TSSP95056TT [VISHAY]
Linear Output Photo IC,;型号: | TSSP95056TT |
厂家: | VISHAY |
描述: | Linear Output Photo IC, 输出元件 光电 |
文件: | 总25页 (文件大小:676K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TSSP950..
Vishay Semiconductors
www.vishay.com
IR Sensor Module for Reflective Sensor, Light Barrier,
and Fast Proximity Applications
FEATURES
• Up to 2 m for presence and proximity sensing
• Uses modulated bursts of infrared light
• PIN diode and sensor IC in one package
• Low supply current
4
• Shielding against EMI
3
2
• Visible light is suppressed by IR filter
1
• Insensitive to supply voltage ripple and noise
• Supply voltage: 2.0 V to 3.6 V
• Material categorization: for definitions of
compliance please see www.vishay.com/doc?99912
20953
DESCRIPTION
DESIGN SUPPORT TOOLS AVAILABLE
The TSSP950.. series are compact infrared detector
modules for presence and fast proximity sensing
applications. They provide an active low output in response
to infrared bursts at 940 nm. The frequency of the burst
should correspond to the carrier frequency shown in the
parts table.
3
D
3D Models
MECHANICAL DATA
Pinning:
1, 4 = GND, 2 = VS, 3 = OUT
This component has not been qualified according to
automotive specifications.
ORDERING CODE
APPLICATIONS
Taping:
TSSP950..TT - top view taped
TSSP950..TR - side view taped
• Reflective sensors for hand dryers, towel or soap
dispensers, water faucets, toilet flush
• Vending machine fall detection
• Security and pet gates
• Person or object vicinity activation
• Fast proximity sensors for toys, robotics, drones, and
other consumer and industrial uses
PARTS TABLE
38 kHz
Carrier frequency
56 kHz
TSSP95038
TSSP95056
Package
Heimdall
Pinning
1, 4 = GND, 2 = VS, 3 = OUT
6.8 W x 3.0 H x 3.2 D
SMD
Dimensions (mm)
Mounting
Application
Presence sensors, fast proximity sensors
BLOCK DIAGRAM
PRESENCE SENSING
+3 V
2
IR emitter
VS
33 kΩ
3
Envelope
signal
OUT
Band
pass
Demo-
dulator
Input
AMP
38 kHz
+3 V
1, 4
Out to
μC
PIN
GND
16833_17
Rev. 1.0, 28-Mar-2019
Document Number: 82867
1
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSSP950..
Vishay Semiconductors
www.vishay.com
ABSOLUTE MAXIMUM RATINGS
PARAMETER
TEST CONDITION
SYMBOL
VALUE
-0.3 to +3.6
5
UNIT
V
Supply voltage
VS
IS
Supply current
mA
V
Output voltage
VO
IO
-0.3 to +3.6
5
Output current
mA
°C
Junction temperature
Storage temperature range
Operating temperature range
Power consumption
Tj
100
Tstg
Tamb
Ptot
-25 to +85
-25 to +85
10
°C
°C
Tamb ≤ 85 °C
mW
Note
•
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability
ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
SYMBOL
MIN.
2.0
0.25
-
TYP.
MAX.
UNIT
V
Supply voltage
VS
ISD
ISH
-
3.6
VS = 5 V, Ev = 0
0.37
0.8
0.45
-
mA
mA
Supply current
Ev = 40 klx, sunlight
Ev = 0,
IR diode TSAL6200,
IF = 50 mA,
Transmission distance
d
-
8
-
m
test signal see Fig. 1
IOSL = 0.5 mA, Ee = 0.7 mW/m2,
test signal see Fig. 1
Output voltage low
Minimum irradiance
VOSL
-
-
-
100
1.2
mV
Pulse width tolerance:
tpi - 5/fo < tpo < tpi + 6/fo,
test signal see Fig. 1
Ee min.
0.7
mW/m2
tpi - 5/fo < tpo < tpi + 6/fo,
test signal see Fig. 1
Maximum irradiance
Directivity
Ee max.
30
-
-
-
-
W/m2
°
Angle of half
transmission distance
ϕ1/2
50
Rev. 1.0, 28-Mar-2019
Document Number: 82867
2
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSSP950..
