TSOP58256SS1SBS21 [VISHAY]
Photo IC;
| 型号： | TSOP58256SS1SBS21 |
| 厂家： | 
VISHAY |
| 描述： | Photo IC |
| 文件： | 总7页 (文件大小：136K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
TSOP582.., TSOP584.., TSOP592.., TSOP594..
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
FEATURES
• Low supply current
• Photo detector and preamplifier in one package
• Internal filter for PCM frequency
• Improved shielding against EMI
• Supply voltage: 2.7 V to 5.5 V
• Improved immunity against ambient light
• Insensitive to supply voltage ripple and noise
19026
• Compliant to RoHS Directive 2002/95/EC and
in accordance to WEEE 2002/96/EC
DESCRIPTION
MECHANICAL DATA
These products are miniaturized receivers for infrared remote
control systems. A PIN diode and a preamplifier are assembled
on a lead frame, the epoxy package acts as an IR filter.
The demodulated output signal can be directly decoded by a
microprocessor. The TSOP582.., TSOP592.. series are
compatible with all common IR remote control data formats.
The TSOP584.., TSOP594, series are optimized to suppress
almost all spurious pulses from energy saving fluorescent
lamps but will also suppress some data signals.
Pinning for TSOP582.., TSOP584..:
1 = OUT, 2 = GND, 3 = VS
Pinning for TSOP592.., TSOP594..:
1 = OUT, 2 = VS, 3 = GND
This component has not been qualified according to
automotive specifications.
PARTS TABLE
STANDARD APPLICATIONS
(AGC2)
VERY NOISY ENVIRONMENTS
(AGC4)
CARRIER
FREQUENCY
PINNING
1 = OUT, 2 = GND, 3 = VS
1 = OUT, 2 = VS, 3 = GND
TSOP59230
1 = OUT, 2 = GND, 3 = VS
TSOP58430
1 = OUT, 2 = VS, 3 = GND
TSOP59430
30 kHz
33 kHz
36 kHz
36.7 kHz
38 kHz
40 kHz
56 kHz
TSOP58230
TSOP58233
TSOP58236
TSOP58237
TSOP58238
TSOP58240
TSOP58256
TSOP59233
TSOP58433
TSOP59433
TSOP59236
TSOP58436
TSOP59436
TSOP59237
TSOP58437
TSOP59437
TSOP59238
TSOP58438
TSOP59438
TSOP59240
TSOP58440
TSOP59440
TSOP59256
TSOP58456
TSOP59456
BLOCK DIAGRAM
APPLICATION CIRCUIT
17170_7
R1
C1
16833_14
Transmitter
with
TSALxxxx
IR receiver
3
1
VS
+ VS
33 kΩ
µC
OUT
GND
VO
GND
Band
pass
Demo-
dulator
Input
AGC
The external components R and C are optional
1
1
to improve the robustness against electrical overstress
(typical values are R = 100 Ω, C = 0.1 µF).
The output voltage VO should not be pulled down to a level
below 1 V by the external circuit.
2
1
1
PIN
Control circuit
The capacitive load at the output should be less than 2 nF.
** Please see document “Vishay Material Category Policy”: www.vishay.com/doc?99902
Document Number: 81221
Rev. 1.8, 04-Feb-11
www.vishay.com
1
TSOP582.., TSOP584.., TSOP592.., TSOP594..
IR Receiver Modules for Remote
Vishay Semiconductors
Control Systems
ABSOLUTE MAXIMUM RATINGS
PARAMETER
TEST CONDITION
SYMBOL
VS
VALUE
UNIT
V
Supply voltage
- 0.3 to + 6
Supply current
IS
5
- 0.3 to 5.5
- 0.3 to (VS + 0.3)
5
mA
V
Output voltage
VO
Voltage at output to supply
Output current
VS - VO
IO
V
mA
°C
°C
°C
mW
°C
Junction temperature
Storage temperature range
Operating temperature range
Power consumption
Soldering temperature
Tj
100
Tstg
Tamb
Ptot
Tsd
- 25 to + 85
- 25 to + 85
10
Tamb 85 °C
t 10 s, 1 mm from case
260
Note
•
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability.
ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
Supply current
Supply voltage
TEST CONDITION
SYMBOL
MIN.
TYP.
0.85
0.95
MAX.
