SI9113DY-E3 [VISHAY]
HIGH-VOLTAGE CURRENT MODE PWM CONTR-LEAD - Tape and Reel;
| 型号： | SI9113DY-E3 |
| 厂家： | 
VISHAY |
| 描述： | HIGH-VOLTAGE CURRENT MODE PWM CONTR-LEAD - Tape and Reel CD 开关 光电二极管 |
| 文件： | 总12页 (文件大小：150K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
End of Life. Last Available Purchase Date is 31-Dec-2014
Si9113
Vishay Siliconix
High-Voltage Current Mode PWM Controller for
ISDN Power Supplies
FEATURES
BiC/DMOS Technology
Current Mode Control
Max 50% Duty Cycle Operation
1.3-MHz Error Amp
Up to 500-kHz Internal Oscillator
Soft-Start
Internal Start-Up Circuit
Power_Good Output
0.6-V Fast Over-Current Protection
<5- A Supply Current for +VIN <18 V
23.5-V to 200-V Input Voltage Range
Programmable Start/Stop Capability
DESCRIPTION
Si9113 is a current mode PWM controller for ISDN power
supplies. In a 14-pin SOIC package, it provides all necessary
functions to implement a single-switch PWM with a minimum
of external parts. To maximize the circuit integration, the
Si9113 is designed with a 200-V depletion mode MOSFET
capable of powering directly off the high input bus without an
external start-up circuit. The Start and Stop input voltage
thresholds can be programmed within the operating input
voltage range by means of a resistor divider, provided +VIN
(Start) > +VIN (Stop). The internal clock frequency is set with
a single external resistor and is capable of capacitor-coupled
external synchronization. In order to satisfy the stringent
ambient temperature requirements, the Si9113 is rated to
handle the industrial range of −40 C to 85 C.
The Si9113 is available in both standard and lead (Pb)-free
packages.
FUNCTIONAL BLOCK DIAGRAM
V
IN
(23.5 V to 200 V)
V
OUT
Start-Up
Drive
Current
Stop/Start
Comparator
Power_Good
V
REF
= 1.3 V
Fast
Current
Limit
Comparator
See Detailed Block Diagram, page 7
.
Applications information see AN728.
A Demonstration Borad data sheet is available for this product.
Document Number: 71093
S-40746—Rev. B. 19-Apr-04
www.vishay.com
1
Si9113
Vishay Siliconix
ABSOLUTE MAXIMUM RATINGS
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220 V
V
IN
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150_C
a
Power Dissipation (Package)
V
CC
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V
b
14-Pin SOIC (Y Suffix) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 900 mW
Logic Inputs (OSC IN, OSC OUT, PWR_GOOD) . . . −0.3 V to V + 0.3 V
CC
Thermal Impedance (Q
)
or "10 mA
JA
14-Pin SOIC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140_C/W
Linear Inputs (FB, V
, SENSE, SS) . . . . . . . . . . . . −0.3 V to V + 0.3 V
CC
REF
Notes
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65 to 150_C
Operating Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −40 to 85_C
a. Device mounted with all leads soldered or welded to PC board.
b. Derate 7.2 mW/_C above 25_C.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation
of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
RECOMMENDED OPERATING RANGE
V
V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23.5 V to 200 V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 V to 14 V
