MKP1839468634HQG [VISHAY]
CAPACITOR, METALLIZED FILM, POLYPROPYLENE, 630 V, 0.68 uF, THROUGH HOLE MOUNT, AXIAL LEADED, ROHS COMPLIANT;型号: | MKP1839468634HQG |
厂家: | VISHAY |
描述: | CAPACITOR, METALLIZED FILM, POLYPROPYLENE, 630 V, 0.68 uF, THROUGH HOLE MOUNT, AXIAL LEADED, ROHS COMPLIANT 电容器 |
文件: | 总12页 (文件大小:131K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MKP 1839 HQ
Vishay Roederstein
AC and Pulse Metallized Polypropylene Film Capacitors
MKP Axial Type
FEATURES
Supplied loose in box, taped on ammopack or reel
available on request
• Compliant to RoHS directive 2002/95/EC
Ødt
d
lt
l
lt
ENCAPSULATION
Plastic-wrapped, epoxy resin sealed. Flame
retardant.
APPLICATIONS
CLIMATIC TESTING CLASS ACC. TO
IEC 60068-1
High current and high pulse operations
55/110/56
REFERENCE STANDARDS
IEC 60384-17
CAPACITANCE RANGE (E12 SERIES)
0.1 µF to 3.3 µF
MARKING
CAPACITANCE TOLERANCE
5 %
Manufacturer’s logo; code for dielectric material;
manufacturer’s type designation; C-code; rated
voltage-code; tolerance-code; special n °C-value; tolerance;
rated voltage; year and week; manufacturer’s location
LEADS
Tinned wire
DIELECTRIC
RATED TEMPERATURE
85 °C
Polypropylene film
MAXIMUM APPLICATION TEMPERATURE
At 85 °C: UC = 1.0 UR
at 110 °C: UC = 0.7 UR
ELECTRODES
Metallized
CONSTRUCTION
PULL TEST ON LEADS
Series construction
≥ 20 N in direction of leads according to IEC 60068-2-21
BENT TEST ON LEADS
2 bends trough 90° with half of the force used in pull test
RATED (DC) VOLTAGE
630 V, 850 V, 1250 V, 1600 V
RELIABILITY
RATED (AC) VOLTAGE
Operation life > 300 000 h
300 V, 400 V, 450 V, 600 V
Failure rate < 5 FIT (40 °C and 0.5 x UR)
DETAIL SPECIFICATION
For more detailed data and test requirements contact:
dc-film@vishay.com
www.vishay.com
258
For technical questions, contact: dc-film@vishay.com
Document Number: 28162
Revision: 21-Apr-10
MKP 1839 HQ
AC and Pulse Metallized Polypropylene Film Capacitors
MKP Axial Type
Vishay Roederstein
COMPOSITION OF CATALOG NUMBER
MULTIPLIER
(nF)
SPECIAL LETTER
FOR TAPED
CAPACITANCE
(numerically)
0.1
2
3
4
5
Bulk
1
R
Reel
Example:
468 = 680 nF
10
G
Ammopack
Special
(1)
100
HIGH QUALITY
CAPACITOR
TYPE
MKP 1839
X
XX
08
X
HQ
X
VOLTAGE (Vdc)
63 = 630 V
TOLERANCE
4
5 %
08 = 850 V
12 = 1250 V
13 = 1600 V
Note
(1)
For detailed tape specifications refer to “Packaging Information”: www.vishay.com/doc?28139 or end of catalog
SPECIFIC REFERENCE DATA
DESCRIPTION
Tangent of loss angle:
VALUE
at 10 kHz
≤ 5 x 10-4
≤ 8 x 10-4
≤ 10 x 10-4
at 1 kHz
≤ 3 x 10-4
≤ 3 x 10-4
≤ 3 x 10-4
at 100 kHz
≤ 35 x 10-4
≤ 50 x 10-4
≤ 60 x 10-4
0.1 µF < C ≤ 0.47 µF
0.47 µF < C ≤ 1 µF
1 µF < C ≤ 3.3 µF
630 VDC
850 VDC
1000 V/µs
1130 V
1250 VDC
1000 V/µs
1400 V
1600 VDC
Rated voltage pulse slope
(dU/dt)R at URdc
500 V/µs
700 V
1000 V/µs
1600 V
U
P-P peak-to-peak voltage
R between leads,
for C ≤ 0.33 µF at 500 V, 1 min
> 100 GΩ
> 30 000 s
> 100 GΩ
RC between leads,
for C > 0.33 µF at 500 V, 1 min
R between interconnecting and
wrapped film at 500 V, 1 min
1008 V
1360 V
2000 V
2560 V
Withstanding (DC) voltage (cut off
current 10 mA), rise time 100 V/s
1 min
2840 V, 1 min
110 °C
Withstanding (DC) voltage between
leads and wrapped film
(1.4 x URac + 2000)
Maximum application temperature
Document Number: 28162
Revision: 21-Apr-10
For technical questions, contact: dc-film@vishay.com
www.vishay.com
259
MKP 1839 HQ
AC and Pulse Metallized Polypropylene Film Capacitors
MKP Axial Type
Vishay Roederstein
VOLTAGE CODE 63
630 VDC/300 VAC
VOLTAGE CODE 08
850 VDC/400 VAC
CAPACITANCE
DIMENSIONS
max.
