MODEL: KAPU
Housing material: Flame-resistant resin (black)
Isolation: Input to output to power
Minimum load: 5 V DC @ 10 mA
Frequency range: 0 – 130 pulses/min.
ON pulse width: 40 msec. – 0.8 sec. adjustable
Relay life:
Zero adjustment: 0 – 5 % (front)
Span adjustment: 50 – 100 % of range (front)
Output frequency adjustment: Preselecting range
with a rotary switch and fine control
≥ 5 × 10
7
cycles (mechanical)
≥ 10 cycles (electrical)
5
with span adjustment (50 – 100 %)
■ 5 V Pulse
Output pulse width adjustment:Three-turn screwdriver
adjustment (front)
Frequency range: 0 – 10 kHz
Low pulse width: 40 μsec. – 0.8 msec. adjustable
High level: 5 V ± 10 %
Low-end cutout: 0 to 10 % (front); a red LED assists in
adjusting the cutout point; turns on during the cutout.
Low level: ≤ 0.5 V
Load resistance: 600 Ω min.
■ Middle Range Frequency 5 V Pulse
Frequency range: 0 – 312 Hz
Low pulse width: 2 – 35 msec. adjustable
High level: 5 V ±10 %
INPUT SPECIFICATIONS
■ DC Current:
Shunt resistor attached to the input terminals (0.5 W)
Specify input resistance value for code Z.
■ DC Voltage: -300 – +300 V DC
Minimum span: 10 mV
Low level: ≤0.5 V
Load resistance: 600 Ω min.
■ Low Frequency 5 V Pulse
Frequency range: 0 – 130 pulses/min.
Low pulse width: 40 msec. – 0.8 sec. adjustable
High level: 5 V ± 10 %
Offset: Max. 1.5 times span
Input resistance
Span 10 – 100 mV : ≥ 10 kΩ
Span 0.1 – 1 V : ≥ 100 kΩ
Low level: ≤ 0.5 V
Span ≥ 1 V : ≥ 1 MΩ
Load resistance: 600 Ω min.
■ 24 V Pulse
OUTPUT SPECIFICATIONS
Note: For factory setting, maximum frequency of the
selected range is used to determine pulse width. Pulse
width is adjusted until the duty ratio becomes 50 % of the
maximum frequency. If this value lies outside of the
adjustable range, either maximum or minimum selectable
value will be used.
Frequency range: 0 – 130 pulses/min.
High pulse width: 40 msec. – 0.8 sec. adjustable
High level: 24 V ±10%
Low level: ≤ 0.5 V
Load current: 30 mA max.
Load resistance: 800 Ω min.
• Open Collector, 5V Pulse
■ Open Collector:
SPAN RANGE
SW No.
50 V DC @ 50 mA (resistive load)
MIN. (50%)
MAX. (100%)
Frequency range: 0 – 10 kHz
0 – 10 kHz
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
0 – 5 kHz
ON pulse width: 40 μsec. – 0.8 msec. adjustable
Saturation voltage: 0.6 V DC
0 – 5 kHz
0 – 2.5 kHz
0 – 1.25 kHz
0 – 625 Hz
0 – 312 Hz
0 – 156 Hz
0 – 78 Hz
0 – 39 Hz
0 – 20 Hz
0 – 10 Hz
0 – 5 Hz
0 – 2.5 kHz
0 – 1.25 kHz
0 – 625 Hz
0 – 312 Hz
0 – 156 Hz
0 – 78 Hz
0 – 39 Hz
0 – 20 Hz
0 – 10 Hz
0 – 5 Hz
■ Low Frequency Open Collector:
50 V DC @ 50 mA (resistive load)
Frequency range: 0 – 130 pulses/min.
ON pulse width: 40 msec. – 0.8 sec. adjustable
Saturation voltage: 0.6 V DC
■ Middle Range Frequency Open Collector:
50 V DC @ 50 mA (resistive load)
0 – 2.5 Hz
Frequency range: 0 – 312 Hz
0 – 2.5 Hz
0 – 1.25 Hz
ON pulse width: 2 – 35 msec. adjustable
Saturation voltage: 0.6 V DC
0 – 1.25 Hz
0 – 36 pulses/min.
0 – 18 pulses/min.
0 – 9 pulses/min.
0 – 36 pulses/min.
0 – 18 pulses/min.
■ Relay Contact: 120 V AC @ 200 mA (cos ø = 1)
240 V AC @ 100 mA (cos ø = 1)
24 V DC @ 200 mA (resistive load)
Maximum switching voltage: 380 V AC or 125V DC
Maximum switching power: 24 VA or 4.8 W
KAPU SPECIFICATIONS
ES-3582 Rev.13 Page 2/5
http://www.m-system.co.jp/