MCT0603MD1320DP500 [VISHAY]
RESISTOR, THIN FILM, 0.1 W, 0.5 %, 25 ppm, 132 ohm, SURFACE MOUNT, 0603, CHIP, GREEN PRODUCT;
| 型号： | MCT0603MD1320DP500 |
| 厂家： | 
VISHAY |
| 描述： | RESISTOR, THIN FILM, 0.1 W, 0.5 %, 25 ppm, 132 ohm, SURFACE MOUNT, 0603, CHIP, GREEN PRODUCT 电阻器 |
| 文件： | 总10页 (文件大小：144K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MCT 0603 AT - Professional
Vishay Beyschlag
Professional Automotive Thin Film Chip Resistor
FEATURES
• Operating temperature 175 °C, 1000 h
• Superior moisture resistivity < 0.5 % (85 °C;
85 % RH; 1000 h)
RoHS
COMPLIANT
• Rated dissipation P85 = 150 mW
• AEC-Q200 compliant
• Green product, supports lead (Pb)-free soldering, RoHS
compliant
APPLICATIONS
• Automotive
• Telecommunication
• Medical equipment
• Industrial equipment
MCT 0603 AT Professional Thin Film Chip Resistors are the
perfect choice for most fields of modern professional
electronics where reliability and stability is of major concern.
Typical applications include automotive, telecommunication,
industrial, medical equipment, precision test and measuring
equipment.
METRIC SIZE
INCH:
0603
METRIC:
RR1608M
TECHNICAL SPECIFICATIONS
DESCRIPTION
MCT 0603 AT
RR1608M
Metric size
Resistance range
Resistance tolerance
Temperature coefficient
100 Ω to 100 kΩ
1 %; 0.5 %
50 ppm/K; 25 ppm/K
0.150 W
(1)
Rated dissipation P85
Operating voltage, Umax. AC/DC
Permissible film temperature (1)
Thermal resistance (2)
Insulation voltage
75 V
175 °C
≤ 550 K/W
1 min; Uins
100 V
75 V
continuous
Observed failure rate FITobserved
≤ 0.1 x 10- 9/h
Notes
(1)
Please refer to APPLICATION INFORMATION below
Measuring conditions in accordance with EN 140401-801
(2)
www.vishay.com
1
For technical questions, contact: filmresistors.thinfilmchip@vishay.com
Document Number: 28760
Revision: 07-May-08
MCT 0603 AT - Professional
Professional Automotive Thin Film Chip Resistor
Vishay Beyschlag
APPLICATION INFORMATION
The power dissipation on the resistor generates a temperature rise against the local ambient, depending on the heat flow support
of the printed-circuit board (thermal resistance). The rated dissipation applies only if the permitted film temperature is not
exceeded.
These resistors do not feature a limited lifetime when operated within the permissible limits. However, resistance value drift
increasing over operating time may result in exceeding a limit acceptable to the specific application, thereby establishing a
functional lifetime. At the maximum permissible film temperature of 175 °C the useful lifetime is specified for 1000 h. The
designer may estimate the performance of the particular resistor application or set certain load and temperature limits in order to
maintain a desired stability.
