ZL40167/DCA [ZARLINK]
Operational Amplifier, 2 Func, 4200uV Offset-Max, PDSO8, 0.150 INCH, MS-012AA, SOIC-8;型号: | ZL40167/DCA |
厂家: | ZARLINK SEMICONDUCTOR INC |
描述: | Operational Amplifier, 2 Func, 4200uV Offset-Max, PDSO8, 0.150 INCH, MS-012AA, SOIC-8 放大器 光电二极管 |
文件: | 总32页 (文件大小:773K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
ZL40167
High Output Current
High Speed Dual Operational Amplifier
Data Sheet
September 2003
Features
•
High Output Drive
Ordering Information
•
•
18.8 Vpp differential output voltage, RL = 50Ω
9.4 Vpp single-ended output voltage, RL = 25Ω
ZL40167/DCA (tubes) 8 lead SOIC
ZL40167/DCB (tape and reel) 8 lead SOIC
•
•
High Output Current
± 200mA @ Vo = 9.4 Vpp, Vs = 12V
Low Distortion
-40°C to +85°C
•
•
•
High ESD (Electro-Static Discharge) immunity
4kV for Supply and Output pins
Low differential gain and phase
0.005% and -0.07deg
•
•
85dB SFDR (Spurious Free Dynamic Range)
@ 100KHz, Vo = 2Vpp, RL = 25Ω
•
•
•
High Speed
•
•
•
192MHz 3dB bandwidth (G=2)
240V / µs slew rate
Applications
Low Noise
•
•
•
ADSL PCI modem cards
xDSL external modem
Line Driver
•
•
3.8nV / √Hz: input noise voltage
2.7pA / √Hz: input noise current
Low supply current: 7mA/amp
•
Single-supply operation: 5V to 12V
8
7
6
5
Out_1
V+
1
In_n_1
In_p_1
V -
Out_2
In_n_2
In_p_2
2
3
4
1
2
ZL40167
Figure 1 - Functional Block Diagram and Pin Connection
1
Zarlink Semiconductor Inc.
Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc.
Copyright 2003, Zarlink Semiconductor Inc. All Rights Reserved.
ZL40167
Data Sheet
Description
The ZL40167 is a low cost voltage feedback opamp capable of driving signals to within 1V of the power supply rails.
It features low noise and low distortion accompanied by a high output current which makes it ideally suited for the
application as an xDSL line driver. The dual opamp can be connected as a differential line driver delivering signals
up to 18.8Vpp swing into a 25Ω load, fully supporting the peak upstream power levels for upstream full-rate ADSL
(Asymmetrical Digital Subscriber Line).
The wide bandwidth, high power output and low differential gain and phase figures make the ZL40167 ideally suited
for a wide variety of video driver applications.
Application Notes
The ZL40167 is a high speed, high output current, dual operational amplifier with a high slew rate and low
distortion. The device uses conventional voltage feedback for ease of use and more flexibility. These characteristics
make the ZL40167 ideal for applications where driving low impedances of 25 to 100Ω such as xDSL and active
filters.
The figure below shows a typical ADSL application utilising a 1:2 transformer, the feedback path provides a
Gain = +2.
12R5
Rf1
Rg
100R
Rf2
12R5
Figure 2 - A Typical ADSL Application
A class AB output stage allows the ZL40167 to deliver high currents to low impedance loads with low distortion
while consuming low quiescent current.
Note: the high ESD immunity figure of 4kV may mean that in some designs fewer additional EMC protection
components are needed thus reducing total system costs.
The ZL40167 is not limited to ADSL applications and can be used as a general purpose opamp configured with
either inverting or non-inverting feedback. The figure below shows non-inverting feedback arrangement that has
typically been used to obtain the data sheet specifications.
