首页 |元器件品牌

MKP3833471000JC2R0 [VISHAY]

AC and Pulse Double Metallized Polypropylene Film Capacitors;
MKP3833471000JC2R0
型号： MKP3833471000JC2R0
厂家： VISHAY    VISHAY
描述：

AC and Pulse Double Metallized Polypropylene Film Capacitors
文件： 总16页 (文件大小：165K)
中文：  中文翻译
下载：  下载PDF数据表文档文件
 查看货源
MKP383  
Vishay BCcomponents  
www.vishay.com  
AC and Pulse Double Metallized Polypropylene Film Capacitors  
MKP Radial Potted Type  
FEATURES  
• 7.5 mm to 37.5 mm lead pitch; 7.5 mm bent  
back pitch  
• Low contact resistance  
• Low loss dielectric  
• Small dimensions for high density packaging  
• Supplied loose in box and taped on reel or  
ammopack  
• Mounting: radial  
• Material categorization: for definitions of compliance  
please see www.vishay.com/doc?99912  
APPLICATIONS  
• Where steep pulses occur e.g. SMPS  
(switch mode power supplies)  
• Electronic lighting e.g. ballast  
• Motor control circuits  
• S-correction  
• For flyback applications please use 1400 V series  
QUICK REFERENCE DATA  
Capacitance range (E24 series)  
Capacitance tolerance  
Climatic testing class according to IEC 60068-1  
Rated DC temperature  
Rated AC temperature  
Maximum application temperature  
Reference specifications  
Dielectric  
0.00047 μF to 4.7 μF  
5 %  
55/105/56  
85 °C  
105 °C  
105 °C  
IEC 60384-17  
Polypropylene film  
Metallized  
Electrodes  
Construction  
Mono and internal serial construction  
Flame retardant plastic case and epoxy resin  
UL-class 94 V-0  
Encapsulation  
Leads  
Tinned wire  
C-value; tolerance; rated voltage; sub-class; manufacturer’s type; code for dielectric  
material; manufacturer location; manufacturer's logo; year and week  
Marking  
Note  
•
For more detailed data and test requirements, contact dc-film@vishay.com  
VOLTAGE RATINGS  
Rated DC voltage  
250  
125  
350  
400  
200  
560  
630  
220  
630  
1000  
350  
1400  
500  
1600  
550  
2000  
700  
2500  
900  
Rated AC voltage  
Rated peak to peak voltage  
1000  
1400  
1600  
2000  
2500  
Revision: 08-Aug-2018  
Document Number: 28173  
1
For technical questions, contact: dc-film@vishay.com  
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT  
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000  
MKP383  
Vishay BCcomponents  
www.vishay.com  
COMPOSITION OF CATALOG NUMBER  
Example  
Voltage (VDC  
)
P1 (mm)  
Pitch Code  
025 = 250  
040 = 400  
063 = 630  
100 = 1000  
140 = 1400  
160 = 1600  
200 = 2000  
250 = 2500  
5
B
C
D
F
I
147  
210  
310  
410  
470 pF  
1 nF  
0.00047 μF  
0.001 μF  
0.01 μF  
0.1 μF  
7.5  
10  
10 nF  
100 nF  
15  
22.5  
27.5  
37.5  
510 1000 nF  
610 10 000 nF  
1.0 μF  
K
P
10.0 μF  
Multiplier (nF)  
0.01  
0.1  
1
1
2
3
4
5
6
Capacitance Code  
Special Code for Terminal  
(numerically)  
2
4
2 pins  
10  
4 pins P2 = 10.2 mm  
4 pins P2 = 20.3 mm  
Customized  
100  
1000  
5
(#)  
1 2 3 4 5 6  
M K P 3 8 3  
7
1
8 9  
4 7  
10 11 12  
13  
14  
I
15  
16  
2
17  
18  
0
2
5
0
J
P
T
Special  
0 = Standard  
Type  
Tolerance  
Other = Special  
J
5 %  
A
Special tolerance  
It (mm)  
Lead Length Code  
Pitch (mm)  
Packing Code  
Packing Style  
Remark  
3.5 + 1.0/- 0.5  
3.5 0.3  
A
≤ 10  
≥ 15  
All  
B/T  
R
Bulk/loose (1)  
Excluding bent back  
For bent back only  
For bent back only  
For bent back only  
P
Tape and reel; (H: 16.0 mm; 500 mm)  
Tape and reel; (H: 16.0 mm; 356 mm)  
Ammo (H: 16.0 mm)  
5
1
M
Z
25  
2
I
All  
H
0: Space holder  
W
G
Tape and reel (H: 18.5 mm; 500 mm) Pitch 5 mm to 22.5 mm  
Ammo (H: 18.5 mm)  
Pitch ≤ 10 mm  
Notes  
•
For detailed tape specifications refer to packaging information www.vishay.com/doc?28139  
(1)  
Packaging will be bulk for all capacitors with pitch 15 mm and such with long leads (> 5 mm).  
