TSOP77340 [VISHAY]
IR Receiver Modules for Remote Control Systems;型号: | TSOP77340 |
厂家: | VISHAY |
描述: | IR Receiver Modules for Remote Control Systems |
文件: | 总12页 (文件大小:297K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TSOP773.., TSOP775..
www.vishay.com
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
FEATURES
• Improved immunity against HF and RF noise
• Continuous data transmission possible
• Low supply current
• Photo detector and preamplifier in one package
• Internal filter for PCM frequency
4
• Supply voltage: 2.5 V to 5.5 V
3
2
• Improved immunity against ambient light
1
• Capable of side or top view
• Insensitive to supply voltage ripple and noise
• Two lenses for high sensitivity and wide receiving angle
20953
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
MECHANICAL DATA
Pinning:
DESCRIPTION
The TSOP773.., TSOP775.. series are
a two lens
1, 4 = GND, 2 = VS, 3 = OUT
miniaturized receiver module for infrared remote control
systems. One PIN diode per lens and a preamplifier are
assembled on a leadframe, the epoxy lens cap contains an
IR filter.
ORDERING CODE
Taping:
TSOP77...TT - top view taped
TSOP77...TR - side view taped
The TSOP773.. series devices are optimized to suppress
almost all spurious pulses from Wi-Fi and CFL sources.
They may suppress some data signals if continuously
transmitted.
New designs should prefer the TSOP773.. series containing
the newer AGC3. The TSOP775.. series are useful to
suppress even extreme levels of optical noise, but may also
suppress some data signals. Please check compatibility
with your codes.
These components have not been qualified according to
automotive specifications.
PARTS TABLE
NOISY ENVIRONMENTS
AND SHORT BURSTS (AGC3)
VERY NOISY ENVIRONMENTS
AND SHORT BURSTS (AGC5)
AGC
30 kHz
33 kHz
TSOP77330
TSOP77530
TSOP77533
TSOP77333
36 kHz
TSOP77336 (1)
TSOP77338 (2)(3)(4)(5)
TSOP77340
TSOP77536
Carrier
frequency
38 kHz
40 kHz
56 kHz
TSOP77538
TSOP77540
TSOP77356
TSOP77556
Package
Pinning
Heimdall
1, 4 = GND, 2 = VS, 3 = OUT
Dimensions (mm)
Mounting
6.8 W x 3.0 H x 3.2 D
SMD
Application
Remote control
Best remote control code
(1) MCIR (2) Mitsubishi (3) RECS-80 Code (4) r-map (5) XMP-1, XMP-2
Rev. 1.4, 22-Jul-16
Document Number: 82465
1
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP773.., TSOP775..
www.vishay.com
BLOCK DIAGRAM
Vishay Semiconductors
APPLICATION CIRCUIT
17170-11
2
R1
C1
Transmitter
with
TSALxxxx
VS
IR receiver
30 kΩ
VS
+ VS
3
OUT
Band
pass
Demo-
dulator
μC
Input
AGC
OUT
VO
1, 4
GND
GND
PIN
GND
Control circuit
20445-1
R1 and C1 recommended to reduce supply ripple for VS < 2.8 V
ABSOLUTE MAXIMUM RATINGS
PARAMETER
Supply voltage
TEST CONDITION
SYMBOL
VS
VALUE
-0.3 to +6
UNIT
V
Supply current
Output voltage
IS
VO
VS - VO
IO
Tj
Tstg
Tamb
Ptot
Tsd
5
-0.3 to 5.5
-0.3 to (VS + 0.3)
5
mA
V
V
mA
°C
°C
°C
mW
°C
Voltage at output to supply
Output current
Junction temperature
Storage temperature range
Operating temperature range
Power consumption
100
-25 to +85
-25 to +85
10
Tamb ≤ 85 °C
t ≤ 10 s, 1 mm from case
Soldering temperature
260
Note
•
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability.
ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
Supply voltage
TEST CONDITION
SYMBOL
MIN.
2.5
0.55
-
TYP.
-
0.7
0.8
MAX.
5.5
0.9
-
UNIT
V
mA
mA
VS
ISD
ISH
VS = 5 V, Ev = 0
Ev = 40 klx, sunlight
Supply current
Ev = 0, IR diode TSAL6200, IF = 250 mA,
test signal see Fig. 1
Transmission distance
Output voltage low
Minimum irradiance
d
-
-
-
40
-
-
m
mV
IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see Fig. 1
VOSL
Ee min.
100
0.4
Pulse width tolerance:
pi - 5/fo < tpo < tpi + 6/fo, test signal see Fig. 1
0.2
mW/m2
t
Maximum irradiance
Directivity
tpi - 5/fo < tpo < tpi + 6/fo, test signal see Fig. 1
Angle of half transmission distance
Ee max.
