首页 |元器件品牌

RC0402JR-10680KL [YAGEO]

GENERAL PURPOSE CHIP RESISTORS; 通用贴片电阻
RC0402JR-10680KL
型号： RC0402JR-10680KL
厂家： YAGEO CORPORATION    YAGEO CORPORATION
描述：

GENERAL PURPOSE CHIP RESISTORS
通用贴片电阻
文件： 总9页 (文件大小：309K)
中文：  中文翻译
下载：  下载PDF数据表文档文件
 查看货源
DATA SHEET  
GENERAL PURPOSE CHIP RESISTORS  
RC0402  
5%, 1%  
RoHS compliant & Halogen Free  
Product specification  
2
9
SERIES  
0402  
RC  
Chip Resistor Surface Mount  
SCOPE  
ORDERING INFORMATION - GLOBAL PART NUMBER & 12NC  
This specification describes  
RC0402 series chip resistors  
with lead-free terminations made  
by thick film process.  
Both part numbers are identified by the series, size, tolerance, packing  
type, temperature coefficient, taping reel and resistance value.  
YAGEO BRAND ordering code  
(
)
GLOBAL PART NUMBER PREFERRED  
RC0402 X R - XX XXXX L  
APPLICATIONS  
( ) ( ) ( ) ( )  
( )  
5
( )  
6
1
2
3
4
ꢀ All general purpose application  
( )  
1 TOLERANCE  
F = ±1%  
FEATURES  
J = ±5% (for Jumper ordering, use code of J)  
ꢀ Halogen Free Epoxy  
( )  
2 PACKAGING TYPE  
ꢀ RoHS compliant  
R = Paper / PE taping reel  
- Products with lead free  
terminations meet RoHS  
requirements  
( )  
3 TEMPERATURE COEFFICIENT OF RESISTANCE  
– = Base on spec  
- Pb-glass contained in electrodes,  
resistor element and glass are  
exempted by RoHS  
( )  
4 TAPING REEL  
07 = 7 inch dia. Reel  
ꢀ Reducing environmentally  
7D = 7 inch dia. Reel, 2 x Standard Quantity  
10 = 10 inch dia. Reel  
hazardous wastes  
ꢀ High component and equipment  
13 = 13 inch dia. Reel  
reliability  
( )  
5 RESISTANCE VALUE  
ꢀ Saving of PCB space  
There are 2~4 digits indicated the resistance value. Letter R/K/M is decimal point, no  
need to mention the last zero after R/K/M, e.g.1K2, not 1K20.  
ꢀ None forbidden-materials used  
in products/production  
Detailed resistance rules show in table of “Resistance rule of global part number”.  
(6) DEFAULT CODE  
Letter L is system default code for ordering only (Note)  
Resistance rule of global part  
number  
ORDERING EXAMPLE  
The ordering code of a RC0402  
chip resistor, value 56 X with  
Resistance code rule  
Example  
D1  
0R  
D1 = Dummy  
0R = Jumper  
±1% tolerance, supplied in 7-inch  
tape of 20,000 units per reel is:  
RC0402FR-7D56RL.  
1R = 1 Ω  
1R5 = 1.5 Ω  
9R76 = 9.76 Ω  
XRXX  
(1 to 9.76 Ω)  
NOTE  
1. All our RSMD products meet RoHS  
compliant and Halogen Free. "LFP" of  
the internal 2D reel label mentions  
"Lead Free Process"  
XXRX  
(10 to 97.6 Ω)  
10R = 10 Ω  
97R6 = 97.6 Ω  
XXXR  
(100 to 976 Ω)  
100R = 100 Ω  
2. On customized label, "LFP" or specific  
symbol can be printed  
XKXX  
1K = 1,000 Ω  
(1 to 9.76 KΩ)  
9K76 = 9760 Ω  
XMXX  
1M = 1,000,000 Ω  
(1 to 9.76 MΩ)  
9M76= 9,760,000 Ω  
www.yageo.com  
Jan 05, 2011 V.6  
Product specification  
3
9
SERIES  
0402  
RC  
Chip Resistor Surface Mount  
PHYCOMP BRAND ordering codes  
Both GLOBAL PART NUMBER (preferred) and 12NC (traditional) codes are acceptable to order Phycomp  
brand products.  
(
)
GLOBAL PART NUMBER PREFERRED  
For detailed information of GLOBAL PART NUMBER and ordering example, please refer to page 2.  
12NC CODE  
2322  
(1)  
XXX XXXXX L  
Last digit of 12NC  
Resistance decade (3)  
( )  
(2)  
(3)  
4
Last digit  
PAPER / PE TAPE ON REEL (units) (2)  
X
0.01 to 0.0976  
TYPE/ START TOL. RESISTANCE  
0402 IN (1)  
(%) RANGE  
0
7
8
9
1
2
3
4
5
6
10,000  
20,000/not preferred  
50,000  
705 87xxx  
706 8xxxx  
705 91007  
X
0.1 to 0.976  
X
1 to 9.76  
RC31  
2322  
±5% 1 to 22 MΩ  
±1% 1 to 10 MΩ  
705 70xxx  
706 7xxxx  
705 91001  
---  
---  
---  
X
10 to 97.6  
100 to 976  
1 to 9.76 K  
RC32 2322  
Jumper 2322  