MAXIMUM RESISTANCE CHANGE AT RATED POWER
DESCRIPTION
MCT 0603 AT
RR1608M
Power
Metric size
Operation mode
Standard
P70 = 0.1 W
125 °C
Advanced Temperature
P85 = 0.15 W
Rated power
P70 = 0.125 W
155 °C
Film temperature
175 °C
Max. resistance change at P70 for resistance range:
100 Ω to 100 kΩ
ΔR/R max., after:
1000 h
8000 h
≤ 0.15 %
≤ 0.25 %
≤ 1.0 %
≤ 0.25 %
≤ 0.5 %
-
225 000 h
Max. resistance change at P85 for resistance range:
ΔR/R max., after:
100 Ω to 100 kΩ
≤ 0.5 %
1000 h
PART NUMBER AND PRODUCT DESCRIPTION (1)
PART NUMBER: MCT0603MD4641DPW00
M
C
T
0
6
0
3
M
D
4
6
4
1
D
P
W
0
0
SPECIAL
CHARACTER
MODEL/SIZE
TCR
VALUE
TOLERANCE
PACKAGING (2)
SPECIAL
MCT0603
M = AT
(Automotive)
D
C
=
=
Z
25 ppm/K
50 ppm/K
= Jumper
3 digit value
1 digit
D = 0.5 %
F = 1 %
Z = Jumper
P5
PW
up to 2 digits
00 = standard
multiplier
MULTIPLIER
0 = *100
1 = *101
2 = *102
3 = *103
4 = *104
0000 = Jumper
PRODUCT DESCRIPTION: MCT 0603 - 25 0.5 % AT PW 4K64
0603
- 25
0.5 %
AT
MCT
PW
4K64
TOLERANCE
VALUE
SPECIAL
CHARACTER
RESISTANCE
VALUE
MODEL
SIZE
TCR
PACKAGING (2)
MCT
0603
25 ppm/K
50 ppm/K
0.5 %
1 %
AT = Automotive
P5
PW
47K = 47 kΩ
0R0 = Jumper
Notes
(1)
Products can be ordered using either the PART NUMBER and PRODUCT DESCRIPTION
Please refer to table PACKAGING below
(2)
Document Number: 28760
Revision: 07-May-08
For technical questions, contact: filmresistors.thinfilmchip@vishay.com
www.vishay.com
2
MCT 0603 AT - Professional
Professional Automotive Thin Film Chip Resistor
Vishay Beyschlag
DIMENSIONS
T1
WT
W
H
T2
L
DIMENSIONS - chip resistor types, mass and relevant physical dimensions
H
(mm)
L
W
(mm)
WT
(mm)
T1
(mm)
T2
(mm)
MASS
(mg)
TYPE
(mm)
MCT 0603 AT 0.45 + 0.1/- 0.05
1.55 0.05
0.85 0.1
> 75 % of W
0.3 + 0.15/- 0.2
0.3 + 0.15/- 0.2
1.9
TEMPERATURE COEFFICIENT AND RESISTANCE RANGE
DESCRIPTION
RESISTANCE VALUE (1)
TCR
TOLERANCE
MCT 0603 AT
1 %
0.5 %
0.5 %
-
100 Ω to 100 kΩ
100 Ω to 100 kΩ
100 Ω to 100 kΩ
≤ 20 mΩ; Imax. = 1 A
50 ppm/K
25 ppm/K
Jumper
Note
(1)
Resistance values to be selected for 1 % tolerance from E24 and E96; for 0.5 % tolerance from E24 and E192
Resistance ranges printed in bold are preferred TCR/tolerance combinations with optimized availability.
PACKAGING
REEL
MODEL
PIECES/
CODE
PAPER TAPE ON REEL
5000
P5
MCT 0603 AT
20 000
PW
www.vishay.com
3
For technical questions, contact: filmresistors.thinfilmchip@vishay.com
Document Number: 28760
Revision: 07-May-08
MCT 0603 AT - Professional
Professional Automotive Thin Film Chip Resistor
Vishay Beyschlag
plating against tin whisker growth has been proven under
extensive testing.
DESCRIPTION
Production is strictly controlled and follows an extensive set
of instructions established for reproducibility.
(1)
A
All products comply with the GADSL
CEFIC-EECA-EICTA
and the
(2)
homogeneous film of metal alloy is deposited on a high grade
(96 % Al2O3) ceramic substrate and conditioned to achieve
the desired temperature coefficient. Specially designed inner
contacts are deposited on both sides. A special laser is used
to achieve the target value by smoothly cutting a meander
groove in the resistive layer without damaging the ceramics.
The resistor elements are covered by a protective coating
designed for electrical, mechanical and climatic protection.
The terminations receive a final pure tin on nickel plating.
list of legal restrictions on
hazardous substances. This includes full compliance with
the following directives:
• 2000/53/EC End of Vehicle life Directive (ELV) and
Annex II (ELV II)
• 2002/95/EC Restriction of the use of Hazardous
Substances directive (RoHS)
• 2002/96/EC Waste Electrical and Electronic Equipment
Directive (WEEE)
The result of the determined production is verified by an
extensive testing procedure and optical inspection
performed on 100 % of the individual chip resistors. Only
accepted products are laid directly into the paper tape in
accordance with EN 60286-3.
APPROVALS
The resistors are tested in accordance with EN 140401-801
(superseding CECC 40401-801) which refers to EN 60115-1
and EN 140400. The approval is valid with regards to rated
power P70 and a temperature range of - 55 °C to 155 °C.