DIMENSIONS
max.
dt
dt
SPQ (1)
SPQ (1)
MASS
MASS
0.08 mm
0.08 mm
(mm)
(mm)
(µF)
0.1
D
7
L
(g)
0.9
1.2
1.4
1.6
1.9
2.3
2.6
3.0
3.5
4.2
5.1
6.1
9.0
13.1
19.5
(mm)
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1.0
1.0
1.0
Pieces
2000
1750
1500
1250
1000
900
D
8.5
10
L
(g)
1.6
2.3
2.7
3.2
3.9
4.6
5.4
6.5
5.4
6.5
7.8
9.4
13.9
-
(mm)
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1.0
1.0
1.0
-
Pieces
1500
1000
850
26.5
26.5
26.5
26.5
26.5
26.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
-
0.15
0.18
0.22
0.27
0.33
0.39
0.47
0.56
0.68
0.82
1
8
8.5
9.5
10
11
10.5
11
12
13
14
16
19
23
28
11
11.5
13
750
1000
1000
1000
1000
1000
1000
750
14
900
15
750
16.5
15
650
500
16.5
18
1000
900
19.5
24
600
1.5
600
400
2.2
450
-
-
3.3
300
-
-
-
-
-
VOLTAGE CODE 12
1250 VDC/450 VAC
VOLTAGE CODE 13
1600 VDC/600 VAC
CAPACITANCE
DIMENSIONS
max.
DIMENSIONS
max.
dt
dt
SPQ (1)
SPQ (1)
MASS
MASS
0.08 mm
0.08 mm
(mm)
(mm)
(µF)
0.1
D
8.5
10
11
11.5
13
14
15
16.5
18
20
21.5
23.5
-
L
(g)
1.6
2.3
2.7
3.2
3.9
4.6
5.4
6.5
7.7
9.2
11.1
13.4
-
(mm)
0.8
0.8
0.8
0.8
0.8
0.8
0.8
0.8
1.0
1.0
1.0
1.0
-
Pieces
1500
1000
1000
800
650
500
1000
900
750
600
500
400
-
D
10.5
12.5
13.5
15
L
(g)
2.7
3.9
4.6
5.5
6.7
8.1
9.5
11.3
13.4
16.2
-
(mm)
0.8
0.8
0.8
0.8
0.8
1.0
1.0
1.0
1.0
1.0
-
Pieces
1000
600
500
500
900
750
600
500
400
350
-
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
-
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
31.5
-
0.15
0.18
0.22
0.27
0.33
0.39
0.47
0.56
0.68
0.82
1
16.5
18
19.5
21.5
23.5
25.5
-
-
-
-
-
-
1.5
-
-
-
-
-
2.2
-
-
-
-
-
-
-
-
-
-
3.3
-
-
-
-
-
-
-
-
-
-
Note
(1) SPQ = Standard Packing Quantity
www.vishay.com
260
For technical questions, contact: dc-film@vishay.com
Document Number: 28162
Revision: 21-Apr-10
MKP 1839 HQ
AC and Pulse Metallized Polypropylene Film Capacitors
MKP Axial Type
Vishay Roederstein
MOUNTING
Normal Use
The capacitors are designed for mounting on printed-circuit boards. The capacitors packed in bandoliers are designed for
mounting in printed-circuit boards by means of automatic insertion machines.
