DSL240PS12-I [XPPOWER]

Ultra Slim Design;


型号：	DSL240PS12-I
厂家：	XP POWER LIMITED
描述：	Ultra Slim Design
文件：	总2页 (文件大小：193K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

xppower.com

240 Watts

DSL240 Series

•

Ultra Slim Design

150% Peak Load for 3 seconds

Full Power from ꢀ40 °C to +60°C

High Efficiency – Up to 93%

Hazardous Locations Approval

Parallel Capability

3 Year Warranty

Specification

Input

General

Input Voltage

Input Frequency

Input Current

Inrush Current

Power Factor

• 88-264 VAC (120-375 VDC)

• 47-63 Hz

• 2.3 A at 115 VAC, 1.15 A at 230 VAC

• 24/48 A max at 115/230 VAC

• 0.97 typical at 230 VAC

Conforms to EN61000-3-2 Class A.

Efficiency

Isolation

• See table

• 3000 VAC Input to Output

1500 VAC Input to Ground

500 VAC Output to Ground

• 100 kHz typical PFC & main converter at

230 VAC and full load

• Volt free contacts rated at 60 VDC/ 0.3 A

on 24 V versions only

• Green LED to indicate output on. Red LED

to indicate low output voltage. See

mechanical details for operating range.

Switching Frequency

DC OK Signal

Earth Leakage Current • 3.5 mA maximum

Input Protection

• Internal fuse in line, T5.0 A/250 VAC

Output LED

Output

Output Voltage

• See table

• +1% at 100% load

• No minimum load required

• 1.0 s max

MTBF

• >370 kHrs to BELLCORE Issue 6 at 40 °C,

Output Voltage Trim

Initial Set Accuracy

Minimum Load

Environmental

Operating Temperature • -40 °C to +70 °C (see derating curves)

Start Up Delay

Cooling

Operating Humidity

Protection

Storage Temperature • -40 °C to +85 °C

Operating Altitude

Shock

• Natural convection

• 20-95% RH, non-condensing

• IP20

Start Up Rise Time

Hold Up Time

Line Regulation

Load Regulation

Transient Response

• 150 ms max

• 25 ms minimum at full load and 115 VAC

•

1% ( 5% in parallel mode)

• 4850 m

• 10% maximum deviation, recovering to

less than 1% within 2 ms for 50% step

load change at 0.2 A/µs

• IEC68-2-27, 4 g, 22 ms half sine, 3 times

in each of 6 axes

Ripple & Noise

• 100 mV pk-pk maximum, measured with

20 MHz bandwidth

Vibration

• IEC68-2-6, 10-500 Hz, 2 g 10 mins/sweep.

60 mins for each of 3 axes

Overvoltage Protection • 12 V output: 15-16.5 V,

24 V output: 30-33 V

• 120-150% of rated current

(see application note)

EMC & Safety

Emissions

Harmonic Currents

Voltage Flicker

ESD Immunity

Overload Protection

• EN55022, class B conducted & radiated

• EN61000-3-2, class A

• EN61000-3-3

• EN61000-4-2, 8 KV Contact,

15 KV Air Discharge, Perf Criteria A

• EN61000-4-3, 10 V/m Perf Criteria A

• EN61000-4-4, level 4 Perf Criteria A

• EN61000-4-5, Installation Class 4

Perf Criteria A

Short Circuit Protection • Trip and restart (hiccup mode)

auto recovery within 7 s

0.03%/°C

Temperature

Coefficient

Thermal Protection

•

Radiated Immunity

EFT/Burst

Surge

• 110°C max, measured on internal heatsink

auto recovery

• A maximum of 3 units can be paralleled.

Max power available is 90% of total rated

power. Minimum load of 10% required per

unit

Parallel Operation

Conducted Immunity

Magnetic Field

• EN61000-4-6, 10 V Perf Criteria A

• EN61000-4-8, level 4, Perf Criteria A

• EN55024, 30% 10 ms, 60% 100 ms,

100% 5000 ms Perf Criteria A, B, B

Maximum Capacitive

Load

• 7000 µF (start up delay increases to 1.5s

and rise time to 500 ms)

Dips & Interruptions

Safety Approvals

• UL508, UL60950-1, EN60950-1, ANSI/ISA

12.12.01 (Class I, Division 2, Groups A, B,

C and D)

DSL240

Typical Efficiency⁽²⁾Model Number⁽¹⁾

Models and Ratings

Output Voltage

Output Power Output Voltage Trim⁽⁴⁾Output Current

Peak Load⁽³⁾

24.0 A

12 V

24 V

192 W

240 W

11.75-14.5 V

22.5-28.5 V

16.0 A

10.0 A

90%

93%

DSL240PS12-I

DSL240PS24-I

15.0 A

Notes

1. Add suffix ‘D’ for detachable connector option e.g. DSL240PS24-ID.

2. Typical efficiency at 230 VAC and full load.

3. Peak load is for a maximum of 3 s with 20% duty cycle. Average power is not

to exceed nominal output power.

4. Output current should be limited so that nominal output power is

not exceeded.

Mechanical Details

The green LED is lit if the output voltage is OK (10-11.2 VDC for 12 V units, 17.6-19.4 VDC for 24 V units at start up)

The red LED is lit if the output voltage is low (10-11.2 VDC for 12 V units, 17.6-19.4 VDC for 24 V units after start up)

0.3

(7.0)

4.59 (116.6)

Pin Connections

Conn Pin Designation

Ground

Neutral

Line

Input

5.65

(143.5)

DC OK*

Positive

Negative

4.9

(124.50)

Output

* 24 V models only.

2.52 (64.0)

‘-D’ version (detachable connectors)

Notes

1. All dimensions in inches (mm)

2. Weight: 1.916 lbs (860g)

3. Tolerance: 0.02 in ( 0.5 mm)

4. Screw terminal: 10-24 AWG cables size. Detachable connector version: 14-24 AWG cable size.

5. Connection screw maximum torque: Input: 9lbs-in (1.0 Nm), Output: 5.5 lbs-in (0.6 Nm).

Application Notes

Derating Curves

DC OK

100

DCOK

Open = Output fail

Closed = Output good

Contact Rating: 0.3 A at 60 VDC

500 VDC isolation

-40

-20

Ambient Temp (˚C)

Peak Loading

258 W for 12 V

360 W for 24 V

Peak

3 sec

Auto recovery within 7 sec

198 W for 12 V

240W for 24 V

Continuous

OCP

< 7 sec

OCP

< 7 sec

04-Jan-13

相关型号：