2ED21091S06FXUMA1中文资料_数据手册_规格书

2ED21091S06F

650 V half bridge gate driver with integrated bootstrap diode

Features

Product summary

•

Unique Infineon Thin-Film-Silicon On Insulator (SOI)-technology

V_{S_OFFSET}= 650 V max.

I_o+pk/ I_o-pk(typ.) = + 0.29 A/ - 0.7 A

V_CC= 10 V to 20 V

Internal deadtime = 540 ns typ.

t_ON/ t_OFF(typ.) = 740 ns/ 200 ns

Negative VS transient immunity of 100 V

Floating channel designed for bootstrap operation

Operating voltages (VS node) upto + 650 V

Maximum bootstrap voltage (VB node) of + 675 V

Integrated ultra-fast, low resistance bootstrap diode

Logic operational up to –11 V on VS Pin

Negative voltage tolerance on inputs of –5 V

Independent under voltage lockout for both channels

Schmitt trigger inputs with hysteresis

Packages

3.3 V, 5 V and 15 V input logic compatible

Maximum supply voltage of 25 V

Internal 540 ns dead time and programmable up to 2.7 us with

external resistor

The dual function DT/SD input turns off both channels

RoHS compliant

•

DSO-8

Potential applications

Driving IGBTs, enhancement mode N-Channel MOSFETs in various power electronic applications.

Typical Infineon recommendations are as below:

•

Motor drives, general purpose inverters having TRENCHSTOP™ IGBT6 or 600 V EasyPACK™ modules or its

equivalent power stages

Refrigeration compressors, induction cookers, other major home appliances having RCD series IGBTs or

TRENCHSTOP™ family IGBTs or their equivalent power stages

Battery operated small home appliances such as power tools, vaccum cleaners using low voltage

OptiMOS™ MOSFETs or their equivalent power stages

Totem pole, half-bridge and full-bridge converters in offline AC-DC power supplies for industrial SMPS having

high voltage CoolMOS™ super junction MOSFETs or TRENCHSTOP™ H3 and WR5 IGBT series or their

equivalent

High power LED and HID lighting having CoolMOS™ super junction MOSFETs

Electric vehicle (EV) charging stations and battery management systems

Driving 650 V SiC MOSFETs in above applications

•

Product validation

Qualified for industrial applications according to the relevant tests of JEDEC47/20/22

Ordering information

Standard pack

Base part number Package type

2ED21091S06F DSO - 8

Orderable part number

2ED21091S06FXUMA1

Form

Quantity

2500

Tape and Reel

Datasheet

www.infineon.com/soi

Please read the Important Notice and Warnings at the end of this document

Page 1 of 25

V 2.10

2019-09-12

2ED21091S06F

650 V half bridge gate driver with integrated bootstrap diode

Description

The 2ED21091S06F is a high voltage, high speed power MOSFET and IGBT driver with independent high and low

side referenced output channels. Based on Infineon’s SOI-technology there is an excellent ruggedness and

noise immunity with capability to maintain operational logic at negative voltages of up to - 11 V on VS pin (V_CC

=

15 V) on transient voltages. There are not any parasitic thyristor structures present in the device, hence no

parasitic latch up may occur at all temperature and voltage conditions. The logic input is compatible with

standard CMOS or LSTTL output, down to 3.3 V logic. The output drivers feature a high pulse current buffer

stage designed for minimum driver cross-conduction. The floating channel can be used to drive an N-channel

power MOSFET, SiC MOSFET or IGBT in the high side configuration, which operate up to 650 V.

Refer to lead assignments for

correct pin configuration. This

diagram shows electrical

connections only. Please refer to

our application notes and design

tips for proper circuit board

layout.

*Bootstrap diode is monolithically integrated

Figure 1

Typical application block diagram

Summary of feature comparison of the 2ED210x family:

Table 1

Cross

Input

logic

conduction

prevention

logic

Part No.

Deadtime

Ground pins t_ON/ t_OFFPackage

2ED2106S06F

2ED21064S06J

2ED2108S06F

COM

DSO - 8

DSO - 14

DSO - 8

HIN, LIN

No

None

VSS / COM

COM

200 ns /

200 ns

Internal 540 ns

HIN, LIN

Yes

Programmable

540 ns - 5000 ns

2ED21084S06J

2ED2109S06F

2ED21094S06J

VSS / COM

COM

DSO - 14

DSO - 8

Internal 540 ns

IN, SD

Yes

Programmable

540 ns - 5000 ns

VSS / COM

740 ns / DSO - 14

200 ns

Programmable

540 ns - 2700 ns

2ED21091S06F IN, DT/SD Yes

COM

DSO – 8

Datasheet

www.infineon.com/soi

2 of 25

V 2.10

2019-09-12

2ED21091S06F

650 V half bridge gate driver with integrated bootstrap diode

1

Table of contents

Table of contents.................................................................................................................................. 3

2

Block diagram ...................................................................................................................................... 4

3

3.1

3.2

Pin configuration and functionality ..................................................................................................... 5

Pin configuration.....................................................................................................................................5

