CRCW0201221KFNED [VISHAY]
Fixed Resistor, Metal Glaze/thick Film, 0.05W, 221000ohm, 30V, 1% +/-Tol, 200ppm/Cel, Surface Mount, 0201, CHIP;
| 型号： | CRCW0201221KFNED |
| 厂家： | 
VISHAY |
| 描述： | Fixed Resistor, Metal Glaze/thick Film, 0.05W, 221000ohm, 30V, 1% +/-Tol, 200ppm/Cel, Surface Mount, 0201, CHIP 电阻器 |
| 文件： | 总5页 (文件大小：84K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
CRCW0201 e3
www.vishay.com
Vishay
Lead (Pb)-free Commodity Thick Film Chip Resistors
FEATURES
• High volume product suitable for commercial
applications
• Pure tin solder contacts on Ni barrier layer
provides compatibility with lead (Pb)-free and
lead containing soldering processes
• Metal glaze on high quality ceramic
• Material categorization: For definitions of compliance
please see www.vishay.com/doc?99912
STANDARD ELECTRICAL SPECIFICATIONS
LIMITING
ELEMENT
VOLTAGE
Umax.
ACRMS/DC
V
CASE
SIZE
INCH
CASE
SIZE
METRIC
POWER RATING
TEMPERATURE
COEFFICIENT
ppm/K
RESISTANCE
RANGE
TOLERANCE
%
MODEL
P70
SERIES
W
200
- 200/+ 400
100
10.0 to 10M
1.0 to 9.76
47.0 to 10M
10.0 to 10M
1.0 to 9.76
10.0 to 10M
1.0 to 9.76
0.5
1
E96
E24; E96
E24
0.05
30
200
CRCW0201
0201 RR 0603M
- 200/+ 400
200
5
- 200/+ 400
Zero-Ohm-Resistor: Rmax. = 50 m, Imax. at 70 °C = 1.0 A
Notes
•
These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over
operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime.
Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material.
•
TECHNICAL SPECIFICATIONS
PARAMETER
UNIT
W
CRCW0201
Rated Dissipation at 70 °C (1)
Operating Voltage Umax. ACRMS/DC
Insulation Voltage Uins (1 min)
Insulation Resistance
0.05
30
V
V
50
> 109
Operating Temperature Range
Weight/1000 Pieces
°C
mg
- 55 to + 155
0.17
Note
(1)
The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the
printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded.
Revision: 06-Jun-12
Document Number: 20052
1
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CRCW0201 e3
www.vishay.com
Vishay
PART NUMBER AND PRODUCT DESCRIPTION
PART NUMBER: CRCW02011K00FNED
C
R
C
W
0
2
0
1
1
K
0
0
F
K
E
D
MODEL
VALUE
TOLERANCE
TCR
PACKAGING
CRCW0201
R = Decimal
K = Thousand
M = Million
D = 0.5 ꢀ
F = 1.0 ꢀ
J = 5.0 ꢀ
Z = Jumper
K = 100 ppm/K
N = 200 ppm/K
X = - 200 ppm/K/+ 400 ppm/K
0 = Jumper
ED
EE
EI
0000 = Jumper
PRODUCT DESCRIPTION: CRCW0201 100 1K0 1 % ET7 e3
CRCW0201
100
562R
1 %
ET7
e3
RESISTANCE
VALUE
TOLERANCE
VALUE
MODEL
TCR
PACKAGING
LEAD (Pb)-FREE
CRCW0201
200 ppm/K
100 ppm/K
- 200/+ 400 ppm/K
1R0 = 1
10R = 10
1K0 = 1 k
10K = 10 k
1M0 = 1 M
0R0 = Jumper
0.5 %
1 %
5 %
ET7
EF4
ET2
e3 = Pure tin
termination finish
PACKAGING
MODEL
CODE
QUANTITY
CARRIER TAPE
WIDTH
PITCH
2 mm
REEL DIAMETER
180 mm/7"
ED = ET7
EI = ET2
EE = EF4
10 000
20 000
50 000
Paper tape acc.
to IEC 60068-3
Type I
CRCW0201
8 mm
254 mm/10"
330 mm/13"
DIMENSIONS in millimeters
SIZE
DIMENSIONS
SOLDER PAD DIMENSIONS
INCH
METRIC
L
W
H
T1
T2
a
b
l
+ 0.05
- 0.10
0201
0603
0.6 0.05
0.3 0.05
0.23 0.05 0.15 0.05
0.2
0.28
0.43
0.23
Note
No marking for 0201 size.
