

R

R/U

D/U/V

V/W

W

B/C

B/C/T

R

D/R/U

R/U/V

V/U/W

W

X/W

X/Y

X/Y*

Y

R

100

150

220

330

470

680

1000

1500

2200

3300

C*/D/U

D

V

V/W

W

X

X/Y

* Contact factory for availability

STANDARD / EXTENDED RATINGS

Max. DF

@ + 25°C

120 Hz

(%)

Max. ESR

@ + 25°C

100kHz

Max. RIPPLE

100kHz

Irms

Max. DCL

CAPACITANCE

CASE

CODE

@ + 25°C

(µF)

PART NUMBER

(µA)

(Ohms)

(Amps)

4 WVDC @ + 85°C, SURGE = 5.2 V . . . 2.7 WVDC @ + 125°C, SURGE = 3.4 V

22

33

47*

47

68

A

B

592D226X_004A2T

592D226X_004B2T

592D336X_004B2T

592D476X_004B2T*

592D476X_004C2T

592D686X_004B2T

592D686X_004C2T

592D686X_004D2T

592D107X_004C2T

592D107X_004D2T

592D107X_004R2T

592D107X_004T2T

592D157X_004C2T

592D157X_004D2T

592D157X_004R2T

592D157X_004T2T

592D227X_004R2T

592D227X_004V2T

592D227X_004U2T

592D337X_004R2T

592D337X_004U2T

592D337X_004V2T

592D477X_004D2T

592D477X_004U2T

592D477X_004V2T

592D477X_004W2T

592D687X_004V2T

592D687X_004W2T

592D108X_004W2T

592D158X_004X2T

592D228X_004Y2T

592D228X_004X2T

0.9

1.3

1.9*

1.9

2.7

4

6

6*

6

8

10

12

14

20

25

2.40

1.60

1.5*

0.16

0.22

0.23*

0.5

B

B*

C

B

C

D

C

D

R

T

C

D

R

T

R

V

U

R

U

V

D

U

V

W

V

W

X

0.40

1.40

0.35

0.27

0.35

0.26

0.20

0.45

0.36

0.25

0.20

0.45

0.20

0.19

0.18

0.15

0.12

0.14

0.10

0.200

0.04

0.55

0.24

0.53

0.68

0.53

0.69

0.87

0.42

0.52

0.71

0.87

0.42

0.87

0.78

0.76

0.91

0.86

1.08

0.94

1.05

1.18

1.32

1.18

1.32

0.94

2.1

68

100

150

220

330

470

680

1000

1500

2200

6

8.3

13.2

18.8

27.2

40

60

88

Y

X

2.3

*Preliminary values, contact factory for availability. For 10% tolerance, specify "9"; for 20% tolerance, change to "0". Extended range ratings are in bold print.

For technical questions, contact tantalum@vishay.com

Document Number 40004

Revision 03-Dec-04

www.vishay.com

75

592D

Vishay Sprague

STANDARD / EXTENDED RATINGS

Max. DF

@ + 25°C

120 Hz

(%)

Max. ESR

@ + 25°C

100kHz

Max. RIPPLE

100kHz

Irms

Max. DCL

@ + 25°C

(µA)

CAPACITANCE

CASE

CODE

(µF)

PART NUMBER

(Ohms)

(Amps)