Capacitors with short leads up to 5 mm and pitch > 15 mm will be in tray and asking code will be “T”.  
Revision: 08-Aug-2018  
Document Number: 28173  
2
For technical questions, contact: dc-film@vishay.com  
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT  
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000  
MKP383  
Vishay BCcomponents  
www.vishay.com  
ELECTRICAL DATA (For Detailed Ratings go to www.vishay.com/doc?28183)  
URDC  
(V)  
CAP.  
(μF)  
0.0068 min.  
2.7 max.  
250  
400  
0.0047 min.  
1.5 max.  
0.00047 min.  
4.7 max.  
630  
0.0043 min.  
1.8 max.  
1000  
1400  
1600  
2000  
2500  
0.0022 min.  
0.68 max.  
0.0027 min.  
0.56 max.  
0.0010 min.  
0.56 max.  
0.0010 min.  
0.3 max.  
DIMENSIONS in millimeters  
l
l
w
w
h
h
h'  
F'  
l
t
(1)  
F
Ø d  
H
t
P
10  
Ø d  
t
15  
I
w
Marking  
h
Ø dt  
6 -2  
P1 0.5  
P2 0.5  
Note  
(1)  
| F-F' | < 0.3 mm  
F = 7.5 mm + 0.6 mm / - 0.1 mm  
Ø dt 10 % of standard diameter specified  
Revision: 08-Aug-2018  
Document Number: 28173  
3
For technical questions, contact: dc-film@vishay.com  
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT  
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000  
MKP383  
Vishay BCcomponents  
www.vishay.com  
MOUNTING  
Normal Use  
The capacitors are designed for mounting on printed-circuit boards. The capacitors packed in bandoliers are designed for  
mounting on printed-circuit boards by means of automatic insertion machines.  
For detailed tape specifications refer to packaging information www.vishay.com/doc?28139  
Specific Method of Mounting to Withstand Vibration and Shock  
In order to withstand vibration and shock tests, it must be ensured that the stand-off pips are in good contact with the  
printed-circuit board:  
• For original pitch = 15 mm the capacitors shall be mechanically fixed by the leads  
• For larger pitches the capacitors shall be mounted in the same way and the body clamped  
Space Requirements on Printed-Circuit Board  
The maximum space for length (lmax.), width (wmax.) and height (hmax.) of film capacitors to take in account on the printed circuit  
board is shown in the drawings.  
For products with pitch 15 mm, w = l = 0.3 mm and h = 0.1 mm  
For products with 15 mm < pitch 27.5 mm, w =l = 0.5 mm and h = 0.1 mm  
For products with pitch = 37.5 mm, w = l = 0.7 mm and h = 0.5 mm  
Eccentricity as in drawing. The maximum eccentricity is smaller than or equal to the lead diameter of the product concerned.  
wmax. = w + Δw  
Eccentricity  
Imax. = I + ΔI  
hmax. = h + Δh  
Seating plane  
SOLDERING CONDITIONS  
For general soldering conditions and wave soldering profile we refer to the document “Soldering Guidelines for Film  
Capacitors”: www.vishay.com/doc?28171  
STORAGE TEMPERATURE  
Tstg = -25 °C to +35 °C with RH maximum 75 % without condensation  
RATINGS AND CHARACTERISTICS REFERENCE CONDITIONS  
Unless otherwise specified, all electrical values apply to an ambient free temperature of 23 °C 1 °C, an atmospheric pressure  
of 86 kPa to 106 kPa and a relative humidity of 50 % 2 %.  
For reference testing, a conditioning period shall be applied over 96 h 4 h by heating the products in a circulating air oven at  
the rated temperature and a relative humidity not exceeding 20 %.  
Revision: 08-Aug-2018  
Document Number: 28173  
4
For technical questions, contact: dc-film@vishay.com  
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT  
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000  
MKP383  
Vishay BCcomponents  
www.vishay.com  
CHARACTERISTICS  
103  
102  
101  
100  
10-1  
4
1 kHz  
typical  
2
max.  
1 nF  
0
100 nF  
- 2  
2.2 µF  
4.7 µF  
- 4  
- 6  
10-2  
10-3  
min.  
104  
105  
