PSPRL0801Dx-1224 [WALL]

AC/DC Switching Power Supply;
PSPRL0801Dx-1224
型号: PSPRL0801Dx-1224
厂家: WALL INDUSTRIES,INC.    WALL INDUSTRIES,INC.
描述:

AC/DC Switching Power Supply

文件: 总6页 (文件大小:687K)
中文:  中文翻译
下载:  下载PDF数据表文档文件
DATASHEET  
Rev. A  
PSPRL0801D SERIES  
Up to 240 Watts  
90~264 Vac Input  
Dual Output, Active PFC  
AC/DC Switching Power Supply  
Type E  
Type F  
Type C  
Type U  
FEATURES:  
Dual Output  
RoHS Compliant  
Remote ON/OFF  
Full Range AC Input  
4 Mechanical Options Available  
Approved to UL, TUV, CE, and CB  
Power Factor Corrected to EN61000-3-2 Class D  
Smallest 240W with 1U Height Power Density: 10.41 Watts/cu in  
DESCRIPTION:  
The PSPRL0801D series of AC/DC switching power supplies offers up to 240 Watts of output power. This  
series has dual output models with remote ON/OFF and 90~264VAC input voltage range. These supplies also  
have over voltage, short circuit, over temperature, and over power protection. Models are available in U-Chassis  
(Type U), U-Chassis with top cover (Type C), Enclosed with rear side built-in fan (Type E), and Enclosed with  
top built-in fan (Type F) designs. These supplies have UL/cUL 60950-1, TUV EN60950-1, CB, and CE Mark  
EN55022 and EN55024 safety approvals.  
Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833  
10/01/2010  
603-778-2300 www.wallindustries.com Fax 603-778-9797  
Page 1 of 6  
PSPRL0801D Series  
Up to 240 Watts  
Dual Output, Active PFC  
AC/DC Switching Power Supply  
Rev. A  
SPECIFICATIONS: PSPRL0801D Series  
All specifications are based on 25°C, Nominal Input Voltage, and Maximum Output Current unless otherwise noted.  
We reserve the right to change specifications based on technological advances.  
INPUT SPECIFICATIONS  
Input Voltage  
90 ~ 264VAC full range  
Input Frequency  
47 to 63Hz  
Input Current  
5A @ 90VAC  
Inrush Current  
Remote ON/OFF  
PFC  
35A max. @ 115VAC and 70A max. @ 230VAC; cold start.  
Designated as INH on pin 4 of CN3. Requires a low signal to inhibit output.  
Power factor correction pass EN61000-3-2 Class D.  
OUTPUT SPECIFICATIONS  
Output Voltage  
See Table  
Output Power (See Note 2)  
Output Adjustability  
Regulation  
240 Watts max. with 25CFM airflow.  
Output adjustable ±5% minimum.  
±5%  
Output Current  
See Table  
Ripple & Noise (See Note 3)  
Transient Response  
Hold-Up Time  
1% (peak to peak)  
Returns to within 1% in less than 2.5ms for a 50% load change and the peak transient does not exceed 5%.  
16ms min. at 80% of full load and 120VAC  
Overshoot  
Turn On Delay  
Turn-on & off overshoot < 5% over nominal voltage.  
1 second maximum at 120VAC.  
PROTECTION  
Over Voltage Protection  
Short Circuit Protection  
Over Temperature Protection  
Over Power Protection  
Input Fusing Protection  
Unit latching down when output exceeds 130% and recycle AC input to reset.  
Trips without damage and auto-recovery.  
Unit protected against excessive operating ambient 85°C±5°C; automatic recovery.  
Foldback mode 110~140%; auto-recovery.  
One F5A/350V fuse inserted into primary.  
GENERAL SPECIFICATIONS  
Switching Frequency  
Efficiency  
70KHz fixed frequency.  
70% typical (Measured at 230VAC and full load).  
1500VAC input line to chassis (10mA DC cut-off current). 3000VAC primary to secondary windings; 1500VAC  
primary to core. All for 3 sec.  
Withstand Voltage  
Leakage Current  
Burn In  
3.5mA @ 240VAC  
45 ±5°C for 1 hour @ 230VAC with full load.  
Designated as PG on CN3 and TTL high 100-500ms after DC regulation. It goes low at least 1ms before loss of  
regulation and has ability to sink 100mA.  
Power Good  
Power Supply On  
Grounding Test  
Fan Drive  
Green LED designated as LED1 on the PCB.  
Apply 25A from ground pin of the three prong plug to the far most earth. Max. allowable resistance is 0.1.  
12VDC/300mA offering to drive an external fan.  
Designated as FF on pin 3 of CN3 is an open collector output rated for 28VDC/5mA sink current maximum; it will  
go high when a fan failure is detected.  
Fan Fail (FF) Alarm  
ENVIRONMENTAL SPECIFICATIONS  
Operating Temperature  