2
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Rf
Rg
Figure 3 - A Non-Inverting Feedback Amplifier Example
Video transmitter and receiver for twisted wire pair
Composite video signals can be transmitted down twisted pair cable, i.e. Ethernet (CAT 5), using a differential
transmitter and receiver. The transmitter must be able to drive high currents into the low impedance twisted pair
cable. For video, the amplifiers require flat gain and low phase-shift over the video signal band. To ensure this, the
amplifiers will have 3dB bandwidths well in excess of this. The ZL40167 (dual amplifier) has all of these attributes.
With reference to the differential video driver shown in Figure , the input coax is assumed to have a characteristic
impedance of 75 Ohms, this is terminated with a parallel combination of 110 Ohms and the input impedance of
amplifier IC1 (b) of 255 Ohms, giving 77 Ohms. Low values of feedback resistors are used around the op-amps to
reduce phase-shift due to parasitic capacitors and to minimise the addition of noise.
Baseband PAL or NTSC video signals generally have an amplitude of 2V pk-pk. A gain of two is used to ensure that
the signal level at the end of the (terminated with 100 Ohms) differential pair will be the same as the input level,
neglecting any losses due to the use of long cable lengths.
Composite Video
Co-Ax Input
IC1(a)
50R
50R
110R
510R
510R
510R
510R
510R
Twisted Pair
Output
IC1(b)
Figure 4 - Differential Video Driver
The differential receiver is shown in Figure 5 has a 100 Ohm line termination resistor, followed by a differential
amplifier. Long cables will tend to attenuate the signal with greater losses at the higher frequencies, so the second
amplifier is used to equalise these losses. Initially the amplifier should be built without fitting components R1 and
3
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
C1. Select the value of R2 to give the required gain at low frequency. Adjust the values of R1 and C1 to correct for
the frequency dependant attenuation of the cable.
To drive a coax cable the output of the amplifier is connected via a series matching 75 Ohm resistor, again this
second (dual amplifier) ZL40167 provides the required power output for the restored 2Vpk-pk video signal.
510R
510R
IC2(a)
Twisted Pair
100R
Input
510R
510R
R2
Composite Video
C1
R1
Co-Ax Output
IC2(b)
75R
510R
Figure 5 - Differential Video Receiver
4
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Absolute Maximum Ratings - (See Note 1)
Parameter
Symbol
Min
Max
Units
Vin Differential
V
±1.2
V
IN
Output Short Circuit Protection
V
See Apps
Note in this
data sheet
OS/C
Supply Voltage
V+, V-
±13.2
(V+) +0.8
±5.5
V
V
Voltage at Input Pins
Voltage at Output Pins
V
, V
(V-) -0.8
(+IN)
(-IN)
V
V
O
ESD Protection (HBM Human Body Model)
(See Note 2)
4
(Note 3)
kV
Storage Temperature
Latch-up test
-55
+150
°C
+/-100mA
for 100ms
(Note 4)
Supply transient test
20% pulse
for 100ms
(Note 5)
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate
conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed
specifications and the test conditions, see the Electrical Characteristics.
Note 2: Human body model, 1.5kΩ in series with 100pF. Machine model, 200Ω in series with 100pF.
Note 3: 1.25kV between the pairs of +INA, -INA and +INB, -INB pins only. 4kV between supply pins, OUTA or OUTB pins and any
input pin.
Note 4: +/-100mA applied to input and output pins to force the device to go into “latch-up”. The device passes this test to JEDEC spec
17.
Note 5: Positive and Negative supply transient testing increases the supplies by 20% for 100ms.
Operating Ratings - (See Note 1)
Parameter
Symbol
Min
Max
Units
Supply Voltage
V+, V-
± 2.5
-40
±6.5
V
Junction Temperature Range
Junction to Ambient Resistance
150
°C
Rth(j-a)
Rth(j-c)
150
°C
4 layer FR5
board
Junction to Case Resistance
60
°C
4 layer FR5
board
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate
conditions for which the device is intended to be functional, but specific performance is not guaranteed. For guaranteed
specifications and the test conditions, see the Electrical Characteristics.