ASSEMBLY
The resistors are suitable for processing on automatic SMD
assembly systems. They are suitable for automatic soldering
using wave, reflow or vapour phase as shown in
IEC 61760-1*. The encapsulation is resistant to all cleaning
solvents commonly used in the electronics industry,
including alcohols, esters and aqueous solutions. The
suitability of conformal coatings, if applied, shall be qualified
by appropriate means to ensure the long-term stability of the
whole system. The resistors are RoHS compliant; the pure
tin plating provides compatibility with lead (Pb)-free and
lead-containing soldering processes. Solderability is
specified for 2 years after production or requalification. The
permitted storage time is 20 years. The immunity of the
Approval of conformity is indicated by the CECC logo on the
package label.
Vishay BEYSCHLAG has achieved “Approval of
Manufacturer“ in accordance with EN 100114-1. The
release certificate for “Technology Approval Schedule“ in
accordance with CECC 240 001 based on EN 100114-6 is
granted for the Vishay BEYSCHLAG manufacturing process.
SPECIALS
This product family of thin film flat chip resistors is completed
by Zero Ohm Jumpers.
Notes
•
The quoted IEC standards marked with an asterisk (*) are also released as EN standards with the same number and identical contents
(1)
Global Automotive Declarable Substance List, see www.gadsl.org
(2)
CEFIC (European Chemical Industry Council), EECA (European Electronic Component Manufacturers Association), EICTA (European trade
organisation representing the information and communications technology and consumer electronics), see www.eicta.org → issue →
environment policy → chemicals → chemicals for electronics
Document Number: 28760
Revision: 07-May-08
For technical questions, contact: filmresistors.thinfilmchip@vishay.com
www.vishay.com
4
MCT 0603 AT - Professional
Professional Automotive Thin Film Chip Resistor
Vishay Beyschlag
FUNCTIONAL PERFORMANCE
P
Standard
Power
Advanced Temperature
0.2
W
0.1
°C
- 50
0
50
70 85 100
150
175
Ambient Temperature
ϑamb
For permissible resistance change please refer to table MAXIMUM RESISTANCE CHANGE AT RATED POWER
Derating
MCT 0603 AT
P
100
W
10
1
0.1
10 µs
100 µs
1 ms
10 ms
100 ms
1 s
10 s
Pulse Duration ti
Maximum pulse load, single pulse; for permissible resistance change equivalent to 8000 h operation
Single Pulse
MCT 0603 AT
P
100
W
10
1
0.1
10 µs
100 µs
1 ms
10 ms
100 ms
1 s
10 s
Pulse Duration ti
Maximum pulse load, continous pulses; for permissible resistance change equivalent to 8000 h operation
Continuous Pulse
www.vishay.com
5
For technical questions, contact: filmresistors.thinfilmchip@vishay.com
Document Number: 28760
Revision: 07-May-08
MCT 0603 AT - Professional
Professional Automotive Thin Film Chip Resistor
Vishay Beyschlag
1 kV
• 2
MCT 0603 AT
U
100 V
10 V
10 µs
100 µs
1 ms
10 ms
100 ms
1 s
10 s
Pulse Duration ti
Maximum pulse voltage, single and continuous pulses; for permissible resistance change equivalent to 8000 h operation
Pulse Voltage
MCT 0603 AT
10 kV
1 kV
100 V
10 V
10 Ω
100 Ω
1 kΩ
10 kΩ
100 kΩ
1 MΩ
10 MΩ
Resistance Value R
Pulse load rating in accordance with EN 60115-1 clause 4.27; 1.2 µs/50 µs; 5 pulses at 12 s interval;
for permissible resistance change 0.5 %
1.2/50 Pulse
MCT 0603 AT
10 kV
1 kV
100 V
10 V
10 Ω
100 Ω
1 kΩ
10 kΩ
100 kΩ
1 MΩ
10 MΩ
Resistance Value R
Pulse load rating in accordance with EN 60115-1 clause 4.27; 10 µs/700 µs;
10 pulses at 1 minute intervals; for permissible resistance change 0.5 %
10/700 Pulse
Document Number: 28760
Revision: 07-May-08
For technical questions, contact: filmresistors.thinfilmchip@vishay.com
www.vishay.com
6
MCT 0603 AT - Professional
Professional Automotive Thin Film Chip Resistor
Vishay Beyschlag
A
1
µV/V
0.1
MCT 0603 AT
0.01
1 k
Ω
10 kΩ
100 kΩ
1 MΩ
10 MΩ
Resistance Value R
Current noise A1 in accordance with IEC 60 195
Current Noise
2.0
1.5
•)
1.0
MCT 0603 AT
•)
0.5
0.3
0.1
1
GHz
20
3
10
Frequency f
IZI/R for 49.9 Ω chip resistor
RF-Behaviour
TESTS AND REQUIREMENTS
All tests are carried out in accordance with the following
specifications:
Category Temperature; damp heat, long term, 56 days) is
valid (LCT = - 55 °C/UCT = 155 °C).