Linear Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 V to V − 3 V
CC
IN
F
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 kHz to 500 kHz
CC
OSC
Digital Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 V to V
CC
a
SPECIFICATIONS
Limits
Test Conditions
Unless Otherwise Specified
−40 to 85_C
Typd
Parameter
Reference
Symbol
Tempb Minc
Maxc
Unit
V
CC
= 10 V, +V = 48 V, R
= 390 kW
OSC
IN
OSC = − V (OSC Disabled)
Room
Full
1.275
1.26
1.3
1.3
1.325
1.34
IN
IN
Output Voltage
V
REF
V
R
= 10 MW
L
Short Circuit Current
Load Regulation
Line Regulation
I
V
= −V
IN
Room
Full
−25
"10
"2
−10
40
5
mA
SREF
REF
I
= 0 to −0.5 mA
REF
DV
mV
REF
V
= 10 to 14 V
Full
CC
UVLO
V
Turn-On
Turn-Off
Full
8.10
8.10
8.8
8.8
9.50
9.50
0.05
0.05
9.5
UVSTART
Under Voltage Lockout
V
V
Full
UVSTOP
I
Room
Room
Room
Room
Room
START
Input Bias Current
V
STOP
= 8 V, V
= 8 V
mA
START
I
STOP
Pre-Regulated V
V
REG
8.5
7.9
0.3
9.0
8.4
0.6
CC
UVLO for V
CC
V
CCUV
8.9
V
V
REG
− V
VD
CCUV
PWR_Good Comparator
Rise Time
t
Room
Room
Room
35
25
mS
mS
V
rpg
C
= 100 nF
PWR_Good
Fall Time
t
fpg
Output Logic Low
I
= 2.5 mA
0.4
0.8
SINK
Soft-Start
SS Current
I
Room
Room
11
mA
SS
Output Inhibit Voltage
V
3.3
V
SS
Oscillator
e
Maximum Frequency
f
R
= 0
Room
Room
Room
Room
Full
500
80
MAX
OSC
R
R
= 390 k (Note f)
= 180 k (Note f)
100
200
10
120
240
15
kHz
OSC
Initial Accuracy
Voltage Stability
f
OSC
160
OSC
Df/f
Df/f = (f [14 V] − f [10 V]) / f [10 V]
%
ppm/_C
%
e
Temperature Coefficient
T
450
50
650
OSC
Maximum Duty Cycle
D
MAX
f
= 100 kHz
Room
OSC
Document Number: 71093
S-40746—Rev. B. 19-Apr-04
www.vishay.com
2
Si9113
Vishay Siliconix
a
SPECIFICATIONS
Limits
Test Conditions
Unless Otherwise Specified
−40 to 85_C
Typd
Parameter
Symbol
Tempb Minc
Maxc
Unit
V
CC
= 10 V, +V = 48 V, R
= 390 kW
IN
OSC
Error Amplifier
e
Open Loop Voltage Gain
A
OSC IN = − V
Room
Room
Full
50
−1
60
dB
mA
VOL
IN
Input BIAS Current
I
V
FB
= 1.3 V
1
1.32
2
BIAS
Feedback Input Voltage
V
FB Tied to COMP, OSC IN = − V
1.28
V
FB
IN
e
Dynamic Output Impedance
Z
Room
Room
Room
Room
Room
1
kW
MHz
OUT
e
Unity Gain Bandwidth
BW
1
1.3
−5
Source V = 0.8 V
−1
FB
Output Current
I
mA
dB
OUT
Sink V = 1.8 V
0.12
50
0.15
70
FB
e
Power Supply Rejection
PSRR
Current Limit Comparator
Threshold Voltage
V
V
= 0 V
Full
Full
0.5
0.6
0.7
V
SOURCE
FB
e
Delay to Output
t
d
V
= 0.85 V, See Figure 1
100
150
ns
SENSE
Output Drive
Room
Full
9.7
9.5
Output High Voltage
V
I
= −10 mA
OH
OUT
V
Room
Full
0.3
0.5
Output Low Voltage
V
I
= 10 mA
OL
OUT
Rise Time
Fall Time
t
Room
Room
40
40
75
75
r
C
= 500 pF
L
ns
(10% to 90%)
t
f
Supply
V
CC
V
= 10 V, R
= 390 kW
OSC
I
Full
1
1.4
mA
CC
vV v 200 V
UVUP
IN
Supply Current
Excluding I From Resistive Divider of
Stop and Start Pins
I
I
Room
Room
75
2
100
5
VIN
mA
Supply Current UVLO Mode
Notes
+V v 18 V, V
(Pin 14) < 8.8 V
VIN
IN
START
a. Refer to PROCESS OPTION FLOWCHART for additional information.
b. Room = 25_C, Full = −40 to 85_C.
c. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum.
d. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing.
e. Guaranteed by design, not subject to production test.
f.
C
STRAY
Pin 8 = v 5 pF.