Pin functionality......................................................................................................................................5

4

Electrical parameters ........................................................................................................................... 6

Absolute maximum ratings.....................................................................................................................6

Recommended operating conditions.....................................................................................................6

Static electrical characteristics ..............................................................................................................7

Dynamic electrical characteristics..........................................................................................................8

4.1

4.2

4.3

4.4

5

5.1

5.2

5.3

5.4

5.5

5.6

5.7

Application information and additional details .................................................................................. 9

IGBT / MOSFET gate drive .......................................................................................................................9

Switching and timing relationships........................................................................................................9

Deadtime ...............................................................................................................................................10

Matched propagation delays................................................................................................................10

Shutdown input.....................................................................................................................................11

Input logic compatibility.......................................................................................................................11

Undervoltage lockout ...........................................................................................................................12

Bootstrap diode.....................................................................................................................................12

Calculating the bootstrap capacitance C_BS..........................................................................................13

Tolerant to negative tranisents on input pins......................................................................................14

Negative voltage transient tolerance of VS pin....................................................................................15

NTSOA – Negative Transient Safe Operating Area...............................................................................16

Higher headroom for input to output signal transmission with logic operation upto -11 V..............17

Maximum switching frequency.............................................................................................................18

PCB layout tips ......................................................................................................................................19

5.8

5.9

5.10

5.11

5.12

5.13

5.14

5.15

6

7

8

9

Qualification information................................................................................................................... 20

Related products................................................................................................................................ 20

Package details .................................................................................................................................. 21

Part marking information .................................................................................................................. 22

10

10.1

Additional documentation and resources ......................................................................................... 23

Infineon online forum resources ..........................................................................................................23

11

Revision history .................................................................................................................................. 24

Datasheet

www.infineon.com/soi

3 of 25

V 2.10

2019-09-12

2ED21091S06F

650 V half bridge gate driver with integrated bootstrap diode

2

Block diagram

8

VB

UV

DETECT

R

S

7

6

HO

VS

Q

Pulse

Filter

2ED21091S06F

VSS/COM

LEVEL

SHIFT

2

IN

Pulse

Generator

BS diode

1

VCC

Deadtime

UV

DETECT

VSS/COM

LEVEL

SHIFT

5

4

LO

Delay

Match

3

DT/SD

COM

Figure 2

Block diagrams

Datasheet

www.infineon.com/soi

4 of 25

V 2.10

2019-09-12

2ED21091S06F

650 V half bridge gate driver with integrated bootstrap diode

3

Pin configuration and functionality

3.1

Pin configuration

8

VB

HO

VS

LO

1

2

3

4

VCC

IN

7

6

5

DT/SD

COM

8 - Lead DSO - 8 (150 mil)

2ED21091S06F

Figure 3

2ED2109S06F pin assignments (top view)

3.2

Pin functionality

Table 2

Symbol

VCC

Description

Low-side and logic supply voltage

Logic input for high-side and low-side gate driver output (HO and LO), in phase

with HO. Schmitt trigger input with hysteresis and pull down

IN

DT/SD

COM

LO

Logic input for shut down (out of phase) and programmable dead time pin

Low-side gate drive return

Low-side driver output

VS

High voltage floating supply return

High-side driver output

HO

VB

High-side gate drive floating supply

Datasheet

www.infineon.com/soi

5 of 25

V 2.10

2019-09-12

2ED21091S06F

650 V half bridge gate driver with integrated bootstrap diode

4

Electrical parameters

4.1

Absolute maximum ratings

Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All

voltage parameters are absolute voltages referenced to COM unless otherwise stated in the table. The thermal

resistance and power dissipation ratings are measured under board mounted and still air conditions.

Table 3

Absolute maximum ratings

Definition

Symbol

V_B

Min.

V_CC– 5

V_CC– V_BS– 5

V_S– 0.5

-1

Max.

675

650

V_B+ 0.5

25

Units

V

High-side floating well supply voltage ^{Note 1}

High-side floating well supply return voltage

Floating gate drive output voltage

Floating gate drive voltage supply voltage

Low side supply voltage

V_S

V_HO

V_BS

V_CC

-1

25

V_LO

V_IN

V_DT/SD

Low-side output voltage

Logic input voltage

Programmable dead time pin voltage

- 0.5

- 5

- 0.5

—

V_CC+ 0.5

4

dV_S/dt Allowable V_Soffset supply transient relative to COM

50

V/ns

W

ºC/W

P_D

Rth_JA

T_J

Package power dissipation @ T_A≤+25ºC 8 - Lead DSO - 8

Thermal resistance, junction to ambient 8 - Lead DSO - 8

Junction temperature

—

0.625

200

150

T_S

T_L

Storage temperature

Lead temperature (soldering, 10 seconds)

- 55

—

150

300

ºC

Note 1:

activated bootstrap diode.

In case V_CC> V_Bthere is an additional power dissipation in the internal bootstrap diode between pins V_CCand V_Bin case of

4.2

Recommended operating conditions

For proper operation, the device should be used within the recommended conditions. All voltage parameters

are absolute voltages referenced to COM unless otherwise stated in the table. The offset rating is tested with

supplies of (V_CC– COM) = (V_B– V_S) = 15 V.