106  
107  
108  
- 60  
- 20  
20  
60  
Tamb (°C) 100  
f (Hz)  
Capacitance as a function of ambient temperature (typical curve)  
(1 kHz)  
Impedance as a function of frequency (typical curve)  
1.2  
1.0  
0.8  
0.6  
0.4  
0.2  
0.0  
100  
- 50  
- 20  
20  
60  
Tamb (°C)  
Max. DC and AC voltage as a function of temperature  
103  
103  
85 °C < Tamb ≤ 105 °C, 250 VDC  
Tamb  
≤
85 °C, 250 VDC  
100 nF  
100 nF  
220 nF  
470 nF  
1.0 μF  
2.2 μF  
220 nF  
470 nF  
1.0 μF  
2.2 μF  
102  
102  
101  
102  
101  
103  
104  
105  
106  
f (Hz)  
107  
103  
104  
105  
106  
107  
f (Hz)  
Max. RMS voltage as a function of frequency  
Max. RMS voltage as a function of frequency  
Revision: 08-Aug-2018  
Document Number: 28173  
5
For technical questions, contact: dc-film@vishay.com  
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT  
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000  
MKP383  
Vishay BCcomponents  
www.vishay.com  
103  
103  
85 °C < Tamb  
≤ 105 °C, 400 VDC  
Tamb ≤ 85 °C, 400 VDC  
47 nF  
100 nF  
470 nF  
1.0 μF  
47 nF  
100 nF  
470 nF  
1.0 μF  
102  
102  
101  
101  
102  
103  
104  
105  
106  
107  
107  
107  
103  
104  
105  
106  
107  
107  
107  
f (Hz)  
f (Hz)  
f (Hz)  
f (Hz)  
Max. RMS voltage as a function of frequency  
Max. RMS voltage as a function of frequency  
103  
103  
85 °C < Tamb ≤ 105 °C, 630 VDC  
Tamb ≤ 85 °C, 630 VDC  
47 nF  
100 nF  
220 nF  
470 nF  
1.0 μF  
4.7 μF  
47 nF  
100 nF  
220 nF  
470 nF  
1.0 μF  
4.7 μF  
102  
102  
101  
101  
103  
104  
105  
106  
102  
103  
104  
105  
106  
f (Hz)  
Max. RMS voltage as a function of frequency  
Max. RMS voltage as a function of frequency  
103  
103  
Tamb ≤ 85 °C, 1000 VDC  
85 °C < Tamb  
≤
105 °C, 1000 VDC  
4.7 nF  
10 nF  
47 nF  
220 nF  
1.0 μF  
4.7 nF  
10 nF  
47 nF  
220 nF  
1.0 μF  
102  
102  
101  
101  
103  
104  
105  
106  
102  
103  
104  
105  
106  
f (Hz)  
Max. RMS voltage as a function of frequency  
Max. RMS voltage as a function of frequency  
Revision: 08-Aug-2018  
Document Number: 28173  
6
For technical questions, contact: dc-film@vishay.com  
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT  
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000  
MKP383  
Vishay BCcomponents  
www.vishay.com  
103  
103  
Tamb ≤ 85 °C, 1400 VDC  
85 °C < Tamb  
≤
105 °C, 1400 VDC  
2.2 nF  
4.7 nF  
22 nF  
100 nF  
470 nF  
2.2 nF  
4.7 nF  
22 nF  
100 nF  
470 nF  
102  
102  
101  
101  
103  
104  
105  
106  
107  
107  
107  
102  
103  
104  
105  
106  
107  
f (Hz)  
f (Hz)  
Max. RMS voltage as a function of frequency  
Max. RMS voltage as a function of frequency  
103  
103  
85 °C < Tamb  
≤
105 °C, 1600 VDC  
Tamb ≤ 85 °C, 1600 VDC  
4.7 nF  
10 nF  
47 nF  
100 nF  
470 nF  
4.7 nF  
10 nF  
47 nF  
100 nF  
470 nF  
102  
102  
101  
101  
103  
104  
105  
106  
102  
103  
104  
105  
106  
107  
f (Hz)  
f (Hz)  
Max. RMS voltage as a function of frequency  
Max. RMS voltage as a function of frequency  
103  
103  
85 °C < Tamb  
≤
105 °C, 2000 VDC  
1 nF  
2.2 nF  
10 nF  
47 nF  
100 nF  
470 nF  
1 nF  
2.2 nF  
10 nF  
47 nF  
100 nF  
470 nF  
102  
102  
Tamb ≤ 85 °C, 2000 VDC  
101  
101  
103  
104  
105  
106  
102  
103  
104  
105  
106  
107  
f (Hz)  
f (Hz)  
Max. RMS voltage as a function of frequency  
Max. RMS voltage as a function of frequency  
Revision: 08-Aug-2018  
Document Number: 28173  
7
For technical questions, contact: dc-film@vishay.com  
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT  
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000  
MKP383  
Vishay BCcomponents  
www.vishay.com  
103  
103  
1 nF  
2.2 nF  
4.7 nF  
10 nF  
22 nF  
220 nF  