ϕ1/2
50
-
-
50
-
-
W/m2
deg
TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
0.5
0.4
0.3
0.2
0.1
0
Optical Test Signal
Ee
(IR diode TSAL6200, IF = 0.4 A, N = 6 pulses, f = f0, t = 10 ms)
λ = 950 nm,
optical test signal, Fig. 1
t
tpi *)
Output pulse width
T
*) tpi ≥ 6/f is recommended for optimal function
0
Input burst length
Output Signal
1) 3/f0 < td < 9/f0
14337
VO
2)
t
- 4/f0 < tpo < tpi + 6/f0
pi
VOH
VOL
0.1
10
1000
100 000
1)
2)
t
td
tpo
Ee - Irradiance (mW/m2)
Fig. 1 - Output Active Low
Fig. 2 - Pulse Length and Sensitivity in Dark Ambient
Rev. 1.4, 22-Jul-16
Document Number: 82465
2
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP773.., TSOP775..
www.vishay.com
Vishay Semiconductors
Optical Test Signal
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
Ee
Correlation with ambient light sources:
10 W/m2 = 1.4 klx (std. illum. A, T = 2855 K)
10 W/m2 = 8.2 klx (daylight, T = 5900 K)
Wavelength of ambient
t
λ
illumination: = 950 nm
600 µs
600 µs
t = 60 ms
94 8134
Output Signal, (see fig. 4)
VO
VOH
VOL
0.01
0.1
1
10
100
Ee - Ambient DC Irradiance (W/m2)
t
ton
toff
Fig. 3 - Output Function
Fig. 6 - Sensitivity in Bright Ambient
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
1.0
f = f0
ton
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
f = 30 kHz
toff
f = 20 kHz
f = 10 kHz
λ = 950 nm,
optical test signal, Fig. 1
f = 100 Hz
1
10
100
1000
0.1
1
10
100
1000 10 000
ΔV
- AC Voltage on DC Supply Voltage (mV)
Ee - Irradiance (mW/m2)
sRMS
Fig. 4 - Output Pulse Diagram
Fig. 7 - Sensitivity vs. Supply Voltage Disturbances
1.2
1.0
0.8
0.6
0.4
0.2
0.9
0.8
0.7
0.6
0.5
TSOP773..
0.4
0.3
0.2
f = f0 5 ꢀ
Δf(3 dB) = f0/10
0.1
TSOP775..
0.0
0
0
20
40
60
80
100 120 140
0.7
0.9
1.1
1.3
16925
f/f0 - Relative Frequency
Burst Length (number of cycles/burst)
Fig. 5 - Frequency Dependence of Responsivity
Fig. 8 - Max. Envelope Duty Cycle vs. Burst Length
Rev. 1.4, 22-Jul-16
Document Number: 82465
3
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP773.., TSOP775..
www.vishay.com
Vishay Semiconductors
0°
10°
20°
30°
40°
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0
1.0
0.9
50°
60°
0.8
70°
80°
-30
-10
10
30
50
70
90
0.6
0.4
0.2
0
Tamb - Ambient Temperature (°C)
21428
drel - Relative Transmission Distance
Fig. 9 - Sensitivity vs. Ambient Temperature
Fig. 12 - Vertical Directivity
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
750 800 850 900 950 1000 1050 1100 1150
1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5
VS - Supply Voltage (V)
21425
λ- Wavelength (nm)
Fig. 10 - Relative Spectral Sensitivity vs. Wavelength
Fig. 1 Sensitivity vs. Supply Voltage
0°
10°
20°
30°
40°
1.0
0.9
50°
60°
0.8
70°
80°
0.6
0.4
0.2
0
21427
drel - Relative Transmission Distance
Fig. 11 - Horizontal Directivity
Rev. 1.4, 22-Jul-16
Document Number: 82465
4
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP773.., TSOP775..
www.vishay.com
Vishay Semiconductors
SUITABLE DATA FORMAT
These products are designed to suppress spurious output
pulses due to noise or disturbance signals. Data and
disturbance signals can be distinguished by the devices
according to carrier frequency, burst length and envelope
duty cycle. The data signal should be close to the
band-pass center frequency (e.g. 38 kHz) and fulfill the
conditions in the table below.
When a data signal is applied to the IR receiver in the
presence of a disturbance signal, the sensitivity of the
receiver is reduced to insure that no spurious pulses are
present at the output. Some examples of disturbance
signals which are suppressed are:
0
10
15
20
5
16920
Time (ms)
• DC light (e.g. from tungsten bulb or sunlight)
• Continuous signals at any frequency
Fig. 13 - IR Disturbance from Fluorescent Lamp
with Low Modulation
• Modulated IR pattern from common fluorescent lamps
(example of noise pattern is shown in Fig. 13 or Fig. 14)
• 2.4 GHz and 5 GHz Wi-Fi
0
5
10
15
20
16921
Time (ms)
Fig. 14 - IR Disturbance from Fluorescent Lamp
with High Modulation
TSOP773..
TSOP775..
Minimum burst length
6 cycles/burst
6 cycles/burst
After each burst of length
a minimum gap time is required of
6 to 35 cycles
≥ 10 cycles
6 to 24 cycles
≥ 10 cycles
35 cycles
24 cycles
For bursts greater than
a minimum gap time in the data stream is needed of
> 4 x burst length
2000
> 25 ms
2000
Yes
Maximum number of continuous short bursts/second
MCIR code
Preferred
XMP-1, XMP-2 code
Preferred
Yes
Critical disturbance patterns
are suppressed,
e.g. highly dimmed LCDs
Mild and complex disturbance
patterns are suppressed (example:
signal pattern of Fig. 13 and Fig. 14)
Suppression of interference from fluorescent lamps
Note
For data formats with long bursts please see the datasheet for TSOP772.., TSOP774..
•
Rev. 1.4, 22-Jul-16
Document Number: 82465
5
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP773.., TSOP775..
www.vishay.com
Vishay Semiconductors
PACKAGE DIMENSIONS in millimeters
6.8
6.6 0.1
(3.4)
3.2
2.5
Mold residue
Mold residue
2.2
(0.635)
(1)
1.27
(3 x)
0.5 0.1
(4 x)
technical drawings
according to DIN
specifications
3 x 1.27 = 3.81
(2.2)
Marking area
Tool separation line
Not indicated tolerances 0.15
Proposed pad layout
from component side
(for reference only)
3 x 1.27 = 3.81
1.27
(R1.3)
Pick and place area
Drawing-No.: 6.550-5297.01-4
Issue: 4; 13.09.11
0.8
22608
ASSEMLY INSTRUCTIONS
Reflow Soldering
Manual Soldering
• Reflow soldering must be done within 72 h while stored
under a max. temperature of 30 °C, 60 % RH after
opening the dry pack envelope
• Use a soldering iron of 25 W or less. Adjust the
temperature of the soldering iron below 300 °C
• Finish soldering within 3 s
• Set the furnace temperatures for pre-heating and heating
in accordance with the reflow temperature profile as
shown in the diagram. Exercise extreme care to keep the
maximum temperature below 260 °C. The temperature
shown in the profile means the temperature at the device
surface. Since there is a temperature difference between
the component and the circuit board, it should be verified
that the temperature of the device is accurately being
measured
• Handle products only after the temperature has cooled off
• Handling after reflow should be done only after the work
surface has been cooled off
Rev. 1.4, 22-Jul-16
Document Number: 82465
6
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP773.., TSOP775..
www.vishay.com
Vishay Semiconductors
VISHAY LEAD (Pb)-FREE REFLOW SOLDER PROFILE
300
Max. 260 °C
245 °C
255 °C
250
240 °C
217 °C
200
Max. 20 s
150
Max. 100 s
Max. 120 s
100
Max. ramp up 3 °C/s
50
Max. ramp down 6 °C/s
0
0
50
100
150
t (s)
200
250
300
19800
Max. 2 cycles allowed
TAPING VERSION TSOP..TR DIMENSIONS in millimeters
16
7.5
1.75
1.34 ref.
Ø 1.5
Ø 1.5 min.
technical drawings
according to DIN
specifications
Drawing-No.: 9.700-5337.01-4
Issue: 2; 06.10.15
Rev. 1.4, 22-Jul-16
Document Number: 82465
7
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP773.., TSOP775..
www.vishay.com
Vishay Semiconductors
TAPING VERSION TSOP..TT DIMENSIONS in millimeters
16
1.75
7.5
Ø 1.5
Ø 1.5
technical drawings
according to DIN
specifications
Drawing-No.: 9.700-5338.01-4
Issue: 4; 12.06.13
Rev. 1.4, 22-Jul-16
Document Number: 82465
8
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP773.., TSOP775..
www.vishay.com
Vishay Semiconductors
REEL DIMENSIONS in millimeters
16734
LEADER AND TRAILER DIMENSIONS in millimeters
Trailer
Leader
no devices
no devices
devices
End
Start
min. 200
min. 400
96 11818
COVER TAPE PEEL STRENGTH
According to DIN EN 60286-3
0.1 N to 1.3 N
LABEL
Standard bar code labels for finished goods
The standard bar code labels are product labels and used
for identification of goods. The finished goods are packed in
final packing area. The standard packing units are labeled
with standard bar code labels before transported as finished
goods to warehouses. The labels are on each packing unit
and contain Vishay Semiconductor GmbH specific data.
