TR8M105K016C9500 [VISHAY]
CAPACITOR, TANTALUM, SOLID, POLARIZED, 16 V, 1 uF, SURFACE MOUNT, 0603, CHIP, GREEN;
| 型号： | TR8M105K016C9500 |
| 厂家： | 
VISHAY |
| 描述： | CAPACITOR, TANTALUM, SOLID, POLARIZED, 16 V, 1 uF, SURFACE MOUNT, 0603, CHIP, GREEN 电容器 |
| 文件： | 总10页 (文件大小：136K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
TR8
Vishay Sprague
www.vishay.com
Solid Tantalum Chip Capacitors
®
MICROTAN Low ESR, Leadframeless Molded
FEATURES
• Lead (Pb)-free face-down terminations
• Mounting: Surface mount
• 8 mm tape and reel packaging available per
EIA-481 and reeling per IEC 60286-3
7" [178 mm] standard
• Low ESR
• Material categorization: For definitions of compliance
please see www.vishay.com/doc?99912
PERFORMANCE CHARACTERISTICS
Operating Temperature: - 55 °C to + 85 °C
Capacitance Tolerance: 20 % standard, 10 % available
Voltage Range: 4 VDC to 16 VDC
(to + 125 °C voltage derating)
Capacitance Range: 1 μF to 220 μF
ORDERING INFORMATION
TR8
M
106
M
6R3
C
2000
TYPE
CASE
CODE
CAPACITANCE
CAPACITANCE
TOLERANCE
DC VOLTAGE RATING
AT + 85 °C
TERMINATION
ESR
See Ratings
and Case
Codes table
This is expressed in
picofarads. The first
two digits are the
significant figures. The
third is the number of
zeros to follow.
K = 10 ꢀ
M = 20 ꢀ
This is expressed in volts.
To complete the
three-digit block, zeros
precede the voltage
rating. A decimal point
is indicated by an “R”
(6R3 = 6.3 V).
C = 100 ꢀ tin
7" [178 mm]
reel
A = Gold/7"
[178 mm] reel
Maximum
100 kHz ESR
in (m) (1)
Notes
•
We reserve the right to supply higher voltage ratings and tighter capacitance tolerance capacitors in the same case size.
Voltage substitutions will be marked with the higher voltage rating.
The EIA and CECC standards for low ESR solid tantalum chip capacitors, allow delta ESR of 1.25 times the datasheet limit after mounting.
(1)
DIMENSIONS in inches [millimeters]
Anode Polarity Bar
Cathode Termination
Anode Termination
W
C
H
P1
P2
P1
L
CASE CODE
L
W
H
P1
P2
C
0.063 0.008
[1.60 0.2]
0.033 0.008
[0.85 0.2]
0.031 0.004
[0.80 0.1]
0.020 0.004
[0.50 0.1]
0.024 0.004
[0.60 0.1]
0.024 0.004
[0.60 0.1]
M
0.094 0.004
[2.4 0.1]
0.126 0.008
[3.2 0.2]
0.126 0.008
[3.2 0.2]
0.057 0.004
[1.45 0.1]
0.063 0.008
[1.6 0.2]
0.063 0.008
[1.6 0.2]
0.043 0.004
[1.10 0.1]
0.039 max.
[1.0 max.]
