首页 |元器件品牌

MKT1817222404D [VISHAY]

CAP FILM 2200PF 5% 400VDC RADIAL;
MKT1817222404D
型号： MKT1817222404D
厂家： VISHAY    VISHAY
描述：

CAP FILM 2200PF 5% 400VDC RADIAL
文件： 总14页 (文件大小：166K)
中文：  中文翻译
下载：  下载PDF数据表文档文件
 查看货源
Not for New Designs - Alternative Device: MKT370  
MKT1817  
Vishay Roederstein  
www.vishay.com  
Metallized Polyester Film Capacitors  
MKT Radial Potted Types  
FEATURES  
• Material categorization:  
for definitions of compliance please see  
www.vishay.com/doc?99912  
APPLICATIONS  
Blocking, bypassing, filtering and timing, high  
frequency coupling and decoupling for fast  
digital and analog ICs, interference suppression  
in low voltage applications.  
QUICK REFERENCE DATA  
Capacitance range  
1 nF to 1.0 μF (E12 series)  
Capacitance tolerance  
20 % (M), 10 % (K), ꢀ % (J)  
ꢀꢀ/100/ꢀ6 for rated voltage 63 V  
ꢀꢀ/10ꢀ/ꢀ6 for rated voltage > 63 V  
Climatic testing class according to IEC 60068-1  
Reference specifications  
Dielectric  
IEC 60384-2  
Polyester film  
Metallized  
Electrodes  
Mono construction  
Construction  
Encapsulation  
Leads  
Flame retardant plastic case and epoxy resin sealed (UL-class 94 V-0)  
Tinned wire  
Manufacturer’s logo/type/C-value/rated voltage/tolerance/date of manufacture  
63 VDC, 100 VDC, 2ꢀ0 VDC, 400 VDC  
Marking  
Rated DC voltage  
Rated AC voltage  
Rated temperature  
40 VAC, 63 VAC, 160 VAC, 200 VAC  
8ꢀ °C  
100 °C for rated voltage 63 V  
10ꢀ °C for rated voltage > 63 V  
Maximum application temperature  
Performance grade  
1 (long life)  
Note  
•
For more detailed data and test requirements, contact dc-film@vishay.com  
DIMENSIONS in millimeters  
l
w
h
lt = 6 - 1  
Ø 0.ꢀ 0.0ꢀ  
ꢀ.0 0.3  
Revision: 11-Jan-18  
Document Number: 26032  
1
For technical questions, contact: dc-film@vishay.com  
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT  
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000  
Not for New Designs - Alternative Device: MKT370  
MKT1817  
Vishay Roederstein  
www.vishay.com  
COMPOSITION OF CATALOG NUMBER  
CAPACITANCE  
(numerically)  
MULTIPLIER  
(nF)  
0.1  
1
2
3
4
ꢀ
Example:  
468 = 680 nF  
10  
100  
MKT 1817 X  
XX 2ꢀ  
X
X
PACKAGING  
Ammo, H = 18.ꢀ mm  
Reel H = 18.ꢀ mm, diameter 3ꢀ0 mm  
Bulk  
G
W
-
TYPE  
TOLERANCE  
Un = 06 = 63 V  
4
ꢀ
6
ꢀ %  
10 %  
20 %  
Un = 01 = 100 V  
Un = 2ꢀ = 2ꢀ0 V  
Un = 40 = 400 V  
SPECIFIC REFERENCE DATA  
DESCRIPTION  
VALUE  
Tangent of loss angle:  
C 0.1 μF  
at 1 kHz  
at 10 kHz  
at 100 kHz  
2ꢀ0 x 10-4  
-
80 x 10-4  
80 x 10-4  
1ꢀ0 x 10-4  
1ꢀ0 x 10-4  
0.1 μF < C 1.0 μF  
RATED VOLTAGE PULSE SLOPE (dU/dt)R AT  
PITCH  
(mm)  
63 VDC  
100 VDC  
250 VDC  
400 VDC  
ꢀ
60  
110  
330  
630  
If the maximum pulse voltage is less than the rated voltage higher dV/dt values can be permitted.  
R between leads, for C 0.33 μF and UR 100 V  
R between leads, for C 0.33 μF and UR > 100 V  
RC between leads, for C > 0.33 μF and UR 100 V  
RC between leads, for C > 0.33 μF and UR > 100 V  
> 1ꢀ 000 M  
> 30 000 M  
> ꢀ000 s  
> 10 000 s  
R between interconnecting leads and casing 100 V  
(foil method)  
> 30 000 M  
Withstanding (DC) voltage (cut off current 10 mA) (1);  
rise time 1000 V/s  
1.6 x URDC, 1 min  
Withstanding (DC) voltage between leads and case  
2.0 x URDC, with minimum of 200 VDC; 1 min  
100 °C for rated voltage 63 V  
10ꢀ °C for rated voltage > 63 V  
Maximum application temperature  
Note  
(1)  
See “Voltage Proof Test for Metalized Film Capacitors”: www.vishay.com/doc?28169  