5
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Electrical Characteristics - TA = 25°C, G = +2, Vs = ± 6V, Rf = Rg = 510Ω, RL = 100Ω / 2pF; Unless
otherwise specified.
Min
Typ
Max
Test
Type
Symbol
Parameter
Conditions
Units
(Note 1) (Note 2) (Note 3)
Dynamic Performance
-3dB Bandwidth
Vo = 200mVp-p
192
32
MHz
MHz
V/µs
ns
C
C
C
C
C
-0.1dB Bandwidth
Slew Rate
Vo = 200mVp-p
4V Step O/P, 10-90%
4V Step O/P, 10-90%
240
13.3
1.7
Rise and Fall Time
Rise and Fall Time
200mV Step O/P,
10-90%
ns
Differential Gain
NTSC, RL = 150Ω
NTSC, RL = 150Ω
0.005
-0.07
%
C
C
Differential Phase
deg
Distortion and Noise Response
nd
2
Harmonic
Vo = 8.4Vpp,
-65.4
-83.8
-93.6
-86
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
C
C
C
C
C
C
C
C
Distortion
f =100KHz,RL= 25Ω/2pF
Vo = 8.4Vpp,
f =1MHz,RL = 100Ω/2pF
Vo = 2Vpp,
f =100kHz,RL= 25Ω/2pF
Vo = 2Vpp,
f =1MHz,RL =100Ω/2pF
rd
3
Harmonic
Vo = 8.4Vpp,
-70
Distortion
f =100KHz,RL=25Ω/2pF
Vo = 8.4Vpp,
-77.7
-85
f =1MHz,RL =100Ω/2pF
Vo = 2Vpp,
f =100KHz,RL=25Ω/2pF
Vo = 2Vpp,
-73.5
f =1MHz,RL=100Ω/2pF
MTPR
Multi-Tone Power
Ratio
47.4375 KHz
69 KHz
-75
-76.3
-73.8
-71.5
3.85
2.7
dBc
dBc
C
C
C
C
C
C
90.5625 KHz
112.125 KHz
dBc
dBc
Input Noise Voltage f = 100KHz
Input Noise Current f = 100KHz
nV/√Hz
pA/√Hz
6
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Min
Typ
Max
Test
Type
Symbol
Parameter
Conditions
Units
(Note 1) (Note 2) (Note 3)
Input Characteristics
Vos
Ib
Input Offset Voltage Tj = -40°C to 150°C
Input Bias Current Tj = -40°C to 150°C
Input Offset Current Tj = -40°C to 150°C
- 4.2
- 0.3
-10
4.2
-20
2
mV
µA
µA
V
A
A
A
A
Ios
-2
-0.2
CMVR
Common Mode
Voltage Range
Tj = -40°C to 150°C
- 4.9
4.9
CMRR
Common Mode
Rejection Ratio
Tj = -40°C to 150°C
70
79
10
dB
A
Transfer Characteristics
Avol
Voltage Gain
RL = 1k,
4.7
V/mV
A
Tj = -40°C to 150°C
RL = 25Ω,
1.6
- 4.5
- 5
5.5
A
A
A
B
Tj = -40°C to 150°C
Output Swing
Output Swing
RL = 25Ω,
± 4.7
± 5.1
1000
4.5
5
V
V
Tj = -40°C to 150°C
RL = 1k,
Tj = -40°C to 150°C
Isc
Output Current
(Note 3)
Vo = 0,
570
mA
Tj = -40°C to 150°C
Power Supply
Is
Supply
Tj = -40°C to 150°C
Tj = -40°C to 150°C
7
9
mA
dB
A
A
Current / Amp
PSRR
Power Supply
Rejection Ratio
73
81
Note 1: The maximum power dissipation is a function of Tj(max), θJA and TA. The maximum allowable power dissipation at any
ambient temperature is PD = (Tj(max) - TA)/ θJA. All numbers apply for packages soldered directly onto a PC board.
