CRCW040226K1FKEDC [VISHAY]

RES 26.1K OHM 1% 1/16W 0402;


型号：	CRCW040226K1FKEDC
厂家：	VISHAY
描述：	RES 26.1K OHM 1% 1/16W 0402
文件：	总5页 (文件大小：93K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

CRCW...C e3

www.vishay.com

Vishay

Lead (Pb)-free Thick Film, Rectangular

Commodity Chip Resistors

FEATURES

• High volume product suitable for commercial

applications

• Stability (R/R  1 % for 1000 h at

70 °C)

• Lead (Pb)-free solder contacts on Ni barrier

layer

• Metal glaze on ceramic

• Material categorization: for definitions of compliance

please see www.vishay.com/doc?99912

STANDARD ELECTRICAL SPECIFICATIONS

LIMITING

ELEMENT

VOLTAGE

MAX. V 

CASE

SIZE

CASE

SIZE

POWER RATING

TEMPERATURE

COEFFICIENT

ppm/K

RESISTANCE

RANGE



TOLERANCE

MODEL

P_{70 °C}

E-SERIES

INCH METRIC

100

200

1R0 to 10M

E24; E96

E24

0.063

CRCW0402...C

CRCW0603...C

CRCW0805...C

CRCW1206...C

0402 RR 1005M

Zero-Ohm-Resistor: R_max.= 20 m, I_max.at 70 °C = 1.5 A

100

1R0 to 10M

E24; E96

E24

0.10

0603 RR 1608M

0805 RR 2012M

1206 RR 3216M

200

Zero-Ohm-Resistor: R_max.= 20 m, I_max.at 70 °C = 2.0 A

100

1R0 to 10M

E24; E96

E24

0.125

150

200

Zero-Ohm-Resistor: R_max.= 20 m, I_max.at 70 °C = 2.5 A

100

1R0 to 10M

E24; E96

E24

0.25

200

Zero-Ohm-Resistor: R_max.= 20 m, I_max.at 70 °C = 3.5 A

Notes

•

These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over

operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime

Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material

•

TECHNICAL SPECIFICATIONS

PARAMETER

UNIT

CRCW0402...C

CRCW0603...C

CRCW0805...C

CRCW1206...C

Rated dissipation at 70°C ⁽¹⁾

0.063

0.10

0.125

0.25

Limiting element voltage

150

200

_max.AC/DC

Insulation voltage U_ins.(1 min)

Insulation resistance

Category temperature range

Failure rate



> 75

> 100

> 200

> 300

> 10⁹

°C

h^-1

- 55 to + 155

0.1 x 10^-9

Weight/1000 pieces

0.65

5.5

Note

(1)

The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the

printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded

Revision: 02-Nov-17

Document Number: 28773

For technical questions, contact: ff3aresistors@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

CRCW...C e3

www.vishay.com

Vishay

PART NUMBER AND PRODUCT DESCRIPTION

PART NUMBER: CRCW0603562RFKECC

MODEL/SIZE

VALUE

TOLERANCE

TCR

PACKAGING

SPECIAL

CRCW0402

CRCW0603

CRCW0805

CRCW1206

R = decimal

K = thousand

M = million

F = 1.0 %

J = 5.0 %

Z = jumper

K = 100 ppm/K

N = 200 ppm/K

0 = jumper

EA, EB,

EC, ED,

Up to 2 digits

C = commodity

0000 = jumper

PRODUCT DESCRIPTION: CRCW0603-C 100 562R 1 % ET6 E3

CRCW0603-C

100

562R

1 %

ET6

RESISTANCE

VALUE

MODEL

TCR

TOLERANCE

PACKAGING

LEAD (Pb)-FREE

CRCW0402-C

CRCW0603-C

CRCW0805-C

CRCW1206-C

200 ppm/K

100 ppm/K

10R = 10 

562R = 562 

10K = 10.0 k

1M = 1 M

5 %

1 %

ET1, ET5,

ET6, ET7,

EF4

e3 = pure tin

termination

finish

0R0 = jumper

PACKAGING

DIMENSIONS

TYPE / SIZE

CODE

QUANTITY

PACKAGING STYLE

WIDTH

PITCH

ED = ET7

EE = EF4

EA = ET1

EB = ET5

EC = ET6

EA = ET1

EB = ET5

EC = ET6

EA = ET1

EB = ET5

EC = ET6

10 000

50 000

5000

Ø 180 mm/7"

Ø 330 mm/13"

Ø 180 mm/7"

Ø 254 mm/10"

Ø 330 mm/13"

Ø 180 mm/7"

Ø 254 mm/10"

Ø 330 mm/13"

Ø 180 mm/7"

Ø 254 mm/10"

Ø 330 mm/13"

CRCW0402…C

CRCW0603…C

2 mm

4 mm

10 000

20 000

5000

Paper tape acc. to

IEC 60286-3, Type 1a

8 mm

CRCW0805…C

10 000

20 000

5000

4 mm

CRCW1206…C

10 000

20 000

DIMENSIONS

SOLDER PAD DIMENSIONS ⁽¹⁾(in millimeters)

REFLOW SOLDERING WAVE SOLDERING

SIZE

DIMENSIONS (in millimeters)