1 nF  
2.2 nF  
4.7 nF  
10 nF  
22 nF  
220 nF  
102  
102  
Tamb ≤ 85 °C, 2500 VDC  
104 105  
85 °C < Tamb  
≤
105 °C, 2500 VDC  
104  
101  
101  
103  
106  
107  
108  
f (Hz)  
102  
103  
105  
106  
107  
f (Hz)  
Max. RMS voltage as a function of frequency  
Max. RMS voltage as a function of frequency  
106  
12  
8
105  
4
104  
0
0
20  
40  
60  
80  
- 50  
- 20  
20  
60  
100  
Tamb (°C)  
100  
amb (°C)  
T
Maximum allowed component temperature rise (T)  
as a function of the ambient temperature (Tamb  
Insulation resistance as a function of the ambient temperature  
)
Revision: 08-Aug-2018  
Document Number: 28173  
8
For technical questions, contact: dc-film@vishay.com  
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT  
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000  
MKP383  
Vishay BCcomponents  
www.vishay.com  
1000  
100  
10  
16  
15  
14  
13  
12  
11  
10  
9
8
20  
19  
18  
17  
7
6
5
4
3
2
1
21  
1
102  
103  
104  
105  
106  
f (Hz)  
Tangent of loss angle as a function of frequency (typical curve)  
250 V:  
400 V:  
630 V:  
1000 V:  
0.0068 C 0.091 μF, curve 8  
0.1 < C 0.15 μF, curve 9  
0.15 < C 0.22 μF, curve 10  
0.22 < C 0.27 μF, curve 11  
0.27 < C 0.33 μF, curve 12  
0.33 < C 0.56 μF, curve 15  
0.56 < C 0.82 μF, curve 16  
0.82 < C 1.2 μF, curve 18  
1.2 < C 1.6 μF, curve 19  
1.6 < C 2.7 μF, curve 20  
0.0047 < C 0.047 μF, curve 5  
0.047 < C 0.068 μF, curve 6  
0.068 < C 0.1 μF, curve 7  
0.1 < C 0.2 μF, curve 8  
0.00047 < C 0.033 μF, curve 4 C 0.01 μF, curve 2  
0.033 < C 0.068 μF, curve 5  
0.068 < C 0.1 μF, curve 6  
0.1 < C 0.15 μF, curve 7  
0.15 < C 0.22 μF, curve 11  
0.22 < C 0.27 μF, curve 12  
0.27 < C 0.33 μF, curve 15  
0.33 < C 0.82 μF, curve 16  
0.82 < C 1 μF, curve 18  
1 < C 4.7 μF, curve 21  
0.011 < C 0.027 μF, curve 3  
0.027 < C 0.047 μF, curve 4  
0.047 < C 0.062 μF, curve 5  
0.062 < C 0.075 μF, curve 6  
0.075 < C 0.1 μF, curve 7  
0.1 < C 0.15 μF, curve 8  
0.15 < C 0.22 μF, curve 9  
0.22 < C 0.3 μF, curve 10  
0.3 < C 1 μF, curve 16  
0.2 < C 0.24 μF, curve 12  
0.24 < C 0.36 μF, curve 13  
0.36 < C 0.43 μF, curve 14  
0.43 < C 0.56 μF, curve 16  
0.56 < C 1.1 μF, curve 17  
1.1 < C 1.5 μF, curve 18  
1 < C 1.8 μF, curve 19  
1400 V:  
1600 V:  
2000 V:  
2500 V:  
C 0.0047 μF, curve 1  
C 0.0047 μF, curve 3  
C 0.0047 μF, curve 2  
C 0.0047 μF, curve 1  
0.0051 < C 0.015 μF, curve 2  
0.015 < C 0.091 μF, curve 3  
0.091 < C 0.33 μF, curve 12  
0.0051 < C 0.016 μF, curve 2  
0.016 < C 0.033 μF, curve 3  
0.033 < C 0.051 μF, curve 4  
0.051 < C 0.068 μF, curve 5  
0.068 < C 0.082 μF, curve 6  
0.082 < C 0.2 μF, curve 7  
0.2 < C 0.68 μF, curve 14  
0.0051 < C 0.0091 μF, curve 4 0.0051 < C 0.033 μF, curve 3  
0.0091 < C 0.068 μF, curve 5  
0.068 < C 0.01 μF, curve 6  
0.01 < C 0.16 μF, curve 7  
0.16 < C 0.56 μF, curve 14  
0.033 < C 0.091 μF, curve 4  
0.091 < C 0.56 μF, curve 14  
Revision: 08-Aug-2018  
Document Number: 28173  
9
For technical questions, contact: dc-film@vishay.com  
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT  
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000  
MKP383  
Vishay BCcomponents  
www.vishay.com  
HEAT CONDUCTIVITY (G) AS A FUNCTION OF (ORIGINAL) PITCH AND CAPACITOR BODY  
THICKNESS IN mW/°C  
HEAT CONDUCTIVITY (mW/°C)  
Wmax. (mm)  
PITCH 7.5 mm  
PITCH 10 mm  
PITCH 15 mm PITCH 22.5 mm PITCH 27.5 mm PITCH 37.5 mm  
3.0  
4.0  
4
5
5
6
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
6.5  
-
-
-
-
-
-
-
-
-
4.5  
-
-
-
5.0  
7.5  
9.0  
-
10  
11  
12  
16  
-
-
-
-
-
6.0  
19  
21  
25  
-
-
7.0  
-
-
8.5  
-
-
-
9.0  
-
31  
-
-
-
10.0  
11.0  
13.0  
15.0  
18.0  
18.5  
21.0  
21.5  
24.0  
30.0  
-
18  
-
28  
-
-
36  
42  