Specific Method of Mounting to Withstand Vibration and Shock
In order to withstand vibration and shock tests, it must be ensured that the capacitor body is in good contact with the printed-circuit
board.
• For L ≤ 19 mm capacitors shall be mechanically fixed by the leads
• For larger pitches the capacitors shall be mounted in the same way and the body clamped
• The maximum diameter and length of the capacitors are specified in the dimensions table
• Eccentricity as shown in the drawing below:
1 mm
Storage Temperature
• Storage temperature: Tstg = - 25 °C to + 40 °C with RH maximum 80 % without condensation
Ratings and Characteristics Reference Conditions
Unless otherwise specified, all electrical values apply to an ambient free air temperature of 23 °C 1 °C, an atmospheric pressure
of 86 kPa to 106 kPa and a relative humidity of 50 % 2 %.
For reference testing, a conditioning period shall be applied over 96 h 4 h by heating the products in a circulating air oven at
the rated temperature and a relative humidity not exceeding 20 %.
Document Number: 28162
Revision: 21-Apr-10
For technical questions, contact: dc-film@vishay.com
www.vishay.com
261
MKP 1839 HQ
AC and Pulse Metallized Polypropylene Film Capacitors
MKP Axial Type
Vishay Roederstein
CHARACTERISTICS
Capacitance as a function of ambient temperature (typical curve)
Tangent of loss angle as a function of frequency (typical curve)
103
4
2
0
102
3.3 µF
1.0 µF
0.1 µF
- 2
- 4
- 6
101
100
102
f (Hz)
103
104
105
106
- 60 - 40 - 20
0
20
40
60
80
100
120
Tamb (°C)
Impedance as a function of frequency (typical curve)
Max. DC and AC voltage as a function of temperature
103
102
1.2
1
Capacitance in µF
0.1 µF
101
100
0.8
0.22 µF
0.47 µF
1.0 µF
0.6
0.4
0.2
0
3.3 µF
10-1
10-2
10-3
104
f (Hz)
105
106
107
108
- 60
- 20
20
60
100
Tamb (°C)
Max. RMS Voltage (sinewave) as a function of frequency
Max. RMS Voltage (sinewave) as a function of frequency
103
103
102
101
100
102
101
100
0.1 µF
0.22 µF
0.47 µF
0.1 µF
0.22 µF
0.47 µF
1.0 µF
3.3 µF
1.0 µF
3.3 µF
Tamb ≤ 85 °C, 630 VDC
85 °C < Tamb ≤ 110 °C, 630 VDC
102
f (Hz)
102
103
104
105
106
107
103
104
105
106
f (Hz)
107
www.vishay.com
262
For technical questions, contact: dc-film@vishay.com
Document Number: 28162
Revision: 21-Apr-10
MKP 1839 HQ
AC and Pulse Metallized Polypropylene Film Capacitors
MKP Axial Type
Vishay Roederstein
Max. RMS Voltage (sinewave) as a function of frequency
Max. RMS Voltage (sinewave) as a function of frequency
103
103
102
101
100
102
101
100
0.1 µF
0.22 µF
0.47 µF
1.0 µF
0.1 µF
0.22 µF
0.47 µF
1.0 µF
Tamb ≤ 85 °C, 850 VDC
85 °C < Tamb ≤ 110 °C, 850 VDC
102
f (Hz)
102
103
104
105
106
107
107
107
103
104
105
106
f (Hz)
107
107
107
Max. RMS Voltage (sinewave) as a function of frequency
Max. RMS Voltage (sinewave) as a function of frequency
103
103
102
101
100
102
101
100
0.1 µF
0.22 µF
0.47 µF
1.0 µF
0.1 µF
0.22 µF
0.47 µF
1.0 µF
Tamb ≤ 85 °C, 1250 VDC
85 °C < Tamb ≤ 110 °C, 1250 VDC
102
f (Hz)
102
103
104
105
106
103
104
105
106
f (Hz)
Max. RMS Voltage (sinewave) as a function of frequency
Max. RMS Voltage (sinewave) as a function of frequency
103
103
102
101
100
102
101
100
0.1 µF
0.22 µF
0.47 µF
0.1 µF
0.22 µF
0.47 µF
Tamb ≤ 85 °C, 1600 VDC
85 °C < Tamb ≤ 110 °C, 1600 VDC
102
f (Hz)
102
103
104
105
106
103
104
105
106
f (Hz)
Document Number: 28162
Revision: 21-Apr-10
For technical questions, contact: dc-film@vishay.com
www.vishay.com
263
MKP 1839 HQ
