RE0402BRE07156KL [YAGEO]
Fixed Resistor, Metal Glaze/thick Film, 0.0625W, 156000ohm, 50V, 0.1% +/-Tol, 50ppm/Cel, Surface Mount, 0402, CHIP, HALOGEN FREE AND ROHS COMPLIANT;型号: | RE0402BRE07156KL |
厂家: | YAGEO CORPORATION |
描述: | Fixed Resistor, Metal Glaze/thick Film, 0.0625W, 156000ohm, 50V, 0.1% +/-Tol, 50ppm/Cel, Surface Mount, 0402, CHIP, HALOGEN FREE AND ROHS COMPLIANT |
文件: | 总7页 (文件大小:490K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
THICK FILM CHIP RESISTORS
Precision grade
RE series
0.1%, 0.5%, 1%, TC 50
sizes 0201/0402/0603/0805/1206
RoHS compliant & Halogen Free
Product specification
2
7
SERIES
0201 to 1206
RE
Chip Resistor Surface Mount
SCOPE
ORDERING INFORMATION - GLOBAL PART NUMBER & 12NC
This specification describes
RE0201 to RE1206 ultra precision
chip resistors with lead-free
terminations made by thick film
process.
Both part numbers are identified by the series, size, tolerance, packing
type, temperature coefficient, taping reel and resistance value.
YAGEO BRAND ordering code
GLOBAL PART NUMBER (PREFERRED)
RE XXXX X X X XX XXXX L
( )
( ) ( ) ( ) ( )
( )
6
( )
7
1
2
3
4
5
APPLICATIONS
Converters
( )
1 SIZE
Printer equipment
Server board
Telecom
0201 / 0402 / 0603 / 0805 / 1206
( )
2 TOLERANCE
B = ±0.1%
D = ±0.5%
F = ±1%
Consumer
FEATURES
Halogen Free Epoxy
( )
3 PACKAGING TYPE
R = Paper/PE taping reel
RoHS compliant
Reducing environmentally
hazardous wastes
( )
4 TEMPERATURE COEFFICIENT OF RESISTANCE
E = ±50 ppm/°C
High component and equipment
reliability
( )
5 TAPING REEL
Non-forbidden material used in
products/production
07 = 7 inch dia. Reel
13 = 13 inch dia. Reel
Moisture sensitivity level: MSL 1
( )
6 RESISTANCE VALUE
There are 2~4 digits indicated the resistor value. Letter R/K/M is decimal point, no need
to mention the last zero after R/K/M, e.g.1K2, not 1K20.
Detailed resistance rules show in table of “Resistance rule of global part number”.
(7) DEFAULT CODE
Letter L is system default code for order only (Note)
ORDERING EXAMPLE
Resistance rule of global part
number
The ordering code of a RE0603
Resistance code rule
Example
chip resistor, TC 50 value 56Ω with
±0.5% tolerance, supplied in 7-inch
tape reel is: RE0603DRE0756RL.
XXRX
10R = 10 Ω
(10 to 97.6 Ω)
97R6 = 97.6 Ω
XXXR
(100 to 976 Ω)
100R = 100 Ω
NOTE
1. All our R-Chip products meet RoHS
compliant and Halogen Free. "LFP" of
the internal 2D reel label mentions
"Lead Free Process"
XKXX
(1 to 9.76 KΩ)
1K = 1,000 Ω
9K76 = 9760 Ω
XMXX
(1 MΩ)
1M = 1,000,000 Ω
2. On customized label, "LFP" or specific
symbol can be printed
www.yageo.com
Jan. 23, 2014 V.1
Product specification
3
7
SERIES
0201 to 1206
RE
Chip Resistor Surface Mount
MARKING
RE0805 / RE1206
Either resistance in E-24 or E-96: 4 digits
First three digits for significant figure and 4th digit for number of zeros
Fig. 1 Value = 10 kΩ
RE0603
E-24 series: 3 digits
First two digits for significant figure and 3rd digit for number of zeros
Fig. 2 Value = 12 kΩ
E-96 series: 3 digits for 0603±1% EIA-96 marking method
Fig. 3 Value = 12.4 kΩ
RE0201/0402
No marking
Fig. 4
For further marking information, please see special data sheet “Chip resistors marking”.