6.3 WVDC @ + 85°C, SURGE = 8 V . . . 4 WVDC @ + 125°C, SURGE = 5 V

15

A

B

A

B

A

B

C

S

A

B

C

D

B

C

D

R

T

592D156X_6R3A2T

592D156X_6R3B2T

592D226X_6R3A2T

592D226X_6R3A2T13H**

592D226X_6R3B2T

592D336X_6R3A2T

592D336X_6R3B2T

592D336X_6R3C2T

592D336X_6R3S2T

592D336X_6R3S2T12H**

592D476X_6R3A2T

592D476X_6R3B2T

592D476X_6R3C2T

592D476X_6R3D2T

592D686X_6R3B2T

592D686X_6R3B2T13H**

592D686X_6R3C2T

592D686X_6R3D2T

592D686X_6R3R2T

592D686X_6R3T2T

592D107X_6R3B2T15H**

592D107X_6R3C2T

592D107X_6R3D2T

592D107X_6R3R2T

592D107X_6R3T2T

592D157X_6R3D2T

592D157X_6R3R2T

592D157X_6R3U2T

592D227X_6R3D2T

592D227X_6R3R2T

592D227X_6R3U2T

592D227X_6R3V2T

592D337X_6R3C2T16H**

592D337X_6R3R2T

592D337X_6R3U2T

592D337X_6R3V2T

592D337X_6R3W2T

592D477X_6R3U2T

592D477X_6R3V2T

592D477X_6R3W2T

592D687X_6R3R2T16H**

592D687X_6R3W2T

592D108X_6R3W2T

592D108X_6R3X2T

592D158X_6R3Y2T

592D158X_6R3X2T

592D228X_6R3Y2T*

592D228X_6R3X2T

592D338X_6R3Y2T

0.9

1.4

2.1

3

6

2.50

1.70

1.5

0.15

0.22

0.23

0.2

0.23

0.32

0.24

0.5

0.28

0.17

0.21

0.5

0.65

0.46

0.36

0.51

0.68

0.87

0.4

22

6

22

6

1.5

22

6

1.5

33

6

1.70

1.40

0.40

1.3

33

6

33

6

33

8

33

10

8

2.0

47

1.40

0.40

0.30

0.38

0.60

0.38

0.27

0.20

0.50

1.0

47

3

8

47

3

6

47

6

68

4.3

6.3

9.5

13.9

20.8

29.6

42.8

63

6

68

8

68

6

68

6

68

6

68

6

100

150

220

330

470

680

1000

1500

2200*

2200

3300

B

C

D

R

T

10

8

0.28

0.51

0.69

0.87

0.42

0.71

0.87

0.76

0.75

0.91

0.86

1.08

0.81

0.91

1.05

1.18

1.32

1.05

1.18

1.32

1.16

1.32

0.94

2.1

0.38

0.26

0.20

0.45

0.25

0.20

0.19

0.22

0.18

0.15

0.12

0.15

0.18

0.10

0.13

0.100

0.2

8

D

R

U

D

R

U

V

C

R

U

V

W

U

V

W

R

W

X

Y

X

Y*

X

Y

8

10

8

14

10

14

10

20

16

20

25

35*

35

63

0.04

0.035

0.045

0.055*

0.055

95

2.3

95

1.97

1.80*

1.80

139*

139

208

10 WVDC @ + 85°C, SURGE = 13 V . . . 7 WVDC @ + 125°C, SURGE = 8 V

10

A

B

592D106X_010A2T

592D106X_010B2T

592D226X_010B2T

592D226X_010C2T

592D336X_010C2T

592D336X_010D2T

592D336X_010T2T*

592D476X_010D2T

592D476X_010R2T

592D476X_010T2T

592D686X_010C2T

592D686X_010D2T

592D686X_010R2T

592D686X_010T2T

592D686X_010U2T*

592D107X_010D2T

592D107X_010U2T

592D107X_010R2T

592D157X_010U2T

592D157X_010V2T

592D227X_010V2T

592D227X_010W2T

592D337X_010V2T*

592D337X_010W2T

1

6

2.60

1.70

1.50

0.40

0.30

0.50*

0.27

0.20

0.50

0.40

0.27

0.20

0.45

0.25*

0.10

0.19

0.22

0.17

0.14

0.12

0.10

0.10*

0.10

0.15

0.22

0.23

0.50

0.65

0.40*

0.68

0.87

0.40

0.50

0.68

0.87

0.42

0.66*

1.11

0.76

0.83

0.80

1.00

1.08

1.32

1.18*

1.32

22

B

C

D

T*

D

R

T

2.2

3.3

3.3*

4.7

6.8

6.8*

10

6

22

6

33

6

33

33*

47

6*

6

47

6

47

6

68

C

D

R

T

6

68

6

68

6

68

6

68*

100

150

220

330*

330

U*

D

U

R

U

V

6*

8

10

8

10.0

15

8

15

8

V

22

8

W

V*

W

22

8

33*

33

8*

8

** xyH indicates maximum height in (mm), i.e., 1.5 max (H) = 15Hmm

*Preliminary values, contact factory for availability. For 10% tolerance, specify "9"; for 20% tolerance, change to "0". Extended range ratings are in bold print.