0.063 0.008
[1.6 0.2]
0.020 0.004
[0.50 0.1]
0.031 0.004
[0.80 0.1]
0.031 0.004
[0.80 0.1]
0.057 0.004
[1.40 0.1]
0.035 0.004
[0.90 0.1]
0.047 0.004
[1.20 0.1]
0.047 0.004
[1.20 0.1]
P
Q
A
0.063
[1.60]
0.063
[1.60]
Revision: 25-May-12
Document Number: 40114
1
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TR8
Vishay Sprague
www.vishay.com
RATINGS AND CASE CODES
μF
1.0
2.2
4.7
10
2.5 V
4 V
6.3 V
10 V
16 V
M
25 V
M
M
M
M
M
M
M
M
M
M
R
A
15
22
33
M
M
P
P
47
100
220
P
P/A
P
P/Q
MARKING
M-Case
P-, R-Case
A-, Q-Case
Capacitance
Code
Voltage
Polarity Bar
EIA Capacitance
Code (pF)
Voltage
Code
Code
Polarity Bar
Polarity Bar Voltage Code
GJ
107
J
A
VOLTAGE CODE
CAPACITANCE CODE
V
CODE
CAP, μF
10
CODE
2.5
4.0
6.3
10
16
20
25
e
G
J
n
33
47
s
A
C
D
E
68
w
A
E
J
100
150
220
Revision: 25-May-12
Document Number: 40114
2
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TR8
Vishay Sprague
www.vishay.com
STANDARD RATINGS
MAX. ESR
AT + 25 °C
100 kHz
()
MAX. RIPPLE
100 kHz
IRMS
MAX. DCL
AT + 25 °C (μA) AT + 25 °C (ꢀ)
MAX. DF
CAPACITANCE
(μF)
CASE
CODE
PART NUMBER
(A)
2.5 VDC AT + 85 °C; 1.6 VDC AT + 125 °C
TR8P227M2R5C1500 11.0 30
4 VDC AT + 85 °C; 2.7 VDC AT + 125 °C
220
P
1.50
0.129
33
47
M
M
P
TR8M336M004C1500
TR8M476M004C1500
TR8P107M004C1500
TR8P227(1)004C1000
TR8Q227M004C1200
2.6
3.8
30
40
30
30
80
1.50
1.50
1.50
1.00
1.20
0.129
0.129
0.173
0.212
0.214
100
220
220
4.0
P
17.6
88.0
Q
6.3 VDC AT + 85 °C; 4 VDC AT + 125 °C
10
15
M
M
M
M
P
TR8M106(1)6R3C2000
TR8M156M6R3C3000
TR8M226M6R3C1500
TR8M336M6R3C1500
TR8P107M6R3C1500
TR8A107M6R3C0500
0.6
0.9
2.8
4.2
6.3
6.3
8
2.00
3.00
1.50
1.50
1.50
0.50
0.112
0.091
0.129
0.129
0.173
0.390
20
20
30
30
20
22
33
100
100
A
10 VDC AT + 85 °C; 7 VDC AT + 125 °C
2.2
4.7
10
15
33
47
47
M
M
M
M
P
TR8M225M010C4000
TR8M475M010C3000
TR8M106M010C2000
TR8M156(1)010C3000
TR8P336M010C2500
TR8P476M010C0800
TR8P476M010C1000
0.5
0.5
1.0
1.5
3.3
4.7
4.7
10
6
4.00
3.00
2.00
3.00
2.50
0.80
1.00
0.079
0.079
0.112
0.091
0.134
0.237
0.212
20
30
20
22
22
P
P
16 VDC AT + 85 °C; 10 VDC AT + 125 °C
1.0
2.2
4.7
10
M
M
M
R
TR8M105(1)016C9500
TR8M225M016C4000
TR8M475M016C4000
TR8R106M016C5000
0.5
0.5
0.8
1.6
6
10
8
9.50
4.00
4.00
5.00
0.050
0.079
0.080
0.095
8
25 VDC AT + 85 °C; 17 VDC AT + 125 °C
TR8A106M025C2500 2.5 10
10
A
2.50
0.173
Note
•
Part number definition:
(1) Tolerance: For 10 % tolerance, specify “K”; for 20 % tolerance, change to “M”
Revision: 25-May-12
Document Number: 40114
3
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TR8
Vishay Sprague
www.vishay.com
CAPACITORS PERFORMANCE CHARACTERISTICS
ELECTRICAL PERFORMANCE CHARACTERISTICS
ITEM
PERFORMANCE CHARACTERISTICS
Category Temperature Range
Capacitance Tolerance
Dissipation Factor (at 120 Hz)
ESR (100 kHz)
- 55 °C to + 85 °C (to + 125 °C with voltage derating)
20 %, 10 %, tested via bridge method, at 25 °C, 120 Hz
Limits per Standard Ratings table. Tested via bridge method, at 25 °C, 120 Hz.
Limits per Standard Ratings table. Tested via bridge method, at 25 °C, 100 kHz.
After application of rated voltage applied to capacitors for 5 min using a steady source of power with
1 k resistor in series with the capacitor under test, leakage current at 25 °C is not more than described
in Standard Ratings table. Note that the leakage current varies with temperature and applied voltage.
See graph below for the appropriate adjustment factor.