Revision: 11-Jan-18  
Document Number: 26032  
2
For technical questions, contact: dc-film@vishay.com  
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT  
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000  
Not for New Designs - Alternative Device: MKT370  
MKT1817  
Vishay Roederstein  
www.vishay.com  
ELECTRICAL DATA  
DIMENSIONS  
URDC  
(V)  
CAP.  
(μF)  
CAPACITANCE  
CODE  
VOLTAGE CODE  
VAC  
w x h x l  
(mm)  
0.10  
0.1ꢀ  
0.22  
0.33  
0.47  
-410  
-41ꢀ  
-422  
-433  
-447  
-468  
-ꢀ10  
-322  
-333  
-347  
-368  
-410  
-41ꢀ  
-422  
-433  
-233  
-247  
-268  
-310  
-31ꢀ  
-322  
-333  
-347  
-368  
-410  
-233  
-247  
-268  
-310  
-31ꢀ  
-322  
-333  
-347  
-368  
-410  
-210  
-21ꢀ  
-222  
-233  
-247  
-268  
-310  
-31ꢀ  
-322  
2.ꢀ x 6.ꢀ x 7.2  
2.ꢀ x 6.ꢀ x 7.2  
3.ꢀ x 8.0 x 7.2  
3.ꢀ x 8.0 x 7.2  
3.ꢀ x 8.0 x 7.2  
4.ꢀ x 9.0 x 7.2  
6.0 x 11.0 x 7.2  
2.ꢀ x 6.ꢀ x 7.2  
2.ꢀ x 6.ꢀ x 7.2  
2.ꢀ x 6.ꢀ x 7.2  
2.ꢀ x 6.ꢀ x 7.2  
2.ꢀ x 6.ꢀ x 7.2  
3.ꢀ x 8.0 x 7.2  
4.ꢀ x 9.0 x 7.2  
4.ꢀ x 9.0 x 7.2  
2.ꢀ x 6.ꢀ x 7.2  
2.ꢀ x 6.ꢀ x 7.2  
2.ꢀ x 6.ꢀ x 7.2  
2.ꢀ x 6.ꢀ x 7.2  
2.ꢀ x 6.ꢀ x 7.2  
3.ꢀ x 8.0 x 7.2  
3.ꢀ x 8.0 x 7.2  
4.ꢀ x 9.0 x 7.2  
6.0 x 11.0 x 7.2  
6.0 x 11.0 x 7.2  
2.ꢀ x 6.ꢀ x 7.2  
2.ꢀ x 6.ꢀ x 7.2  
2.ꢀ x 6.ꢀ x 7.2  
2.ꢀ x 6.ꢀ x 7.2  
2.ꢀ x 6.ꢀ x 7.2  
3.ꢀ x 8.0 x 7.2  
3.ꢀ x 8.0 x 7.2  
4.ꢀ x 9.0 x 7.2  
6.0 x 11.0 x 7.2  
6.0 x 11.0 x 7.2  
2.ꢀ x 6.ꢀ x 7.2  
2.ꢀ x 6.ꢀ x 7.2  
2.ꢀ x 6.ꢀ x 7.2  
2.ꢀ x 6.ꢀ x 7.2  
2.ꢀ x 6.ꢀ x 7.2  
2.ꢀ x 6.ꢀ x 7.2  
3.ꢀ x 8.0 x 7.2  
3.ꢀ x 8.0 x 7.2  
4.ꢀ x 9.0 x 7.2  
63  
06  
40  
63  
0.68  
1.0  
0.022  
0.033  
0.047  
0.068  
0.10  
0.1ꢀ  
0.22  
0.33  
100  
01  
0.0033  
0.0047  
0.0068  
0.010  
0.01ꢀ  
0.022  
0.033  
0.047  
0.068  
0.10  
0.0033  
0.0047  
0.0068  
0.010  
0.01ꢀ  
0.022  
0.033  
0.047  
0.068  
0.10  
0.0010  
0.001ꢀ  
0.0022  
0.0033  
0.0047  
0.0068  
0.010  
0.01ꢀ  
0.022  
2ꢀ0  
2ꢀ  
160  
2ꢀ0  
2ꢀ  
160  
400  
40  
200  
RECOMMENDED PACKAGING  
PACKAGING  
TYPE OF  
HEIGHT (H)  
(mm)  
REEL DIAMETER  
ORDERING CODE  
EXAMPLES  
MKT18172332ꢀꢀG  
MKT18172332ꢀꢀW  
MKT18172332ꢀꢀ  
PITCH  
5
CODE  
PACKAGING  
(mm)  
S (1)  
3ꢀ0  
-
G
W
-
Ammo  
Reel  
Bulk  
18.ꢀ  
18.ꢀ  
-
x
x
x
Note  
(1)  
S = box size ꢀꢀ mm x 210 mm x 340 mm (w x h x l)  
Revision: 11-Jan-18  
Document Number: 26032  
3
For technical questions, contact: dc-film@vishay.com  
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT  
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000  
Not for New Designs - Alternative Device: MKT370  
MKT1817  
Vishay Roederstein  
www.vishay.com  
MOUNTING  
Normal Use  
The capacitors are designed for mounting on printed-circuit boards. The capacitors packed in bandoliers are designed for  
mounting in printed-circuit boards by means of automatic insertion machines.  
For detailed tape specifications refer to packaging information www.vishay.com/docs?28139  
Specific Method of Mounting to Withstand Vibration and Shock  
In order to withstand vibration and shock tests, it must be ensured that the stand-off pips are in good contact with the  
printed-circuit board.  
• For pitches 1ꢀ mm the capacitors shall be mechanically fixed by the leads  
• For larger pitches the capacitors shall be mounted in the same way and the body clamped  
Space Requirements on Printed-Circuit Board  
The maximum space for length (Imax.), width (wmax.) and height (hmax.) of film capacitors to take in account on the printed-circuit  