*Voltage range under development.

www.vishay.com

76

Document Number 40004

Revision 03-Dec-04

For technical questions, contact tantalum@vishay.com

592D

Vishay Sprague

STANDARD / EXTENDED RATINGS

Max. DF

@ + 25°C

120 Hz

(%)

Max. ESR

Max. RIPPLE

100kHz

Irms

Max. DCL

@ + 25°C

(µA)

@ + 25°C

100kHz

(Ohms)

CAPACITANCE

CASE

CODE

(µF)

PART NUMBER

(Amps)

16 WVDC @ + 85°C, SURGE = 20 V . . . 10 WVDC @ + 125°C, SURGE = 12 V

4.7

6.8

10

15*

15

22

33

47

68*

68

A

B

C

B*

D

C

D

T

C

D

R

T

R

T

U

C*

U

V

C*

D

U

V

592D475X_016A2T

592D685X_016A2T

592D685X_016B2T

592D106X_016B2T

592D106X_016C2T

592D156X_016B2T*

592D156X_016D2T

592D226X_016C2T

592D226X_016D2T

592D226X_016T2T

592D336X_016C2T

592D336X_016D2T

592D336X_016R2T

592D336X_016T2T

592D476X_016R2T

592D476X_016T2T

592D476X_016U2T

592D686X_016C2T*

592D686X_016U2T

592D686X_016V2T

592D107X_016C2T*

592D107X_016D2T

592D107X_016U2T

592D107X_016V2T

592D157X_016W2T

592D227X_016W2T

0.8

1.1

1.6

2.4*

2.4

3.5

5.3

7.5

10.9*

10.9

16*

16

6

6*

6

6*

6

8*

8

3.50

1.80

1.60

1.00

1.4*

0.50

0.40

0.6

0.13

0.21

0.22

0.32

0.24*

0.50

0.46

0.60

0.36

0.66

0.62

0.75

0.36

0.77

0.33

0.66

1.20*

0.66

0.91

1.80*

0.97

1.32

0.94

0.25

0.30

0.27

0.6

0.25

0.72

0.25

0.50*

0.25

0.17

0.30*

0.15

0.1

100*

100

150

220

16

24

35.2

W

0.2

20 WVDC @ + 85°C, SURGE = 26 V . . . 13 WVDC @ + 125°C, SURGE = 16 V

4.7

6.8

10

15

22

22*

33

33*

A

B

592D475X_020A2T

592D475X_020B2T

592D685X_020B2T

592D685X_020C2T

592D106X_020B2T

592D106X_020D2T

592D156X 020C2T

592D156X_020R2T

592D226X_020D2T

592D226X_020R2T

592D226X_020T2T

592D226X_020U2T*

592D336X_020R2T

592D336X_020V2T*

0.9

1.4

2

3

4.4

4.4*

6.6

6.6*

6

6*

6

6*

3.80

3.20

3.10

1.10

3.00

0.50

0.60

0.40

0.28

0.60

0.30*

0.28

0.26*

0.13

0.16

0.30

0.16

0.48

0.42

0.65

0.56

0.73

0.37

0.61*

0.73

0.73*

B

C

B

D

C

R

D

R

T

U*

R

V*

25 WVDC @ + 85°C, SURGE = 33 V . . . 17 WVDC @ + 125°C, SURGE = 20 V

2.2

3.3

4.7

6.8

10

15

15*

22*

68

A

B

C

D

B

D

R

U*

V*

R

592D225X_025A2T

592D225X_025B2T

592D335X_025B2T

592D335X_025C2T

592D475X_025C2T

592D685X_025C2T

592D685X_025D2T

592D106X_025B2T

592D106X_025D2T

592D106X_025R2T

592D156X_025R2T

592D156X_025U2T*

592D226X_025U2T*

592D226X_025V2T*

592D686X_025R2T20H

0.6

0.8

1.2

1.7

2.5

3.8

3.8*

5.5*

17

6

6*

8

8.00

6.00

5.60

2.00

1.60

1.50

1.30

2.00

1.20

0.48

0.40

0.40*

0.30*

0.23

0.09

0.12

0.22

0.25

0.26

0.31

0.115

0.32

0.56

0.61

0.52*

0.68*

0.87

*Preliminary values, contact factory for availability. For 10% tolerance, specify "9"; for 20% tolerance, change to "0". Extended range ratings are in bold print.

*Voltage range under development.

