232273564471 [YAGEO]
Fixed Resistor, Metal Glaze/thick Film, 1W, 470ohm, 200V, 5% +/-Tol, -100,100ppm/Cel, 1218;
| 型号： | 232273564471 |
| 厂家： | 
YAGEO CORPORATION |
| 描述： | Fixed Resistor, Metal Glaze/thick Film, 1W, 470ohm, 200V, 5% +/-Tol, -100,100ppm/Cel, 1218 |
| 文件： | 总10页 (文件大小：253K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
GENERAL PURPOSE CHIP RESISTORS
RC1218 (Pb Free)
5%, 1%
Product specification
2
10
SERIES
1218 (Pb Free)
RC
Chip Resistor Surface Mount
SCOPE
This specification describes RC1218 series chip resistors with lead-free terminations made by thick film process.
ORDERING INFORMATION
Part number is identified by the series, size, tolerance, packing type, temperature coefficient, taping reel and
resistance value.
PHYCOMP ORDERING CODE
12NC CODE
CTC CODE
2322
(1)
XXX XXXXX L
RC1218 X X X XX XXXX L
( ) ( ) ( ) ( )
( )
5
( )
6
1
2
3
4
( )
(2)
(3)
4
EMBOSSED TAPE ON REEL (units) (2)
4,000
( )
1 TOLERANCE
TYPE/ START TOL.
RESISTANCE
RANGE
1218 IN (1)
(%)
F = ±1%
J = ±5%
PRC201
2322
±5%
±1%
-
1 to 1 MΩ
1 to 1 MΩ
0 Ω
735 64xxx
735 7xxxx
735 90007
( )
PRC201 2322
Jumper 2322
2 PACKAGING TYPE
K = Embossed taping reel
( )
3 TEMPERATURE COEFFICIENT
OF RESISTANCE
(1) The resistors have a 12-digit
ordering code starting with
2322.
Last digit of 12NC
Resistance decade (3)
Last digit
– = Base on spec
X
0.01 to 0.0976
0
7
8
9
1
2
3
4
5
6
( )
4 TAPING REEL
(2) The subsequent 4 or 5 digits
indicate the resistor
X
0.1 to 0.976
07 = 7 inch dia. Reel
X
1 to 9.76
tolerance and packaging.
( )
5 RESISTANCE VALUE
X
10 to 97.6
100 to 976
1 to 9.76 k
(3) The remaining 4 or 3 digits
represent the resistance value
with the last digit indicating
the multiplier as shown in the
table of “Last digit of 12NC”.
5R6, 56R, 560R, 5K6, 56K, 22M
X
X
(6) RESISTOR TERMINATIONS
X
10 to 97.6 k
L = Lead free terminations (pure Tin)
X
100 to 976 k
(4) “L” means lead-free
terminations.
X
1 to 9.76 M
ORDERING EXAMPLE
X
10 to 97.6 M
ORDERING EXAMPLE
The ordering code of a RC1218
chip resistor, value 56 X with
±1% tolerance, supplied in 7-inch
X
Example: 0.02
=
=
=
=
=
0200 or 200
3007 or 307
1008 or 108
3303 or 333
1006 or 106
The ordering code of a PRC201
resistor, value 56 X with ±1%
tolerance, supplied in tape of
4,000 units per reel is:
X
0.3
X
1
tape reel is: RC1218FK-0756RL.
X
33 k
232273575609L.
X
10 M
NOTE
1. The “L” at the end of the code is only for ordering. On the reel label, the standard CTC or 12NC will be mentioned an additional stamp
“LFP”= lead free production.
2. Products with lead in terminations fulfil the same requirements as mentioned in this datasheet.
3. Products with lead in terminations will be phased out in the coming months (before July 1st, 2006)
www.yageo.com
Oct 13, 2004 V.1
Product specification
3
10
SERIES
1218 (Pb Free)
RC
Chip Resistor Surface Mount
MARKING
RC1218
E-24 series: 3 digits
First two digits for significant figure and 3rd digit for number of zeros
YNSC023
Fig. 1 Value=100 Ω
Both E-24 and E-96 series: 4 digits
First three digits for significant figure and 4th digit for number of zeros
YNSC024
Fig. 2 Value=10 KΩ
For marking codes, please see EIA-marking code rules in data sheet “Chip resistors instruction”.