Vishay Semiconductors
www.vishay.com
TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
Axis Title
10000
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
Optical Test Signal
(IR diode TSAL6200, I = 0.4 A, 30 pulses, f = f , t = 10 ms)
E
e
F
0
ton
1000
t
toff
tpi
*
T
* tpi
Output Signal
1) 7/f0 < td < 15/f0
10/f0 is recommended for optimal function
100
16110
VO
VOH
2)
λ = 950 nm,
optical test signal, Fig. 3
t
- 5/f0 < tpo < tpi + 6/f0
pi
VOL
10
10 000
1)
2)
t
td
t
po
0.1
1
10
100
1000
Ee - Irradiance (mW/m2)
Fig. 1 - Output Active Low
Fig. 4 - Output Pulse Diagram
Axis Title
0.90
10000
1000
100
1.2
1.0
0.8
0.6
0.4
0.2
Output pulse width
0.85
0.80
0.75
0.70
0.65
0.60
Input burst length
f = f0 5 ꢀ
Δf(3 dB) = f0/10
λ = 950 nm,
optical test signal, Fig. 1
0.0
0.7
0.9
1.1
1.3
10
100 000
0.1
10
1000
16925
f/f0 - Relative Frequency
Ee - Irradiance (mW/m2)
Fig. 2 - Pulse Length and Sensitivity in Dark Ambient
Fig. 5 - Frequency Dependence of Responsivity
Axis Title
Optical Test Signal
2.0
10000
1000
100
Ee
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
t
600 µs
600 µs
t = 60 ms
94 8134
Output Signal, (see Fig. 4)
VO
VOH
VOL
10
t
ton
toff
-30
-10
10
30
50
70
90
Tamb - Ambient Temperature (°C)
Fig. 3 - Output Function
Fig. 6 - Sensitivity vs. Ambient Temperature
Rev. 1.0, 28-Mar-2019
Document Number: 82867
3
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSSP950..
Vishay Semiconductors
www.vishay.com
Axis Title
Axis Title
0°
10°
20°
30°
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
10000
1000
100
40°
50°
1.0
0.9
0.8
60°
70°
80°
0.7
10
1150
750
850
950
1050
0.6
0.4
0.2
0
0.2
0.4
0.6
drel. - Relative Transmission Distance
λ - Wavelength (nm)
21425
21428
Fig. 7 - Relative Spectral Sensitivity vs. Wavelength
Fig. 9 - Vertical Directivity
Axis Title
Axis Title
0°
10°
20°
30°
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
10000
1000
100
40°
50°
1.0
0.9
0.8
60°
70°
80°
0.7
10
1.0
1.5
2.0
2.5
3.0
3.5
4.0
0.6
0.4
0.2
0
0.2
0.4
0.6
drel. - Relative Transmission Distance
VS - Supply Voltage (V)
21427
Fig. 8 - Horizontal Directivity
Fig. 10 - Sensitivity vs. Supply Voltage
The typical application of these devices is a reflective or
beam break sensor with active low “detect” or “no detect”
information contained in its output. The TSSP950.. is also
suitable for fast (~ 15 ms) proximity sensor applications for
ranges between 10 cm and 2 m, if a burst pattern with
variable intensity is used.
Example for a sensor hardware:
IR Receiver
TSSP6P38
Emitter
TSAL6200
Separation to avoid
crosstalk by stray light inside
the housing
There should be no common window in front of the emitter
and detector in order to avoid crosstalk via guided light
through the window.
Rev. 1.0, 28-Mar-2019
Document Number: 82867
4
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSSP950..