X
-
0 Ω  
X
(1) The resistors have a 12-digit ordering code starting with 2322.  
X
10 to 97.6 K  
(2) The subsequent 4 or 5 digits indicate the resistor tolerance and  
packaging.  
X
100 to 976 K  
X
1 to 9.76 M  
(3) The remaining 4 or 3 digits represent the resistance value with the  
last digit indicating the multiplier as shown in the table of  
“Last digit of 12NC”.  
X
10 to 97.6 M  
X
X
Example: 0.02  
=
=
=
=
=
0200 or 200  
3007 or 307  
1008 or 108  
3303 or 333  
1006 or 106  
(4) Letter L is system default code for order only (Note)  
X
0.3  
X
1
ORDERING EXAMPLE  
33 K  
10 M  
The ordering code of a RC32 resistor, value 56 X with ±1% tolerance,  
supplied in tape of 10,000 units per reel is: 232270675609L or  
RC0402FR-0756RL.  
X
NOTE  
1. All our RSMD products meet RoHS compliant and Halogen Free. "LFP" of the internal 2D reel label mentions "Lead Free Process"  
2. On customized label, "LFP" or specific symbol can be printed  
www.yageo.com  
Jan 05, 2011 V.6  
Product specification  
4
9
SERIES  
0402  
RC  
Chip Resistor Surface Mount  
MARKING  
RC0402  
No marking  
ynsc007  
Fig. 1  
For further marking information, please see special data sheet “Chip resistors marking”  
CONSTRUCTION  
The resistor is constructed on top  
of a high-grade ceramic body.  
OUTLINES  
For dimension see Table 1  
Internal metal electrodes are added  
on each end to make the contacts to  
the thick film resistive element. The  
composition of the resistive element  
is a noble metal imbedded into a  
glass and covered by a second glass  
to prevent environment influences.  
The resistor is laser trimmed to the  
rated resistance value. The resistor  
is covered with a protective epoxy  
coat, finally the two external  
overcoat  
Primary glass layer  
resistive layer  
(Jumper chip is a conductor)  
inner electrode  
H
termination(Ni/matte tin)  
ceramic substrate  
I
2
overcoat  
I
1
terminations (matte tin on Ni-  
barrier) are added. See fig.2  
W
YNSC056  
L
DIMENSIONS  
Table 1  
TYPE  
RC0402  
Fig. 2 Chip resistor outlines  
L (mm)  
W (mm)  
H (mm)  
I1 (mm)  
I2 (mm)  
1.00 ±0.05  
0.50 ±0.05  
0.35 ±0.05  
0.20 ±0.10  
0.25 ±0.10  
www.yageo.com  
Jan 05, 2011 V.6  
Product specification  
5
9
SERIES  
0402  
RC  
Chip Resistor Surface Mount  
ELECTRICAL CHARACTERISTICS  
FOOTPRINT AND SOLDERING  
PROFILES  
Table 2  
For recommended footprint and  
soldering profiles, please see the  
special data sheet “Chip resistors  
mounting”.  
RC0402 1/16 W  
CHARACTERISTICS  
Operating Temperature Range  
Maximum Working Voltage  
Maximum Overload Voltage  
Dielectric Withstanding Voltage  
–55 °C to +155 °C  
50 V  
100 V  
100 V  
5% (E24) 1 Ω to 22 MΩ  
Resistance Range  
1% (E24/E96) 1 Ω to 10 MΩ  
Zero Ohm Jumper < 0.05 Ω  
1 Ω ≤ R ≤ 10 Ω  
±200 ppm/°C  
±100 ppm/°C  
±200 ppm/°C  
1.0 A  
Temperature Coefficient  
Jumper Criteria  
10 Ω < R ≤ 10 MΩ  
10 MΩ < R ≤ 22 MΩ  
Rated Current  
Maximum Current  
2.0 A  
PACKING STYLE AND PACKAGING QUANTITY  
Table 3 Packing style and packaging quantity  
PRODUCT TYPE  
RC0402  
PACKING STYLE  
REEL DIMENSION  
QUANTITY PER REEL  
Paper / PE Taping Reel (R)  
7" (178 mm)  
10" (254 mm)  
13" (330 mm)  
10,000/20,000 units  
20,000 units  
50,000 units  
NOTE  
1. For paper/PE tape and reel specification/dimensions, please see the special data sheet “Chip resistors packing”  
2. For size of 0402, standard quantity is 10,000 units per reel  
FUNCTIONAL DESCRIPTION  
POWER RATING  
handbook, halfpage  
RC0402 rated power at 70°C is 1/16 W  
P
MLB206_2  
(%P  
rated  
)
RATED VOLTAGE  
100  
50  
0
The DC or AC (rms) continuous working voltage  
corresponding to the rated power is determined by  