CONSTRUCTION
The resistors are constructed out of
protective coat
a high-grade ceramic body. Internal
metal electrodes are added at each
end and connected by a resistive
paste. The composition of the paste
is adjusted to give the approximate
required resistance and laser cutting
of this resistive layer that achieves
tolerance trims the value. The
handbook, 4 columns
resistor layer
inner electrode
H
end termination
ceramic substrate MBE940_a
I
2
Fig. 3 Chip resistor construction
resistive layer is covered with a
protective coat and printed with the
resistance value. Finally, the two external terminations (pure Tin) are added. See fig. 3.
DIMENSIONS
Table 1
For dimension see Table 1
protective coat
TYPE
RC1218
I
1
L (mm)
W (mm)
H (mm)
I1 (mm)
I2 (mm)
3.10 ±0.10
4.60 ±0.10
0.55 ±0.10
0.45 ±0.20
0.40 ±0.20
W
YNSC025
L
Fig. 4 Chip resistor dimension
www.yageo.com
Oct 13, 2004 V.1
Product specification
4
10
SERIES
1218 (Pb Free)
RC
Chip Resistor Surface Mount
ELECTRICAL CHARACTERISTICS
FOOTPRINT AND SOLDERING
PROFILES
Table 2
For recommended footprint and
soldering profiles, please see the
special data sheet “Chip resistors
mounting”.
RC1218 1 W
CHARACTERISTICS
Operating Temperature Range
Maximum Working Voltage
Maximum Overload Voltage
Dielectric Withstanding Voltage
–55 °C to +155 °C
200 V
500 V
500 V
ENVIRONMENTAL DATA
5% (E24) 1 Ω to 1 MΩ
1% (E96) 1 Ω to 1 MΩ
For material declaration
information (IMDS-data) of the
products, please see the
separated info “Environmental
data”.
Resistance Range
Zero Ohm Jumper < 0.02 Ω
10 Ω < R ≤ 1 MΩ ±100 ppm/°C
1 Ω < R ≤ 10 Ω ±200 ppm/°C
Temperature Coefficient
Jumper Criteria
Rated Current
6.0 A
Maximum Current
10.0 A
PACKING STYLE AND PACKAGING QUANTITY
Table 3 Packing style and packaging quantity
PRODUCT TYPE
RC1218
PACKING STYLE
REEL DIMENSION
7" (178 mm)
QUANTITY PER REEL
Embossed taping reel (K)
4,000 units
NOTE
1. For embossed tape and reel specification/dimensions, please see the special data sheet “Packing” document.
www.yageo.com
Oct 13, 2004 V.1
Product specification
5
10
SERIES
1218 (Pb Free)
RC
Chip Resistor Surface Mount
FUNCTIONAL DESCRIPTION
POWER RATING
MRA632
P
max
RC1218 rated power at 70°C is 1 W
RATED VOLTAGE
(%P
)
rated
100
50
0
The DC or AC (rms) continuous working voltage
corresponding to the rated power is determined by
the following formula:
V=√(P X R)
−55
0
50 70 100
T
155
(°C)
amb
Where
V=Continuous rated DC or
AC (rms) working voltage (V)
Fig. 5 Maximum dissipation (P ) in percentage of rated power
max
as a function of the operating ambient temperature (T
)
amb
P=Rated power (W)
R=Resistance value (X)
PULSE LOADING CAPABILITIES
MBD582
4
10
V
max
(V)
1.2/50 µs
10/700 µs
3
10
2
10
10
10
2
3
4
5
6
7
10
10
10
10
10
10
R
(Ω)
n
Fig. 6 Maximum permissible peak pulse voltage without failing to open circuit’ in accordance with DIN IEC 60040 (CO) 533 for type:
RC1218
www.yageo.com
Oct 13, 2004 V.1
Product specification
6
10
SERIES
1218 (Pb Free)
RC
Chip Resistor Surface Mount
MLB883
3
10
P
max
(W)
single pulse
2
10
A
B
t
/t =1000
i
p
10
100
2
1
1
10
6
5
4
3
2
1
10
10
10
10
10
10
1
t
(s)
i
Fig. 7 Pulse on a regular basis for type: RC1218; maximum permissible peak pulse power as a function of pulse duration for single
pulse and repetitive pulse tp/ti = 1000
MLB884
800
V
max
(V)
600
400
200
0
6
5
4
3
2
1
10
10
10
10
10
10
1
t
(s)
i
Fig. 8 Pulse on a regular basis for type: RC1218; maximum permissible peak pulse voltage as a function of pulse duration
www.yageo.com
Oct 13, 2004 V.1
Product specification
7
10
SERIES
1218 (Pb Free)
RC
Chip Resistor Surface Mount
TESTS AND REQUIREMENTS
Table 4 Test condition, procedure and requirements
TEST
TEST METHOD
PROCEDURE
REQUIREMENTS
MIL-STD-202F-method 304;
JIS C 5202-4.8
Temperature
At +25/–55 °C and +25/+125 °C
Refer to table 3
Coefficient of
Resistance
(T.C.R.)
Formula:
R2–R1
T.C.R= ------------------------- ×106 (ppm/°C)
R1(t2–t1)
Where
t1=+25 °C or specified room temperature
t2=–55 °C or +125 °C test temperature
R1=resistance at reference temperature in ohms
R2=resistance at test temperature in ohms
MIL-STD-202F-method 107G;
IEC 60115-1 4.19
Thermal Shock
At –65 (+0/–10) °C for 2 minutes and at +155
(+10/–0) °C for 2 minutes; 25 cycles
±(0.5%+0.05 Ω) for 1% tol.
±(1.0%+0.05 Ω) for 5% tol.
MIL-R-55342D-Para 4.7.4
Low
Temperature
Operation
At –65 (+0/–5) °C for 1 hour; RCWV applied
for 45 (+5/–0) minutes
±(0.5%+0.05 Ω) for 1% tol .
±(1.0%+0.05 Ω) for 5% tol.
No visible damage
MIL-R-55342D-Para 4.7.5;
IEC 60115-1 4.13
Short Time
Overload
2.5 × RCWV applied for 5 seconds at room
temperature
±(1.0%+0.05 Ω) for 1% tol.
±(2.0%+0.05 Ω) for 5% tol.
No visible damage
MIL-STD-202F-method 302;
IEC 60115-1 4.6.1.1
Insulation
Resistance
RCOV for 1 minute
≥10 GΩ
RC1218
Type
Voltage (DC)
500 V
MIL-STD-202F-method 301;
IEC 60115-1 4.6.1.1
Dielectric
Withstand
Voltage
Maximun voltage (Vrms) applied for 1 minute
No breakdown or flashover
RC1218
Type
Voltage (AC)
500 Vrms
MIL-STD-202F-method 210C;
IEC 60115-1 4.18
Resistance to
Soldering
Heat
Unmounted chips; 260 ±5 °C for 10 ±1
seconds
±(0.5%+0.05 Ω) for 1% tol.
±(1.0%+0.05 Ω) for 5% tol.
No visible damage
MIL-STD-202F-method 108A;
IEC 60115-1 4.25.1
Life
At 70±2 °C for 1,000 hours; RCWV applied for
1.5 hours on and 0.5 hour off
±(1%+0.05 Ω) for 1% tol.
±(3%+0.05 Ω) for 5% tol.
www.yageo.com
Oct 13, 2004 V.1
Product specification
8
10
SERIES
1218 (Pb Free)
RC
Chip Resistor Surface Mount
TEST
Solderability
TEST METHOD
PROCEDURE
Solder bath at 245±3 °C
REQUIREMENTS
MIL-STD-202F-method 208A;
IEC 60115-1 4.17
Well tinned (≥95% covered)
Dipping time: 2±0.5 seconds
No visible damage
JIS C 5202.6.14;
Bending
Strength
±(1.0%+0.05 Ω) for 1% tol.