For technical questions, contact tantalum@vishay.com

Document Number 40004

Revision 03-Dec-04

www.vishay.com

77

592D

Vishay Sprague

STANDARD / EXTENDED RATINGS

Max. DF

@ + 25°C

120 Hz

(%)

Max. ESR

@ + 25°C

100kHz

Max. RIPPLE

100kHz

Irms

Max. DCL

@ + 25°C

(µA)

CAPACITANCE

CASE

CODE

(µF)

PART NUMBER

(Ohms)

(Amps)

35 WVDC @ + 85°C, SURGE = 46 V . . . 23 WVDC @ + 125°C, SURGE = 28 V

1

A

B

592D105X_035A2T

592D105X_035B2T

592D155X_035B2T

592D225X_035B2T*

592D225X_035C2T

592D335X_035C2T

592D335X_035D2T

592 D475X_035R2T

592 D685X_035D2T

592D685X_035R2T

592D106X_035R2T

0.5

0.8*

0.8

1.2

1.6

2.4

3.5

4

6*

6

10.0

6.50

4.2

0.08

0.11

0.14

0.12*

0.17

0.18

0.24

0.34

0.31

0.35

1

1.5

2.2*

2.2

3.3

4.7

6.8

10

B

B*

C

D

R

D

R

6.00*

3.50

3.20

2.10

1.30

1.20

TYPICAL CURVES OF ESR - AS A FUNCTION OF FREQUENCY

"B" Case

"A" Case

IMPEDANCE

1000

100

10

1000

100

10

IMPEDANCE

ESR

4.7µF, 20 V

1µF, 35

15µF, 6.3

1

10µF, 10 V

100

1K

10K

100K

100

1K

10K

100K

1M

0.1

FREQUENCY IN HERTZ

"D" Case

"C" Case

1000

100

10

100

10

IMPEDANCE

ESR

IMPEDANCE

ESR

1

6.8µF, 25 V

4.7µF, 25 V

1

0.1

0.01

47µF, 6.3 V

33µF, 6.3 V

100

0.1

1K

10K

100K

1M

100

1K

10K

FREQUENCY IN HERTZ

100K

1M

FREQUENCY IN HERTZ

www.vishay.com

78

Document Number 40004

Revision 03-Dec-04

For technical questions, contact tantalum@vishay.com

592D

Vishay Sprague

TYPICAL CURVES @ + 25°C, IMPEDANCE AND ESR VS FREQUENCY

"R" Case

"S" Case

100

10

100

10

IMPEDANCE

ESR

IMPEDANCE

ESR

33 - 6.3V

1

10µF, 25 V

0.1

100µF, 6.3 V

1K

0.01

100

0.01

100

10K

100K

1M

1000

10000

100000

1000000

FREQUENCY IN HERTZ

592D 1500-4V X CASE ESR/IMPEDANCE VS FREQUENCY

592D 1500-6.3V Y CASE ESR/IMPEDANCE VS FREQUENCY

10

10.00

ESR

IMPEDANCE

1

1.00

0.10

0.01

0.1

0.01

100

1kHz

10kHz

100kHz

1MHz

10MHz

100

1kHz

10kHz

100kHz

1MHz

10MHz

FREQUENCY (Hz)

592D 1000-6.3V X CASE ESR/IMPEDANCE VS FREQUENCY

592D 2200-4V Y CASE ESR/IMPEDANCE VS FREQUENCY

10.00

1.00

0.10

0.01

10.00

1.00

0.10

0.01

ESR

IMPEDANCE

100

1kHz

10kHz

100kHz

1MHz

10MHz

100

1kHz

10kHz

100kHz

1MHz

10MHz

FREQUENCY (Hz)

For technical questions, contact tantalum@vishay.com

Document Number 40004

Revision 03-Dec-04

www.vishay.com

79

592D

Vishay Sprague

PERFORMANCE CHARACTERISTICS

1.

Operating Temperature: Capacitors are designed to

operate over the temperature range - 55°C to + 85°C.

- 55°C

- 10%

+ 85°C

+ 10%

+ 125°C

+ 12%

1.1

Capacitors may be operated to + 125°C with

voltage derating to two-thirds the + 85°C rating.

6.

Dissipation Factor: The dissipation factor,

determined from the expression 2πfRC, shall not

exceed values listed in the Standard Ratings Table.