the following formula:  
V=√(P X R)  
55  
0
50 70  
100  
155  
o
(
C)  
T
amb  
or max. working voltage whichever is less  
Where  
Fig. 3 Maximum dissipation (P) in percentage of rated power as a  
function of the operating ambient temperature (T  
V=Continuous rated DC or  
AC (rms) working voltage (V)  
)
amb  
P=Rated power (W)  
R=Resistance value (X)  
www.yageo.com  
Jan 05, 2011 V.6  
Product specification  
6
9
SERIES  
0402  
RC  
Chip Resistor Surface Mount  
TESTS AND REQUIREMENTS  
Table 4 Test condition, procedure and requirements  
TEST  
TEST METHOD  
IEC 60115-1 4.8  
PROCEDURE  
REQUIREMENTS  
Refer to table 2  
Temperature  
Coefficient of  
Resistance  
(T.C.R.)  
At +25/–55 °C and +25/+125 °C  
Formula:  
R2–R1  
T.C.R= ------------------------- ×106 (ppm/°C)  
R1(t2–t1)  
Where  
t1=+25 °C or specified room temperature  
t2=–55 °C or +125 °C test temperature  
R1=resistance at reference temperature in ohms  
R2=resistance at test temperature in ohms  
IEC 60115-1 4.25.1  
IEC 60068-2-2  
Life/Endurance  
At 70±5 °C for 1,000 hours, RCWV applied for  
1.5 hours on, 0.5 hour off, still air required  
±(1.0%+0.05 Ω) for 1% tol.  
±(3.0%+0.05 Ω) for 5% tol.  
<100 mΩ for Jumper  
High  
Temperature  
Exposure/  
Endurance at  
Upper Category  
Temperature  
1,000 hours at 155±5 °C, unpowered  
±(1.0%+0.05 Ω) for 1% tol.  
±(2.0%+0.05 Ω) for 5% tol.  
<50 mΩ for Jumper  
MIL-STD-202G Method-106G  
Moisture  
Resistance  
Each temperature / humidity cycle is defined at 8  
hours, 3 cycles / 24 hours for 10d. with 25 °C /  
65 °C 95% R.H, without steps 7a & 7b,  
unpowered  
±(0.5%+0.05 Ω) for 1% tol.  
±(2.0%+0.05 Ω) for 5% tol.  
<100 mΩ for Jumper  
Parts mounted on test-boards, without  
condensation on parts  
Measurement at 24±2 hours after test conclusion  
MIL-STD-202G Method-107G  
Thermal Shock  
-55/+125 °C  
±(0.5%+0.05 Ω) for 1% tol.  
±(1%+0.05 Ω) for 5% tol.  
<50 mΩ for Jumper  
Number of cycles required is 300. Devices  
unmounted  
Maximum transfer time is 20 seconds. Dwell time  
is 15 minutes. Air – Air  
IEC60115-1 4.13  
Short Time  
Overload  
2.5 times of rated voltage or maximum overload  
voltage whichever is less for 5 sec at room  
temperature  
±(1.0%+0.05 Ω) for 1% tol.  
±(2.0%+0.05 Ω) for 5% tol.  
<50 mΩ for Jumper  
No visible damage  
www.yageo.com  
Jan 05, 2011 V.6  
Product specification  
7
9
SERIES  
0402  
RC  
Chip Resistor Surface Mount  
TEST  
TEST METHOD  
IEC 60068-2-21  
PROCEDURE  
REQUIREMENTS  
Board Flex/  
Bending  
Chips mounted on a 90mm glass epoxy resin  
PCB (FR4)  
±(1.0%+0.05 Ω) for 1%, 5% tol.  
<50 mΩ for Jumper  
5 mm bending  
No visible damage  
Bending time: 60±5 seconds  
IEC 60068-2-1  
Low  
Temperature  
Operation  
The resistor shall be subjected to a DC rated  
voltage for 1.5 h-on, 0.5 h-off, at -55±3 °C  
±(0.5%+0.05 Ω) for 1% tol.  
±(1.0%+0.05 Ω) for 5% tol.  
No visible damage  
This constitutes shall be repeated for 96 hours  
However the applied voltage shall not exceed  
the maximum operating voltage  
IEC 60115-1 4.6  
IEC 60115-1 4.7  
Insulation  
Resistance  
Rated continuous overload voltage (RCOV)  
for 1 minute  
≥10 GΩ  
RC0402  
Type  
Voltage (DC)  
100 V  
Dielectric  
Withstand  
Voltage  
Maximum voltage (Vrms) applied for 1 minute  
No breakdown or flashover  
RC0402  
Type  
Voltage (AC)  
100 Vrms  
IPC/JEDEC J-STD-020D  
IEC 60115-1 4.12  
Resistance to  
Solvent  
lsopropylalcohol (C3H7OH) followed by  
brushing  
No smeared  
Noise  
Maximum voltage (Vrms) applied  
Value  
Resistors range  
R < 100 Ω  
10 dB  
20 dB  
30 dB  
40 dB  
46 dB  
48 dB  
100 Ω ≤ R < 1 KΩ  
1 KΩ ≤ R < 10 KΩ  