board is shown in the drawings.  
• For products with pitch 1ꢀ mm, w = l = 0.3 mm; h = 0.1 mm  
Eccentricity defined as in drawing. The maximum eccentricity is smaller than or equal to the lead diameter of the product  
concerned.  
wmax. = w + Δw  
Eccentricity  
CBA116  
I
max. = I + ΔI  
hmax. = h + Δh  
Seating plane  
SOLDERING CONDITIONS  
For general soldering conditions and wave soldering profile, we refer to the document “Characteristics and Definitions Used for  
Film Capacitors”: www.vishay.com/doc?28147  
Storage Temperature  
Tstg = -2ꢀ °C to +3ꢀ °C with RH maximum 7ꢀ % without condensation  
Ratings and Characteristics Reference Conditions  
Unless otherwise specified, all electrical values apply to an ambient free air temperature of 23 °C 1 °C, an atmospheric  
pressure of 86 kPa to 106 kPa and a relative humidity of ꢀ0 % 2 %.  
For reference testing, a conditioning period shall be applied over 96 h 4 h by heating the products in a circulating air oven at  
the rated temperature and a relative humidity not exceeding 20 %.  
Revision: 11-Jan-18  
Document Number: 26032  
4
For technical questions, contact: dc-film@vishay.com  
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT  
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000  
Not for New Designs - Alternative Device: MKT370  
MKT1817  
Vishay Roederstein  
www.vishay.com  
CHARACTERISTICS  
6
6
1 kHz  
1 kHz  
b. 100 V series  
c. 2ꢀ0 V series  
d. 400 V series  
4
4
2
a. 63 V series  
d
c
2
0
max.  
max.  
0
typical  
typical  
b
-2  
-4  
- 2  
- 4  
- 6  
a
min.  
min.  
- 20  
-6  
- 60  
20  
60 Tamb (°C) 100  
-60  
-20  
20  
60  
100  
Tamb (°C)  
Capacitance as a function of ambient temperature  
(typical) for voltage 63 V  
Capacitance as a function of ambient temperature  
(typical) for voltages > 63 V  
2
102  
1
63  
101  
100  
250  
V
;
100 nF  
63  
V
;
10 nF  
V
;
1 µF  
0
- 1  
10- 1  
10- 2  
10- 3  
- 2  
- 3  
105  
105  
106  
107  
108  
102  
103  
104  
104  
f (Hz)  
f (Hz)  
Capacitance as a function of frequency  
(typical curve)  
Impedance as a function of frequency  
102  
102  
ꢀ6 nF  
1000 nF  
101  
101  
ꢀ6 nF  
1000 nF  
Tamb ≤ 8ꢀ °C, 63 VDC  
8ꢀ °C < Tamb ≤ 100 °C, 63 VDC  
100  
100  
101  
102  
103  
104  
f (Hz)  
10ꢀ  
101  
102  
103  
104  
10ꢀ  
f (Hz)  
Max. AC voltage as a function of frequency  
Max. AC voltage as a function of frequency  
Revision: 11-Jan-18  
Document Number: 26032  
5
For technical questions, contact: dc-film@vishay.com  
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT  
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000  
Not for New Designs - Alternative Device: MKT370  
MKT1817  
Vishay Roederstein  
www.vishay.com  
102  
102  
12 nF  
22 nF  
47 nF  
100
101  
101  
330 n
12 nF  
22 nF  
47 nF  
100
330
8ꢀ °C < Tamb ≤ 10ꢀ °C, 100 VDC  
Tamb ≤ 8ꢀ °C, 100 VDC  
100  
101  
100  
102  
103  
104  
10ꢀ  
10ꢀ  
10ꢀ  
101  
102  
103  
104  
10ꢀ  
10ꢀ  
10ꢀ  
f (Hz)  
Max. AC voltage as a function of frequency  
f (Hz)  
Max. AC voltage as a function of frequency  
103  
103  
102  
101  
100  
102  
101  
100  
4.7 nF  
10 nF  
22 nF  
47 nF  
100 nF  
4.7 nF  
10 nF  
22 nF  
47 nF  
100 nF  
Tamb ≤ 8ꢀ °C, 2ꢀ0 VDC  
102  
8ꢀ °C < Tamb ≤ 10ꢀ °C, 2ꢀ0 VDC  
101  
103  
104  
101  
102  
103  
104  
f (Hz)  
f (Hz)  
Max. AC voltage as a function of frequency  
Max. AC voltage as a function of frequency  