Table 4

Recommended operating conditions

Symbol

V_B

Definition

Bootstrap voltage

High-side floating well supply voltage

High-side floating well supply offset voltage ^{Note 2}

Floating gate drive output voltage

Low-side supply voltage

Min

V_S+ 10

10

Max

V_S+ 20

20

650

V_B

20

V_CC

5

Units

V

V_BS

V_S

V_HO

V_CC

V_LO

V_IN

V_CC– V_BS– 1

V_S

10

COM

- 4

Low-side output voltage

Logic input voltage

V_DT/SDProgrammable dead time pin voltage

-0.5

12

- 40

4

150

125

R_DT

T_A

Programmable dead time resistor

Ambient temperature

kΩ

ºC

Note 2: Logic operation for V_Sof – 11 V to +650 V.

Datasheet

www.infineon.com/soi

6 of 25

V 2.10

2019-09-12

2ED21091S06F

650 V half bridge gate driver with integrated bootstrap diode

4.3

Static electrical characteristics

(V_CC– COM) = (V_B– V_S) = 15 V, and T_A= 25 °C unless otherwise specified. The V_IL,V_IHand I_INparameters are

referenced to Vss / COM and are applicable to the respective input leads: IN and DT/SD. The V_Oand I_O

parameters are referenced to V_S/ COM and are applicable to the respective output leads HO or LO. The V_CCUV

parameters are referenced to COM. The V_BSUVparameters are referenced to V_S.

Table 5

Symbol

Static electrical characteristics

Definition

V_BSsupply undervoltage positive going

threshold

Min.

7.6

Typ.

8.2

Max.

8.9

Units Test Conditions

V_BSUV

+

V_BSsupply undervoltage negative going

threshold

V_BSsupply undervoltage hysteresis

V_CCsupply undervoltage positive going

threshold

V_BSUV

6.7

—

7.2

1.0

9.1

8.1

—

-

V

V_BSUVHY

V_CCUV

8.4

9.8

+

V_CCsupply undervoltage negative going

threshold

V_CCUV

7.5

8.2

8.9

-

V_CCUVHY

I_LK

I_QBS

I_QCC

V_CCsupply undervoltage hysteresis

High-side floating well offset supply leakage

Quiescent V_BSsupply current

Quiescent V_CCsupply current

—

180

—

450

—

1.7

0.7

—

0.9

1

—

12.5

—

V_B= V_S= 650 V

uA

V

170

600

0.05

0.02

230

290

650

700

2.1

0.9

25

V_IN= 0 V or 5 V

—

V_OHHigh level output voltage drop, V_cc- V_{LO ,}V_B- V_HO

V_OLLow level output voltage drop, V_O

I_o+meanMean output current from 3 V to 6 V

0.2

0.1

—

I_O= 2 mA

C_L= 22 nF

V_O= 0 V

C_L= 22 nF

V_O= 15 V

I_o+

Peak output current turn-on¹

mA

V

I_o-meanMean output current from 12 V to 9 V

I_o-

V_IH

V_IL

V_SD,TH

Peak output current turn-off¹

Logic “1” input voltage

Logic “0” input voltage

/SD input threshold

—

2.4

1.1

50

Vcc = 10 V to 20 V

I_IN+Input bias current (Output = High)

I_IN-Input bias current (Output = Low)

IN = 5 V

IN = 0 V

V_DT/SD= 0 V

—

10

µA

V

I_SD+/SD input bias current

—

- 400

Bootstrap diode forward voltage between Vcc

and VB

V_FBSD

—

1

1.2

I_F= 0.3 mA

Bootstrap diode forward current between Vcc

and VB

R_BSDBootstrap diode resistance

I_FBSD

45

20

—

85

30

125

45

mA

Ω

V_CC- V_B= 4 V

V_F1= 4 V,V_F2= 5 V

Vcc = 15 V

Allowable Negative VS pin voltage for IN Signal

propagation to HO

V

V_S

-11

-10

¹Not subjected to production test, verified by characterization.

Datasheet

www.infineon.com/soi

7 of 25

V 2.10

2019-09-12

2ED21091S06F

650 V half bridge gate driver with integrated bootstrap diode

4.4

Dynamic electrical characteristics

V_CC= V_BS= 15 V, T_A= 25 ^oC and C_L= 1000 pF unless otherwise specified.

Table 6 Dynamic electrical characteristics

Symbol Definition

Min.

—

Typ.

740

200

100

35

Max.