Note 2: Typical values represent the most likely parametric norm.
Note 3: Test Types:
a. 100% tested at 25°C. Over temperature limits are set by characterisation, simulation and statistical analysis.
b. Limits set by characterisation, simulation and statistical analysis.
c. Typical value only for information.
7
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
± 2.5V Electrical Characteristics - TA = 25°C, G = +2, Vs = ± 2.5V, Rf = Rg = 510Ω, RL = 100Ω / 2pF; Unless
otherwise specified.
Min
(Note 1)
Typ
Max
Test
Type
Symbol
Parameter
Conditions
Units
(Note 2) (Note 3)
Dynamic Performance
-3dB Bandwidth
176.5
83.8
216
3.7
MHz
MHz
V/µs
ns
C
C
C
C
C
-0.1dB Bandwidth
Slew Rate
1V Step O/P, 10-90%
1V Step O/P, 10-90%
Rise and Fall Time
Rise and Fall Time
200mV Step O/P,
10-90%
1.7
ns
Distortion and Noise Response
nd
2
Harmonic
Vo = 2Vpp,f = 100KHz,
-92.6
-85
dBc
dBc
dBc
dBc
C
C
C
C
Distortion
RL = 25Ω
Vo = 2Vpp, f = 1MHz,
RL = 100Ω
rd
3 Harmonic
Vo = 2Vpp, f = 100KHz,
-86.3
-74.8
Distortion
RL = 25Ω
Vo = 2Vpp, f = 1MHz,
RL = 100Ω
Input Characteristics
Vos
Ib
Input Offset Voltage Tj = -40°C to 150°C
- 4.2
- 0.3
- 10
4.2
-20
mV
µA
V
B
B
B
Input Bias Current
Tj = -40°C to 150°C
CMVR
Common Mode
Voltage Range
-1.55
70
1.55
CMRR
Common Mode
Rejection Ratio
Tj = -40°C to 150°C
80
dB
B
Transfer Characteristics
Avol Voltage Gain
RL = 1k, Tj = -40°C to
150°C
5.5
1.6
10.5
5.8
V/mV
B
B
RL = 25Ω, Tj = -40°C to
150°C
Output Characteristics
Output Swing
RL = 25Ω, Tj = -40°C to
150°C
-1.4
-1.6
±1.45
±1.65
1.4
1.6
V
B
B
RL = 1k, Tj = -40°C to
150°C
8
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Min
(Note 1)
Typ
Max
Test
Type
Symbol
Parameter
Conditions
Units
(Note 2) (Note 3)
Power Supply
Is
Supply
Current/Amp
Tj = -40°C to 150°C
Tj = -40°C to 150°C
6.75
83
8.5
mA
dB
A
B
PSRR
Power Supply
Rejection Ratio
73
Note 1: The maximum power dissipation is a function of Tj(max), θJA and TA. The maximum allowable power dissipation at any
ambient temperature is PD = (Tj(max) - TA)/ θJA. All numbers apply for packages soldered directly onto a PC board.
Note 2: Typical values represent the most likely parametric norm.
Note 3: Test Types:
a. 100% tested at 25°C. Over temperature limits are set by characterisation, simulation and statistical analysis.
b. Limits set by characterisation, simulation and statistical analysis.
c. Typical value only for information.
9
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100,Vs = 6V. Unless
otherwise specified.