103  
103  
102  
101  
100  
102  
101  
100  
2.2
4.7 nF  
10 nF  
2.2
4.7 nF  
10 nF  
Tamb ≤ 8ꢀ °C, 400 VDC  
102  
8ꢀ °C < Tamb ≤ 10ꢀ °C, 400 VDC  
101  
103  
104  
101  
102  
103  
104  
f (Hz)  
f (Hz)  
Max. AC voltage as a function of frequency  
Max. AC voltage as a function of frequency  
Revision: 11-Jan-18  
Document Number: 26032  
6
For technical questions, contact: dc-film@vishay.com  
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT  
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000  
Not for New Designs - Alternative Device: MKT370  
MKT1817  
Vishay Roederstein  
www.vishay.com  
Maximum RMS Current (Sinewave) as a Function of Frequency  
The maximum RMS current is defined by Iac = x C x Uac.  
UAC is the maximum AC voltage depending on the ambient temperature in the curves “Max. RMS voltage and AC current as a  
function of frequency”.  
103  
105  
104  
103  
102  
5
4
3
2
1
102  
C ≤ 0.33 μF (curve 1)  
0.33 μF < C ≤ 1.2 μF (curve 2)  
1.2 μF < C ≤ 3.9 μF (curve 3)  
3.9 μF < C < 6.8 μF (curve 4)  
C ≥ 6.8 μF (curve ꢀ)  
101  
102  
103  
104  
105  
100  
Tamb (°C)  
f (Hz)  
- 50  
0
50  
Tangent of loss angle as a function of frequency  
(typical curve)  
Insulation resistance as a function of the ambient temperature  
(typical curve)  
1.2  
1.2  
1.0  
0.8  
0.6  
0.4  
0.2  
0.0  
1.0  
0.8  
0.6  
0.4  
0.2  
0.0  
- 60  
- 20  
20  
60  
100  
Tamb (°C)  
- 60  
- 20  
20  
60 Tamb (°C) 100  
Max. DC and AC voltage as a function of temperature  
for voltage 63 V  
Max. DC and AC voltage as a function of temperature  
for voltages > 63 V  
16  
12  
8
16  
12  
8
4
0
4
0
- 60  
- 20  
20  
60  
100  
- 60  
- 20  
20  
60  
100  
Tamb (°C)  
T
amb (°C)  
Maximum allowed component temperature rise (T)  
Maximum allowed component temperature rise (T)  
as a function of the ambient temperature Tamb for voltage 63 V  
Revision: 11-Jan-18  
as a function of the ambient temperature Tamb for voltages > 63 V  
Document Number: 26032  
7
For technical questions, contact: dc-film@vishay.com  
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT  
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000  
Not for New Designs - Alternative Device: MKT370  
MKT1817  
Vishay Roederstein  
www.vishay.com  
HEAT CONDUCTIVITY (G) AS A FUNCTION OF (ORIGINAL) PITCH AND CAPACITOR BODY  
THICKNESS IN mW/°C  
HEAT CONDUCTIVITY (mW/°C)  
Wmax.  
(mm)  
PITCH 5 mm  
2.ꢀ  
3.0  
4.ꢀ  
6.0  
2.ꢀ  
3.0  
4.0  
ꢀ.ꢀ  
POWER DISSIPATION AND MAXIMUM COMPONENT TEMPERATURE RISE  
The power dissipation must be limited in order not to exceed the maximum allowed component temperature rise as a function  
of the free ambient temperature.  
The power dissipation can be calculated according type detail specification “HQN-384-01/101: Technical Information Film  
Capacitors”.  
The component temperature rise (T) can be measured (see section “Measuring the Component Temperature” for more details)  
or calculated by T = P/G:  
• T = component temperature rise (°C)  
• P = power dissipation of the component (mW)  
• G = heat conductivity of the component (mW/°C)  
MEASURING THE COMPONENT TEMPERATURE  
A thermocouple must be attached to the capacitor body as in:  
Thermocouple  
The temperature is measured in unloaded (Tamb) and maximum loaded condition (TC).  
The temperature rise is given by T = TC - Tamb.  
To avoid radiation or convection, the capacitor should be tested in a wind-free box.  