Storage Temperature  
Operating Humidity  
0°C to +70°C ambient, de-rating at 2.5% per degree from 50°C to 70°C.  
-20°C to +85°C  
5% to 90% RH, non-condensing  
Storage Humidity  
5% to 95% RH, non-condensing  
Vibration  
5 ~ 50Hz, acceleration ±7.35 m/(s x s) on X, Y, and Z axis.  
U Type (U-Chassis): 240W max with 25CFM forced airflow or 120W under convection cooling.  
C Type (U-Chassis with top cover): 240W max with 25CFM forced airflow or 120W under convection cooling.  
E Type (Enclosed with rear side built-in fan): 240W max.  
Cooling (See Note 2)  
F Type (Enclosed with top built-in fan): 240W max.  
MTBF  
100,000 hours (according to MIL-HBK-217F) at 30°C.  
PHYSICAL SPECIFICATIONS  
U Type (U-Chassis): 17.64oz (500g)  
C Type (U-Chassis with top cover): 19.40oz (550g)  
E Type (Enclosed with rear side built-in fan): 22.93oz (650g)  
F Type (Enclosed with top built-in fan): 21.16oz (600g)  
Weight  
U Type (U-Chassis): 5 x 3.2 x 1.5 inches (127.00 x 81.28 x 38.10 mm)  
C Type (U-Chassis with top cover): 5 x 3.2 x 1.66 inches (127.00 x 81.28 x 42.10 mm)  
E Type (Enclosed with rear side built-in fan): 6.5 x 3.2 x 1.6 inches (165.10 x 81.28 x 40.64 mm)  
F Type (Enclosed with top built-in fan): 5 x 3.2 x 2 inches (127.00 x 81.28 x 50.8 mm)  
Dimensions (L x W x H)  
SAFETY  
Emissions  
FCC Part 15, CISPR 22 class B, conducted.  
Safety Regulations  
Approved to UL60950-1, TUV EN60950-1, CE Mark EN55022 & EN55024 regulations and CB.  
Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833  
10/01/2010  
603-778-2300 www.wallindustries.com Fax 603-778-9797  
Page 2 of 6  
PSPRL0801D Series  
Up to 240 Watts  
Dual Output, Active PFC  
AC/DC Switching Power Supply  
Rev. A  
MODEL SELECTION TABLE  
Maximum Output Current  
Maximum Output Power (2)  
Input Voltage  
Range  
Model (1)  
Output Voltage  
Type U  
(Convection)  
Types E, F, C, & U  
(forced air)  
Type U  
(Convection)  
Types E, F, C, & U  
(forced air)  
V1  
V2  
V1  
V2  
V1  
V2  
V1  
V2  
+5VDC  
+12VDC  
+5VDC  
12A  
6.67A  
12A  
24A  
13.33A  
24A  
PSPRL0801Dx-0512  
PSPRL0801Dx-0524  
PSPRL0801Dx-0548  
PSPRL0801Dx-1224  
90 ~ 264VAC  
90 ~ 264VAC  
90 ~ 264VAC  
90 ~ 264VAC  
120W  
120W  
120W  
120W  
240W  
240W  
240W  
240W  
+24VDC  
+5VDC  
3.33A  
12A  
6.67A  
24A  
+48VDC  
+12VDC  
+24VDC  
1.67A  
6.67A  
3.33A  
3.33A  
13.33A  
6.67A  
NOTES  
1. Mechanical Options: The “x” in the model number can be U for U-chassis type, C for U-chassis with top cover, E for enclosed type with rear side  
built-in fan, or F for enclosed type with top side built-in fan.  
2. U Type Models: U-Chassis @ 240W max. with 25CFM max. forced airflow or 120W convection cooled output.  
C Type Models: U-Chassis with top cover @ 240W max. with 25CFM max. forced airflow or 120W convection cooled output.  
E Type Models: Enclosed with rear side built-in fan @ 240W max.  
F Type Models: Enclosed with top built-in fan @ 240W max.  
3. Ripple and noise is measured from 10KHZ to 20MHz bandwidth at output with 0.1μF ceramic and 22μF electrolytic capacitors in parallel.  
4. Provides peak power to 600W within 500µs for all models; for longer duty duration must contact manufacturer.  
5. 10% minimum load is required to maintain the ripple and regulation specifications.  
6. Output is fully isolated.  
MECHANICAL DRAWINGS  
Type “U” Models (U-Chassis): 5(L) x 3.2(W) x 1.5(H) Inches; Weight: 17.64oz  
Unit: mm [inches]  
5.00 [0.20]  
4.50 [0.18]]  
OUTPUT PIN ASSIGNMENT  
Howder  
V1:Pin 3  
Molex  
V1:Pins 6 ~ 8  
RTN: Pins 2 ~ 5  
V2: Pin 1  
RTN: Pin 2  
V2: Pin 1  
Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833  
603-778-2300 www.wallindustries.com Fax 603-778-9797  
10/01/2010  
Page 3 of 6  
PSPRL0801D Series  
Up to 240 Watts  
Dual Output, Active PFC  
AC/DC Switching Power Supply  
Rev. A  
Type “C” Models (U-Chassis with Top Cover): 5(L) x 3.2(W) x 1.66(H) Inches; Weight: 19.40oz  
Unit: mm [inches]  
OUTPUT PIN ASSIGNMENT  
Howder  
V1:Pin 3  
Molex  
V1:Pins 6 ~ 8  
RTN: Pins 2 ~ 5  
V2: Pin 1  
RTN: Pin 2  
V2: Pin 1  