TIMING WAVEFORMS
0.85 V −
50%
SENSE
t v 10 ns
r
0
t
d
V
CC
90%
OUTPUT
0 −
FIGURE 1. Delay Time for Current Sense
Document Number: 71093
S-40746—Rev. B. 19-Apr-04
www.vishay.com
3
Si9113
Vishay Siliconix
TYPICAL CHARACTERISTICS (25_C UNLESS NOTED)
V
vs. Temperature (V = 48 V)
V
/V
vs. Temperature
REF
IN
UVSTART UVSTOP
1.306
1.304
1.302
1.300
1.298
9.1
9.0
8.9
8.8
8.7
8.6
8.5
8.4
V
CC
= 14 V
V
CC
= 12 V
V
= 10 V
CC
−50
−25
0
25
50
75
100
−50
−25
0
25
50
75
100
Temperature (_C)
Temperature (_C)
Output Frequency vs. Oscillator Resistance
Supply Current vs. Output Frequency
2.0
1.6
1.2
0.8
0.4
0.0
300
100
V
CC
= 10 V
V
CC
= 14 V
V
CC
= 10 V
V
CC
= 12 V
10
0
50
100
150
(kHz)
200
250
300
10
100
1000 2000
F
(kW)
F
OUT
OSC
Output Frequency vs. Supply Voltage
Soft-Start Current vs. Temperature
24
22
20
18
16
14
13
12
11
10
9
R
OSC
= 1 MW
V
CC
= 10 V
85_C
25_C
−40_C
8
7
9
10
11
12
(V)
13
14
15
−40
−20
0
20
40
60
80
100
V
Temperature (_C)
CC
Document Number: 71093
S-40746—Rev. B. 19-Apr-04
www.vishay.com
4
Si9113
Vishay Siliconix
TYPICAL CHARACTERISTICS (25_C UNLESS NOTED)
UVLO Supply Current vs. V
Output Rise Time vs. Load
IN
80
60
40
20
0
10
V
CC
= 10 V
85_C
1
25_C
−40_C
0.1
11
13
15
17
19
21
0
200
400
OUT
600
800
V
IN
(V)
C
(pF)
Efficiency vs. Output Power
90
80
70
60
50
40
30
20
10
V
IN
= 28 V
V
IN
= 48 V
V
IN
= 99 V
0
200
400
600
(mW)
800
1000
W
O
Document Number: 71093
S-40746—Rev. B. 19-Apr-04
www.vishay.com
5
Si9113
Vishay Siliconix
PIN CONFIGURATION
SOIC-14
STOP
START
COMP
FB
1
2
3
4
5
6
7
14
13
12
11
10
9
ORDERING INFORMATION
V
IN
Part Number
Temperature Range
Package
SENSE
Si9113
PWR_GOOD
V
REF
Si9113DY
Bulk
−V
IN
SS
Si9113DY-T1
Si9113DY-T1—E3
−40 to 85_C
Tape and Reel
DRIVER
OSC
OUT
V
CC
OSC
IN
8
Eval Kit
Temperature Range
Board Type
Top View
Si9113D1
Si9113D2
Surface Mount and
Thru-Hole
−10 to 70_C
PIN DESCRIPTION
Pin Number
Name
Function
1
2
STOP
+V
Set up the stop threshold of +V for V via resistive dividers
IN CC
Input voltage to UVLO and Start-Up circuitry
IN
3
SENSE
Current sense amplifier input for current mode control and OCP.
4
PWR_GOOD
Logic high PWR_Good signal indicates FB voltage is within regulation.
Ground pin
5
−V
IN
6
DRIVER
MOSFET gate drive signal.
7
V
CC
Supply voltage to internal circuitry and MOSFET gate drive.
8
OSC
R
OSC
R
OSC
terminal
IN
9
OSC
terminal, square waveform output
OUT
10
11
12
13
14
SS
Soft-Start, time programmed by capacitor value.
1.3-V reference. Decoupled with 0.1-mF capacitor.
Inverting input of an error amplifier.
V
REF
FB
COMP
START
Error amplifier output for external compensation network.