Revision: 11-Jan-18  
Document Number: 26032  
8
For technical questions, contact: dc-film@vishay.com  
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT  
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000  
Not for New Designs - Alternative Device: MKT370  
MKT1817  
Vishay Roederstein  
www.vishay.com  
APPLICATION NOTE AND LIMITING CONDITIONS  
These capacitors are not suitable for mains applications as across-the-line capacitors without additional protection, as  
described hereunder. These mains applications are strictly regulated in safety standards and therefore electromagnetic  
interference suppression capacitors conforming the standards must be used.  
For capacitors connected in parallel, normally the proof voltage and possibly the rated voltage must be reduced. For information  
depending of the capacitance value and the number of parallel connections contact: dc-film@vishay.com  
To select the capacitor for a certain application, the following conditions must be checked:  
1. The peak voltage (UP) shall not be greater than the rated DC voltage (URDC  
)
2. The peak-to-peak voltage (UP-P) shall not be greater than 22 x URAC to avoid the ionization inception level  
3. The voltage peak slope (dU/dt) shall not exceed the rated voltage pulse slope in an RC-circuit at rated voltage and without  
ringing. If the pulse voltage is lower than the rated DC voltage, the rated voltage pulse slope may be multiplied by URDC and  
divided by the applied voltage.  
For all other pulses following equation must be fulfilled:  
T
2
dU  
dt  
dU  
2 x   
------- x dt URDC x -------  
dt  
rated  
0
T is the pulse duration.  
4. The maximum component surface temperature rise must be lower than the limits (see graph “Max. allowed component  
temperature rise”).  
ꢀ. Since in circuits used at voltages over 280 V peak-to-peak the risk for an intrinsically active flammability after a capacitor  
breakdown (short circuit) increases, it is recommended that the power to the component is limited to 100 times the values  
mentioned in the table: “Heat Conductivity”  
6. When using these capacitors as across-the-line capacitor in the input filter for mains applications or as series connected  
with an impedance to the mains the applicant must guarantee that the following conditions are fulfilled in any case (spikes  
and surge voltages from the mains included).  
VOLTAGE CONDITIONS FOR 6 ABOVE  
85 °C < Tamb 100 °C FOR 63 V  
ALLOWED VOLTAGES  
Tamb 85 °C  
85 °C < Tamb 100 °C FOR > 63 V  
See “Max. AC voltage as function  
of temperature” per characteristics  
Maximum continuous RMS voltage  
URAC  
Maximum temperature RMS-overvoltage (< 24 h)  
Maximum peak voltage (VO-P) (< 2 s)  
1.2ꢀ x URAC  
1.6 x URDC  
URAC  
1.3 x URDC  
Example  
C = 330 nF - 63 V used for the voltage signal shown in next drawing.  
U
P-P = 40 V; UP = 3ꢀ V; T1 = 100 μs; T2 = 200 μs  
The ambient temperature is 3ꢀ °C  
Checking conditions:  
1. The peak voltage UP = 3ꢀ V is lower than 63 VDC  
2. The peak-to-peak voltage 40 V is lower than 22 x 40 VAC = 113 UP-P  
3. The voltage pulse slope (dU/dt) = 40 V/100 μs = 0.4 V/μs  
This is lower than 60 V/μs (see specific reference data for each version)  
4. The dissipated power is 16.2 mW as calculated with fourier terms  
The temperature rise for wmax. = 3.ꢀ mm and pitch = ꢀ mm will be 16.2 mW/3.0 mW/°C = ꢀ.4 °C  
This is lower than 1ꢀ °C temperature rise at 3ꢀ °C, according figure “Max. allowed component temperature rise”  