EN 60115-1, Generic specification
EN 140 400, Sectional specification
EN 140 401-801, Detail specification
Unless otherwise specified the following values apply:
Temperature: 15 °C to 35 °C
Relative humidity: 45 % to 75 %
The components are approved in accordance with the
European CECC-system, where applicable. The following
table contains only the most important tests. For the full test
schedule refer to the documents listed above. The testing
also covers most of the requirements specified by
EIA/IS-703 and JIS-C-5202.
Air pressure: 86 kPa to 106 kPa (860 mbar to 1 060 mbar).
The components are mounted for testing on boards in
accordance with EN 60115-1, 4.31 unless otherwise
specified.
The requirements stated in the Test Procedures and
Requirements table are based on the required tests and
permitted limits of EN 140 401-801. However, some
additional tests and a number of improvements against those
minimum requirements have been included.
The tests are carried out in accordance with IEC 60068 and
under standard atmospheric conditions in accordance with
IEC 60068-1, 5.3. Climatic category LCT/UCT/56 (rated
temperature range: Lower Category Temperature, Upper
www.vishay.com
7
For technical questions, contact: filmresistors.thinfilmchip@vishay.com
Document Number: 28760
Revision: 07-May-08
MCT 0603 AT - Professional
Professional Automotive Thin Film Chip Resistor
Vishay Beyschlag
TEST PROCEDURES AND REQUIREMENTS
IEC
60068-2
TEST
METHOD
REQUIREMENTS
PERMISSIBLE CHANGE (ΔR/R)
EN
60115-1
CLAUSE
TEST
PROCEDURE
STABILITY CLASS 0.5
Stability for product types:
MCT 0603 AT
100 Ω to 100 kΩ
4.5
-
-
Resistance
1 %; 0.5 %
Temperature
coefficient
At 20/- 55/20 °C and
20/155/20 °C
4.8.4.2
50 ppm/K; 25 ppm/K
U = P70 x R or
U = Umax.
whichever is the less severe;
;
Endurance at
70 °C: standard
operation mode
70 °C; 1000 h
(0.15 % R + 0.05 Ω)
(0.25 % R + 0.05 Ω)
70 °C; 8000 h
4.25.1
-
U = P70 x R or
U = Umax.
whichever is the less severe;
;
Endurance at
70 °C: power
operation mode
70 °C; 1000 h
(0.3 % R + 0.05 Ω)
(0.5 % R + 0.05 Ω)
70 °C; 8000 h
Endurance at
upper category
temperature
125 °C; 1000 h
155 °C; 1000 h
175 °C; 1000 h
(0.15 % R + 0.05 Ω)
(0.3 % R + 0.05 Ω)
(0.5 % R + 0.05 Ω)
4.25.3
4.24
-
(40 2) °C; 56 days;
(93 3) % RH
Damp heat,
steady state
78 (Cab)
(0.1 % R + 0.05 Ω)
(0.5 % R + 0.05 Ω)
U = 0.3 Urated
(85 2) °C;
(85 5) % RH
U = 0.3 Urated
1000 h
Damp heat,
steady state,
accelerated
4.39
67 (Cy)
4.23
Climatic sequence:
dry heat
4.23.2
2 (Ba)
155 °C; 16 h
55 °C; 24 h; > 90 % RH;
4.23.3
30 (Db)
damp heat, cyclic
1 cycle
4.23.4
4.23.5
1 (Aa)
13 (M)
cold
- 55 °C; 2 h
(0.5 % R + 0.05 Ω)
low air pressure
8.5 kPa; 2 h; 25 10 °C
55 °C; 5 days > 90 % RH;
4.23.6
4.23.7
-
30 (Db)
-
damp heat, cyclic
d.c. load
5 cycles
U = P70 x R ≤ Umax.; 1 min
- 55 °C; 2 h
Storage at low
temperature
1 (Aa)
(0.1 % R + 0.01 Ω)
(0.5 % R + 0.01 Ω)
30 min at - 55 °C and
30 min at 155 °C;
1000 cycles
Rapid change of
temperature
4.19
14 (Na)
Document Number: 28760
Revision: 07-May-08
For technical questions, contact: filmresistors.thinfilmchip@vishay.com
www.vishay.com
8
MCT 0603 AT - Professional
Professional Automotive Thin Film Chip Resistor