Leakage Current
Capacitors are capable of withstanding peak voltages in the reverse direction equal to:
10 % of the DC rating at + 25 °C
5 % of the DC rating at + 85 °C
Reverse Voltage
1 % of the DC rating at + 125 °C
Vishay does not recommend intentional or repetitive application of reverse voltage
If capacitors are to be used at temperatures above + 25 °C, the permissible RMS ripple current or
voltage shall be calculated using the derating factors:
1.0 at + 25 °C
0.9 at + 85 °C
0.4 at + 125 °C
Temperature Derating
+ 85 °C RATING
+ 125 °C RATING
RATED VOLTAGE (V)
SURGE VOLTAGE (V)
RATED VOLTAGE (V)
SURGE VOLTAGE (V)
2.5
4.0
6.3
10
16
20
25
35
50
3.3
5.2
8.0
13
20
26
32
46
65
1.7
2.7
4.0
7.0
10
2.2
3.4
5.0
8.0
12
Operating Temperature
13
16
17
20
23
28
33
40
TYPICAL LEAKAGE CURRENT FACTOR RANGE
100
+ 125 °C
+ 85 °C
+ 55 °C
10
1.0
+ 25 °C
0 °C
0.1
- 55 °C
0.01
0.001
0
10
20
30
40
50
60
70
80
90 100
PERCENT OF RATED VOLTAGE
Notes
•
•
•
At + 25 °C, the leakage current shall not exceed the value listed in the Standard Ratings table.
At + 85 °C, the leakage current shall not exceed 10 times the value listed in the Standard Ratings table.
At + 125 °C, the leakage current shall not exceed 12 times the value listed in the Standard Ratings table.
Revision: 25-May-12
Document Number: 40114
4
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TR8
Vishay Sprague
www.vishay.com
ENVIRONMENTAL PERFORMANCE CHARACTERISTICS
ITEM
CONDITION
POST TEST PERFORMANCE
Capacitance change
Dissipation factor
Leakage current
1000 h application of rated voltage at 85 °C
with a 3 series resistance,
MIL-STD-202 method 108A
30 %
Life Test at + 85 °C
Not to exceed 150 % of initial
Not to exceed 200 % of initial
Capacitance change
Dissipation factor
Leakage current
30 %
At 40 °C/90 % RH 500 h, no voltage applied.
MIL-STD-202 method 103B
Humidity Test
Thermal Shock
Not to exceed 150 % of initial
Not to exceed 200 % of initial
Capacitance change
Dissipation factor
Leakage current
30 %
At - 55 °C/+ 125 °C, 30 min each, for 5 cycles.
MIL-STD-202 method 107G
Not to exceed 150 % of initial
Not to exceed 200 % of initial
MECHANICAL PERFORMANCE CHARACTERISTICS
ITEM
CONDITION
POST TEST PERFORMANCE
Apply a pressure load of 5 N for 10 s 1 s
horizontally to the center of capacitor side body.
AEC Q-200 rev. C method 006
There shall be no visual damage when viewed at 20 x
magnification and the component shall meet the original
electrical requirements.
Terminal Strength
Capacitance change
Dissipation factor
Leakage current
ESR
10 %
Initial specified value or less
Initial specified value or less
Initial specified value or less
MIL-STD-202, method 204D,
10 Hz to 2000 Hz, 20 g peak
Vibration
Shock
There shall be no mechanical or visual damage to capacitors
post-conditioning.
Capacitance change
Dissipation factor
Leakage current
ESR
10 %
Initial specified value or less
Initial specified value or less
Initial specified value or less
MIL-STD-202, method 213B, condition I,
100 g peak
There shall be no mechanical or visual damage to capacitors
post-conditioning.
Capacitance change
Dissipation factor
Leakage current
30 %
Not to exceed 150 % of initial
Not to exceed 200 % of initial
Resistance to
Solder Heat
MIL-STD-202, method 210F, condition K
There shall be no mechanical or visual damage to capacitors
post-conditioning.
MIL-STD-202, method 208H, ANSI/J-STD-002,
Test B. Applies only to solder and tin plated
All terminations shall exhibit a continuous solder coating free
from defects for a minimum of 95 % of the critical area of any
Solderability
terminations. Does not apply to gold terminations. individual lead.
Resistance to
Solvents
Marking has to remain legible, no degradation of encapsulation
material.
MIL-STD-202, method 215D
Encapsulation materials meet UL 94 V-0 with an
oxygen index of 32 %
Flammability
Revision: 25-May-12
Document Number: 40114
5
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TR8
Vishay Sprague
www.vishay.com
PLASTIC TAPE AND REEL PACKAGING in inches [millimeters]
0.157 0.004
[4.0 0.10]
10 pitches cumulative
tolerance on tape
0.008 [0.200]
Tape thickness
Deformation
between
embossments
0.059 + 0.004 - 0.0
[1.5 + 0.10 - 0.0]
Embossment
0.014
[0.35]
max.