Vishay Semiconductors
www.vishay.com
PACKAGE DIMENSIONS in millimeters
6.8
6.6 0.1
(3.4)
3.2
2.5
Mold residue
Mold residue
2.2
(0.635)
(1)
1.27
(3 x)
0.5 0.1
(4 x)
technical drawings
according to DIN
specifications
3 x 1.27 = 3.81
(2.2)
Marking area
Tool separation line
Not indicated tolerances 0.15
Proposed pad layout
from component side
(for reference only)
3 x 1.27 = 3.81
1.27
(R1.3)
Pick and place area
Drawing-No.: 6.550-5297.01-4
Issue: 4; 13.09.11
0.8
22608
ASSEMBLY INSTRUCTIONS
Reflow Soldering
Manual Soldering
• Reflow soldering must be done within 72 h while stored
under a max. temperature of 30 °C, 60 % RH after
opening the dry pack envelope
• Use a soldering iron of 25 W or less. Adjust the
temperature of the soldering iron below 300 °C
• Finish soldering within 3 s
• Set the furnace temperatures for pre-heating and heating
in accordance with the reflow temperature profile as
shown in the diagram. Exercise extreme care to keep the
maximum temperature below 260 °C. The temperature
shown in the profile means the temperature at the device
surface. Since there is a temperature difference between
the component and the circuit board, it should be verified
that the temperature of the device is accurately being
measured
• Handle products only after the temperature has cooled off
• Handling after reflow should be done only after the work
surface has been cooled off
Rev. 1.0, 28-Mar-2019
Document Number: 82867
5
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSSP950..
Vishay Semiconductors
www.vishay.com
VISHAY LEAD (Pb)-FREE REFLOW SOLDER PROFILE
Axis Title
300
250
200
150
100
50
10000
max. 260 °C
255 °C
240 °C
217 °C
245 °C
1000
100
10
max. 20 s
max. 120 s
max. 100 s
Max. ramp up 3 °C/s Max. ramp down 6 °C/s
Max. 2 cycles allowed
0
0
50
100
150
200
250
300
Time (s)
19800
TAPING VERSION TSSP..TR DIMENSIONS in millimeters
16
7.5
1.75
1.34 ref.
Ø 1.5
Ø 1.5 min.
technical drawings
according to DIN
specifications
Drawing-No.: 9.700-5337.01-4
Issue: 2; 06.10.15
Rev. 1.0, 28-Mar-2019
Document Number: 82867
6
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSSP950..
Vishay Semiconductors
www.vishay.com
TAPING VERSION TSSP..TT DIMENSIONS in millimeters
16
1.75
7.5
Ø 1.5
Ø 1.5
technical drawings
according to DIN
specifications
Drawing-No.: 9.700-5338.01-4
Issue: 4; 12.06.13
Rev. 1.0, 28-Mar-2019
Document Number: 82867
7
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSSP950..
Vishay Semiconductors
www.vishay.com
REEL DIMENSIONS in millimeters
16734
LEADER AND TRAILER DIMENSIONS in millimeters
Trailer
Leader
no devices
devices
no devices
End
Start
min. 200
min. 400
96 11818
COVER TAPE REEL STRENGTH
According to DIN EN 60286-3
0.1 N to 1.3 N
LABEL
Standard bar code labels for finished goods
The standard bar code labels are product labels and used
for identification of goods. The finished goods are packed in
final packing area. The standard packing units are labeled
with standard bar code labels before transported as finished
goods to warehouses. The labels are on each packing unit
and contain Vishay Semiconductor GmbH specific data.
300 10 mm/min.
165° to 180° peel angle
Rev. 1.0, 28-Mar-2019
Document Number: 82867
8
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSSP950..
Vishay Semiconductors
www.vishay.com
VISHAY SEMICONDUCTORS GmbH STANDARD BAR CODE PRODUCT LABEL (finished goods)
PLAIN WRITING
Item-description
Item-number
Selection-code
LOT-/serial-number
Data-code
ABBREVIATION
LENGTH
-
18
INO
8
SEL
3
BATCH
10
COD
3 (YWW)
Plant-code
PTC
2
Quantity
QTY
8
Accepted by
ACC
-
Packed by
PCK
-
Mixed code indicator
Origin
MIXED CODE
-
xxxxxxx+
Company logo
LONG BAR CODE TOP
Item-number
Plant-code
TYPE
LENGTH
N
8
N
2
Sequence-number
Quantity
X
3
N
8
Total length
-
21
SHORT BAR CODE BOTTOM
Selection-code
Data-code
TYPE
LENGTH
X
N
X
-
3
3
Batch-number
Filter
10
1
Total length
-
17
After more than 72 h under these conditions moisture
content will be too high for reflow soldering.
DRY PACKING
The reel is packed in an anti-humidity bag to protect the
devices from absorbing moisture during transportation and
storage.