Output Swing
12.0
10.0
8.0
RL = 1K
6.0
RL = 25
4.0
2.0
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
+/- Supply (V)
Figure 6 - Output Swing
Positive Output Swing into 1Kohms
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
- 40 C
25 C
85 C
1.0
2.0
3.0
4.0
5.0
6.0
7.0
+/- Supply (V)
Figure 7 - Positive Output Swing into 1KΩ
10
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Negative Output Swing into 1Kohms
1.0
- 4 0 C
0.9
2 5 C
0.8
85 C
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
+/- Supply (V)
Figure 8 - Negative Output Swing into 1KΩ
Positive Output Swing into 25 ohms
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
-40 C
25 C
85 C
1.0
2.0
3.0
4.0
5.0
6.0
7.0
+/- Supply (V)
Figure 9 - Positive Output Swing into 25Ω
11
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Negative Output Swing into 25 ohms
1.4
1.2
25 C
- 40 C
1.0
0.8
0.6
0.4
0.2
0.0
85 C
1.0
2.0
3.0
4.0
5.0
6.0
7.0
+/- Supply (V)
Figure 10 - Negative Output Swing into 25Ω
+Vout vs. ILoad
5.4
5.3
5.2
5.1
5.0
4.9
4.8
4.7
4.6
85 C
25 C
- 40 C
0.00
0.05
0.10
0.15
0.20
0.25
ILoad (A)
Figure 11 - +Vout vs. lLoad
12
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
-Vout vs. ILoad
5.4
5.3
5.2
5.1
85 C
5.0
25 C
4.9
- 40 C
4.8
4.7
4.6
0.00
0.05
0.10
0.15
0.20
0.25
ILoad (A)
Figure 12 - -Vout vs. lLoad
+Vout vs. ILoad, VS = 2.5V
2.0
1.9
1.8
1.7
1.6
1.5
1.4
1.3
1.2
1.1
1.0
25 C
85 C
- 40 C
0.00
0.05
0.10
0.15
0.20
0.25
ILoad (A)
Figure 13 - +Vout vs. lLoad, Vs = ±2.5V
13
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
-Vout vs. ILoad, VS = 2.5V
2.0
1.9
1.8
2 5 C
1. 7
8 5 C
1.6
1. 5
1.4
- 4 0
C
1.3
1.2
1.1
1.0
0.00
0.05
0.10
0.15
0.20
0.25
ILoad (A)
Figure 14 - -Vout vs. lLoad, Vs ±2.5V
Vout vs. RLoad
85 C
5.5
5.0
4.5
4.0
3.5
3.0
25 C
-40 C
0
10
20
30
40
50
60
70
80
90
100
110
RLoad (ohms)
Figure 15 - Vout vs Rload
14
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Supply Current
16.0E-3
25 C
85 C
14.0E-3
12.0E-3
10.0E-3
8.0E-3
- 40 C
6.0E-3
4.0E-3
2.0E-3
000.0E+0
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
+/- Supply (V)
Figure 16 - Supply Current vs. Supply Voltage
Source Current, Vo = 0V
1.4
25 C
1.2
1.0
- 40 C
85 C
0.8
0.6
0.4
0.2
0.0
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
+/- Supply (V)
Figure 17 - Sourcing Current vs. Supply Voltage
15
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Sinking Current, Vo = 0V
1.2
- 40 C
85 C
25 C
1.0
0.8
0.6
0.4
0.2
0.0
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
+/- Supply (V)
Figure 18 - Sinking Current vs. Supply Voltage
Vos vs. VS
140.0E-6
120.0E-6
100.0E-6
80.0E-6
60.0E-6
40.0E-6
20.0E-6
000.0E+0
85 C
- 40 C
25 C
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
+/- Supply (V)
Figure 19 - Vos vs. VS
16
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Vos vs Vcm
7.0E-3
6.0E-3
5.0E-3
4.0E-3
3.0E-3
2.0E-3
85 C
1.0E- 3
- 40 C
25 C
000.0E+0
0.0
1.0
2.0
3.0
4.0
5.0
6.0
Vcm (V)
Figure 20 - Vos vs. Vcm
Vos vs. Vcm, VS = +/- 2.5V
600.0E-6
500.0E-6
400.0E-6
300.0E-6
200.0E-6
100.0E-6
000.0E+0
25 C
85 C
-40 C