UNIT
mA
mA
V
Ev = 0, VS = 5 V
ISD
ISH
VS
0.65
1.05
Ev = 40 klx, sunlight
2.7
5.5
Ev = 0, test signal see fig. 1,
IR diode TSAL6200,
IF = 400 mA
IOSL = 0.5 mA, Ee = 0.7 mW/m2,
test signal see fig. 1
Transmission distance
Output voltage low
Minimum irradiance
d
40
m
mV
VOSL
100
Pulse width tolerance:
tpi - 5/fo < tpo < tpi + 6/fo,
test signal see fig. 1
Ee min.
0.3
45
0.45
mW/m2
tpi - 5/fo < tpo < tpi + 6/fo,
test signal see fig. 1
Maximum irradiance
Directivity
Ee max.
30
W/m2
deg
Angle of half transmission
distance
1/2
TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
Optical Test Signal
(IR diode TSAL6200, I = 0.4 A, 30 pulses, f = f , t = 10 ms)
E
e
1.0
0.9
0.8
0.7
0.6
0.5
F
0
Output Pulse Width
Input Burst Length
t
tpi
*
T
* tpi
10/f0 is recommended for optimal function
Output Signal
16110
VO
0.4
0.3
0.2
1)
7/f0 < td < 15/f0
tpi - 5/f0 < tpo < tpi + 6/f0
VOH
2)
λ = 950 nm,
Optical Test Signal, Fig.1
VOL
2)
1)
t
t
po
td
0.1
1
10
Ee - Irradiance (mW/m2)
102
103
104
105
21391
Fig. 1 - Output Active Low
Fig. 2 - Pulse Length and Sensitivity in Dark Ambient
www.vishay.com
2
Document Number: 81221
Rev. 1.8, 04-Feb-11
TSOP582.., TSOP584.., TSOP592.., TSOP594..
IR Receiver Modules for Remote
Vishay Semiconductors
Control Systems
Optical Test Signal
5.0
Ee
Correlation with Ambient Light Sources:
4.5
10 W/m2 = 1.4 kLx (Std. illum. A, T = 2855 K)
10 W/m2 = 8.2 kLx (Daylight, T = 5900 K)
4.0
3.5
t
600 µs
600 µs
3.0
2.5
2.0
t = 60 ms
94 8134
Wavelength of Ambient
Illumination: λ = 950 nm
Output Signal, (see fig. 4)
1.5
VO
1.0
0.5
0
VOH
VOL
t
0.01
0.1
1
10
100
ton
toff
Ee - Ambient DC Irradiance (W/m2)
21393
Fig. 3 - Output Function
Fig. 6 - Sensitivity in Bright Ambient
1.0
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
Ton
f = f0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
f = 30 kHz
f = 20 kHz
Toff
λ = 950 nm,
f = 10 kHz
f = 100 Hz
Optical Test Signal, Fig. 3
102
103
104
105
1
10
100
1000
0.1
1
10
Ee - Irradiance (mW/m2)
21392
21394
ΔVsRMS - AC Voltage on DC Supply Voltage (mV)
Fig. 4 - Output Pulse Diagram
Fig. 7 - Sensitivity vs. Supply Voltage Disturbances
1.2
1.0
0.8
0.6
0.4
0.2
500
450
400
350
300
250
200
150
100
50
f = f0 5 ꢀ
Δ f(3 dB) = f0/10
0.0
0
0
500
1000 1500 2000 2500 3000
f - EMI Frequency (MHz)
0.7
0.9
1.1
1.3
20747
16925
f/f - Relative Frequency
0
Fig. 5 - Frequency Dependence of Responsivity
Fig. 8 - Sensitivity vs. Electric Field Disturbances
Document Number: 81221
Rev. 1.8, 04-Feb-11
www.vishay.com
3
TSOP582.., TSOP584.., TSOP592.., TSOP594..
IR Receiver Modules for Remote
Vishay Semiconductors
Control Systems
0°
10°
20°
0.8
0.7
0.6
30°
40°
TSOP582..
TSOP592..
0.5
1.0
0.4
0.3
50°
60°
0.9
0.8
TSOP584..
0.2
TSOP594..