In case of moisture absorption, the devices will recover to
the former condition by drying under the following condition:
Aluminum bag
192 h at 40 °C + 5 °C / - 0 °C and < 5 % RH (dry air /
nitrogen) or
96 h at 60 °C + 5 °C and < 5 % RH for all device containers
or
Label
24 h at 125 °C + 5 °C not suitable for reel or tubes.
An EIA JEDEC® standard J-STD-020 level 4 label is included
on all dry bags.
Reel
LEVEL
CAUTION
This bag contains
MOISTURE-SENSITIVE DEVICES
4
15973
1. Shelf life in sealed bag: 12 months at < 40 °C and < 90 ꢀ relative
humidity (RH)
FINAL PACKING
2. After this bag is opened, devices that will be subjected to soldering
reflow or equivalent processing (peak package body temp. 260 °C)
must be
The sealed reel is packed into a cardboard box.
2a. Mounted within 72 hours at factory condition of < 30 °C/60 ꢀ RH or
2b. Stored at < 5 ꢀ RH
3. Devices require baking befor mounting if:
Humidity Indicator Card is > 10 ꢀ when read at 23 °C 5 °C or
2a. or 2b. are not met.
RECOMMENDED METHOD OF STORAGE
4. If baking is required, devices may be baked for:
192 hours at 40 °C + 5 °C/- 0 °C and < 5 ꢀ RH (dry air/nitrogen) or
96 hours at 60 °C 5 °C and < 5 ꢀ RH for all device containers or
24 hours at 125 °C 5 °C not suitable for reels or tubes
Dry box storage is recommended as soon as the aluminum
bag has been opened to prevent moisture absorption. The
following conditions should be observed, if dry boxes are
not available:
Bag Seal Date:
(If blank, see barcode label)
Note: Level and body temperature defined by EIA JEDEC Standard J-STD-020
22522
• Storage temperature 10 °C to 30 °C
EIA JEDEC standard J-STD-020 level 4 label is included
on all dry bags
• Storage humidity ≤ 60 % RH max.
Rev. 1.0, 28-Mar-2019
Document Number: 82867
9
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
TSSP950..
Vishay Semiconductors
www.vishay.com
ESD PRECAUTION
VISHAY SEMICONDUCTORS STANDARD BAR
CODE LABELS (example)
Proper storage and handling procedures should be followed
to prevent ESD damage to the devices especially when they
are removed from the antistatic shielding bag. Electrostatic
sensitive devices warning labels are on the packaging.
The Vishay Semiconductors standard bar code labels are
printed at final packing areas. The labels are on each
packing unit and contain Vishay Semiconductors specific
data.
22178
Rev. 1.0, 28-Mar-2019
Document Number: 82867
10
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SMD Tape and Reel
Vishay Semiconductors
www.vishay.com
Tape and Reel Standards for Surface-Mount IR Receiver Modules
Vishay Semiconductor surface-mount IR receivers are
packaged on tape and reel. The following specification is
based on IEC publication 286, which takes the industrial
requirements for automatic insertion into account.
NUMBER OF COMPONENTS
A. Panhead: quantity per reel:
TT, top view package, 1190 pcs
TR, side view package, 1120 pcs
Absolute maximum ratings, mechanical dimensions, optical
and electrical characteristics for taped devices are identical
to the basic catalog types and can be found in the
specifications for untaped devices.
B. Heimdall: quantity per reel:
TT, top view package, 2200 pcs
TR, side view package, 2300 pcs
C. Heimdall without lens: quantity per reel:
WTT, top view package, 2200 pcs
WTR, side view package, 2300 pcs
PACKAGING
The tapes of components are available on reels. Each reel is
marked with labels which contain the following information:
D. Belobog: quantity per reel:
- Vishay
TT1, top view package, 1800 pcs
- Type
- Group
E. Belobog with shield: quantity per reel:
TT1, top view package, 1500 pcs
- Tape code, normally part of type name
- Production code
F. Minimold DF1P: quantity per reel:
DF1P, 1100 pcs
- Quantity
G. TVCastSMD TR1: quantity per reel:
TR1, side view package, 2000 pcs
MISSING COMPONENTS
Up to 3 consecutive components may be missing if the gap
is followed by at least 6 components. A maximum of 0.5 %
of the components per reel quantity may be missing. At least
5 empty positions are present at the start and the end of the
tape to enable tape insertion.