1030

300

150

80

Units Test Conditions

V_IN= 0 V or 5 V

t_ONTurn-on propagation delay

t_OFFTurn-off propagation delay

tsd

t_R

Shut-down propagation delay

Turn-on rise time

V_S= 0 V

ns

t_F

Turn-off fall time

—

MT

Delay matching time (HS & LS turn-on/off)

—

70

350

1.9

—

540

2.7

0

730

3.5

70

RDT = 12 Ω

RDT = 150 kΩ

RDT = 12 Ω

DT

Dead time

us

ns

MDT

Matching Dead time

—

0

600

RDT = 150 kΩ

Datasheet

www.infineon.com/soi

8 of 25

V 2.10

2019-09-12

2ED21091S06F

650 V half bridge gate driver with integrated bootstrap diode

5

Application information and additional details

5.1

IGBT / MOSFET gate drive

The 2ED21091S06F HVIC is designed to drive MOSFET or IGBT power devices. Figure 4 and Figure 5 illustrate

several parameters associated with the gate drive functionality of the HVIC. The output current of the HVIC,

used to drive the gate of the power switch, is defined as I_O. The voltage that drives the gate of the external

power switch is defined as V_HOfor the high-side power switch and V_LOfor the low-side power switch; this

parameter is sometimes generically called V_OUTand in this case does not differentiate between the high-side or

low-side output voltage.

V_B

(or V_CC

)

(or V_CC)

I_O+

HO

(or LO)

+

I_O-

V_HO(or V_LO)

-

V_S

(or COM)

Figure 4

HVIC Sourcing current

Figure 5

HVIC Sinking current

5.2

Switching and timing relationships

The relationships between the input and output signals of the 2ED21091S06F are illustrated below in Figure 6

and Figure 7. From these figures, we can see the definitions of several timing parameters (i.e. t_ON, t_OFF, t_R, and t_F)

associated with this device.

IN(LO)

IN

50%

IN(HO)

SD

HO

LO

t_f

t_on

t_r

t_off

90%

LO

HO

10%

Figure 6

Switching timing diagram

Figure 7

Input/output logic diagram

Datasheet

www.infineon.com/soi

9 of 25

V 2.10

2019-09-12

2ED21091S06F

650 V half bridge gate driver with integrated bootstrap diode

5.3

Deadtime

This family of HVICs features integrated deadtime protection circuitry. The deadtime is programmable for

2ED21091S06F, it is greater design flexibility. The deadtime feature inserts a time period (a minimum deadtime)

in which both the high- and low-side power switches are held off; this is done to ensure that the power switch

being turned off has fully turned off before the second power switch is turned on. This minimum deadtime is

automatically inserted whenever the external deadtime is shorter than interal deadtime; external deadtimes

larger than internal deadtime are not modified by the gate driver. Figure 8 illustrates the deadtime period and

the relationship between the output gate signals.

The deadtime circuitry of 2ED21091S06F is matched with respect to the high- and low-side outputs. Figure 8

defines the two deadtime parameters (i.e., DT_LO-HOand DT_HO-LO); the deadtime matching parameter (MDT)

associated with the 2ED21091S06F specifies the maximum difference between DT_LO-HOand DT_HO-LO

.

Figure 8

Deadtime matching waveform definition

5.4

Matched propagation delays

The 2ED21091S06F is designed with propagation delay matching circuitry. With this feature, the IC’s response

at the output to a signal at the input requires approximately the same time duration (i.e., tON, tOFF) for both the

low-side channels and the high-side channels; the maximum difference is specified by the delay matching

parameter (MT). The propagation turn-on delay (t_ON) of the 2ED21091S06F is matched to the propagation turn-

off delay (t_OFF).

Figure 9

Delay matching waveform definition

Datasheet

www.infineon.com/soi

10 of 25

V 2.10

2019-09-12

2ED21091S06F

650 V half bridge gate driver with integrated bootstrap diode

5.5

Shutdown input

2ED21091S06F provides a shutdown functionality that allows to disable the output. When /SD in pulled down

(the disable voltage is lower than V_SD,TH) the output is disable. Once the external pull down is released, the

output is active. The relationships between the input, output and enable signals of the 2ED21091S06F are

illustrated below in Figure 7 / 10. From these figures, we can see the definition of the parameter (i.e. t_SD)

associated with this device.

Note: If the DT/SD is floating, the output is aslo disable.

Figure 10 Shutdown waveform definitions

5.6

Input logic compatibility

The input pins are based on a TTL and CMOS compatible input-threshold logic that is independent of the Vcc

supply voltage. Figure 11 illustrates an input signal to the 2ED21091S06F, its input threshold values, and the

logic state of the IC as a result of the input signal. The typical high threshold (V_IH) of 2.1 V and typical low

threshold (V_IL) of 0.9 V. The input pins are conveniently driven with logic level PWM control signals derived from

3.3 V and 5 V digital power-controller devices. Wider hysteresis (typically 0.9 V) offers enhanced noise immunity

compared to traditional TTL logic implementations, where the hysteresis is typically less than 0.5 V.

2ED21091S06F also features tight control of the input pin threshold voltage levels which eases system design

considerations and ensures stable operation across temperature. The 2ED21091S06F has input pins that are

capable of sustaining voltages higher than the bias voltage applied on the Vcc pin of the device.