300 10 mm/min.
165° to 180° peel angle
Rev. 1.4, 22-Jul-16
Document Number: 82465
9
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP773.., TSOP775..
www.vishay.com
Vishay Semiconductors
VISHAY SEMICONDUCTOR GmbH STANDARD BAR CODE PRODUCT LABEL (finished goods)
PLAIN WRITING
Item-description
Item-number
Selection-code
LOT-/serial-number
Data-code
ABBREVIATION
LENGTH
-
18
INO
8
SEL
3
BATCH
10
COD
3 (YWW)
Plant-code
PTC
2
Quantity
QTY
8
Accepted by
ACC
-
Packed by
PCK
-
Mixed code indicator
Origin
MIXED CODE
-
xxxxxxx+
Company logo
LONG BAR CODE TOP
Item-number
Plant-code
TYPE
LENGTH
N
8
N
2
Sequence-number
Quantity
X
3
N
8
Total length
-
21
SHORT BAR CODE BOTTOM
Selection-code
Data-code
TYPE
LENGTH
X
N
X
-
3
3
Batch-number
Filter
10
1
Total length
-
17
After more than 72 h under these conditions moisture
content will be too high for reflow soldering.
DRY PACKING
The reel is packed in an anti-humidity bag to protect the
devices from absorbing moisture during transportation and
storage.
In case of moisture absorption, the devices will recover to
the former condition by drying under the following condition:
Aluminum bag
192 h at 40 °C + 5 °C / - 0 °C and < 5 % RH (dry air /
nitrogen) or
96 h at 60 °C + 5 °C and < 5 % RH for all device containers
or
Label
24 h at 125 °C + 5 °C not suitable for reel or tubes.
An EIA JEDEC® standard J-STD-020 level 4 label is included
on all dry bags.
Reel
LEVEL
CAUTION
This bag contains
MOISTURE-SENSITIVE DEVICES
15973
4
1. Shelf life in sealed bag: 12 months at < 40 °C and < 90 ꢀ relative
humidity (RH)
FINAL PACKING
The sealed reel is packed into a cardboard box. A secondary
cardboard box is used for shipping purposes.
2. After this bag is opened, devices that will be subjected to soldering
reflow or equivalent processing (peak package body temp. 260 °C)
must be
2a. Mounted within 72 hours at factory condition of < 30 °C/60 ꢀ RH or
2b. Stored at < 5 ꢀ RH
3. Devices require baking befor mounting if:
Humidity Indicator Card is > 10 ꢀ when read at 23 °C 5 °C or
2a. or 2b. are not met.
RECOMMENDED METHOD OF STORAGE
4. If baking is required, devices may be baked for:
192 hours at 40 °C + 5 °C/- 0 °C and < 5 ꢀ RH (dry air/nitrogen) or
96 hours at 60 °C 5 °C and < 5 ꢀ RH for all device containers or
24 hours at 125 °C 5 °C not suitable for reels or tubes
Dry box storage is recommended as soon as the aluminum
bag has been opened to prevent moisture absorption. The
following conditions should be observed, if dry boxes are
not available:
Bag Seal Date:
(If blank, see barcode label)
Note: Level and body temperature defined by EIA JEDEC Standard J-STD-020
22522
• Storage temperature 10 °C to 30 °C
EIA JEDEC standard J-STD-020 level 4 is included
on all dry bags
• Storage humidity ≤ 60 % RH max.
Rev. 1.4, 22-Jul-16
Document Number: 82465
10
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSOP773.., TSOP775..
www.vishay.com
ESD PRECAUTION
Proper storage and handling procedures should be followed
to prevent ESD damage to the devices especially when they
are removed from the antistatic shielding bag. Electrostatic
sensitive devices warning labels are on the packaging.
Vishay Semiconductors
VISHAY SEMICONDUCTORS STANDARD
BAR CODE LABELS
The Vishay Semiconductors standard bar code labels are
printed at final packing areas. The labels are on each
packing unit and contain Vishay Semiconductors specific
data.
22178
Rev. 1.4, 22-Jul-16
Document Number: 82465
11
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of
typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding
statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a
particular product with the properties described in the product specification is suitable for use in a particular application.
Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over
time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.
Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for
such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document
or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Revision: 13-Jun-16
Document Number: 91000
1
相关型号:
©2020 ICPDF网 联系我们和版权申明