+ 85°C Rating

+ 125°C Rating

Working

Voltage

(V)

Surge

Voltage

(V)

Working

Voltage

(V)

Surge

Voltage

(V)

6.1

7.

Measurements shall be made by the bridge method

at, or referred to, a frequency of 120 Hz and a

temperature of + 25°C.

4

5.2

8

2.7

4

7

10

13

17

23

3.4

5

8

12

16

20

28

6.3

10

16

20

25

35

13

20

26

32

46

Leakage Current: Capacitors shall be stabilized at

the rated temperature for 30 minutes. Rated voltage

shall be applied to capacitors for 5 minutes using a

steady source of power (such as a regulated power

supply) with 1000 ohm resistor connected in series

with the capacitor under test to limit the charging

current. Leakage current shall then be measured.

2.

3.

DC Working Voltage: The DC working voltage is the

maximum operating voltage for continuous duty at the

rated temperature.

Note that the leakage current varies with temperature

and applied voltage. See graph below for the

appropriate adjustment factor.

Surge Voltage: The surge DC rating is the maximum

voltage to which the capacitors may be subjected

under any conditions, including transients and peak

ripple at the highest line voltage. 592D228X_6R3X2T

and 592D338X_6R3V2T, not surge voltage tesed.

TYPICAL LEAKAGE CURRENT FACTOR RANGE

3.1

3.2

Surge Voltage Test: Capacitors shall withstand

the surge voltage applied in series with a 33 ohm

± 5% resistor at the rate of one-half minute on,

one-half minute off, at + 85°C, for 1000 successive

test cycles.

100

+ 125°C

+ 85°C

10

Following the surge voltage test, the dissipation

factor and the leakage current shall meet the initial

requirements;thecapacitanceshallnothavechanged

more than ± 10%.

+ 55°C

+ 25°C

1.0

4.

Capacitance Tolerance: The capacitance of all

capacitors shall be within the specified tolerance

limits of the normal rating.

0°C

4.1

Capacitance measurements shall be made by means

of polarized capacitance bridge. The polarizing

voltage shall be of such magnitude that there shall be

no reversal of polarity due to the AC component. The

maximum voltage applied to capacitors during

measurement shall be 2 volts rms at 120 Hz at +25°C.

If the AC voltage applied is less than one-half volt rms,

no DC bias is required. Accuracy of the bridge shall

be within ± 2%.

0.1

- 55°C

0.01

5.

Capacitance Change With Temperature: The

capacitancechangewithtemperatureshallnotexceed

thefollowingpercentageofthecapacitancemeasured

at + 25°C:

0.001

0

10 20

30 40

50 60 70 80

90 100

Percent of Rated Voltage

www.vishay.com

80

Document Number 40004

Revision 03-Dec-04

For technical questions, contact tantalum@vishay.com

592D

Vishay Sprague

PERFORMANCE CHARACTERISTICS (Continued)

12.

Resistance to Soldering Heat: Capacitors mounted

on a substrate will withstand + 260°C for 5 seconds.

7.1

7.2

7.3

8.

At + 25°C, the leakage current shall not exceed

the value listed in the Standard Ratings Table.

At + 85°C, the leakage current shall not exceed 10

times the value listed in the Standard Ratings Table.

12.1 Following the resistance to soldering heat test,

capacitance, dissipation factor and DC leakage

current shall meet the initial requirement.

At + 125°C, the leakage current shall not exceed 12

times the value listed in the Standard Ratings Table.

13.

Marking: The small body area of these capacitors

does not allow elaborate marking schemes. All

required information is present on the carton or

package in which the parts are shipped; in addition,

part number, quantity and data code are indicated on

the reels.

Equivalent Series Resistance: Measurements shall

be made by the bridge method at, or referred to, a

frequency of 100 KHz and a temperature of + 25°C.

8.1

9.

TheEquivalentSeriesResistanceshallnotexceedthe

value listed in the Standard Ratings Table.

14.

15.

Terminal Strength: Per IEC-384-3, minimum of

5N shear force.

Life Test: Capacitors shall withstand rated DC

voltage applied at + 85°C for 2000 hours or derated

DC voltage applied at + 125°C for 1000 hours.

Environmental: Mercury, CFC and ODS materials

are not used in the manufacture of these capacitors.

