CRCW1218KFNTA [VISHAY]
Lead (Pb)-Bearing Thick Film, Rectangular Chip Resistors; 铅（Pb ） -Bearing厚膜矩形贴片电阻
| 型号： | CRCW1218KFNTA |
| 厂家： | 
VISHAY |
| 描述： | Lead (Pb)-Bearing Thick Film, Rectangular Chip Resistors |
| 文件： | 总8页 (文件大小：130K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
D/CRCW
Vishay
Lead (Pb)-Bearing Thick Film, Rectangular Chip Resistors
FEATURES
• Stability ΔR/R = 1 % for 1000 h at 70 °C
• Lead (Pb)-bearing termination plating on Ni barrier layer
• Metal glaze on high quality ceramic
• Halogen-free according to IEC 61249-2-21 definiton
• AEC-Q200 qualified, rev. C compliant
STANDARD ELECTRICAL SPECIFICATIONS
SIZE
LIMITING
ELEMENT
VOLTAGE
RATED DISSIPATION
TEMPERATURE
COEFFICIENT
ppm/K
RESISTANCE
RANGE
Ω
TOLERANCE
%
P70
W
MODEL
SERIES
INCH METRIC
Umax. AC/DC
100
200
1
5
E24; E96
E24
0.063
50
1R0 to 10M
1R0 to 10M
1R0 to 10M
1R0 to 10M
1R0 to 10M
1R0 to 2M2
1R0 to 10M
1R0 to 10M
D10/CRCW0402 0402 RR 1005M
D11/CRCW0603 0603 RR 1608M
D12/CRCW0805 0805 RR 2012M
D25/CRCW1206 1206 RR 3216M
Zero-Ohm-Resistor: Rmax. = 20 mΩ, Imax. = 1.5 A
100
200
1
5
E24; E96
E24
0.10
75
Zero-Ohm-Resistor: Rmax. = 20 mΩ, Imax. = 2.0 A
100
200
1
5
E24; E96
E24
0.125
150
Zero-Ohm-Resistor: Rmax. = 20 mΩ, Imax. = 2.5 A
100
200
1
5
E24; E96
E24
0.25
200
Zero-Ohm-Resistor: Rmax. = 20 mΩ, Imax. = 3.5 A
100
200
1
5
E24; E96
E24
0.50
200
CRCW1210
CRCW1218
CRCW2010
CRCW2512
1210 RR 3225M
1218 RR 3246M
2010 RR 5025M
2512 RR 6332M
Zero-Ohm-Resistor: Rmax. = 20 mΩ, Imax. = 5.0 A
100
200
1
5
E24; E96
E24
1.0
200
Zero-Ohm-Resistor: Rmax. = 20 mΩ, Imax. = 7.0 A
100
200
1
5
E24; E96
E24
0.75
400
Zero-Ohm-Resistor: Rmax. = 20 mΩ, Imax. = 6.0 A
100
1
5
E24; E96
E24
1.0
500
200
Zero-Ohm-Resistor: Rmax. = 20 mΩ, Imax. = 7.0 A
Notes
• These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift increasing over
operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a functional lifetime.
• Marking: See datasheet “Surface Mount Resistor Marking” (document number 20020).
• Power rating depends on the max. temperature at the solder point, the component placement density and the substrate material.
www.vishay.com
118
For technical questions, contact: thickfilmchip@vishay.com
Document Number: 20008
Revision: 18-Nov-10
D/CRCW
Lead (Pb)-Bearing Thick Film, Rectangular Chip Resistors
Vishay
TECHNICAL SPECIFICATIONS
D10/
D11/
D12/
D25/
PARAMETER
UNIT
CRCW1210 CRCW1218 CRCW2010 CRCW2512
CRCW0402 CRCW0603 CRCW0805 CRCW1206
Rated dissipation at 70 °C (1)
W
0.063
50
0.1
75
0.125
150
0.25
200
0.5
1.0
0.75
400
1.0
Limiting element voltage
UMAX. AC/DC
V
200
200
500
Insulation voltage UINS.
(1 min)
V
> 75
> 100
> 200
> 300
> 300
> 300
> 300
> 300
> 109
Insulation resistance
Ω
Category temperature range °C
- 55 to + 155
< 0.1 x 10-9
Failure rate
Weight
h-1
mg
0.65
2
5.5
10
16
29.5
25.5
40.5
Note
(1) The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support of the
printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature of 155 °C is not exceeded.