Set up the start threshold of +V for V via resistive dividers
IN
CC
Document Number: 71093
S-40746—Rev. B. 19-Apr-04
www.vishay.com
6
Si9113
Vishay Siliconix
DETAILED BLOCK DIAGRAM
8
OSCIN
13
9
COMP
OSCOUT
V
CC
OSC
Clock ( /
1
4
f
)
2
OSC
PWR_GOOD
FB
Error
Amplifier
3.6 V
PWM
Comparator
12
11
−
−
+
−
R
V
REF
+
+
Q
MOS Driver
6
S
+
DRIVER
Ref
Gen
C/L
Comparator
−
5
−V
IN
10
0.6 V
SS
3
SENSE
7
V
CC
2
1
V
IN
Start-Up
Pre-Regulator
Enable
Programmable
STOP
14
Start/Stop
START
Circuit
DETAILED DESCRIPTION
Start-Up
the internal reference VUVSTOP). The user can program the
+VIN START and +VIN STOP voltage with the external resistor
divider R3−R5 (see Figure 2) as follows:
The Si9113 start-up circuit prevents the internal circuits from
turning on until the voltage on the +VIN pin, via the resistor
divider R3, R4, R5, is sufficiently positive such that the voltage
across R3 (VSTART) is >8.8 V (typical value for the internal
reference VUVSTART [see Figure 2]). When this occurs, the
internal 1.3-V reference, soft-start and oscillator circuits are
enabled. A constant current source provides the current to the
external soft-start capacitor, which allows the output voltage to
rise gradually without overshoot. The output drive circuit is
disabled until the soft-start voltage reaches 3.3 V. The
controller is continuously powered in the state until the VIN
voltage falls and VSTOP drops below 8.8 V (the typical value for
R3 ) R4 ) R5
(1)
+ ǒ
Ǔ
VIN(START)
VUVSTART
R5
R3 ) R5
(2)
+ ǒ Ǔ
VIN(STOP)
VUVSTOP
R5
Since VUVSTART = VUVSTOP = 8.8 V (typical) the hysteresis
voltage can be expressed as:
Document Number: 71093
S-40746—Rev. B. 19-Apr-04
www.vishay.com
7
Si9113
Vishay Siliconix
period eliminating any chance of undesirable noise frequency.
When the output load current decreases to 0 A, the controller
is forced to enter the pulse skipping mode. This is a natural
phenomenal for all controllers since the duty cycle cannot
decrease linearly to 0%.
R4
R5
(3)
+ ǒ Ǔ
DVIN
VUVSTART
VCC Circuit
The depletion MOSFET process allows the Si9113 controller
to power directly from the high input bus voltage. Once
VUVSTART is met, the pre-regulator start-up circuit generates
the 9.0-V VCC voltage. The VCC voltage is used internally to
power the IC as well as providing the drive current for the
external MOSFET. An internal VCC circuit is disabled once a
higher external voltage (X10 V) is applied to this pin. If VCC is
below VCCUV, the Si9113 will inhibit the driver output switching.
Error Amplifier
The error amplifier gain-bandwidth product and slew rate are
critical parameters which determine the transient response of
converter. The transient response is the function of both small
and large signal responses. The small signal response is
determined by the converter closed loop bandwidth and phase
margin while the large signal is determined by the error
amplifier dv/dt and the inductor di/dt slew rate. Besides the
inductance value, the error amplifier determines the converter
response time. In order to minimize the response time, the
Si9113 is designed with 1.3-MHz error amplifier
gain-bandwidth product to generate the widest converter
bandwidth.
REF
The reference voltage of Si9113 is set at 1.3 V. The reference
voltage is internally connected to the non-inverting input of
error amplifier. The reference is decoupled with 0.1-mF
capacitor.
Current Limit
Soft-Start
Over current protection circuit is provided by monitoring the
voltage on the Sense pin. Once the current sense voltage
reaches 0.6V peak, the output drive stage is disabled for the
remainder of the clock cycle.
The soft-start circuit provides a constant 10-mA current to
external capacitor attached to SS pin. A constant soft-start
current forces a gradual increase in duty cycle which in turn
ensures gradual output voltage rise without overshooting. The
soft-start time is programmed by the capacitance value.
Power_Good Comparator
Oscillator
The PWR_Good signal indicates the status of output voltage.
If the output voltage and VCC are within regulation, the
PWR_Good signal generates a logic high output by monitoring
the voltage on COMP and VCC pins. If either one is out of
regulation, a logic low PWR_Good signal is generated. The
capacitor at the PWR_Good pin determines the rise time of the
power good signal, once all the conditions are met for power
good. The PWR_Good signal is an open collector output
capable of sinking 2.5 mA.
The oscillator consists of a ring of CMOS inverters, capacitors,
and a capacitor discharge switch. An external resistor, ROSC
between the OSCIN and OSCOUT pins sets the frequency. The
maximum frequency is obtained when ROSC = 0 W.
frequency divider in the logic section limits the switch duty
cycle to 50% by locking the switching frequency to one-half of
the oscillator frequency.
,
A
PWM Mode
MOSFET Gate Drive
As the load and line voltage vary, the switching frequency
remains constant. The switching frequency is programmed by
the ROSC value as shown by the oscillator curve. In the PWM
mode, a duty cycle pulse is generated for each switching
The DRIVER pin is designed to drive the low-side n-channel
MOSFET. Typically, the driver stage is sized to sink and source
200-mA of peak current when VCC = 12 V.