48  
57  
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
-
89  
-
-
-
-
68  
-
-
-
-
102  
116  
134  
-
-
-
-
-
-
-
-
POWER DISSIPATION AND MAXIMUM COMPONENT TEMPERATURE RISE  
The power dissipation must be limited in order not to exceed the maximum allowed component temperature rise as a function  
of the free air ambient temperature.  
The power dissipation can be calculated according type detail specification “HQN-384-01/101: Technical information film  
capacitors with the typical tgd of the curves.”.  
The component temperature rise (T) can be measured (see section “Measuring the component temperature” for more details)  
or calculated by T = P/G:  
• T = component temperature rise (°C)  
• P = power dissipation of the component (mW)  
• G = heat conductivity of the component (mW/°C)  
MEASURING THE COMPONENT TEMPERATURE  
A thermocouple must be attached to the capacitor body as in:  
Thermocouple  
The temperature is measured in unloaded (Tamb) and maximum loaded condition (Tc).  
The temperature rise is given by T = Tc - Tamb.  
To avoid radiation or convection, the capacitor should be tested in a wind-free box.  
Revision: 08-Aug-2018  
Document Number: 28173  
10  
For technical questions, contact: dc-film@vishay.com  
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT  
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000  
MKP383  
Vishay BCcomponents  
www.vishay.com  
APPLICATION NOTE AND LIMITING CONDITIONS  
For capacitors connected in parallel, normally the proof voltage and possibly the rated voltage must be reduced. For information  
depending of the capacitance value and the number of parallel connections contact: dc-film@vishay.com  
These capacitors are not suitable for mains applications as across-the-line capacitors without additional protection, as  
described hereunder. These mains applications are strictly regulated in safety standards and therefore electromagnetic  
interference suppression capacitors conforming the standards must be used.  
To select the capacitor for a certain application, the following conditions must be checked:  
1. The peak voltage (Up) shall not be greater than the rated DC voltage (URDC  
)
2. The peak-to-peak voltage (Up-p) shall not be greater than the maximum (Up-p) to avoid the ionization inception level  
3. The voltage pulse slope (dU/dt) shall not exceed the rated voltage pulse slope in an RC-circuit at rated voltage and without  
ringing. If the pulse voltage is lower than the rated DC voltage, the rated voltage pulse slope may be multiplied by URDC and  
divided by the applied voltage.  
For all other pulses following equation must be fulfilled:  
T
2
dU  
dt  
dU  
2 x  
------- x dt < URDC x -------  
dt  
rated  
0
T is the pulse duration  
4. The maximum component surface temperature rise must be lower than the limits (see graph max. allowed component  
temperature rise).  
5. Since in circuits used at voltages over 280 V peak-to-peak the risk for an intrinsically active flammability after a capacitor  
breakdown (short circuit) increases, it is recommended that the power to the component is limited to 100 times the values  
mentioned in the table: “Heat Conductivity”  
6. When using these capacitors as across-the-line capacitor in the input filter for mains applications or as series connected  
with an impedance to the mains the applicant must guarantee that the following conditions are fulfilled in any case (spikes  
and surge voltages from the mains included).  
VOLTAGE CONDITIONS FOR 6 ABOVE  
ALLOWED VOLTAGES  
T
amb ≤ 85 °C  
85 °C < Tamb ≤ 105 °C  
URAC  
Maximum continuous RMS voltage  
Maximum temperature RMS-over voltage (< 24 h)  
Maximum peak voltage (Vo-p) (< 2 s)  
URAC  
1.25 x URAC  