9.1

10

Following the life test, the dissipation factor and

leakage shall meet the initial requirement; the

capacitance change shall not exceed ± 10% of the

initial value.

16.

17.

Flammability: Encapsulant materials meet UL94 V0

Capacitor Failure Mode: The predominant failure

mode for solid tantalum capacitors is increased

leakage current resulting in a shorted circuit. Capaci-

tor failure may result from excess forward or reverse

DC voltage, surge current, ripple current, thermal

shock or excessive temperature.

HumidityTest:Capacitorsshallwithstand1000hours

at + 40°C, 90% to 95% relative humidity, with no

voltage applied

10.1 Following the humidity test, capacitance change shall

not exceed ± 10% of the initial value, dissipation factor

shall not exceed 150% of the initial requirement;

leakage currrent shall not exceed 200% of the initial

requirement at + 25°C

The increase in leakage is caused by a breakdown of

the Ta₂O₅dielectric. For additional information on

leakage failure of solid tantalum chip capacitors, refer

to Vishay Sprague Technical Paper, “Leakage Failure

Mode in Solid Tantalum Chip Capacitors.”

11.

Solderability: Capacitors will meet the solderability

requirements of ANSI/J-STD-002, test B category 1.

GUIDE TO APPLICATION

1.0

Recommended rated working voltage guidelines:

(-55°C to + 85°C)

R_ESR= The capacitor Equivalent Series Resistance

at the specified frequency.

Application Voltage

(V)

Recommended

Capacitor Voltage

Rating (V)

3.

A-C Ripple Voltage: The maximum allowable ripple

voltage shall be determined from the formula:

2.5

4

5

4

6.3

8

10

16

20

25

35

P

V_rms= Z

R_ESR

6

10

12

18

24

or, from the formula:

V_rms= I_rmsx Z

where,

2.

A-C Ripple Current: The maximum allowable ripple

current shall be determined from the formula:

P = Power Dissipation in Watts @ + 25°C as given in

the table in Paragraph Number 6.0 (Power

Dissipation).

P

R_ESR= The capacitor Equivalent Series Resistance

R_ESR

I_rms

=

at the specified frequency.

where,

Z = The capacitor impedance at the specified

frequency.

P = Power Dissipation in Watts @ + 25°C as given

in the table in Paragraph Number 6.0 (Power Dissipation)

For technical questions, contact tantalum@vishay.com

Document Number 40004

Revision 03-Dec-04

www.vishay.com

81

592D

Vishay Sprague

GUIDE TO APPLICATION (Continued)

The Soldering Profile chart shows typical recomended

time/temperature conditions for soldering. Attachment

with a soldering iron is not recommended due to the

difficulty of controlling temperature and time at

temperature. The soldering iron must never come in

contact with the capacitor.

3.1

3.2

4.0

The sum of the peak AC voltage plus the applied DC

voltage shall not exceed the DC voltage rating of the

capacitor.

The sum of the negative peak AC voltage plus the

applied DC voltage shall not allow a voltage reversal

exceeding 10% of the DC working voltage at + 25°C.

RECOMMENDED REFLOW SOLDERING PROFILE

Reverse Voltage: These capacitors are capable of

withstanding peak voltages in the reverse direction

equal to 10% of the DC rating or 1 volt maximum at

+25°C and 5% of the DC voltage rating or 0.5 volt

maximum at + 85°C.

250

200

150

100

50

5.0

Temperature Derating: If these capacitors are to be

operated at temperatures above + 25°C, the

permissible rms ripple current or voltage shall be

calculated using the derating factors as shown:

0

50

100

150

200

250

300

350

Temperature

+ 25°C

+ 85°C

+ 125°C

Derating Factor

TIME (SECONDS)

1.0

0.9

0.4

9.0 Recommended Mounting Pad Geometries: The

nib must have sufficient clearance to avoid electrical

contact with other components. The width dimension

indicated is the same as the maximum width of the

capacitor. This is to minimize lateral movement.

6.0

Power Dissipation: Power dissipation will be

affected by the heat sinking capability of the mounting

surface. Non-sinusoidal ripple current may produce

heating effects which differ from those shown. It is

important that the equivalent Irms value be

established when calculating permissible operating

levels. (Power dissipation calculated using + 25°C

temperature rise.)