70°
80°
0.7
0.1
0
f = 38 kHz, Ee = 2 mW/m2
0
20
40
60
80
100
120
0.6
0.4
0.2
0
19258
21396-12
drel - Relative Transmission Distance
Burst Length (Number of Cycles/Burst)
Fig. 9 - Max. Envelope Duty Cycle vs. Burst Length
Fig. 12 - Horizontal Directivity
0°
10°
20°
0.45
0.4
30°
40°
0.35
0.3
1.0
0.9
0.8
50°
60°
0.25
0.2
70°
80°
0.7
0.15
0.6
0.4
0.2
0
- 30
- 10
10
30
50
70
90
d
- Relative Transmission Distance
19259
rel
Tamb - Ambient Temperature (°C)
21397
Fig. 10 - Sensitivity vs. Ambient Temperature
Fig. 13 - Vertical Directivity
0.50
0.45
0.40
0.35
0.30
0.25
0.20
1.2
1.0
0.8
0.6
0.4
0.2
0
750
850
950
1050
1150
1.5
2
2.5
3
3.5
4
4.5
5
5.5
94 8408
21398
λ - Wavelength (nm)
VS - Supply Voltage (V)
Fig. 11 - Relative Spectral Sensitivity vs. Wavelength
Fig. 14 - Sensitivity vs. Supply Voltage
www.vishay.com
4
Document Number: 81221
Rev. 1.8, 04-Feb-11
TSOP582.., TSOP584.., TSOP592.., TSOP594..
IR Receiver Modules for Remote
Vishay Semiconductors
Control Systems
SUITABLE DATA FORMAT
These products are designed to suppress spurious output
pulses due to noise or disturbance signals. Data and
disturbance signals can be distinguished by the devices
according to carrier frequency, burst length and envelope
duty cycle. The data signal should be close to the
band-pass center frequency (e.g. 38 kHz) and fulfill the
conditions in the table below.
When a data signal is applied to the IR receiver in the
presence of a disturbance signal, the sensitivity of the
receiver is reduced to insure that no spurious pulses are
present at the output. Some examples of disturbance
signals which are suppressed are:
0
10
15
20
5
• DC light (e.g. from tungsten bulb or sunlight)
• Continuous signals at any frequency
16920
Time (ms)
Fig. 15 - IR Signal from Fluorescent Lamp
with Low Modulation
• Strongly or weakly modulated noise from fluorescent
lamps with electronic ballasts (see figure 15 or figure 16)
0
5
10
15
20
16921
Time (ms)
Fig. 16 - IR Signal from Fluorescent Lamp
with High Modulation
TSOP582.., TSOP592..
TSOP584.., TSOP594..
Minimum burst length
10 cycles/burst
10 cycles/burst
After each burst of length
a minimum gap time is required of
10 to 70 cycles
12 cycles
10 to 35 cycles
12 cycles
For bursts greater than
a minimum gap time in the data stream is needed of
70 cycles
> 4 x burst length
35 cycles
> 10 x burst length
Maximum number of continuous short bursts/second
Recommended for NEC code
800
yes
yes
yes
yes
yes
yes
1300
yes
yes
no
Recommended for RC5/RC6 code
Recommended for Sony code
Recommended for Thomson 56 kHz code
Recommended for Mitsubishi code (38 kHz, preburst 8 ms, 16 bit)
Recommended for Sharp code
yes
yes
yes
Most common disturbance
signals are suppressed
Even extreme disturbance
signals are suppressed
Suppression of interference from fluorescent lamps
Note
•
For data formats with short bursts please see the datasheet of TSOP581.., TSOP591.., TSOP583.., TSOP593..
Document Number: 81221
Rev. 1.8, 04-Feb-11
www.vishay.com
5
TSOP582.., TSOP584.., TSOP592.., TSOP594..
IR Receiver Modules for Remote
Vishay Semiconductors
Control Systems
PACKAGE DIMENSIONS in millimeters
5
4.8
(4)
2.8
R 2
(1.54)
0.85 max.
0.5 max.
2.54 nom.
0.7 max.
2.54 nom.
1.2 0.2
Marking area
technical drawings
according to DIN
specifications
Not indicated to lerances 0.2
Drawing-No.: 6.550-5263.01-4
Issue: 12; 16.04.10
R 2
19009
www.vishay.com
6
Document Number: 81221
Rev. 1.8, 04-Feb-11
Legal Disclaimer Notice
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree
to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and
damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay
or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to
obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Document Number: 91000
Revision: 11-Mar-11
www.vishay.com
1
相关型号：
©2020 ICPDF网 联系我们和版权申明