0.0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
Vcm (V)
Figure 21 - Vos vs. Vcm, Vs = ±2.5V
17
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Bias Current vs. Vsupply
-4.0E-6
-4.5E-6
-5.0E-6
-5.5E-6
- 40 C
-6.0E-6
-6.5E-6
25 C
-7.0E-6
-7.5E-6
85 C
-8.0E-6
-8.5E-6
-9.0E-6
1.0
2.0
3.0
4.0
5.0
6.0
7.0
+/- Supply (V)
Figure 22 - Bias Current vs. Vsupply
Offset Current vs. Vsupply
25.0E-9
20.0E-9
15.0E- 9
10.0E- 9
5.0E-9
85 C
25 C
- 40 C
000.0E+0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
+/- Supply (V)
Figure 23 - Offset Current vs. Vsupply
18
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Harmonic Distortion vs. Load
F = 1MHz, Vout = 2Vpp
-60
-65
-70
3r d Har monic
-75
-80
-85
-90
2nd Har monic
-95
-100
-105
0
50
100
150
200
250
300
350
400
450
500
Load Resistance (ohms)
Figure 24 - Harmonic Distortion vs. Load F = 1MHZ, Vout = 2Vpp
Harmonic Distortion vs. Load
VS = +/- 2.5V, F = 1MHz, Vout = 2Vpp
-60
-65
-70
-75
3r d Har monic
2nd Har monic
-80
-85
-90
-95
-100
-105
0
50
100
150
200
250
300
350
400
450
500
Load Resistance (ohms)
Figure 25 - Harmonic Distortion vs. Load Vs = ±2.5V, F = 1MHz, Vout = 2Vpp
19
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Harmonic Distortion vs. Output Voltage
VS = +/- 2.5V, F = 1MHz
-40
-50
-60
3r d Har monic
-70
-80
-90
2nd Har monic
-100
-110
0.0
0.5
1.0
1.5
2.0
2.5
3.0
Output Voltage (Vpp)
Figure 26 - Harmonic Distortion vs. Output Voltage Vs = ±2.5V, F = 1MHz
Harmonic Distortion vs. Output Voltage
F = 1MHz
-40
-50
-60
-70
3r d Har monic
-80
-90
2nd Har monic
-100
-110
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
Output Voltage (Vpp)
Figure 27 - Harmonic Distortion vs. Output Voltage F = 1MHz
20
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Harmonic Distortion vs. Output Voltage
VS = +/- 2.5V, F = 1MHz, RL = 25ohms
-40
-50
3r d Har monic
-60
-70
2nd Har monic
-80
-90
-100
0.0
0.5
1.0
1.5
2.0
2.5
3.0
Output Voltage (Vpp)
Figure 28 - Harmonic Distortion vs. Output Voltage Vs = ±2.5V, F = 1MHz, RL = 25Ω
Harmonic Distortion vs. Output Voltage
F = 1MHz, RL = 25ohm s
-40
-50
-60
-70
-80
-90
-100
2nd Har monic
3r d Har monic
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
Output Voltage (Vpp)
Figure 29 - Harmonic Distortion vs. Output Voltage F = 1MHz, RL = 25Ω
21
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Harmonic Distortion vs. Output Voltage
F = 10MHz
-20
-30
3r d Har monic
-40
-50
2nd Har monic
-60
-70
-80
-90
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
Output Voltage (Vpp)
Figure 30 - Harmonic Distortion vs. Output Voltage F = 10MHz
Harmonic Distortion vs. Output Voltage
F = 10MHz, RL = 25ohm s
-20
-30
-40
-50
-60
-70
-80
3r d Har monic
2nd Har monic
0.0
1.0
2.0
3.0
4.0
5.0
6.0
7.0
8.0
9.0
10.0
Output Voltage (Vpp)
Figure 31 - Harmonic Distortion vs. Output Voltage F = 10MHz, RL = 25Ω
22
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Harmonic Distortion vs. Frequency
Vout = 2Vpp
-30
-40
-50
-60
3r d Har monic
-70
-80
2nd Har monic
-90
-100
-110
-120
100.0E+3
1.0E+6
10.0E+6