ꢀ. Not applicable  
6. Not applicable  
Voltage Signal  
Voltage  
UP  
UP-P  
Time  
T1  
T2  
Revision: 11-Jan-18  
Document Number: 26032  
9
For technical questions, contact: dc-film@vishay.com  
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT  
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000  
Not for New Designs - Alternative Device: MKT370  
MKT1817  
Vishay Roederstein  
www.vishay.com  
INSPECTION REQUIREMENTS  
General Notes  
Sub-clause numbers of tests and performance requirements refer to the “Sectional Specification, Publication IEC 60384-2 and  
Specific Reference Data”.  
GROUP C INSPECTION REQUIREMENTS  
SUB-CLAUSE NUMBER AND TEST  
CONDITIONS  
PERFORMANCE REQUIREMENTS  
SUB-GROUP C1A PART OF SAMPLE   
OF SUB-GROUP C1  
4.1 Dimensions (detail)  
As specified in chapters “MKT370 General  
Data” of this specification  
4.3.1 Initial measurements  
Capacitance  
Tangent of loss angle:  
for C 470 nF at 100 kHz  
for C > 470 nF at 10 kHz  
4.3 Robustness of terminations  
4.4 Resistance to soldering heat  
Tensile and bending  
No visible damage  
Method: 1A  
Solder bath: 280 °C ꢀ °C  
Duration: 10 s  
4.14 Component solvent resistance  
4.4.2 Final measurements  
Isopropylalcohol at room temperature  
Method: 2  
Immersion time: ꢀ min 0.ꢀ min  
Recovery time: min. 1 h, max. 2 h  
Visual examination  
No visible damage  
Legible marking  
Capacitance  
|C/C| 2 % of the value measured initially  
Tangent of loss angle  
Increase of tan :  
0.00ꢀ for: C 100 nF or  
0.010 for: 100 nF < C 220 nF or  
0.01ꢀ for: 220 nF < C 470 nF or  
0.003 for: C > 470 nF  
Compared to values measured in 4.3.1  
SUB-GROUP C1B OTHER PART OF  
SAMPLE OF SUB-GROUP C1  
4.6.1 Initial measurements  
4.6 Rapid change of temperature  
4.7 Vibration  
Capacitance  
Tangent of loss angle:  
for C 470 nF at 100 kHz  
for C > 470 nF at 10 kHz  
A = -ꢀꢀ °C  
B = +100 °C  
ꢀ cycles  
Duration t = 30 min  
Visual examination  
No visible damage  
Mounting:   
see section “Mounting” of this specification  
Procedure B4  
Frequency range: 10 Hz to ꢀꢀ Hz  
Amplitude: 0.7ꢀ mm or  
Acceleration 98 m/sꢁ  
(whichever is less severe)  
Total duration 6 h  
Revision: 11-Jan-18  
Document Number: 26032  
10  
For technical questions, contact: dc-film@vishay.com  
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT  
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000  
Not for New Designs - Alternative Device: MKT370  
MKT1817  
Vishay Roederstein  
www.vishay.com  
GROUP C INSPECTION REQUIREMENTS  
SUB-CLAUSE NUMBER AND TEST  
CONDITIONS  
PERFORMANCE REQUIREMENTS  
SUB-GROUP C1B OTHER PART OF  
SAMPLE OF SUB-GROUP C1  
4.7.2  
Final inspection  
Visual examination  
No visible damage  
4.9  
Shock  
Mounting:   
see section “Mounting” of this specification  
Pulse shape: half sine  
Acceleration: 490 m/sꢁ  
Duration of pulse: 11 ms  
4.9.3  
Final measurements  
Visual examination  
Capacitance  
No visible damage  
|C/C| 3 % of the value measured in 4.6.1  
Tangent of loss angle  
Increase of tan :  
0.010 for: C 220 nF or  
0.01ꢀ for: 220 nF < C 470 nF or  
0.003 for: C > 470 nF  
Compared to values measured in 4.6.1  
Insulation resistance  
As specified in section “Specific Reference  
Data 370” of this specification  
SUB-GROUP C1 COMBINED SAMPLE   
OF SPECIMENS OF SUB-GROUPS   
C1A AND C1B  
4.10  
Climatic sequence  
4.10.2 Dry heat  
Temperature:   
+100 °C for rated voltage 63 V  