PART NUMBER AND PRODUCT DESCRIPTION
Part Number: CRCW0805562RFKTA (2)
C
R
C
W
0
8
0
5
5
6
2
R
F
K
T
A
MODEL
VALUE
TOLERANCE
TCR
PACKAGING
SPECIAL
CRCW0402
CRCW0603
CRCW0805
CRCW1206
CRCW1210
CRCW1218
CRCW2010
CRCW2512
R = Decimal
K = Thousand
M = Million
F = 1 %
J = 5 %
Z = Jumper
K = 100 ppm/K
N = 200 ppm/K
S = Jumper or
special
TA
TB
TC
TD
TE
TF
TG
TH
TK
Up to 2 digits
0000 = Jumper
Product Description: CRCW0805 100 562R 1 % RT1
CRCW0805
100
562R
1 %
RT1
TCR
PACKAGING
MODEL
RESISTANCE VALUE
TOLERANCE
CRCW0402
CRCW0603
CRCW0805
CRCW1206
CRCW1210
CRCW1218
CRCW2010
CRCW2512
100 ppm/K
200 ppm/K
10R = 10 Ω
562R = 562 Ω
10K = 10.0 kΩ
1M = 1 MΩ
1 %
5 %
RT1
RT5
RT6
RT7
RF4
R02
R67
R82
RT9
0R0 = Jumper
Note
(2) Preferred way for ordering products is by use of the PART NUMBER.
Document Number: 20008
Revision: 18-Nov-10
For technical questions, contact: thickfilmchip@vishay.com
www.vishay.com
119
D/CRCW
Lead (Pb)-Bearing Thick Film, Rectangular Chip Resistors
Vishay
PACKAGING
PAPER TAPE
ACC. IEC 60286-3, TYPE I
BLISTER TAPE
ACC. IEC 60286-3, TYPE II
MODEL
UNIT
QUANTITY PART NUMBER PRODUCT DESC. QUANTITY PART NUMBER PRODUCT DESC.
180 mm/7"
330 mm/13"
180 mm/7"
10 000
50 000
5000
TD
TE
TA
TB
TC
TA
TB
TC
TA
TB
TC
TA
TB
TC
RT7
RF4
RT1
RT5
RT6
RT1
RT5
RT6
RT1
RT5
RT6
RT1
RT5
RT6
D10/CRCW0402
D11/CRCW0603 285 mm/11.25"
330 mm/13"
10 000
20 000
5000
180 mm/7"
D12/CRCW0805 285 mm/11.25"
330 mm/13"
10 000
20 000
5000
180 mm/7"
D25/CRCW1206 285 mm/11.25"
330 mm/13"
10 000
20 000
5000
180 mm/7"
CRCW1210
285 mm/11.25"
330 mm/13"
180 mm/7"
10 000
20 000
CRCW1218
CRCW2010
4000
4000
2000
4000
TK
TF
TG
TH
RT9
R02
R67
R82
180 mm/7"
CRCW2512
180 mm/7"
DIMENSIONS
SOLDER PAD DIMENSIONS in millimeters
REFLOW SOLDERING
SIZE
DIMENSIONS in millimeters
WAVE SOLDERING
a
b
l
a
b
l
INCH METRIC
L
W
H
T1
T2
0402
0603
1005
1608
1.0 0.05
0.5 0.05
0.35 0.05 0.25 0.05 0.2 0.1
0.4
0.5
0.6
0.9
0.5
1.0
+ 0.10
1.55
0.85 0.1
0.45 0.05
0.3 0.2
0.3 0.2
0.3 0.2
0.9
0.9
0.9
1.3
1.0
1.3
- 0.05
+ 0.20
2.0
+ 0.20
0.3
0805
2012
1.25 0.15 0.45 0.05
0.7
1.3
1.2
- 0.10
- 0.10
+ 0.10
3.2
1206
1210
1218
3216
3225
3246
1.6 0.15
2.5 0.2
0.55 0.05 0.45 0.2 0.4 0.2
0.55 0.05 0.45 0.2 0.4 0.2
0.55 0.05 0.45 0.2 0.4 0.2
0.9
0.9
1.7
2.5
4.9
2.0
2.0
1.9
1.1
1.1
1.7
2.5
4.8
2.3
2.2
1.9
- 0.20
3.2 0.2
+ 0.10
3.2
4.6 0.15
2.5 0.15
1.05
1.25
- 0.20
2010
2512
5025
6332
5.0 0.15
0.6 0.1
0.6 0.1
0.6 0.2
0.6 0.2
0.6 0.2
0.6 0.2
1.0
1.0
2.5
3.2
3.9
5.2
1.2
1.2
2.5
3.2
3.9
5.2
6.3 0.2
3.15 0.15
www.vishay.com
120
For technical questions, contact: thickfilmchip@vishay.com
Document Number: 20008
Revision: 18-Nov-10
D/CRCW
Lead (Pb)-Bearing Thick Film, Rectangular Chip Resistors
Vishay
FUNCTIONAL PERFORMANCE
Single Pulse
1000
2512
1218
2010
1210
1206
0805
0603
0402
P
100
10
1
0.1
0.01
10-6
10-5
10-4
10-3
10-2
10-1
1
10
100
Pulse Duration ti (s)
Maximum pulse load, single pulse; applicable if P 0 and n < 1000 and Û ≤ Ûmax.