REFLOW SOLDER PADS*

in inches [millimeters]

B

C

Maximum Permissible

Power Dissipation

@ + 25°C (Watts) in free air

B

Case Code

A

B

C

D

R

S

T

U

V

W

X

Y

CASE

CODE

A

WIDTH

(A)

0.082

[2.1]

0.120

[3.5]

0.130

[3.5]

0.180

[4.6)

2.45

[8.3]

0.067

[1.7]

0.120

[3.5]

0.136

[3.5]

0.180

[4.6)

0.245

[8.3]

0.310

[7.9]

PAD

METALIZATION

0.085

[1.7]

SEPARATION

(C)

0.060

0.080

0.100

0.125

0.150

0.060

0.080

0.110

0.140

0.175

0.180

0.050

[1.3]

0.065

[1.7]

0.120

[3.1]

0.145

[3.7]

0.145

[3.7]

0.043

[1.1]

0.065

[1.7]

0.120

[3.1]

0.145

[3.7]

0.145

[3.7]

0.360

[9.2]

0.360

[9.2]

B

C

D

R

S

T

0.065

[1.7]

0.080

[2.3]

0.080

[2.3]

0.090

[2.3]

0.032

[0.8]

0.065

[1.7]

0.090

[2.3]

0.090

[2.3]

7.0

Printed Circuit Board Materials: The capacitors are

compatible with most commonly used printed circuit

board materials (alumina substrates, FR4, FR5,

G10, PTFE-fluorocarbon and porcelanized steel). If

your desired board material is not shown there please

contact the Tantalum Marketing Department for

assistance in determining compatibility.

U

V

W

X

Y

0.090

[2.3]

0.120

[3.0]

0.120

[3.0]

8.

Attachment:

0.310

[7.9]

8.1

Solder Paste: The recommended thickness of the

solder paste after application is 0.007" ± .001"

[.178mm ± .025mm]. Care should be exercised in

selecting the solder paste. The metal purity should

be as high as practical. The flux (in the paste) must

be active enough to remove the oxides formed on the

metallization prior to the exposure to soldering heat.

* Pads for B, C and D case codes are otherwise pad compatible with

* Type 293D, B, C and D case codes respectively.

10.0 Cleaning (Flux Removal) After Soldering: The

592D capacitors are compatible with all commonly

used solvents such as TES, TMS, Prelete, Chlorethane,

Terpene and aqueous cleaning media. Solvents

containing methylene chloride or other epoxy solvents

should be avoided since these will attack the epoxy

encapsulation material.

8.2 Soldering: Capacitors can be attached by

conventional soldering techniques - convection,

infrared reflow, wave soldering and hot plate methods.

www.vishay.com

82

Document Number 40004

Revision 03-Dec-04

For technical questions, contact tantalum@vishay.com

592D

Vishay Sprague

TAPE AND REEL PACKAGING in inches [millimeters]

Top

Cover

Tape

Thickness

Standard orientation is with the

cathode (-) nearest to the

sprocket holes per EIA-481-1

and IEC 286-3.

Carrier

Embossment

R

Min.

Bending Radius

(Note 2)

Units Per Reel

Tape

Width

Component

7" [178]

Reel

13" [330]

Reel

Case Code

Pitch

A

B

C

D

R

S

T

8mm

12mm

8mm

4mm

8mm

4mm

8mm

12mm

2500

2000

1000

2500

2000

1000

500

10000

8000

4000

10000

8000

4000

2500

12mm

24mm

U

V

W

X

Y

500

For technical questions, contact tantalum@vishay.com

Document Number 40004

Revision 03-Dec-04

www.vishay.com

83

592D

Vishay Sprague

TAPE AND REEL PACKAGING in inches [millimeters]

Note: Metric dimensions will govern. Dimensions in inches are rounded and for reference only.

.157 ± .004

[4.0 ± 0.10]

T₂

Max.

10 Pitches Cumulative

Tolerance on Tape

± 0.008 [0.200]

Deformation

Between

Embossments

.059 + .004 - 0.0

[1.5 + 0.10 - 0.0]

Embossment

.024

[0.600]

Max.

.069 ± .004

[1.75 ± 0.10]

.079 ± .002

[2.0 ± 0.05]

Top

Cover

Tape

20°

A₀

.030 [0.75]

Min. (Note 3)

F

W

Maximum

Component

Rotation

B₁Max.