AC and Pulse Metallized Polypropylene Film Capacitors
MKP Axial Type
Vishay Roederstein
Max. allowed component rise (ΔT) as a function of the ambient
temperature (Tamb
Insulation resistance as a function of ambient temperature
(typical curve)
)
106
12
10
8
6
4
2
0
105
104
- 60
- 20
20
60
100
0
30
60
90
120
Tamb (°C)
Tamb (°C)
HEAT CONDUCTIVITY (G) AS A FUNCTION OF CAPACITOR BODY THICKNESS IN mW/°C
HEAT CONDUCTIVITY (mW/°C)
DIAMETER
(mm)
PITCH 26.5 mm
PITCH 31.5 mm
7.0
8
10
11
12
13
-
-
8.0
-
8.5
12
-
9.5
10.0
10.5
11.0
11.5
12.0
12.5
13.0
13.5
14.0
15.0
16.0
16.5
18.0
19.0
19.5
20.0
21.5
23.0
23.5
24.0
25.5
28.0
15
16
17
18
19
20
21
22
23
25
28
29
32
34
36
37
40
44
45
47
51
57
15
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
www.vishay.com
264
For technical questions, contact: dc-film@vishay.com
Document Number: 28162
Revision: 21-Apr-10
MKP 1839 HQ
AC and Pulse Metallized Polypropylene Film Capacitors
MKP Axial Type
Vishay Roederstein
POWER DISSIPATION AND MAXIMUM COMPONENT TEMPERATURE RISE
The power dissipation must be limited in order not to exceed the maximum allowed component temperature rise as a function of
the free air ambient temperature.
The power dissipation can be calculated according type detail specification “HQN-384-01/101: Technical Information Film
Capacitors with the typical tgd of the curves”.
The component temperature rise (ΔT) can be measured (see section “Measuring the component temperature” for more details)
or calculated by ΔT = P/G:
• ΔT = Component temperature rise (°C)
• P = Power dissipation of the component (mW)
• G = Heat conductivity of the component (mW/°C)
MEASURING THE COMPONENT TEMPERATURE
A thermocouple must be attached to the capacitor body as in:
Thermocouple
The temperature is measured in unloaded (Tamb) and maximum loaded condition (TC).
The temperature rise is given by ΔT = TC - Tamb
.
To avoid radiation or convection, the capacitor should be tested in a wind-free.
APPLICATION NOTE AND LIMITING CONDITIONS
These capacitors are not suitable for mains applications as across-the-line capacitors without additional protection, as described
hereunder. These mains applications are strictly regulated in safety standards and therefore electromagnetic interference
suppression capacitors conforming the standards must be used.
To select the capacitor for a certain application, the following conditions must be checked:
1. The peak voltage (UP) shall not be greater than the rated DC voltage (URDC
)
2. The peak-to-peak voltage (UP-P) shall not be greater than the maximum (UP-P) to avoid the ionisation inception level
3. The voltage pulse slope (dU/dt) shall not exceed the rated voltage pulse slope in an RC-circuit at rated voltage and without
ringing. If the pulse voltage is lower than the rated DC voltage, the rated voltage pulse slope may be multiplied by URDC and
divided by the applied voltage.
For all other pulses following equation must be fulfilled:
T
dU
-------
dU
-------
⎛
⎝
⎞
⎠
⎛
⎝
⎞
⎠
2 ×
2 × dt < URdc
×
∫
dt
dt
rated
0
T is the pulse duration.
4. The maximum component surface temperature rise must be lower than the limits (see figure max. allowed component
temperature rise).
5. Since in circuits used at voltages over 280 V peak-to-peak the risk for an intrinsically active flammability after a capacitor
breakdown (short circuit) increases, it is recommended that the power to the component is limited to 100 times the values
mentioned in the table “Heat conductivity”.