ORDER DESIGNATION
The type designation of the device is extended by
TT or TT1 for top view or TR for side view.
Tensile strength of the tape: > 15 N
Example:
TSOP6238TR (reel packing)
TSOP75238TR (reel packing)
TSOP75338WTT (reel packing)
TSOP57438TT1 (reel packing)
TSOP57238HTT1 (reel packing)
TSOP39438TR1 (reel packing)
Rev. 2.5, 08-Mar-18
Document Number: 80125
1
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SMD Tape and Reel
Vishay Semiconductors
www.vishay.com
REEL DIMENSIONS FOR PANHEAD, HEIMDALL, AND TVCASTSMD TR in millimeters
16734
Note
•
The body structure of the reel can vary
Rev. 2.5, 08-Mar-18
Document Number: 80125
2
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SMD Tape and Reel
Vishay Semiconductors
www.vishay.com
TAPING VERSION TSOP..TT (TOP VIEW) DIMENSIONS in millimeters
A. Panhead (TSOP36...TT, TSSP....TT, TSOP6...TT, TSOP16...TT, TSOP96...TT)
16584
Rev. 2.5, 08-Mar-18
Document Number: 80125
3
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SMD Tape and Reel
Vishay Semiconductors
www.vishay.com
TAPING VERSION TSOP..TT (TOP VIEW) DIMENSIONS in millimeters
B. Heimdall (TSOP75...TT, TSOP77...TT, TSSP77...TT, TSOP15...TT, TSOP95...TT)
16
1.75
7.5
Ø 1.5
Ø 1.5
technical drawings
according to DIN
specifications
Drawing-No.: 9.700-5338.01-4
Issue: 4; 12.06.13
Rev. 2.5, 08-Mar-18
Document Number: 80125
4
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SMD Tape and Reel
Vishay Semiconductors
www.vishay.com
TAPING VERSION TSOP..TT (TOP VIEW) DIMENSIONS in millimeters
C. Heimdall without lens (TSOP75...WTT, TSOP77...WTT, TSSP77...WTT, TSOP15...WTT, TSOP95...WTT)
16
1.75
7.5
Ø 1.5
Ø 1.5 min.
technical drawings
according to DIN
specifications
Drawing-No.: 9.700-5341.01-4
Issue: 3; 06.10.15
Rev. 2.5, 08-Mar-18
Document Number: 80125
5
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SMD Tape and Reel
Vishay Semiconductors
www.vishay.com
TAPING VERSION TSOP..TT1 (TOP VIEW) DIMENSIONS in millimeters
D. Belobog (TSOP37...TT1, TSOP57...TT1, TSOP17...TT1, TSOP97...TT1)
Tape and reel dimensions:
Unreel direction
Reel size “Y”
TT1 Ø 180 2 ꢀ 1800 pcs.
Tape position
coming out from reel
Ø 21 0.8
Ø 13 0.2
Label posted here
(12.4)
Parts mounted
Empty leader 400 mm min.
100 mm min. with cover tape
18.4 max.
Leader and trailer tape:
Direction of pulling out
Empty trailer 200 mm min.
Technical drawings
according to DIN
specifications
X 2:1
(Ø 1.5)
(4)
(8)
(1.2)
(0.3)
(2)
Drawing-No.: 9.700-5347.01-4
Not indicated tolerances 0.1
Issue: 2; 07.03.18
Rev. 2.5, 08-Mar-18
Document Number: 80125
6
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SMD Tape and Reel
Vishay Semiconductors
www.vishay.com
TAPING VERSION TSOP..TT1 (TOP VIEW) DIMENSIONS in millimeters
E. Belobog with shield (TSOP37...HTT1, TSOP57...HTT1, TSOP17...HTT1, TSOP97...HTT1)
Tape and reel dimensions:
Reel size “Y”
X
TT1 Ø 180 2 ꢀ 1500 pcs.
Unreel direction
Tape position
coming out from reel
Ø 21 0.8
Ø 13 0.2
Label posted here
(12.4)
18.4 max.
Parts mounted
Empty leader 400 mm min.
100 mm min. with cover tape
Leader and trailer tape:
Direction of pulling out
Empty trailer 200 mm min.