Frequency (Hz)
Figure 32 - Harmonic Distortion vs. Frequency Vout = 2Vpp
Harmonic Distortion vs. Output Voltage
VS = +/- 2.5V, F=10MHz
-30
-40
-50
-60
-70
-80
3r d Har monic
2nd Ha r monic
-90
0.0
0.5
1.0
1.5
2.0
2.5
3.0
Output Voltage (Vpp)
Figure 33 - Harmonic Distortion vs. Output Voltage Vs = ±2.5V, F = 10MHz
23
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Harmonic Distortion vs. Frequency
Vout = 2Vpp, RL = 25ohms
-30
-40
-50
3r d Har monic
-60
-70
2nd Har monic
-80
-90
-100
-110
100.0E+3
1.0E+6
10.0E+6
Frequency (Hz)
Figure 34 - Harmonic Distortion vs. Frequency Vout = 2Vpp, RL = 25Ω
Harmonic Distortion vs. Output Voltage
VS = +/- 2.5V, F = 10MHz, RL = 25 ohms
-20
-30
-40
-50
-60
-70
-80
3 r d Har monic
2nd Har monic
0.0
0.5
1.0
1.5
2.0
2.5
3.0
Output Voltage (Vpp)
Figure 35 - Harmonic Distortion vs. Output Voltage Vs = ±2.5V, F = 10MHz, RL = 25Ω
24
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Harmonic Distortion vs. Frequency
VS = +/- 2.5V, Vout = 2Vpp
-30
-40
-50
-60
3r d Har monic
-70
-80
2nd Har monic
-90
-100
-110
-120
100.0E+3
1.0E+6
10.0E+6
Frequency (Hz)
Figure 36 - Harmonic Distortion vs. Frequency Vs = ±2.5V, Vout = 2Vpp
Harmonic Distortion vs. Frequency
VS = +/- 2.5V, Vout = 2Vpp, RL = 25ohms
-30
-40
-50
-60
-70
-80
-90
-100
-110
3r d Har monic
2nd Har monic
100.0E+3
1.0E+6
10.0E+6
Frequency (Hz)
Figure 37 - Harmonic Distortion vs. Frequency Vs = ±2.5V, Vout = 2Vpp, RL = 25Ω
25
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Small Signal Frequency Response
25.0
G = 10
20.0
15.0
G = 5
10.0
5.0
G = 2
0.0
-5.0
-10.0
1.0E+3
10.0E+3
100.0E+3
1.0E+6
10.0E+6
100.0E+6
1.0E+9
Frequency (Hz)
Figure 38 - Small Signal Frequency Response
Frequency Response, Vo = 200mVpp
8.0
VS = 12V
6.0
4.0
2.0
VS = 5V
0.0
-2.0
-4.0
-6.0
100.0E+3
1.0E+6
10.0E+6
100.0E+6
1.0E+9
Frequency (Hz)
Figure 39 - Frequency Response, VO = 200mVpp
26
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Pulse Response
2.5
2.0
1.5
1.0
0.5
0.0
-0.5
-1.0
-1.5
-2.0
-2.5
5.4E-6
5.5E-6
5.6E-6
5.7E-6
5.8E-6
5.9E-6
6.0E-6
6.1E-6
Time (s)
Figure 40 - Pulse Response
Pulse Response, VS = +/- 2.5V
0.6
0.4
0.2
0.0
-0.2
-0.4
-0.6
5.4E-6
5.5E-6
5.6E-6
5.7E-6
5.8E-6
5.9E-6
6.0E-6
6.1E-6
Time (s)
Figure 41 - Pulse Response, Vs = ±2.5V
27
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
PSRR vs. Frequency
100
90
80
70
60
50
40
30
20
10
0
10.0E+0
100.0E+0
1.0E+3
10.0E+3
100.0E+3
1.0E+6
10.0E+6
Frequency (Hz)
Figure 42 - PSRR vs Frequency
CMRR vs. Frequency
90
80
70
60
50
40
30
20
10
0
10.0E+0
100.0E+0
1.0E+3
10.0E+3
100.0E+3
1.0E+6
10.0E+6
Frequency (Hz)
Figure 43 - CMRR vs. Frequency
28
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
PSRR vs. Frequency
VS = +/- 2.5V
100
90
80
70
60
50
40
30
20
10
0
10.0E+0
100.0E+0
1.0E+3
10.0E+3
100.0E+3
1.0E+6
10.0E+6
Frequency (Hz)
Figure 44 - PSRR vs. Frequency Vs = ±2.5V
CMRR vs. Frequency
VS = +/- 2.5V
90
80
70
60
50
40
30
20
10
0
10.0E+0
100.0E+0
1.0E+3
10.0E+3
100.0E+3
1.0E+6
10.0E+6
Frequency (Hz)
Figure 45 - CMRR vs. Frequency Vs = ±2.5V
29
Zarlink Semiconductor Inc.