10 KΩ ≤ R < 100 KΩ  
100 KΩ ≤ R < 1 MΩ  
1 MΩ ≤ R ≤ 22 MΩ  
IEC 60115-1 4.21  
Humidity  
Steady state for 1000 hours at 40 °C / 95% R.H.  
RCWV applied for 1.5 hours on and  
0.5 hour off  
±(1.0%+0.05 Ω) for 1% tol.  
±(2.0%+0.05 Ω) for 5% tol.  
<100 mΩ for Jumper  
www.yageo.com  
Jan 05, 2011 V.6  
Product specification  
8
9
SERIES  
0402  
RC  
Chip Resistor Surface Mount  
TEST  
TEST METHOD  
IEC 60115-1 4.39  
PROCEDURE  
REQUIREMENTS  
Intermittent  
Overload  
2.5 times of rated voltage or maximum  
overload voltage whichever is less for 1 second  
on and 25 seconds off; total 10,000 cycles  
±(1.0%+0.05 Ω) for 1% tol.  
±(2.0%+0.05 Ω) for 5% tol.  
<100 mΩ for Jumper  
Solderability  
- Wetting  
Well tinned (≥95% covered)  
IPC/JEDEC J-STD-002B test B  
Electrical Test not required  
Magnification 50X  
No visible damage  
SMD conditions:  
1st step: method B, aging 4 hours at 155 °C  
dry heat  
2nd step: lead-free solder bath at 245±3 °C  
Dipping time: 3±0.5 seconds  
IPC/JEDEC J-STD-002B test D  
- Leaching  
Lead-free solder, 260 °C, 30 seconds  
immersion time  
No visible damage  
IEC 60068-2-58  
- Resistance to  
Soldering Heat  
Condition B, no pre-heat of samples  
±(0.5%+0.05 Ω) for 1% tol.  
±(1.0%+0.05 Ω) for 5% tol.  
<50 mΩ for Jumper  
Lead-free solder, 260 °C, 10 seconds  
immersion time  
Procedure 2 for SMD: devices fluxed and  
cleaned with isopropanol  
No visible damage  
www.yageo.com  
Jan 05, 2011 V.6  
Product specification  
9
9
SERIES  
0402  
RC  
Chip Resistor Surface Mount  
REVISION HISTORY  
REVISION DATE  
CHANGE NOTIFICATION DESCRIPTION  
Version 6  
Version 5  
Jan 05, 2011  
Apr 27, 2010  
-
-
- Typo updated  
- Updated test items and methods  
- Add new taping reel code of 7 inch dia. reel with double standard  
quantity (20,000 units per reel)  
Version 4  
Version 3  
Jul 21, 2009  
Jul 15, 2008  
-
-
- Test items and methods updated  
- Test requirements upgraded  
- Change to dual brand datasheet that describe RC0402 with RoHS  
compliant  
- Description of "Halogen Free Epoxy" added  
- Define global part number  
Version 2  
Sep 03, 2004  
-
- New datasheet for 0402 thick film 1% and 5% with lead-free terminations  
- Replace the 0402 part of pdf files: RC01_11_21_31_5,  
RC02_12_22_32_10  
- Test method and procedure updated  
- PE tape added (paper tape will be replaced by PE tape)  
“ Yageo reserves all the rights for revising the content of this datasheet without further notification, as long as the products itself are unchanged. Any  
product change will be announced by PCN.”  
www.yageo.com  
Jan 05, 2011 V.6  

相关型号：

SI9130DB

 5- and 3.3-V Step-Down Synchronous Converters

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135LG-T1

 SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135LG-T1-E3

 SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9135_11

 SMBus Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9136_11

 Multi-Output Power-Supply Controller

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130CG-T1-E3

 Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130LG-T1-E3

 Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9130_11

 Pin-Programmable Dual Controller - Portable PCs

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137

 Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137DB

 Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9137LG

 Multi-Output, Sequence Selectable Power-Supply Controller for Mobile Applications

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY

SI9122E

 500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification Drivers

Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明