1.6 x URDC  
1.25 x URAC  
1.1 x URDC  
EXAMPLE  
C = 4n7 - 1600 V used for the voltage signal shown in next drawing.  
Up-p = 1000 V; Up = 900 V; T1 = 12 μs; T2 = 64 μs; T3 = 4 μs  
The ambient temperature is 80 °C. In case of failure, the oscillation is blocked.  
Checking conditions:  
1. The peak voltage Up = 900 V is lower than 1600 VDC  
2. The peak-to-peak voltage 1000 V is lower than 22 x 550 VAC = 1600 Up-p  
3. The voltage pulse slope (dU/dt) = 1000 V/4 μs = 250 V/μs. This is lower than 8000 V/μs (see specific reference data for each  
version).  
4. The dissipated power is 35 mW as calculated with fourier terms and typical tgd.  
The temperature rise for wmax. = 6.0 mm and pitch = 15 mm will be 35 mW / 11 mW/°C = 3.2 °C  
This is lower than 10 °C temperature rise at 80 °C, according graph.  
5. Oscillation is blocked  
6. Not applicable  
Revision: 08-Aug-2018  
Document Number: 28173  
11  
For technical questions, contact: dc-film@vishay.com  
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT  
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000  
MKP383  
Vishay BCcomponents  
www.vishay.com  
VOLTAGE SIGNAL  
Voltage  
Up  
Up-p  
Time  
T3  
T1  
T2  
INSPECTION REQUIREMENTS  
General Notes  
Sub-clause numbers of tests and performance requirements refer to the “Sectional Specification, Publication IEC 60384-17 and  
Specific Reference Data”.  
GROUP C INSPECTION REQUIREMENTS  
SUB-CLAUSE NUMBER AND TEST  
CONDITIONS  
PERFORMANCE REQUIREMENTS  
SUB-GROUP C1A PART OF SAMPLE  
OF SUB-GROUP C1  
4.1  
Dimensions (detail)  
As specified in chapters “General Data” of  
this specification  
4.3.1  
Initial measurements  
Capacitance  
Tangent of loss angle:  
for C 1 μF at 100 kHz or  
for C > 1 μF at 10 kHz  
4.3  
4.4  
Robustness of terminations  
Resistance to soldering heat  
Tensile: load 10 N; 10 s  
No visible damage  
Bending: load 5 N; 4 x 90°  
Method: 1A  
Solder bath: 280 °C 5 °C  
Duration: 10 s  
4.14  
Component solvent resistance  
Final measurements  
Isopropylalcohol at room temperature  
Method: 2  
Immersion time: 5 min 0.5 min  
Recovery time: min. 1 h, max. 2 h  
4.4.2  
Visual examination  
No visible damage  
Legible marking  
Capacitance  
|C/C| 1 % of the value measured initially  
Tangent of loss angle  
Increase of tan :  
0.0005 for: C 100 nF or  
0.001 for: 100 nF < C 470 nF or  
0.0015 for: C > 470 nF  
Compared to values measured in 4.3.1  
Revision: 08-Aug-2018  
Document Number: 28173  
12  
For technical questions, contact: dc-film@vishay.com  
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT  
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000  
MKP383  
Vishay BCcomponents  
www.vishay.com  
GROUP C INSPECTION REQUIREMENTS  
SUB-CLAUSE NUMBER AND TEST  
CONDITIONS  
PERFORMANCE REQUIREMENTS  
SUB-GROUP C1B OTHER PART OF  
SAMPLE OF SUB-GROUP C1  
4.6.1  
4.15  
4.6  
Initial measurements  
Capacitance  
Tangent of loss angle:  
for C 1 μF at 100 kHz or  
for C > 1 μF at 10 kHz  
Solvent resistance of the marking  
Rapid change of temperature  
Vibration  
Isopropylalcohol at room temperature   
Method: 1  
Rubbing material: cotton wool  
Immersion time: 5.0 min 0.5 min  
No visible damage  
Legible marking  
A = -55 °C  
B = +105 °C  
5 cycles  
Duration t = 30 min  
4.7  
Visual examination  
No visible damage  
Mounting: see section “Mounting” for more  
information  
Procedure B4  
Frequency range: 10 Hz to 55 Hz  
Amplitude: 0.75 mm or  
Acceleration 98 m/sꢀ  
(whichever is less severe)  
Total duration 6 h  
4.7.2  
4.9  
Final inspection  
Shock  
Visual examination  
No visible damage  
Mounting: see section “Mounting” for more  
information  
Pulse shape: half sine  
Acceleration: 490 m/sꢀ  