Figure 11 IN input thresholds

Datasheet

www.infineon.com/soi

11 of 25

V 2.10

2019-09-12

2ED21091S06F

650 V half bridge gate driver with integrated bootstrap diode

5.7

Undervoltage lockout

This IC provides undervoltage lockout protection on both the V_CC(logic and low-side circuitry) power supply

and the V_BS(high-side circuitry) power supply. Figure 12 is used to illustrate this concept; V_CC(or V_BS) is plotted

over time and as the waveform crosses the UVLO threshold (V_CCUV+/-or V_BSUV+/-) the undervoltage protection is

enabled or disabled.

Upon power-up, should the V_CCvoltage fail to reach the V_CCUV+threshold, the IC won’t turn-on. Additionally, if

the V_CCvoltage decreases below the V_CCUV-threshold during operation, the undervoltage lockout circuitry will

recognize a fault condition and shutdown the high and low-side gate drive outputs.

Upon power-up, should the V_BSvoltage fail to reach the V_BSUV+threshold, the IC won’t turn-on. Additionally, if

the V_BSvoltage decreases below the V_BSUV-threshold during operation, the undervoltage lockout circuitry will

recognize a fault condition, and shutdown the high-side gate drive outputs of the IC.

The UVLO protection ensures that the IC drives the external power devices only when the gate supply voltage is

sufficient to fully enhance the power devices. Without this feature, the gates of the external power switch

could be driven with a low voltage, resulting in the power switch conducting current while the channel

impedance is high; this could result in very high conduction losses within the power device and could lead to

power device failure.

V_CC

(or V_BS

)

V_CCUV+

(or V_BSUV+

)

V_CCUV-

(or V_BSUV-

)

Time

UVLO Protection

(Gate Drive Outputs Disabled)

Normal

Operation

Figure 12 UVLO protection

5.8

Bootstrap diode

An ultra-fast bootstrap diode is monolithically integrated for establishing the high side supply. The differential

resistor of the diode helps to avoid extremely high inrush currents when initially charging the bootstrap

capacitor. The integrated diode with its resistrance helps save cost and improve reliability by reducing external

components as shown below Figure 13 and Figure 14.

Figure 13 2ED210x with integrated components

Figure 14 Standard bootstrap gate driver

Datasheet

www.infineon.com/soi

12 of 25

V 2.10

2019-09-12

2ED21091S06F

650 V half bridge gate driver with integrated bootstrap diode

The low ohmic current limiting resistor provides essential advantages over other competitor devices with high

ohmic bootstrap structures. A low ohmic resistor such as in the 2ED210x family allows faster recharging of the

bootstrap capacitor during periods of small duty cycles on the low side transistor. The bootstrap diode is a real

pn-diode which works with all control algorithms of modern power electronics, such as trapezoidal or

sinusoidal motor drives control.

5.9

Calculating the bootstrap capacitance C_BS

Bootstrapping is a common method of pumping charges from a low potential to a higher one. With this

technique a supply voltage for the floating high side sections of the gate drive can be easily established

according to Figure 15. This method has the advantage of being simple and low cost but may force some

limitations on duty-cycle and on-time since they are limited by the requirement to refresh the charge in the

bootstrap capacitor. Proper capacitor choice can reduce drastically these limitations.

Figure 15 Half bridge bootstrap circuit in 2ED210x

When the low side MOSFET turns on, it will force the potential of pin V_Sto GND. The existing difference between

the voltage of the bootstrap capacitor V_CBSand V_CCresults in a charging current I_BSinto the capacitor C_BS. The

current I_BSis a pulse current and therefore the ESR of the capacitor C_BSmust be very small in order to avoid

losses in the capacitor that result in lower lifetime of the capacitor. This pin is on high potential again after low

side is turned off and high side is conducting current. But now the bootstrap diode D_BSblocks a reverse current,

so that the charges on the capacitor cannot flow back to the capacitor C_VCC. The bootstrap diode D_BSalso takes

over the blocking voltage between pin V_Band V_CC. The voltage of the bootstrap capacitor can now supply the

high side gate drive sections. It is a general design rule for the location of bootstrap capacitors C_BS, that they

must be placed as close as possible to the IC. Otherwise, parasitic resistors and inductances may lead to

voltage spikes, which may trigger the undervoltage lockout threshold of the individual high side driver section.

However, all parts of the 2ED210x family, which have the UVLO also contain a filter at each supply section in

order to actively avoid such undesired UVLO triggers.

The current limiting resistor R_BSaccording to Figure 15 reduces the peak of the pulse current during the low

side MOSFET turn-on. The pulse current will occur at each turn-on of the low side MOSFET, so that with

increasing switching frequency the capacitor C_BSis charged more frequently. Therefore a smaller capacitor is

suitable at higher switching frequencies. The bootstrap capacitor is mainly discharged by two effects: The high

side quiescent current and the gate charge of the high side MOSFET to be turned on.

Datasheet

www.infineon.com/soi

13 of 25

V 2.10

2019-09-12

2ED21091S06F

650 V half bridge gate driver with integrated bootstrap diode

The minimum size of the bootstrap capacitor is given by

ꢃ_ꢄꢅꢆꢅ

ꢀ_ꢁꢂ

=

∆ꢇ_ꢁꢂ

∆V_BSis the maximum allowable voltage drop at the bootstrap capacitor within a switching period, typically 1 V.