Vishay Beyschlag
TEST PROCEDURES AND REQUIREMENTS
IEC
60068-2
TEST
METHOD
REQUIREMENTS
PERMISSIBLE CHANGE (ΔR/R)
EN
60115-1
CLAUSE
TEST
PROCEDURE
STABILITY CLASS 0.5
Stability for product types:
MCT 0603 AT
100 Ω to 100 kΩ
Short time
overload;
standard
(0.1 % R + 0.01 Ω)
operation mode
U = 2.5 x P70 x R
≤ 2 × Umax.; 5 s
4.13
4.27
4.37
-
-
-
Short time
overload;
power
(0.25 % R + 0.05 Ω)
(0.25 % R + 0.05 Ω)
(0.5 % R + 0.05 Ω)
(0.5 % R + 0.05 Ω)
operation mode
Single pulse high
voltage overload;
standard
Severity no. 4:
U = 10 x P70 x R
operation mode
≤ 2 x Umax.
;
Single pulse high
voltage overload;
power
10 pulses
operation mode
Periodic electric
overload;
standard
operation mode
U = 15 x P70 x R
≤ 2 x Umax.
;
0.1 s ON; 2.5 s OFF;
Periodic electric
overload;
1000 cycles
(1.0 % R + 0.05 Ω)
(0.5 % R + 0.05 Ω)
power
operation mode
ESD (Electro Static
Discharge)
MIL-STD-883, Method 3015;
1000 V
-
-
Endurance by sweeping;
10 to 2000 Hz;
(0.1 % R + 0.01 Ω)
no visible damage
4.22
6 (Fc)
Vibration
no resonance;
amplitude ≤ 1.5 mm or
≤ 200 m/s2; 6 h
Solder bath method;
SnPb40; non-activated flux
(215 3) °C; (3 0.3) s
Good tinning (≥ 95 % covered);
no visible damage
4.17.2
4.18.2
58 (Td)
58 (Td)
Solderability
Solder bath method;
SnAg3Cu0.5 or SnAg3.5;
non-activated flux;
Good tinning (≥ 95 % covered);
no visible damage
(245 3) °C; (3 0.2) s
Resistance to
soldering heat
Solder bath method;
(260 5) °C; (10 1) s
(0.1 % R + 0.01 Ω)
no visible damage
Component solvent
resistance
Isopropyl alcohol + 50 °C;
4.29
4.32
4.33
45 (XA)
21 (Ue3)
21 (Ue1)
No visible damage
No visible damage
method 2
Shear (adhesion)
Substrate bending
RR 1608M; 9 N
(0.1 % R + 0.01 Ω)
no visible damage; no open circuit in bent position
Depth 2 mm, 3 times
4.7
-
-
Voltage proof
Flammability
Urms = Uins; 60 5 s
No flashover or breakdown
No burning after 30 s
4.35
Needle flame test; 10 s
www.vishay.com
9
For technical questions, contact: filmresistors.thinfilmchip@vishay.com
Document Number: 28760
Revision: 07-May-08
Legal Disclaimer Notice
Vishay
Disclaimer
All product specifications and data are subject to change without notice.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf
(collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein
or in any other disclosure relating to any product.
Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any
information provided herein to the maximum extent permitted by law. The product specifications do not expand or
otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed
therein, which apply to these products.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this
document or by any conduct of Vishay.
The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless
otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such
applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting
from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding
products designed for such applications.
Product names and markings noted herein may be trademarks of their respective owners.
Document Number: 91000
Revision: 18-Jul-08
www.vishay.com
1
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明