235002325234L [YAGEO]

Array/Network Resistor, Isolated, Metal Glaze/thick Film, 523000ohm, 50V, 1% +/-Tol, 200ppm/Cel, Surface Mount, 0408, CHIP, LEAD FREE;


型号：	235002325234L
厂家：	YAGEO CORPORATION
描述：	Array/Network Resistor, Isolated, Metal Glaze/thick Film, 523000ohm, 50V, 1% +/-Tol, 200ppm/Cel, Surface Mount, 0408, CHIP, LEAD FREE 电阻器
文件：	总8页 (文件大小：283K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

DATA SHEET

ARRAY CHIP RESISTORS

YC124 (8Pin/4R; Pb Free)

5%, 1%

sizes 4 × 0402

Product specification

SERIES

124 (Pb Free)

Chip Resistor Surface Mount

SCOPE

This specification describes YC124 series chip resistor arrays with lead-free terminations made by thick film

process.

ORDERING INFORMATION

Part number is identified by the series, size, tolerance, packing type, temperature coefficient, taping reel and

resistance value.

PHYCOMP ORDERING CODE

12NC CODE

CTC CODE

YC124 – X X X XX XXXX L

2350

(1)

XXX XXXXX L

( ) ( ) ( ) ( )

( )

(2)

(3)

PAPER / PE TAPE ON REEL (units) ⁽²⁾

( )

1 TOLERANCE

TYPE/ START TOL. RESISTANCE

4×0402 IN ⁽¹⁾

(%) RANGE

10,000

40,000

033 13xxx

023 8xxxx

F = ±1%

J = ±5%

ARV341

ARV342 2350

Jumper

2350

±5% 10 to 1 MΩ

±1% 10 to 1 MΩ

033 11xxx

023 2xxxx

033 91001

( )

2 PACKAGING TYPE

2350

0 Ω

R = Paper/PE taping reel

( )

3 TEMPERATURE COEFFICIENT

OF RESISTANCE

(1) The resistors have a 12-digit

ordering code starting with

2350.

Last digit of 12NC

Resistance decade ⁽³⁾

Last digit

– = Base on spec

0.01 to 0.0976

( )

4 TAPING REEL

(2) The subsequent 4 or 5 digits

indicate the resistor

0.1 to 0.976

07 = 7 inch dia. Reel

13 = 13 inch dia. Reel

1 to 9.76

tolerance and packaging.

10 to 97.6

100 to 976

1 to 9.76 k

(3) The remaining 4 or 3 digits

represent the resistance value

with the last digit indicating

the multiplier as shown in the

table of “Last digit of 12NC”.

( )

5 RESISTANCE VALUE

56R, 560R, 5K6, 56K, 1M

0R = Jumper

10 to 97.6 k

(6) RESISTOR TERMINATIONS

100 to 976 k

(4) “L” means lead-free

terminations.

1 to 9.76 M

L = Lead free terminations (pure Tin)

10 to 97.6 M

ORDERING EXAMPLE

Example: 0.02

0200 or 200

3007 or 307

1008 or 108

3303 or 333

1006 or 106

ORDERING EXAMPLE

The ordering code of an ARV341

convex chip resistor array, value

1,000 X with ±5% tolerance,

supplied in tape of 10,000 units

per reel is: 235003311102L.

0.3

The ordering code of a YC124

convex chip resistor array, value

1,000 X with ±5% tolerance,

supplied in 7-inch tape reel is:

33 k

10 M

YC124-JR-071KL.

NOTE

1. The “L” at the end of the code is only for ordering. On the reel label, the standard CTC or 12NC will be mentioned an additional stamp

“LFP”= lead free production.

2. Products with lead in terminations fulfil the same requirements as mentioned in this datasheet.

3. Products with lead in terminations will be phased out in the coming months (before July 1st, 2006)

www.yageo.com

Feb 04, 2005 V.1

Product specification

SERIES

124 (Pb Free)

Chip Resistor Surface Mount

MARKING

YC124

E-24 series: 3 digits

YNSC029

First two digits for significant figure and 3rd digit for number of zeros

Fig. 1 Value = 240 KΩ

For marking codes, please see EIA-marking code rules in data sheet “Chip resistors marking”.

CONSTRUCTION

The resistors are constructed out of

a high-grade ceramic body. Internal

protective coat

metal electrodes are added at each

resistor layer

end and connected by a resistive

inner electrode

paste. The composition of the paste

end termination

is adjusted to give the approximate

ceramic substrate YNSC053

required resistance and laser cutting

of this resistive layer that achieves

tolerance trims the value. The

resistive layer is covered with a

Fig. 2 Chip resistor construction

protective coat. Finally, the eight external terminations (pure Tin) are added. See fig. 2.