+10ꢀ °C for rated voltage > 63 V  
Duration: 16 h  
4.10.3 Damp heat cyclic  
Test Db, first cycle  
4.10.4 Cold  
Temperature: -ꢀꢀ °C  
Duration: 2 h  
4.10.6 Damp heat cyclic  
Voltage proof = URDC for 1 min within 1ꢀ min  
No breakdown or flash-over  
after removal from testchamber  
Test Db, remaining cycles  
4.10.6.2 Final measurements  
Visual examination  
Capacitance  
No visible damage  
Legible marking  
|C/C| 3 % of the value measured in   
4.4.2 or 4.9.3  
Tangent of loss angle  
Increase of tan :  
0.010 for: C 220 nF or  
0.01ꢀ for: 220 nF < C 470 nF or  
0.00ꢀ for: C > 470 nF  
Compared to values measured in 4.3.1  
or 4.6.1  
Insulation resistance  
ꢀ0 % of values specified in section  
“Specific Reference Data 370” of this  
specification  
Revision: 11-Jan-18  
Document Number: 26032  
11  
For technical questions, contact: dc-film@vishay.com  
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT  
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000  
Not for New Designs - Alternative Device: MKT370  
MKT1817  
Vishay Roederstein  
www.vishay.com  
GROUP C INSPECTION REQUIREMENTS  
SUB-CLAUSE NUMBER AND TEST  
SUB-GROUP C2  
CONDITIONS  
PERFORMANCE REQUIREMENTS  
4.11 Damp heat steady state  
ꢀ6 days, 40 °C, 90 % to 9ꢀ % RH  
4.11.1 Initial measurements  
Capacitance  
Tangent of loss angle at 1 kHz  
4.11.3 Final measurements  
Voltage proof = URDC for 1 min within 1ꢀ min  
No breakdown or flash-over  
after removal from testchamber  
Visual examination  
No visible damage  
Legible marking  
Capacitance  
|C/C| ꢀ % of the value measured in 4.11.1.  
Tangent of loss angle  
Increase of tan : 0.00ꢀ  
Compared to values measured in 4.11.1  
Insulation resistance  
ꢀ0 % of values specified in section  
“Specific Reference Data 370” of this  
specification  
SUB GROUP C3  
4.12 Endurance  
Duration: 2000 h  
1.2ꢀ x URDC at 8ꢀ °C  
0.8 x 1.2ꢀ URDC at 100 °C  
for rated voltage 63 V  
0.8 x 1.2ꢀ URDC at 10ꢀ °C  
for rated voltage > 63 V  
4.12.1 Initial measurements  
4.12.ꢀ Final measurements  
Capacitance  
Tangent of loss angle:  
for C 470 nF at 100 kHz  
for C > 470 nF at 10 kHz  
Visual examination  
Capacitance  
No visible damage  
Legible marking  
|C/C| ꢀ % compared to values measured  
in 4.12.1  
Tangent of loss angle  
Increase of tan :  
0.00ꢀ at 8ꢀ °C  
0.010 at 100 °C for: C 220 nF or  
0.01ꢀ for: 220 nF < C 470 nF or  
0.003 for: C > 470 nF  
Compared to values measured in 4.12.1  
Insulation resistance  
ꢀ0 % of values specified in section  
“Specific Reference Data 370” of this  
specification  
Revision: 11-Jan-18  
Document Number: 26032  
12  
For technical questions, contact: dc-film@vishay.com  
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT  
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000  
Not for New Designs - Alternative Device: MKT370  
MKT1817  
Vishay Roederstein  
www.vishay.com  
GROUP C INSPECTION REQUIREMENTS  
SUB-CLAUSE NUMBER AND TEST  
SUB-GROUP C4  
CONDITIONS  
PERFORMANCE REQUIREMENTS  
4.13 Charge and discharge  
10 000 cycles  
Charged to URDC  
Discharge resistance:  
UR  
R = ---------------------------------------------------  
C x 2.ꢀ x dU/dtR  
4.13.1 Initial measurements  
4.13.3 Final measurements  
Capacitance  
Tangent of loss angle:  
for C 470 nF at 100 kHz  
for C > 470 nF at 10 kHz  
Capacitance  
|C/C| 3 % compared to values measured  
in 4.13.1  
Tangent of loss angle  
Increase of tan :  
0.00ꢀ for: C 100 nF or  