0.5 0.05 0.30 0.05 0.25 0.10

1.60 0.10 0.80 0.10 0.45 0.10 0.3 0.2

INCH METRIC

0402

0603

0805

1005

1608

2012

1.0 0.10

0.2 0.1

0.3 0.2

0.35 0.2

0.4

0.5

0.7

0.6

0.9

1.3

0.5

1.0

1.2

0.9

1.3

1.0

1.3

2.0 0.10

1.25 0.15 0.50 0.10 0.35 0.15

+ 0.10

- 0.05

1206

3216

3.05 0.10 1.55 0.10 0.55

0.35 0.15

0.45 0.2

0.9

1.7

2.0

1.1

1.7

2.3

Note

(1)

The rated dissipation applies only if the permitted film temperature is not exceeded. Furthermore, a high level of ambient temperature or of

power dissipation may raise the temperature of the solder joint, hence special solder alloys or board materials maybe required to maintain

the reliability of the assembly. Specified power rating above 125 °C requires dedicated heat-sink pads, which depend on board materials.

The given solder pad dimensions reflect the considerations for board design and assembly as outlined e.g. in standards IEC 61188-5-x, or

in publication IPC-7351. They do not guarantee any supposed thermal properties, particularly as these are also strongly influenced by many

other parameters. Still the given solder pad dimensions will be found adequate for most general applications

Revision: 02-Nov-17

Document Number: 28773

For technical questions, contact: ff3aresistors@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

CRCW...C e3

www.vishay.com

Vishay

FUNCTIONAL PERFORMANCE

120

100

- 55

- 25

100

125

155175

70 Ambient Temperature in °C

Derating

TEST PROCEDURES AND REQUIREMENTS

REQUIREMENTS PERMISSIBLE

CHANGE (R)

IEC 60068-2

EN 60115-1

CLAUSE

TEST

PROCEDURE

STABILITY

CLASS 2

METHOD

CLASS 1

OR BETTER

Stability for product types:

CRCW...C e3

1  to 10 M

4.5

Resistance

1 %

5 %

Temperature

coefficient

(20/- 55/20) °C and

(20/125/20) °C

4.8.4.2

100 ppm/K

200 ppm/K

Short time

overload

4.13

U = 2.5 x P₇₀x R  2 x U_max.;5 s

(2 % R + 0.1 )

Solder bath method;

Sn60Pb40

non activated flux;

(235 5) °C

Good tinning ( 95 % covered)

no visible damage

Pre-aging

4 h at 155 °C,

dryheat

(2 0.2) s

4.17.5

58 (Td)

Solderability

Solder bath method;

Sn96.5Ag3Cu0.5

non activated flux;

(245 5) °C

Good tinning ( 95 % covered)

no visible damage

(3 0.3) s

Resistance to

soldering heat

Solder bath method

(260 5) °C; (10 1) s

4.18.2

4.19

58 (Td)

14 (Na)

(1% R + 0.05 )

30 min. at - 55 °C;

30 min. at 125 °C;

5 cycles

Rapid change

of temperature

(0.25 % R + 0.05 )

(0.5 % R + 0.05 )

(40 2) °C;

56 days;

(93 3) % RH

Damp heat,

steady state

4.24

4.36

78 (Cab)

(1 % R + 0.05 )

(2 % R + 0.1 )

Operation at low

temperature

-55 °C, 1 h

(1 % R + 0.05 )

U = P₇₀x R  U_max.;

1.5 h on; 0.5 h off;

Endurance

at 70 °C

4.25.1

4.25.3

70 °C; 1000 h

70 °C; 8000 h

(1 % R + 0.05 )

(2 % R + 0.1 )

(4 % R + 0.1 )

Endurance at

upper category

temperature

155 °C, 1000 h

(1 % R + 0.05 )

(2 % R + 0.1 )

Revision: 02-Nov-17

Document Number: 28773

For technical questions, contact: ff3aresistors@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

CRCW...C e3

www.vishay.com

Vishay

APPLICABLE SPECIFICATIONS

• EN 60115-1

• EN 140400

Generic specification

Sectional specification

• EN 140401-802

• IEC 60068-2-X

• IEC 60286-3

Detail specification

Variety of environmental test procedures

Packaging of SMD components

Revision: 02-Nov-17

Document Number: 28773

For technical questions, contact: ff3aresistors@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Legal Disclaimer Notice

www.vishay.com

Vishay

Disclaimer

ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE

RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.

Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,

“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other

disclosure relating to any product.

Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or

the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all

liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,

consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular

purpose, non-infringement and merchantability.

Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical

requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements

about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product

with the properties described in the product specification is suitable for use in a particular application. Parameters provided in

datasheets and / or specifications may vary in different applications and performance may vary over time. All operating

parameters, including typical parameters, must be validated for each customer application by the customer's technical experts.

Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited

to the warranty expressed therein.

Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and

for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of

any of the products, services or opinions of the corporation, organization or individual associated with the third-party website.

Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website

or for that of subsequent links.

Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining

applications or for any other application in which the failure of the Vishay product could result in personal injury or death.

Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please

contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by

any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.

Revision: 09-Jul-2021

Document Number: 91000

CRCW040226K1FKEDC [VISHAY]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E