0.079 0.002
[2.0 0.05]
0.069 0.004
[1.75 0.10]
Top
cover
tape
A0
0.030 [0.75]
min. (3)
20°
F
W
B1 (max.) (6)
K0
Maximum
component
rotation
B0
P1
0.030 [0.75]
min. (4)
Top cover
tape
(Side or front sectional view)
Center lines
of cavity
0.004 [0.10]
max.
For tape feeder
reference only
including draft.
D
1 (min.) for components
(5)
.
0.079 x 0.047 [2.0 x 1.2] and larger
USER DIRECTION
OF FEED
Maximum
(5)
cavity size (1)
Concentric around B0
Cathode (-)
Anode (+)
DIRECTION OF FEED
Tape and Reel Specifications: All case sizes are
available on plastic embossed tape per EIA-481. Tape
reeling per IEC 60286-3 is also available. Standard
reel diameter is 7" [178 mm], 13" [330 mm] reels are
available and recommended as the most cost
effective packaging method.
3.937 [100.0]
0.039 [1.0]
20° maximum
component rotation
max.
Typical
component
cavity
Tape
0.039 [1.0]
max.
B0
center line
The most efficient packaging quantities are full reel
increments on a given reel diameter. The quantities
shown allow for the sealed empty pockets required to
be in conformance with EIA-481. Reel size and
packaging orientation must be specified in the Vishay
Sprague part number.
0.9843 [250.0]
Camber
(Top view)
Typical
component
center line
A0
Allowable camber to be 0.039/3.937 [1/100]
Non-cumulative over 9.843 [250.0]
(Top view)
Notes
•
Metric dimensions will govern. Dimensions in inches are rounded and for reference only.
(1)
A0, B0, K0, are determined by the maximum dimensions to the ends of the terminals extending from the component body and/or the body
dimensions of the component. The clearance between the ends of the terminals or body of the component to the sides and depth of the
cavity (A0, B0, K0) must be within 0.002" (0.05 mm) minimum and 0.020" (0.50 mm) maximum. The clearance allowed must also prevent
rotation of the component within the cavity of not more than 20°.
(2)
(3)
(4)
(5)
(6)
Tape with components shall pass around radius “R” without damage. The minimum trailer length may require additional length to provide
“R” minimum for 12 mm embossed tape for reels with hub diameters approaching N minimum.
This dimension is the flat area from the edge of the sprocket hole to either outward deformation of the carrier tape between the embossed
cavities or to the edge of the cavity whichever is less.
This dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the carrier
tape between the embossed cavity or to the edge of the cavity whichever is less.
The embossed hole location shall be measured from the sprocket hole controlling the location of the embossement. Dimensions of
embossement location shall be applied independent of each other.
B1 dimension is a reference dimension tape feeder clearance only.
CARRIER TAPE DIMENSIONS in inches [millimeters]
CASE
CODE
TAPE
SIZE
B1
(MAX.)
D1
(MIN.)
K0
(MAX.)
F
P1
W
0.108
[2.75]
0.039
[1.0]
0.138 0.002
[3.5 0.05]
0.054
[1.37]
0.157 0.004 0.315 + 0.0118/- 0.0039
P, R
Q, A
8 mm
8 mm
[4.0 1.0]
[8.0 + 0.30/- 0.10]
0.165
[4.2]
0.039
[1.0]
0.138 0.002
[3.5 0.05]
0.094
[2.4]
0.157 0.004
[4.0 1.0]
0.315 0.012
[8.0 0.30]
Revision: 25-May-12
Document Number: 40114
6
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TR8
Vishay Sprague
www.vishay.com
PAPER TAPE AND REEL PACKAGING in inches [millimeters]
[10 pitches cumulative tolerance
P2
on tape 0.2 mm]
T
E1
Ø D0
P0
A0
F
Bottom cover
tape
W
B0
E2
Top
cover tape
Anode
P1
Bottom cover tape
G
Cavity center lines
Cavity size (1)
USER FEED DIRECTION
CASE TAPE
SIZE SIZE
A0
B0
D0
P0
P1 P2
E
F
W
T
0.041 0.002 0.071 0.002 0.06 0.004 0.157 0.004 0.157 0.004 0.079 0.002 0.069 0.004 0.0138 0.002 0.315 0.008 0.037 0.002
[1.05 0.05] [1.8 0.05] [1.5 0.1] [4.0 0.1] [4.0 0.1] [2.0 0.05] [1.75 0.1] [3.5 0.05] [8.0 0.2] [0.95 0.05]
M
8 mm
Note
(1)
A0, B0 are determined by the maximum dimensions to the ends of the terminals extending from the component body and/or the body
dimensions of the component. The clearance between the ends of the terminals or body of the component to the sides and depth of the
cavity (A0, B0) must be within 0.002" (0.05 mm) minimum and 0.020" (0.50 mm) maximum. The clearance allowed must also prevent rotation
of the component within the cavity of not more than 20°.