0.010 for: 100 nF < C 220 nF or  
0.01ꢀ for: 220 nF < C 470 nF or  
0.003 for: C > 470 nF  
Compared to values measured in 4.13.1  
Insulation resistance  
ꢀ0 % of values specified in section  
“Specific Reference Data 370” of this  
specification  
Revision: 11-Jan-18  
Document Number: 26032  
13  
For technical questions, contact: dc-film@vishay.com  
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT  
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000  
Legal Disclaimer Notice  
www.vishay.com  
Vishay  
Disclaimer  
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE  
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.  
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,  
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other  
disclosure relating to any product.  
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or  
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all  
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,  
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular  
purpose, non-infringement and merchantability.  
Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical  
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements  
about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product  
with the properties described in the product specification is suitable for use in a particular application. Parameters provided in  
datasheets and / or specifications may vary in different applications and performance may vary over time. All operating  
parameters, including typical parameters, must be validated for each customer application by the customer's technical experts.  
Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited  
to the warranty expressed therein.  
Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and  
for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of  
any of the products, services or opinions of the corporation, organization or individual associated with the third-party website.  
Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website  
or for that of subsequent links.  
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining  
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.  
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please  
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.  
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by  
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.  
© 2021 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED  
Revision: 09-Jul-2021  
Document Number: 91000  
1

相关型号：

SI9130DB

 5- and 3.3-V Step-Down Synchronous Converters

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135LG-T1

 SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135LG-T1-E3

 SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135_11

 SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9136_11

 Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130CG-T1-E3

 Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130LG-T1-E3

 Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130_11

 Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137

 Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137DB

 Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137LG

 Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9122E

 500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification Drivers

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明