Duration of pulse: 11 ms  
4.9.3  
Final measurements  
Visual examination  
Capacitance  
No visible damage  
|C/C| 2 % for pitch < 10 mm  
|C/C| 1 % for pitch > 10 mm of the value  
measured in 4.6.1  
Tangent of loss angle  
Insulation resistance  
Increase of tan :  
0.0005 for: C 100 nF or  
0.001 for: 100 nF < C 470 nF or  
0.0015 for: C > 470 nF  
Compared to values measured in 4.6.1  
As specified in section “Insulation  
Resistance” of this specification  
Revision: 08-Aug-2018  
Document Number: 28173  
13  
For technical questions, contact: dc-film@vishay.com  
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT  
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000  
MKP383  
Vishay BCcomponents  
www.vishay.com  
GROUP C INSPECTION REQUIREMENTS  
SUB-CLAUSE NUMBER AND TEST  
CONDITIONS  
PERFORMANCE REQUIREMENTS  
SUB-GROUP C1  
COMBINED SAMPLE OF SPECIMENS OF  
SUB-GROUPS C1A and C1B  
4.10  
Climatic sequence  
4.10.2 Dry heat  
Temperature: +105 °C  
Duration: 16 h  
4.10.3 Damp heat cyclic  
Test Db, first cycle  
4.10.4 Cold  
Temperature: -55 °C  
Duration: 2 h  
4.10.6 Damp heat cyclic  
Test Db, remaining cycles  
4.10.6.2 Final measurements  
Voltage proof = URDC for 1 min within 15 min  
after removal from testchamber  
No breakdown or flash-over  
Visual examination  
Capacitance  
No visible damage  
Legible marking  
For original pitch = 22.5 mm and 37.5 mm:  
|C/C| 2 % or  
for original pitch 15 mm:  
|C/C| 3 % of the value measured in   
4.4.2 or 4.9.3  
Tangent of loss angle  
Insulation resistance  
Increase of tan :  
0.0005 for: C 100 nF or  
0.001 for: 100 nF < C 470 nF or  
0.0015 for: C > 470 nF  
Compared to values measured in  
4.3.1 or 4.6.1  
50 % of values specified in section  
“Insulation Resistance” of this specification  
SUB-GROUP C2  
4.11  
Damp heat steady state  
56 days, 40 °C, 90 % to 95 % RH   
no load  
4.11.1 Initial measurements  
4.11.3 Final measurements  
Capacitance  
Tangent of loss angle at 1 kHz  
Voltage proof = URDC for 1 min within 15 min  
after removal from testchamber  
No breakdown or flash-over  
Visual examination  
No visible damage  
Legible marking  
Capacitance  
|C/C| 1 % of the value measured in 4.11.1  
Tangent of loss angle  
Increase of tan :  
0.0005 for: C 100 nF or  
0.001 for: 100 nF < C 470 nF or  
0.0015 for: C > 470 nF  
Compared to values measured in 4.11.1  
Insulation resistance  
50 % of values specified in section  
“Insulation Resistance” of this specification  
Revision: 08-Aug-2018  
Document Number: 28173  
14  
For technical questions, contact: dc-film@vishay.com  
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT  
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000  
MKP383  
Vishay BCcomponents  
www.vishay.com  
GROUP C INSPECTION REQUIREMENTS  
SUB-CLAUSE NUMBER AND TEST  
SUB-GROUP C3A  
CONDITIONS  
PERFORMANCE REQUIREMENTS  
4.12.1 Endurance test at 50 Hz alternatingDuration: 2000 h  
voltage  
4.12.1.1 Initial measurements  
Voltage:  
1.25 x URAC at 105 °C  
Capacitance  
Tangent of loss angle:  
for C 1 μF at 100 kHz or  
for C > 1 μF at 10 kHz  
4.12.1.3 Final measurements  
Visual examination  
Capacitance  
No visible damage  
Legible marking  
|C/C| 5 % compared to values measured  
in 4.12.1.1  
Tangent of loss angle  
Increase of tan :  
0.0005 for: C 100 nF or  
0.001 for: 100 nF < C 470 nF or  
0.0015 for: C > 470 nF  
Compared to values measured in 4.12.1.1  
Insulation resistance  
50 % of values specified in section  
“Insulation Resistance” of this specification  
SUB-GROUP C4  
4.2.6  
Temperature charcteristics  
Initial measurements  
Intermediate measurements  
Capacitance   
For -55 °C to +20 °C:  
+1 % |C/C| 3.75 % or   