(Note 6)

B₀

K₀

.030 [0.75]

Min. (Note 4)

Top

Cover

Tape

(Side or Front Sectional View)

P₁

Center Lines

of Cavity

For Tape Feeder

Reference only

including draft.

Concentric around B₀

(Note 5)

D₁Min. For Components

.079 x .047 [2.0 x 1.2] and Larger.

.004 [0.10]

Max.

USER DIRECTION OF FEED

(Note 5)

Maximum

Cavity Size

(Note 1)

Cathode (-)

Anode (+)

DIRECTION OF FEED

20° Maximum

3.937 [100.0]

Tape and Reel Specifications: All case sizes are available

on plastic embossed tape per EIA-481-1. Tape reeling per

IEC 286-3 is also available. Standard reel diameter is 7"

[178mm]. 13" [330mm] reels are available and recommended

as the most cost effective packaging method.

Component Rotation

.039 [1.0]

Max.

Typical

Component

Cavity

Tape

B₀

Center Line

.039 [1.0] Max.

The most efficient packaging quantities are full reel increments

on a given reel diameter. The quantities shown allow for the

sealed empty pockets required to be in conformance with

EIA-481-1. Reel size and packaging orientation must be

specified in the Vishay Sprague part number.

Typical

Component

Center Line

9.843 [250.0]

Camber

(Top View)

Allowable Camber to be .039/3.937 [1/100]

Non-Cumulative Over 9.843 [250.0]

A₀

(Top View)

TAPE

SIZE

8mm

B₁(Max.)

(Note 6)

0.179

[4.55]

0.323

[8.2]

0.323

[8.2]

D₁(Min.)

R (Min.)

(Note 2)

0.984

[25.0]

1.181

[30.0]

1.181

[30.0]

1.181

[30.0]

T₂

(Max.)

0.098

[2.5]

0.256

[6.5]

0.256

[6.5]

0.103

[2.6]

A₀B₀K₀

(Note 5)

0.039

[1.0]

0.059

[1.5]

0.059

[1.5]

0.059

[1.5]

F

P₁

W

0.315 + .012 - .004

[8.0 + 0.3 - 0.1]

0.472 ± 0.012

[12.0 ± 0.30]

0.472 ± 0.012

[12.0 ± 0.30]

0.945 ± 0.012

[24.0 ± 0.03]

0.138 ± 0.002

[3.5 ± 0.05]

0.217 ± 0.002

[5.5 ± 0.05]

0.217 ± 0.002

[5.5 ± 0.05]

0.453 ± 0.04

[11.5 ± 0.03]

0.157 ± 0.004

[4.0 ± 0.10]

0.157 ± 0.004

[4.0 ± 0.10]

0.315 ± 0.004

[8.0 ± 0.10]

0.472 ± 0.004

[12.0 ± 0.10]

(Note 1)

12mm

Double Pitch

24mm

0.791

[20.1]

Notes:

1. A₀B₀K are determined by the maximum dimensions to the ends of the terminals extending from the component body and/or the body

dimen⁰sions of the component. The clearance between the ends of the terminals or body of the component to the sides and depth of the

cavity (A₀B₀K₀) must be within .002" [0.05mm] minimum and .020" [0.50mm] maximum. The clearance allowed must also prevent

rotation of the component within the cavity of not more than 20 degrees.

2. Tape with components shall pass around radius "R" without damage. The minimum trailer length may require additional length to

provide R minimum for 12mm embossed tape for reels with hub diameters approaching N minimum.

3. This dimension is the flat area from the edge of the sprocket hole to either the outward deformation of the carrier tape between the

embossed cavities or to the edge of the cavity whichever is less.

4. This dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the

carrier tape between the embossed cavity or to the edge of the cavity whichever is less.

5. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of

embossment location and hole location shall be applied independent of each other.

6. B₁dimension is a reference dimension for tape feeder clearance only.

www.vishay.com

84

Document Number 40004

Revision 03-Dec-04

For technical questions, contact tantalum@vishay.com


型号：	592D476X96R3A8W
厂家：	VISHAY
描述：	CAPACITOR, TANTALUM, SOLID, POLARIZED, 6.3V, 47uF, SURFACE MOUNT, 1507, CHIP
文件：	总11页 (文件大小：207K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

592D476X96R3A8W [VISHAY]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E