LH1521BACTR_11 [VISHAY]
Dual 1 Form B Solid-State Relay; 双1表格B固态继电器型号: | LH1521BACTR_11 |
厂家: | VISHAY |
描述: | Dual 1 Form B Solid-State Relay |
文件: | 总4页 (文件大小:107K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LH1521BACTR
Vishay Semiconductors
www.vishay.com
Dual 1 Form B Solid-State Relay
FEATURES
• Dual channel (LH1501)
• Isolation test voltage 3750 VRMS
• Typical RON 20
S1
S1'
S2
S2'
• Load voltage 350 V
SMD
• Load current 150 mA
• High surge capability
S1
S1' S2
S2'
5
• Clean bounce free switching
• Low power consumption
• SMD lead available on tape and reel
8
7
6
i179034_11
• Compliant to RoHS Directive 2002/95/EC and in
accordance to WEEE 2002/96/EC
1
2
3
4
APPLICATIONS
• General telecom switching
- On/off hook control
- Ring delay
DESCRIPTION
The LH1521 dual 1 form B relays are SPST normally closed
switches that can replace electromechanical relays in many
applications. The relays are constructed as a multi chip
hybrid device. Actuation control is via an infrared LED. The
output switch is a combination of a photodiode array with
MOSFET switches and control circuity.
- Dial pulse
- Ground start
- Ground fault protection
• Instrumentation
• Industrial controls
AGENCY APPROVALS
UL1577: file no. E52744 system code H, double protection
CSA:
certification no. 093751
DIN EN: 60747-5-2 (VDE 0884)/60747-5-5 (pending),
available with option 1
FIMKO: 25419
ORDERING INFORMATION
SMD-8
L
H
1
5
2
1
B
#
#
T
R
PART NUMBER
ELECTR.
VARIATION
PACKAGE
CONFIG.
TAPE AND
REEL
> 0.1 mm
PACKAGE
UL, CSA, FIMKO
LH1521BACTR
SMD-8, tape and reel
Rev. 1.6, 03-Aug-11
Document Number: 83820
1
For technical questions, contact: optocoupleranswers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
LH1521BACTR
Vishay Semiconductors
www.vishay.com
ABSOLUTE MAXIMUM RATINGS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
SYMBOL
VALUE
UNIT
INPUT
LED continuous forward current
LED reverse voltage
IF
50
5
mA
V
IR 10 μA
IL 50 μA
VR
OUTPUT
DC or peak AC load voltage
Continuous DC load current one pole operating
VL
IL
350
150
V
mA
Continuous DC load current two poles
operating
IL
IP
110
400
mA
mA
Peak load current (single shot)
SSR
t = 100 ms
Output power dissipation (continuous)
Ambient temperature range
Storage temperature range
Pin soldering temperature (2)
Input to output isolation voltage
Pdiss
Tamb
Tstg
600
- 40 to + 85
- 40 to + 125
260
mW
°C
°C
t = 10 s max.
Tsld
°C
t = 1 s, IISO = 10 μA max.
VISO
3750
VRMS
Pole-to-pole isolation voltage (S1 to S2) (1)
(dry air, dust free, at sea level)
1600
V
Notes
•
Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. Functional operation of the device is not
implied at these or any other conditions in excess of those given in the operational sections of this document. Exposure to absolute
maximum ratings for extended periods of the time can adversely affect reliability.
Breakdown occurs between the output pins external to the package.
Refer to reflow profile for soldering conditions for surface mounted devices (SMD). Refer to wave profile for soldering conditions for through
hole devices (DIP).
(1)
(2)
ELECTRICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
SYMBOL
MIN.
TYP.
MAX.
UNIT
INPUT
LED forward current switch turn-on
LED forward current switch turn-off
LED forward voltage
OUTPUT
IL = 150 mA, t = 10 ms
VL = 300 V
IFon
IFoff
VF
0.2
0.9
1
mA
mA
V
2
IF = 10 mA
1.15
1.22
1.45
On-resistance
IF = 0 mA, IL = 50 mA
IF = 5 mA, VL = 100 V
IF = 5 mA, VL = 350 V
IF = 5 mA, VL = 50 V
RON
20
1.4
0.08
50
25
1
Off-resistance
ROFF
0.1
G
μA
pF
Off-state leakage current
Output capacitance
TRANSFER
Capacitance (input to output)
VISO = 1 V
CIO
3
pF
Note
•
Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering
evaluations. Typical values are for information only and are not part of the testing requirements.
SWITCHING CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
Turn-on time
Turn-off time
TEST CONDITION
IF = 5 mA, IL = 50 mA
IF = 5 mA, IL = 50 mA
SYMBOL
MIN.
TYP.
MAX.
UNIT
ms
ton
toff
2
1
3
3
ms
Rev. 1.6, 03-Aug-11
Document Number: 83820
2
For technical questions, contact: optocoupleranswers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
LH1521BACTR
Vishay Semiconductors
www.vishay.com
TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
150
120
90
50
30
0
- 40 - 20
0
20
40
60
80
Ambient Temperature (°C)
ilh1521bb_00
Fig. 1 - Recommended Operating Conditions
PACKAGE DIMENSIONS in millimeters
SMD
9.65
2.54
2.54
8.31
6.35
9.53
1.9
0.46
8.08
1.5
7.62
3.3
4.45
ISO method A
0.25 typ.
i178018
0.64 typ.
PACKAGE MARKING (example)
LH1521
V YWW H 68
Note
•
Tape and reel suffix (TR) is not part of the package marking.
Rev. 1.6, 03-Aug-11
Document Number: 83820
3
For technical questions, contact: optocoupleranswers@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Document Number: 91000
Revision: 11-Mar-11
www.vishay.com
1
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明