Technical drawings
according to DIN
specifications
X 2 : 1
(4)
(8)
(Ø 1.5)
(2)
(0.3)
Drawing-No.: 9.700-5380.01-4
Not indicated tolerances 0.1
Issue: 3; 07.03.18
Rev. 2.5, 08-Mar-18
Document Number: 80125
7
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SMD Tape and Reel
Vishay Semiconductors
www.vishay.com
TAPING VERSION TSOP..DF1P (SIDE VIEW) DIMENSIONS in millimeters
F. Minimold DF1P (TSOP33...DF1P, TSOP53...DF1P, TSOP13...DF1P, TSOP93...DF1P)
+3
-0
24.4
Technical drawing
according to DIN
specifications
Form of the leave open of the wheel is supplier specific.
Dimensions according to IEC EN 60 286-3
Tape width: 24
Drawing-No.: 9.800-5052.V3-4
Issue: 1; 17.12.02
Reel hub 2:1
(4)
(2)
(1.55)
B
(0.4)
(5.25)
(12)
(1.5 min.)
B
A
A
B - B
A - A
Drawing-No.: 9.700-5399.01-4
Issue: 1; 30.06.16
(6.08)
Rev. 2.5, 08-Mar-18
Document Number: 80125
8
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SMD Tape and Reel
Vishay Semiconductors
www.vishay.com
TAPING VERSION TSOP..TR (SIDE VIEW) DIMENSIONS in millimeters
G. TVCastSMD TR1 (TSOP59...TR1, TSOP39...TR1, TSOP19...TR1, TSOP99...TR1)
A-A (2 : 1)
(9.75)
(16)
(7.5)
B-B (2 : 1)
(1.75)
B
B
A
A
(Ø 1)
Technical drawings
according to DIN
specification.
Ø 1.5
Drawing-No.: GO-100220.10_Z
Issue B: 08.02.17
Rev. 2.5, 08-Mar-18
Document Number: 80125
9
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SMD Tape and Reel
Vishay Semiconductors
www.vishay.com
TAPING VERSION TSOP..TR (SIDE VIEW) DIMENSIONS in millimeters
A. Panhead (TSOP36...TR, TSSP6...TR, TSOP6...TR, TSOP16...TR, TSOP96...TR)
16585
Rev. 2.5, 08-Mar-18
Document Number: 80125
10
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SMD Tape and Reel
Vishay Semiconductors
www.vishay.com
TAPING VERSION TSOP..TR (SIDE VIEW) DIMENSIONS in millimeters
B. Heimdall (TSSP7...., TSOP75...TR, TSOP77...TR, TSSP7....TR, TSOP15...TR, TSOP95...TR)
16
7.5
1.75
1.34 ref.
Ø 1.5
Ø 1.5 min.
technical drawings
according to DIN
specifications
Drawing-No.: 9.700-5337.01-4
Issue: 2; 06.10.15
Rev. 2.5, 08-Mar-18
Document Number: 80125
11
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SMD Tape and Reel
Vishay Semiconductors
www.vishay.com
TAPING VERSION TSOP..TR (SIDE VIEW) DIMENSIONS in millimeters
C. Heimdall without lens (TSOP75...WTR, TSOP77...WTR, TSSP...WTR, TSOP15...WTR, TSOP95...WTR)
16
1.75
7.5
Ø 1.5
Ø 1.5
technical drawings
according to DIN
specifications
Drawing-No.: 9.700-5342.01-4
Issue: 2; 12.06.13
Rev. 2.5, 08-Mar-18
Document Number: 80125
12
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SMD Tape and Reel
Vishay Semiconductors
www.vishay.com
LEADER AND TRAILER DIMENSIONS in millimeters
Trailer
Leader
no devices
devices
no devices
End
Start
min. 200
min. 400
96 11818
COVER TAPE REEL STRENGTH
According to DIN EN 60286-3
0.1 N to 1.3 N
LABEL
Standard bar code labels for finished goods
The standard bar code labels are product labels and used
for identification of goods. The finished goods are packed in
final packing area. The standard packing units are labeled
with standard bar code labels before transported as finished
goods to warehouses. The labels are on each packing unit
and contain Vishay Semiconductor GmbH specific data.
300 mm/min. 10 mm/min.