6. When using these capacitors as across-the-line capacitor in the input filter for mains applications or as series connected with
an impedance to the mains the applicant must guarantee that the following conditions are fulfilled in any case (spikes and
surge voltages from the mains included).
Document Number: 28162
Revision: 21-Apr-10
For technical questions, contact: dc-film@vishay.com
www.vishay.com
265
MKP 1839 HQ
AC and Pulse Metallized Polypropylene Film Capacitors
MKP Axial Type
Vishay Roederstein
Voltage Conditions for 6 Above
ALLOWED VOLTAGES
Tamb ≤ 85 °C
85 °C < Tamb ≤ 110 °C
See “Maximum AC voltage as a
function of temperature par.
characteristics”
Maximum continuous RMS voltage
URAC
0.875 x URAC
1.1 x URDC
Maximum temporary RMS-overvoltage (< 24 h)
Maximum peak voltage (VO-P) (< 2 s)
1.25 x URAC
1.6 x URDC
INSPECTION REQUIREMENTS
General Notes:
Sub-clause numbers of tests and performance requirements refer to the “Sectional Specification, Publication IEC 60384-17 and
Specific Reference Data”.
Group C Inspection Requirements
SUB-CLAUSE NUMBER AND TEST
CONDITIONS
PERFORMANCE REQUIREMENTS
SUB-GROUP C1A PART OF SAMPLE
OF SUB-GROUP C1
4.1
Dimensions (detail)
As specified in chapter “General Data” of this
specification
4.3.1
4.3
Initial measurements
Capacitance
Tangent of loss angle at 100 kHz
Robustness of terminations
Resistance to soldering heat
Tensile: Load 30 N; 10 s
Bending: Load 15 N; 90°
No visible damage
4.4
No pre-drying
Method: 1A
Solder bath: 280 °C 5 °C
Duration: 10 s
4.4.2
Final measurements
Visual examination
No visible damage
Legible marking
Capacitance
|ΔC/C| ≤ 2 % of the value measured initially
Tangent of loss angle
Increase of tan δ:
For C ≤ 470 nF ≤ 0.001 (10 x 10-4)
For C > 470 nF ≤ 0.0015 (15 x 10-4)
Compared to values measured initially
Insulation resistance
≥ 50 % of values specified in section
“Insulation Resistance” of this specification
4.14
Solvent resistance of the marking
Isopropylalcohol at room temperature
Method: 1
No visible damage
Legible marking
Rubbing material: Cotton wool
Immersion time: 5 min 0.5 min
SUB-GROUP C1B PART OF SAMPLE
OF SUB-GROUP C1
4.6.1
Initial measurements
Capacitance
Tangent of loss angle at 100 kHz
4.6
Rapid change of temperature
θA = - 55 °C
θB = + 110 °C
5 cycles
Duration t = 30 min
Visual examination
No visible damage
www.vishay.com
266
For technical questions, contact: dc-film@vishay.com
Document Number: 28162
Revision: 21-Apr-10
MKP 1839 HQ
AC and Pulse Metallized Polypropylene Film Capacitors
MKP Axial Type
Vishay Roederstein
SUB-CLAUSE NUMBER AND TEST
CONDITIONS
PERFORMANCE REQUIREMENTS
4.7
Vibration
Mounting:
See section “Mounting” of this specification
Procedure B4
Frequency range: 10 Hz to 55 Hz
Amplitude: 0.75 mm or
Acceleration 98 m/s²
(whichever is less severe)
Total duration 6 h
4.7.2
4.9
Final inspection
Shock
Visual examination
No visible damage
Mounting:
See section “Mounting” for more information
Pulse shape: Half sine
Acceleration: 490 m/s²
Duration of pulse: 11 ms
4.9.3
Final measurements
Visual examination
Capacitance
No visible damage
|ΔC/C| ≤ 2 % of the value measured initally
Tangent of loss angle
Increase of tan δ:
For C ≤ 470 nF ≤ 0.001 (10 x 10-4)
For C > 470 nF ≤ 0.0015 (15 x 10-4)
Compared to values measured initially
Insulation resistance
≥ 50 % of values specified in section
“Insulation Resistance” of this specification
SUB-GROUP C1 COMBINED SAMPLE
OF SPECIMENS OF SUB-GROUPS