Document Number: 71093
S-40746—Rev. B. 19-Apr-04
www.vishay.com
8
Si9113
Vishay Siliconix
TYPICAL APPLICATION CIRCUITS
T1
28 − 99 V
XFMR_EPC17
+V
IN
40 V
D2
BR1
1
4
3
1
2
AC
AC
+
+
ESIG
C1
22 mF
160 V
3
1
−
+
C10
D4*
BZX84C43
NS2
2.2 mF
DF02S
−V
IN
50 V
D1
R13
6
3
7
2.7 W
ESIG
COM
2
C4
1 mF
NP
5
NS3
9
3.3 V
D3
B130LB
C10
C12
0.1 mF
8
220 mF
C5
0.1 mF
10 V
R9
20 kW
COM
1
8
7
R1
1, 2, 5, 6
OSC
V
CC
IN
R10
13 kW
9
6
5
3
1 MW
Q01 Si3420DV
OSC
SS
DR
OUT
10
C7
4
GND
0.001 mF
11
12
13
4
3
2
C6
V
REF
PWR_G
ICS
0.1 mF
R11
FB
1 kW
COMP
START
V
IN
C9
220 pF
R7
14
1
R2
C8
STOP
2 W
300 kW 0.01 mF
1
/
2
W
Si9113
R3
C3
100 pF
5.1 MW
R4
1 MW
R5
3.96 MW
*Optional
FIGURE 2. Dual Output Flyback Converter with 2% Regulation for 3.3 V
( As used on Demo Board—DB1)
Document Number: 71093
S-40746—Rev. B. 19-Apr-04
www.vishay.com
9
Si9113
Vishay Siliconix
TYPICAL APPLICATION CIRCUITS
T1
28 − 99 V
+V
IN
XFMR_EPC17
40 V
D2
BR1
4
4
3
1
2
AC
AC
+
+
ESIG
C1
22 mF
160 V
3
1
−
+
C10
D4*
NS2
2.2 mF
BZX84C43
COM
DF02S
−V
IN
50 V
D1
R13
5
2
3
8
2.7 W
ESIG
D3
NP
9
3.3 V
2
R9
C4
1 mF
B130LB
NS3
6
89 kW
+
C11
C12
0.1 mF
NS1
1
220 mF
10 V
R10
COM
1
12.7 kW
8
7
C5
0.1 mF
R1
1, 2, 5, 6
OSC
V
CC
IN
9
6
5
3
1 MW
Q01 Si3420DV
OSC
SS
DR
OUT
10
C7
4
GND
PWR_G
ICS
0.001 mF
11
12
13
4
3
2
C6
V
REF
0.1 mF
R11
FB
1 kW
COMP
START
V
IN
C9
470 pF
R7
14
1
R2
C8
STOP
2 W
300 kW 0.01 mF
1
/
2
W
Si9113
R3
5.1 MW
C3
100 pF
R4
1 MW
R5
3.96 MW
*Optional
FIGURE 3. Dual Output Flyback Converter with Moderately Regulated Outputs
(As used on Demo Board DB-2)
Document Number: 71093
S-40746—Rev. B. 19-Apr-04
www.vishay.com
10
Package Information
Vishay Siliconix
SOIC (NARROW): 14-LEAD (POWER IC ONLY)
MILLIMETERS
INCHES
Min
1.35
0.10
0.38
0.18
8.55
3.8
Max
1.75
0.20
0.51
0.23
8.75
4.00
Min
Max
0.069
0.008
0.020
0.009
0.344
0.157
Dim
A
A1
B
C
D
0.053
0.004
0.015
0.007
0.336
0.149
14
1
13
2
12
3
11
4
10
5
9
6
8
7
E
E
1.27 BSC
0.050 BSC
e
5.80
0.50
0_
6.20
0.93
8_
0.228
0.020
0_
0.244
0.037
8_
H
L
Ø
ECN: S-40080—Rev. A, 02-Feb-04
DWG: 5914
D
H
C
A
ALL LEADS
0.101 mm
Ø
A
1
e
B
L
0.004″
Document Number: 72809
28-Jan-04
www.vishay.com
1
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of
typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding
statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a
particular product with the properties described in the product specification is suitable for use in a particular application.
Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over
time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.
Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for
such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document
or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
Revision: 08-Feb-17
Document Number: 91000
1
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明