It is recommended to keep the voltage drop below the undervoltage lockout (UVLO) of the high side and limit

∆V_BS≤ (V_CC– V_F– V_GSmin– V_DSon

)

V_GSmin> V_BSUV-, V_GSminis the minimum gate source voltage we want to maintain and V_BSUV-is the high-side supply

undervoltage negative threshold.

V_CCis the IC voltage supply, V_Fis bootstrapdiode forward voltage and V_DSonis drain-source voltage of low side

MOSFET.

Please note, that the value Q_GTOTmay vary to a maximum value based on different factors as explained below

and the capacitor shows voltage dependent derating behavior of its capacitance.

The influencing factors contributing V_BSto decrease are:

- MOSFET turn on required Gate charge (Q_G)

- MOSFET gate-source leakage current (I_{LK_GS}

)

- Floating section quiescent current (I_QBS

)

- Floating section leakage current (I_LK)

- Bootstrap diode leakage current (I_{LK_DIODE}

- Charge required by the internal level shifters (ꢃ_ꢈꢂ): typical 1nC

- Bootstrap capacitor leakage current (I_{LK_CAP}

)

- High side on time (T_HON

)

Considering the above,

ꢃ_ꢄꢅꢆꢅ= ꢃ_ꢄ+ ꢃ_ꢈꢂ+ �ꢉ_ꢊꢁꢂ+ ꢉ_ꢈꢋ+ ꢉ_ꢈꢋ+ ꢉ_ꢈꢋ

+ ꢉ_ꢈꢋꢕ ∗ ꢖ_ꢗꢆꢘ

ꢒꢓꢔ

ꢌꢍ

ꢎꢏꢐꢎꢑ

I_{LK_CAP}is only relevant when using an electrolytic capacitor and can be ignored if other types of capacitors are

used. It is strongly recommend using at least one low ESR ceramic capacitor (paralleling electrolytic capacitor

and low ESR ceramic capacitor may result in an efficient solution).

The above C_BSequation is valid for pulse by pulse considerations. It is easy to see, that higher capacitance

values are needed, when operating continuously at small duty cycles of low side. The recommended bootstrap

capacitance is therefore in the range up to 4.7 μF for most switching frequencies. The performance of the

integrated bootstrap diode supports the requirement for small bootstrap capacitances.

5.10

Tolerant to negative tranisents on input pins

Typically the driver's ground pin is connected close to the source pin of the MOSFET or IGBT. The

microcontroller which sends the IN PWM signal refers to the same ground and in most cases there will be an

offset voltage between the microcontroller ground pin and driver ground because of ground bounce. The

2ED210x family can handle negative voltage spikes up to 5 V. The recommended operating level is at negative 4

V with absolute maximum of negative 5 V. Standard half bridge or high-side/low-side gate drivers only allow

negative voltage levels down to -0.3 V. The 2ED210x family has much better noise immunity capability on the

input pins.

Datasheet

www.infineon.com/soi

14 of 25

V 2.10

2019-09-12

2ED21091S06F

650 V half bridge gate driver with integrated bootstrap diode

Figure 16 Negative voltage tolerance on inputs of upto –5 V

5.11

Negative voltage transient tolerance of VS pin

A common problem in today’s high-power switching converters is the transient response of the switch node’s

voltage as the power switches transition on and off quickly while carrying a large current. A typical 3-phase

inverter circuit is shown in Figure 17, here we define the power switches and diodes of the inverter.

If the high-side switch (e.g., the IGBT Q1 in Figure 18) switches from on to off, while the U phase current is

flowing to an inductive load, a current commutation occurs from high-side switch (Q1) to the diode (D2) in

parallel with the low-side switch of the same inverter leg. At the same instance, the voltage node V_S1, swings

from the positive DC bus voltage to the negative DC bus voltage.

DC+ BUS

D3

D1

D5

Q1

Q3

Q5

W

V_S3

V

To

Input

Voltage

V_S2

U

Load

V_S1

D4

D2

D6

Q4

Q2

Q6

DC- BUS

Figure 17 Three phase inverter

Also when the V phase current flows from the inductive load back to the inverter (see Figure 18 C) and D)), and

Q4 IGBT switches on, the current commutation occurs from D3 to Q4. At the same instance, the voltage node,

V_S2, swings from the positive DC bus voltage to the negative DC bus voltage.