DIMENSIONS

Table 1

TYPE

YC124

B (mm)

H (mm)

P (mm)

L (mm)

H₂(mm)

0.20 ±0.15

0.45 ±0.05

0.50 ±0.05

2.00 ±0.10

0.30 ±0.15

0.45 ±0.10

0.30 ±0.15

1.00 ±0.10

CCB257_a

T (mm)

W₁(mm)

W₂(mm)

Fig. 3 YC124 series chip resistors dimension

For dimension see Table 1

SCHEMATIC

For dimension see Fig. 3 and Table 1

handbook, 2 columns

CCA862_b

Fig. 4 Equivalent circuit diagram

R1=R2=R3=R4

www.yageo.com

Feb 04, 2005 V.1

Product specification

SERIES

124 (Pb Free)

Chip Resistor Surface Mount

ELECTRICAL CHARACTERISTICS

FOOTPRINT AND SOLDERING

PROFILES

Table 2

For recommended footprint and

soldering profiles, please see the

special data sheet “Chip resistors

mounting”.

YC124 1/16 W

CHARACTERISTICS

Operating Temperature Range

Maximum Working Voltage

Maximum Overload Voltage

Dielectric Withstanding Voltage

Number of Resistors

–55 °C to +155 °C

50 V

100 V

ENVIRONMENTAL DATA

For material declaration

information (IMDS-data) of the

products, please see the

5% (E24) 10 Ω to 1 MΩ

Resistance Range

1% (E24/E96) 10 Ω to 1 MΩ

separated info “Environmental

data" conformed to EU RoHS.

Zero Ohm Jumper

< 0.05 Ω

±200 ppm/°C

1.0 A

Temperature Coefficient

Jumper Criteria

Rated Current

PACKING STYLE AND PACKAGING QUANTITY

Table 3 Packing style and packaging quantity

PRODUCT TYPE

YC124

PACKING STYLE

REEL DIMENSION

QUANTITY PER REEL

Paper / PE Taping Reel (R)

7" (178 mm)

13" (330 mm)

10,000 units

40,000 units

NOTE

1. For Paper/PE tape and reel specification/dimensions, please see the special data sheet “Packing” document.

FUNCTIONAL DESCRIPTION

POWER RATING

MRA632

max

YC124 rated power at 70°C is 1/16 W

(%P

)

rated

100

RATED VOLTAGE

The DC or AC (rms) continuous working voltage

corresponding to the rated power is determined by

the following formula:

V = √(P X R)

−55

50 70 100

155

(°C)

amb

Where

V = Continuous rated DC or

AC (rms) working voltage (V)

Fig. 5 Maximum dissipation (P ) in percentage of rated power

max

as a function of the operating ambient temperature (T

)

amb

P = Rated power (W)

R = Resistance value (X)

www.yageo.com

Feb 04, 2005 V.1

Product specification

SERIES

124 (Pb Free)

Chip Resistor Surface Mount

TESTS AND REQUIREMENTS

Table 4 Test condition, procedure and requirements

TEST

TEST METHOD

PROCEDURE

REQUIREMENTS

MIL-STD-202F-method 304;

JIS C 5202-4.8

Temperature

At +25/–55 °C and +25/+125 °C

Refer to table 2

Coefficient of

Resistance

(T.C.R.)

Formula:

R₂– R₁

T.C.R = ------------------------- × 10⁶(ppm/°C)

R₁(t₂– t₁)

Where

t₁= +25 °C or specified room temperature

t₂= –55 °C or +125 °C test temperature

R₁= resistance at reference temperature in ohms

R₂= resistance at test temperature in ohms

MIL-STD-202F-method 107G;

IEC 60115-1 4.19

Thermal Shock

At –65 (+0/–10) °C for 2 minutes and at +155

(+10/–0) °C for 2 minutes; 25 cycles

±(0.5% +0.05 Ω) for 1% tol.

±(1.0% +0.05 Ω) for 5% tol.

MIL-R-55342D-Para 4.7.4

Low

Temperature

Operation

At –65 (+0/–5) °C for 1 hour; RCWV applied for ±(0.5% +0.05 Ω) for 1% tol .

45 (+5/–0) minutes

±(1.0% +0.05 Ω) for 5% tol.

No visible damage

MIL-R-55342D-Para 4.7.5;

IEC 60115-1 4.13

Short Time

Overload

2.5 × RCWV applied for 5 seconds at room

temperature

±(1.0% +0.05 Ω) for 1% tol.

±(2.0% +0.05 Ω) for 5% tol.

No visible damage

MIL-STD-202F-method 302;

IEC 60115-1 4.6.1.1

Insulation

Resistance

RCOV for 1 minute

≥10 GΩ

YC124

Type

Voltage (DC)

100 V

MIL-STD-202F-method 301;

IEC 60115-1 4.6.1.1

Dielectric

Withstand

Voltage

Maximum voltage (V_rms) applied for 1 minute

No breakdown or flashover

YC124

Type

Voltage (AC)

100 V_rms

MIL-STD-202F-method 210C;

IEC 60115-1 4.18

Resistance to

Soldering

Heat

Unmounted chips; 260 ±5 °C for 10 ±1 seconds

±(0.5% +0.05 Ω) for 1% tol.

±(1.0% +0.05 Ω) for 5% tol.