STANDARD PACKAGING QUANTITY
QUANTITY (PCS/REEL)
CASE CODE
7" REEL
M
R
P
4000
2500
3000
2500
2000
Q
A
RECOMMENDED VOLTAGE DERATING GUIDELINES
STANDARD CONDITIONS. FOR EXAMPLE: OUTPUT FILTERS
Capacitor Voltage Rating
Operating Voltage
4.0
2.5
3.6
6.0
10
12
15
24
28
6.3
10
16
20
25
35
50
SEVERE CONDITIONS. FOR EXAMPLE: INPUT FILTERS
Capacitor Voltage Rating
Operating Voltage
4.0
6.3
10
16
20
25
35
50
2.5
3.3
5.0
8.0
10
12
15
24
Revision: 25-May-12
Document Number: 40114
7
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TR8
Vishay Sprague
www.vishay.com
POWER DISSIPATION
MAXIMUM PERMISSIBLE
POWER DISSIPATION AT + 25 °C (W) IN FREE AIR
CASE CODE
M
R
P
0.025
0.045
0.045
0.055
0.075
Q
A
RECOMMENDED REFLOW PROFILES
Tp °C
(tp)
TL °C
Ts MAX. °C
(tL)
Ts MAX. °C
Preheat (ts)
25 °C
t, s
All Case Codes
TS
TP
TP
TL
TL
TS MIN.
TS MAX.
tS MAX.
tS
TS
tP
MIN.
tL
lead (Pb)-free Sn/Pb
lead (Pb)-free Sn/Pb lead (Pb)-free
lead (Pb)-free Sn/Pb lead (Pb)-free Sn/Pb
Sn/Pb
260 °C
225 °C 10
217 °C
183 °C
150 °C
100 °C
200 °C
150 °C
60 to 150
60 to 90 60
PAD DIMENSIONS in inches [millimeters]
D
C
B
A
A
B
C
D
CASE CODE
(MIN.)
(NOM.)
(NOM.)
(NOM.)
M
R
P
0.039 [1.00]
0.059 [1.50]
0.063 [1.60]
0.071 [1.80]
0.071 [1.80]
0.028 [0.70]
0.031 [0.80]
0.031 [0.80]
0.067 [1.70]
0.067 [1.70]
0.024 [0.60]
0.039 [1.0]
0.047 [1.20]
0.053 [1.35]
0.053 [1.35]
0.080 [2.00]
0.102 [2.60]
0.110 [2.80]
0.187 [4.75]
0.187 [4.75]
Q
A
Revision: 25-May-12
Document Number: 40114
8
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TR8
Vishay Sprague
www.vishay.com
GUIDE TO APPLICATION
1.
AC Ripple Current: The maximum allowable ripple
6.
Printed Circuit Board Materials: Molded capacitors
are compatible with commonly used printed circuit
board materials (alumina substrates, FR4, FR5, G10,
PTFE-fluorocarbon and porcelanized steel).
current shall be determined from the formula:
P
IRMS
=
------------
RESR
7.
Attachment:
7.1
Solder Paste: The recommended thickness of the
where,
P =
solder paste after application is 0.007"
0.001"
Power dissipation in watts at + 25 °C (see
paragraph number 5 and the table Power
Dissipation)
[0.178 mm 0.025 mm]. Care should be exercised in
selecting the solder paste. The metal purity should
be as high as practical. The flux (in the paste) must
be active enough to remove the oxides formed on the
metallization prior to the exposure to soldering heat.
In practice this can be aided by extending the solder
preheat time at temperatures below the liquidous
state of the solder.