However, in a real inverter circuit, the VS voltage swing does not stop at the level of the negative DC bus, rather

it swings below the level of the negative DC bus. This undershoot voltage is called “negative V_Stransient”

Datasheet

www.infineon.com/soi

15 of 25

V 2.10

2019-09-12

2ED21091S06F

650 V half bridge gate driver with integrated bootstrap diode

DC+ BUS

D3

D1

D2

D3

Q1

ON

Q3

OFF

Q1

OFF

Q3

OFF

I_U

I_V

V_S1

V_S2

V_S1

V_S2

I_V

I_U

D2

D4

Q2

OFF

Q4

ON

Q2

OFF

Q4

OFF

DC- BUS

A)

Figure 18 A) Q1 conducting

D)

B)

B) D2 conducting

C)

C) D3 conducting

D) Q4 conducting

The circuit shown in Figure 19-A depicts one leg of the three phase inverter; Figure 19-B and 19-C show a

simplified illustration of the commutation of the current between Q1 and D2. The parasitic inductances in the

power circuit from the die bonding to the PCB tracks are lumped together in L_Cand L_Efor each IGBT. When the

high-side switch is on, V_S1is below the DC+ voltage by the voltage drops associated with the power switch and

the parasitic elements of the circuit. When the high-side power switch turns off, the load current momentarily

flows in the low-side freewheeling diode due to the inductive load connected to V_S1(the load is not shown in

these figures). This current flows from the DC- BUS (which is connected to the COM pin of the HVIC) to the load

and a negative voltage between V_S1and the DC- BUS is induced (i.e., the COM pin of the HVIC is at a higher

potential than the V_Spin).

DC+ BUS

L_C1

DC+ BUS

+

V_LC1

-

D1

Q1

Q2

Q1

OFF

Q1

ON

+

L_E1

L_C2

I_U

V_LE1

-

V_S1

-

I_U

V_LC2

+

D2

-

Q2

OFF

Q2

OFF

V_D2

+

-

L_E2

DC- BUS

V_LE2

+

DC- BUS

A

DC- BUS

C

B

Figure 19 Figure A shows the parasitic elements. Figure B shows the generation of VS positive. Figure C

shows the generation of VS negative

5.12

NTSOA – Negative Transient Safe Operating Area

In a typical motor drive system, dV/dt is typically designed to be in the range of 3 – 5 V / ns. The negative VS

transient voltage can exceed this range during some events such as short circuit and over-current shutdown,

when di/dt is greater than in normal operation.

Infineon’s HVICs have been designed for the robustness required in many of today’s demanding applications.

An indication of the 2ED21091S06F’s robustness can be seen in Figure 20, where the 2ED21091S06F’s Safe

Operating Area is shown at V_BS=15 V based on repetitive negative VS spikes. A negative VS transient voltage

falling in the grey area (outside SOA) may lead to IC permanent damage; viceversa unwanted functional

anomalies or permanent damage to the IC do not appear if negative Vs transients fall inside the SOA.

Datasheet

www.infineon.com/soi

16 of 25

V 2.10

2019-09-12

2ED21091S06F

650 V half bridge gate driver with integrated bootstrap diode

Recommended safe operating area

Figure 20 Negative VS transient SOA for 2ED21091S06F @ VBS=15 V

Even though the 2ED21091S06F has been shown able to handle these large negative VS transient conditions, it

is highly recommended that the circuit designer always limit the negative VS transients as much as possible by

careful PCB layout and component use.

5.13

Higher headroom for input to output signal transmission with logic

operation upto -11 V

If there is not enough voltage for the level shifter to transmit a valid signal to the high side. High side driver

doesn’t turn on. The level shifter circuit is with respect to COM (refer to Block Diagram on page 4), the voltage

from V_Bto COM is the supply voltage of level shifter. Under the condition of VS is negative voltage with respect

to COM, the voltage of VS - COM is decreased, as shown in Figure 21. There is a minimum operational supply

voltage of level shifter, if the supply voltage of level shifter is too low, the level shifter cannot pass through IN

signal to HO. The specification of VS is –11 V as the internal structure allows a voltage difference of 15 V

between Vcc and COM pins. If V_B– V_Svoltage is different, the minimum VS voltage changes accordingly.

VS

COM

- 11 V

Figure 21 Headroom for HV level shifter data transmission

Datasheet

www.infineon.com/soi

17 of 25

V 2.10

2019-09-12

2ED21091S06F

650 V half bridge gate driver with integrated bootstrap diode

5.14

Maximum switching frequency

The 2ED21091S06F is capable of switching at higher frequencies as compared to standard half-bridge or high

side / low side gate drivers. It is essential to ensure that the component is not thermally overloaded when

operating at higher frequencies. This can be checked by means of the thermal resistance junction to ambient

and the calculation or measurement of the dissipated power. The thermal resistance is given in the datasheet

(section 4) and refers to a specific layout. Changes of this layout may lead to an increased thermal resistance,

which will reduce the total dissipated power of the driver IC. One should therefore do temperature

measurements in order to avoid thermal overload under application relevant conditions of ambient

temperature and housing.

The maximum chip temperature T_Jcan be calculated with

ꢖ = Pd ∙ ꢚꢛℎ_ꢙꢜ+ ꢖ

, where T_{A_max}is the maximum ambient temperature.

ꢙ

ꢜ_ꢝꢞꢟ

The dissipated power Pd by the driver IC is a combination of several sources. These are explained in detail in

the application note “Advantages of Infineon’s Silicon on Insulator (SOI) technology based High Voltage Gate

Driver ICs (HVICs)”

Here is the example of the figures which estimates the gate driver IC junction temperature when switching a

given MOSFET at different switching frequencies.