165° to 180° peel angle
VISHAY SEMICONDUCTOR GmbH STANDARD BAR CODE PRODUCT LABEL (finished goods)
PLAIN WRITING
Item-description
Item-number
Selection-code
LOT-/serial-number
Data-code
ABBREVIATION
LENGTH
-
18
INO
8
SEL
3
BATCH
10
COD
3 (YWW)
Plant-code
PTC
2
Quantity
QTY
8
Accepted by
Packed by
ACC
-
PCK
-
Mixed code indicator
Origin
MIXED CODE
-
xxxxxxx+
Company logo
LONG BAR CODE TOP
Item-number
Plant-code
TYPE
LENGTH
N
8
N
2
Sequence-number
Quantity
X
3
N
8
Total length
-
21
SHORT BAR CODE TOP
Selection-code
Data-code
TYPE
LENGTH
X
N
X
-
3
3
Batch-number
Filter
10
1
Total length
-
17
Rev. 2.5, 08-Mar-18
Document Number: 80125
13
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
SMD Tape and Reel
Vishay Semiconductors
www.vishay.com
DRY PACKAGING
LEVEL
The reel is packed in an anti-humidity bag to protect the
devices from absorbing moisture during transportation and
storage.
CAUTION
This bag contains
MOISTURE-SENSITIVE DEVICES
4
Aluminum bag
1. Shelf life in sealed bag: 12 months at < 40 °C and < 90 % relative
humidity (RH)
2. After this bag is opened, devices that will be subjected to soldering
reflow or equivalent processing (peak package body temp. 260 °C)
must be
2a. Mounted within 72 hours at factory condition of < 30 °C/60 % RH or
2b. Stored at < 5 % RH
Label
3. Devices require baking befor mounting if:
Humidity Indicator Card is > 10 % when read at 23 °C 5 °C or
2a. or 2b. are not met.
4. If baking is required, devices may be baked for:
192 hours at 40 °C + 5 °C/- 0 °C and < 5 % RH (dry air/nitrogen) or
96 hours at 60 °C 5 °C and < 5 % RH for all device containers or
24 hours at 125 °C 5 °C not suitable for reels or tubes
Reel
Bag Seal Date:
(If blank, see barcode label)
15973
Note: Level and body temperature defined by EIA JEDEC Standard J-STD-020
22522
RECOMMENDED METHOD OF STORAGE
EIA JEDEC standard JSTD-020 level 4 label is included
on all dry bags
Dry box storage is recommended as soon as the aluminum
bag has been opened to prevent moisture absorption. The
following conditions should be observed, if dry boxes are
not available:
ESD PRECAUTION
Proper storage and handling procedures should be followed
to prevent ESD damage to the devices especially when they
are removed from the antistatic shielding bag. Electrostatic
sensitive devices warning labels are on the packaging.
• Storage temperature 10 °C to 30 °C
• Storage humidity ≤ 60 % RH max.
After more than 72 h under these conditions moisture
content will be too high for reflow soldering.
VISHAY SEMICONDUCTORS STANDARD
BAR CODE LABELS
In case of moisture absorption, the devices will recover to
the former condition by drying under the following condition:
The Vishay Semiconductors standard bar code labels are
printed at final packing areas. The labels are on each
packing unit and contain Vishay Semiconductors specific
data.
192 h at 40 °C + 5 °C / - 0 °C and < 5 % RH (dry air /
nitrogen) or
96 h at 60 °C + 5 °C and < 5 % RH for all device containers
or
24 h at 125 °C + 5 °C not suitable for reel or tubes.
An EIA JEDEC® standard JSTD-020 level 4 label is included
on all dry bags.
16962
OUTER PACKAGING
The sealed reel is packed into a pizza box.
CARTON BOX DIMENSIONS in millimeters
Length
Thickness
Width
22127
THICKNESS
WIDTH
LENGTH
Pizza box (SMD and heimdall)
(taping in reels)
50
340
340
Rev. 2.5, 08-Mar-18
Document Number: 80125
14
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of
typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding
statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a
particular product with the properties described in the product specification is suitable for use in a particular application.
Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over
time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk.
Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for
such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document
or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
© 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED
Revision: 08-Feb-17
Document Number: 91000
1
相关型号:
©2020 ICPDF网 联系我们和版权申明