Soldering: Capacitors can be attached by
conventional soldering techniques; vapor phase,
convection reflow, infrared reflow, wave soldering
and hot plate methods. The Soldering Profile charts
show recommended time/temperature conditions for
soldering. Preheating is recommended. The
recommended maximum ramp rate is 2 °C per s.
RESR = The capacitor equivalent series resistance at
the specified frequency
2.
AC Ripple Voltage: The maximum allowable ripple
voltage shall be determined from the formula:
P
7.2
VRMS = Z ------------
RESR
or, from the formula:
VRMS = IRMS x Z
where,
P =
Power dissipation in watts at + 25 °C (see
paragraph number 5 and the table Power
Dissipation)
Attachment with
a
soldering iron is not
recommended due to the difficulty of controlling
temperature and time at temperature. The soldering
iron must never come in contact with the capacitor.
RESR = The capacitor equivalent series resistance at
the specified frequency
The capacitor impedance at the specified
frequency
7.2.1 Backward and Forward Compatibility: Capacitors
with SnPb or 100 % tin termination finishes can be
soldered using SnPb or lead (Pb)-free soldering
processes.
Z =
2.1
2.2
The sum of the peak AC voltage plus the applied DC
voltage shall not exceed the DC voltage rating of the
capacitor.
The sum of the negative peak AC voltage plus the
applied DC voltage shall not allow a voltage reversal
exceeding 10 % of the DC working voltage at
+ 25 °C.
Reverse Voltage: These capacitors are capable of
withstanding peak voltages in the reverse direction
equal to 10 % of the DC rating at + 25 °C, 5 % of the
DC rating at + 85 °C and 1 % of the DC rating at
+ 125 °C.
Temperature Derating: If these capacitors are to be
operated at temperatures above + 25 °C, the
permissible RMS ripple current or voltage shall be
calculated using the derating factors as shown:
8.
Cleaning (Flux Removal) After Soldering: Molded
capacitors are compatible with all commonly used
solvents such as TES, TMS, Prelete, Chlorethane,
Terpene and aqueous cleaning media. However,
CFC/ODS products are not used in the production of
these devices and are not recommended. Solvents
containing methylene chloride or other epoxy
solvents should be avoided since these will attack
the epoxy encapsulation material.
When using ultrasonic cleaning, the board may
resonate if the output power is too high. This
vibration can cause cracking or a decrease in the
adherence of the termination. Do not exceed 9W/l at
40 kHz for 2 min.
Recommended Mounting Pad Geometries: Proper
mounting pad geometries are essential for
successful solder connections. These dimensions
are highly process sensitive and should be designed
to minimize component rework due to unacceptable
solder joints. The dimensional configurations shown
are the recommended pad geometries for both wave
and reflow soldering techniques. These dimensions
are intended to be a starting point for circuit board
designers and may be fine tuned if necessary based
upon the peculiarities of the soldering process
and/or circuit board design.
3.
4.
8.1
9.
TEMPERATURE
+ 25 °C
DERATING FACTOR
1.0
0.9
0.4
+ 85 °C
+ 125 °C
5.
Power Dissipation: Power dissipation will be
affected by the heat sinking capability of the
mounting surface. Non-sinusoidal ripple current may
produce heating effects which differ from those
shown. It is important that the equivalent IRMS value
be established when calculating permissible
operating levels. (Power Dissipation calculated using
+ 25 °C temperature rise.)
PRODUCT INFORMATION
Moisture Sensitivity
www.vishay.com/doc?40135
SELECTOR GUIDES
Solid Tantalum Selector Guide
Solid Tantalum Chip Capacitors
FAQ
www.vishay.com/doc?49053
www.vishay.com/doc?40091
Frequently Asked Questions
www.vishay.com/doc?40110
Revision: 25-May-12
Document Number: 40114
9
For technical questions, contact: tantalum@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Revision: 12-Mar-12
Document Number: 91000
1
相关型号：
TR8M105M016C9500
CAPACITOR, TANTALUM, SOLID, POLARIZED, 16 V, 1 uF, SURFACE MOUNT, 0603, CHIP, GREEN
VISHAY
TR8M106K010C2000
CAPACITOR, TANTALUM, SOLID, POLARIZED, 10 V, 10 uF, SURFACE MOUNT, 0603, CHIP, GREEN
VISHAY
TR8M336M6R3C1500
CAPACITOR, TANTALUM, SOLID, POLARIZED, 6.3 V, 33 uF, SURFACE MOUNT, 0603, CHIP, GREEN
VISHAY
©2020 ICPDF网 联系我们和版权申明