C1A AND C1B
4.10
Climatic sequence
4.10.2 Dry heat
Temperature: 110 °C
Duration: 16 h
4.10.3 Damp heat cyclic
Test Db, first cycle
4.10.4 Cold
Temperature: - 55 °C
Duration: 2 h
4.10.6 Damp heat cyclic
Test Db, remaining cycles
4.10.6.2 Final measurements
Voltage proof = URDC for 1 min within
15 min after removal from testchambers
No breakdown or flashover
Visual examination
No visible damage
Legible marking
Capacitance
|ΔC/C| ≤ 3 % of the value measured initially
Tangent of loss angle
Increase of tan δ:
For C ≤ 470 nF ≤ 0.001 (10 x 10-4)
For C > 470 nF ≤ 0.0015 (15 x 10-4)
Compared to values measured in
4.3.1 or 4.6.1 as applicable
Insulation resistance
≥ 50 % of values specified in section
“Insulation Resistance” of this specification
SUB-GROUP C2
4.11
Damp heat steady state
Capacitance
4.11.1 Initial measurements
Tangent of loss angle at 1 kHz
Visual examination
No visible damage
Legible marking
4.11.3 Final measurements
Voltage proof = URDC for 1 min within
15 min after removal from testchamber
No breakdown or flashover
Capacitance
|ΔC/C| ≤ 3 % of the value measured in
4.11.1.
Tangent of loss angle
Increase of tan δ:
For C ≤ 470 nF ≤ 0.001 (10 x 10-4)
For C > 470 nF ≤ 0.0015 (15 x 10-4)
Compared to values measured in 4.11.1
Insulation resistance
≥ 50 % of values specified in section
“Insulation Resistance” of this specification
Document Number: 28162
Revision: 21-Apr-10
For technical questions, contact: dc-film@vishay.com
www.vishay.com
267
MKP 1839 HQ
AC and Pulse Metallized Polypropylene Film Capacitors
MKP Axial Type
Vishay Roederstein
SUB-CLAUSE NUMBER AND TEST
SUB-GROUP C3 A
CONDITIONS
PERFORMANCE REQUIREMENTS
4.12.1 Endurance test at 50 Hz
alternative voltage
Duration: 2000 h
x URDC at 85 °C
0.875x URDC at 110 °C
4.12.1.1 Initial measurements
4.12.1.3 Final measurements
Capacitance
Tangent of loss angle at 100 kHz
Visual examination
No visible damage
Legible marking
Capacitance
|ΔC/C| ≤ 5 % compared to values measured
in 4.12.1.1
Increase of tan δ:
Tangent of loss angle
For C ≤ 470 nF ≤ 0.001 (10 x 10-4)
For C > 470 nF ≤ 0.0015 (15 x 10-4)
Compared to values measured in 4.12.1.1
Insulation resistance
≥ 50 % of values specified in section
“Insulation Resistance” of this specification
SUB-GROUP C4
4.2.6
Temperature characteristics
Initial measurement
Intermediate measurements
Capacitance
For - 55 °C to 20 °C
0 % ≤ |ΔC/C| ≤ 2.75 % or
for 20 °C to 110 °C:
- 5.5 % ≤ |ΔC/C| ≤ 0 %
As specified in section “Capacitance” of this
specification
Capacitance at - 55 °C
Capacitance at 20 °C
Capacitance at 110 °C
4.13
Charge and discharge
10 000 cycles
Charged to URDC
Discharge resistance:
Un(Vdc)
2.5 × C(dU ⁄ dt)
----------------------------------------
R =
4.13.1 Initial measurements
4.13.3 Final measurements
Capacitance
Tangent of loss angle at 100 kHz
Capacitance
|ΔC/C| ≤ 3 % of the value measured in 4.13.1
Increase of tan δ:
Tangent of loss angle
For C ≤ 470 nF ≤ 0.001 (10 x 10-4)
For C > 470 nF ≤ 0.0015 (15 x 10-4)
Compared to values measured in 4.13.1
Insulation resistance
≥ 50 % of values specified in section
“Insulation Resistance” of this specification
www.vishay.com
268
For technical questions, contact: dc-film@vishay.com
Document Number: 28162
Revision: 21-Apr-10
Legal Disclaimer Notice
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Document Number: 91000
Revision: 11-Mar-11
www.vishay.com
1
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明