Type “E” Models (Enclosed with Rear Side Built-in Fan): 6.5(L) x 3.2(W) x 1.6(H) Inches; Weight: 22.93oz  
Unit: mm [inches]  
6.35  
[0.25]  
114.30 [4.50]  
68.58 [2.70]  
44.52 [1.75]  
40.64 [1.60]  
5.00 [0.20]  
4.50 [0.18]  
64.77 [2.55]  
81.28 [3.20]  
8.26 [0.32]  
OUTPUT PIN ASSIGNMENT  
Howder  
V1:Pin 3  
Molex  
V1:Pins 6 ~ 8  
165.10 [6.50]  
RTN: Pin 2  
V2: Pin 1  
RTN: Pins 2 ~ 5  
V2: Pin 1  
Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833  
603-778-2300 www.wallindustries.com Fax 603-778-9797  
10/01/2010  
Page 4 of 6  
PSPRL0801D Series  
Up to 240 Watts  
Dual Output, Active PFC  
AC/DC Switching Power Supply  
Rev. A  
Type “F” Models (Enclosed with Top Built-in Fan): 5(L) x 3.2(W) x 2(H) Inches; Weight: 21.16oz  
Unit: mm [inches]  
50.80 [2.00]  
OUTPUT PIN ASSIGNMENT  
Howder  
V1:Pin 3  
Molex  
V1:Pins 6 ~ 8  
RTN: Pins 2 ~ 5  
V2: Pin 1  
RTN: Pin 2  
V2: Pin 1  
63.50 [2.50]  
114.30 [4.50]  
I/O CONNECTOR PIN ASSIGNMENT  
Input Connector (CN1):  
Molex Part No. 09-91-0050 or equivalent (5pin, 3used), PCB is Labeled: L=Line; N=Neutral;  
G=Chassis Ground Mating Pins; Moles Engineering Series 2478, 2578, 8818.  
Terminal block - Howder M3 Part No. HD-601-3P  
Output Connector (CN2):  
Molex Part No. 09-91-0800  
Terminal block - Howder M3 Part No. HD-816-3P  
Output Pin Assignment:  
DUAL OUTPUT  
Howder  
V1:Pin 3  
Molex  
V1:Pins 6 ~ 8  
RTN: Pins 2 ~ 5  
V2: Pin 1  
RTN: Pin 2  
V2: Pin 1  
Mounting Inserts:  
6 Paces M3x0.7. Maximum Penetration 4mm see outline drawing for location.  
Logic Signal Connector (CN3):  
Mating JST XHP-4 or equivalent (CHYAO SHIUNN JS-2001-04);  
Mating Pins: JST SXH-002T-P0.6 FOR AWG 30 to 26.  
Fan driver connector (FAN2):  
Mating connector is JST P/N XHP-3 (3 pins 0.98 pitch) or equivalent (CHYAO SHIUNN JS-2001-03).  
Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833  
10/01/2010  
603-778-2300 www.wallindustries.com Fax 603-778-9797  
Page 5 of 6  
PSPRL0801D Series  
Up to 240 Watts  
Dual Output, Active PFC  
AC/DC Switching Power Supply  
Rev. A  
COMPANY INFORMATION  
Wall Industries, Inc. has created custom and modified units for over 50 years. Our in-house research and development  
engineers will provide a solution that exceeds your performance requirements on-time and on budget. Our ISO9001-2008  
certification is just one example of our commitment to producing a high quality, well-documented product for our customers.  
Our past projects demonstrate our commitment to you, our customer. Wall Industries, Inc. has a reputation for working  
closely with its customers to ensure each solution meets or exceeds form, fit and function requirements. We will continue to  
provide ongoing support for your project above and beyond the design and production phases. Give us a call today to discuss  
your future projects.  
Contact Wall Industries for further information:  
Phone:  
Toll Free:  
Fax:  
(603)778-2300  
(888)597-9255  
(603)778-9797  
E-mail:  
Web:  
Address:  
sales@wallindustries.com  
www.wallindustries.com  
5 Watson Brook Rd.  
Exeter, NH 03833  
Wall Industries, Inc. 5 Watson Brook Road Exeter, NH 03833  
603-778-2300 www.wallindustries.com Fax 603-778-9797  
10/01/2010  
Page 6 of 6  

相关型号:

SI9130DB

5- and 3.3-V Step-Down Synchronous Converters

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135LG-T1

SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135LG-T1-E3

SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135_11

SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9136_11

Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130CG-T1-E3

Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130LG-T1-E3

Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130_11

Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137

Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137DB

Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137LG

Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9122E

500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification Drivers

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY