ECP150PS48 [XPPOWER]

AC-DC Regulated Power Supply Module, 150W,;


型号：	ECP150PS48
厂家：	XP POWER LIMITED
描述：	AC-DC Regulated Power Supply Module, 150W, 输出元件
文件：	总2页 (文件大小：455K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

150 Watts

xppower.com

ECP Series

•

100 W Convectionꢀcooled

150 W Forcedꢀcooled

2” x 4” Foot Print

Single Outputs from 12 V to 48 V

Builtꢀin Fan Supply

<0.5 W No Load Input Power

3 Year Warranty

Specification

Input

General

Efficiency

Isolation

• See table

Input Voltage

• 90-264 VAC (120-370 VDC),

Derate from 100% load at 100 VAC to

90% load at 90 VAC

• 47-63 Hz

• 1.5 A max at 115 VAC, 0.75 A max at

230 VAC

• 4000 VAC Input to Output

1500 VAC Input to Ground

500 VDC Output to Ground

• Primary to Secondary: 2 MOPP

Primary to Earth: 1 MOPP

• 60 kHz 10 kHz

• 300 kHrs to MIL-HDBK-217F at 25 °C, GB

Input Frequency

Input Current

Protection Level

Switching Frequency

MTBF

Inrush Current

Power Factor

• 60 A max at 230 VAC, cold start at 25 °C

• >0.95 at full load, 230 VAC

Environmental

Operating Temperature • -20 °C to +70 °C derate from 100% load

Earth Leakage Current • 230 µA at 264 VAC, 60 Hz.

No Load Input Power • <0.5 W

Input Protection

at 50 °C to 50% load at 70 °C

• Convection cooled: 100 W

Forced cooled: 150 W with 10 CFM

• Internal T3.15A/250VAC fitted in line and

neutral

Cooling

Operating Humidity

Operating Altitude

• 5% to 90% RH, non condensing

• 3000 m

Output

Storage Temperature • -40 °C to +85 °C

Output Voltage

• See tables

Shock

• IEC68-2-6, 30 g, 11 mins half sine, 3 times

in each of 6 axes

Output Voltage Trim

Initial Set Accuracy

Minimum Load

•

10%

1% at 50 % load

Vibration

• IEC68-2-27, 10-55 Hz, 2 g 10 mins /

sweep. 60 mins for each of 3 axes

• No minimum load requirement

• 550 ms typical

• 35 ms typical

Start Up Delay

EMC & Safety

Start Up Rise Time

Hold Up Time

Emissions

• EN55022/11, Level B conducted &

Level A radiated

• 16 ms minimum at full load and 115 VAC

Line Regulation

Load Regulation

Transient Response

•

0.5% max

Harmonic Currents

• EN61000-3-2 Class A

EN61000-3-2 Class C for load >60 W

Voltage Flicker

ESD Immunity

• EN61000-3-3

• EN61000-4-2, 8 kV air, 4 kV contact,

Perf Criteria A

• 4% maximum deviation, recovering to less

than 1% within 500 µs for 25% step load

• 1% max pk-pk, 20 MHz bandwidth,

(see note 2)

Ripple & Noise

Radiated Immunity

EFT/Burst

• EN61000-4-3, 10 V/m, Perf Criteria A

• EN61000-4-4, level 3, Perf Criteria A

Overvoltage Protection • 115% - 140% of nominal voltage on main

Surge

• EN61000-4-5, installation class 3,

Perf Criteria A

output. Recycle mains to reset.

• 110-150%

Overload Protection

Conducted Immunity

Dips & Interruptions

• EN61000-4-6, 10 V, Perf Criteria A

• EN55024, 100% 10 ms,

Short Circuit Protection • Trip and restart (hiccup)

Temperature

Coefficient

• 0.02%/°C

30%, 500 ms, 100%, 5000 ms

Perf Criteria A, A, B for high line,

A, B, B for low line at full load,

EN60601-1-2, 30% 500 ms, 60% 100 ms,

100% 10 ms, 100% 5000 ms,

Perf Criteria A, A, A, B for high line,

A, B, A, B for low line at full load

Fan Supply

• 12 V at 500 mA

Safety Approvals

• UL60950-1, IEC60950-1, EN60950-1,

ANSI/AAMI ES 60601-1, IEC60601-1,

EN60601-1

ECP150

Models and Ratings

Output Current

Convection-cooled Forced-cooled⁽¹⁾

Ripple and Noise

pk-pk⁽²⁾

Output Voltage

Fan Output

Efficiency⁽³⁾

Model Number

12.0 V

15.0 V

24.0 V

28.0 V

48.0 V

8.33 A

6.67 A

4.17 A

3.50 A

2.08 A

12.50 A

10.00 A

6.25 A

5.40 A

3.10 A

120 mV

150 mV

240 mV

280 mV

480 mV

12 V/0.5 A

91%

92%

ECP150PS12

ECP150PS15

ECP150PS24

ECP150PS28

ECP150PS48

Notes

1. Requires 10 CFM.

2. Measured with 20 MHz bandwidth and 10 µF electrolytic capacitor in parallel

with 0.1 µF ceramic capacitor

3. Minimum average efficiencies measured at 25%, 50%, 75% & 100% of

150 W load and 230 VAC input.

Mechanical Details

TB1 - Input Connector

Pin 1

Pin 2

Pin 3

Line

Not Fitted

Neutral

4.00 (101.6)

Voltage Adj.

3.75 (95.2)

Mates with JST housing

VHR-3N and JST Series

SVH-21T-P1.1 crimp terminals

TB3

Mounting holes marked with

must be connected to safety earth

2.00

1.75

(44.45)

TB1

(50.8)

TB2

TB2 - Output Connector

Pin 1

Pin 2

Pin 3

Pin 4

Pin 5

Pin 6

+Vout

-Vout

0.134 (3.4)

Mates with JST housing

VHR-6N and JST Series

SVH-21T-P1.1 crimp terminals

1.16

(29.5)

TB3 - Fan Connector

Pin 1

Pin 2

Fan +

Fan -

Mates with Molex housing

22-01-1022 and 2759 crimp

terminals

0.06 (1.6)

0.10 (2.5)

Notes

1. All dimensions shown in inches (mm).

Tolerance: 0.02 (0.5)

2. Weight: 0.42 lbs (190 g) approx.

Derating Curve

100

-20

-10

Ambient Temperature (ºC)

30-Sept-13

相关型号：