CONSTRUCTION
The resistors are constructed out of a high-grade ceramic
body. Internal metal electrodes are added at each end and
connected by a resistive layer. The resistive layer is adjusted
OUTLINES
For dimension see Table 1
to give the approximate required resistance and laser cutting
of this resistive layer that achieves tolerance trims the value.
The resistive layer is covered with a protective coat and
printed with the resistance value. Finally, the two external
marking layer
protective coat
resistive layer
inner electrode
terminations (matte tin) are added. See fig. 5.
H
termination (Ni/matte tin)
ceramic substrate
I
2
DIMENSION
I
1
Table 1 For outlines see fig. 5
TYPE
L (mm) W (mm) H (mm) I1 (mm) I2 (mm)
RE0201
RE0402
RE0603
RE0805
RE1206
0.60 ±0.03 0.30 ±0.03 0.23 ±0.03 0.10 ±0.05 0.15 ±0.05
1.00 ±0.05 0.50 ±0.05 0.32 ±0.05 0.20 ±0.10 0.25 ±0.10
1.60 ±0.10 0.80 ±0.10 0.45 ±0.10 0.25 ±0.15 0.25 ±0.15
2.00 ±0.10 1.25 ±0.10 0.50 ±0.10 0.35 ±0.20 0.35 ±0.20
3.10 ±0.10 1.60 ±0.10 0.55 ±0.10 0.45 ±0.20 0.40 ±0.20
W
YNSC064
L
Fig. 5 Chip resistor outlines
www.yageo.com
Jan. 23, 2014 V.1
Product specification
4
7
SERIES
0201 to 1206
RE
Chip Resistor Surface Mount
ELECTRICAL CHARACTERISTICS
Table 2
MAXIMUM
WORKING
VOLTAGE
DIELECTRIC
WITHSTAND OVERLOAD
MAXIMUM
TEMPERATURE
COEFFICIENT OF
RESISTANCE
POWER
RESISTANCE
RANGE
OPERATING
TEMPERATURE RANGE
TYPE
RATING
VOLTAGE
50 V
VOLTAGE
50 V
RE0201
RE0402
RE0603
RE0805
RE1206
10 Ω to 1 MΩ
10 Ω to 1 MΩ
10 Ω to 1 MΩ
10 Ω to 1 MΩ
10 Ω to 1 MΩ
–55 °C to +155 °C
–55 °C to +155 °C
–55 °C to +155 °C
–55 °C to +155 °C
–55 °C to +155 °C
1/20W
1/16 W
1/10 W
1/8 W
25 V
50 V
±50 ppm/°C
±50 ppm/°C
±50 ppm/°C
±50 ppm/°C
±50 ppm/°C
100 V
100 V
300 V
500 V
100 V
100 V
300 V
400 V
50 V
150 V
200 V
1/4 W
NOTE
The maximum working voltage that may be continuously applied to the resistor element, see “IEC publication 60115-8”
FOOTPRINT AND SOLDERING PROFILES
For recommended footprint and soldering profiles, please see the special data sheet “Chip resistors mounting”.
PACKING STYLE AND PACKAGING QUANTITY
Table 3 Packing style and packaging quantity
PACKING STYLE
REEL DIMENSION
7" (178 mm)
RE0201
10,000
50,000
RE0402
10,000
50,000
RE0603
5,000
RE0805
5,000
RE1206
5,000
Paper/PE taping reel (R)
13" (330 mm)
20,000
20,000
20,000
NOTE
1. For Paper/PE tape and reel specification/dimensions, please see the special data sheet “Chip resistors packing”
FUNCTIONAL DESCRIPTION
POWER RATING
Each type rated power at 70°C:
RE0201=1/20W, RE0402=1/16W, RE0603=1/10W,
RE0805=1/8 W, RE1206=1/4W
RATED VOLTAGE
The DC or AC (rms) continuous working voltage
corresponding to the rated power is determined by
the following formula:
V=√(P X R)
or max. working voltage whichever is less
Fig. 6 Maximum dissipation (P) in percentage of rated power as a
function of the operating ambient temperature (T
)
amb
Where
V=Continuous rated DC or
AC (rms) working voltage (V)
P=Rated power (W)
R=Resistance value (Ω )
www.yageo.com
Jan. 23, 2014 V.1
Product specification
5
7
SERIES
0201 to 1206
RE
Chip Resistor Surface Mount
TESTS AND REQUIREMENTS
Table 4 Test condition, procedure and requirements
TEST
TEST METHOD
IEC 60115-1 4.25.1
PROCEDURE
REQUIREMENTS
At 70±5 °C for 1,000 hours, RCWV applied for ±(3%+0.05 Ω)
Life/Endurance
1.5 hours on, 0.5 hour off, still air required
IEC 60068-2-2
1,000 hours at 155±5 °C, unpowered
±(3%+0.05 Ω)
High
Temperature
Exposure/
Endurance at
Upper Category
Temperature
MIL-STD-202G Method-106G
Each temperature / humidity cycle is defined at 8
hours, 3 cycles / 24 hours for 10d. with 25 °C /
65 °C 95% R.H, without steps 7a & 7b,
unpowered
±(3%+0.05 Ω)
Moisture
Resistance
Parts mounted on test-boards, without
condensation on parts
Measurement at 24±2 hours after
test conclusion
MIL-STD-202G Method-107G
-55/+125 °C
±(1%+0.05 Ω)
Thermal Shock
Number of cycles required is 300.
Maximum transfer time is 20 seconds. Dwell time
is 15 minutes. Air – Air
IEC60115-1 4.13
IEC 60068-2-21
2.5 times of rated voltage or maximum overload
voltage whichever is less for 5 sec at room
temperature
±(1%+0.05 Ω)
Short Time
Overload
No visible damage
Chips mounted on a 90mm glass epoxy resin
PCB (FR4)
±(1%+0.05 Ω)
Board Flex/
Bending
No visible damage
Bending: see table 5 for each size
Bending time: 60±5 seconds
www.yageo.com
Jan. 23, 2014 V.1
Product specification
6
7
SERIES
0201 to 1206
RE
Chip Resistor Surface Mount
TEST
TEST METHOD
IEC 60115-1 4.21
PROCEDURE
REQUIREMENTS
±(3%+0.05 Ω )
Steady state for 1000 hours at 40 °C / 95%
R.H. RCWV applied for 1.5 hours on and 0.5
hour off
Humidity
Solderability
- Wetting
Electrical Test not required
Magnification 50X
IPC/JEDEC J-STD-002B test B
Well tinned (≥95% covered)
No visible damage
SMD conditions:
1st step: method B, aging 4 hours at 155°C
dry heat
2nd step: leadfree solder bath at 245±3°C
Dipping time: 3±0.5 seconds
IPC/JEDEC J-STD-002B test D
IEC 60068-2-58
Leadfree solder, 260 °C, 30 seconds
immersion time
No visible damage
- Leaching
Condition B, no pre-heat of samples.
Leadfree solder, 260 °C, 10 seconds
immersion time
±(1%+0.05 Ω)
- Resistance to
Soldering Heat
No visible damage
Procedure 2 for SMD: devices fluxed and
cleaned with isopropanol
Table 5 Bending for sizes 0201 to 1206
TYPE
RE0201
RE0402
RE0603
RE0805
RE1206
Specification (mm)
5
5
3
3
2
www.yageo.com
Jan. 23, 2014 V.1
Product specification
7
7
SERIES
0201 to 1206
RE
Chip Resistor Surface Mount
REVISION HISTORY
REVISION DATE
CHANGE NOTIFICATION
DESCRIPTION
- Add RE0201
- Add 0.1%
Version 1
Jan 23, 2014
-
- Update TEST AND REQUIREMENTS, add Humidity test
Version 0
Dec 10, 2010 -
- New datasheet for thick film ultra precision chip resistors sizes of
0402/0603/0805/1206, 0.5%, 1%, TC50 with lead-free terminations
“ Yageo reserves all the rights for revising the content of this datasheet without further notification, as long as the products itself are unchanged. Any
product change will be announced by PCN.”
www.yageo.com
Jan. 23, 2014 V.1
相关型号:
SI9130DB
5- and 3.3-V Step-Down Synchronous ConvertersWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135LG-T1-E3
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9135_11
SMBus Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9136_11
Multi-Output Power-Supply ControllerWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130CG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130LG-T1-E3
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9130_11
Pin-Programmable Dual Controller - Portable PCsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137DB
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9137LG
Multi-Output, Sequence Selectable Power-Supply Controller for Mobile ApplicationsWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
SI9122E
500-kHz Half-Bridge DC/DC Controller with Integrated Secondary Synchronous Rectification DriversWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
VISHAY
©2020 ICPDF网 联系我们和版权申明