150

Vbus = 400 V

Vbus = 200 V

125

100

75

50

25

125

225

325

425

525

Frequency (kHz)

*Assumptions for above curves: LLC topology, Power switch = IPP60R600P6, T_a= 25 °C, V_BUS= 400 V, V_CC= 12 V,

R_gon= 3.9 Ω, R_goff= 1 Ω

Figure 22 Estimated T_Jvs. Frequencies

Datasheet

www.infineon.com/soi

18 of 25

V 2.10

2019-09-12

2ED21091S06F

650 V half bridge gate driver with integrated bootstrap diode

5.15

PCB layout tips

Distance between high and low voltage components: It’s strongly recommended to place the components tied

to the floating voltage pins (V_Band V_S) near the respective high voltage portions of the device. Please see the

Case Outline information in this datasheet for the details.

Ground Plane: In order to minimize noise coulping, the ground plane should not be placed under or near the

high voltage floating side.

Gate Drive Loops: Current loops behave like antennas and are able to receive and transmit EM noise (see Figure

23). In order to reduce the EM coulping and improve the power switch turn on/off performance, the gate drive

loops must be reduced as much as possible. Moreover, current can be injected inside the gate drive loop via the

IGBT collector-to-gate parasitic capacitance. The parasitic auto-inductance of the gate loop contributes to

developing a voltage across the gate-emitter, thus increasing the possibility of a self turn-on effect.

Figure 23 Avoid antenna loops

Supply Capacitor: It is recommended to place a bypass capacitor (C_IN) between the V_CCand COM pins. A

ceramic 1μFceramic capacitor issuitable for most applications. Thiscomponent should be placed asclose as

possible to the pins in order to reduce parasitic elements.

Routing and Placement: Power stage PCB parasitic elements can contribute to large negative voltage

transients at the switch node; it is recommended to limit the phase voltage negative transients. In order to

avoid such conditions, it is recommended to 1) minimize the high-side emitter to low-side collector distance,

and 2) minimize the low-side emitter to negative bus rail stray inductance. However, where negative VS spikes

remain excessive, further steps may be taken to reduce the spike. This includes placing a resistor (5 Ω or less)

between the VS pin and the switch node (see Figure 24 - A), and in some cases using a clamping diode between

COM and V_S(see Figure 24 - B). See DT04-4 at www.infineon.com for more detailed explanations.

Figure 24 Resistor between the VS pin and the switch node and clamping diode between COM and VS

Datasheet

www.infineon.com/soi

19 of 25

V 2.10

2019-09-12

2ED21091S06F

650 V half bridge gate driver with integrated bootstrap diode

6

Qualification information¹

Table 7

Qualification information

Industrial²

Note: This family of ICs has passed JEDEC’s Industrial

qualification. Consumer qualification level is granted by

extension of the higher Industrial level.

Qualification level

Moisture sensitivity level

ESD

MSL3³, 260°C

DSO-8

(per IPC/JEDEC J-STD-020)

Class C3 (1.0 kV)

(per JEDEC standard JS-002)

Class 2 (1.5 kV)

Charged device model

Human body model

(per JEDEC standard JS-001)

Class II Level A

(per JESD85)

Yes

IC latch-up test

RoHS compliant

7

是否Rohs认证：	符合	生命周期：	Active
Reach Compliance Code：	compliant	Factory Lead Time：	26 weeks
风险等级：	5.75	Base Number Matches：	1

型号	制造商	描述	价格	文档
2ED21094S06J	INFINEON	650 V half bridge gate driver with integrated bootstrap diode	获取价格
2ED21094S06JXUMA1	INFINEON	Half Bridge Based Peripheral Driver,	获取价格
2ED2109S06F	INFINEON	650 V half bridge gate driver with integrated bootstrap diode	获取价格
2ED2110S06M	INFINEON	650 V high speed, high current high-side and low-side gate driver with typical 2.5 A source and sink currents in DSO-16 package for driving power MOSFETs and IGBTs.	获取价格
2ED21814S06J	INFINEON	650 V high-side and low-side gate driver with integrated bootstrap diode	获取价格
2ED21814S06JXUMA1	INFINEON	Half Bridge Based Peripheral Driver,	获取价格
2ED2181S06F	INFINEON	650 V high-side and low-side gate driver with integrated bootstrap diode	获取价格
2ED21824S06J	INFINEON	650 V high-side and low-side gate driver with integrated bootstrap diode	获取价格
2ED2182S06F	INFINEON	650 V half-bridge gate driver with integrated bootstrap diode	获取价格
2ED21834S06J	INFINEON	650 V half-bridge gate driver with integrated bootstrap diode	获取价格

2ED21091S06FXUMA1

2ED21091S06FXUMA1 概述

2ED21091S06FXUMA1 规格参数

2ED21091S06FXUMA1 数据手册

2ED21091S06FXUMA1 CAD模型

原理图符号

PCB 封装图

3D模型

2ED21091S06FXUMA1 相关器件

2ED21091S06FXUMA1 相关文章

热门型号