for 20 °C to 105 °C:  
Capacitance at -55 °C  
Capacitance at +20 °C  
Capacitance at +105 °C  
-6 % |C/C| 0 %  
Final measurements  
Charge and discharge  
Capacitance  
As specified in section “Capacitance” of this  
specification.  
Insulation resistance  
As specified in section “Insulation  
Resistance” of this specification  
4.13  
10 000 cycles  
Charged to URDC  
Discharge resistance:  
URDC  
R = --------------------------------------------  
5 x C x dU/dt  
4.13.1 Initial measurements  
4.13.3 Final measurements  
Capacitance  
Tangent of loss angle:  
for C 1 μF at 100 kHz or  
for C > 1 μF at 10 kHz  
Capacitance  
|C/C| 1 % compared to values measured  
in 4.13.1  
Tangent of loss angle  
Increase of tan :  
0.0005 for: C 100 nF or  
0.001 for: 100 nF < C 470 nF or  
0.0015 for: C > 470 nF  
Compared to values measured in 4.13.1  
Insulation resistance  
50 % of values specified in section  
“Insulation Resistance” of this specification  
Revision: 08-Aug-2018  
Document Number: 28173  
15  
For technical questions, contact: dc-film@vishay.com  
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT  
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000  
Legal Disclaimer Notice  
www.vishay.com  
Vishay  
Disclaimer  
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE  
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.  
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,  
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other  
disclosure relating to any product.  
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or  
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all  
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,  
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular  
purpose, non-infringement and merchantability.  
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of  
typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding  
statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a  
particular product with the properties described in the product specification is suitable for use in a particular application.  
Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over  
time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s  
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,  
including but not limited to the warranty expressed therein.  
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining  
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.  
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.  
Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for  
such applications.  
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document  
or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.  
© 2021 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED  
Revision: 01-Jan-2021  
Document Number: 91000  
1

相关型号：

SI9130DB

 5- and 3.3-V Step-Down Synchronous Converters

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135LG-T1

 SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135LG-T1-E3

 SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135_11

 SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9136_11

 Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130CG-T1-E3

 Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130LG-T1-E3

 Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130_11

 Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137

 Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137DB

 Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137LG

 Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9122E

 500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification Drivers

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明