;
for permissible resistance change equivalent to 8000 h operation
Continuous Pulse
1000
100
10
2512
1218
2010
1210
1206
0805
0603
0402
P
1
0.1
0.01
10-6
10-5
10-4
10-3
10-2
10-1
1
10
100
Pulse Duration ti (s)
Maximum pulse load, continuous pulses; applicable if P ≤ P (ϑamb) and Û ≤ Ûmax.
;
for permissible resistance change equivalent to 8000 h operation
Pulse Voltage
2000
2512
1800
Û
1600
2010
1400
1200
1000
1206/1210/1218
800
600
400
200
0
0805
0603
0402
10- 6
10- 5
10- 4
10- 3
10- 2
10- 1
1
10
Pulse Duration ti (s)
Maximum pulse voltage, single and continuous pulses; applicable if
P ≤ Pmax.; for permissible resistance change equivalent to 8000 h operation
Document Number: 20008
Revision: 18-Nov-10
For technical questions, contact: thickfilmchip@vishay.com
www.vishay.com
121
D/CRCW
Lead (Pb)-Bearing Thick Film, Rectangular Chip Resistors
Vishay
Derating
120
100
80
60
40
20
0
- 55
- 25
0
25
50
75
70
100
125
155 175
Ambient Temperature in °C
Non-Linearity
120
100
80
1206, 2010
0805
60
40
20
0
0603
0402
10
100
1K
10K
100K
1M
10M
Resistance Value R in Ω
Current Noise
100
10
1
0.1
0.01
100
1K
10K
100K
1M
10M
Resistance Value R in Ω
www.vishay.com
122
For technical questions, contact: thickfilmchip@vishay.com
Document Number: 20008
Revision: 18-Nov-10
D/CRCW
Lead (Pb)-Bearing Thick Film, Rectangular Chip Resistors
Vishay
TEST PROCEDURES AND REQUIREMENTS
REQUIREMENTS PERMISSIBLE
CHANGE (ΔR)
PROCEDURE
IEC
EN
STABILITY CLASS 1 STABILITY CLASS 2
60082-2
OR BETTER
1 Ω to 10 MΩ
1 %
OR BETTER
1 Ω to 10 MΩ
5 %
60115-1
CLAUSE
TEST
TEST
METHOD
Stability for product types:
D/CRCW
4.5
4.7
-
-
Resistance
-
Voltage proof
U = 1.4 · Uins; 60 s
No flashover or breakdown
U = 2.5 x P70 x R ≤ 2 x Umax.