No visible damage

MIL-STD-202F-method 108A;

IEC 60115-1 4.25.1

Life

At 70 ±2 °C for 1,000 hours; RCWV applied for

1.5 hours on and 0.5 hour off

±(1% +0.05 Ω) for 1% tol.

±(3% +0.05 Ω) for 5% tol.

www.yageo.com

Feb 04, 2005 V.1

Product specification

SERIES

124 (Pb Free)

Chip Resistor Surface Mount

TEST

Solderability

TEST METHOD

PROCEDURE

Solder bath at 245 ±3 °C

REQUIREMENTS

MIL-STD-202F-method 208A;

IEC 60115-1 4.17

Well tinned (≥95% covered)

Dipping time: 2 ±0.5 seconds

No visible damage

JIS C 5202.6.14;

Bending

Strength

±(1.0% +0.05 Ω) for 1% tol.

±(1.0% +0.05 Ω) for 5% tol.

No visible damage

Resistors mounted on a 90 mm glass epoxy

resin PCB (FR4)

IEC 60115-1 4.15

Bending: 1 mm

MIL-STD-202F-method 215;

IEC 60115-1 4.29

Resistance to

Solvent

lsopropylalcohol (C₃H₇OH) or dichloromethane No smeared

(CH₂Cl₂) followed by brushing

JIS C 5202 5.9;

Noise

Maximum voltage (V_rms) applied.

Value

Resistors range

IEC 60115-1 4.12

R < 100 Ω

10 dB

20 dB

30 dB

40 dB

46 dB

48 dB

100 Ω ≤ R < 1 KΩ

1 KΩ ≤ R < 10 KΩ

10 KΩ ≤ R < 100 KΩ

100 KΩ ≤ R < 1 MΩ

1 MΩ ≤ R ≤ 22 MΩ

JIS C 5202 7.5;

Humidity

(steady state)

1,000 hours; 40 ±2 °C; 93(+2/–3)% RH

±(0.5% +0.05 Ω) for 1% tol.

±(2.0% +0.05 Ω) for 5% tol.

IEC 60115-8 4.24.8

RCWV applied for 1.5 hours on and 0.5 hour off

EIA/IS 4.13B;

Leaching

Solder bath at 260 ±5 °C

No visible damage

IEC 60115-8 4.18

Dipping time: 30 ±1 seconds

JIS C 5202 5.8

On request

Intermittent

Overload

At room temperature; 2.5 × RCWV applied for

1 second on and 25 seconds off; total 10,000

cycles

±(1.0% +0.05 Ω) for 1% tol.

±(2.0% +0.05 Ω) for 5% tol.

Resistance to

Vibration

On request

MIL-STD-202F-method 106F;

IEC 60115-1 4.24.2

Moisture

Resistance

Heat

42 cycles; total 1,000 hours

Shown as Fig. 6

±(0.5% +0.05Ω) for 1% tol.

±(2.0% +0.05Ω) for 5% tol.

No visible damage

www.yageo.com

Feb 04, 2005 V.1

Product specification

SERIES

124 (Pb Free)

Chip Resistor Surface Mount

80 − 98%

90 − 98% RH

temperature

initial drying

24 hours

[°C]

rate of change of temperature is unspecified,

however, specimens shall not be subjected to

radiant heating from chamber conditioning processes

end of final cycle;

measurements

as specified in 2ꢀ7

+10 °C (+18 °F)

−2 °C (−3ꢀ6 °F)

initial measurements

as specified in 2ꢀ2

circulation of conditioning air shall be at a

minimum cubic rate per minute equivalent to

10 times the volume of the chamber

optional sub-cycle if specified

(2ꢀ3); sub-cycle performed during

any 5 of the first 9 cycles; humidity

uncontrolled during sub-cycle

temperature

tolerance

2 °C ( 3ꢀ6 °F)

unless otherwise

specified

voltage applied as specified in 2ꢀ4

STEP1

STEP2 STEP3

one cycle 24 hours; repeat as specified in 2ꢀ5

10 15

STEP4

STEP5 STEP6

STEP7

prior to first

cycle only

HBK073

time [h]

Fig. 6 Moisture resistance test requirements

www.yageo.com

Feb 04, 2005 V.1

Product specification

SERIES

124 (Pb Free)

Chip Resistor Surface Mount

REVISION HISTORY

REVISION DATE

CHANGE NOTIFICATION DESCRIPTION

Version 1

Feb 04, 2005

- New datasheet for 4 × 0402 chip resistor arrays 1% and 5% with lead-

free terminations

- Replace the 4 × 0402 part of pdf files: ARV341_5_PbFree_L_0.pdf and

ARV342_1_PbFree_L_0.pdf

- Test method and procedure updated

Version 0

Dec 05, 2003

www.yageo.com

Feb 04, 2005 V.1

235002325234L [YAGEO]

相关型号：

SI9130DB

SI9135LG-T1

SI9135LG-T1-E3

SI9135_11

SI9136_11

SI9130CG-T1-E3

SI9130LG-T1-E3

SI9130_11

SI9137

SI9137DB

SI9137LG

SI9122E