±(1.0%+0.05 Ω) for 5% tol.
No visible damage
Resistors mounted on a 90 mm glass epoxy
resin PCB (FR4)
IEC 60115-1 4.15
Bending: 2 mm
MIL-STD-202F-method 215;
IEC 60115-1 4.29
Resistance to
Solvent
lsopropylalcohol (C3H7OH) or dichloromethane No smeared
(CH2Cl2) followed by brushing
JIS C 5202 5.9;
Noise
Maximum voltage (Vrms) applied.
Value
Resistors range
IEC 60115-1 4.12
R < 100 Ω
10 dB
24 dB
34 dB
44 dB
46 dB
48 dB
100 Ω ≤ R < 1 KΩ
1 KΩ ≤ R < 10 KΩ
10 KΩ ≤ R < 100 KΩ
100 KΩ ≤ R < 1 MΩ
1 MΩ ≤ R ≤ 22 MΩ
JIS C 5202 7.5;
Humidity
(steady state)
1,000 hours; 40±2 °C; 93(+2/–3)% RH
±(0.5%+0.05 Ω) for 1% tol.
±(2.0%+0.05 Ω) for 5% tol.
IEC 60115-8 4.24.8
RCWV applied for 1.5 hours on and 0.5 hour off
EIA/IS 4.13B;
Leaching
Solder bath at 260±5 °C
No visible damage
IEC 60115-8 4.18
Dipping time: 30±1 seconds
JIS C 5202 5.8
On request
Intermittent
Overload
At room temperature; 2.5 × RCWV applied for
1 second on and 25 seconds off; total 10,000
cycles
±(1.0%+0.05 Ω) for 1% tol.
±(2.0%+0.05 Ω) for 5% tol.
Resistance to
Vibration
On request
MIL-STD-202F-method 106F;
IEC 60115-1 4.24.2
Moisture
Resistance
Heat
42 cycles; total 1,000 hours
Shown as figure 9
±(0.5%+0.05Ω) for 1% tol.
±(2.0%+0.05Ω) for 5% tol.
No visible damage
www.yageo.com
Oct 13, 2004 V.1
Product specification
9
10
SERIES
1218 (Pb Free)
RC
Chip Resistor Surface Mount
80 − 98%
RH
80 − 98%
RH
75
90 − 98% RH
90 − 98% RH
90 − 98% RH
temperature
initial drying
24 hours
[°C]
rate of change of temperature is unspecified,
however, specimens shall not be subjected to
50
radiant heating from chamber conditioning processes
end of final cycle;
measurements
as specified in 2ꢀ7
+10 °C (+18 °F)
−2 °C (−3ꢀ6 °F)
25
0
initial measurements
as specified in 2ꢀ2
circulation of conditioning air shall be at a
minimum cubic rate per minute equivalent to
10 times the volume of the chamber
optional sub-cycle if specified
(2ꢀ3); sub-cycle performed during
any 5 of the first 9 cycles; humidity
uncontrolled during sub-cycle
temperature
tolerance
2 °C ( 3ꢀ6 °F)
unless otherwise
specified
voltage applied as specified in 2ꢀ4
STEP1
STEP2 STEP3
one cycle 24 hours; repeat as specified in 2ꢀ5
10 15
STEP4
STEP5 STEP6
STEP7
prior to first
cycle only
0
5
20
25
HBK073
time [h]
Fig. 9 Moisture resistance test requirements
www.yageo.com
Oct 13, 2004 V.1
Product specification
10
10
SERIES
1218 (Pb Free)
RC
Chip Resistor Surface Mount
REVISION HISTORY
REVISION DATE
CHANGE NOTIFICATION DESCRIPTION
Version 1 Oct 13, 2004
-
- New datasheet for 1218 thick film 1% and 5% with lead-free terminations
- Replace the 1218 part of pdf files: PRC201_51_17
- Test method and procedure updated
- Taping reel changed from 11" to 7" and quantity per reel from 5K to 4K as
well
www.yageo.com
Oct 13, 2004 V.1
相关型号：
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明