;
4.13
-
Short time overload
(0.25 % R + 0.05 Ω)
(0.5 % R + 0.05 Ω)
duration: Acc. to style
Solder bath method; Sn60Pb40;
non-activated flux;
Good tinning (≥ 95 %
covered);
4.17.2
58 (Td)
Solderability
(235 5) °C, (2 0.2) s
no visible damage
(20/- 55/20) °C and
(20/125/20) °C
4.8.4.2
4.32
-
Temperature coefficient
Shear (adhesion)
100 ppm/K
200 ppm/K
RR 1608 and smaller: 9 N
RR 2012 and larger: 45 N
21 (Uu3)
No visible damage
No visible damage,
no open circuit in bent position
(0.25 % R + 0.05 Ω)
4.33
4.19
21 (Uu1)
14 (Na)
Substrate bending
Depth 2 mm; 3 times
30 min. at - 55 °C;
30 min. at 125°C
Rapid change of temperature
5 cycles
1000 cycles
(0.25 % R + 0.05 Ω)
(1 % R + 0.05 Ω)
(0.5 % R + 0.05 Ω)
(1 % R + 0.05 Ω)
4.23
-
Climatic sequence:
Dry heat
-
4.23.2
2 (Ba)
125 °C; 16 h
55 °C; ≥ 90 % RH;
4.23.3
30 (Db)
Damp heat, cyclic
24 h; 1 cycle
4.23.4
4.23.5
1 (Aa)
13 (M)
Cold
- 55 °C; 2 h
(1 % R + 0.05 Ω)
(2 % R + 0.1 Ω)
Low air pressure
1 kPa; (25 10) °C; 1 h
55 °C; ≥ 90 % RH;
24 h; 5 cycles
4.23.6
4.23.7
30 (Db)
-
Damp heat, cyclic
DC load
U = P70 x R
U = √(P70 x R) ≤ Umax.
1.5 h on; 0.5 h off;
70 °C; 1000 h
4.25.1
-
Endurance at 70 °C
(1 % R + 0.05 Ω)
(2 % R + 0.1 Ω)
(2 % R + 0.1 Ω)
(4 % R + 0.1 Ω)
70 °C; 8000 h
Solder bath method
(260 5) °C; (10 1) s
4.18.2
4.35
58 (Td)
Resistance to soldering heat
Flamability, needle flame test
Damp heat, steady state
(0.25 % R + 0.05 Ω)
(0.5 % R + 0.05 Ω)
IEC 60695-11-5;
10 s
-
No burning after 30 s
(1 % R + 0.05 Ω)
(1 % R + 0.05 Ω) (2 % R + 0.1 Ω)
(40 2) °C;
(93 3) % RH; 56 days
4.24
78 (Cab)
-
Endurance at upper
category temperature
4.25.3
155 °C; 1000 h
IEC 61340-3-1;
3 pos. + 3 neg. discharges;
ESD test voltage acc. to size
Electrostatic discharge
(human body model)
4.40
-
(1 % R + 0.05 Ω)
Isopropyl alcohol;
50 °C; method 2
4.29
4.30
45 (XA) Component solvent resistance
45 (XA) Solvent resistance of marking
No visible damage
Isopropyl alcohol;
50 °C; method 1, toothbrush
Marking legible,
no visible damage
Document Number: 20008
Revision: 18-Nov-10
For technical questions, contact: thickfilmchip@vishay.com
www.vishay.com
123
D/CRCW
Lead (Pb)-Bearing Thick Film, Rectangular Chip Resistors
Vishay
TEST PROCEDURES AND REQUIREMENTS
REQUIREMENTS PERMISSIBLE
CHANGE (ΔR)
PROCEDURE
IEC
EN
STABILITY CLASS 1 STABILITY CLASS 2
60082-2
OR BETTER
OR BETTER
60115-1
CLAUSE
TEST
TEST
Stability for product types:
METHOD
1 Ω to 10 MΩ
1 Ω to 10 MΩ
D/CRCW
f = 10 Hz to 2000 Hz;
x, y, z ≤ 1.5 mm;
A ≤ 200 m/s2;
Vibration, endurance by
sweeping
4.22
6 (Fc)
(0.25 % R + 0.05 Ω)
(0.5 % R + 0.05 Ω)
10 sweeps per axis
U = 15 x P70 x R ≤ 2 x Umax.
0.1 s on; 2.5 s off;
;
;
4.37
4.27
-
-
Periodic electric overload
(1 % R + 0.05 Ω)
1000 cycles
Single pulse high voltage
overload, 10 µs/700 µs
Û = 10 x P70 x R ≤ 2 x Umax.
(1 % R + 0,05 Ω)
10 pulses
All tests are carried out in accordance with the following specifications:
• EN 60115-1, generic specification
• EN 140400, sectional specification
• EN 140401-802, detail specification
• IEC 60068-2, environmental test procedures
Packaging of components is done in paper or blister tapes according to IEC 60286-3.
www.vishay.com
124
For technical questions, contact: thickfilmchip@vishay.com
Document Number: 20008
Revision: 18-Nov-10
Legal Disclaimer Notice
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Document Number: 91000
Revision: 11-Mar-11
www.vishay.com
1
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明