•
Revision: 06-Jun-12
Document Number: 20052
2
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CRCW0201 e3
www.vishay.com
Vishay
DERATING
100
50
0
- 50
0
50
100
150
70
Ambient Temperature ϑamb in °C
TEST PROCEDURES AND REQUIREMENTS
IEC
60068-2
TEST
EN 60115-1
CLAUSE
REQUIREMENTS
PERMISSIBLE CHANGE (R)
TEST
PROCEDURE
METHOD
Stability for product types:
CRCW0201 e3
1 to 10 M
4.5
4.7
-
-
Resistance
-
0.5 ꢀ; 1 ꢀ; 5 ꢀ
No flashover or breakdown
Voltage proof
U = 1.4 x Uins; 60 s
Solder bath method;
Sn60Pb40
non activated flux;
(235 5) °C
Good tinning ( 95 ꢀ covered)
no visible damage
(2 0.2) s
4.13
58 (Td)
Solderability
Solder bath method;
Sn96.5Ag3Cu0.5
non-activated flux;
(245 5) °C
Good tinning ( 95 ꢀ covered)
no visible damage
(3 0.3) s
100 ppm/K,
200 ppm/K,
- 200 ppm/K/+ 400 ppm/K
(20/- 55/20) °C and
(20/125/20) °C
4.8.4.2
4.32
-
Temperature coefficient
Shear
(adhesion)
21 (Uu3)
21 (Uu1)
9 N
No visible damage
No visible damage,
no open circuit in bent position
(0.5 ꢀ R + 0.05 )
Depth 2 mm;
3 times
4.33
Substrate bending
30 min. at - 55 °C;
30 min. at 125 °C
4.19
14 (Na)
Rapid change of temperature
5 cycles
(0.5 ꢀ R + 0.05 )
(1 ꢀ R + 0.05 )
1000 cycles
Revision: 06-Jun-12
Document Number: 20052
3
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
CRCW0201 e3
www.vishay.com
Vishay
TEST PROCEDURES AND REQUIREMENTS
IEC
60068-2
TEST
EN 60115-1
CLAUSE
REQUIREMENTS
PERMISSIBLE CHANGE (R)
TEST
PROCEDURE
METHOD
Stability for product types:
CRCW0201 e3
1 to 10 M
4.23
-
Climatic sequence:
Dry heat
-
4.23.2
2 (Ba)
125 °C; 16 h
55 °C; 90 ꢀ RH;
4.23.3
30 (Db)
Damp heat, cyclic
24 h; 1 cycle
4.23.4
4.23.5
1 (Aa)
13 (M)
Cold
- 55 °C; 2 h
(2 ꢀ R + 0.1 )
Low air pressure
1 kPa; (25 10) °C; 1 h
55 °C; 90 ꢀ RH;
4.23.6
4.23.7
30 (Db)
-
Damp heat, cyclic
DC load
24 h; 5 cycles
U = P70 x R Umax.
U = P70 x R Umax.;
1.5 h on; 0.5 h off;
4.25.1
-
Endurance at 70 °C
70 °C; 1000 h
70 °C; 8000 h
(2 ꢀ R + 0.1 )
(4 ꢀ R + 0.1 )
Solder bath method
(260 5) °C;
4.18.2
4.35
58 (Td)
-
Resistance to soldering heat
Flamability, needle flame test
Damp heat, steady state
(1 ꢀ R + 0.05 )
No burning after 30 s
(2 ꢀ R + 0.1 )
(10 1) s
IEC 60695-11-5;
10 s
(40 2) °C;
(93 3) ꢀ RH;
56 days
4.24
78 (Cab)
Endurance at
upper category temperature
4.25.3
4.29
-
155 °C, 1000 h
(2 ꢀ R + 0.1 )
Isopropyl alcohol;
50 °C; method 2
45 (XA)
Component solvent resistance
No visible damage
f = 10 Hz to 2000 Hz;
x, y, z 1.5 mm;
A 200 m/s2;
Vibration, endurance
by sweeping
4.22
6 (Fc)
(0.5 ꢀ R + 0.05 )
10 sweeps per axis
All tests are carried out in accordance with the following specifications:
• EN 60115-1, generic specification
• EN 140400, sectional specification
• EN 140401-802, detail specification
• IEC 60068-2-x, environmental test procedures
Packaging of components is done in paper tapes according to IEC 60286-3.
Revision: 06-Jun-12
Document Number: 20052
4
For technical questions, contact: thickfilmchip@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
Document Number: 91000
1
相关型号：
CRCW0201221RFKED
Fixed Resistor, Metal Glaze/thick Film, 0.05W, 221ohm, 30V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0201, CHIP
VISHAY
CRCW0201221RFNED
Fixed Resistor, Metal Glaze/thick Film, 0.05W, 221ohm, 30V, 1% +/-Tol, 200ppm/Cel, Surface Mount, 0201, CHIP
VISHAY
CRCW0201223J200P0
Fixed Resistor, Metal Glaze/thick Film, 0.05W, 22000ohm, 30V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0201, CHIP
VISHAY
CRCW0201226KFNED
Fixed Resistor, Metal Glaze/thick Film, 0.05W, 226000ohm, 30V, 1% +/-Tol, 200ppm/Cel, Surface Mount, 0201, CHIP
VISHAY
CRCW0201226RFNED
Fixed Resistor, Metal Glaze/thick Film, 0.05W, 226ohm, 30V, 1% +/-Tol, 200ppm/Cel, Surface Mount, 0201, CHIP
VISHAY
CRCW020122K0FKED
Fixed Resistor, Metal Glaze/thick Film, 0.05W, 22000ohm, 30V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0201, CHIP
VISHAY
CRCW020122K0JNED
Fixed Resistor, Metal Glaze/thick Film, 0.05W, 22000ohm, 30V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0201, CHIP
VISHAY
CRCW020122K1FKED
Fixed Resistor, Metal Glaze/thick Film, 0.05W, 22100ohm, 30V, 1% +/-Tol, 100ppm/Cel, Surface Mount, 0201, CHIP
VISHAY
CRCW020122K1FNED
Fixed Resistor, Metal Glaze/thick Film, 0.05W, 22100ohm, 30V, 1% +/-Tol, 200ppm/Cel, Surface Mount, 0201, CHIP
VISHAY
©2020 ICPDF网 联系我们和版权申明