ZL40167
Data Sheet
Typical Performance Characteristics At TA = 25°C, RF = RG = 510, gain = +2, RL = 100, Vs = 6V. Unless
otherwise specified.
Input Noise Voltage vs. Frequency
3.85E-09
3.80E-09
3.75E-09
3.70E-09
VS =+/ - 2. 5V
3.65E-09
3.60E-09
VS =+/ - 6V
3.55E-09
100.0E+0
1.0E+3
10.0E+3
100.0E+3
1.0E+6
10.0E+6
Frequency (Hz)
Figure 46 - Noise Voltage vs. Frequency
Input Current Noise vs. Frequency
4.0E-12
3.8E-12
3.6E-12
3.4E-12
3.2E-12
3.0E-12
2.8E-12
2.6E-12
2.4E-12
2.2E-12
2.0E-12
VS=+/-2.5V
VS=+/-6V
100.0E+0
1.0E+3
10.0E+3
100.0E+3
1.0E+6
10.0E+6
Frequency (Hz)
Figure 47 - Current Noise vs. Frequency
30
Zarlink Semiconductor Inc.
For more information about all Zarlink products
visit our Web Site at
www.zarlink.com
Information relating to products and services furnished herein by Zarlink Semiconductor Inc. trading as Zarlink Semiconductor or its subsidiaries (collectively
“Zarlink”) is believed to be reliable. However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the
application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may
result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under
patents or other intellectual property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified
that the use of product in certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property
rights owned by Zarlink.
This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part
of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other
information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the
capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute
any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and
suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does
not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in
significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink’s conditions of sale which are available on request.
Purchase of Zarlink’s I2C components conveys a licence under the Philips I2C Patent rights to use these components in and I2C System, provided that the system
conforms to the I2C Standard Specification as defined by Philips.
Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc.
Copyright Zarlink Semiconductor Inc. All Rights Reserved.
TECHNICAL DOCUMENTATION - NOT FOR RESALE
相关型号:
ZL40167/DCB
Operational Amplifier, 2 Func, 4200uV Offset-Max, PDSO8, 0.150 INCH, MS-012AA, SOIC-8
MICROSEMI
ZL40167/DCB
Operational Amplifier, 2 Func, 4200uV Offset-Max, PDSO8, 0.150 INCH, MS-012AA, SOIC-8
ZARLINK
ZL40213LDG1
Low Skew Clock Driver, 4000/14000/40000 Series, 4 True Output(s), 0 Inverted Output(s), CMOS, 3 X 3 MM, 0.90 MM HEIGHT, 0.50 MM PITCH, QFN-16
MICROSEMI
ZL40219LDG1
Low Skew Clock Driver, 4000/14000/40000 Series, 16 True Output(s), 0 Inverted Output(s), CMOS
MICROCHIP
©2020 ICPDF网 联系我们和版权申明